MAXIM MAX3005EUP

19-2672; Rev 5; 8/08
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
The MAX3000E/MAX3001E/MAX3002–MAX3012
8-channel level translators provide the level shifting necessary to allow data transfer in a multivoltage system.
Externally applied voltages, VCC and VL, set the logic levels on either side of the device. Logic signals present on
the VL side of the device appear as a higher voltage logic
signal on the VCC side of the device, and vice-versa.
The MAX3000E/MAX3001E/MAX3002/MAX3003 use an
architecture specifically designed to be bidirectional
without the use of a directional pin.
The MAX3000E/MAX3001E/MAX3002/MAX3004–MAX3012
feature an EN input that, when low, reduces the VCC and
VL supply currents to < 2µA. The MAX3000E/MAX3001E
also have ±15kV ESD protection on the I/O VCC side for
greater protection in applications that route signals
externally. The MAX3000E operates at a guaranteed data
rate of 230kbps. The MAX3001E operates at a guaranteed
data rate of 4Mbps. The MAX3002–MAX3012 operate at a
guaranteed data rate of 20Mbps over the entire specified
operating voltage range.
The MAX3000E/MAX3001E/MAX3002–MAX3012 accept
VL voltages from +1.2V to +5.5V and VCC voltages from
+1.65V to +5.5V, making them ideal for data transfer
between low-voltage ASICs/PLDs and higher voltage
systems. The MAX3000E/MAX3001E/MAX3002–
MAX3012 are available in 20-bump UCSP™, 20-pin
TQFN (5mm x 5mm), and 20-pin TSSOP packages.
Features
♦ Guaranteed Data Rate Options
230kbps (MAX3000E)
4Mbps (MAX3001E)
20Mbps (MAX3002–MAX3012)
♦ Bidirectional Level Translation Without Using a
Directional Pin (MAX3000E/MAX3001E/MAX3002/
MAX3003)
♦ Unidirectional Level Translation
(MAX3004–MAX3012)
♦ Operation Down to +1.2V on VL
♦ ±15kV ESD Protection on I/O VCC Lines
(MAX3000E/MAX3001E)
♦ Ultra-Low 0.1µA Supply Current in Shutdown
♦ Low Quiescent Current (< 10µA)
♦ UCSP, TQFN, and TSSOP Packages
Ordering Information
TEMP RANGE
PIN-PACKAGE
MAX3000EEUP
PART
-40°C to +85°C
20 TSSOP
MAX3000EEBP-T
-40°C to +85°C
4 x 5 UCSP
Ordering Information continued at end of data sheet.
Note: All devices operate over the -40°C to +85°C operating
temperature range.
Typical Operating Circuit
Applications
CMOS Logic-Level Translation
+1.8V
+3.3V
Cellphones
SPI™ and MICROWIRE™ Level Translation
Low-Voltage ASIC Level Translation
Smart Card Readers
Portable POS Systems
Portable Communication Devices
Low-Cost Serial Interfaces
VCC
VL
Cellphone Cradles
EN
+1.8V
SYSTEM
CONTROLLER
MAX3000E
MAX3001E
MAX3002–
MAX3012
+3.3V
SYSTEM
GPS
DATA
Telecommunications Equipment
UCSP is a trademark of Maxim Integrated Products, Inc.
I/O VL_
I/O VCC_
DATA
GND
SPI is a trademark of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor.
Pin Configurations and Functional Diagrams appear at end
of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX3000E/MAX3001E/MAX3002–MAX3012
General Description
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND.)
VCC ...........................................................................-0.3V to +6V
VL...........................................................................................-0.3V to +6V
I/O VCC_......................................................-0.3V to (VCC + 0.3V)
I/O VL_ ...........................................................-0.3V to (VL + 0.3V)
EN, EN A/B ...............................................................-0.3V to +6V
Short-Circuit Duration I/O VL_, I/O VCC_ to GND .......Continuous
Continuous Power Dissipation (TA = +70°C)
20-Pin TSSOP (derate 7.0mW/°C above +70°C) .........559mW
20-Bump UCSP (derate 10mW/°C above +70°C) .......800mW
20-Pin 5mm x 5mm TQFN
(derate 20.0mW/°C above +70°C) .....................................1667mW
Operating Temperature Ranges
MAX3001EAUP ..............................................-40°C to +125°C
MAX300_EE_P .................................................-40°C to +85°C
MAX30_ _E_P ..................................................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +1.65V to +5.5V, VL = +1.2V to VCC, EN = VL (MAX3000E/MAX3001E/MAX3002/MAX3004–MAX3012), EN A/B = VL or 0
(MAX3003), TA = TMIN to TMAX. Typical values are at VCC = +1.65V, VL = +1.2V, and TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
POWER SUPPLIES
VL Supply Range
VCC Supply Range
VL
1.2
VCC
V
VCC
1.65
5.50
V
I/O VCC_ = 0, I/O VL _ = 0
or I/O VCC_ = VCC, I/O VL _ = VL,
MAX3000E/MAX3002–MAX3012
Supply Current from VCC
Supply Current from VL
VL Shutdown Supply Current
2
10
µA
IQVCC
I/O VCC_ = 0, I/O VL _ = 0
or I/O VCC_ = VCC, I/O VL _ = VL,
MAX3001E
0.1
50
I/O VCC_ = 0, I/O VL _ = 0
or I/O VCC_ = VCC, I/O VL _ = VL,
MAX3000E/MAX3002–MAX3012
0.1
10
µA
IQVL
I/O VCC_ = 0, I/O VL _ = 0
or I/O VCC_ = VCC, I/O VL _ = VL,
MAX3001E
VCC Shutdown Supply Current
0.1
TA = +25°C, EN = 0,
MAX3000E/MAX3001E/MAX3002/
ISHDN-VCC MAX3004–MAX3012
ISHDN-VL
0.1
50
0.1
2
µA
TA = +25°C, EN A/B = 0,
MAX3003
0.1
2
TA = +25°C, EN = 0,
