MAXIM MAX3390EEUD

19-2328; Rev 2; 11/07
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
The MAX3372E–MAX3379E and MAX3390E–MAX3393E
±15kV ESD-protected level translators provide the level
shifting necessary to allow data transfer in a multivoltage
system. Externally applied voltages, VCC and VL, set the
logic levels on either side of the device. A low-voltage
logic signal present on the VL side of the device appears
as a high-voltage logic signal on the VCC side of the
device, and vice-versa. The MAX3374E/MAX3375E/
MAX3376E/MAX3379E and MAX3390E–MAX3393E unidirectional level translators level shift data in one direction
(VL → VCC or VCC → VL) on any single data line. The
MAX3372E/MAX3373E and MAX3377E/MAX3378E bidirectional level translators utilize a transmission-gatebased design (Figure 2) to allow data translation in either
direction (V L ↔ V CC ) on any single data line. The
MAX3372E–MAX3379E and MAX3390E–MAX3393E
accept VL from +1.2V to +5.5V and VCC from +1.65V to
+5.5V, making them ideal for data transfer between lowvoltage ASICs/PLDs and higher voltage systems.
All devices in the MAX3372E–MAX3379E, MAX3390E–
MAX3393E family feature a three-state output mode that
reduces supply current to less than 1µA, thermal shortcircuit protection, and ±15kV ESD protection on the VCC
side for greater protection in applications that route signals externally. The MAX3372E/MAX3377E operate at a
guaranteed data rate of 230kbps. Slew-rate limiting
reduces EMI emissions in all 230kbps devices. The
MAX3373E–MAX3376E/MAX3378E/MAX3379E and
MAX3390E–MAX3393E operate at a guaranteed data rate
of 8Mbps over the entire specified operating voltage
range. Within specific voltage domains, higher data rates
are possible. (See the Timing Characteristics table.)
The MAX3372E–MAX3376E are dual level shifters
available in 3 x 3 UCSP™, 8-pin TDFN, and 8-pin
SOT23-8 packages. The MAX3377E/MAX3378E/
MAX3379E and MAX3390E–MAX3393E are quad level
shifters available in 3 x 4 UCSP, 14-pin TDFN, and 14pin TSSOP packages.
________________________Applications
SPI™, MICROWIRE™, and I2C Level
Translation
Low-Voltage ASIC Level Translation
Smart Card Readers
Cell-Phone Cradles
Portable POS Systems
Portable Communication Devices
Low-Cost Serial Interfaces
Cell Phones
GPS
Telecommunications Equipment
Features
♦ Guaranteed Data Rate Options
230kbps
8Mbps (+1.2V ≤ VL ≤ VCC ≤ +5.5V)
10Mbps (+1.2V ≤ VL ≤ VCC ≤ +3.3V)
16Mbps (+1.8V ≤ VL ≤ VCC ≤ +2.5V and +2.5V
≤ VL ≤ VCC ≤ +3.3V)
♦ Bidirectional Level Translation
(MAX3372E/MAX3373E and
MAX3377E/MAX3378E)
♦ Operation Down to +1.2V on VL
♦ ±15kV ESD Protection on I/O VCC Lines
♦ Ultra-Low 1µA Supply Current in Three-State
Output Mode
♦ Low-Quiescent Current (130µA typ)
♦ UCSP, TDFN, SOT23, and TSSOP Packages
♦ Thermal Short-Circuit Protection
Ordering Information
PART
TEMP
RANGE
MAX3372EEKA+T
-40°C to +85°C
PINPACKAGE
PKG
CODE
8 SOT23
K8S-3
+Denotes a lead-free package.
T = Tape and reel.
Ordering Information continued at end of data sheet.
Selector Guide appears at end of data sheet.
UCSP is a trademark of Maxim Integrated Products, Inc.
SPI is a trademark of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
Pin Configurations
TOP VIEW
I/O VL1
1
14
VCC
I/O VL2
2
13
I/0 VCC1
MAX3377E/
MAX3378E THREE-STATE 3
12
I/0 VCC2
N.C.
4
11
N.C.
I/O VL3
5
10
VL
I/O VL4
6
9
I/0 VCC3
GND
7
8
I/0 VCC4
TDFN-14
(3mm x 3mm)
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX3372E–MAX3379E/MAX3390E–MAX3393E
General Description
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND.)
VCC ...........................................................................-0.3V to +6V
I/O VCC_......................................................-0.3V to (VCC + 0.3V)
I/O VL_ ...........................................................-0.3V to (VL + 0.3V)
THREE-STATE...............................................-0.3V to (VL + 0.3V)
Short-Circuit Duration I/O VL, I/O VCC to GND...........Continuous
Short-Circuit Duration I/O VL or I/O VCC to GND
Driven from 40mA Source
(except MAX3372E and MAX3377E) .....................Continuous
Continuous Power Dissipation (TA = +70°C)
8-Pin SOT23 (derate 8.9mW/°C above +70°C)...........714mW
8-Pin TDFN (derate 18.2mW/°C above +70°C) ........1455mW
3 x 3 UCSP (derate 4.7mW/°C above +70°C) ............379mW
3 x 4 UCSP (derate 6.5mW/°C above +70°C) ............579mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) ........727mW
14-Pin TDFN (derate 18.2mW/°C above +70°C) ......1454mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +1.65V to +5.5V, VL = +1.2V to (VCC + 0.3V), GND = 0, I/O VL_ and I/O VCC_ unconnected, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V, VL = +1.8V, TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
POWER SUPPLIES
VL Supply Range
VCC Supply Range
Supply Current from VCC
Supply Current from VL
VCC Three-State Output Mode
Supply Current
VL Three-State Output Mode
Supply Current
Three-State Output Mode
Leakage Current
I/O VL_ and I/O VCC_
VL
1.2
5.5
V
VCC
1.65
5.50
V
IQVCC
130
300
µA
IQVL
16
100
µA
ITHREE-STATE-VCC
TA = +25°C, THREE-STATE = GND
0.03
1
µA
ITHREE-STATE-VL
TA = +25°C, THREE-STATE = GND
0.03
1
µA
ITHREE-STATE-LKG
TA = +25°C, THREE-STATE = GND
0.02
1
µA
TA = +25°C
0.02
1
µA
THREE-STATE Pin Input Leakage
ESD PROTECTION
