AD ADSP-21469KBZ-ENG2

SHARC Processor
ADSP-21469/ADSP-21469W
Preliminary Technical Data
SUMMARY
Code compatible with all other members of the SHARC family
The ADSP-21469 is available with a 450 MHz core instruction
rate with unique audiocentric peripherals such as the digital applications interface, serial ports, precision clock
generators, S/PDIF transceiver, asynchronous sample rate
converters, input data port, and more.
For complete ordering information, see Ordering Guide on
Page 56.
Note: This datasheet is preliminary. This document contains
material that is subject to change without notice.
High performance 32-bit/40-bit floating point processor
optimized for high performance audio processing
Single-instruction, multiple-data (SIMD) computational
architecture
On-chip memory—5 Mbits of on-chip RAM
CORE PROCESSOR
THERMAL
DIODE
PLL
4 BLOCKS OF
ON-CHIP MEMORY
INSTRUCTION
CACHE
32 x 48-BIT
TIMER
JTAG TEST & EMULATION
5M BIT RAM
EXTERNAL PORT
8
DAG1
8 x 4 x 32
DAG2
8 x 4 x 32
ADDR
32
PROGRAM
SEQUENCER
PM ADDRESS BUS
DM ADDRESS BUS
DATA
48
DATA
FLAGS
ASYNCHRONOUS
MEMORY
INTERFACE
(AMI)
PWM
24
ADDRESS
3
32
AMI CONTROL
7
32
PM DATA BUS
64
DDR2 CONTROL
16
DDR2 DRAM
CONTROLLER
DATA
19
DM DATA BUS
64
IOA(19)
ADDRESS
IOD(32)
ACCELERATORS
FFT
GPIO
IRQ/FLAGS
S
PX REGISTER
PRECISION CLOCK
GENERATORS (4)
S/PDIF (RX/TX)
IOP REGISTER CONTROL
STATUS, & DATA BUFFERS
SERIAL PORTS (8)
INPUT DATA PORT/
PDAP
DMA
ARBITER
SPI PORT (2)
TWO WIRE
INTERFACE
GPIO
ASRC
DPI PINS (14)
FIR
IIR
LINK
PORTS
DPI ROUTING UNIT
4
PROCESSING
ELEMENT
(PEY)
DAI ROUTING UNIT
PROCESSING
ELEMENT
(PEX)
20
UART
GP TIMERS (2)
DAI PINS (20)
DIGITAL PERIPHERAL INTERFACE
DIGITAL APPLICATIONS INTERFACE
20
14
I/O PROCESSOR
Figure 1. Functional Block Diagram
SHARC and the SHARC logo are registered trademarks of Analog Devices, Inc.
Rev. PrB
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.3113
©2008 Analog Devices, Inc. All rights reserved.
ADSP-21469/ADSP-21469W
Preliminary Technical Data
KEY FEATURES—PROCESSOR CORE
At 450 MHz core instruction rate, the ADSP-21469 performs
at 2.7 GFLOPS/900 MMACs
5 Mbits on-chip, RAM for simultaneous access by the core
processor and DMA
DDR2 DRAM interface (16-bit) operating at maximum frequency of half the core clock frequency
Dual data address generators (DAGs) with modulo and bitreverse addressing
Zero-overhead looping with single-cycle loop setup, providing efficient program sequencing
VISA (variable instruction set) execution support
Single instruction multiple data (SIMD) architecture
provides:
Two computational processing elements
Concurrent execution
Code compatibility with other SHARC family members at
the assembly level
Parallelism in buses and computational units allows:
Single cycle executions (with or without SIMD) of a multiply operation, an ALU operation, a dual memory read
or write, and an instruction fetch
Transfers between memory and core at a sustained
7.2 Gbytes/second bandwidth
FFT accelerator implements radix-2 complex/real input, complex output FFT with no core intervention
IIR accelerators perform dedicated IIR filtering with high-performance, fixed- and floating-point processing capabilities
with no core intervention
FIR accelerators perform dedicated FIR filtering with highperformance, fixed- and floating-point processing capabilities with no core intervention
In the ADSP-21469, the program sequencer can execute code
directly from external memory bank 0 (SRAM, as well as
DDR2 DRAM). This allows more options to a user in terms
of code and data storage.
New opcodes of 16 and 32 bits are supported in addition to
the existing 48 bit opcodes. Variable Instruction Set Architecture (VISA) execution from external DDR2 DRAM
memory is also supported.
INPUT/OUTPUT FEATURES
Two 8-bit wide link ports can connect to the link ports of
other SHARCs or peripherals. Link ports are bidirectional
programmable ports having eight data lines, an acknowledge line and a clock line. Link ports can operate at a
maximum frequency of 166 MHz.
DMA controller supports:
36 DMA channels for transfers between ADSP-21469 internal memory and a variety of peripherals
DMA transfers at peripheral clock speed, in parallel with
full-speed processor execution
External port provides glueless connection to 16-bit wide
synchronous DDR2 DRAM using a dedicated DDR2 DRAM
controller, and 8-bit wide asynchronous memory devices
using asynchronous memory interface (AMI)
Rev. PrB |
Page 2 of 56 |
Programmable wait state options (for AMI): 2 to 31
DDR2_CLK cycles
Delay-line DMA engine maintains circular buffers in
external memory with tap/offset based reads
16-bit data access for synchronous DDR2 DRAM
8-bit data access for asynchronous memory
4 memory select lines allows multiple external memory
devices
Digital audio interface (DAI) includes eight serial ports, four
precision clock generators, an input data port, an S/PDIF
transceiver, and a signal routing unit
Digital peripheral interface (DPI) includes, two timers, one
UART, and two SPI ports, and a two-wire interface port
Outputs of PCG’s A and B can be routed through DAI pins
Outputs of PCG's C and D can be driven on to DAI as well as
DPI pins
Eight dual data line serial ports— each has a clock, frame
sync, and two data lines that can be configured as either a
receiver or transmitter pair
TDM support for telecommunications interfaces including
128 TDM channel support for newer telephony interfaces
such as H.100/H.110
Up to 16 TDM stream support, each with 128 channels per
frame
Companding selection on a per channel basis in TDM mode
Input data port (IDP), configurable as eight channels of serial
data or seven channels of serial data and up to a 20-bit
wide parallel data channel
Signal routing unit provides configurable and flexible connections between the various peripherals and the DAI/DPI
components
4 independent asynchronous sample rate converters (ASRC).
Each converter has separate serial input and output ports,
a de-emphasis filter providing up to –128 dB SNR performance, stereo sample rate converter and supports leftjustified, I2S, TDM, and right-justified modes and 24-, 20-,
18-, and 16-audio data word lengths.
2 muxed flag/IRQ lines
1 muxed flag/IRQ /AMI_MS pin
1 muxed flag/Timer expired line /AMI_MS pin
S/PDIF-compatible digital audio receiver/transmitter supports EIAJ CP-340 (CP-1201), IEC-958, AES/EBU standards
Left-justified, I2S or right-justified serial data input with
16-, 18-, 20- or 24-bit word widths (transmitter)
Pulse-width modulation provides:
16 PWM outputs configured as four groups of four outputs
supports center-aligned or edge-aligned PWM waveforms
PLL has a wide variety of software and hardware multiplier/divider ratios
Thermal diode to monitor die temperature
Available in 19 mm by 19 mm PBGA package (see Ordering
Guide on Page 56)
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
TABLE OF CONTENTS
Summary ............................................................... 1
Key Features—Processor Core ................................. 2
Input/Output Features ........................................... 2
Table Of Contents .................................................... 3
Revision History ...................................................... 3
General Description ................................................. 4
Family Core Architecture ....................................... 5
Memory ............................................................. 6
External Memory .................................................. 6
Input/Output Features ........................................... 7
System Design ..................................................... 10
Development Tools .............................................. 10
Additional Information ......................................... 11
Pin Function Descriptions ........................................ 12
Data Modes ........................................................ 15
Boot Modes ........................................................ 15
Core Instruction Rate to CLKIN Ratio Modes ............. 15
Specifications ......................................................... 16
Operating Conditions ........................................... 16
Electrical Characteristics ........................................ 17
Maximum Power Dissipation ................................. 18
Absolute Maximum Ratings ................................... 18
ESD Sensitivity .................................................... 18
Timing Specifications ........................................... 19
Output Drive Currents .......................................... 50
Test Conditions ................................................... 50
Capacitive Loading ............................................... 50
Thermal Characteristics ........................................ 51
Ball configuration - ADSP-21469 ............................. 52
PBGA Pinout ......................................................... 53
Outline Dimensions ................................................ 55
Automotive Products ............................................... 56
Ordering Guide ...................................................... 56
REVISION HISTORY
11/08—Revision PrB
Rev. PrB |
Page 3 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
GENERAL DESCRIPTION
The ADSP-21469 SHARC® processor is a member of the SIMD
SHARC family of DSPs that feature Analog Devices' Super Harvard Architecture. The ADSP-21469 is source code compatible
with the ADSP-2126x, ADSP-2136x, ADSP-2137x, and ADSP2116x DSPs as well as with first generation ADSP-2106x
SHARC processors in SISD (single-instruction, single-data)
mode. The ADSP-21469 is a 32-bit/40-bit floating point processors optimized for high performance audio applications with its
large on-chip SRAM, multiple internal buses to eliminate I/O
bottlenecks, and an innovative digital applications interface
(DAI).
Table 2 shows performance benchmarks for the ADSP-21469.
Table 2. Processor Benchmarks
Benchmark Algorithm
1024 Point Complex FFT (Radix 4, With Reversal)
FIR Filter (per Tap)1
IIR Filter (per Biquad)1
Matrix Multiply (Pipelined)
[3 × 3] × [3 × 1]
[4 × 4] × [4 × 1]
Divide (y/×)
Inverse Square Root
Table 1. SHARC Features
Speed
(at 450 MHz)
20.44 μs
1.11 ns
4.43 ns
10.0 ns
17.78 ns
6.67 ns
10.0 ns
Feature
Description
Frequency
450 MHz
Core
5-stage pipeline
Internal RAM
5 Mbits
DDR2 Memory Interface
1/2 CCLK Max
DDR2 Memory Bus Width
16-bits
Direct DMA from SPORTs to external
memory
Yes
• Two processing elements, each of which comprises an
ALU, multiplier, shifter, and data register file
FFT accelerator
Yes
• Data address generators (DAG1, DAG2)
FIR accelerator
Yes
• Program sequencer with instruction cache
IIR accelerator
Yes
IDP
Yes
• PM and DM buses capable of supporting four 32-bit data
transfers between memory and the core at every core processor cycle
Serial Ports
8
ASRC (channels)
8
• Two programmable interval timers with external event
counter capabilities
UART
1
• On-chip SRAM
DAI and DPI
20/14 pins
1
Assumes two files in multichannel SIMD mode
The ADSP-21469 continues SHARC’s industry-leading standards of integration for DSPs, combining a high performance
32-bit DSP core with integrated, on-chip system features.