MAX3000E/MAX3001E/MAX3002/
MAX3004–MAX3012
0.1
2
TA = +25°C, EN A/B = 0,
MAX3003
0.1
µA
_______________________________________________________________________________________
2
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
(VCC = +1.65V to +5.5V, VL = +1.2V to VCC, EN = VL (MAX3000E/MAX3001E/MAX3002/MAX3004–MAX3012), EN A/B = VL or 0
(MAX3003), TA = TMIN to TMAX. Typical values are at VCC = +1.65V, VL = +1.2V, and TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
TYP
MAX
TA = +25°C, EN = 0,
MAX3000E/MAX3001E/MAX3002/
MAX3004–MAX3012
0.1
2
TA = +25°C, EN A/B = 0,
MAX3003
0.1
2
I/O VL _ Three-State Output
Leakage Current
EN A/B = 0, MAX3003
0.1
2
µA
I/O VL _ Pulldown Resistance
During Shutdown
EN = 0,
MAX3000E/MAX3001E/MAX3002/
MAX3004–MAX3012
8.30
kΩ
EN or EN A/B Input Leakage Current
TA = +25°C
1
µA
2/3 x VL
V
I/O VCC _ Three-State Output
Leakage Current
CONDITIONS
MIN
UNITS
µA
4.59
LOGIC-LEVEL THRESHOLDS
I/O VL _ Input-Voltage High
Threshold
VIHL
I/O VL _ Input-Voltage Low
Threshold
VILL
I/O VCC _ Input-Voltage High
Threshold
VIHC
I/O VCC _ Input-Voltage Low
Threshold
VILC
EN, EN A/B Input-Voltage High
Threshold
VIH
EN, EN A/B Input-Voltage Low
Threshold
VIL
1/3 x VL
V
2/3 x VCC
1/3 x VCC
V
VL - 0.4
I/O VL _ Output-Voltage High
VOHL
I/O VL _ source current = 20µA, I/O VCC _ ≥
VCC - 0.4V
I/O VL _ Output-Voltage Low
VOLL
I/O VL _ sink current = 20µA,
I/O VCC _ ≤ 0.4V
I/O VCC _ Output-Voltage High
VOHC
I/O VCC_ source current = 20µA, I/O VL _ ≥
VL - 0.4V
I/O VCC _ Output-Voltage Low
VOLC
I/O VCC sink current = 20µA,
I/O VL _ ≤ 0.4V
V
V
0.4
V
VL - 0.4
V
0.4
VCC - 0.4
V
V
0.4
V
ESD PROTECTION
I/O VCC _
Human Body Model,
MAX3000E/MAX3001E
±15
kV
_______________________________________________________________________________________
3
MAX3000E/MAX3001E/MAX3002–MAX3012
ELECTRICAL CHARACTERISTICS (continued)
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
TIMING CHARACTERISTICS
(VCC = +1.65V to +5.5V, VL = +1.2V to VCC, EN = VL (MAX3000E/MAX3001E/MAX3002/MAX3004–MAX3012), EN A/B = VL or 0
(MAX3003), TA = TMIN to TMAX. Typical values are at VCC = +1.65V, VL = +1.2V, and TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
RS = 50Ω, CVCC = 50pF, MAX3000E,
Figures 1a, 1b
I/O VCC_ Rise Time
tRVCC
MIN
TYP
MAX
400
800
1200
25
50
RS = 50Ω, CVCC = 50pF, MAX3001E,
Figures 1a, 1b
RS = 50Ω, CVCC = 50pF,
MAX3002–MAX3012, Figures 1a, 1b
RS = 50Ω, CVCC = 50pF, MAX3000E,
Figures 1a, 1b
I/O VCC_ Fall Time
tFVCC
400
800
1200
25
50
RS = 50Ω, CVCC = 50pF,
MAX3002–MAX3012, Figures 1a, 1b
I/O VL _ Rise Time
tRVL
400
800
1200
25
50
RS = 50Ω, CVL = 15pF,
MAX3002–MAX3012, Figures 2a, 2b
I/O VL _ Fall Time
Propagation Delay
(Driving I/O VL _)
Propagation Delay
(Driving I/O VCC_)
tFVL
I/OVL-VCC
I/OVCC-VL
RS = 50Ω, CVL = 50pF, MAX3001E,
Figures 2a, 2b
ns
15
RS = 50Ω, CVL = 50pF, MAX3001E,
Figures 2a, 2b
RS = 50Ω, CVL = 50pF, MAX3000E,
Figures 2a, 2b
ns
15
RS = 50Ω, CVCC = 50pF, MAX3001E,
Figures 1a, 1b
RS = 50Ω, CVL = 50pF, MAX3000E,
Figures 2a, 2b
UNITS
ns
15
400
800
1200
25
65
RS = 50Ω, CVL = 15pF,
MAX3002–MAX3012, Figures 2a, 2b
15
RS = 50Ω, CVCC = 50pF, MAX3000E,
Figures 1a, 1b
1000
RS = 50Ω, CVCC = 50pF, MAX3001E,
Figures 1a, 1b
50
RS = 50Ω, CVCC = 50pF,
MAX3002–MAX3012, Figures 1a, 1b
20
RS = 50Ω, CVL = 50pF, MAX3000E,
Figures 2a, 2b
1000
RS = 50Ω, CVL = 50pF, MAX3001E,
Figures 2a, 2b
50
RS = 50Ω, CVL = 15pF,
MAX3002–MAX3012, Figures 2a, 2b
20
ns
ns
ns
Note 1: All units are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed by design
and not production tested.
Note 2: For normal operation, ensure that VL < VCC. During power-up, VL > VCC does not damage the device.
4
_______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
(VCC = +1.65V to +5.5V, VL = +1.2V to VCC, EN = VL (MAX3000E/MAX3001E/MAX3002/MAX3004–MAX3012), EN A/B = VL or 0
(MAX3003), TA = TMIN to TMAX. Typical values are at VCC = +1.65V, VL = +1.2V, and TA = +25°C.) (Notes 1, 2)
PARAMETER
Channel-to-Channel Skew
Part-to-Part Skew
SYMBOL
tSKEW
tPPSKEW
Propagation Delay from
I/O VL _ to I/O VCC_ after EN
tEN-VCC
Propagation Delay from
I/O VCC_ to I/O VL _ after EN
tEN-VL
Maximum Data Rate
CONDITIONS
MIN
TYP
MAX
RS = 50Ω, CVCC = 50pF, CVL = 50pF,
MAX3000E
500
RS = 50Ω, CVCC = 50pF, CVL = 50pF,
MAX3001E
10
RS = 50Ω, CVCC = 50pF, CVL = 15pF,
MAX3002–MAX3012
5
RS = 50Ω, CVCC = 50pF, CVL = 50pF,
ΔTA = +20°C, MAX3000E (Note 3)
800
RS = 50Ω, CVCC = 50pF, CVL = 50pF,
ΔTA = +20°C, MAX3001E (Note 3)
30
RS = 50Ω, CVCC = 50pF, CVL = 15pF,
ΔTA = +20°C, MAX3002–MAX3012 (Note 3)
10
CVCC = 50pF, MAX3000E/MAX3001E,
MAX3002–MAX3012, Figure 3
2
CVL = 50pF, MAX3000E/MAX3001E/
MAX3002/MAX3004–MAX3012, Figure 4
2
CVL = 15pF, MAX3003, Figure 4
2
RS = 50Ω, CVCC = 50pF, CVL = 50pF,
MAX3000E
230
RS = 50Ω, CVCC = 50pF, CVL = 50pF,
MAX3001E
4
UNITS
ns
ns
µs
µs
kbps
Mbps
RS = 50Ω, CVCC = 50pF, CVL = 15pF,
MAX3002–MAX3012
20
Note 3: VCC from device 1 must equal VCC of device 2; VL from device 1 must equal VL of device 2.