IEC 1000-4-2 Air-Gap Discharge
I/O VCC (Note 3)
±8
IEC 1000-4-2 Contact Discharge
±8
Human Body Model
±15
kV
LOGIC-LEVEL THRESHOLDS (MAX3372E/MAX3377E)
2
I/O VL_ Input-Voltage High
VIHL
I/O VL_ Input-Voltage Low
VILL
VL - 0.2
_______________________________________________________________________________________
V
0.15
V
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
(VCC = +1.65V to +5.5V, VL = +1.2V to (VCC + 0.3V), GND = 0, I/O VL_ and I/O VCC_ unconnected, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V, VL = +1.8V, TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
I/O VCC_ Input-Voltage High
VIHC
I/O VCC_ Input-Voltage Low
VILC
I/O VL_ Output-Voltage High
VOHL
I/O VL_ source current = 20µA,
I/O VCC_ > VCC - 0.4V
I/O VL_ Output-Voltage Low
VOLL
I/O VL_ sink current = 20µA,
I/O VCC_ < 0.15V
I/O VCC_ Output-Voltage High
VOHC
I/O VCC_ source current = 20µA,
I/O VL _ > VL - 0.2V
I/O VCC_ Output-Voltage Low
VOLC
I/O VCC_ sink current = 20µA,
I/O VL_ < 0.15V
THREE-STATE Input-Voltage
High
VIL-THREE-STATE
THREE-STATE Input-Voltage
Low
VIL-THREE-STATE
MIN
TYP
MAX
UNITS
0.15
V
VCC - 0.4
V
0.67 ✕ VL
V
0.4
0.67 ✕ VCC
V
V
0.4
VL - 0.2
V
V
0.15
V
LOGIC-LEVEL THRESHOLDS (MAX3373E–MAX3376E/MAX3378E/MAX3379E and MAX3390E–MAX3393E)
I/O VL_ Input-Voltage High
VIHL
VL - 0.2
I/O VL_ Input-Voltage Low
VILL
I/O VCC_ Input-Voltage High
VIHC
I/O VCC_ Input-Voltage Low
VILC
I/O VL_ Output-Voltage High
VOHL
I/O VL_ source current = 20µA,
I/O VCC_ ≥ VCC - 0.4V
I/O VL_ Output-Voltage Low
VOLL
I/O VL_ sink current = 1mA,
I/O VCC_ ≤ 0.15V
I/O VCC_ Output-Voltage High
VOHC
I/O VCC_ source current = 20µA,
I/O VL_ ≥ VL - 0.2V
I/O VCC_ Output-Voltage Low
VOLC
I/O VCC_ sink current = 1mA,
I/O VL_ ≤ 0.15V
THREE-STATE Input-Voltage
High
VIH-THREE-STATE
THREE-STATE Input-Voltage
Low
VIL-THREE-STATE
V
0.15
V
0.15
V
VCC - 0.4
V
0.67 ✕ VL
V
0.4
0.67 ✕ VCC
V
V
0.4
VL - 0.2
V
V
0.15
V
_______________________________________________________________________________________
3
MAX3372E–MAX3379E/MAX3390E–MAX3393E
ELECTRICAL CHARACTERISTICS (continued)
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
TIMING CHARACTERISTICS
(VCC = +1.65V to +5.5V, VL = +1.2V to (VCC + 0.3V), GND = 0, RLOAD = 1MΩ, I/O test signal of Figure 1, TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.3V, VL = +1.8V, TA = +25°C, unless otherwise noted.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MAX3372E/MAX3377E (CLOAD = 50pF)
I/O VCC_ Rise Time (Note 4)
tRVCC
1100
ns
I/O VCC_ Fall Time (Note 5)
tFVCC
1000
ns
I/O VL _ Rise Time (Note 4)
tRVL
600
ns
I/O VL _ Fall Time (Note 5)
Propagation Delay
Channel-to-Channel Skew
tFVL
1100
ns
I/OVL-VCC
Driving I/O VL _
1.6
I/OVCC-VL
Driving I/O VCC_
1.6
tSKEW
Maximum Data Rate
Each translator equally loaded
CL = 25pF
500
230
µs
ns
kbps
MAX3373E–MAX3376E/MAX3378E/MAX3379E and MAX3390E–MAX3393E (CLOAD = 15pF, Driver Output Impedance ≤ 50Ω)
+1.2V ≤ VL ≤ VCC ≤ +5.5V
I/O VCC_ Rise Time (Note 4)
tRVCC
I/O VCC_ Fall Time (Note 5)
tFVCC
I/O VL _ Rise Time (Note 4)
tRVL
I/O VL _ Fall Time (Note 5)
tLFV
7
25
Open-drain driving
170
400
6
37
Open-drain driving
20
50
8
30
Open-drain driving
180
400
3
30
Open-drain driving
30
60
I/OVL-VCC
Driving I/O VL _
I/OVCC-VL
Driving I/O VCC_
Propagation Delay
Channel-to-Channel Skew
Maximum Data Rate
4
tSKEW
Each translator
equally loaded
Open-drain driving
Open-drain driving
Open-drain driving
5
30
210
1000
4
30
190
1000
20
Open-drain driving
50
ns
ns
ns
ns
ns
ns
8
Mbps
500
kbps
_______________________________________________________________________________________
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
(VCC = +1.65V to +5.5V, VL = +1.2V to (VCC + 0.3V), GND = 0, RLOAD = 1MΩ, I/O test signal of Figure 1, TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.3V, VL = +1.8V, TA = +25°C, unless otherwise noted.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
+1.2V ≤ VL ≤ VCC ≤ +3.3V
I/O VCC_ Rise Time (Note 4)
tRVCC
25
ns
I/O VCC_ Fall Time (Note 5)
tFVCC
30
ns
I/O VL _ Rise Time (Note 4)
tRVL
30
ns
I/O VL _ Fall Time (Note 5)
tFVL
30
ns
Propagation Delay
Channel-to-Channel Skew
I/OVL-VCC
Driving I/O VL _
20
I/OVCC-VL
Driving I/O VCC_
Each translator equally loaded
20
tSKEW
Maximum Data Rate
10
10
ns
ns
Mbps
+2.5V ≤ VL ≤ VCC ≤ +3.3V
I/O VCC_ Rise Time (Note 4)
tRVCC
15
ns
I/O VCC_ Fall Time (Note 5)
tFVCC
15
ns
I/O VL _ Rise Time (Note 4)
tRVL
15
ns
I/O VL _ Fall Time (Note 5)
tFVL
15
ns
Propagation Delay
Channel-to-Channel Skew
I/OVL-VCC
Driving I/O VL _
15
I/OVCC-VL
Driving I/O VCC_
15
Each translator equally loaded
10
tSKEW
Maximum Data Rate
16
ns
ns
Mbps
+1.8V ≤ VL ≤ VCC ≤ +2.5V
I/O VCC_ Rise Time (Note 4)
tRVCC
15
ns
I/O VCC_ Fall Time (Note 5)
tFVCC
15
ns
I/O VL _ Rise Time (Note 4)
tRVL
15
ns
I/O VL _ Fall Time (Note 5)
tFVL
15
ns
Propagation Delay
Channel-to-Channel Skew
Maximum Data Rate
I/OVL-VCC
Driving I/O VL _
15
I/OVCC-VL
Driving I/O VCC_
15
tSKEW
Each translator equally loaded
10
16
ns
ns
Mbps
Note 1: All units are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed by design
and not production tested.
Note 2: For normal operation, ensure VL < (VCC + 0.3V). During power-up, VL > (VCC + 0.3V) will not damage the device.
Note 3: To ensure maximum ESD protection, place a 1µF capacitor between VCC and GND. See Applications Circuits.
