LTC1416 Low Power 14-Bit, 400ksps Sampling ADC U DESCRIPTIO FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The LTC ®1416 is a 2.2µs, 400ksps, 14-bit sampling A/D converter that draws only 70mW from ±5V supplies. This easy-to-use device includes a high dynamic range sampleand-hold and a precision reference. Two digitally selectable power shutdown modes provide flexibility for low power systems. Sample Rate: 400ksps Power Dissipation: 70mW Guaranteed ± 1.5LSB DNL, ± 2LSB INL (Max) 80.5dB S/(N + D) and 93dB THD at 100kHz 80dB S/(N + D) and 90dB THD at Nyquist Nap and Sleep Shutdown Modes Operates with Internal or External Reference True Differential Inputs Reject Common Mode Noise 15MHz Full Power Bandwidth Sampling ±2.5V Bipolar Input Range 28-Pin SSOP Package The LTC1416’s full-scale input range is ±2.5V. Maximum DC specifications include ±2LSB INL, ±1.5LSB DNL over temperature. Outstanding AC performance includes 80.5dB S/(N + D) and 93dB THD with a 100kHz input, and 80dB S/(N + D) and 90dB THD at the Nyquist input frequency of 200kHz. UO APPLICATI ■ ■ ■ ■ ■ ■ S The unique differential input sample-and-hold can acquire single-ended or differential input signals up to its 15MHz bandwidth. The 60dB common mode rejection allows users to eliminate ground loops and common mode noise by measuring signals differentially from the source. Telecommunications Digital Signal Processing Multiplexed Data Acquisition Systems High Speed Data Acquisition Spectrum Analysis Imaging Systems The ADC has a µP compatible, 14-bit parallel output port. There is no pipeline delay in the conversion results. A separate convert start input and a data ready signal (BUSY) ease connections to FIFOs, DSPs and microprocessors. , LTC and LT are registered trademarks of Linear Technology Corporation. UO TYPICAL APPLICATI Effective Bits and Signal-to-(Noise + Distortion) vs Input Frequency Complete, 70mW, 14-Bit ADC with 80.5dB S/(N + D) 10µF DVDD AVDD OUTPUT BUFFERS 14-BIT ADC S/H AIN– REFCOMP 22µF BUFFER 4k TIMING AND LOGIC 2.5V REFERENCE VREF 1µF VSS 10µF –5V AGND DGND • • • D13 (MSB) D0 (LSB) BUSY CS CONVST RD SHDN 1416 TA01 EFFECTIVE BITS AIN+ 86 80 74 68 62 NYQUIST FREQUENCY SIGNAL/(NOISE + DISTORTION) (dB) LTC1416 14 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 fSAMPLE = 400kHz 1k 10k 100k INPUT FREQUENCY (Hz) 1M 2M 1416 TA02 1 LTC1416 W U U W W W AXI U U ABSOLUTE PACKAGE/ORDER I FOR ATIO RATI GS AVDD = DVDD = VDD (Notes 1, 2) ORDER PART NUMBER TOP VIEW Supply Voltage (VDD) ................................................ 6V Negative Supply Voltage (VSS)................................ – 6V Total Supply Voltage (VDD to VSS) .......................... 12V Analog Input Voltage (Note 3) ......................... (VSS – 0.3V) to (VDD + 0.3V) Digital Input Voltage (Note 4) ..........(VSS – 0.3V) to 10V Digital Output Voltage ....... (VSS – 0.3V) to (VDD + 0.3V) Power Dissipation ............................................. 500mW Operating Temperature Range Commercial ............................................ 0°C to 70°C Industrial ........................................... – 40°C to 85°C Storage Temperature Range ................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C AIN+ 1 28 AVDD AIN– 2 27 DVDD VREF 3 26 VSS REFCOMP 4 LTC1416CG LTC1416IG 25 BUSY AGND 5 24 CS D13(MSB) 6 23 CONVST D12 7 22 RD D11 8 21 SHDN D10 9 20 D0 D9 10 19 D1 D8 11 18 D2 D7 12 17 D3 D6 13 16 D4 DGND 14 15 D5 G PACKAGE 28-LEAD PLASTIC SSOP TJMAX = 110°C, θJA = 95°C/W Consult factory for Military grade parts and for A grade parts. U CO VERTER CHARACTERISTICS PARAMETER With Internal Reference (Notes 5, 6) CONDITIONS MIN Resolution (No Missing Codes) Integral Linearity Error (Note 7) Differential Linearity Error TYP ● ±0.8 ±2 LSB ● ±0.7 ±1.5 LSB ● ±5 ±20 LSB ±60 ±40 LSB LSB (Note 8) Full-Scale Error Internal Reference External Reference = 2.5V ±20 ±10 Full-Scale Tempco IOUT(REF) = 0 ±15 U U CONDITIONS VIN Analog Input Range (Note 9) 4.75V ≤ VDD ≤ 5.25V, – 5.25V ≤ VSS ≤ – 4.75V ● IIN Analog Input Leakage Current CS = High ● CIN Analog Input Capacitance Between Conversions During Conversions t ACQ Sample-and-Hold Acquisition Time (Note 9) t AP Sample-and-Hold Aperture Delay Time tjitter Sample-and-Hold Aperture Delay Time Jitter 2 ppm/°C (Note 5) SYMBOL PARAMETER CMRR UNITS Bits Offset Error A ALOG I PUT MAX 13 ● Analog Input Common Mode Rejection Ratio MIN TYP ±2.5 ● ±1 100 = AIN+ ) < 2.5V UNITS V 15 5 –1.5 – 2.5V < (AIN– MAX µA pF pF 400 ns ns 2 psRMS 60 dB LTC1416 W U DY A IC ACCURACY (Note 5) SYMBOL PARAMETER CONDITIONS S/(N + D) Signal-to-(Noise + Distortion) Ratio 100kHz Input Signal 200kHz Input Signal ● MIN TYP 77 80.5 80 THD Total Harmonic Distortion 100kHz Input Signal, First 5 Harmonics 200kHz Input Signal, First 5 Harmonics ● – 93 – 90 – 86 dB dB SFDR Spurious-Free Dynamic Range 100kHz Input Signal ● – 95 – 86 dB IMD Intermodulation Distortion fIN1 = 87.01172kHz, fIN2 = 113.18359kHz – 90 15 MHz (S/(N + D) ≥ 77dB) 0.8 MHz Full Power Bandwidth Full Linear Bandwidth U U U I TER AL REFERE CE CHARACTERISTICS MAX UNITS dB dB dB (Note 5) PARAMETER CONDITIONS MIN TYP MAX UNITS VREF Output Voltage IOUT = 0 2.480 2.500 2.520 V VREF Output Tempco IOUT = 0 ±15 ppm/°C VREF Line Regulation 4.75V ≤ VDD ≤ 5.25V – 5.25V ≤ VSS ≤ – 4.75V 0.05 0.05 LSB/V LSB/V VREF Output Resistance – 0.1mA ≤ IOUT ≤ 0.1mA COMP Output Voltage IOUT = 0 U U DIGITAL I PUTS A D