The block diagram of the ADSP-21469 on Page 1 illustrates the
following architectural features:
• JTAG test access port
The block diagram of the ADSP-21469 on Page 1 also illustrates
the following architectural features:
Link Ports
2
S/PDIF transceiver
1
AMI interface with 8-bit support
Yes
SPI
2
TWI
1
Package
324-ball,
19 mm x 19 mm PBGA
• DMA controller
As shown in the functional block diagram on Page 1, the
ADSP-21469 uses two computational units to deliver a significant performance increase over the previous SHARC processors
on a range of DSP algorithms. Fabricated in a state-of-the-art,
high speed, CMOS process, the ADSP-21469 processor achieves
an instruction cycle time of 2.22 ns at 450 MHz. With its SIMD
computational hardware, the ADSP-21469 can perform
2.7 GFLOPS.
Rev. PrB |
Page 4 of 56 |
• Digital applications interface that includes four precision
clock generators (PCG), an S/PDIF-compatible digital
audio receiver/transmitter with four independent asynchronous sample rate converters, an input data port (IDP)
with eight serial ports, eight serial interfaces, a 20-bit parallel input port (PDAP), and a flexible signal routing unit
(DAI SRU).
• Digital peripheral interface that includes two timers, one
UART, two serial peripheral interfaces (SPI), a 2-wire
interface (TWI), and a flexible signal routing unit
(DPI SRU).
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
FAMILY CORE ARCHITECTURE
The ADSP-21469 is code compatible at the assembly level with
the ADSP-2137x, ADSP-2136x, ADSP-2126x, ADSP-21160, and
ADSP-21161, and with the first generation ADSP-2106x
SHARC processors. The ADSP-21469 shares architectural features with the ADSP-2126x, ADSP-2136x, ADSP-2137x, and
ADSP-2116x SIMD SHARC processors, as detailed in the following sections.
SIMD Computational Engine
The ADSP-21469 contains two computational processing elements that operate as a single-instruction, multiple-data
(SIMD) engine. The processing elements are referred to as PEX
and PEY and each contains an ALU, multiplier, shifter, and register file. PEX is always active, and PEY may be enabled by
setting the PEYEN mode bit in the MODE1 register. When this
mode is enabled, the same instruction is executed in both processing elements, but each processing element operates on
different data. This architecture is efficient at executing math
intensive DSP algorithms.
Entering SIMD mode also has an effect on the way data is transferred between memory and the processing elements. When in
SIMD mode, twice the data bandwidth is required to sustain
computational operation in the processing elements. Because of
this requirement, entering SIMD mode also doubles the bandwidth between memory and the processing elements. When
using the DAGs to transfer data in SIMD mode, two data values
are transferred with each access of memory or the register file.
Independent, Parallel Computation Units
Within each processing element is a set of computational units.
The computational units consist of an arithmetic/logic unit
(ALU), multiplier, and shifter. These units perform all operations in a single cycle. The three units within each processing
element are arranged in parallel, maximizing computational
throughput. Single multifunction instructions execute parallel
ALU and multiplier operations. In SIMD mode, the parallel
ALU and multiplier operations occur in both processing elements. These computation units support IEEE 32-bit singleprecision floating-point, 40-bit extended precision floatingpoint, and 32-bit fixed-point data formats.
Data Register File
A general-purpose data register file is contained in each processing element. The register files transfer data between the
computation units and the data buses, and store intermediate
results. These 10-port, 32-register (16 primary, 16 secondary)
register files, combined with the ADSP-21469 enhanced Harvard architecture, allow unconstrained data flow between
computation units and internal memory. The registers in PEX
are referred to as R0-R15 and in PEY as S0-S15.
Single-Cycle Fetch of Instruction and Four Operands
gram and data memory buses and on-chip instruction cache,
the processor can simultaneously fetch four operands (two over
each data bus) and one instruction (from the cache), all in a single cycle.
Instruction Cache
The ADSP-21469 includes an on-chip instruction cache that
enables three-bus operation for fetching an instruction and four
data values. The cache is selective—only the instructions whose
fetches conflict with PM bus data accesses are cached. This
cache allows full speed execution of core, looped operations
such as digital filter multiply-accumulates, and FFT butterfly
processing.
Data Address Generators With Zero-Overhead Hardware
Circular Buffer Support
The ADSP-21469’s two data address generators (DAGs) are
used for indirect addressing and implementing circular data
buffers in hardware. Circular buffers allow efficient programming of delay lines and other data structures required in digital
signal processing, and are commonly used in digital filters and
Fourier transforms. The two DAGs of the ADSP-21469 contain
sufficient registers to allow the creation of up to 32 circular buffers (16 primary register sets, 16 secondary). The DAGs
automatically handle address pointer wraparound, reduce overhead, increase performance, and simplify implementation.
Circular buffers can start and end at any memory location.
Flexible Instruction Set
The 48-bit instruction word accommodates a variety of parallel
operations, for concise programming. For example, the
ADSP-21469 can conditionally execute a multiply, an add, and a
subtract in both processing elements while branching and fetching up to four 32-bit values from memory—all in a single
instruction.
Variable Instruction Set Architecture
In addition to supporting the standard 48-bit instructions from
previously existing SHARC family of processors, the ADSP21469 will support new instructions of 16 and 32 bits in addition
to the existing 48 bit instructions. This feature, called Variable
Instruction Set Architecture (VISA), is based on dropping
redundant/unused bits within the 48-bit instruction to create
more efficient and compact code. The program sequencer will
now support fetching these 16-bit and 32-bit instructions as well
in addition to the standard 48-bit instructions, both from internal as well as external memory. Source modules will need to be
built using the VISA option, in order to allow code generation
tools to create these more efficient opcodes.
FFT Accelerator
FFT accelerator implements radix-2 complex/real input, complex output FFT with no core intervention.
The ADSP-21469 features an enhanced Harvard architecture in
which the data memory (DM) bus transfers data and the program memory (PM) bus transfers both instructions and data
(see Figure 1 on page 1). With the ADSP-21469’s separate pro-
Rev. PrB |
Page 5 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
FIR Accelerators
MEMORY
The FIR (finite impulse response) accelerator consists of a 1024
word coefficient memory, a 1024 word deep delay line for the
data, and four MAC units. A controller manages the accelerator.
The FIR accelerator runs at the peripheral clock frequency.
The ADSP-21469 adds the following architectural features to
the SIMD SHARC family core.
On-Chip Memory
The ADSP-21469 contains 5 Mbits of internal RAM. Each block
can be configured for different combinations of code and data
storage (see Table 3). Each memory block supports single-cycle,
independent accesses by the core processor and I/O processor.
The ADSP-21469 memory architecture, in combination with its
separate on-chip buses, allow two data transfers from the core
and one from the I/O processor, in a single cycle.
IIR Accelerators
The IIR (infinite impulse response) accelerator consists of a
1440 word coefficient memory for storage of biquad coefficients, a data memory for storing the intermediate data and one
MAC unit. A controller manages the accelerator. The IIR accelerator runs at the peripheral clock frequency.
Table 3. ADSP-21469 Internal Memory Space
IOP Registers 0x0000 0000–0x0003 FFFF
Long Word (64 bits)
Extended Precision Normal or
Instruction Word (48 bits)
Normal Word (32 bits)
Short Word (16 bits)
BLOCK 0 RAM
0x0004 9000–0x0004 EFFF
BLOCK 0 RAM
0x0008 C000-0x0009 3FFF
BLOCK 0 RAM
0x0009 2000-0x0009 DFFF
BLOCK 0 RAM
0x0012 4000–0x0013 BFFF
Reserved
0x0004 F000–0x0005 8FFF
Reserved
0x0009 E000–0x000B 1FFF
Reserved
0x0009 E000–0x000B 1FFF
Reserved
0x0013 C000–0x0016 3FFF
BLOCK 1 RAM
0x0005 9000–0x0005 EFFF
BLOCK 1 RAM
0x000A C000-0x000B 3FFF
BLOCK 1 RAM
0x000B 2000-0x000B DFFF
BLOCK 1 RAM
0x0016 4000-0x0017 BFFF
Reserved
0x0005 F000–0x0005 FFFF
Reserved
0x000B E000–0x000B FFFF
Reserved
0x000B E000–0x000B FFFF
Reserved
0x0017 C000–0x0017 FFFF
BLOCK 2 RAM
0x0006 0000–0x0006 3FFF
BLOCK 2 RAM
0x000C 0000–0x000C 5554
BLOCK 2 RAM
0x000C 0000-0x000C 7FFF
BLOCK 2 RAM
0x0018 0000–0x0018 FFFF
Reserved
0x0006 4000–0x0006 FFFF
Reserved
0x000C 8000–0x000D FFFF
Reserved
0x000C 8000–0x000D FFFF
Reserved
0x0019 0000–0x001B FFFF
BLOCK 3 RAM
0x0007 0000–0x0007 3FFF
BLOCK 3 RAM
0x000E 0000–0x000E 5554
BLOCK 3 RAM
0x000E 0000–0x000E 7FFF
BLOCK 3 RAM
0x001C 0000–0x001C FFFF
Reserved
0x0007 4000–0x0007 FFFF
Reserved
0x000E 8000–0x000F FFFF
Reserved
0x000E 8000–0x000F FFFF
Reserved
0x001D 0000–0x001F FFFF
The ADSP-21469’s SRAM can be configured as a maximum of
160k words of 32-bit data, 320k words of 16-bit data, 106.7k
words of 48-bit instructions (or 40-bit data), or combinations of
different word sizes up to 5 megabit. All of the memory can be
accessed as 16-bit, 32-bit, 48-bit, or 64-bit words. A 16-bit floating-point storage format is supported that effectively doubles
the amount of data that may be stored on-chip. Conversion
between the 32-bit floating-point and 16-bit floating-point formats is performed in a single instruction. While each memory
block can store combinations of code and data, accesses are
most efficient when one block stores data using the DM bus for
transfers, and the other block stores instructions and data using
the PM bus for transfers.
Using the DM bus and PM buses, with one bus dedicated to a
memory block, assures single-cycle execution with two data
transfers. In this case, the instruction must be available in the
cache.