Note 4: 10% to 90%
Note 5: 90% to 10%
_______________________________________________________________________________________
5
MAX3372E–MAX3379E/MAX3390E–MAX3393E
TIMING CHARACTERISTICS (continued)
Typical Operating Characteristics
(RLOAD = 1MΩ, TA = +25°C, unless otherwise noted. All 230kbps TOCs apply to MAX3372E/MAX3377E only. All 8Mbps and
500kbps TOCs apply to MAX3373E–MAX3376E/MAX3378E/MAX3379E and MAX3390E–MAX3393E only.)
VCC SUPPLY CURRENT vs. SUPPLY VOLTAGE
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
300
500kbps, OPEN-DRAIN, CLOAD = 15pF
230kbps, CLOAD = 50pF
100
500kbps, OPEN-DRAIN, CLOAD = 15pF
2.5
2.0
8Mbps, CLOAD = 15pF
1.5
1.0
230kbps, CLOAD = 50pF
8Mbps, CLOAD = 15pF
250
150
3.30
3.85
4.40
4.95
0
1.65
5.50
2.20
2.75
3.30
VCC SUPPLY CURRENT vs. TEMPERATURE
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
4.95
5.50
-40
350
300
SUPPLY CURRENT (μA)
1200
8Mbps, CLOAD = 15pF
1000
500kbps, OPEN-DRAIN, CLOAD = 15pF
600
8Mbps
250
200
150
500kbps, OPEN-DRAIN
100
230kbps, CLOAD = 50pF
200
0
35
85
60
25
40
55
70
85
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
DATA RATE = 230kbps
tLH
10
8
tHL
6
4
500
40
50
70
100
85
tLH
200
150
DATA RATE = 500kbps,
OPEN-DRAIN
100
tHL
50
DATA RATE = 8Mbps
0
30
55
2
tHL
0
20
40
250
RISE/FALL TIME (ns)
14
12
25
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
MAX3372E toc08
16
RISE/FALL TIME (ns)
1000
10
CAPACITIVE LOAD (pF)
18
MAX3372E toc07
tLH
230kbps
100
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
1500
500kbps, OPEN-DRAIN
1000
0
10
CAPACITIVE LOAD (pF)
2000
8Mbps
1500
500
TEMPERATURE (°C)
2500
85
60
2000
0
10
35
2500
230kbps
50
-15
10
VCC SUPPLY CURRENT vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
MAX3372E toc05
1400
-40
-15
TEMPERATURE (°C)
VL SUPPLY CURRENT vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
MAX3372E toc04
1600
400
4.40
VCC (V)
VCC (V)
800
3.85
MAX3372E toc06
2.75
230kbps, CLOAD = 50pF
50
SUPPLY CURRENT (μA)
2.20
500kbps, OPEN-DRAIN, CLOAD = 15pF
200
0
1.65
SUPPLY CURRENT (μA)
300
100
0.5
0
60
70
80
CAPACITIVE LOAD (pF)
6
350
MAX3372E toc09
200
3.0
SUPPLY CURRENT (μA)
400
400
MAX3372E toc02
8Mbps, CLOAD = 15pF
SUPPLY CURRENT (mA)
SUPPLY CURRENT (μA)
500
3.5
MAX3372E toc01
600
VL SUPPLY CURRENT vs. TEMPERATURE
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
MAX3372E toc03
VL SUPPLY CURRENT vs. SUPPLY VOLTAGE
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
RISE/FALL TIME (ns)
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
90
100
0
10
15
20
25
30
35
40
CAPACITIVE LOAD (pF)
45
50
10
15
20
25
30
35
40
CAPACITIVE LOAD (pF)
_______________________________________________________________________________________
45
50
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
tPHL
500
400
300
tPLH
200
DATA RATE = 230kbps
tPHL
9
6
300
200
DATA RATE = 500kbps,
OPEN-DRAIN
150
100
tPHL
50
tPLH
0
0
20
30
40
50
60
70
80
90
0
100
10
15
20
25
30
35
40
45
50
10
15
20
25
30
35
40
45
50
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +2.5V, VL = +1.8V)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +2.5V, VL = +1.8V)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +2.5V, VL = +1.8V)
12
tLH
1500
1000
DATA RATE = 230kbps
10
tLH
8
6
tHL
4
300
tLH
250
RISE/FALL TIME (ns)
RISE/FALL TIME (ns)
2000
DATA RATE = 8Mbps
MAX3372E toc15
14
MAX3372E toc13
2500
200
DATA RATE = 500kbps,
OPEN-DRAIN
150
100
tHL
500
50
2
tHL
0
0
20
30
40
50
60
70
80
90
100
0
10
15
20
25
30
35
40
45
50
10
15
20
25
30
35
40
45
50
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
tHL
1000
8
tLH
6
250
RISE/FALL TIME (ns)
10
4
MAX3372E toc18
DATA RATE = 8Mbps
RISE/FALL TIME (ns)
2000
300
MAX3372E toc17
DATA RATE = 230kbps
1500
12
MAX3372E toc16
2500
RISE/FALL TIME (ns)
tPLH
250
3
MAX3372E toc12
12
100
RISE/FALL TIME (ns)
MAX3372E toc11
DATA RATE = 8Mbps
PROPAGATION DELAY vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
MAX3372E toc14
PROPAGATION DELAY (ns)
600
15
PROPAGATION DELAY (ns)
MAX3372E toc10
700
PROPAGATION DELAY vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
PROPAGATION DELAY (ns)
PROPAGATION DELAY vs. CAPACITIVE LOAD
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V)
tLH
200
DATA RATE = 500kbps,
OPEN-DRAIN
150
100
tHL
500
tHL
2
tLH
0
20
30
40
50
60
50
0
70
80
CAPACITIVE LOAD (pF)
90
100
0
10
15
20
25
30
35
40
CAPACITIVE LOAD (pF)
45
50
10
15
20
25
30
35
40
45
50
CAPACITIVE LOAD (pF)
_______________________________________________________________________________________
7
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Typical Operating Characteristics (continued)
(RLOAD = 1MΩ, TA = +25°C, unless otherwise noted. All 230kbps TOCs apply to MAX3372E/MAX3377E only. All 8Mbps and
500kbps TOCs apply to MAX3373E–MAX3376E/MAX3378E/MAX3379E and MAX3390E–MAX3393E only.)