DIGITAL OUTPUTS 4 kΩ 4.06 V (Note 5) SYMBOL PARAMETER CONDITIONS VIH High Level Input Voltage VDD = 5.25V ● VIL Low Level Input Voltage VDD = 4.75V ● 0.8 V IIN Digital Input Current VIN = 0V to VDD ● ±10 µA CIN Digital Input Capacitance VOH High Level Output Voltage VOL Low Level Output Voltage MIN VDD = 4.75V IOUT = – 10µA IOUT = – 200µA ● VDD = 4.75V IOUT = 160µA IOUT = 1.6mA ● TYP MAX 2.4 UNITS V 5 pF 4.5 V V 4.0 0.05 0.10 0.4 V V IOZ Hi-Z Output Leakage D13 to D0 VOUT = 0V to VDD, CS High ● ±10 µA COZ Hi-Z Output Capacitance D13 to D0 CS High (Note 9 ) ● 15 pF ISOURCE Output Source Current VOUT = 0V – 10 mA ISINK Output Sink Current VOUT = VDD 10 mA U W POWER REQUIRE E TS (Note 5) SYMBOL PARAMETER CONDITIONS VDD Positive Supply Voltage (Note 10) 4.75 5.25 V VSS Negative Supply Voltage (Note 10) – 4.75 – 5.25 V IDD Positive Supply Current Nap Mode Sleep Mode SHDN = 0V, CS = 0V SHDN = 0V, CS = 5V Negative Supply Current Nap Mode Sleep Mode SHDN = 0V, CS = 0V SHDN = 0V, CS = 5V ISS MIN TYP MAX UNITS ● 7 0.8 1 10 1.2 mA mA µA ● 7 20 15 10 mA µA µA 3 LTC1416 U W POWER REQUIRE E TS (Note 5) SYMBOL PARAMETER CONDITIONS PDISS Power Dissipation Power Dissipation, Nap Mode Power Dissipation, Sleep Mode SHDN = 0V, CS = 0V SHDN = 0V, CS = 5V WU TI I G CHARACTERISTICS MIN ● TYP MAX UNITS 70 4 0.1 100 6 mW mW mW TYP MAX UNITS (Note 5, see Figures 15 to 21) SYMBOL PARAMETER fSAMPLE(MAX) Maximum Sampling Frequency CONDITIONS tCONV Conversion Time tACQ Acquisition Time tACQ+CONV Acquisition + Conversion Time t1 CS to RD Setup Time (Notes 9, 10) ● 0 ns t2 CS↓ to CONVST↓ Setup Time (Notes 9, 10) ● 10 ns t3 CS↓ to SHDN↓ Setup Time (Notes 9, 10) ● 10 ns t4 SHDN↑ to CONVST↓ Wake-Up Time (Note 10) t5 CONVST Low Time (Notes 10, 11) ● 40 t6 CONVST to BUSY Delay CL = 25pF (Note 9) MIN ● 400 ● 1.5 kHz 1.9 2.2 µs ● 100 400 ns ● 2 2.5 µs 400 ns 25 50 ● t7 Data Ready Before BUSY↑ t8 Delay Between Conversions t9 Wait Time RD↓ After BUSY↑ t10 Data Access Time After RD↓ (Note 10) 75 50 ● 40 ns ● –5 ns CL = 25pF 100 CL = 100pF 0°C ≤ TA ≤ 70°C – 40°C ≤ TA ≤ 85°C ● ● ns ns 15 25 35 ns ns 20 35 50 ns ns 8 20 25 30 ns ns ns ● Bus Relinquish Time ns ns ● ● t11 ns t12 RD Low Time ● t 10 ns t13 CONVST High Time ● 40 ns The ● denotes specifications which apply over the full operating temperature range; all other limits and typicals at TA = 25°C. Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: All voltage values are with respect to ground with DGND and AGND wired together unless otherwise noted. Note 3: When these pin voltages are taken below VSS or above VDD, they will be clamped by internal diodes. This product can handle input currents greater than 100mA below VSS or above VDD without latchup. Note 4: When these pin voltages are taken below VSS, they will be clamped by internal diodes. This product can handle input currents greater than 100mA below VSS without latchup. These pins are not clamped to VDD. Note 5: VDD = 5V, VSS = – 5V, fSAMPLE = 400kHz, t r = t f = 5ns unless otherwise specified. 4 Note 6: Linearity, offset and full-scale specifications apply for a singleended AIN+ input with AIN– grounded. Note 7: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 8: Bipolar offset is the offset voltage measured from – 0.5LSB when the output code flickers between 0000 0000 0000 00 and 1111 1111 1111 11. Note 9: Guaranteed by design, not subject to test. Note 10: Recommended operating conditions. Note 11: The falling CONVST edge starts a conversion. If CONVST returns high at a critical point during the conversion it can create small errors. For best results ensure that CONVST returns high either within 900ns after the start of the conversion or after BUSY rises. LTC1416 U W TYPICAL PERFORMANCE CHARACTERISTICS S/(N + D) vs Input Frequency and Amplitude AMPLITUDE (dB BELOW THE FUNDAMENTAL) VIN = 0dB 80 80 70 VIN = –20dB 60 50 40 30 VIN = –60dB 20 70 60 50 40 30 20 10 10 0 0 1k 10k 100k INPUT FREQUENCY (Hz) 1k 1M 2M 10k 100k INPUT FREQUENCY (Hz) Spurious-Free Dynamic Range vs Input Frequency –20 –30 –40 –50 –60 –70 –80 –90 1M 2M 1k –50 –60 –70 10k 100k INPUT FREQUENCY (Hz) 1M 2M 1416 G03 Differential Nonlinearity vs Output Code 1.0 VOUT = ±2.5V VREF = 2.5V 0.5 –40 DNL ERROR (LSB) –20 –40 2ND –110 fSAMPLE = 400kHz fa=87.01171876kHz fb=113.1835938kHz –20 –30 3RD THD –100 0 –10 AMPLITUDE (dB) SPURIOUS-FREE DYNAMIC RANGE (dB) –10 Intermodulation Distortion Plot 0 –60 –80 –100 0 –0.5 –80 –120 –90 –100 1k 10k 100k INPUT FREQUENCY (Hz) 1M 2M –140 0 20 40 60 80 100 120 140 160 180 200 FREQUENCY (Hz) 1416 G04 –1.0 0 –0.5 –20 –30 –40 –50 –60 –70 –80 4096 8192 12288 16384 OUTPUT CODE 1416 G07 16384 80 –10 DGND (VIN = 100mV) VSS (VIN = 10mV) –90 –100 0 12288 Input Common Mode Rejection vs Input Frequency COMMON MODE REJECTION (dB) AMPLITUDE OF POWER SUPPLY FEEDTHROUGH (dB) 0.5 8192 1416 G06 Power Supply Feedthrough vs Ripple Frequency VOUT = ±2.5V VREF = 2.5V 4096 OUTPUT CODE 0 1.0 0 1416 G05 Integral Nonlinearity vs Output Code –1.0 0 1416 G02 1416 G01 INL ERROR (LSB) Distortion vs Input Frequency 90 SIGNAL-TO-NOISE RATIO (dB) SIGNAL/(NOISE + DISTORTION) (dB) 90 Signal-to-Noise Ratio vs Input Frequency VDD (VIN = 10mV) 70 60 50 40 30 20 10 0 1k 10k 100k RIPPLE FREQUENCY (Hz) 1M 2M 1416 G08 1k 10k 100k INPUT FREQUENCY (Hz) 1M 2M 1416 G09 5 LTC1416 U U U PI FU CTIO S AIN+ (Pin 1): ±2.5V Positive Analog Input. AIN– (Pin 2): ±2.5V Negative Analog Input. VREF (Pin 