_______________________________________________________________________________________
5
MAX3000E/MAX3001E/MAX3002–MAX3012
TIMING CHARACTERISTICS (continued)
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
TIMING CHARACTERISTICS—MAX3002–MAX3012
(VCC = +1.65V to +5.5V, VL = +1.2V to VCC, EN = VL (MAX3002/MAX3004–MAX3012), EN A/B = VL or 0 (MAX3003), TA = TMIN to
TMAX.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
+1.2V ≤ VL ≤ VCC ≤ +3.3V
I/O VCC_ Rise Time
tRVCC
15
ns
I/O VCC_ Fall Time
tFVCC
15
ns
I/O VL _ Rise Time
tRVL
15
ns
I/O VL _ Fall Time
tFVL
15
ns
Propagation Delay
Channel-to-Channel Skew
I/OVL-VCC
Driving I/O VL _
15
I/OVCC-VL
Driving I/O VCC_
Each translator equally loaded
15
tSKEW
Maximum Data Rate
5
20
ns
ns
Mbps
+2.5V ≤ VL ≤ VCC ≤ +3.3V
I/O VCC_ Rise Time
tRVCC
8.5
ns
I/O VCC_ Fall Time
tFVCC
8.5
ns
I/O VL _ Rise Time
tRVL
8.5
ns
I/O VL _ Fall Time
tFVL
8.5
ns
Propagation Delay
Channel-to-Channel Skew
I/OVL-VCC
Driving I/O VL _
8.5
I/OVCC-VL
Driving I/O VCC_
8.5
Each translator equally loaded
10
tSKEW
Maximum Data Rate
35
ns
ns
Mbps
+1.8V ≤ VL ≤ VCC ≤ +2.5V
I/O VCC_ Rise Time
tRVCC
10
ns
I/O VCC_ Fall Time
tFVCC
10
ns
I/O VL _ Rise Time
tRVL
10
ns
I/O VL _ Fall Time
tFVL
10
ns
Propagation Delay
Channel-to-Channel Skew
Maximum Data Rate
6
I/OVL-VCC
Driving I/O VL _
15
I/OVCC-VL
Driving I/O VCC_
10
Each translator equally loaded
5
tSKEW
30
_______________________________________________________________________________________
ns
ns
Mbps
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
VCC SUPPLY CURRENT vs. SUPPLY VOLTAGE
(DRIVING I/O VL, VL = 1.8V)
300
DATA RATE = 4Mbps
6000
DATA RATE = 4Mbps
4000
DATA RATE = 230kbps
2000
DATA RATE = 230kbps
0
0
3.0
3.5
4.0
4.5
5.0
5.5
2.0
2.5
SUPPLY VOLTAGE (V)
3.0
3.5
4.0
4.5
DATA RATE = 4Mbps
DATA RATE = 230kbps
500
5.0
5.5
-40
-15
DATA RATE = 20Mbps
1500
DATA RATE = 4Mbps
DATA RATE = 230kbps
10
35
60
85
TEMPERATURE (°C)
VL SUPPLY CURRENT vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
100
VL SUPPLY CURRENT (μA)
MAX3000E/01E/02-12 toc04
2500
2000
MAX3000E/01E/02-12 toc03
1000
SUPPLY VOLTAGE (V)
VCC SUPPLY CURRENT vs. TEMPERATURE
(DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
1000
DATA RATE = 20Mbps
0
1.5
80
DATA RATE = 20Mbps
60
DATA RATE = 4Mbps
40
500
20
0
0
DATA RATE = 230kbps
-40
-15
10
35
60
10
85
20
30
7000
6000
DATA RATE = 20Mbps
4000
3000
DATA RATE = 4Mbps
2000
50
60
70
80
90 100
MAX3000E
RISE/FALL TIME vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
VCC SUPPLY CURRENT vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
5000
40
CAPACITIVE LOAD (pF)
TEMPERATURE (°C)
DATA RATE = 230kbps
2000
RISE/FALL TIME (ns)
2.5
MAX3000E/01E/02-12 toc06
2.0
VCC SUPPLY CURRENT (μA)
1.5
1500
MAX3000E/01E/02-12 toc05
100
8000
2000
1500
MAX3000E/01E/02-12 toc07
200
MAX3000E/01E/02-12 toc02
400
DATA RATE = 20Mbps
VCC SUPPLY CURRENT (μA)
DATA RATE = 20Mbps
VCC SUPPLY CURRENT (μA)
VL SUPPLY CURRENT (μA)
500
10,000
MAX3000E/01E/02-12 toc01
600
VL SUPPLY CURRENT vs. TEMPERATURE
(DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
VL SUPPLY CURRENT (μA)
VL SUPPLY CURRENT vs. SUPPLY VOLTAGE
(DRIVING I/O VL, VL = 1.8V)
tLH
1000
tHL
500
1000
DATA RATE = 230kbps
0
0
10
20
30
40
50
60
70
CAPACITIVE LOAD (pF)
80
90 100
10
20
30
40
50
60
70
80
90 100
CAPACITIVE LOAD (pF)
_______________________________________________________________________________________
7
MAX3000E/MAX3001E/MAX3002–MAX3012
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
MAX3002–MAX3012
RISE/FALL TIME vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
MAX3001E
RISE/FALL TIME vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
tLH
40
30
tHL
20
MAX3000E/01E/02-12 toc09
RISE/FALL TIME (ns)
50
8
6
RISE/FALL TIME (ns)
MAX3000E/01E/02-12 toc08
60
tLH
4
tHL
2
10
DATA RATE = 20Mbps
DATA RATE = 4Mbps
0
0
20
30
40
50
60
70
80
10
90 100
20
MAX3000E/01E/02-12 toc10
2000
tLH
RISE/FALL TIME (ns)
40
50
1500
tHL
MAX3001E
RISE/FALL TIME vs. CAPACITIVE LOAD ON
I/O VL (DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
60
50
tHL
RISE/FALL TIME (ns)
MAX3000E
RISE/FALL TIME vs. CAPACITIVE LOAD ON
I/O VL (DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
1000
30