Typical Operating Characteristics (continued)
(RLOAD = 1MΩ, TA = +25°C, unless otherwise noted. All 230kbps TOCs apply to MAX3372E/MAX3377E only. All 8Mbps and
500kbps TOCs apply to MAX3373E–MAX3376E/MAX3378E/MAX3379E and MAX3390E–MAX3393E only.)
tPHL
400
300
200
100
5
tPHL
4
3
2
tPLH
300
250
tPHL
30
40
50
60
70
80
90
10
100
200
DATA RATE = 500kbps,
OPEN-DRAIN
150
100
tPHL
0
0
20
tPLH
50
1
0
MAX3372E toc21
MAX3372E toc20
DATA RATE = 8Mbps
PROPAGATION DELAY (ns)
500
6
PROPAGATION DELAY (ns)
DATA RATE = 230kbps
600
15
20
25
30
35
40
45
10
50
15
20
25
30
40
45
50
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +2.5V, VL = +1.8V)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +2.5V, VL = +1.8V)
RISE/FALL TIME vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +2.5V, VL = +1.8V)
tHL
1000
500
8
tLH
6
4
40
50
60
70
80
90
100
200
tLH
150
DATA RATE = 500kbps,
OPEN-DRAIN
tHL
50
0
30
250
100
tLH
20
300
tHL
2
0
350
MAX3373E toc24
10
RISE/FALL TIME (ns)
2000
DATA RATE = 8Mbps
RISE/FALl TIME (ns)
DATA RATE = 230kbps
1500
12
MAX3372E toc22
2500
0
10
20
30
40
50
10
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
20
30
40
CAPACITIVE LOAD (pF)
MAX3372E toc26
RAIL-TO-RAIL DRIVING
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V,
CLOAD = 15pF, DATA RATE = 8Mbps)
MAX3372E toc25
RAIL-TO-RAIL DRIVING
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V,
CLOAD = 50pF, DATA RATE = 230kbps)
I/O VL_
1V/div
I/O VL_
1V/div
I/O VCC_
2V/div
I/O VCC_
2V/div
1μs/div
8
35
CAPACITIVE LOAD (pF)
MAX3372E toc23
PROPAGATION DELAY (ns)
MAX3372E toc19
700
PROPAGATION DELAY vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
PROPAGATION DELAY vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
PROPAGATION DELAY vs. CAPACITIVE LOAD
(DRIVING I/O VCC, VCC = +3.3V, VL = +1.8V)
RISE/FALL TIME (ns)
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
200ns/div
_______________________________________________________________________________________
50
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
OPEN-DRAIN DRIVING
(DRIVING I/O VL, VCC = +3.3V, VL = +1.8V,
CLOAD = 15pF, DATA RATE = 500kbps)
EXITING THREE-STATE OUTPUT MODE
(VCC = +3.3V, VL = +1.8V, CLOAD = 50pF)
MAX3372E toc27
MAX3372E toc28
2V/div
I/O VCC_
I/O VL_
1V/div
1V/div
I/O VL_
I/O VCC_
2V/div
1V/div
THREE-STATE
2μs/div
200ns/div
Pin Description
PIN
3x4
UCSP
3x3
UCSP
TDFN
8
TDFN
14
NAME
5
C2
6
1
I/O VL1
Input/Output 1. Referenced to VL. (Note 6)
TSSOP SOT23-8
FUNCTION
A1
2
A2
3
4
C3
8
2
I/O VL2
Input/Output 2. Referenced to VL. (Note 6)
A3
4
—
—
—
5
I/O VL3
Input/Output 3. Referenced to VL. (Note 6)
A4
5
—
—
—
6
I/O VL4
Input/Output 4. Referenced to VL. (Note 6)
B1
14
7
A1
4
14
VCC
VCC Input Voltage +1.65V ≤ VCC ≤ +5.5V.
B2
1
3
C1
7
10
VL
B3
8
6
B1
5
3
THREESTATE
Logic Input Voltage +1.2V ≤ VL ≤ (VCC + 0.3V)
Three-State Output Mode Enable. Pull THREE-STATE low
to place device in three-state output mode. I/O VCC_ and
I/O VL_ are high impedance in three-state output mode.
Note: Logic referenced to VL (for logic thresholds see the
Electrical Characteristics table).
B4
7
2
B3
2
7
GND
C1
13
8
A2
3
13
I/O VCC1
Ground
Input/Output 1. Referenced to VCC. (Note 6)
C2
12
1
A3
1
12
I/O VCC2
Input/Output 2. Referenced to VCC. (Note 6)
C3
11
—
—
—
9
I/O VCC3
Input/Output 3. Referenced to VCC. (Note 6)
C4
10
—
—
—
8
I/O VCC4
Input/Output 4. Referenced to VCC. (Note 6)
—
6, 9
—
B2
—
4, 11
N.C.
—
—
—
—
EP
EP
EP
No Connection. Not internally connected.
Exposed Pad. Connect to ground.
Note 6: For unidirectional devices (MAX3374E/MAX3375E/MAX3376E/MAX3379E and MAX3390E–MAX3393E) see the Pin
Configurations for input/output configurations.
_______________________________________________________________________________________
9
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Typical Operating Characteristics (continued)
(RLOAD = 1MΩ, TA = +25°C, unless otherwise noted. All 230kbps TOCs apply to MAX3372E/MAX3377E only. All 8Mbps and
500kbps TOCs apply to MAX3373E–MAX3376E/MAX3378E/MAX3379E and MAX3390E–MAX3393E only.)
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
Detailed Description
The MAX3372E–MAX3379E and MAX3390E–MAX3393E
ESD-protected level translators provide the level shifting
necessary to allow data transfer in a multivoltage system.
Externally applied voltages, VCC and VL, set the logic levels on either side of the device. A low-voltage logic signal
present on the VL side of the device appears as a highvoltage logic signal on the VCC side of the device, and
vice-versa. The MAX3374E/MAX3375E/MAX3376E/
MAX3379E and MAX3390E–MAX3393E unidirectional
level translators level shift data in one direction (VL →
V CC or V CC → V L ) on any single data line. The
MAX3372E/MAX3373E and MAX3377E/MAX3378E bidirectional level translators utilize a transmission-gatebased design (see Figure 2) to allow data translation in
either direction (VL ↔ VCC) on any single data line. The
MAX3372E–MAX3379E and MAX3390E–MAX3393E
VL
accept VL from +1.2V to +5.5V and VCC from +1.65V to
+5.5V, making them ideal for data transfer between lowvoltage ASICs/PLDs and higher voltage systems.
All devices in the MAX3372E–MAX3379E, MAX3390E–
MAX3393E family feature a three-state output mode that
reduces supply current to less than 1µA, thermal shortcircuit protection, and ±15kV ESD protection on the VCC
side for greater protection in applications that route signals externally. The MAX3372E/MAX3377E operate at a
guaranteed data rate of 230kbps. Slew-rate limiting
reduces EMI emissions in all 230kbps devices. The
MAX3373E–MAX3376E/MAX3378E/MAX3379E and
MAX3390E–MAX3393E operate at a guaranteed data rate
of 8Mbps over the entire specified operating voltage
range. Within specific voltage domains, higher data rates
are possible. (See the Timing Characteristics table.)
VL
VCC
VL
VCC
VL
VCC
MAX3372E–MAX3379E
AND MAX3390E–MAX3393E
MAX3372E–MAX3379E
AND MAX3390E–MAX3393E
DATA
DATA
GND
RLOAD
I/O VL_
(tRISE,
tFALL < 10ns)
CLOAD
CLOAD
RLOAD
GND
I/O VCC_
(tRISE,
tFALL < 10ns)
tPD-VCC-LH
tPD-VCC-HL
I/O VCC_
tPD-VL-LH
tPD-VL-HL
tRVL
tFVL
I/O VL _
tRVCC
Figure 1a. Rail-to-Rail Driving I/O VL
10
I/O VCC_
I/O VL _
I/O VCC_
I/O VL _
VCC
tFVCC
Figure 1b. Rail-to-Rail Driving I/O VCC
______________________________________________________________________________________
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
Speed-Up Circuitry
The MAX3373E–MAX3376E/MAX3378E/MAX3379E and
MAX3390E–MAX3393E feature a one-shot generator that
decreases the rise time of the output. When triggered,
MOSFETs PU1 and PU2 turn on for a short time to pull up
VL
I/O VL_ and I/O VCC_ to their respective supplies (see
Figure 2b). This greatly reduces the rise time and propagation delay for the low-to-high transition. The scope
photo of Rail-to-Rail Driving for 8Mbps Operation in the
Typical Operating Characteristics shows the speed-up
circuitry in operation.