3): 2.5V Reference Output. Bypass to AGND with 1µF. REFCOMP (Pin 4): 4.06V Reference Output. Bypass to AGND with 22µF tantalum in parallel with 0.1µF ceramic, or 22µF ceramic. AGND (Pin 5): Analog Ground. D13 to D6 (Pins 6 to 13): Three-State Data Outputs. DGND (Pin 14): Digital Ground for Internal Logic. Tie to AGND. D5 to D0 (Pins 15 to 20): Three-State Data Outputs. SHDN (Pin 21): Power Shutdown Input. Low selects shutdown. Shutdown mode selected by CS. CS = 0 for nap mode and CS = 1 for sleep mode. RD (Pin 22): Read Input. This enables the output drivers when CS is low. CONVST (Pin 23): Conversion Start Signal. This active low signal starts a conversion on its falling edge. CS (Pin 24): The Chip Select input must be low for the ADC to recognize CONVST and RD inputs. CS also sets the shutdown mode when SHDN goes low. CS and SHDN low select the quick wake-up nap mode. CS high and SHDN low select sleep mode. BUSY (Pin 25): The BUSY output shows the converter status. It is low when a conversion is in progress. Data is valid on the rising edge of BUSY. VSS (Pin 26): – 5V Negative Supply. Bypass to AGND with 10µF tantalum in parallel with 0.1µF ceramic, or 10µF ceramic. DVDD (Pin 27): 5V Positive Supply. Tie to Pin 28. AVDD (Pin 28): 5V Positive Supply. Bypass to AGND with 10µF tantalum in parallel with 0.1µF ceramic, or 10µF ceramic. U U W FU CTIO AL BLOCK DIAGRA CSAMPLE AIN+ AVDD DVDD CSAMPLE AIN– VSS 4k VREF ZEROING SWITCHES 2.5V REF + REF AMP COMP 14-BIT CAPACITIVE DAC – REFCOMP (4.06V) SUCCESSIVE APPROXIMATION REGISTER AGND DGND INTERNAL CLOCK OUTPUT LATCHES • • • D13 D0 CONTROL LOGIC SHDN CONVST 6 14 RD CS BUSY 1416 BD LTC1416 TEST CIRCUITS Load Circuits for Access Timing Load Circuits for Output Float Delay 5V 5V 1k 1k DBN DBN DBN 1k CL 1k CL (A) Hi-Z TO VOH AND VOL TO VOH DBN (B) Hi-Z TO VOL AND VOH TO VOL (A) VOH TO Hi-Z 100pF 100pF (B) VOL TO Hi-Z 1416 TC02 1416 TC01 U U W U APPLICATIONS INFORMATION CONVERSION DETAILS The LTC1416 uses a successive approximation algorithm and an internal sample-and-hold circuit to convert an analog signal to a 14-bit parallel output. The ADC is complete with a precision reference and an internal clock. The control logic provides easy interface to microprocessors and DSPs. (Please refer to the Digital Interface section for the data format.) AIN+ CSAMPLE+ SAMPLE HOLD AIN– CSAMPLE– SAMPLE HOLD HOLD ZEROING SWITCHES CDAC+ HOLD + VDAC+ CDAC– COMP – VDAC– 14 SAR OUTPUT LATCH • • • D13 D0 1416 F01 Figure 1. Simplified Block Diagram Conversion start is controlled by the CS and CONVST inputs. At the start of the conversion the successive approximation register (SAR) is reset. Once a conversion cycle has begun, it cannot be restarted. During the conversion, the internal differential 14-bit capacitive DAC output is sequenced by the SAR from the most significant bit (MSB) to the least significant bit (LSB). Referring to Figure 1, the AIN+ and AIN– inputs are connected to the sample-and-hold capacitors (CSAMPLE) during the acquire phase and the comparator offset is nulled by the zeroing switches. In this acquire phase, a minimum delay of 400ns will provide enough time for the sample-and-hold capacitors to acquire the analog signal. During the convert phase the comparator zeroing switches open, putting the comparator into compare mode. The input switches connect the CSAMPLE capacitors to ground, transferring the differential analog input charge onto the summing junction. This input charge is successively compared with the binary-weighted charges supplied by the differential capacitive DAC. Bit decisions are made by the high speed comparator. At the end of a conversion, the differential DAC output balances the AIN+ and AIN– input charges. The SAR contents (a 14-bit data word) which represents the difference of AIN+ and AIN– are loaded into the 14-bit output latches. 7 LTC1416 U W U U APPLICATIONS INFORMATION DYNAMIC PERFORMANCE Signal-to-Noise Ratio The LTC1416 has excellent high speed sampling capability. FFT (Fast Fourier Transform) test techniques are used to test the ADC’s frequency response, distortion and noise at the rated throughput. By applying a low distortion sine wave and analyzing the digital output using an FFT algorithm, the ADC’s spectral content can be examined for frequencies outside the fundamental. Figure 2 shows a typical LTC1416 FFT plot. The Signal-to-Noise plus Distortion Ratio [S/(N + D)] is the ratio between the RMS amplitude of the fundamental input frequency to the RMS amplitude of all other frequency components at the A/D output. The output is band limited to frequencies from above DC and below half the sampling frequency. Figure 2a shows a typical spectral content with a 400kHz sampling rate and a 100kHz input. The dynamic performance is excellent for input frequencies up to and beyond the Nyquist limit of 200kHz, Figure 2b. 0 fSAMPLE = 400kHz fIN = 101.5625kHz SFDR = 95.2dB SINAD = 80.5dB AMPLITUDE (dB)) –20 –40 Effective Number of Bits The Effective Number of Bits (ENOBs) is a measurement of the resolution of an ADC and is directly related to the S/(N + D) by the equation: –60 –80 ENOB = [S/(N + D) – 1.76]/6.02 –100 –120 –140 0 25 50 75 100 125 150 175 200 FREQUENCY (kHz) 1416 F02a where ENOB is the Effective Number of Bits of resolution and S/(N + D) is expressed in dB. At the maximum sampling rate of 400kHz the LTC1416 maintains near ideal ENOBs up to the