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
MAX3000E/01E/02-12 toc11
10
40
30
tLH
20
500
10
DATA RATE = 4Mbps
DATA RATE = 230kbps
0
0
20
30
40
60
50
70
80
90 100
10
20
30
MAX3000E/01E/02-12 toc12
4
tHL
2
1
50
tLH
70
80
90 100
500
400
tPLH
300
tPHL
200
100
DATA RATE = 20Mbps
DATA RATE = 230kbps
0
0
10
15
20
25
CAPACITIVE LOAD (pF)
8
60
MAX3000E
PROPAGATION DELAY vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
PROPAGATION DELAY (ns)
MAX3002–MAX3012
RISE/FALL TIME vs. CAPACITIVE LOAD ON
I/O VL (DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
3
40
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
MAX3000E/01E/02-12 toc13
10
RISE/FALL TIME (ns)
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
30
10
20
30
40
50
60
70
80
CAPACITIVE LOAD (pF)
_______________________________________________________________________________________
90 100
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
tPHL
6
4
tPHL
2
5
400
200
100
DATA RATE = 230kbps
0
10
20
30
40
tPLH
300
DATA RATE = 20Mbps
DATA RATE = 4Mbps
0
0
10
50
MAX3000E/01E/02-12 toc16
tPLH
8
tPHL
500
15
20
25
30
10
20
30
40
CAPACITIVE LOAD (pF)
CAPACITIVE LOAD (pF)
MAX3001E
PROPAGATION DELAY vs. CAPACITIVE LOAD ON
I/O VL (DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
5
tPHL
PROPAGATION DELAY (ns)
12
60
70
80
90 100
MAX3002–MAX3012
PROPAGATION DELAY vs. CAPACITIVE LOAD ON
I/O VL (DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
MAX3000E/01E/02-12 toc17
15
50
CAPACITIVE LOAD (pF)
9
6
tPLH
3
MAX3000E/01E/02-12 toc18
10
600
PROPAGATION DELAY (ns)
15
10
MAX3000E
PROPAGATION DELAY vs. CAPACITIVE LOAD ON
I/O VL (DRIVING I/O VCC, VCC = 3.3V, VL = 1.8V)
MAX3000E/01E/02-12 toc15
tPLH
20
PROPAGATION DELAY (ns)
PROPAGATION DELAY (ns)
25
12
PROPAGATION DELAY (ns)
MAX3000E/01E/02-12 toc14
30
MAX3002–MAX3012
PROPAGATION DELAY vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
4
tPHL
3
2
tPLH
1
DATA RATE = 4Mbps
DATA RATE = 20Mbps
0
0
10
20
30
40
50
10
15
CAPACITIVE LOAD (pF)
MAX3001E RAIL-TO-RAIL DRIVING
(DRIVING I/O VL, VCC = 3.3V, VL = 1.8V,
CVCC = 50pF, DATA RATE = 4Mbps)
MAX3000E RAIL-TO-RAIL DRIVING
(DRIVING I/O VL, VCC = 3.3V, VL = 1.8V,
CVCC = 50pF, DATA RATE = 230kbps)
25
30
MAX3002–MAX3012 RAIL-TO-RAIL DRIVING
(DRIVING I/O VL, VCC = 3.3V, VL = 1.8V,
CVCC = 50pF, DATA RATE = 20Mbps)
MAX3000E/01E/02-12 toc20
MAX3000E/01E/02-12 toc19
1μs/div
20
CAPACITIVE LOAD (pF)
MAX3000E/01E/02-12 toc21
MAX3000E/MAX3001E/MAX3002–MAX3012
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
MAX3001E
PROPAGATION DELAY vs. CAPACITIVE LOAD ON
I/O VCC (DRIVING I/O VL, VCC = 3.3V, VL = 1.8V)
I/O VL_
1V/div
I/O VL_
1V/div
I/O VL_
1V/div
GND
GND
GND
I/O VCC_
2V/div
I/O VCC_
2V/div
I/O VCC_
2V/div
GND
GND
GND
40ns/div
10ns/div
_______________________________________________________________________________________
9
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
Pin Description
MAX3000E/MAX3001E/MAX3002
PIN
NAME
FUNCTION
TSSOP
UCSP
TQFN
1
B1
19
I/O VL1
2
A1
20
VL
3
A2
1
I/O VL2
Input/Output 2, Referenced to VL
4
B2
2
I/O VL3
Input/Output 3, Referenced to VL
5
A3
3
I/O VL4
Input/Output 4, Referenced to VL
6
B3
4
I/O VL5
Input/Output 5, Referenced to VL
7
A4
5
I/O VL6
Input/Output 6, Referenced to VL
8
B4
6
I/O VL7
Input/Output 7, Referenced to VL
9
A5
7
I/O VL8
Input/Output 8, Referenced to VL
10
B5
8
EN
11
C5
9
GND
12
D5
10
I/O VCC8
Input/Output 8, Referenced to VCC
13
C4
11
I/O VCC7
Input/Output 7, Referenced to VCC
14
D4
12
I/O VCC6
Input/Output 6, Referenced to VCC
15
C3
13
I/O VCC5
Input/Output 5, Referenced to VCC
16
D3
14
I/O VCC4
Input/Output 4, Referenced to VCC
17
C2
15
I/O VCC3
Input/Output 3, Referenced to VCC
18
D2
16
I/O VCC2
Input/Output 2, Referenced to VCC
19
D1
17
VCC
20
C1
18
I/O VCC1
—
—
EP
EP
10
Input/Output 1, Referenced to VL
Logic Input Voltage, +1.2V ≤ VL ≤ VCC. Bypass VL to GND with a 0.1µF capacitor.
Enable Input. If EN is pulled low, I/O VCC1 to I/O VCC8 are in three-state, while I/O VL1
to I/O VL8 have internal 6kΩ pulldown resistors. Drive EN high (VL) for normal
operation.
Ground
VCC Input Voltage, +1.65V ≤ VCC ≤ +5.5V. Bypass VCC to GND with a 0.1µF capacitor.
Input/Output 1, Referenced to VCC
Exposed Pad. Connect to GND.