Rev. PrB |
Page 6 of 56 |
The memory map in Table 3 displays the internal memory
address space of the ADSP-21469.
The 48-bit space section describes what this address range looks
like to an instruction that retrieves 48-bit memory.
The 32-bit section describes what this address range looks like
to an instruction that retrieves 32-bit memory.
EXTERNAL MEMORY
The external port on the ADSP-21469 SHARC provides a high
performance, glueless interface to a wide variety of industrystandard memory devices. The external port may be used to
interface to synchronous and/or asynchronous memory devices
through the use of its separate internal memory controllers: the
16-bit DDR2 DRAM controller for connection of industry-standard synchronous DRAM devices, while the second is an 8-bit
asynchronous memory controller intended to interface to a
variety of memory devices. Four memory select pins enable up
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
to four separate devices to coexist, supporting any desired combination of synchronous and asynchronous device types. Non
DDR2 DRAM external memory address space is shown in
Table 4.
External Memory Execution
In the ADSP-21469, the program sequencer can execute code
directly from external memory bank 0 (SRAM, as well as DDR2
DRAM). This allows more options to a user in terms of code
and data storage. With external execution, programs run at
slower speeds since 48-bit instructions are fetched in parts from
a 16-bit external bus coupled with the inherent latency of fetching instructions from DDR2 DRAM. VISA mode and SIMD
mode accesses are supported for DDR2 space. However, external memory execution from DDR2 space is different for VISA
and non-VISA mode.
DDR2 Support
The ADSP-21469 supports a 16-bit DDR interface operating at a
maximum frequency of half the core clock. Execution from
external memory is supported. External memory up to 2 Gbits
can be supported. Delay line DMA functionality supported.
DDR2 DRAM Controller
The DDR2 DRAM controller provides an 16-bit interface to up
to four separate banks of industry-standard DDR2 DRAM
devices. Fully compliant with the DDR2 DRAM standard, each
bank can has its own memory select line (DDR2_CS3DDR2_CS0), and can be configured to contain between 32M
bytes and 256M bytes of memory. DDR2 DRAM external memory address space is shown in Table 5
A set of programmable timing parameters is available to configure the DDR2 DRAM banks to support memory devices.
Table 4. External Memory for Non DDR2 DRAM Addresses
Note that the external memory bank addresses shown are for
normal-word (32-bit) accesses. If 48-bit instructions as well as
32-bit data are both placed in the same external memory bank,
care must be taken while mapping them to avoid overlap. In
case of 32-bit wide external memory, two 48-bit instructions
will be stored in three 32-bit wide memory locations. For example, if 2k instructions are placed in 32-bit wide external memory
starting at the bank 0 normal-word base address 0x0030 0000
(corresponding to instruction address 0x0020 0000) and ending
at address 0x0030 0BFF (corresponding to instruction address
0x0020 07FF), then data buffers can be placed starting at an
address that is offset by 3k 32-bit words (for example, starting at
0x0030 0C00).
Asynchronous Memory Controller
The asynchronous memory controller provides a configurable
interface for up to four separate banks of memory or I/O
devices. Each bank can be independently programmed with different timing parameters, enabling connection to a wide variety
of memory devices including SRAM, flash, and EPROM, as well
as I/O devices that interface with standard memory control
lines. Bank 0 occupies a 14M word window and banks 1, 2, and
3 occupy a 16M word window in the processor’s address space
but, if not fully populated, these windows are not made contiguous by the memory controller logic.
The asynchronous memory controller is capable of a maximum
throughput of TBD Mbps using a TBD MHz external bus speed.
Other features include 8 to 32-bit packing and unpacking, booting from bank select 1, and support for delay line DMA.
Shared External Memory
The ADSP-21469 processor supports connecting to common
shared external DDR2 memory with other ADSP-21469 processors to create shared external bus processor systems. This
support includes:
• Distributed, on-chip arbitration for the shared external bus
Bank
Size in
Words
Address Range
Bank 0
14M
0x0020 0000 – 0x00FF FFFF
Bank 1
16M
0x0400 0000 – 0x04FF FFFF
Bank 2
16M
0x0800 0000 – 0x08FF FFFF
Bank 3
16M
0x0C00 0000 – 0x0CFF FFFF
• Fixed and rotating priority bus arbitration
• Bus time-out logic
• Bus lock
Multiple processors can share the external bus with no additional arbitration logic. Arbitration logic is included on-chip to
allow the connection of up to TBD processors.
Bus arbitration is accomplished through the BR6-1 signals and
the priority scheme for bus arbitration is determined by the setting of the RPBA pin. Table 6 on Page 12 provides descriptions
of the pins used in multiprocessor systems.
Table 5. External Memory for DDR2 DRAM Addresses
Bank
Size in
Words
Address Range
INPUT/OUTPUT FEATURES
Bank 0
62M
0x0020 0000 – 0x03FF FFFF
Bank 1
64M
0x0400 0000 – 0x07FF FFFF
Bank 2
64M
0x0800 0000 – 0x0BFF FFFF
The ADSP-21469 I/O processor provides 36 channels of DMA,
as well as an extensive set of peripherals. These include a 20 lead
digital applications interface, which controls:
Bank 3
64M
0x0C00 0000 – 0x0FFF FFFF
Rev. PrB |
Page 7 of 56 |
• Eight serial ports
• S/PDIF receiver/transmitter
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
associated peripherals for a much wider variety of applications
by using a larger set of algorithms than is possible with nonconfigurable signal paths.
• Four precision clock generators
• Input data port/parallel data acquisition port
• Four stereo asynchronous sample rate converters
The ADSP-21469 processor also contains a 14 lead digital
peripheral interface, which controls:
• Two general-purpose timers
• Two serial peripheral interfaces
• One universal asynchronous receiver/transmitter (UART)
• An I2C®-compatible 2-wire interface
The DAI also includes eight serial ports, four precision clock
generators (PCG), S/PDIF transceiver, four ASRCs, and an
input data port (IDP). The IDP provides an additional input
path to the ADSP-21469 core, configurable as either eight channels of serial data, or a single 20-bit wide synchronous parallel
data acquisition port. Each data channel has its own DMA
channel that is independent from the ADSP-21469’s serial ports.
Serial Ports
• Two PCGs (C and D) can also be routed through DPI
DMA Controller
The ADSP-21469’s on-chip DMA controller allows data transfers without processor intervention. The DMA controller
operates independently and invisibly to the processor core,
allowing DMA operations to occur while the core is simultaneously executing its program instructions. DMA transfers can
occur between the ADSP-21469’s internal memory and its serial
ports, the SPI-compatible (serial peripheral interface) ports, the
IDP (input data port), the parallel data acquisition port (PDAP)
or the UART.
Thirty-six channels of DMA are available on the ADSP-21469,
16 via the serial ports, eight via the input data port, two for the
UART, two for the SPI interface, two for the external port, two
for memory-to-memory transfers, two for the link port, two for
the FFT/IIR/FIR accelerator.
Programs can be downloaded to the ADSP-21469 using DMA
transfers. Other DMA features include interrupt generation
upon completion of DMA transfers, and DMA chaining for
automatic linked DMA transfers.
The ADSP-21469 features eight synchronous serial ports that
provide an inexpensive interface to a wide variety of digital and
mixed-signal peripheral devices such as Analog Devices’
AD183x family of audio codecs, ADCs, and DACs. The serial
ports are made up of two data lines, a clock, and frame sync. The
data lines can be programmed to either transmit or receive and
each data line has a dedicated DMA channel.
Serial ports can support up to 16 transmit or 16 receive channels
of audio data when all eight SPORTs are enabled, or four full
duplex TDM streams of 128 channels per frame.
The serial ports operate at a maximum data rate of 56.25 Mbps.
Serial port data can be automatically transferred to and from
on-chip memory/external memory via dedicated DMA channels. Each of the serial ports can work in conjunction with
another serial port to provide TDM support. One SPORT provides two transmit signals while the other SPORT provides the
two receive signals. The frame sync and clock are shared.
Serial ports operate in five modes:
• Standard DSP serial mode
• Multichannel (TDM) mode
Delay Line DMA
• I2S mode
The ADSP-21469 processor provides delay line DMA functionality. This allows processor reads and writes to external delay
line buffers (and hence to external memory) with limited core
interaction.
• Packed I2S mode
Scatter/Gather DMA
The ADSP-21469 processor provides scatter/gather DMA
functionality.
This allows processor DMA reads/writes to/from non-contingeous memory blocks.
Digital Applications Interface (DAI)
The digital applications interface (DAI) provides the ability to
connect various peripherals to any of the DSP DAI pins
(DAI_P20–1).
Programs make these connections using the signal routing unit
(SRU), shown in Figure 1.
The SRU is a matrix routing unit (or group of multiplexers) that
enables the peripherals provided by the DAI to be interconnected under software control. This allows easy use of the DAI
Rev. PrB |
Page 8 of 56 |
• Left-justified sample pair mode
Left-justified sample pair mode is a mode where in each frame
sync cycle two samples of data are transmitted/received—one
sample on the high segment of the frame sync, the other on the
low segment of the frame sync. Programs have control over various attributes of this mode.
Each of the serial ports supports the left-justified sample pair
and I2S protocols (I2S is an industry-standard interface commonly used by audio codecs, ADCs, and DACs such as the
Analog Devices AD183x family), with two data pins, allowing
four left-justified sample pair or I2S channels (using two stereo
devices) per serial port, with a maximum of up to 32 I2S channels. The serial ports permit little-endian or big-endian
transmission formats and word lengths selectable from 3 bits to
32 bits. For the left-justified sample pair and I2S modes, dataword lengths are selectable between 8 bits and 32 bits. Serial
ports offer selectable synchronization and transmit modes as
well as optional μ-law or A-law companding selection on a per
channel basis. Serial port clocks and frame syncs can be internally or externally generated.
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
The serial ports also contain frame sync error detection logic
where the serial ports detect frame syncs that arrive early (for
example frame syncs that arrive while the transmission/reception of the previous word is occurring). All the serial ports also
share one dedicated error interrupt.
S/PDIF-Compatible Digital Audio Receiver/Transmitter
and Synchronous/Asynchronous Sample Rate Converter
The S/PDIF receiver/transmitter has no separate DMA channels. It receives audio data in serial format and converts it into a
biphase encoded signal. The serial data input to the
receiver/transmitter can be formatted as left justified, I2S or
right justified with word widths of 16, 18, 20, or 24 bits.
The serial data, clock, and frame sync inputs to the S/PDIF
receiver/transmitter are routed through the signal routing unit
(SRU). They can come from a variety of sources such as the
SPORTs, external pins, the precision clock generators (PCGs),
and are controlled by the SRU control registers.