Rise-Time Accelerators
The MAX3373E–MAX3376E/MAX3378E/MAX3379E and
the MAX3390E–MAX3393E have internal rise-time
accelerators allowing operation up to 16Mbps. The
rise-time accelerators are present on both sides of the
device and act to speed up the rise time of the input
and output of the device, regardless of the direction of
the data. The triggering mechanism for these accelerators is both level and edge sensitive. To prevent false
triggering of the rise-time accelerators, signal fall times
of less than 20ns/V are recommended for both the
inputs and outputs of the device. Under less noisy conditions, longer signal fall times may be acceptable.
VL
VCC
VL
VCC
VL
VCC
MAX3372E–MAX3379E
AND MAX3390E–MAX3393E
DATA
DATA
CLOAD
GND
MAX3373E–MAX3376E,
MAX3378E/MAX3379E
AND MAX3390E–MAX3393E
I/O VCC_
I/O VL_
I/O VCC_
I/O VL_
VCC
CLOAD
GND
RLOAD
RLOAD
I/O VCC_
I/O VL_
tPD-VCC-HL
tPD-VL-LH
tPD-VCC-LH
tPD-VL-HL
I/O VL_
I/O VCC_
tRVCC
tFVCC
Figure 1c. Open-Drain Driving I/O VCC
tRVL
tFVL
Figure 1d. Open-Drain Driving I/O VL
______________________________________________________________________________________
11
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Level Translation
For proper operation ensure that +1.65V ≤ V CC ≤
+5.5V, +1.2V ≤ VL ≤ +5.5V, and VL ≤ (VCC + 0.3V).
During power-up sequencing, VL ≥ (VCC + 0.3V) will
not damage the device. During power-supply sequencing, when VCC is floating and VL is powering up, a current may be sourced, yet the device will not latch up.
The speed-up circuitry limits the maximum data rate for
devices in the MAX3372E–MAX3379E, MAX3390E–
MAX3393E family to 16Mbps. The maximum data rate
also depends heavily on the load capacitance (see the
Typical Operating Characteristics), output impedance
of the driver, and the operational voltage range (see the
Timing Characteristics table).
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
at I/O VL_ to exceed (VL + 0.3V), or the voltage at I/O
VCC_ to exceed (VCC + 0.3V).
Three-State Output Mode
Pull THREE-STATE low to place the MAX3372E–
MAX3379E and MAX3390E–MAX3393E in three-state output mode. Connect THREE-STATE to VL (logic-high) for
normal operation. Activating the three-state output mode
disconnects the internal 10kΩ pullup resistors on the I/O
VCC and I/O VL lines. This forces the I/O lines to a highimpedance state, and decreases the supply current to
less than 1µA. The high-impedance I/O lines in threestate output mode allow for use in a multidrop network.
When in three-state output mode, do not allow the voltage
Thermal Short-Circuit Protection
Thermal overload detection protects the MAX3372E–
MAX3379E and MAX3390E–MAX3393E from short-circuit
fault conditions. In the event of a short-circuit fault, when
the junction temperature (TJ) reaches +152°C, a thermal
sensor signals the three-state output mode logic to force
the device into three-state output mode. When TJ has
cooled to +142°C, normal operation resumes.
VCC
VL
P
P
GATE
BIAS
I/O VL
I/O VCC
N
Figure 2a. Functional Diagram, MAX3372E/MAX3377E (1 I/O line)
VCC
VL
PU1
ONE-SHOT
BLOCK
ONE-SHOT
BLOCK
PU2
GATE
BIAS
I/O VL_
N
I/O VCC_
Figure 2b. Functional Diagram, MAX3373E/MAX3378E (1 I/O line)
12
______________________________________________________________________________________
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
ESD protection can be tested in various ways. The I/O
VCC lines of this product family are characterized for
protection to the following limits:
1) ±15kV using the Human Body Model
2) ±8kV using the Contact Discharge method specified
in IEC 1000-4-2
3) ±10kV using IEC 1000-4-2’s Air-Gap Discharge
method
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 3a shows the Human Body Model and Figure 3b
shows the current waveform it generates when discharged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest, which is then discharged into the test device
through a 1.5kΩ resistor.
RC 1MΩ
CHARGE-CURRENTLIMIT RESISTOR
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifically refer to integrated circuits. The MAX3372E–
MAX3379E and MAX3390E–MAX3393E help to design
equipment that meets Level 3 of IEC 1000-4-2, without
the need for additional ESD-protection components.
The major difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2, because series resistance is
lower in the IEC 1000-4-2 model. Hence, the ESD withstand voltage measured to IEC 1000-4-2 is generally
lower than that measured using the Human Body Model.
Figure 4a shows the IEC 1000-4-2 model, and Figure 4b
shows the current waveform for the ±8kV, IEC 1000-4-2,
Level 4, ESD contact-discharge test.
The air-gap test involves approaching the device with a
charged probe. The contact-discharge method connects the probe to the device before the probe
is energized.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resistance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. Of course, all pins require this protection during manufacturing, not just inputs and outputs.
Therefore, after PCB assembly, the Machine Model is
less relevant to I/O ports.
RD 1500Ω
IP 100%
90%
DISCHARGE
RESISTANCE
Ir
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
HIGHVOLTAGE
DC
SOURCE
Cs
100pF
STORAGE
CAPACITOR
DEVICEUNDERTEST
36.8%
10%
0
0
Figure 3a. Human Body ESD Test Model
tRL
TIME
tDL
CURRENT WAVEFORM
Figure 3b. Human Body Current Waveform
______________________________________________________________________________________
13
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures are
incorporated on all pins to protect against electrostatic
discharges encountered during handling and assembly.
The I/O VCC lines have extra protection against static
electricity. Maxim’s engineers have developed state-ofthe-art structures to protect these pins against ESD of
±15kV without damage. The ESD structures withstand
high ESD in all states: normal operation, three-state
output mode, and powered down. After an ESD event,
Maxim’s E versions keep working without latchup,
whereas competing products can latch and must be
powered down to remove latchup.
I
100%
90%
RC 50MΩ to 100MΩ
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
Cs
150pF
RD 330Ω
DISCHARGE
RESISTANCE
I PEAK
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
DEVICEUNDERTEST
STORAGE
CAPACITOR
10%
t
t r = 0.7ns to 1ns
30ns
60ns
Figure 4a. IEC 1000-4-2 ESD Test Model
Figure 4b. IEC 1000-4-2 ESD Generator Current Waveform
Applications Information
Power-Supply Decoupling
To reduce ripple and the chance of transmitting incorrect data, bypass VL and VCC to ground with a 0.1µF
capacitor. See the Typical Operating Circuit. To ensure
full ±15kV ESD protection, bypass VCC to ground with a
1µF capacitor. Place all capacitors as close to the
power-supply inputs as possible.
