PCA82C250 CAN controller interface Rev. 06 — 26 March 2009 Product data sheet 1. General description The PCA82C250 is the interface between a CAN protocol controller and the physical bus. The device provides differential transmit capability to the bus and differential receive capability to the CAN controller. 2. Features n n n n n n n n n n Fully compatible with the “ISO 11898” standard High speed (up to 1 MBd) Bus lines protected against transients in an automotive environment Slope control to reduce Radio Frequency Interference (RFI) Differential receiver with wide common-mode range for high immunity against ElectroMagnetic Interference (EMI) Thermally protected Short-circuit proof to battery and ground Low-current Standby mode An unpowered node does not disturb the bus lines At least 110 nodes can be connected 3. Applications n High-speed automotive applications (up to 1 MBd). 4. Quick reference data Table 1. Quick reference data Symbol Parameter VCC supply voltage ICC supply current 1/tbit maximum transmission speed VCAN CANH, CANL input/output voltage Vdiff differential bus voltage tPD propagation delay Tamb ambient temperature Conditions Min Max Unit 4.5 5.5 V Standby mode - 170 µA non-return-to-zero 1 - MBd −8 +18 V 1.5 3.0 V - 50 ns −40 +125 °C High-speed mode PCA82C250 NXP Semiconductors CAN controller interface 5. Ordering information Table 2. Ordering information Type number PCA82C250T Package Name Description Version SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 6. Block diagram VCC 3 TXD Rs PROTECTION 1 8 DRIVER SLOPE/ STANDBY HS 7 RXD 4 6 Vref CANH RECEIVER 5 REFERENCE VOLTAGE CANL PCA82C250 2 GND Fig 1. mka669 Block diagram 7. Pinning information 7.1 Pinning TXD 1 8 Rs GND 2 7 CANH PCA82C250 VCC 3 6 CANL RXD 4 5 Vref mka670 Fig 2. Pin configuration PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 2 of 17 PCA82C250 NXP Semiconductors CAN controller interface 7.2 Pin description Table 3. Pin description Symbol Pin Description TXD 1 transmit data input GND 2 ground VCC 3 supply voltage RXD 4 receive data output Vref 5 reference voltage output CANL 6 LOW-level CAN voltage input/output CANH 7 HIGH-level CAN voltage input/output Rs 8 slope resistor input 8. Functional description The PCA82C250 is the interface between a CAN protocol controller and the physical bus. It is primarily intended for high-speed automotive applications (up to 1 MBd). The device provides differential transmit capability to the bus and differential receive capability to the CAN controller. It is fully compatible with the “ISO 11898” standard. A current limiting circuit protects the transmitter output stage against short-circuit to positive and negative battery voltage. Although the power dissipation is increased during this fault condition, this feature will prevent destruction of the transmitter output stage. If the junction temperature exceeds a value of approximately 160 °C, the limiting current of both transmitter outputs is decreased. Because the transmitter is responsible for the major part of the power dissipation, this will result in reduced power dissipation and hence a lower chip temperature. All other parts of the PCA82C250 will remain in operation. The thermal protection is needed, in particular, when a bus line is short-circuited. The CANH and CANL lines are also protected against electrical transients which may occur in an automotive environment. Pin 8 (Rs) allows three different modes of operation to be selected: High-speed, Slope control and Standby. For high-speed operation, the transmitter output transistors are simply switched on and off as fast as possible. In this mode, no measures are taken to limit the rise and fall slope. Use of a shielded cable is recommended to avoid RFI problems. The High-speed mode is selected by connecting pin 8 to ground. For lower speeds or shorter bus length, an unshielded twisted pair or a parallel