The sample rate converter (ASRC) contains four ASRC blocks
and is the same core as that used in the AD1896 192 kHz stereo
asynchronous sample rate converter and provides up to 128 dB
SNR. The ASRC block is used to perform synchronous or asynchronous sample rate conversion across independent stereo
channels, without using internal processor resources. The four
SRC blocks can also be configured to operate together to convert multichannel audio data without phase mismatches.
Finally, the ASRC can be used to clean up audio data from jittery clock sources such as the S/PDIF receiver.
Digital Peripheral Interface (DPI)
The digital peripheral interface provides connections to two
serial peripheral interface ports (SPI), one universal asynchronous receiver-transmitter (UART), 12 flags, a 2-wire interface
(TWI), and two general-purpose timers.
transfers of serial data. The UART also has multiprocessor communication capability using 9-bit address detection. This allows
it to be used in multidrop networks through the RS-485 data
interface standard. The UART port also includes support for 5
to 8 data bits, 1 or 2 stop bits, and none, even, or odd parity. The
UART port supports two modes of operation:
• PIO (programmed I/O) – The processor sends or receives
data by writing or reading I/O-mapped UART registers.
The data is double-buffered on both transmit and receive.
• DMA (direct memory access) – The DMA controller transfers both transmit and receive data. This reduces the
number and frequency of interrupts required to transfer
data to and from memory. The UART has two dedicated
DMA channels, one for transmit and one for receive. These
DMA channels have lower default priority than most DMA
channels because of their relatively low service rates.
The UART port's baud rate, serial data format, error code generation and status, and interrupts are programmable:
• Supporting bit rates ranging from (fPCLK/ 1,048,576) to
(fPCLK/16) bits per second.
• Supporting data formats from 7 to 12 bits per frame.
• Both transmit and receive operations can be configured to
generate maskable interrupts to the processor.
In conjunction with the general-purpose timer functions, autobaud detection is supported.
Timers
The ADSP-21469 has a total of three timers: a core timer that
can generate periodic software interrupts and two general purpose timers that can generate periodic interrupts and be
independently set to operate in one of three modes:
• Pulse waveform generation mode
Serial Peripheral (Compatible) Interface
• Pulse width count/capture mode
The ADSP-21469 SHARC processor contains two serial peripheral interface ports (SPIs). The SPI is an industry-standard
synchronous serial link, enabling the ADSP-21469 SPI-compatible port to communicate with other SPI compatible devices.
The SPI consists of two data pins, one device select pin, and one
clock pin. It is a full-duplex synchronous serial interface, supporting both master and slave modes. The SPI port can operate
in a multimaster environment by interfacing with up to four
other SPI-compatible devices, either acting as a master or slave
device. The ADSP-21469 SPI-compatible peripheral implementation also features programmable baud rate and clock phase
and polarities. The ADSP-21469 SPI-compatible port uses open
drain drivers to support a multimaster configuration and to
avoid data contention.
• External event watchdog mode
UART Port
The ADSP-21469 processor provides a full-duplex Universal
Asynchronous Receiver/Transmitter (UART) port, which is
fully compatible with PC-standard UARTs. The UART port
provides a simplified UART interface to other peripherals or
hosts, supporting full-duplex, DMA-supported, asynchronous
Rev. PrB |
Page 9 of 56 |
The core timer can be configured to use FLAG3 as a timer
expired signal, and each general-purpose timer has one bidirectional pin and four registers that implement its mode of
operation: a 6-bit configuration register, a 32-bit count register,
a 32-bit period register, and a 32-bit pulse width register. A single control and status register enables or disables both generalpurpose timers independently.
2-Wire Interface Port (TWI)
The TWI is a bidirectional 2-wire, serial bus used to move 8-bit
data while maintaining compliance with the I2C bus protocol.
The TWI master incorporates the following features:
• 7-bit addressing
• Simultaneous master and slave operation on multiple
device systems with support for multi master data
arbitration
• Digital filtering and timed event processing
• 100 kbps and 400 kbps data rates
• Low interrupt rate
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Pulse-Width Modulation
The PWM module is a flexible, programmable, PWM waveform
generator that can be programmed to generate the required
switching patterns for various applications related to motor and
engine control or audio power control. The PWM generator can
generate either center-aligned or edge-aligned PWM waveforms. In addition, it can generate complementary signals on
two outputs in paired mode or independent signals in nonpaired mode (applicable to a single group of four PWM
waveforms).
The entire PWM module has four groups of four PWM outputs
each. Therefore, this module generates 16 PWM outputs in
total. Each PWM group produces two pairs of PWM signals on
the four PWM outputs.
The PWM generator is capable of operating in two distinct
modes while generating center-aligned PWM waveforms: single
update mode or double update mode. In single update mode the
duty cycle values are programmable only once per PWM period.
This results in PWM patterns that are symmetrical about the
mid-point of the PWM period. In double update mode, a second updating of the PWM registers is implemented at the midpoint of the PWM period. In this mode, it is possible to produce
asymmetrical PWM patterns that produce lower harmonic distortion in three-phase PWM inverters.
Link Ports
Two 8-bit wide link ports can connect to the link ports of other
DSPs or peripherals. Link ports are bidirectional ports having
eight data lines, an acknowledge line and a clock line. Link ports
can operate at a maximum frequency of 166 MHz.
SYSTEM DESIGN
The following sections provide an introduction to system design
options and power supply issues.
Program Booting
Note that the analog supply pin (VDD_A) powers the processor’s
internal clock generator PLL. To produce a stable clock, it is recommended that PCB designs use an external filter circuit for the
VDD_A pin. Place the filter components as close as possible to
the VDD_A/VSS_A pins. For an example circuit, see Figure 2. (A
recommended ferrite chip is the muRata BLM18AG102SN1D).
100nF
10nF
1nF
ADSP-21469
VDD_A
VDDINT
HI Z FERRITE
BEAD CHIP
VSS_A
LOCATE ALL COMPONENTS
CLOSE TO VDD_A AND VSS_A PINS
Figure 2. Analog Power (VDD_A) Filter Circuit
To reduce noise coupling, the PCB should use a parallel pair of
power and ground planes for VDD_INT and VSS. Use wide traces
to connect the bypass capacitors to the analog power (VDD_A)
and ground (VSS_A) pins. Note that the VDD_A and VSS_A pins
specified in Figure 2 are inputs to the processor and not the analog ground plane on the board—the VSS_A pin should connect
directly to digital ground (VSS) at the chip
Target Board JTAG Emulator Connector
Analog Devices DSP Tools product line of JTAG emulators uses
the IEEE 1149.1 JTAG test access port of the ADSP-21469 processor to monitor and control the target board processor during
emulation. Analog Devices DSP Tools product line of JTAG
emulators provides emulation at full processor speed, allowing
inspection and modification of memory, registers, and processor stacks. The processor's JTAG interface ensures that the
emulator will not affect target system loading or timing.
The internal memory of the ADSP-21469 boots at system
power-up from an 8-bit EPROM via the external port, link port,
an SPI master, or an SPI slave. Booting is determined by the
boot configuration (BOOTCFG2–0) pins (see Table 8 on
Page 15).
For complete information on Analog Devices’ SHARC DSP
Tools product line of JTAG emulator operation, see the appropriate “Emulator Hardware User's Guide”.
The “Running Reset” feature allows a user to perform a reset of
the processor core and peripherals, but without resetting the
PLL and DDR2 DRAM controller, or performing a Boot. The
functionality of the CLKOUT/RESETOUT/RUNRSTIN pin has
now been extended to also act as the input for initiating a Running Reset. For more information, see the ADSP-2146x SHARC
Processor Hardware Reference.
The ADSP-21469 processor is supported with a complete set of
CROSSCORE® software and hardware development tools,
including Analog Devices emulators and VisualDSP++® development environment. The same emulator hardware that
supports other SHARC processors also fully emulates the
ADSP-21469 processor.
Power Supplies
For evaluation of the processors, use the EZ-KIT Lite® board
being developed by Analog Devices. The board comes with onchip emulation capabilities and is equipped to enable software
development. Multiple daughter cards are available.
The processors have separate power supply connections for the
internal (VDD_INT), external (VDD_EXT), and analog
(VDD_A/VSS_A) power supplies. The internal and analog supplies
must meet the VDD_INT specifications. The external supply must
meet the VDD_EXT specification. All external supply pins must
be connected to the same power supply.
Rev. PrB |
Page 10 of 56 |
DEVELOPMENT TOOLS
EZ-KIT Lite Evaluation Board
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Designing an Emulator-Compatible DSP Board (Target)
Evaluation Kit
The Analog Devices family of emulators are tools that every
DSP developer needs to test and debug hardware and software
systems. Analog Devices has supplied an IEEE 1149.1 JTAG
Test Access Port (TAP) on each JTAG DSP. Nonintrusive incircuit emulation is assured by the use of the processor’s JTAG
interface—the emulator does not affect target system loading or
timing. The emulator uses the TAP to access the internal features of the processor, allowing the developer to load code, set
breakpoints, observe variables, observe memory, and examine
registers. The processor must be halted to send data and commands, but once an operation has been completed by the
emulator, the DSP system is set running at full speed with no
impact on system timing.
Analog Devices offers a range of EZ-KIT Lite® evaluation platforms to use as a cost effective method to learn more about
developing or prototyping applications with Analog Devices
processors, platforms, and software tools. Each EZ-KIT Lite
includes an evaluation board along with an evaluation suite of
the VisualDSP++® development and debugging environment
with the C/C++ compiler, assembler, and linker. Also included
are sample application programs, power supply, and a USB
cable. All evaluation versions of the software tools are limited
for use only with the EZ-KIT Lite product.
To use these emulators, the target board must include a header
that connects the DSP’s JTAG port to the emulator.
For details on target board design issues including mechanical
layout, single processor connections, signal buffering, signal termination, and emulator pod logic, see the EE-68: Analog Devices
JTAG Emulation Technical Reference on the Analog Devices
website (www.analog.com)—use site search on “EE-68.” This
document is updated regularly to keep pace with improvements
to emulator support.
The USB controller on the EZ-KIT Lite board connects the
board to the USB port of the user’s PC, enabling the
VisualDSP++ evaluation suite to emulate the on-board processor in-circuit. This permits the customer to download, execute,
and debug programs for the EZ-KIT Lite system. It also allows
in-circuit programming of the on-board Flash device to store
user-specific boot code, enabling the board to run as a standalone unit without being connected to the PC.