Nyquist input frequency of 200kHz (refer to Figure 3). Figure 2a. LTC1416 Nonaveraged, 4096 Point FFT, Input Frequency = 100kHz AMPLITUDE (dB)) –20 –40 EFFECTIVE BITS fSAMPLE = 400kHz fIN = 189.9414kHz SFDR = 94.8dB SINAD = 80.2dB –60 –80 –100 –120 0 25 50 100 125 150 175 200 FREQUENCY (kHz) 75 1416 F02b Figure 2b. LTC1416 Nonaveraged, 4096 Point FFT, Input Frequency = 190kHz 8 NYQUIST FREQUENCY fSAMPLE = 400kHz 1k –140 86 80 74 68 62 SIGNAL/(NOISE + DISTORTION) (dB) 0 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 10k 100k INPUT FREQUENCY (Hz) 1M 2M 1416 TA02 Figure 3. Effective Bits and Signal/(Noise + Distortion) vs Input Frequency LTC1416 U U W U APPLICATIONS INFORMATION Total Harmonic Distortion (THD) is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency. THD is expressed as: THD = 20 log V22 + V32 + V42 + ...Vn2 V1 where V1 is the RMS amplitude of the fundamental frequency and V2 through Vn are the amplitudes of the second through Nth harmonics. THD versus input frequency is shown in Figure 4. The LTC1416 has good distortion performance up to the Nyquist frequency and beyond. ence frequencies of mfa ± nfb, where m and n = 0, 1, 2, 3, etc. For example, the 2nd order IMD terms include (fa + fb). If the two input sine waves are equal in magnitude, the value (in decibels) of the 2nd order IMD products can be expressed by the following formula: ( ) IMD fa + fb = 20 log ( ) Amplitude at fa + fb Amplitude at fa 0 –20 AMPLITUDE (dB) Total Harmonic Distortion fSAMPLE = 400kHz fa=87.01171876kHz fb=113.1835938kHz –40 –60 –80 AMPLITUDE (dB BELOW THE FUNDAMENTAL) –100 0 –120 –10 –20 –140 0 20 40 60 80 100 120 140 160 180 200 FREQUENCY (Hz) –30 –40 1416 G05 –50 –60 Figure 5. Intermodulation Distortion Plot –70 –80 –90 3RD THD Peak Harmonic or Spurious Noise 2ND –100 –110 1k 10k 100k INPUT FREQUENCY (Hz) 1M 2M 1416 G03 Figure 4. Distortion vs Input Frequency Intermodulation Distortion If the ADC input signal consists of more than one spectral component, the ADC transfer function nonlinearity can produce intermodulation distortion (IMD) in addition to THD. IMD is the change in one sinusoidal input caused by the presence of another sinusoidal input at a different frequency. If two pure sine waves of frequencies fa and fb are applied to the ADC input, nonlinearities in the ADC transfer function can create distortion products at the sum and differ- The peak harmonic or spurious noise is the largest spectral component excluding the input signal and DC. This value is expressed in decibels relative to the RMS value of a full-scale input signal. Full-Power and Full-Linear Bandwidth The full-power bandwidth is that input frequency at which the amplitude of the reconstructed fundamental is reduced by 3dB for a full-scale input signal. The full-linear bandwidth is the input frequency at which the S/(N + D) has dropped to 77dB (12.5 effective bits). The LTC1416 has been designed to optimize input bandwidth, allowing the ADC to undersample input signals with frequencies above the converter’s Nyquist frequency. The noise floor stays very low at high frequencies; S/(N + D) becomes dominated by distortion at frequencies far beyond Nyquist. 9 LTC1416 U W U U APPLICATIONS INFORMATION Driving the Analog Input The differential analog inputs of the LTC1416 are easy to drive. The inputs may be driven differentially or as a singleended input (i.e., the AIN– input is grounded). The AIN+ and AIN– inputs are sampled at the same instant. Any unwanted signal that is common mode to both inputs will be reduced by the common mode rejection of the sampleand-hold circuit. The inputs draw only one small current spike while charging the sample-and-hold capacitors at the end of conversion. During conversion the analog inputs draw only a small leakage current. If the source impedance of the driving circuit is low, then the LTC1416 inputs can be driven directly. As source impedance increases so will acquisition time (see Figure 6). For minimum acquisition time, with high source impedance, a buffer amplifier should be used. The only requirement is that the amplifier driving the analog input(s) must settle after the small current spike before the next conversion starts (settling time must be 400ns for full throughput rate). ACQUISITION TIME (µs) The best choice for an op amp to drive LTC1416 will depend on the application. Generally, applications fall into two categories: AC applications where dynamic specifications are most critical and time domain applications where DC accuracy and settling time are most critical. The following list is a summary of the op amps that are suitable for driving the LTC1416. More detailed information is available in the Linear Technology Databooks and the LinearViewTM CD-ROM. LT ®1220: 30MHz unity-gain bandwidth voltage feedback amplifier. ±5V to ±15V supplies, excellent DC specifications. LT1223: 100MHz video current feedback amplifier. 6mA supply current, ±5V to ±15V supplies, low distortion at frequencies above 400kHz, low noise, good for AC applications. 10 1 LT1227: 140MHz video current feedback amplifier. 10mA supply current, ±5V to ±15V supplies, lowest distortion at frequencies above 400kHz, low noise, best for AC applications. 