pair of wires can be used for the bus. To reduce RFI, the rise and fall slope should be limited. The rise and fall slope can be programmed with a resistor connected from pin 8 to ground. The slope is proportional to the current output at pin 8. If a HIGH level is applied to pin 8, the circuit enters a low-current Standby mode. In this mode, the transmitter is switched off and the receiver is switched to a low current. If dominant bits are detected (differential bus voltage >0.9 V), RXD will be switched to a PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 3 of 17 PCA82C250 NXP Semiconductors CAN controller interface LOW level. The microcontroller should react to this condition by switching the transceiver back to normal operation (via pin 8). Because the receiver is slow in Standby mode, the first message will be lost. Table 4. Truth table of the CAN transceiver Supply TXD CANH CANL Bus state RXD 4.5 V to 5.5 V 0 HIGH LOW dominant 0 4.5 V to 5.5 V 1 (or floating) floating floating recessive 1 < 2 V (not powered) X[1] floating floating recessive X[1] 2 V < VCC < 4.5 V >0.75VCC floating floating recessive X[1] 2 V < VCC < 4.5 V X[1] floating if VRs > 0.75VCC floating if recessive VRs > 0.75VCC X[1] [1] X = don’t care. Table 5. Pin Rs summary Condition forced at pin Rs Mode Resulting voltage or current at pin Rs VRs > 0.75VCC Standby IRs < |10 µA| −10 µA < IRs < −200 µA Slope control 0.4VCC < VRs < 0.6VCC VRs < 0.3VCC High-speed IRs < −500 µA 9. Limiting values Table 6. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to pin 2; positive input current. Symbol Parameter Conditions Max Unit V VCC supply voltage −0.3 +9.0 Vn DC voltage at pins 1, 4, 5 and 8 −0.3 VCC + 0.3 V V6, 7 DC voltage at pins 6 and 7 0 V < VCC < 5.5 V; no time limit −8.0 +18.0 Vtrt transient voltage at pins 6 and 7 see Figure 8 −150 +100 V Tstg storage temperature −55 +150 °C Tamb ambient temperature Tvj Vesd V −40 +125 °C virtual junction temperature [1] −40 +150 °C electrostatic discharge voltage [2] −2000 +2000 V [3] −200 +200 V [1] In accordance with “IEC 60747-1”. An alternative definition of virtual junction temperature is: Tvj = Tamb + Pd × Rth(vj-a), where Rth(j-a) is a fixed value to be used for the calculation of Tvj. The rating for Tvj limits the allowable combinations of power dissipation (Pd) and ambient temperature (Tamb). [2] Classification A: human body model; C = 100 pF; R = 1500 Ω; V = ±2000 V. [3] Classification B: machine model; C = 200 pF; R = 25 Ω; V = ±200 V. PCA82C250_6 Product data sheet Min © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 4 of 17 PCA82C250 NXP Semiconductors CAN controller interface 10. Thermal characteristics Table 7. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient in free air 160 K/W 11. Characteristics Table 8. Characteristics VCC = 4.5 to 5.5 V; Tamb = −40 to +125 °C; RL = 60 Ω; I8 > −10 µA; unless otherwise specified; all voltages referenced to ground (pin 2); positive input current; all parameters are guaranteed over the ambient temperature range by design, but only 100 % tested at +25 °C. Symbol Parameter Conditions Min Typ Max Unit Supply I3 supply current dominant; V1 = 1 V - - 70 mA recessive; V1 = 4 V; R8 = 47 kΩ - - 14 mA - - 18 mA - 100 170 µA recessive; V1 = 4 V; V8 = 1 V Standby; Tamb < 90 °C [1] DC bus transmitter VIH HIGH-level input voltage output recessive 0.7VCC - VCC + 0.3 V VIL LOW-level input voltage output dominant −0.3 - 0.3VCC V IIH HIGH-level input current V1 = 4 V −200 - +30 µA IIL LOW-level input current V1 = 1 V −100 - −600 µA V6,7 recessive bus voltage V1 = 4 V; no load 2.0 - 3.0 V ILO off-state output leakage current −2 V < (V6,V7) < 7 V −2 - +1 mA −5 V < (V6,V7) < 18 V −5 - +12 mA V7 CANH output voltage V1 = 1 V 2.75 - 4.5 V V6 CANL output voltage V1 = 1 V 0.5 - 2.25 V ∆V6, 7 difference between output voltage at pins 6 and 7 V1 = 1 V 1.5 - 3.0 V V1 = 1 V; RL = 45 Ω; VCC ≥ 