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
MAX3003
PIN
NAME
FUNCTION
TSSOP
UCSP
TQFN
1
B1
19
I/O VL1A
2
A1
20
VL
3
A2
1
I/O VL2A
Input/Output 2A, Referenced to VL
4
B2
2
I/O VL3A
Input/Output 3A, Referenced to VL
5
A3
3
I/O VL4A
Input/Output 4A, Referenced to VL
6
B3
4
I/O VL1B
Input/Output 1B, Referenced to VL
7
A4
5
I/O VL2B
Input/Output 2B, Referenced to VL
8
B4
6
I/O VL3B
Input/Output 3B, Referenced to VL
9
A5
7
I/O VL4B
Input/Output 4B, Referenced to VL
10
B5
8
EN A/B
11
C5
9
GND
12
D5
10
I/O VCC4B
Input/Output 4B, Referenced to VCC
13
C4
11
I/O VCC3B
Input/Output 3B, Referenced to VCC
14
D4
12
I/O VCC2B
Input/Output 2B, Referenced to VCC
15
C3
13
I/O VCC1B
Input/Output 1B, Referenced to VCC
16
D3
14
I/O VCC4A
Input/Output 4A, Referenced to VCC
17
C2
15
I/O VCC3A
Input/Output 3A, Referenced to VCC
18
D2
16
I/O VCC2A
Input/Output 2A, Referenced to VCC
19
D1
17
VCC
20
C1
18
I/O VCC1A
—
—
EP
EP
Input/Output 1A, Referenced to VL
Logic Input Voltage, +1.2V ≤ VL ≤ VCC. Bypass VL to GND with a 0.1µF capacitor.
Enable Input. If EN A/B is pulled low, channels 1B through 4B are active, and channels
1A through 4A are in three-state. If EN A/B is driven high to VL, channels 1A through 4A
are active, and channels 1B through 4B are in three-state.
Ground
VCC Input Voltage, +1.65V ≤ VCC ≤ +5.5V. Bypass VCC to GND with a 0.1µF capacitor.
Input/Output 1A, Referenced to VCC
Exposed Pad. Connect to GND.
______________________________________________________________________________________
11
MAX3000E/MAX3001E/MAX3002–MAX3012
Pin Description (continued)
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
Pin Description (continued)
MAX3004–MAX3012
NAME
VCC
VL
GND
FUNCTION (Note 1)
VCC Input Voltage, +1.65V < VCC < +5.5V. Bypass VCC to GND with a 0.1µF capacitor.
Logic Input Voltage, +1.2V ≤ VL ≤ VCC. Bypass VL to GND with a 0.1µF capacitor.
Ground
EN
(MAX3004)
Enable Input. If EN is pulled low, OVCC1–OVCC8 are in three-state, while IVL1–IVL8 have 6kΩ pulldown
resistors. Drive EN high (VL) for normal operation.
EN
(MAX3005)
Enable Input. If EN is pulled low, IVCC1 and OVCC2–OVCC8 are in three-state, while OVL1 and IVL2–IVL8 have
6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3006)
Enable Input. If EN is pulled low, IVCC1, IVCC2, and OVCC3–OVCC8 are in three-state, while OVL1, OVL2, and
IVL3–IVL8 have 6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3007)
Enable Input. If EN is pulled low, IVCC1, IVCC2, IVCC3, and OVCC4–OVCC8 are in three-state, while OVL1,
OVL2, OVL3, and IVL4–IVL8 have 6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3008)
Enable Input. If EN is pulled low, IVCC1–IVCC4 and OVCC5–OVCC8 are in three-state, while OVL1–OVL4 and
IVL5–IVL8 have 6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3009)
Enable Input. If EN is pulled low, IVCC1–IVCC5, OVCC6, OVCC7, and OVCC8 are in three-state, while
OVL1–OVL5, IVL6, IVL7, and IVL8 have 6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3010)
Enable Input. If EN is pulled low, IVCC1–IVCC6, OVCC7, and OVCC8 are in three-state, while OVL1–OVL6, IVL7,
and IVL8 have 6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3011)
Enable Input. If EN is pulled low, IVCC1–IVCC7 and OVCC8 are in three-state, while OVL1–OVL7 and IVL8 have
6kΩ pulldown resistors. Drive EN high (VL) for normal operation.
EN
(MAX3012)
Enable Input. If EN is pulled low, IVCC1–IVCC8 are in three-state, while OVL1–OVL8 have 6kΩ pulldown
resistors. Drive EN high (VL) for normal operation.
IVL1–IVL8
Inputs Referenced to VL, Numbers 1 to 8
OVL1–OVL8
Outputs Referenced to VL, Numbers 1 to 8
IVCC1–IVCC8
Inputs Referenced to VCC, Numbers 1 to 8
OVCC1–OVCC8
Outputs Referenced to VCC, Numbers 1 to 8
Note 1: For specific pin numbers, see the Pin Configurations.
12
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
tRISE/FALL ≤ 3ns
I/O VL
VL
VCC
MAX3000E/MAX3001E/
EN
MAX3002/MAX3003
90%
50%
10%
I/OVL-VCC
I/O VL
I/OVL-VCC
I/O VCC
I/O VCC
SOURCE
RS
CVCC
90%
50%
10%
tFVCC
tRVCC
Figure 1b. Timing for Driving I/O VL
Figure 1a. Driving I/O VL
tRISE/FALL ≤ 3ns
I/O VCC
VL
90%
VCC
MAX3000E/MAX3001E/
EN
MAX3002/MAX3003
50%
10%
I/OVCC-VL
I/OVCC-VL
RS
I/O VL
CVL
I/O VCC
SOURCE
I/O VL
90%
50%
10%
tFVL
Figure 2a. Driving I/O VCC
tRVL
Figure 2b. Timing for Driving I/O VCC
______________________________________________________________________________________
13
MAX3000E/MAX3001E/MAX3002–MAX3012
______________________________________________Test Circuits/Timing Diagrams
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
_________________________________Test Circuits/Timing Diagrams (continued)
VL
EN
MAX3000E/MAX3001E/
MAX3002/MAX3003
SOURCE
EN
t'EN-VCC
VL
I/O VCC
I/O VL
0
I/O VL
0
VL
CVCC
VCC
I/O VCC
VL
EN
EN
MAX3000E/MAX3001E/
MAX3002/MAX3003
SOURCE
VCC
2
t"EN-VCC
0
VL
I/O VL
I/O VCC
I/O VL
0
VL
CVCC
VCC
I/O VCC
2
VCC
0
tEN-VCC IS WHICHEVER IS LARGER BETWEEN t'EN-VCC AND t"EN-VCC
Figure 3. Propagation Delay from I/O VL to I/O VCC After EN
VL
EN
MAX3000E/MAX3001E/
MAX3002/MAX3003
SOURCE
EN
t'EN-VL
VCC
I/O VCC
I/O VL
0
I/O VCC
0
VCC
CVL
I/O VL
VL
VL
2
0
VL
EN
SOURCE
MAX3000E/MAX3001E/
MAX3002/MAX3003
EN
t"EN-VL
0
VCC
I/O VL
CVL
I/O VCC
I/O VCC
0
VCC
I/O VL
VL
2
tEN-VL IS WHICHEVER IS LARGER BETWEEN t'EN-VL AND t"EN-VL
Figure 4. Propagation Delay from I/O VCC to I/O VL After EN
14
______________________________________________________________________________________
VL
0
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
The MAX3000E/MAX3001E/MAX3002–MAX3012 logiclevel translators provide the level shifting necessary to
allow data transfer in a multivoltage system. Externally
applied voltages, VCC and VL, set the logic levels on
either side of the device. Logic signals present on the
VL side of the device appear as a higher voltage logic
signal on the VCC side of the device, and vice-versa.