With a full version of VisualDSP++ installed (sold separately),
engineers can develop software for the EZ-KIT Lite or any custom defined system. Connecting one of Analog Devices JTAG
emulators to the EZ-KIT Lite board enables high speed, nonintrusive emulation.
ADDITIONAL INFORMATION
This data sheet provides a general overview of the ADSP-21469
architecture and functionality. For detailed information on the
ADSP-21469 family core architecture and instruction set, refer
to the ADSP-2136x/ADSP-2146x SHARC Processor Programming Reference.
Rev. PrB |
Page 11 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
PIN FUNCTION DESCRIPTIONS
The following symbols appear in the Type column of Table 6:
A = asynchronous, I = input, O = output, S = synchronous,
(A/D) = active drive, (O/D) = open drain, and T = three-state,
(pd) = pull-down resistor, (pu) = pull-up resistor.
Table 6. Pin List
State
During
and After
LVTTL SSTL18 Reset
3
High-Z/
driven low
(boot)
Name
AMI_ADDR23–0
Type
O/T
AMI_DATA7–0
I/O/T
3
High-Z
DAI _P20–1
I/O with fixed weak 3
pull-up on input
path 1, 2
High-Z
DPI _P14–1
I/O with fixed weak 3
pull-up only on
input path1, 2
High-Z
AMI_ACK
I (pu)
3
O/T
3
High-Z
O/T
3
High-Z
AMI_RD
AMI_WR
DDR2_ADDR15-0
O/T
3
DDR2_BA2-0
O/T
3
O/T
3
DDR2_CAS
Description
External Address. The ADSP-21469 outputs addresses for external memory
and peripherals on these pins. The data pins can be multiplexed to support
the PDAP (I) and PWM (O). After reset, all AMI_ADDR23-0 pins are in EMIF mode
and FLAG(0-3) pins will be in FLAGS mode (default). When configured in the
IDP_PDAP_CTL register, IDP channel 0 scans the AMI_ADDR23–0 pins for
parallel input data.
External Data. The data pins can be multiplexed to support the external
memory interface data (I/O), the PDAP (I), FLAGS (I/O) and PWM (O). After reset,
all AMI_DATA pins are in EMIF mode and FLAG(0-3) pins will be in FLAGS mode
(default).
Digital Applications Interface Pins. These pins provide the physical
interface to the DAI SRU. The DAI SRU configuration registers define the combination of on-chip audiocentric peripheral inputs or outputs connected to
the pin and to the pin’s output enable. The configuration registers of these
peripherals then determine the exact behavior of the pin. Any input or output
signal present in the DAI SRU may be routed to any of these pins. The DAI SRU
provides the connection from the serial ports, the S/PDIF module, input data
ports (2), and the precision clock generators (4), to the DAI_P20–1 pins.
Digital Peripheral Interface. These pins provide the physical interface to the
DPI SRU. The DPI SRU configuration registers define the combination of onchip peripheral inputs or outputs connected to the pin and to the pin’s output
enable. The configuration registers of these peripherals then determines the
exact behavior of the pin. Any input or output signal present in the DPI SRU
may be routed to any of these pins. The DPI SRU provides the connection from
the timers (2), SPIs (2), UART (1), flags (12), and general-purpose I/O (9) to the
DPI_P14–1 pins.
Memory Acknowledge (AMI_ACK). External devices can deassert AMI_ACK
(low) to add wait states to an external memory access. AMI_ACK is used by I/O
devices, memory controllers, or other peripherals to hold off completion of
an external memory access.
AMI Port Read Enable. AMI_RD is asserted whenever the ADSP-21469 reads
a word from external memory. AMI_RD has fixed internal pull-up resistor1, 2.
External Port Write Enable. AMI_WR is asserted when the ADSP-21469
writes a word to external memory. AMI_WR has fixed internal pull-up resistor1,
2
.
DDR2 Address pins. DDR2 address pins.
High-Z/
Driven low
High-Z/
DDR2 Bank Address Input pins. Define which bank an ACTIVATE,
Driven low READ, WRITE, or PRECHARGE command is being applied. BA2–0
define which mode register including MR, EMR, EMR(2), and
EMR(3) is loaded during the LOAD MODE command.
High-Z/
DDR2 Column Address Strobe. Connect to DDR2_CAS pin, in conjunction
Driven
with other DDR2 command pins, defines the operation for the DDR2 to
high
perform.
Rev. PrB |
Page 12 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Table 6. Pin List (Continued)
Name
DDR2_CKE
Type
O/T
O/T
DDR2_CS3-0
DDR2_DATA15-0
DDR2_DM1-0
I/O/T
O/T
DDR2_DQS1-0
DDR2_DQS1-0
I/O/T (Differential)
State
During
and After
LVTTL SSTL18 Reset
3
High-Z/
Driven low
3
High-Z/
Driven
high
3
High-Z
3
High-Z/
Driven
high
3
High-Z
Description
DDR2 Clock Enable Output to DDR2. Active high signal. Connect to DDR2
CKE signal.
DDR2 Chip Select. All commands are masked when DDR2_CS3-0 is driven
high. DDR2_CS3-0 are decoded emory address lines. Each DDR2_CS3-0lines
select the corresponding bank.
DDR2 Data In/Out. Connect to corresponding DDR2_DATA pins.
DDR2 Input Data Mask. Mask for the DDR2 write data if driven high. Sampled
on both edges of DDR2_DQS at DDR2 side. DM0 corresponds to DDR2_DATA
7–0 and DM1 corresponds to DDR2_DATA 15–8.
Data Strobe. Output with Write Data. Input with Read Data. DQS0 corresponds to DDR2_DATA 7–0 and DQS1 corresponds to DDR2_DATA 15–8.
DDR2 Row Address Strobe. Connect to DDR2_RAS pin, in conjunction with
other DDR2 command pins, defines the operation for the DDR2 to perform.
O/T
3
DDR2_WE
O/T
3
DDR2_CLK0,
DDR2_CLK0,
DDR2_CLK1,
DDR2_CLK1
DDR2_ODT
O/T (Differential)
3
O/T
3
AMI_MS0–1
O/T
3
FLAG[0]/IRQ0
FLAG[1]/IRQ1
FLAG[2]/IRQ2/
AMI_MS2
FLAG[3]/TIMEX P/
AMI_MS3
LDAT07–0
LDAT17-0
LCLK0
LCLK1
LACK0
LACK1
THD_P
THD_M
TDI
I/O
I/O
I/O
3
3
3
High-Z/
DDR2 On Die Termination. ODT pin when driven high (along with other
Driven low requirements) enables the DDR2 termination resistances.
High-Z
Memory Select Lines 0–1. These lines are asserted (low) as chip selects for
the corresponding banks of external memory on the AMI interface. The MS10 lines are decoded memory address lines that change at the same time as the
other address lines. When no external memory access is occurring the MS1-0
lines are inactive; they are active however when a conditional memory access
instruction is executed, whether or not the condition is true.
The MS1 pin can be used in EPORT/FLASH boot mode. For more information,
see the ADSP-2146x SHARC Processor Hardware Reference.
High-Z
FLAG0/Interrupt Request0.
High-Z
FLAG1/Interrupt Request1.
High-Z
FLAG2/Interrupt Request2/Async Memory Select2.
I/O
3
High-Z
FLAG3/Timer Expired/Async Memory Select3.
I/0
3
High-Z
Link Port Data (Link Ports 0-1).
I/O
3
High-Z
Link Port Clock (Link Ports 0–1).
I/O
3
High-Z
Link Port Acknowledge (Link Port 0-1).
I
O
I (pu)
3
TDO
TMS
O /T
I (pu)
3
3
DDR2_RAS
High-Z/
Driven
high
High-Z/
DDR2 Write Enable. Connect to DDR2_WE pin, in conjunction with other
Driven
DDR2 command pins, defines the operation for the DDR2 to perform
high
High-Z/
DDR2 Clock. Free running, minimum frequency not guaranteed during reset.
driven low
High-Z
Rev. PrB |
Thermal Diode Anode
Thermal Diode Cathode
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI
has a fixed internal pull-up resistor1, 2.
Test Data Output (JTAG). Serial scan output of the boundary scan path.
Test Mode Select (JTAG). Used to control the test state machine. TMS has a
fixed internal pull-up resistor1, 2.
Page 13 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Table 6. Pin List (Continued)
Name
TCK
Type
I (pu)
TRST
I (pu)
EMU
O/T (pu)
CLK_CFG1–0
I
BOOT_CFG2–0
I
RESET
I (pu)
XTAL
O
CLKIN
I
CLKOUT/
RESETOUT/
RUNRSTIN
I/O (pu)
BR6-1
I/O
RPBA
ID2-0
I
I
1
2
State
During
and After
LVTTL SSTL18 Reset
Description
3
Test Clock (JTAG). Provides a clock for JTAG boundary scan. TCK must be
asserted (pulsed low) after power-up or held low for proper operation of the
ADSP-21469.
3
Test Reset (JTAG). Resets the test state machine. TRST must be asserted
(pulsed low) after power-up or held low for proper operation of the ADSP21469. TRST has a fixed internal pull-up resistor1, 2.
3
High-Z
Emulation Status. Must be connected to the ADSP-21469 Analog Devices
DSP Tools product line of JTAG emulators target board connector only. EMU
has a fixed internal pull-up resistor1, 2.
3
Core to CLKIN Ratio Control. These pins set the start up clock frequency. See
Table 9 for a description of the clock configuration modes.
Note that the operating frequency can be changed by programming the PLL
multiplier and divider in the PMCTL register at any time after the core comes
out of reset.
3
Boot Configuration Select. These pins select the boot mode for the processor. The BOOTCFG pins must be valid before reset is asserted. See Table 8 for
a description of the boot modes.
3
Processor Reset. Resets the ADSP-21469 to a known state. Upon deassertion,
there is a 4096 CLKIN cycle latency for the PLL to lock. After this time, the core
begins program execution from the hardware reset vector address. The RESET
input must be asserted (low) at power-up.
3
Crystal Oscillator Terminal. Used in conjunction with CLKIN to drive an
external crystal.
3
Local Clock In. Used in conjunction with XTAL. CLKIN is the ADSP-21469 clock
input. It configures the ADSP-21469 to use either its internal clock generator
or an external clock source. Connecting the necessary components to CLKIN
and XTAL enables the internal clock generator. Connecting the external clock
to CLKIN while leaving XTAL unconnected configures the ADSP-21469 to use
the external clock source such as an external clock oscillator. CLKIN may not
be halted, changed, or operated below the specified frequency.