0.1 0.01 10 frequency. For example, if an amplifier is used in a gain of 1 and has a unity-gain bandwidth of 50MHz, then the output impedance at 50MHz should be less than 100Ω. The second requirement is that the closed-loop bandwidth must be greater than 10MHz to ensure adequate smallsignal settling for full throughput rate. If slower op amps are used, more settling time can be provided by increasing the time between conversions. 100 1k 10k SOURCE RESISTANCE (Ω) 100k LT1229/LT1230: Dual and quad 100MHz current feedback amplifiers. ±2V to ±15V supplies, low noise, good AC specs, 6mA supply current each amplifier. 1416 F06 Figure 6. Acquisition Time vs Source Resistance Choosing an Input Amplifier Choosing an input amplifier is easy if a few requirements are taken into consideration. First, to limit the magnitude of the voltage spike seen by the amplifier from charging the sampling capacitor, choose an amplifier that has a low output impedance (<100Ω) at the closed-loop bandwidth 10 LT1360: 50MHz voltage feedback amplifier. 3.8mA supply current, good AC and DC specs, ±5V to ±15V supplies. LT1363: 70MHz, 1000V/µs op amps. 6.3mA supply current, good AC and DC specs. LT1364/LT1365: Dual and quad 70MHz, 100V/µs op amps. 6.3mA supply current per amplifier. LinearView is a trademark of Linear Technology Corporation. LTC1416 U U W U APPLICATIONS INFORMATION Input Filtering The noise and the distortion of the input amplifier and other circuitry must be considered since they will add to the LTC1416 noise and distortion. The small-signal bandwidth of the sample-and-hold circuit is 15MHz. Any noise or distortion products that are present at the analog inputs will be summed over this entire bandwidth. Noisy input circuitry should be filtered prior to the analog inputs to minimize noise. A simple 1-pole RC filter is sufficient for many applications. For example, Figure 7 shows a 1000pF capacitor from AIN+ to ground and a 200Ω source resistor to limit the input bandwidth to 800kHz. The 1000pF capacitor also acts as a charge reservoir for the input sample-and-hold and isolates the ADC input from sampling glitch sensitive circuitry. High quality capacitors and resistors should be used since these components can add distortion. NPO and silver mica type dielectric capacitors have excellent linearity. Carbon surface mount resistors can also generate distortion from self-heating and from damage that may occur during soldering. Metal film surface mount resistors are much less susceptible to both problems. ANALOG INPUT 200Ω 1000pF 1 AIN+ 2 AIN– 3 4 22µF 5 accommodate other input ranges often with little or no additional circuitry. The following sections describe the reference and input circuitry and how they affect the input range. Internal Reference The LTC1416 has an on-chip, temperature compensated, curvature corrected, bandgap reference that is factory trimmed to 2.500V. It is connected internally to a reference amplifier and is available at VREF (Pin 3). See Figure 8a. A 4k resistor is in series with the output so that it can be easily overdriven by an external reference or other circuitry (see Figure 8b). The reference amplifier gains the voltage at the VREF pin by 1.625 to create the required internal reference voltage. This provides buffering between the VREF pin and the high speed capacitive DAC. The 2.5V 4.0625V 3 VREF 4 REFCOMP R1 4k BANDGAP REFERENCE REF AMP R2 80k 22µF 5 LTC1416 AGND R3 128k LTC1416 VREF 1416 F08a REFCOMP Figure 8a. LTC1416 Reference Circuit AGND 1416 F07 Figure 7. RC Input Filter 5V VIN Input Range The ±2.5V input range of the LTC1416 is optimized for low noise and low distortion. Most op amps also perform best over this same range, allowing direct coupling to the analog inputs and eliminating the need for special translation circuitry. Some applications may require other input ranges. The LTC1416 differential inputs and reference circuitry can ANALOG INPUT LT1019A-2.5 VOUT 1 AIN+ 2 AIN– 3 4 22µF 5 LTC1416 VREF REFCOMP AGND 1416 F08b Figure 8b. Using the LT1019-2.5 as an External Reference 11 LTC1416 U U W U APPLICATIONS INFORMATION The VREF pin can be driven with a DAC or other means shown in Figure 9. This is useful in applications where the peak input signal amplitude may vary. The input span of the ADC can then be adjusted to match the peak input signal, maximizing the signal-to-noise ratio. The filtering of the internal LTC1416 reference amplifier will limit the bandwidth and settling time of this circuit. A settling time of 5ms should be allowed for after a reference adjustment. LTC1450 1 ANALOG INPUT AIN+ 2 AIN– 1.25V TO 3V 3 4 22µF 5 80 COMMON MODE REJECTION (dB) reference amplifier compensation pin, REFCOMP (Pin 4), must be bypassed with a capacitor to ground. The reference amplifier is stable with capacitors of 1µF or greater. For the best noise performance, a 22µF ceramic or 22µF tantalum in parallel with a 0.1µF ceramic is recommended. 