MAXIM MAX3059ASA

19-2939; Rev 1; 9/03
5V, 1Mbps, Low Supply Current
CAN Transceivers
The MAX3058 features four different modes of operation: high speed, slope control, standby, and shutdown.
The MAX3059 features three different modes of operation: high speed, slope control, and shutdown. Highspeed mode allows data rates up to 1Mbps. In
slope-control mode, the slew rate may be optimized for
data rates up to 500kbps, so the effects of EMI are
reduced, and unshielded twisted or parallel cable can
be used. In standby mode, the transmitters are shut off
and the receivers are put into low-current mode. In
shutdown mode, the transmitter and receiver are
switched off.
The MAX3058/MAX3059 are available in an 8-pin SO
package and are specified over the -40°C to +125°C
temperature range.
Applications
Features
♦ Four Operating Modes
High-Speed Operation Up to 1Mbps
Slope-Control Mode to Reduce EMI (40kbps to
500kbps)
Low-Current Shutdown Mode
Standby Mode (MAX3058 Only)
♦ Thermal Shutdown
♦ Current Limiting
♦ ESD Protection
±12kV Human Body Model
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX3058ASA
-40°C to +125°C
8 SO
MAX3059ASA
-40°C to +125°C
8 SO
Selector Guide
TERMINATION
RESISTOR
STANDBY
MAX3058ASA
No
Yes
MAX3059ASA
Yes
No
PART
Printers JetLink
Industrial Control Networks
Pin Configurations
Telecom Backplane
Consumer Applications
TOP VIEW
TXD 1
8
GND 2
RS
TXD 1
8
RS
7
CANH
GND 2
7
CANH
3
6
CANL
VCC
3
6
CANL
RXD 4
5
SHDN
RXD 4
5
TERM
MAX3058
VCC
SO
MAX3059
SO
Typical Operating Circuit appears at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX3058/MAX3059
General Description
The MAX3058/MAX3059 interface between the controller area network (CAN) protocol controller and the
physical wires of the bus lines in a CAN. They are primarily intended for printer and telecom backplane applications requiring data rates up to 1Mbps. These
devices provide differential transmit capability to the bus
and differential receive capability to the CAN controller.
The MAX3058 output common-mode range is from -7V
to +12V. The MAX3059 output common-mode range is
from 0V to V CC. The MAX3059 contains an internal
switch termination resistor that makes it ideal for JetLink
applications.
MAX3058/MAX3059
5V, 1Mbps, Low Supply Current
CAN Transceivers
ABSOLUTE MAXIMUM RATINGS
VCC to GND ..............................................................-0.3V to +6V
TXD, RS, SHDN, TERM to GND................................-0.3V to +6V
RXD to GND .............................................................-0.3V to +6V
CANH, CANL to GND (MAX3058).......................-7.5V to +12.5V
CANH, CANL to GND (MAX3059)..............-0.3V to (VCC + 0.3V)
Continuous Power Dissipation (TA = +70°C)
8-Pin SO (derate 5.9mW/°C above +70°C)..................470mW
Operating Temperature Range .........................-40°C to +125°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +5V ±10%, TA = TMIN to TMAX, RL = 60Ω, CL = 100pF. Typical values are at VCC = +5V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Supply Current