I2C Level Translation
The MAX3373E–MAX3376E, MAX3378E/MAX3379E
and MAX3390E–MAX3393E level-shift the data present
on the I/O lines between +1.2V and +5.5V, making
them ideal for level translation between a low-voltage
ASIC and an I2C device. A typical application involves
interfacing a low-voltage microprocessor to a 3V or 5V
D/A converter, such as the MAX517.
Push-Pull vs. Open-Drain Driving
All devices in the MAX3372E–MAX3379E and
MAX3390E–MAX3393E family may be driven in a pushpull configuration. The MAX3373E–MAX3376E/
MAX3378E/MAX3379E and MAX3390E–MAX3393E
include internal 10kΩ resistors that pull up I/O VL_ and
I/O VCC_ to their respective power supplies, allowing
operation of the I/O lines with open-drain devices. See
the Timing Characteristics table for maximum data rates
when using open-drain drivers.
Typical Operating Circuit
+1.8V
+3.3V
0.1μF
0.1μF
VL
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3378E–MAX3383E
DATA
14
I/O VL_
I/O VCC_
DATA
______________________________________________________________________________________
1μF
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3372E/MAX3373E
DATA
I/O VL1
I/O VCC1
I/O VL2
I/O VCC2
DATA
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3374E
I VL1
DATA
I VL2
O VCC1
O VCC2
DATA
______________________________________________________________________________________
15
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Applications Circuits
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Applications Circuits (continued)
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3375E
DATA
O VL1
I VCC1
I VL2
O VCC2
DATA
+1.8V
+3.3V
0.1μF
0.1μF
VL
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3376E
DATA
16
O VL1
I VCC1
O VL2
I VCC2
DATA
______________________________________________________________________________________
1μF
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3377E/MAX3378E
DATA
I/O VL1
I/O VCC1
I/O VL2
I/O VL3
I/O VL4
I/O VCC2
I/O VCC3
I/O VCC4
DATA
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3379E
DATA
I VL1
O VCC1
I VL2
O VCC2
I VL3
I VL4
O VCC3
O VCC4
DATA
______________________________________________________________________________________
17
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Applications Circuits (continued)
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
Applications Circuits (continued)
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3390E
I VL1
O VL1
DATA
I VL2
O VCC2
I VL3
I VL4
O VCC3
O VCC4
DATA
+1.8V
+3.3V
0.1μF
0.1μF
VL
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3391E
DATA
O VL1
O VL2
I VL3
I VL4
18
I VCC1
I VCC2
O VCC3
O VCC4
DATA
______________________________________________________________________________________
1μF
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3392E
DATA
O VL1
I VCC1
O VL2
I VCC2
O VL3
I VL4
I VCC3
O VCC4
DATA
+1.8V
+3.3V
0.1μF
0.1μF
VL
1μF
VCC
THREE-STATE
+1.8V
SYSTEM
CONTROLLER
+3.3V
SYSTEM
MAX3393E
DATA
O VL1
O VL2
O VL3
I VL4
I VCC1
I VCC2
I VCC3
I VCC4
DATA
______________________________________________________________________________________
19
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Applications Circuits (continued)
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Selector Guide
LEVEL
TRANSLATION
Tx/
Rx†
MAX3372EEKA+T
Bi
2/2
MAX3372EEBL+T
Bi
2/2
MAX3372EETA+T
Bi
2/2
AQG
MAX3373EEKA+T
Bi
2/2
AAKS
PART
DATA
RATE
TOP
MARK
Ordering Information (continued)
PART
TEMP
RANGE
MAX3372EEBL+T
-40°C to +85°C
9 UCSP
(1.5mm x 1.5mm)
MAX3372EETA+T
-40°C to +85°C
8 TDFN-EP**
(3mm x 3mm)
MAX3373EEKA+T
-40°C to +85°C 8 SOT23
MAX3373EEBL+T
9 UCSP
-40°C to +85°C
(1.5mm x 1.5mm)
MAX3373EETA+T
-40°C to +85°C
MAX3374EEKA+T
-40°C to +85°C 8 SOT23
MAX3374EEBL+T
-40°C to +85°C
9 UCSP
(1.5mm x 1.5mm)
MAX3374EETA+T
-40°C to +85°C
8 TDFN-EP**
(3mm x 3mm)
MAX3375EEKA+T
-40°C to +85°C 8 SOT23
MAX3375EEBL+T
-40°C to +85°C
9 UCSP
(1.5mm x 1.5mm)
AAX
MAX3375EETA+T
-40°C to +85°C
8 TDFN-EP**
(3mm x 3mm)
MAX3376EEKA+T
-40°C to +85°C 8 SOT23
MAX3376EEBL+T
9 UCSP
-40°C to +85°C
(1.5mm x 1.5mm)
MAX3376EETA+T
-40°C to +85°C
MAX3377EEUD
-40°C to +85°C 14 TSSOP
MAX3377EEBC+T
-40°C to +85°C
9 UCSP
(1.5mm x 1.5mm)
MAX3377EETD+T
-40°C to +85°C
14 TDFN-EP**
(3mm x 3mm)
MAX3378EEUD
-40°C to +85°C 14 TSSOP
MAX3378EEBC+T
-40°C to +85°C
12 UCSP
(1.5mm x 2.0mm)
MAX3378EETD+T
-40°C to +85°C
14 TDFN-EP**
(3mm x 3mm)
AAKO
230kbps
AAR
MAX3373EEBL+T
Bi
2/2
AAZ
MAX3373EETA+T
Bi
2/2
AQH
MAX3374EEKA+T
Uni
2/0
AALH
MAX3374EEBL+T
Uni
2/0
ABA
MAX3374EETA+T
Uni
2/0
MAX3375EEKA+T
Uni
1/1
MAX3375EEBL+T
Uni
1/1
ABB
MAX3375EETA+T
Uni
1/1
AQJ
MAX3376EEKA+T
Uni
0/2
AALG
MAX3376EEBL+T
Uni
0/2
AAV
MAX3376EETA+T
Uni
0/2
AQK
MAX3377EEUD
Bi
4/4
MAX3377EEBC+T
Bi
4/4
MAX3377EETD+T
Bi
4/4
AAG
MAX3378EEUD
Bi
4/4
—
MAX3378EEBC+T
Bi
4/4
AAY
MAX3378EETD+T
Bi
4/4
AAH
MAX3379EEUD
Uni
4/0
—
MAX3379EEBC+T
Uni
4/0
AAZ
MAX3379EETD+T
Uni
4/0
AAI
MAX3390EEUD
Uni
3/1
—
MAX3390EEBC+T
Uni
3/1
ABA
MAX3390EETD+T
Uni
3/1
AAJ
MAX3391EEUD
Uni
2/2
MAX3391EEBC+T
Uni
2/2
ABB
MAX3391EETD+T
Uni
2/2
AAK
MAX3392EEUD
Uni
1/3
—
MAX3392EEBC+T
Uni
1/3
ABC
MAX3392EETD+T
Uni
1/3
AAL
MAX3393EEUD
Uni
0/4
—
MAX3393EEBC+T
Uni
0/4
ABD
MAX3393EETD+T
Uni
0/4
AAM
8Mbps*
AQI
AALI
—
230kbps
8Mbps*
PINPACKAGE
—
8 TDFN-EP**
(3mm x 3mm)
8 TDFN-EP**
(3mm x 3mm)
+Denotes a lead-free package.