70 60 50 40 30 20 10 0 1k 10k 100k INPUT FREQUENCY (Hz) 1416 G09 Figure 10a. CMRR vs Input Frequency ANALOG INPUT LTC1416 ±2.5V VREF 1 AIN+ 2 AIN– 3 0V TO 5V 4 REFCOMP 22µF AGND 5 VREF LTC1416 REFCOMP AGND 1416 F10b 1416 F09 Figure 9. Driving VREF with a DAC Differential Inputs The LTC1416 has a unique differential sample-and-hold circuit that allows rail-to-rail inputs. The ADC will always convert the difference of AIN+ – AIN– independent of the common mode voltage. The common mode rejection holds up to extremely high frequencies (see Figure 10a). The only requirement is that both inputs cannot exceed the AVDD or AVSS power supply voltages. Integral nonlinearity errors (INL) and differential nonlinearity errors (DNL) are independent of the common mode voltage, however, the bipolar zero error (BZE) will vary. The change in BZE is typically less than 0.1% of the common mode voltage. Dynamic performance is also affected by the common mode voltage. THD will degrade as the inputs approach either power supply rail, from 90dB with a common mode of 0V to 79dB with a common mode of 2.5V or – 2.5V. Differential inputs allow greater flexibility for accepting different input ranges. Figure 10b shows a circuit that 12 1M 2M Figure 10b. Selectable 0V to 5V or ±2.5V Input Range converts a 0V to 5V analog input signal with no additional translation circuitry. Full-Scale and Offset Adjustment Figure 11a shows the ideal input/output characteristics for the LTC1416. The code transitions occur midway between successive integer LSB values (i.e., – FS + 0.5LSB, – FS + 1.5LSB, – FS + 2.5LSB, . . . FS – 1.5LSB, FS – 0.5LSB). The output is two’s complement binary with 1LSB = FS – (– FS)/16384 = 5V/16384 = 305.2µV. In applications where absolute accuracy is important, offset and full-scale errors can be adjusted to zero. Offset error must be adjusted before full-scale error. Figure 11b shows the extra components required for full-scale error adjustment. Zero offset is achieved by adjusting the offset applied to the AIN– input. For zero offset error, apply – 152µV (i.e., – 0.5LSB) at AIN+ and adjust the offset at the AIN– input until the output code flickers between 0000 LTC1416 U W U U APPLICATIONS INFORMATION 0000 0000 00 and 1111 1111 1111 11. For full-scale adjustment, an input voltage of 2.499544V (FS/2 – 1.5LSB) is applied to AIN and R2 is adjusted until the output code flickers between 0111 1111 1111 10 and 0111 1111 1111 11. 011...111 OUTPUT CODE 011...110 000...001 000...000 111...111 111...110 100...001 BOARD LAYOUT AND BYPASSING 100...000 FS – 1LSB – (FS – 1LSB) INPUT VOLTAGE (AIN+ – AIN–) 1416 F11a Figure 11a. LTC1416 Transfer Characteristics –5V R3 24k R1 50k applications, however, do not have a –5V supply readily available and most ADCs have inadequate PSRR to sufficiently attenuate the noise created by a switching or charge pump supply. The LTC1416’s excellent PSRR makes it possible to achieve good performance, even at 14 bits, using a switch based regulator for a –5V supply. Figure 12a shows a circuit using an LT1373 configured as a Cuk converter creating –5V from a 5V supply. The circuit shown in Figure 12b uses an LT1054 regulated charge pump to provide –5V. This circuit has the advantage of reduced board space and fewer passive components. (For further details refer to Linear Technology Magazine, June 1997, Page 29.) ANALOG INPUT R4 100Ω 1 AIN+ 2 AIN– 3 R5 R2 47k 50k R6 24k 4 5 22µF LTC1416 VREF REFCOMP AGND 1416 F11b Figure 11b. Offset and Full-Scale Adjust Circuit Generating a – 5V Supply There are several advantages to using ±5V supplies rather than a single 5V supply. A larger signal magnitude is possible which increases the dynamic range and improves the signal-to-noise ratio. Operating on ±5V supplies also offers increased headroom which eases the requirements for signal conditioning circuitry, avoids the limitations of rail-to-rail operation and widens the selection of high performance operational amplifiers. Some Wire wrap boards are not recommended for high resolution or high speed A/D converters. To obtain the best performance from the LTC1416, a printed circuit board with ground plane is required. Layout for the printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital track alongside an analog signal track or underneath the ADC. The analog input should be screened by AGND. An analog ground plane separate from the logic system ground should be established under and around the ADC (see Figure 13). Pin 5 (AGND), Pins 14 and 19 (ADC’s DGND) and all other analog grounds should be connected to this single analog ground point. The REFCOMP bypass capacitor and the DVDD bypass capacitor should also be connected to this analog ground plane. No other digital grounds should be connected to this analog ground plane. Low impedance analog and digital power supply common returns are essential to low noise operation of the ADC and the foil width for these tracks should be as wide as possible. In applications where the ADC data outputs and control signals are connected to a continuously active microprocessor bus, it is possible to get errors in the conversion results. These errors are due to feedthrough from the microprocessor to the successive approximation comparator. The problem can be eliminated by forcing the microprocessor into a Wait state during conversion or by using three-state buffers to isolate the ADC data bus. The 13 LTC1416 U U W U APPLICATIONS INFORMATION 5V 1µF CER 1 AIN+ AVDD 2 AIN– DVDD VREF VSS 3 4 C5 5 6 7 8 9 10 11 12 13 14 COMP BUSY AGND CS D13 (MSB) CONVST D12 RD D11 SHDN D10 D0 LTC1416 D9 D1 D8 D2 D7 D3 D6 D4 DGND D5 2 L1 3 C7 1 –5V 28 27 26 CUK* CONVERTER 25 24 5 23 C8 22µF 10V TANT MICROPROCESSOR/ MICROCONTROLLER INTERFACE 22 21 + 4 7 6 VIN S/S C10 10µF CER VSW U2 LT1373 GND GND S 20 4 NFB VC 8 R4 4.99k 1% 3 1 C12 0.1µF D1 R3 4.99k 19 C9 0.01µF 18 C11 100µF 10V TANT + ANALOG INPUT C6 R5 4.99k 1% R6 499Ω 1% 1416 F12a 17 C5 =22 µF CERAMIC C6, C7 =10 µF CERAMIC L1 =OCTAPAC CTX-100-1 D1 =1N5818 16 15 Figure 12a. Using the LT1373 to Generate a – 5V Supply 