IS
Quiescent Current Standby Mode
IQ
TYP
MAX
Dominant
CONDITIONS
MIN
40
70
Recessive
2
5
Standby, MAX3058
15
80
VSHDN = VCC, MAX3058
Shutdown Current
Thermal-Shutdown Threshold
ISHDN
UNITS
mA
µA
5
VTERM = VRS = VCC, MAX3059
10
VTERM = 0V, VRS = VCC, MAX3059
150
VTSH
Thermal-Shutdown Hysteresis
µA
160
°C
25
°C
TXD INPUT LEVELS
High-Level Input Voltage
VIH
Low-Level Input Voltage
VIL
Input Capacitance
CIN
Pullup Resistor
2
(Note 3)
V
5
RINTXD
50
High-Level Input Voltage
VTRH
2
Low-Level Input Voltage
VTRL
TERM Pullup Resistor
RPU
0.8
V
20
pF
100
kΩ
TERM INPUT LEVELS (MAX3059)
V
0.8
V
50
100
kΩ
CANH, CANL TRANSMITTER
2
3
V
VTXD = VCC, no load, VRS = VCC
(standby mode), MAX3058
-100
+100
mV
VCANH
VTXD = 0V
2.75
VCC 0.8V
V
VCANL
VTXD = 0V
0.5
2.25
V
VTXD = 0V, VCC = 5V ±5%
1.5
3
VTXD = 0V, VCC = 5V ±10%
1.5
3.2
VTXD = 0V, RL = 45Ω
1.2
3
VTXD = VCC, no load
-500
+50
Recessive Bus Voltage
VCANH,
VCANL
CANH Output Voltage
CANL Output Voltage
Differential Output
(VCANH - VCANL)
2
∆VCANH,
VCANL
VTXD = VCC, no load
_______________________________________________________________________________________
V
mV
5V, 1Mbps, Low Supply Current
CAN Transceivers
(VCC = +5V ±10%, TA = TMIN to TMAX, RL = 60Ω, CL = 100pF. Typical values are at VCC = +5V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CANH Short-Circuit Current
ICANHSC
CANL Short-Circuit Current
ICANLSC
Termination Resistor
RTERM
CONDITIONS
MIN
-7V ≤ VCANH ≤ 0V, MAX3058
-200
TYP
-30
VCANH = 0V, MAX3059
-200
-30
VCC ≤ VCANL ≤ 12V, MAX3058
30
200
VCANL = VCC, MAX3059
30
200
VTERM = VCC, MAX3059
108
0.8 x
VCC
120
MAX
UNITS
mA
mA
132
Ω
VCC
V
0.4
V
RXD OUTPUT LEVELS
RXD High-Output Voltage Level
VOH
I = -100µA
RXD Low-Output Voltage Level
VOL
I = 1.6mA
DC BUS RECEIVER (Note 2)
MAX3058
Differential Input Voltage
(Recessive)
Differential Input Voltage
(Dominant)
Differential Input Hysteresis
CANH and CANL Input
Resistance
Differential Input Resistance
VDIFF
VDIFF
MAX3058, VRS = VCC (standby mode)
-17
+0.5
-17
+0.5
MAX3059
-VCC
+0.5
MAX3058
0.9
17
MAX3058, VRS = VCC (standby mode)
1.1
17
MAX3059
0.9
VCC
VDIFF(HYST)
100
V
V
mV
RI
5
25
kΩ
RDIFF
10
100
kΩ
0.3 x
VCC
V
MODE SELECTION (RS)
Input Voltage for High Speed
VSLP
VSTBY
MAX3058
VSHDN
MAX3059
Slope-Control Mode Voltage
VSLOPE
RRS = 25kΩ to 200kΩ
0.4 x
VCC
0.6 x
VCC
V
Slope-Control Mode Current
ISLOPE
RRS = 25kΩ to 200kΩ
-10
-200
µA
-500
µA
0.8
V
100
kΩ
Input Voltage for Standby
High-Speed Mode Current
IHS
0.75 x
VCC
VRS = 0V
V
SHUTDOWN (MAX3058)
SHDN Input Voltage High
VSHDNH
SHDN Input Voltage Low
VSHDNL
SHDN Pulldown Resistor
RINDHDN
2
50
V
_______________________________________________________________________________________
3
MAX3058/MAX3059
DC ELECTRICAL CHARACTERISTICS (continued)
MAX3058/MAX3059
5V, 1Mbps, Low Supply Current
CAN Transceivers
TIMING CHARACTERISTICS