The MAX3000E/MAX3001E/MAX3002/MAX3003 are
bidirectional level translators allowing data translation in
either direction (VL ↔ VCC) on any single data line.
These devices use an architecture specifically
designed to be bidirectional without the use of a direction pin. The MAX3004–MAX3012 unidirectional level
translators level shift data in one direction (VL → VCC or
V CC → V L ) on any single data line. The
MAX3000E/MAX3001E/ MAX3002–MAX3012 accept VL
from +1.2V to +5.5V. All devices have VCC ranging
from +1.65V to +5.5V, making them ideal for data transfer between low-voltage ASICs/PLDs and higher voltage systems.
The MAX3000E/MAX3001E/MAX3002/MAX3004–
MAX3012 feature an output enable mode that reduces
VCC supply current to less than 2µA, and VL supply
current to less than 2µA when in shutdown. The
MAX3000E/MAX3001E have ±15kV ESD protection on
the VCC side for greater protection in applications that
route signals externally. The MAX3000E operates at a
guaranteed data rate of 230kbps; the MAX3001E operates at a guaranteed data rate of 4Mbps and the
MAX3002–MAX3012 are guaranteed with a data rate of
20Mbps of operation over the entire specified operating
voltage range.
Level Translation
For proper operation, ensure that +1.65V ≤ VCC ≤ +5.5V,
+1.2V ≤ VL ≤ +5.5V, and VL ≤ VCC. During power-up
sequencing, VL ≥ VCC does not damage the device.
During power-supply sequencing, when VCC is floating
and V L is powering up, up to 10mA current can be
sourced to each load on the VL side, yet the device does
not latch up.
The maximum data rate also depends heavily on the
load capacitance (see the Typical Operating
Characteristics), output impedance of the driver, and
the operational voltage range (see the Timing
Characteristics table).
Input Driver Requirements
The MAX3001E/MAX3002–MAX3012 architecture is
based on a one-shot accelerator output stage. See
Figure 5. Accelerator output stages are always in three-
state except when there is a transition on any of the
translators on the input side, either I/O VL or I/O VCC.
When there is such a transition, the accelerator stages
become active, charging (discharging) the capacitances
at the I/Os. Due to its bidirectional nature, both stages
become active during the one-shot pulse. This can lead
to some current feeding into the external source that is
driving the translator. However, this behavior helps to
speed up the transition on the driven side.
For proper full-speed operation, the output current
of a device that drives the inputs of the MAX3000E/
MAX3001E/MAX3002–MAX3012 should meet the following requirements:
• MAX3000E (230kbps):
i > 1mA, Rdrv < 1kΩ
• MAX3001E (4Mbps):
i > 107 x V x (C + 10pF)
• MAX3002–MAX3012 (20Mbps):
i > 108 x V x (C + 10pF)
where i is the driver output current, V is the logic-supply
voltage (i.e., VL or VCC) and C is the parasitic capacitance of the signal line.
Enable Output Mode (EN, EN A/B)
The MAX3000E/MAX3001E/MAX3002 and the MAX3004–
MAX3012 feature an EN input, and the MAX3003 has an
EN A/B input. Pull EN low to set the MAX3000E/
MAX3001E/MAX3002/MAX3004–MAX3012s’ I/O VCC1
through I/O VCC8 in three-state output mode, while I/O
VL1 through I/O VL8 have internal 6kΩ pulldown resistors.
Drive EN to logic-high (VL) for normal operation. The
MAX3003 is intended for bus multiplexing or bus switching applications. Drive EN A/B low to place channels 1B
through 4B in active mode, while channels 1A through
4A are in three-state mode. Drive EN A/B to logic-high
(VL) to enable channels 1A through 4A, while channels
1B through 4B remain in three-state mode.
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electrostatic discharges encountered during handling and
assembly. The I/O V CC lines have extra protection
against static discharge. Maxim’s engineers have
developed state-of-the-art structures to protect these
pins against ESD of ±15kV without damage. The ESD
structures withstand high ESD in all states: normal
operation, three-state output mode, and powered
down. After an ESD event, Maxim’s E versions keep
working without latchup, whereas competing products
can latch and must be powered down to remove
latchup.
______________________________________________________________________________________
15
MAX3000E/MAX3001E/MAX3002–MAX3012
Detailed Description
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
VL
VCC
I/O VL_ TO I/O VCC_ PATH
P
ONE-SHOT
6kΩ
I/O VL
I/O VCC
N
ONE-SHOT
P
ONE-SHOT
6kΩ
N
ONE-SHOT
I/O VCC_ TO I/O VL_ PATH
Figure 5. MAX3001E/MAX3002–MAX3012 Simplified Functional Diagram (1 I/O Line)
ESD protection can be tested in various ways. The
I/O VCC lines of the MAX3000E/MAX3001E are characterized for protection to ±15kV using the Human
Body Model.
IIN
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
VTH_IN / 6kΩ
Human Body Model
Figure 7a shows the Human Body Model and Figure 7b
shows the current waveform it generates when discharged into a low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.5kΩ resistor.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resistance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. Of course, all pins require this protection during manufacturing, not just inputs and outputs.
Therefore, after PCB assembly, the Machine Model is
less relevant to I/O ports.
16
0
VIN
VTH_IN
VS
-(VS - VTH_IN) / 6kΩ
WHERE VS = VCC OR VL
Figure 6. Typical IIN vs. VIN
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
Power-Supply Decoupling
To reduce ripple and the chance of transmitting incorrect data, bypass VL and VCC to ground with a 0.1µF
capacitor. To ensure full ±15kV ESD protection, bypass
VCC to ground with a 1µF capacitor. Place all capacitors as close to the power-supply inputs as possible.