5V –5V C6 ANALOG INPUT 1µF CER 1 AIN+ AVDD 2 AIN– DVDD 3 4 C5 5 6 7 8 9 10 11 12 13 14 VREF VSS BUSY COMP CS AGND D13 (MSB) CONVST D12 RD D11 SHDN D0 D10 LTC1416 D9 D1 D8 D2 D7 D3 D6 D4 DGND D5 28 C2 2µF 27 1 C7 26 2 25 C1 10µF TANT 24 23 22 + FB/SHDN V+ 7 OSC U1 LT1054 6 3 VREF GND 5 4 CAP – VOUT MICROPROCESSOR/ MICROCONTROLLER INTERFACE 20 19 18 17 C5 =22 µF CERAMIC C6, C7 =10 µF CERAMIC 15 Figure 12b. Using the LT1054 to Generate a – 5V Supply 14 8 + CAP+ 21 16 C4 100µF TANT R1, 30.1k C3 0.002µF R2, 120k 1416 F12b LTC1416 U U W U APPLICATIONS INFORMATION 1 AIN+ AIN– ANALOG INPUT CIRCUITRY + – 2 DIGITAL SYSTEM LTC1416 REFCOMP AGND 5 4 VSS 26 22µF 10µF AVDD DVDD DGND 28 27 14 10µF 1416 F13 Figure 13. Power Supply Grounding Practice. traces connecting the pins and bypass capacitors must be kept short and should be made as wide as possible. The LTC1416 has differential inputs to minimize noise coupling. Common mode noise on the AIN+ and AIN– leads will be rejected by the input CMRR. The AIN– input can be used as a ground sense for the AIN+ input; the LTC1416 will hold and convert the difference voltage between AIN+ and AIN– . The leads to AIN+ (Pin 1) and AIN– (Pin 2) should be kept as short as possible. In applications where this is not possible, the AIN+ and AIN– traces should be run side by side to equalize coupling. Supply Bypassing High quality, low series resistance ceramic, bypass capacitors should be used at the VDD (10µF) and REFCOMP (22µF) pins as shown in the Typical Application on the first page of this data sheet. Surface mount ceramic capacitors such as Murata GRM235Y5V106Z016 provide excellent bypassing in a small board space. Alternatively tantalum capacitors in parallel with 0.1µF ceramic capacitors can be used. Bypass capacitors must be located as close to the pins as possible. The traces connecting the pins and the bypass capacitors must be kept short and should be made as wide as possible. Example Layout Figures 14a, 14b, 14c and 14d show the schematic and layout of an evaluation board. The layout demonstrates the proper use of decoupling capacitors and ground plane with a 2-layer printed circuit board. DIGITAL INTERFACE The A/D converter is designed to interface with microprocessors as a memory mapped device. The CS and RD control inputs are common to all peripheral memory interfacing. A separate CONVST is used to initiate a conversion. Internal Clock The A/D converter has an internal clock that eliminates the need for synchronization between the external clock and the CS and RD signals found in other ADCs. The internal clock is factory trimmed to achieve a typical conversion time of 1.8µs, and a maximum conversion time over the full operating temperature range of 2.2µs. No external adjustments are required. The guaranteed maximum acquisition time is 400ns. In addition, a throughput time of 2.5µs and a minimum sampling rate of 400ksps is guaranteed. Power Shutdown The LTC1416 provides two power shutdown modes—nap mode and sleep mode to save power during inactive periods. The nap mode reduces the power by 95% and leaves only the digital logic and reference powered up. The wake-up time from nap to active is 200ns. In sleep mode the reference is shut down and only a small current of 120µA remains. Wake-up time from sleep mode is much slower since the reference circuit must power up and settle to 0.005% for full 14-bit accuracy. Sleep mode wake-up time is dependent on the value of the capacitor connected to the REFCOMP (Pin 4). The wake-up time is 20ms with the recommended 22µF capacitor. 15 CLK A– A+ VLOGIC JP5A JP5B JP5C 1 JP2 RD CS 2 C8 1µF 10V 3 3 HC14 U7B C11 1000pF R15 51Ω D15 SS12 R16 51Ω SHDN HC14 U7A JP4 DGND R19 51Ω R18 10k R17 10k VOUT GND TABGND 2 4 VIN LT1121-5 NOTES: UNLESS OTHERWISE SPECIFIED ALL RESISTOR VALUES IN OHMS, 5% J7 J5 AGND J2 J4 GND +VIN 1 U2 4 C2 22µF 10V VREF JP3 C13 22µF 10 V + VCC C4 0.1µF VSS R20 1M VCC C9 10µF 10V C3 0.1µF U3 LT1363 2 7 – 6 3 + 8 1 4 V– V+ VOUT VCC C12 0.1µF R14 20Ω + 14 5 26 27 28 21 22 23 24 25 4 3 2 1 U4 LTC1416 DATA READY DGND AGND VSS DVDD AVDD SHDN RD CONVST CS BUSY REFCOMP VREF AIN– AIN+ C10 10µF 10V B10 9 5 GND VOUT U7F 1 D7 D6 D5 D4 D3 D2 D1 D0 0E 6 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 U6 74HC574 R21 1k 12 13 14 15 16 17 18 19 12 13 14 15 16 17 18 19 D06 D07 D08 D09 D10 D11 D12 D13 D05 D04 D03 D02 D01 D00 11 U7E D13 D07 D06 D05 D04 D03 D02 D01 D00 D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01 D00 U7G HC14 GND 7 14 VCC HC14 12 HC14 C6 15pF 9 HC14 U7D HC14 8 10 RDY D13 D13 D12 D11 D10 D09 U7C 9 8 7 6 5 4 3 2 11 Q6 D6 D7 Q5 D5 Q7 Q4 Q3 Q2 Q1 Q0 D4 D3 D2 D1 D0 0E D[00:13] 20 B00 13 B06 B07 B08 B09 B10 B11 B12 8 9 7 B13 6 B04 B05 5 B03 4 3 B01 B02 2 5 1 11 U5 74HC574 C1 22µF 10V B00 D14 SS12 1 VSS D08 VLOGIC B[00:13] VIN U1 79L05 19 B01 18 B02 17 B03 16 B04 15 B05 13 B06 12 B07 11 B08 10 B09 B11 B12 8 B13 7 2 6 C15 0.1µF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 –VIN J1 –7V TO –15V Figure 14a. Suggested Evaluation Circuit Schematic C5 10µF 10V VSS C14 0.1µF VLOGIC D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 DGND HEADER 18-PIN DGND J6-18 RDY D13 D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01 D00 J6-17 J6-16 J6-15 J6-2 J6-1 J6-4 J6-3 J6-6 J6-5 J6-8 J6-7 J6-10 J6-9 J6-12 J6-11 J6-14 J6-13 R13, 1.2k D13 R12, 1.2k D12 R11, 1.2k D11 R10, 1.2k D10 R9, 1.2k R8, 1.2k R7, 1.2k R6, 1.2k R5, 1.2k