(VCC = +5V ±10%, RL = 60Ω, CL = 100pF, TA = TMIN to TMAX. Typical values are at VCC = +5V and TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
VRS = 0V (≤ 1Mbps)
Delay TXD to Bus Active,
Figure 1
tONTXD
tOFFTXD
125
RRS = 100kΩ (≤ 125kbps)
450
RRS = 200kΩ (≤ 62.5kbps)
700
tONRXD
180
RRS = 100kΩ (≤ 125kbps)
500
RRS = 200kΩ (≤ 62.5kbps)
1000
Differential Output Slew Rate
Bus Dominant to RXD Active
Standby to Receiver Active
tOFFRXD
SR
ns
80
RRS = 25kΩ (≤ 500kbps)
150
RRS = 100kΩ (≤ 125kbps)
500
RRS = 200kΩ (≤ 62.5kbps)
800
VRS = 0V (≤ 1Mbps)
Delay Bus to Receiver Inactive,
Figure 1
ns
70
RRS = 25kΩ (≤ 500kbps)
VRS = 0V (≤ 1Mbps)
Delay Bus to Receiver Active,
Figure 1
UNITS
50
RRS = 25kΩ (≤ 500kbps)
VRS = 0V (≤ 1Mbps)
Delay TXD to Bus Inactive,
Figure 1
MAX
ns
100
RRS = 25kΩ (≤ 500kbps)
210
RRS = 100kΩ (≤ 125kbps)
500
RRS = 200kΩ (≤ 62.5kbps)
1100
VRS = 0V (≤ 1Mbps)
100
RRS = 25kΩ (≤ 500kbps)
7
RRS = 100kΩ (≤ 125kbps)
1.6
RRS = 200kΩ (≤ 62.5kbps)
0.8
ns
V/µs
tDRXDL
VRS > 0.8 x VCC (standby), MAX3058,
Figure 2
1
µs
tSBRXDL
µs
BUS dominant, MAX3058, Figure 2
4
SHDN to Bus Inactive
tOFFSHDN
TXD = GND, MAX3058, Figure 3 (Note 4)
1
µs
SHDN to Receiver Active
tONSHDN
BUS dominant, MAX3058, Figure 3 (Note 5)
4
µs
RS to Bus Inactive
tOFFSHDN
TXD = GND, MAX3059, Figure 3 (Note 4)
1
µs
RS to Receiver Active
tONSHDN
BUS dominant, MAX3059, Figure 3 (Note 5)
4
µs
TERM to Resistor Switched On
tONRT
VRS = VCC (part in shutdown), MAX3059,
Figure 4
400
ns
TERM to Resistor Switched Off
tOFFRT
VRS = VCC (part in shutdown),
MAX3059, Figure 4
400
ns
ESD Protection
Human Body Model
12
±kV
Note 1: All currents into device are positive; all currents out of the device are negative. All voltages are referenced to device ground,
unless otherwise noted.
Note 2: (VTXD = VCC; CANH and CANL externally driven; -7V < VCANH, VCANL < 12V for MAX3058; 0V < VCANH, VCANL < VCC for
MAX3059, unless otherwise specified).
Note 3: Specification guaranteed by design, not production tested.
Note 4: No other devices on the BUS.
Note 5: BUS externally driven.
4
_______________________________________________________________________________________
5V, 1Mbps, Low Supply Current
CAN Transceivers
TXD
VCC/2
RS
VCC/2
VCC x 0.75
BUS EXTERNALLY
DRIVEN
tOFFTXD
tONTXD
0.9V
VDIFF
tSBRXDL
0.5V
tONRXD
RXD
1.1V
VDIFF
tOFFRXD
VCC/2
VCC/2
Figure 1. Timing Diagram
tDRXDL
RXD
VCC/2
VCC/2
Figure 2. Timing Diagram for Standby Signal (MAX3058)
500Ω
CANH
SHDN
VCC/2
VCC/2
VCC
CL
CANL
500Ω
tONSHDN
tOFFSHDN
VDIFF
0.5V
BUS EXTERNALLY
DRIVEN
TERM
VCC/2
tONRT
RXD
VCC/2
tOFFRT
VCC/2
CANH
VCC - 1V
VCC - 1V
Figure 3. Timing Diagram for Shutdown Signal
Figure 4. Test Circuit and Diagram for TERM Timing (MAX3059)
_______________________________________________________________________________________
5
MAX3058/MAX3059
Timing Diagrams
Typical Operating Characteristics
(VCC = +5V, RL = 60Ω, CL = 100pF, TA = +25°C, unless otherwise specified.)