I2C Level Translation
For I2C level translation for I2C applications, please refer
to the MAX3372E–MAX3379E/MAX3390E–MAX3393E
datasheet.
Unidirectional vs. Bidirectional Level
Translator
The MAX3000E/MAX3001E/MAX3002/MAX3003 bidirectional translators can operate as a unidirectional
device to translate signals without inversion. The
MAX3004–MAX3012 unidirecitional level translators,
level-shift data in one direction (VL → VCC or VCC → VL)
on any single data line (see the Ordering Information.)
These devices provide the smallest solution (UCSP
package) for unidirectional level translation without
inversion.
______________________________________________________________________________________
17
MAX3000E/MAX3001E/MAX3002–MAX3012
Applications Information
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
RC 1MΩ
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
CS
100pF
RD 1500Ω
IP 100%
90%
DISCHARGE
RESISTANCE
Ir
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
36.8%
DEVICE
UNDER
TEST
STORAGE
CAPACITOR
10%
0
0
TIME
tRL
tDL
CURRENT WAVEFORM
Figure 7a. Human Body ESD Test Model
Figure 7b. Human Body Current Waveform
Selector Guide
PART
EN
EN A/B
Tx/Rx*
DATA RATE
ESD PROTECTION
(kV)
MAX3000E
√
—
8/8
230kbps
±15
MAX3001E
√
—
8/8
4Mbps
±15
MAX3002
√
—
8/8
**
±2
MAX3003
—
√
8/8
**
±2
MAX3004
√
—
8/0
**
±2
MAX3005
√
—
7/1
**
±2
MAX3006
√
—
6/2
**
±2
MAX3007
√
—
5/3
**
±2
MAX3008
√
—
4/4
**
±2
MAX3009
√
—
3/5
**
±2
MAX3010
√
—
2/6
**
±2
MAX3011
√
—
1/7
**
±2
MAX3012
√
—
0/8
**
±2
*Tx = VL → VCC; Rx = VCC → VL
**See Table 1.
Table 1. Data Rate
18
VL ↔ VCC (V)
MAX3002–MAX3012
GUARANTEED DATA RATE
(Mbps)
1.2 ↔ 5.5
40
1.2 ↔ 3.3
20
2.5 ↔ 3.3
35
1.8 ↔ 2.5
30
1.2 ↔ 2.5
20
1.2 ↔ 1.8
20
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
VL
VCC
EN
MAX3000E/
MAX3001E/MAX3002
I/O VL1
I/O VCC1
I/O VL2
I/O VCC2
I/O VL3
I/O VCC3
I/O VL4
I/O VCC4
I/O VL5
I/O VCC5
I/O VL6
I/O VCC6
I/O VL7
I/O VCC7
I/O VL8
I/O VCC8
GND
______________________________________________________________________________________
19
MAX3000E/MAX3001E/MAX3002–MAX3012
MAX3000E/MAX3001E/MAX3002 Functional Diagram
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
MAX3000E/MAX3001E/MAX3002–MAX3012
MAX3003 Functional Diagram
VL
VCC
EN A/B
MAX3003
I/O VL1A
I/O VCC1A
I/O VL2A
I/O VCC2A
I/O VL3A
I/O VCC3A
I/O VL4A
I/O VCC4A
I/O VL1B
I/O VCC1B
I/O VL2B
I/O VCC2B
I/O VL3B
I/O VCC3B
I/O VL4B
I/O VCC4B
GND
20
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
MAX3000E/MAX3001E/MAX3002
MAX3004–MAX3012
MAX3003
1
2
3
4
5
VCC
I/O VCC2
I/O VCC4
I/O VCC6
I/O VCC8
I/O VCC1
I/O VCC3
I/O VCC5
I/O VCC7
GND
I/O VL1
I/O VL3
I/O VL5
I/O VL7
EN
VL
I/O VL2
I/O VL4
I/O VL6
I/O VL8
D
1
2
VCC
I/O VCC2A
I/O VCC4A I/O VCC2B
I/O VCC4B
I/O VCC1A
I/O VCC3A
I/O VCC1B I/O VCC3B
GND
I/O VL1A
I/O VL3A
I/O VL1B
I/O VL3B
EN A/B
VL
I/O VL2A
I/O VL4A
I/O VL2B
I/O VL4B
3
4
5
D
C
C
B
B
A
A
20 UCSP (Bottom View)
20 UCSP (Bottom View)
MAX3000E/MAX3001E/MAX3002
MAX3003
TOP VIEW
20 I/O VCC1
I/O VL1 1
20 I/O VCC1A
I/O VL1A 1
19 VCC
VL 2
19 VCC
VL 2
I/O VL2 3
18 I/O VCC2
I/O VL2A 3
18 I/O VCC2A
I/O VL3 4
17 I/O VCC3
I/O VL3A 4
17 I/O VCC3A
I/O VL4 5
16 I/O VCC4
I/O VL4A 5
16 I/O VCC4A
I/O VL5 6
15 I/O VCC5
I/O VL1B 6
15 I/O VCC1B
I/O VL6 7
14 I/O VCC6
I/O VL2B 7
14 I/O VCC2B
I/O VL7 8
13 I/O VCC7
I/O VL3B 8
13 I/O VCC3B
I/O VL8 9
12 I/O VCC8
I/O VL4B 9
12 I/O VCC4B
EN 10
EN A/B 10
11 GND
11 GND
TSSOP
VL
I/O VL1A
I/O VCC1A
VCC
I/O VCC2A
18
17
16
I/O VCC2
16
19
VCC
17
20
I/O VL1
I/O VCC1
18
VL
TSSOP
19
20
TOP VIEW
14
I/O VCC4A
I/O VL4
3
13
I/O VCC5
I/O VL4A
3
13
I/O VCC1B
I/O VL5
4
12
I/O VCC6
I/O VL1B
4
12
I/O VCC2B
I/O VL6
5
*EXPOSED PADDLE
11
I/O VCC7
I/O VL2B
5
11
I/O VCC3B
5mm ✕ 5mm THIN QFN
MAX3003
6
7
8
9
10
I/O VL4B
EN A/B
GND
I/O VCC4B
*EXPOSED PADDLE
I/O VL3B
10
I/O VL3A
2
MAX3000E/
MAX3001E/
MAX3002
I/O VCC4
I/O VCC8
14
9
I/O VCC3A
2
GND
15
I/O VL3
8
1
EN
I/O VL2A
7
I/O VCC3
6
15
I/O VL8
1
I/O VL7
I/O VL2
5mm ✕ 5mm THIN QFN
______________________________________________________________________________________
21
MAX3000E/MAX3001E/MAX3002–MAX3012
Pin Configurations
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