4.9 V 1.5 - - V V1 = 4 V; no load −500 - +50 mV V7 = −5 V; VCC ≤ 5 V - - −105 mA V7 = −5 V; VCC = 5.5 V - - −120 mA V6 = 18 V - - 160 mA Isc7 Isc6 short-circuit CANH current short-circuit CANL current DC bus receiver: V1 = 4 V; pins 6 and 7 externally driven; −2 V < (V6, V7) < 7 V; unless otherwise specified Vdiff(r) Vdiff(d) differential input voltage (recessive) differential input voltage (dominant) −1.0 - +0.5 V −7 V < (V6, V7) < 12 V; not Standby mode −1.0 - +0.4 V 0.9 - 5.0 V −7 V < (V6, V7) < 12 V; not Standby mode 1.0 - 5.0 V Vdiff(hys) differential input hysteresis see Figure 5 - 150 - mV VOH HIGH-level output voltage pin 4; I4 = −100 µA 0.8VCC - VCC V PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 5 of 17 PCA82C250 NXP Semiconductors CAN controller interface Table 8. Characteristics …continued VCC = 4.5 to 5.5 V; Tamb = −40 to +125 °C; RL = 60 Ω; I8 > −10 µA; unless otherwise specified; all voltages referenced to ground (pin 2); positive input current; all parameters are guaranteed over the ambient temperature range by design, but only 100 % tested at +25 °C. Symbol Parameter Conditions Min Typ Max VOL pin 4; I4 = 1 mA 0 - 0.2VCC V I4 = 10 mA 0 - 1.5 V CANH, CANL 5 - 25 kΩ 20 - 100 kΩ - - 20 pF - - 10 pF LOW-level output voltage Ri input resistance Rdiff differential input resistance Ci input capacitance Cdiff differential input capacitance CANH, CANL Unit Reference output reference output voltage Vref V8 = 1 V; −50 µA < I5 < 50 µA 0.45VCC - 0.55VCC V V8 = 4 V; −5 µA < I5 < 5 µA 0.4VCC - 0.6VCC V Timing (see Figure 4, Figure 6 and Figure 7 tbit bit time minimum; V8 = 1 V - - 1 µs tonTXD delay TXD to bus active V8 = 1 V - - 50 ns toffTXD delay TXD to bus inactive V8 = 1 V - 40 80 ns tonRXD delay TXD to receiver active V8 = 1 V - 55 120 ns toffRXD delay TXD to receiver inactive V8 = 1 V; VCC < 5.1 V; Tamb < +85 °C - 82 150 ns V8 = 1 V; VCC < 5.1 V; Tamb < +125 °C - 82 170 ns tonRXD toffRXD delay TXD to receiver active delay TXD to receiver inactive V8 = 1 V; VCC < 5.5 V; Tamb < +85 °C - 90 170 ns V8 = 1 V; VCC < 5.5 V; Tamb < +125 °C - 90 190 ns R8 = 47 kΩ - 390 520 ns R8 = 24 kΩ - 260 320 ns R8 = 47 kΩ - 260 450 ns R8 = 24 kΩ - 210 320 ns R8 = 47 kΩ - 14 - V/µs |SR| differential output voltage slew rate tWAKE wake-up time from standby via pin 8 - - 20 µs tdRXDL bus dominant to RXD LOW V8 = 4 V; Standby mode - - 3 µs - - 0.3VCC V - - Standby/Slope Control (pin 8) V8 input voltage for high-speed I8 input current for high-speed −500 µA Vstb input voltage for standby mode 0.75VCC - - V Islope slope control mode current −10 - −200 µA Vslope slope control mode voltage 0.4VCC - 0.6VCC V [1] V8 = 0 V I1 = I4 = I5 = 0 mA; 0 V < V6 < VCC; 0 V < V7 < VCC; V8 = VCC. PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 6 of 17 PCA82C250 NXP Semiconductors CAN controller interface +5 V 100 pF VCC TXD CANH PCA82C250 62 Ω Vref 100 pF CANL RXD Rs GND 30 pF Rext mka671 Fig 3. Test circuit for dynamic characteristics. VCC VTXD 0V 0.9 V Vdiff 0.5 V 0.7VCC VRXD 0.3VCC tonTXD toffTXD tonRXD Fig 4. toffRXD mka672 Timing diagram for dynamic characteristics. VRXD HIGH LOW hysteresis 0.5 V Fig 5. Vdiff mka673 Hysteresis. PCA82C250_6 Product data sheet 0.9 V © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 7 of 17 PCA82C250 NXP Semiconductors CAN controller interface VCC VRs 0V VRXD tWAKE mka674 V1 = 1 V. Fig 6. Timing diagram for wake-up from Standby. 