SLEW RATE vs. RRS AT 100kbps
15
10
5
TA = +25°C
MAX3058/59 toc03
TA = -40°C
74
73
SUPPLY CURRENT (µA)
SUPPLY CURRENT (mA)
30
75
MAX3058/59 toc02
35
MAX3058/59 toc01
20
SLEW RATE (V/µs)
MAX3059
SUPPLY CURRENT vs. TEMPERATURE
IN SHUTDOWN MODE (TERM = GND)
SUPPLY CURRENT vs. DATA RATE
25
25
20
TA = +125°C
72
71
70
69
68
67
15
66
0
65
10
10
48
86
124
200
162
DATA RATE (kbps)
TEMPERATURE (°C)
MAX3059
SUPPLY CURRENT vs. TEMPERATURE
IN SHUTDOWN MODE (TERM = VCC)
RECEIVER PROPAGATION DELAY
vs. TEMPERATURE
DRIVER PROPAGATION DELAY
vs. TEMPERATURE
6
5
4
3
2
70
60
50
40
DOMINANT
30
20
1
10
0
0
-7
26
59
10
RRS = GND
92
125
-40
-7
59
3.0
2
1
TA = +125°C
2.5
VOLTAGE RXD (V)
3
MAX3058/59 toc08
SHDN = VCC
RS = GND
TXD = VCC
26
TEMPERATURE (°C)
RECEIVER OUTPUT LOW
vs. OUTPUT CURRENT
MAX3058/59 toc07
SUPPLY CURRENT (µA)
RECESSIVE
20
TEMPERATURE (°C)
MAX3058
SUPPLY CURRENT
vs. TEMPERATURE IN SHUTDOWN
4
30
0
TEMPERATURE (°C)
5
DOMINANT
40
RRS = GND
-40
-40 -25 -10 5 20 35 50 65 80 95 110 125
MAX3058/59 toc06
RECESSIVE
DRIVER PROPAGATION DELAY (ns)
7
90
80
50
MAX3058/59 toc05
8
100
RECEIVER PROPAGATION DELAY (ns)
MAX3058/59 toc04
9
TA = +25°C
2.0
1.5
TA = -40°C
1.0
0.5
0
0
-40
-7
26
59
TEMPERATURE (°C)
6
-40 -25 -10 5 20 35 50 65 80 95 110 125
0 100 200 300 400 500 600 700 800 900 1000
RRS (kΩ)
10
SUPPLY CURRENT (µA)
MAX3058/MAX3059
5V, 1Mbps, Low Supply Current
CAN Transceivers
92
125
10
13
16
19
22
25
OUTPUT CURRENT (mA)
_______________________________________________________________________________________
92
125
5V, 1Mbps, Low Supply Current
CAN Transceivers
RECEIVER OUTPUT HIGH
vs. OUTPUT CURRENT
3.5
3.0
TA = +25°C
2.5
2.0
1.5
TA = -40°C
TA = -40°C
4.5
4.0
TA = +25°C
3.5
3.0
2.5
TA = +125°C
2.0
1.5
1.0
1.0
0.5
0.5
0
MAX3058/59 toc10
TA = +125°C
0
10 11 12 13 14 15 16 17 18 19 20 21 22 23
0
OUTPUT CURRENT (mA)
50
100
150
200
250
300
DIFFERENTIAL LOAD RL (Ω)
RECEIVER PROPAGATION DELAY
DRIVER PROPAGATION DELAY
MAX3058/59 toc11
MAX3058/59 toc12
TXD
5V/div
CANH CANL
RRS =
24kΩ
RRS =
100kΩ
RXD
2V/div
RRS =
180kΩ
200ns/div
1µs/div
DRIVER PROPAGATION DELAY (RS = GND)
LOOPBACK PROPAGATION DELAY
vs. RRS
MAX3058/59 toc13
TXD
5V/div
CANH CANL
LOOPBACK PROPAGATION DELAY (ns)
900
MAX3058/59 toc14
4.0
5.0
DIFFERENTIAL VOLTAGE (V)
4.5
MAX3058/59 toc09
RECEIVER OUTPUT HIGH (VCC - RXD) (V)
5.0
DIFFERENTIAL VOLTAGE
vs. DIFFERENTIAL LOAD RL
800
700
600
500
400
300
200
100
0
200ns/div
0
20 40 60 80 100 120 140 160 180 200
RRS (kΩ)
_______________________________________________________________________________________
7
MAX3058/MAX3059
Typical Operating Characteristics (continued)
(VCC = +5V, RL = 60Ω, CL = 100pF, TA = +25°C, unless otherwise specified.)