**EP = Exposed pad.
T = Tape and reel.
Tx = VL → VCC, Rx = VCC → VL
†
*Higher data rates are possible (see the Timing Characteristics
table).
20
______________________________________________________________________________________
PKG
CODE
B9-2
T833-2
K8S-3
B9-2
T833-2
K8S-3
B9-2
T833-2
K8S-3
B9-2
T833-2
K8S-3
B9-2
T833-2
U14-1
B12-1
T1433-2
U14-1
B12-1
T1433-2
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
TEMP
RANGE
PART
MAX3379EEUD
†
†
MAX3379EEBC+T
†
MAX3379EETD+T
MAX3390EEUD
†
PINPACKAGE
U14-1
12 UCSP
-40°C to +85°C
(1.5mm x 2.0mm)
B12-1
14 TDFN-EP**
(3mm x 3mm)
-40°C to +85°C 14 TSSOP
MAX3390EEBC+T
-40°C to +85°C
12 UCSP
(1.5mm x 2.0mm)
MAX3390EETD+T
-40°C to +85°C
14 TDFN-EP**
(3mm x 3mm)
†
MAX3391EEUD
†
-40°C to +85°C 14 TSSOP
MAX3391EEBC+T
-40°C to +85°C
12 UCSP
(1.5mm x 2.0mm)
MAX3391EETD+T
-40°C to +85°C
14 TDFN-EP**
(3mm x 3mm)
†
†
PKG
CODE
-40°C to +85°C 14 TSSOP
-40°C to +85°C
T1433-2
U14-1
B12-1
T1433-2
U14-1
B12-1
T1433-2
-40°C to +85°C 14 TSSOP
U14-1
MAX3392EEBC+T
12 UCSP
-40°C to +85°C
(1.5mm x 2.0mm)
B12-1
MAX3392EETD+T
-40°C to +85°C
MAX3392EEUD
†
MAX3393EEUD
†
†
MAX3393EEBC+T
†
MAX3393EETD+T
14 TDFN-EP**
(3mm x 3mm)
T1433-2
-40°C to +85°C 14 TSSOP
U14-1
12 UCSP
-40°C to +85°C
(1.5mm x 2.0mm)
B12-1
-40°C to +85°C
14 TDFN-EP**
(3mm x 3mm)
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Ordering Information (continued)
T1433-2
+Denotes a lead-free package.
**EP = Exposed pad.
T = Tape and reel.
†
Future product—contact factory for availability.
______________________________________________________________________________________
21
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Pin Configurations (continued)
A
B
C
VCC
THREE-STATE
VL
I/O VCC2 1
1
MAX3372E
MAX3373E
2
I/O VCC1
N.C.
I/O VL1
8 I/O VCC1
GND 2
VL
7 VCC
3
6 THREE-STATE
I/O VL2 4
3
I/O VCC2
GND
5 I/O VL1
I/O VCC2 1
GND 2
I/O VCC1
3
VCC 4
8 I/O VL2
7 VL
6 I/O VL1
5 THREE-STATE
I/O VL2
SOT23-8
TOP VIEW
9 UCSP (1.5mm x 1.5mm)
BOTTOM VIEW
A
B
C
VCC
THREE-STATE
VL
O VCC1
N.C.
I VL1
O VCC2 1
1
MAX3374E
2
8 O VCC1
GND 2
VL
TDFN-8 (3mm x 3mm)
TOP VIEW
7 VCC
3
6 THREE-STATE
I V L2 4
5 I VL1
O VCC2 1
GND 2
O VCC1
3
VCC 4
8 I VL2
7 VL
6 I V L1
5 THREE-STATE
3
O VCC2
GND
I VL2
TDFN-8 (3mm x 3mm)
TOP VIEW
SOT23-8
TOP VIEW
9 UCSP (1.5mm x 1.5mm)
BOTTOM VIEW
A
B
C
O VCC2 1
1
VCC
THREE-STATE
VL
O VCC1
N.C.
I V L1
MAX3375E
2
8 I VCC1
GND 2
VL
7 VCC
3
6 THREE-STATE
I V L2 4
5 O VL1
O VCC2 1
GND 2
I VCC1
3
VCC 4
8 I VL2
7 VL
6 O V L1
5 THREE-STATE
3
I VCC2
GND
O VL2
TDFN-8 (3mm x 3mm)
TOP VIEW
SOT23-8
TOP VIEW
9 UCSP (1.5mm x 1.5mm)
BOTTOM VIEW
A
B
C
I VCC2 1
1
VCC
THREE-STATE
VL
I VCC1
N.C.
O VL1
2
GND 2
VL
7 VCC
3
6 THREE-STATE
O V L2 4
3
I VCC2
GND
5 O VL1
I VCC2 1
GND 2
I VCC1
3
VCC 4
8 O V L2
7 VL
6 O V L1
5 THREE-STATE
O VL2
9 UCSP (1.5mm x 1.5mm)
BOTTOM VIEW
22
MAX3376E
8 I VCC1
SOT23-8
TOP VIEW
TDFN-8 (3mm x 3mm)
TOP VIEW
______________________________________________________________________________________
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
A
B
C
I/O VL1
VCC
I/O VCC1
1
MAX3377E
MAX3378E
2
I/O VL2
VL
I/O VCC2
3
I/O VL3 THREE-STATE I/O VCC3
VL
1
14
VCC
I/O VL1
1
14
VCC
I/O VL1
2
13
I/0 VCC1
I/O VL2
2
13
I/0 VCC1
I/O VL2
3
12
I/0 VCC2
THREE-STATE
3
12
I/0 VCC2
I/O VL3
4
11
I/0 VCC3
N.C.
4
11
N.C.
I/O VL4
5
10
I/0 VCC4
I/O VL3
5
10
VL
N.C.
6
9
N.C.
I/O VL4
6
9
I/0 VCC3
8
I/0 VCC4
GND
4
I/O VL4
GND
B
VCC
O VCC1
MAX3379E
2
I VL2
VL
O VCC2
3
I VL3
THREE-STATE O VCC3
4
I VL4
GND
B
VCC
1
14 VCC
I VL1
1
14
VCC
I VL1
2
13 O VCC1
I VL2
2
13
0 VCC1
12
0 VCC2
I VL2
3
12 O VCC2
THREE-STATE
3
I VL3
4
11 O VCC3
N.C.
4
11
N.C.
I VL4
5
10 O VCC4
I VL3
5
10
VL
6
9
0 VCC3
7
8
0 VCC4
N.C.