3
Clock Out/Reset Out/Running Reset In. The functionality can be switched
between the PLL output clock and reset out by setting Bit 12 of the PMCTL
register. The default is reset out. This pin also has a third function as RUNRSTIN.
The functionality of which is enabled by setting bit 0 of the RUNRSTCTL
register. For more information, see the ADSP-2146x SHARC Processor Hardware
Reference.
3
High-Z/
Bus request. Bus request pins for external DDR2 bus arbitration.
Driven low
3
Rotating priority bus arbitration.
3
Chip ID
Pull-up/pull-down resistor can not be enabled/disabled and the value of the pull-up/pull-down resistor cannot be programmed.
Range of fixed pull-up resistor can be between 26k-63kΩ. Range of fixed pull-down resistor can be between 31k-85kΩ.
Rev. PrB |
Page 14 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
DATA MODES
The address and data pins of the external memory interface are
muxed (using bits in the SYSCTL register) to support the external memory interface data (input/output), the PDAP (input
only), and the FLAGS (input/output). Table 7 provides the pin
settings.
Table 7. Function of Data Pins
DATA PIN MODE
000
001
010
011
100
101
110
111
AMI_ADDR [23:8]
AMI_ADDR [23:0]
AMI_ADDR [7:0]
Reserved
Reserved
FLAGS/PWM [15–0]
FLAGS [15–0]
Reserved
PDAP (DATA + CTRL)
FLAGS [7–0]
Reserved
Three-state all pins
BOOT MODES
Table 8. Boot Mode Selection
BOOTCFG2–0
000
001
010
011
100
101
110
111
Booting Mode
SPI Slave Boot
SPI Master Boot
AMI user boot (for 8-bit Flash boot)
Reserved
Link Port 0 Boot
Reserved
Reserved
Reserved
CORE INSTRUCTION RATE TO CLKIN RATIO MODES
For details on processor timing, see Timing Specifications and
Figure 3 on Page 19.
Table 9. Core Instruction Rate/ CLKIN Ratio Selection
CLKCFG1–0
00
01
11
10
AMI_DATA [7:0]
AMI_DATA [7:0]
Core to CLKIN Ratio
6:1
32:1
Reserved
16:1
Rev. PrB |
Page 15 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
SPECIFICATIONS
OPERATING CONDITIONS
Parameter1
Description
Min
Max
Unit
VDD_INT
VDD_EXT
VDD_DDR23
VREF
VIH4
VIL4
VIH_CLKIN5
VIL_CLKIN5
VIL_DDR2
VIH_DDR2
TJUNCTION
Internal (Core) Supply Voltage
External (I/O) Supply Voltage
DDR2 Controller Supply Voltage
DDR2 Reference Voltage
High Level Input Voltage @ VDD_EXT = max
Low Level Input Voltage @ VDD_EXT = min
High Level Input Voltage @ VDD_EXT = max
Low Level Input Voltage @ VDD_EXT = min
Low Level Input Voltage
High Level Input Voltage
Junction Temperature 208-Lead PBGA @ TAMBIENT 08C to +708C
TBD2
3.14
1.71
0.84
2.0
-0.3
TBD
TBD
-0.3
VREF + 0.13
0
TBD2
3.46
1.89
0.96
3.6
0.8
TBD
TBD
VREF - 0.12
VDD_DDR2 + 0.3
125
V
V
V
V
V
V
V
V
V
V
C
1
Specifications subject to change without notice.
The expected value is 1.1V and initial customer designs should design with a programmable regulator that can be adjusted from 0.95V to 1.15V +/-50mV
3
Applies to DDR2 signals.
4
Applies to input and bidirectional pins: AMI_ADDR23–0, AMI_DATA7–0, FLAG3–0, DAI_Px, DPI_Px, SPIDS, BOOTCFGx, CLKCFGx, CLKOUT (RUNRSTIN), RESET,
TCK, TMS, TDI, TRST.
5
Applies to input pin CLKIN.
2
Rev. PrB |
Page 16 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469
ELECTRICAL CHARACTERISTICS
Parameter1
Description
Test Conditions
Min
VOH2
High Level Output Voltage
@ VDD_EXT = min, IOH = –1.0 mA3
2.4
VOL2
Low Level Output Voltage
@ VDD_EXT = min, IOL = 1.0 mA3
Output Source DC Current
@ VOH_DDR2 (DC) = VDD_DDR2 -0.28 V
IOL_DDR2
Output Sink DC Current
@ VOL_DDR2 (DC)=0.28
TBD
mA
5, 6
High Level Input Current
@ VDD_EXT = max, VIN = VDD_EXT max
10
μA
IOH_DDR24
4
IIH
IIL5
Unit
V
0.4
TBD
V
mA
Low Level Input Current
@ VDD_EXT = max, VIN = 0 V
10
μA
Low Level Input Current Pull-up
@ VDD_EXT = max, VIN = 0 V
TBD
μA
7, 8
Three-State Leakage Current
@ VDD_EXT = max, VIN = VDD_EXT max
10
μA
7
Three-State Leakage Current
@ VDD_EXT = max, VIN = 0 V
10
μA
Three-State Leakage Current Pull-up @ VDD_EXT = max, VIN = 0 V
TBD
μA
Supply Current (Internal)
TBD
TBD
mA
Input Capacitance
TBD
TBD
pF
IOZH
IOZLPU8
9, 10
IDD-INTYP
CIN
Max
6
IILPU
IOZL
Typical
11, 12
1
Specifications subject to change without notice.
Applies to output and bidirectional pins: AMI_ADDR23-0, AMI_DATA7-0, AMI_RD, AMI_WR, FLAG3–0, DAI_Px, DPI_Px, EMU, TDO, CLKOUT.
3
See Output Drive Currents on Page 50 for typical drive current capabilities.
4
Applies to DDR2_ADDR18-0, DDR2_CAS, DDR2_CS3-0, DDR2_DQ1-0, DDR2_DM1-0, DDR2_DQS1-0, DDR2_DATA15-0, DDR2_RAS, DDR2_WE, DDR2_CLK0,
DDR2_CLK0, DDR2_CLK1 and, DDR2_CLK1.
5
Applies to input pins: BOOTCFGx, CLKCFGx, TCK, RESET, CLKIN.
6
Applies to input pins with 22.5 kΩ internal pull-ups: TRST, TMS, TDI.
7
Applies to three-statable pins: FLAG3–0.
8
Applies to three-statable pins with 22.5 kΩ pull-ups: DAI_Px, DPI_Px, EMU.
9
Typical internal current data reflects nominal operating conditions.
10
See Engineer-to-Engineer Note “Estimating Power Dissipation for ADSP-21469 SHARC Processors” for further information.
11
Applies to all signal pins.
12
Guaranteed, but not tested.
2
Rev. PrB
|
Page 17 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
MAXIMUM POWER DISSIPATION
ESD SENSITIVITY
See Engineer-to-Engineer Note “Estimating Power Dissipation
for ADSP-21469 SHARC Processors” for detailed thermal and
power information regarding maximum power dissipation. For
information on package thermal specifications, see Thermal
Characteristics on Page 51.
ESD (electrostatic discharge) sensitive device.
Charged devices and circuit boards can discharge
without detection. Although this product features
patented or proprietary protection circuitry, damage
may occur on devices subjected to high energy ESD.
Therefore, proper ESD precautions should be taken to
avoid performance degradation or loss of functionality.
ABSOLUTE MAXIMUM RATINGS
Stresses greater than those listed in Table 10 may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
Table 10. Absolute Maximum Ratings
Parameter
Internal (Core) Supply Voltage (VDD_INT)
Analog (PLL) Supply Voltage (VDD_A)
External (I/O) Supply Voltage (VDD_EXT)
DDR2 Controller Supply Voltage (VDD_DDR2)
Input Voltage
Output Voltage Swing
Load Capacitance
Storage Temperature Range
Junction Temperature under Bias
Rating
–0.3 V to +1.32V
TBD
–0.3 V to +4.6V
–0.5 V to +2.7V
–0.5 V to +3.8V
–0.5 V to VDD_EXT +0.5V
200 pF
–65°C to +150°C
125°C
Rev. PrB |
Page 18 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
TIMING SPECIFICATIONS
Page 15). To determine switching frequencies for the serial
ports, divide down the internal clock, using the programmable
divider control of each port (DIVx for the serial ports).
The ADSP-21469’s internal clock (a multiple of CLKIN) provides the clock signal for timing internal memory, processor
core, and serial ports. During reset, program the ratio between
the processor’s internal clock frequency and external (CLKIN)
clock frequency with the CLKCFG1–0 pins (see Table 9 on
Figure 3 shows core to CLKIN ratios of 6:1, 16:1, and 32:1 with
external oscillator or crystal. Note that more ratios are possible
and can be set through software using the power management
control register (PMCTL). For more information, see the
ADSP-2136x SHARC Processor Programming Reference.
LINKPORT
CLOCK
DIVIDER
CLK_CFGx/
PMCTL
BYPASS
MUX
PMCTL
LCLK
PMCTL
CLK_CFGx/
PMCTL
PLLI
CLKIN CLK
DIVIDER
LOOP
FILTER
VCO
PLL
DIVIDER
DDR2
DIVIDER
BYPASS
MUX
CLKIN
BYPASS
MUX
PLL
CCLK
XTAL
BUF
PMCTL
PLL
MULTIPLIER
DIVIDE
BY 2
CLK_CFGx/
PMCTL
DDR2_CLK
PCLK
PCLK
CLK_CFGx/PMCTL
CCLK
PMCTL
RESET
DELAY OF
4096 CLKIN
CYCLES
PIN MUX
CLKOUT
RESETOUT
BUF
RESETOUT/
CLKOUT
CORERST
Figure 3. Core Clock and System Clock Relationship to CLKIN
The ADSP-21469’s internal clock switches at higher frequencies
than the system input clock (CLKIN). To generate the internal
clock, the processor uses an internal phase-locked loop (PLL).
This PLL-based clocking minimizes the skew between the system clock (CLKIN) signal and the processor’s internal clock.
where:
Core clock frequency can be calculated as:
fINPUT = CLKIN when the input divider is disabled
fCCLK = (2 × PLLM × fINPUT) ÷ (2 × PLLN)
fVCO is the VCO frequency
PLLM is the multiplier value programmed
fINPUT is the input frequency to the PLL in MHz.
fINPUT = CLKIN ÷ 2 when the input divider is enabled
Note that in the user application, the PLL multiplier value
should be selected in such a way that the VCO frequency falls in
between 160 MHz and 800 MHz. The VCO frequency is calculated as follows:
Note the definitions of various clock periods shown in Table 12
which are a function of CLKIN and the appropriate ratio control shown in Table 11.