MAX3058/MAX3059
5V, 1Mbps, Low Supply Current
CAN Transceivers
Pin Description
PIN
NAME
FUNCTION
MAX3058
MAX3059
1
1
TXD
2
2
GND
Ground
3
3
VCC
Supply Voltage. Bypass VCC to GND with a 0.1µF capacitor.
4
4
RXD
Transmit Data Input. TXD is a CMOS/TTL-compatible input from a CAN controller. TXD has an
internal 75kΩ pullup resistor.
Receive Data Output. RXD is a CMOS/TTL-compatible output.
SHDN
Shutdown Input, CMOS/TTL-Compatible Input. Drive SHDN high to put the IC into shutdown
mode. SHDN has an internal 75kΩ pulldown resistor to GND.
6
CANL
CAN Bus Line Low
7
CANH
CAN Bus Line High
5
—
6
7
8
8
RS
—
5
TERM
Mode Select Input. Drive RS low or connect to GND for high-speed operation. Connect a
resistor between RS and GND to control output slope. For the MAX3058, drive RS high to put
into standby mode. (see Mode Selection section). For the MAX3059, drive RS above 0.75 x VCC
to select shutdown mode.
Terminate Input, CMOS/TTL Compatible. Drive TERM high or leave floating to terminate the
device with a 120Ω across the CANH and CANL. Drive TERM low to disconnect this resistor.
TERM has an internal 75kΩ pullup resistor to VCC.
Functional Diagram
VCC
THERMAL
SHUTDOWN
MAX3058/
MAX3059
VCC
CANH
Rb
TRANSMITTER
CONTROL
TXD
RT
VCC/2
+
Rb
-
VCC
RS
CANL
MODE
SELECTION
TERM
(MAX3059)
RXD
RECEIVER
SHUTDOWN
GND
SHDN
(MAX3058)
0.75V
8
_______________________________________________________________________________________
5V, 1Mbps, Low Supply Current
CAN Transceivers
The MAX3058/MAX3059 interface between the protocol
controller and the physical wires of the bus lines in a
CAN. They are primarily intended for printer and telecom backplane applications requiring data rates up to
1Mbps. These devices provide differential transmit
capability to the bus and differential receive capability
to the CAN controller.
The MAX3058 output common-mode range is from -7V
to +12V. The MAX3059 output common-mode range is
from 0V to V CC. The MAX3059 contains an internal
switch termination resistor that makes it ideal for JetLink
applications.
The MAX3058 features four different modes of operation: high-speed, slope control, standby, and shutdown. The MAX3059 features three different modes of
operation: high speed, slope control, and shutdown.
High-speed mode allows data rates up to 1Mbps. In
slope-control mode, the slew rate may be optimized for
data rates up to 500kbps, so the effects of EMI are
reduced, and unshielded twisted or parallel cable can
be used. In standby mode, the transmitters are shut off
and the receivers are put into low-current mode. In
shutdown mode, the transmitter and receiver are
switched off.
The transceivers operate from a single +5V supply and
draw 40mA of supply current in dominant state and 2mA
in recessive state. In standby mode, supply current is
reduced to 15µA. In shutdown mode, supply current is
1µA for the MAX3058 and 5µA for the MAX3059.