6
9
N.C.
I VL4
GND
7
8
THREE-STATE
GND
C
I VCC1
2
VL
O VCC2
3
I VL3
THREE-STATE O VCC3
4
I VL4
GND
TDFN-14 (3mm x 3mm)
TOP VIEW
TSSOP-14
TOP VIEW
MAX3390E
I VL2
TDFN-14 (3mm x 3mm)
TOP VIEW
O VCC4
1
O VL1
7
VL
12 UCSP (1.5mm x 2.0mm)
BOTTOM VIEW
A
GND
C
1
I VL1
THREE-STATE
TSSOP-14
TOP VIEW
12 UCSP (1.5mm x 2.0mm)
BOTTOM VIEW
A
8
7
I/O VCC4
VL
1
14 VCC
O VL1
2
13 I VCC1
I VL2
3
12 O VCC2
I VL3
4
11 O VCC3
I VL4
5
N.C.
6
GND
7
O VL1
1
14
VCC
I VL2
2
13
I VCC1
THREE-STATE
3
12
0 VCC2
N.C.
4
11
N.C.
10 O VCC4
I VL3
5
10
VL
9
N.C.
I VL4
6
9
0 VCC3
8
THREE-STATE
GND
7
8
0 VCC4
O VCC4
12 UCSP (1.5mm x 2.0mm)
BOTTOM VIEW
TSSOP-14
TOP VIEW
TDFN-14 (3mm x 3mm)
TOP VIEW
______________________________________________________________________________________
23
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Pin Configurations (continued)
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Pin Configurations (continued)
A
B
C
O VL1
VCC
I VCC1
14 VCC
O VL1
1
14
VCC
O VL1
2
13 I VCC1
O VL2
2
13
I VCC1
O VL2
3
12 I VCC2
THREE-STATE
3
12
I VCC2
VL 1
1
MAX3391E
2
O VL2
VL
I VCC2
3
I VL3
THREE-STATE O VCC3
I VL3 4
11 O VCC3
N.C.
4
11
N.C.
I V L4 5
10 O VCC4
I VL3
5
10
VL
N.C. 6
9
N.C.
I VL4
6
9
0 VCC3
THREE-STATE
GND
7
8
0 VCC4
GND 7
4
I VL4
GND
A
B
C
O VL1
VCC
I VCC1
VL 1
1
MAX3392E
2
O VL2
VL
I VCC2
3
O VL3
THREE-STATE I VCC3
GND
B
I VCC1
I VCC2
3
O VL3 THREE-STATE I VCC3
O VL2
3
12 I VCC2
THREE-STATE
3
12
I VCC2
O VL3 4
11 I VCC3
N.C.
4
11
N.C.
I VL 4 5
10 O VCC4
O VL3
5
10
VL
N.C. 6
9
I VL4
6
9
I VCC3
8
0 VCC4
8
GND
N.C.
THREE-STATE
GND
7
TDFN-14 (3mm x 3mm)
TOP VIEW
14 VCC
O VL1
1
14
VCC
O VL1
2
13 I VCC1
O VL2
2
13
I VCC1
O VL2
3
12 I VCC2
THREE-STATE
3
12
I VCC2
O VL3 4
11 I VCC3
N.C.
4
11
N.C.
O V L4 5
10 I VCC4
O VL3
5
10
VL
9
O VL4
6
9
I VCC3
8
I VCC4
N.C. 6
GND 7
4
O VL4
I VCC1
13 I VCC1
TSSOP-14
TOP VIEW
MAX3393E
VL
VCC
13
C
2
O VL2
14
2
2
VL 1
VCC
1
O VCC4
1
O VL1
O VL1
O VL1
12 UCSP (1.5mm x 2.0mm)
BOTTOM VIEW
A
14 VCC
O VL2
GND 7
4
I V L4
TDFN-14 (3mm x 3mm)
TOP VIEW
TSSOP-14
TOP VIEW
12 UCSP (1.5mm x 2.0mm)
BOTTOM VIEW
8
N.C.
THREE-STATE
GND
7
I VCC4
12 UCSP (1.5mm x 2.0mm)
BOTTOM VIEW
24
8
O VCC4
TSSOP-14
TOP VIEW
TDFN-14 (3mm x 3mm)
TOP VIEW
______________________________________________________________________________________
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
SOT23, 8L.EPS
MARKING
0
0
PACKAGE OUTLINE, SOT-23, 8L BODY
21-0078
G
1
1
Chip Information
TRANSISTOR COUNT: MAX3372E–MAX3376E: 189
MAX3377E–MAX3379E,
MAX3390E–MAX3393E: 295
PROCESS: BiCMOS
______________________________________________________________________________________
25
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
6, 8, &10L, DFN THIN.EPS
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
26
______________________________________________________________________________________
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
COMMON DIMENSIONS
PACKAGE VARIATIONS
SYMBOL
MIN.
MAX.
PKG. CODE
N
D2
E2
e
JEDEC SPEC
b
[(N/2)-1] x e
A
0.70
0.80
T633-2
6
1.50±0.10
2.30±0.10
0.95 BSC
MO229 / WEEA
0.40±0.05
1.90 REF
D
2.90
3.10
T833-2
8
1.50±0.10
2.30±0.10
0.65 BSC
MO229 / WEEC
0.30±0.05
1.95 REF
E
2.90
3.10
T833-3
8
1.50±0.10
2.30±0.10
0.65 BSC
MO229 / WEEC
0.30±0.05
1.95 REF
A1
0.00
0.05
T1033-1
10
1.50±0.10
2.30±0.10
0.50 BSC
MO229 / WEED-3
0.25±0.05
2.00 REF
L
0.20
0.40
T1033-2
10
1.50±0.10
2.30±0.10
0.50 BSC
MO229 / WEED-3
0.25±0.05
2.00 REF
k
0.25 MIN.
T1433-1
14
1.70±0.10
2.30±0.10
0.40 BSC
----
0.20±0.05
2.40 REF
A2
0.20 REF.
T1433-2
14
1.70±0.10
2.30±0.10
0.40 BSC
----
0.20±0.05
2.40 REF
______________________________________________________________________________________
27
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066
28
______________________________________________________________________________________
I
1
1
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
9LUCSP, 3x3.EPS
PACKAGE OUTLINE, 3x3 UCSP
21-0093
L
1
1
______________________________________________________________________________________
29
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
12L, UCSP 4x3.EPS
MAX3372E–MAX3379E/MAX3390E–MAX3393E
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
PACKAGE OUTLINE, 4x3 UCSP
21-0104
30
______________________________________________________________________________________
F
1
1
±15kV ESD-Protected, 1µA, 16Mbps, Dual/Quad
Low-Voltage Level Translators in UCSP
REVISION
NUMBER
REVISION
DATE
DESCRIPTION
0
1/02
Initial Release
1
12/06
Addition of 12-bump ECSP packaging
2
11/07
Addition of lead-free options
PAGES
CHANGED
—
–
1, 20–31
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 31
© 2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
MAX3372E–MAX3379E/MAX3390E–MAX3393E
Revision History