Table 11. CLKOUT and CCLK Clock Generation Operation
fVCO = 2 × PLLM × fINPUT
Timing
Requirements
CLKIN
CCLK
Rev. PrB |
Page 19 of 56 |
November 2008
Description
Input Clock
Core Clock
Calculation
1/tCK
1/tCCLK
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Table 12. Clock Periods
Timing
Requirements
tCK
tCCLK
tLCLK
tPCLK
tSCLK
tDDR2_CLK
tSPICLK
1
Description1
CLKIN Clock Period
(Processor) Core Clock Period
(Link Port) Core Clock Period
(Peripheral) Clock Period = 2 × tCCLK
Serial Port Clock Period = (tPCLK) × SR
DDR2 DRAM Clock Period = (tCCLK) × SDR
SPI Clock Period = (tPCLLK) × SPIR
where:
SR = serial port-to-core clock ratio (wide range, determined by SPORT CLKDIV
bits in DIVx register)
SPIR = SPI-to-Core Clock Ratio (wide range, determined by SPIBAUD register
setting)
SDR=DDR2 DRAM-to-Core Clock Ratio (Values determined by bits 20-18 of
the PMCTL register)
Rev. PrB |
Page 20 of 56 |
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results
for an individual device, the values given in this data sheet
reflect statistical variations and worst cases. Consequently, it is
not meaningful to add parameters to derive longer times. See
Figure 41 on Page 50 under Test Conditions for voltage reference levels.
Switching Characteristics specify how the processor changes its
signals. Circuitry external to the processor must be designed for
compatibility with these signal characteristics. Switching characteristics describe what the processor will do in a given
circumstance. Use switching characteristics to ensure that any
timing requirement of a device connected to the processor (such
as memory) is satisfied.
Timing Requirements apply to signals that are controlled by circuitry external to the processor, such as the data input for a read
operation. Timing requirements guarantee that the processor
operates correctly with other devices.
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Power-Up Sequencing
The timing requirements for processor startup are given in
Table 13.
Table 13. Power Up Sequencing Timing Requirements (Processor Startup)
Parameter
Timing Requirements
tRSTVDD
RESET Low Before VDDEXT or VDDDDR2 On
tEVDD-DDR2VDD
VDD_EXT on Before VDD_DDR2
tDDR2VDD_IVDD
VDD_DDR2 on Before VDD_INT
tCLKVDD1
CLKIN Valid After VDD_INT Valid
CLKIN Valid Before RESET Deasserted
tCLKRST
tPLLRST
PLL Control Setup Before RESET Deasserted
Switching Characteristic
tCORERST
Core Reset Deasserted After RESET Deasserted
Min
0
TBD
TBD
0
102
203
4096 × tCK + 2 × tCCLK 4, 5
1
Max
200
Unit
ms
ms
ms
ms
ms
ms
ms
Valid VDD_INT assumes that the supply is fully ramped to its 1 volt rail. Voltage ramp rates can vary from microseconds to hundreds of milliseconds depending on the design
of the power supply subsystem.
Assumes a stable CLKIN signal, after meeting worst-case startup timing of crystal oscillators. Refer to your crystal oscillator manufacturer's datasheet for startup time. Assume
a 25 ms maximum oscillator startup time if using the XTAL pin and internal oscillator circuit in conjunction with an external crystal.
3
Based on CLKIN cycles.
4
Applies after the power-up sequence is complete. Subsequent resets require a minimum of four CLKIN cycles for RESET to be held low in order to properly initialize and
propagate default states at all I/O pins.
5
The 4096 cycle count depends on tSRST specification in Table 15. If setup time is not met, one additional CLKIN cycle may be added to the core reset time, resulting in 4097
cycles maximum.
2
tR S T V D D
RESET
t E V D D -D D R 2V D D
V DDEXT
V DD_DDR2
tD D R 2V D D _IVD D
tC L K V D D
V DDINT
CLKIN
tC L K R S T
CLK_CFG 1-0
tC O R E R S T
t PL L R S T
RESETOUT
Figure 4. Power-Up Sequencing
Rev. PrB |
Page 21 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Clock Input
Table 14. Clock Input
450 MHz
Min
Parameter
Timing Requirements
tCK
CLKIN Period
tCKL
CLKIN Width Low
tCKH
CLKIN Width High
tCKRF
CLKIN Rise/Fall (0.4 V to 2.0 V)
tCCLK3
CCLK Period
TBD1
TBD1
TBD1
2.221
1
Applies only for CLKCFG1–0 = 00 and default values for PLL control bits in PMCTL.
Applies only for CLKCFG1–0 = 01 and default values for PLL control bits in PMCTL.
3
Any changes to PLL control bits in the PMCTL register must meet core clock timing specification tCCLK.
2
tCK
CLKIN
tCKH
tCKL
Figure 5. Clock Input
Clock Signals
The ADSP-21469 can use an external clock or a crystal. See the
CLKIN pin description in Table 6. The programmer can configure the ADSP-21469 to use its internal clock generator by
connecting the necessary components to CLKIN and XTAL.
Figure 6 shows the component connections used for a crystal
operating in fundamental mode. Note that the clock rate is
achieved using a 28.125 MHz crystal and a PLL multiplier ratio
16:1 (CCLK:CLKIN achieves a clock speed of 450 MHz). To
achieve the full core clock rate, programs need to configure the
multiplier bits in the PMCTL register.
ADSP-21469
R1
1M⍀*
CLKIN
XTAL
R2
47⍀*
C1
22pF
Y1
C2
22pF
28.125 MHz
R2 SHOULD BE CHOSEN TO LIMIT CRYSTAL
DRIVE POWER. REFER TO CRYSTAL
MANUFACTURER’S SPECIFICATIONS
*TYPICAL VALUES
Figure 6. 450 MHz Operation (Fundamental Mode Crystal)
Rev. PrB |
Page 22 of 56 |
November 2008
Max
Unit
TBD2
TBD2
TBD2
TBD
TBD
ns
ns
ns
ns
ns
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Reset
Table 15. Reset
Parameter
Timing Requirements
tWRST1
RESET Pulse Width Low
tSRST
RESET Setup Before CLKIN Low
1
Min
Max
Unit
TBD
TBD
TBD
TBD
ns
ns
Applies after the power-up sequence is complete. At power-up, the processor’s internal phase-locked loop requires no more than 100 μσ while RESET is low, assuming stable
VDD and CLKIN (not including start-up time of external clock oscillator).
CLKIN
tWRST
tSRST
RESET
Figure 7. Reset
Running Reset
The following timing specification applies to CLKOUT/
RESETOUT/RUNRSTIN pin when it is configured as
RUNRSTIN.
Table 16. Running Reset
Parameter
Timing Requirements
tWRUNRST
Running RESET Pulse Width Low
tSRUNRST
Running RESET Setup Before CLKIN High
Min
Max
Unit
TBD
TBD
TBD
TBD
ns
ns
CLKIN
tWRUNRST
tSRUNRST
RUNRSTIN
Figure 8. Running Reset
Rev. PrB |
Page 23 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Interrupts
The following timing specification applies to the FLAG0,
FLAG1, and FLAG2 pins when they are configured as IRQ0,
IRQ1, and IRQ2 interrupts as well as the DAI_P20-1 and
DPI_P14-1 pins when they are configured as interrupts.
Table 17. Interrupts
Parameter
Timing Requirement
tIPW
IRQx Pulse Width
DAI_P20-1
DPI_P14-1
FLAG2 -0
(IRQ2-0)
Min
Max
Unit
TBD
TBD
ns
tIPW
Figure 9. Interrupts
Core Timer
The following timing specification applies to FLAG3 when it is
configured as the core timer (CTIMER).
Table 18. Core Timer
Parameter
Switching Characteristic
tWCTIM
CTIMER Pulse Width
Min
Max
Unit
TBD
TBD
ns
tWCTIM
FLAG3
(CTIMER)
Figure 10. Core Timer
Timer PWM_OUT Cycle Timing
The following timing specification applies to Timer0 and
Timer1 in PWM_OUT (pulse-width modulation) mode. Timer
signals are routed to the DPI_P14–1 pins through the DPI SRU.
Therefore, the timing specifications provided below are valid at
the DPI_P14–1 pins.
Table 19. Timer PWM_OUT Timing
Parameter
Switching Characteristic
tPWMO
Timer Pulse Width Output
Min
Max
Unit
TBD
TBD
ns
tPWMO
DPI_P14-1
(TIMER1 -0)
Figure 11. Timer PWM_OUT Timing
Rev. PrB |
Page 24 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Timer WDTH_CAP Timing
The following timing specification applies to timer0 and timer1,
and in WDTH_CAP (pulse width count and capture) mode.
Timer signals are routed to the DPI_P14–1 pins through the
SRU. Therefore, the timing specification provided below is valid
at the DPI_P14–1 pins.
Table 20. Timer Width Capture Timing
Parameter
Timing Requirement
tPWI
Timer Pulse Width
Min
Max
Unit
TBD
TBD
ns
tPWI
DPI_P14-1
(TIMER1-0)
Figure 12. Timer Width Capture Timing
Pin to Pin Direct Routing (DAI and DPI)
For direct pin connections only (for example DAI_PB01_I to
DAI_PB02_O).
Table 21. DAI Pin to Pin Routing
Parameter
Timing Requirement
tDPIO
Delay DAI/DPI Pin Input Valid to DAI Output Valid
Min
Max
Unit
TBD
TBD
ns
DAI_Pn
DPI_Pn
DAI_Pm
DPI_Pm
tDPIO
Figure 13. DAI Pin to Pin Direct Routing
Rev. PrB |
Page 25 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
inputs and outputs are not directly routed to/from DAI pins (via
pin buffers) there is no timing data available. All timing parameters and switching characteristics apply to external DAI pins
(DAI_P01 – DAI_P20).
Precision Clock Generator (Direct Pin Routing)
This timing is only valid when the SRU is configured such that
the precision clock generator (PCG) takes its inputs directly
from the DAI pins (via pin buffers) and sends its outputs
directly to the DAI pins. For the other cases, where the PCG’s
Table 22. Precision Clock Generator (Direct Pin Routing)
Parameter
Min
Max
Unit
Timing Requirements
tPCGIW
Input Clock Period
TBD
TBD
ns
tSTRIG
PCG Trigger Setup Before Falling Edge of PCG Input TBD
TBD
ns
Clock
tHTRIG
PCG Trigger Hold After Falling Edge of PCG Input
TBD
TBD
ns
Clock
Switching Characteristics
tDPCGIO
PCG Output Clock and Frame Sync Active Edge Delay
After PCG Input Clock
TBD
TBD
ns
tDTRIGCLK
PCG Output Clock Delay After PCG Trigger
TBD
TBD
ns
tDTRIGFS
PCG Frame Sync Delay After PCG Trigger
TBD
TBD
ns
tPCGOW1
Output Clock Period
TBD
TBD
ns
D = FSxDIV, PH = FSxPHASE. For more information, see the ADSP-2146x SHARC Processor Hardware Reference, “Precision Clock Generators”
chapter.