CANH and CANL are output short-circuit current limited
and are protected against excessive power dissipation
by thermal-shutdown circuitry that places the driver
outputs into a high-impedance state.
Transmitter
The transmitter converts a single-ended input (TXD)
from the CAN controller to differential outputs for the
bus lines (CANH, CANL). The truth table for the transmitter and receiver is given in Tables 1 and 2.
Table 1. Transmitter and Receiver Truth Table for MAX3058 When Not Connected to
the Bus
TXD
RS
SHDN
Low
VRS < 0.75 x VCC
Low
CANH
CANL
BUS STATE
RXD
High
Low
Dominant
Low
5kΩ to 25kΩ
to VCC/2
Recessive
High
High or float
VRS < 0.75 x VCC
Low
5kΩ to 25kΩ to
VCC/2
X
VRS > 0.75 x VCC
Low
5kΩ to 25kΩ to
GND
5kΩ to 25kΩ
to GND
Recessive
High
X
X
High
Floating
Floating
Floating
High
Table 2. Transmitter and Receiver Truth Table for MAX3059 When Not Connected to
the Bus
TXD
RS
TERM
CANH
CANL
BUS STATE
RXD
Low
VRS < 0.75 x VCC
Low
High
Low
Dominant
Low
Low
VRS < 0.75 x VCC
High
High
Low
Dominant
Low
High or float
VRS < 0.75 x VCC
Low
Recessive
High
High or float
VRS < 0.75 x VCC
High
Recessive
High
X
VRS > 0.75 x VCC
Low
Floating
High
Floating
High
120Ω terminating resistor across
5kΩ to 25kΩ to
VCC/2
5kΩ to 25kΩ to
VCC/2
5kΩ to 25kΩ to
VCC/2
5kΩ to 25kΩ to
VCC/2
120Ω terminating resistor across
X
VRS > 0.75 x VCC
High
Floating
Floating
Floating
Floating
120Ω terminating resistor across
_______________________________________________________________________________________
9
MAX3058/MAX3059
Detailed Description
MAX3058/MAX3059
5V, 1Mbps, Low Supply Current
CAN Transceivers
Receiver
The receiver reads differential input from the bus lines
(CANH, CANL) and transfers this data as a singleended output (RXD) to the CAN controller. It consists of
a comparator that senses the difference ∆V = (CANH CANL) with respect to an internal threshold of 0.7V. If
this difference is positive (i.e., ∆V > 0.7), a logic low is
present at RXD. If negative (i.e., ∆V < 0.7V), a logic
high is present. The receiver always echoes the CAN
BUS data.
The CANH and CANL common-mode range is -7V to
+12V for the MAX3058, and 0V to V CC for the
MAX3059. RXD is logic high when CANH and CANL
are either shorted, or terminated and undriven.
Mode Selection
Standby Mode
If a logic-high level is applied to RS, the MAX3058
enters a low-current standby mode. In this mode, the
transmitter is switched off and the receiver is switched
to a low-current/low-speed state. If dominant bits are
detected, RXD switches to low level. The microcontroller should react to this condition by switching the
transceiver back to normal operation.
When the MAX3058 enters standby mode, RXD goes
high for 4µs (max) regardless of the BUS state.
However, after 4µs, RXD goes low only when the BUS is
dominant; otherwise, RXD remains high (when the BUS
is recessive). For proper measurement of standby to
receiver active time (tSBRXDL), the BUS should be in a
dominant state (see Figure 2).
High-Speed Mode
Connect RS to ground to set the MAX3058/MAX3059 to
high-speed mode. When operating in high-speed
mode, the MAX3058/MAX3059 can achieve transmission rates of up to 1Mbps. In high-speed mode, use
shielded twisted-pair cable to avoid EMI problems.
Shutdown Mode
Drive SHDN high to enter shutdown mode on the
MAX3058. Connect SHDN to ground or leave it floating
for normal operation. On the MAX3059, drive RS high to
enter shutdown.