1.5 V Vdiff 0V VRXD tdRXDL mka675 V1 = 4 V; V8 = 4 V. Fig 7. Timing diagram for bus dominant to RXD LOW. +5 V VCC 1 nF TXD CANH PCA82C250 SCHAFFNER GENERATOR 62 Ω RXD 1 nF CANL Vref GND Rs Rext mka676 The waveforms of the applied transients shall be in accordance with “ISO 7637 part 1”, test pulses 1, 2, 3a and 3b. Fig 8. Test circuit for automotive transients. PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 8 of 17 PCA82C250 NXP Semiconductors CAN controller interface 12. Application information P8xC592/P8xCE598 CAN-CONTROLLER CTX0 CRX0 CRX1 PX,Y Rext +5 V TXD RXD Vref Rs VCC PCA82C250T 100 nF CAN-TRANSCEIVER GND CANH CANL CAN BUS LINE 124 Ω 124 Ω mka677 Fig 9. Application of the CAN transceiver. SJA1000 CAN-CONTROLLER TX0 TX1 RX0 RX1 6.8 kΩ 3.6 kΩ +5 V 390 Ω 100 nF 390 Ω VDD VSS 6N137 0V 100 nF 390 Ω 6N137 +5 V 390 Ω +5 V TXD RXD Vref Rs +5 V VCC PCA82C250 100 nF CAN-TRANSCEIVER Rext GND CANH CANL 124 Ω CAN BUS LINE 124 Ω mka678 Fig 10. Application with galvanic isolation. PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 9 of 17 PCA82C250 NXP Semiconductors CAN controller interface VCC 3 TXD Rs RXD 1 8 4 7 CANH PCA82C250 Vref 5 6 CANL 2 GND mka679 Fig 11. Internal pin configuration. PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 10 of 17 PCA82C250 NXP Semiconductors CAN controller interface 13. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index θ Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 inches 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.05 0.01 0.01 0.004 0.028 0.012 0.244 0.039 0.028 0.041 0.228 0.016 0.024 θ 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 12. Package outline SOT96-1 (SO8) PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 11 of 17 PCA82C250 NXP Semiconductors CAN controller interface 14. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 14.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 14.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 14.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 12 of 17 PCA82C250 NXP Semiconductors CAN controller interface 14.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 13) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 9 and 10 Table 9. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 Table 10. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 13. PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 13 of 17 PCA82C250 NXP Semiconductors CAN controller interface temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 13. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 14 of 17 PCA82C250 NXP Semiconductors CAN controller interface 15. Revision history Table 11. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA82C250_6 20090326 Product data sheet - PCA82C250_5 Modifications: • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • • Legal texts have been adapted to the new company name where appropriate. DIP8 package discontinued; bare die no longer available. PCA82C250_5 20000113 Product specification PCA82C250_3 19971021 Preliminary specification PCA82C250_2 PCA82C250_2 19940915 - PCA82C250_1 PCA82C250_1 19940408 - - PCA82C250_6 Product data sheet - PCA82C250_3 © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 15 of 17 PCA82C250 NXP Semiconductors CAN controller interface 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] PCA82C250_6 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 06 — 26 March 2009 16 of 17 PCA82C250 NXP Semiconductors CAN controller interface 18. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Thermal characteristics. . . . . . . . . . . . . . . . . . . 5 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Application information. . . . . . . . . . . . . . . . . . . 9 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Soldering of SMD packages . . . . . . . . . . . . . . 12 Introduction to soldering . . . . . . . . . . . . . . . . . 12 Wave and reflow soldering . . . . . . . . . . . . . . . 12 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 12 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 Legal information. . . . . . . . . . . . . . . . . . . . . . . 16 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 16 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Contact information. . . . . . . . . . . . . . . . . . . . . 16 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 26 March 2009 Document identifier: PCA82C250_6