MAX3000E/MAX3001E/MAX3002–MAX3012
Pin Configurations (continued)
TOP VIEW
MAX3004
20 O VCC1
I VL1 1
VL 2
I VL2 3
I VL3 4
19 VCC
VL 2
18 O VCC2
17 O VCC3
I VL3 4
I VL4 5
16 O VCC4
I VL5 6
I VL6 7
MAX3006
20 I VCC1
O VL1 1
I VL2 3
19 VCC
20 I VCC1
O VL1 1
VL 2
19 VCC
18 O VCC2
O VL2 3
18 I VCC2
17 O VCC3
I VL3 4
17 O VCC3
I VL4 5
16 O VCC4
I VL4 5
16 O VCC4
15 O VCC5
I VL5 6
15 O VCC5
I VL5 6
15 O VCC5
14 O VCC6
I VL6 7
14 O VCC6
I VL6 7
14 O VCC6
I VL7 8
13 O VCC7
I VL7 8
13 O VCC7
I VL7 8
13 O VCC7
I VL8 9
12 O VCC8
I VL8 9
12 O VCC8
I VL8 9
12 O VCC8
EN 10
11 GND
EN 10
11 GND
EN 10
11 GND
TSSOP
TSSOP
TSSOP
MAX3007
MAX3008
MAX3009
20 I VCC1
O VL1 1
19 VCC
VL 2
20 I VCC1
O VL1 1
19 VCC
VL 2
20 I VCC1
O VL1 1
19 VCC
VL 2
O VL2 3
18 I VCC2
O VL2 3
18 I VCC2
O VL2 3
18 I VCC2
O VL3 4
17 I VCC3
O VL3 4
17 I VCC3
O VL3 4
17 I VCC3
I VL4 5
16 O VCC4
O VL4 5
16 I VCC4
O VL4 5
16 I VCC4
I VL5 6
15 O VCC5
I VL5 6
15 O VCC5
O VL5 6
15 I VCC5
I VL6 7
14 O VCC6
I VL6 7
14 O VCC6
I VL6 7
14 O VCC6
I VL7 8
13 O VCC7
I VL7 8
13 O VCC7
I VL7 8
13 O VCC7
I VL8 9
12 O VCC8
I VL8 9
12 O VCC8
I VL8 9
12 O VCC8
EN 10
11 GND
TSSOP
22
MAX3005
EN 10
11 GND
TSSOP
EN 10
11 GND
TSSOP
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
TOP VIEW
MAX3010
MAX3011
20 I VCC1
O VL1 1
VL 2
20 I VCC1
O VL1 1
VL 2
19 VCC
O VL2 3
18 I VCC2
O VL2 3
O VL3 4
O VL4 5
MAX3012
20 I VCC1
O VL1 1
VL 2
19 VCC
19 VCC
18 I VCC2
O VL2 3
18 I VCC2
17 I VCC3
O VL3 4
17 I VCC3
O VL3 4
17 I VCC3
16 I VCC4
O VL4 5
16 I VCC4
O VL4 5
16 I VCC4
O VL5 6
15 I VCC5
O VL5 6
15 I VCC5
O VL5 6
15 I VCC5
O VL6 7
14 I VCC6
O VL6 7
14 I VCC6
O VL6 7
14 I VCC6
I VL7 8
13 O VCC7
O VL7 8
13 I VCC7
O VL7 8
13 I VCC7
I VL8 9
12 O VCC8
I VL8 9
12 O VCC8
O VL8 9
12 I VCC8
EN 10
EN 10
11 GND
TSSOP
11 GND
EN 10
11 GND
TSSOP
TSSOP
Ordering Information (continued)
TEMP RANGE
PIN-PACKAGE
TEMP RANGE
PIN-PACKAGE
MAX3001EEUP
PART
-40°C to +85°C
20 TSSOP
MAX3007EUP
-40°C to +85°C
20 TSSOP
MAX3001EEBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3007EBP-T*
-40°C to +85°C
4 x 5 UCSP
PART
MAX3001EETP
-40°C to +85°C
20 TQFN
MAX3008EUP
-40°C to +85°C
20 TSSOP
MAX3001EAUP
-40°C to +125°C
20 TSSOP
MAX3008EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3002EUP
-40°C to +85°C
20 TSSOP
MAX3009EUP
-40°C to +85°C
20 TSSOP
MAX3002EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3009EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3002ETP
-40°C to +85°C
20 TQFN
MAX3010EUP
-40°C to +85°C
20 TSSOP
4 x 5 UCSP
MAX3003EUP
-40°C to +85°C
20 TSSOP
MAX3010EBP-T*
-40°C to +85°C
MAX3003EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3011EUP
-40°C to +85°C
20 TSSOP
MAX3003ETP
-40°C to +85°C
20 TQFN
MAX3011EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3004EUP
-40°C to +85°C
20 TSSOP
MAX3012EUP
-40°C to +85°C
20 TSSOP
MAX3004EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3012EBP-T*
-40°C to +85°C
4 x 5 UCSP
MAX3005EUP
-40°C to +85°C
20 TSSOP
MAX3005EBP-T*
-40°C to +85°C
4 x 5 UCSP
*Future product—contact factory for availability.
-T = Tape-and-reel package.
MAX3006EUP
-40°C to +85°C
20 TSSOP
MAX3006EBP-T*
-40°C to +85°C
4 x 5 UCSP
Chip Information
TRANSISTOR COUNT: 1184
PROCESS: BiCMOS
______________________________________________________________________________________
23
MAX3000E/MAX3001E/MAX3002–MAX3012
Pin Configurations (continued)
MAX3000E/MAX3001E/MAX3002–MAX3012
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
24
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
20 TSSOP
U20-3
21-0066
20 TQFN
T2055-4
21-0140
4 x 5 UCSP
B20-1
21-0095
______________________________________________________________________________________
+1.2V to +5.5V, ±15kV ESD-Protected, 0.1µA,
35Mbps, 8-Channel Level Translators
REVISION
NUMBER
REVISION
DATE
4
12/06
Added TQFN packages
5
8/08
Changed pin description and package drawing
DESCRIPTION
PAGES
CHANGED
1, 2, 3, 10, 11, 15,
16, 21, 23–26
1, 10, 11, 23
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 25
© 2008 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products.
MAX3000E/MAX3001E/MAX3002–MAX3012
Revision History