R4, 1.2k R3, 1.2k R2, 1.2k R1, 1.2k R0, 1.2k 1416 F14a JP1 LED D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01 D00 U U 16 W J3 7V TO 15V APPLICATIONS INFORMATION U + VCC LTC1416 LTC1416 U W U U APPLICATIONS INFORMATION Figure 14b. Suggested Evaluation Circuit Board— Component Side Silkscreen Figure 14c. Suggested Evaluation Circuit Board— Component Side Layout CS t3 SHDN 1416 F15a Figure 15a. CS to SHDN Timing SHDN t3 CONVST 1416 F15b Figure 15b. SHDN to CONVST Wake-Up Timing Figure 14d. Suggested Evaluation Circuit Board— Solder Side Layout 17 LTC1416 U U W U APPLICATIONS INFORMATION Shutdown is controlled by Pin 21 (SHDN), the ADC is in shutdown when it is low. The shutdown mode is selected with Pin 20 (CS), low selects nap. starts the conversion and reads the output with the RD signal. Conversions are started by the MPU or DSP (no external sample clock). Timing and Control In slow memory mode the processor applies a logic low to RD (= CONVST), starting the conversion. BUSY goes low, forcing the processor into a Wait state. The previous conversion result appears on the data outputs. When the conversion is complete, the new conversion results appear on the data outputs; BUSY goes high releasing the processor, and the processor takes RD (= CONVST) back high and reads the new conversion data. Conversion start and data read operations are controlled by three digital inputs: CONVST, CS and RD. A logic “0” applied to the CONVST pin will start a conversion after the ADC has been selected (i.e., CS is low). Once initiated, it cannot be restarted until the conversion is complete. Converter status is indicated by the BUSY output. BUSY is low during a conversion. In ROM mode, the processor takes RD (= CONVST) low, starting a conversion and reading the previous conversion result. After the conversion is complete, the processor can read the new result and initiate another conversion. Figures 16 through 21 show several different modes of operation. In modes 1a and 1b (Figures 17 and 18) CS and RD are both tied low. The falling edge of CONVST starts the conversion. The data outputs are always enabled and data can be latched with the BUSY rising edge. Mode 1a shows operation with a narrow logic low CONVST pulse. Mode 1b shows a narrow logic high CONVST pulse. CS t2 In mode 2 (Figure 19) CS is tied low. The falling edge of CONVST signal again starts the conversion. Data outputs are in three-state until read by the MPU with the RD signal. Mode 2 can be used for operation with a shared MPU data bus. CONVST t1 RD 1416 F16 In slow memory and ROM modes (Figures 20 and 21), CS is tied low and CONVST and RD are tied together. The MPU Figure 16. CS to CONVST Setup Timing t CONV CS = RD = 0 (SAMPLE N) t5 CONVST t6 t8 BUSY t7 DATA DATA (N – 1) DB13 TO DB0 DATA N DB13 TO DB0 DATA (N + 1) DB13 TO DB0 1416 F17 Figure 17. Mode 1a. CONVST Starts a Conversion. Data Outputs Always Enabled (CONVST = 18 ) LTC1416 U U W U APPLICATIONS INFORMATION tCONV CS = RD = 0 t8 t5 t13 CONVST t6 t6 t6 BUSY t7 DATA (N – 1) DB13 TO DB0 DATA DATA N DB13 TO DB0 DATA (N + 1) DB13 TO DB0 1416 F18 Figure 18. Mode 1b. CONVST Starts a Conversion. Data Outputs Always Enabled (CONVST = ) t13 (SAMPLE N) tCONV t5 CS = 0 t8 CONVST t6 BUSY t9 t 12 t 11 RD t 10 DATA N DB13 TO DB0 DATA 1416 F19 Figure 19. Mode 2. CONVST Starts a Conversion. Data Is Read by RD t8 t CONV CS = 0 (SAMPLE N) RD = CONVST t6 t 11 BUSY t 10 DATA t7 DATA (N – 1) DB13 TO DB0 DATA N DB13 TO DB0 DATA N DB13 TO DB0 DATA (N + 1) DB13 TO DB0 1416 F20 Figure 20. Slow Memory Mode Timing Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTC1416 U U W U APPLICATIONS INFORMATION t CONV CS = 0 t8 (SAMPLE N) RD = CONVST t6 t 11 BUSY t 10 DATA N DB13 TO DB0 DATA (N – 1) DB13 TO DB0 DATA 1416 F21 Figure 21. ROM Mode Timing U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. G Package 28-Lead Plastic SSOP (0.209) (LTC DWG # 05-08-1640) 0.205 – 0.212** (5.20 – 5.38) 0.068 – 0.078 (1.73 – 1.99) 0.397 – 0.407* (10.07 – 10.33) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 0° – 8° 0.022 – 0.037 (0.55 – 0.95) 0.005 – 0.009 (0.13 – 0.22) 0.0256 (0.65) BSC *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 0.301 – 0.311 (7.65 – 7.90) 0.010 – 0.015 (0.25 – 0.38) 0.002 – 0.008 (0.05 – 0.21) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 G28 SSOP 0694 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1278/LTC1279 Single Supply, 12-Bit, 500ksps/600ksps ADCs Low Power, 5V or ±5V Supply LTC1400 High Speed Serial 12-Bit ADC 400ksps, Complete with VREF, CLK, Sample-and-Hold in SO-8 LTC1409 Low Power, 12-Bit, 800ksps Sampling ADC Best Dynamic Performance, fSAMPLE ≤ 800ksps, 80mW Dissipation LTC1410 12-Bit, 1.25Msps Sampling ADC with Shutdown Best Dynamic Performance, THD = 84dB and SINAD = 71dB at Nyquist LTC1412 12-Bit, 3Msps Sampling ADC Best Dynamic Performance, SINAD = 72dB at Nyquist LTC1415 Single 5V, 12-Bit, 1.25Msps ADC Single Supply, 55mW Dissipation LTC1418 14-Bit, 200ksps Sampling ADC 16mW Dissipation, Serial and Parallel Outputs LTC1419 14-Bit, 800ksps Sampling ADC with Shutdown 81.5dB SINAD, 150mW from ±5V Supplies LTC1604 16-Bit, 333ksps Sampling ADC ±2.5V Input, SINAD = 90dB, THD = 100dB LTC1605 Single 5V, 16-Bit, 100ksps ADC Low Power, ±10V Inputs 20 Linear Technology Corporation 1416f LT/TP 0598 4K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com LINEAR TECHNOLOGY CORPORATION 1997