Slope-Control Mode
Connect a resistor from RS to ground to select slopecontrol mode (Table 3). In slope-control mode, CANH
and CANL slew rates are controlled by the resistor connected to the RS pin. Maximum transmission speeds
are controlled by R RS , and range from 40kbps to
500kbps. Controlling the rise and fall slopes reduces
EMI and allows the use of an unshielded twisted pair or
a parallel pair of wires as bus lines. The transfer function for selecting the resistor value is given by:
RRS (kΩ) ≈ 12,500/(maximum speed in kbps)
See the Slew Rate vs. RRS graph in the Typical Operating Characteristics.
Drive TERM high (to VCC) or leave it floating to terminate the MAX3059 with 120Ω resistor connected across
the CANH and CANL. Connect TERM to ground to disconnect this resistor.
TERM
Thermal Shutdown
If the junction temperature exceeds +160°C, the device
is switched off. The hysteresis is approximately 25°C,
disabling thermal shutdown once the temperature
drops to +135°C. In thermal shutdown, CANH and CANL
go recessive and all IC functions are disabled.
Table 3. Mode Selection Truth Table
10
CONDITION FORCED AT PIN RS
MODE
RESULTING CURRENT AT RS (µA)
VRS < 0.3 x VCC
High speed
|IRS| < 500
0.4 x VCC <VRS < 0.6 x VCC
Slope control
10µA < |IRS| < 200
VRS > 0.75 x VCC
Standby (MAX3058)
|IRS| < 10
VRS > 0.75 x VCC
Shutdown (MAX3059)
|IRS| < 10
______________________________________________________________________________________
5V, 1Mbps, Low Supply Current
CAN Transceivers
Reduced EMI and Reflections
In slope-control mode, the CANH and CANL outputs
are slew-rate limited, minimizing EMI and reducing
reflections caused by improperly terminated cables.
In multidrop CAN applications, it is important to maintain a direct point-to-point wiring scheme. A single pair
of wires should connect each element of the CAN bus,
and the two ends of the bus should be terminated with
120Ω resistors. A star configuration should never
be used.
Any deviation from the point-to-point wiring scheme
creates a stub. The high-speed edge of the CAN data
on a stub can create reflections back down the bus.
These reflections can cause data errors by eroding the
noise margin of the system.
Although stubs are unavoidable in a multidrop system,
care should be taken to keep these stubs as small as
possible, especially in high-speed mode. In slope-control mode, the requirements are not as rigorous, but
stub length should still be minimized.
Power Supply and Bypassing
The MAX3058/MAX3059 require no special layout considerations beyond common practices. Bypass VCC to
GND with a 0.1µF ceramic capacitor mounted close to
the IC with short lead lengths and wide trace widths.
Chip Information
TRANSISTOR COUNT: 1024
PROCESS: BiCMOS
Typical Operating Circuit
120Ω
VCC
0.1µF
VCC
CANH
CAN
CONTROLLER
MAX3058
TX0
TXD
RX0
RXD
CANL
SHDN
RS
GND
GND
25kΩ–200kΩ
120Ω
______________________________________________________________________________________
11
MAX3058/MAX3059
Applications Information
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
DIM
A
A1
B
C
e
E
H
L
N
E
H
INCHES
MILLIMETERS
MAX
MIN
0.069
0.053
0.010
0.004
0.014
0.019
0.007
0.010
0.050 BSC
0.150
0.157
0.228
0.244
0.016
0.050
MAX
MIN
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
1.27 BSC
3.80
4.00
5.80
6.20
0.40
SOICN .EPS
MAX3058/MAX3059
5V, 1Mbps, Low Supply Current
CAN Transceivers
1.27
VARIATIONS:
1
INCHES
TOP VIEW
DIM
D
D
D
MIN
0.189
0.337
0.386
MAX
0.197
0.344
0.394
MILLIMETERS
MIN
4.80
8.55
9.80
MAX
5.00
8.75
10.00
N MS012
8
AA
14
AB
16
AC
D
C
A
B
e
0 -8
A1
L
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, .150" SOIC
APPROVAL
DOCUMENT CONTROL NO.
21-0041
REV.
B
1
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.