1
Normal mode of operation.
tSTRIG
tHTRIG
DAI_Pn
DPI_Pn
PCG_TRIGx_I
tPCGIW
DAI_Pm
DPI_Pm
PCG_EXTx_I
(CLKIN)
tDPCGIO
DAI_Py
DPI_Py
PCG_CLKx_O
tDTRIGCLK
tDPCGIO
DAI_Pz
DPI_Pz
PCG_FSx_O
tDTRIGFS
Figure 14. Precision Clock Generator (Direct Pin Routing)
Rev. PrB |
Page 26 of 56 |
November 2008
tPCGOW
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Flags
The timing specifications provided below apply to
AMI_ADDR23-0 and AMI_DATA7-0 when configured as
FLAGS. See Table 6 on page 12 for more information on flag
use.
Table 23. Flags
Parameter
Min
Timing Requirement
tFIPW
DPI_P14-1, AMI_ADDR23-0, AMI_DATA7-0, FLAG3–0 IN Pulse Width TBD
Switching Characteristic
DPI_P14-1, AMI_ADDR23-0, AMI_DATA7-0, FLAG3–0 OUT Pulse Width TBD
tFOPW
DPI_P14-1
(FLAG3- 0IN)
(AMI_DATA7- 0)
(AMI_ADDR23-0)
tFIPW
DPI_P14-1
(FLAG3-0OUT)
(AMI_DATA7- 0)
AMI_ADDR23-0)
tFOPW
Figure 15. Flags
Rev. PrB |
Page 27 of 56 |
November 2008
Max
Unit
TBD
ns
TBD
ns
ADSP-21469/ADSP-21469W
Preliminary Technical Data
DDR2 SDRAM Read Cycle Timing
Table 24. DDR2 SDRAM Read Cycle Timing, VDD-DDR2 nominal 1.8V
Parameter
Timing Requirements
TBD
Symbol
Minimum
Maximum
Unit
TBD
TBD
TBD
TBD
TBD
Figure 16. DDR2 SDRAM Controller Input AC Timing
Rev. PrB |
Page 28 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
DDR2 SDRAM Write Cycle Timing
Table 25. DDR2 SDRAM Write Cycle Timing, VDD-DDR2 nominal 1.8V
Parameter
Switching Characteristics
TBD
Symbol
Minimum
Maximum
Unit
TBD
TBD
TBD
TBD
TBD
Figure 17. DDR2 SDRAM Controller Output AC Timing
Rev. PrB |
Page 29 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Memory Read—Bus Master
Use these specifications for asynchronous interfacing to memories. Note that timing for AMI_ACK, AMI_DATA, AMI_RD,
AMI_WR, and strobe timing parameters only apply to asynchronous access mode.
Table 26. Memory Read—Bus Master
Parameter
Min
Timing Requirements
tDAD
Address, Selects Delay to Data Valid1, 2
TBD
tDRLD
AMI_RD Low to Data Valid1
TBD
tSDS
Data Setup to AMI_RD High
TBD
tHDRH
Data Hold from AMI_RD High3, 4
TBD
tDAAK
AMI_ACK Delay from Address, Selects2, 5
TBD
tDSAK
AMI_ACK Delay from AMI_RD Low4
TBD
Switching Characteristics
TBD
tDRHA
Address Selects Hold After AMI_RD High
TBD
tDARL
Address Selects to AMI_RD Low2
TBD
tRW
AMI_RD Pulse Width
TBD
tRWR
AMI_RD High to AMI_WR, AMI_RD, Low
TBD
W = (number of wait states specified in AMICTLx register) × tDDR2_CLK.
HI = RHC + IC (RHC = (number of Read Hold Cycles specified in AMICTLx register) x tDDR2_CLK
IC = (number of idle cycles specified in AMICTLx register) x tDDR2_CLK).
H = (number of hold cycles specified in AMICTLx register) x tDDR2_CLK.
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
1
Data delay/setup: System must meet tDAD, tDRLD, or tSDS.
The falling edge of AMI_MSx, is referenced.
3
Note that timing for AMI_ACK, AMI_DATA, AMI_RD, AMI_WR, and strobe timing parameters only apply to asynchronous access mode.
4
Data hold: User must meet tHDRH in asynchronous access mode. See Test Conditions on Page 50 for the calculation of hold times given capacitive and dc loads.
5
AMI_ACK delay/setup: User must meet tDAAK, or tDSAK, for deassertion of AMI_ACK (low). For asynchronous assertion of AMI_ACK (high) user must meet tDAAK or tDSAK.
2
AMI_ADDR
MSx
AMI_RD
tDRHA
tDARL
tRW
tDRLD
tSDS
tDAD
tHDRH
AMI_DATA
tDSAK
tDAAK
tRWR
AMI_ACK
AMI_WR
Figure 18. Memory Read—Bus Master
Rev. PrB |
Page 30 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Memory Write—Bus Master
Use these specifications for asynchronous interfacing to memories. Note that timing for AMI_ACK, AMI_DATA, AMI_RD,
AMI_WR, and strobe timing parameters only apply to asynchronous access mode.
Table 27. Memory Write—Bus Master
Parameter
Min
Max
Unit
Timing Requirements
tDAAK
AMI_ACK Delay from Address, Selects1, 2
TBD
TBD
ns
1, 3
tDSAK
AMI_ACK Delay from AMI_WR Low
TBD
TBD
ns
Switching Characteristics
TBD
TBD
tDAWH
Address, Selects to AMI_WR Deasserted2
TBD
TBD
ns
2
tDAWL
Address, Selects to AMI_WR Low
TBD
TBD
ns
tWW
AMI_WR Pulse Width
TBD
TBD
ns
tDDWH
Data Setup Before AMI_WR High
TBD
TBD
ns
tDWHA
Address Hold After AMI_WR Deasserted
TBD
TBD
ns
Data Hold After AMI_WR Deasserted
TBD
TBD
ns
tDWHD
tDATRWH
Data Disable After AMI_WR Deasserted4
TBD
TBD
ns
tWWR
AMI_WR High to AMI_WR, AMI_RD Low
TBD
TBD
ns
tDDWR
Data Disable Before AMI_RD Low
TBD
TBD
ns
tWDE
AMI_WR Low to Data Enabled
TBD
TBD
ns
W = (number of wait states specified in AMICTLx register) × tSDDR2_CLKH = (number of hold cycles specified in AMICTLx register) x tDDR2_CLK
1
AMI_ACK delay/setup: System must meet tDAAK, or tDSAK, for deassertion of AMI_ACK (low). For asynchronous assertion of AMI_ACK (high) user must meet tDAAK or tDSAK.
The falling edge of AMI_MSx is referenced.
3
Note that timing for AMI_ACK, AMI_DATA, AMI_RD, AMI_WR, and strobe timing parameters only applies to asynchronous access mode.
4
See Test Conditions on Page 50 for calculation of hold times given capacitive and dc loads.
2
AMI_ADDR
MSx
tDAWH
tDAWL
tDWHA
tWW
AMI_WR
tWWR
tWDE
tDATRWH
tDDWH
tDDWR
AMI_DATA
tDSAK
tDWHD
tDAAK
AMI_ACK
AMI_RD
Figure 19. Memory Write—Bus Master
Rev. PrB |
Page 31 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
from speed specifications will result in unrealistically small skew
times because they include multiple tester guardbands. The
setup and hold skew times shown below are calculated to
include only one tester guardband.
Link Ports
Calculation of link receiver data setup and hold relative to link
clock is required to determine the maximum allowable skew
that can be introduced in the transmission path between
LDATA and LCLK. Setup skew is the maximum delay that can
be introduced in LDATA relative to LCLK, (setup skew = tLCLKTWH min– tDLDCH – tSLDCL). Hold skew is the maximum delay
that can be introduced in LCLK relative to LDATA, (hold skew
= tLCLKTWL min – tHLDCH – tHLDCL). Calculations made directly
ADSP-21469 Setup Skew = TBD ns max
ADSP-21469 Hold Skew = TBD ns max
Note that there is a two-cycle effect latency between the link
port enable instruction and the DSP enabling the link port.
Table 28. Link Ports – Receive
Parameter
Timing Requirements
tSLDCL
Data Setup Before LCLK Low
tHLDCL
Data Hold After LCLK Low
tLCLKIW
LCLK Period
tLCLKRWL
LCLK Width Low
LCLK Width High
tLCLKRWH
Switching Characteristics
tDLALC
LACK Low Delay After LCLK High1
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
LACK goes low with tDLALC relative to rise of LCLK after first byte, but does not go low if the receiver's link buffer is not about to fill.
tLCLKIW
tLCLKRWH
tLCLKRWL
LCLK
tSLDCL
LDAT7-0
tHLDCL
IN
tDLALC
LACK (OUT)
Figure 20. Link Ports—Receive
Rev. PrB |
Page 32 of 56 |
November 2008
ns
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Table 29. Link Ports – Transmit
Parameter
Timing Requirements
tSLACH
LACK Setup Before LCLK High
LACK Hold After LCLK High
tHLACH
Switching Characteristics
tDLDCH
Data Delay After LCLK High
tHLDCH
Data Hold After LCLK High
tLCLKTWL
LCLK Width Low
tLCLKTWH
LCLK Width High
tDLACLK
LCLK Low Delay After LACK High
tLCLKTWH
tLCLKTWL
LAST BYTE
TRANSMITTED
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
FIRST BYTE
TRANSMITTED
ns
ns
ns
ns
ns
LCLK INACTIVE
(HIGH)
LCLK
tDLDCH
tHLDCH
LDAT7-0
OUT
tSLACH
tHLACH
LACK (IN)
THE tSLACH REQUIREMENT APPLIES TO THE RISING EDGE OF LCLK ONLY FOR THE FIRST BYTE TRANSMITTED.
Figure 21. Link Ports—Transmit
Rev. PrB |
Page 33 of 56 |
November 2008
tDLACLK
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Serial Ports
To determine whether communication is possible between two
devices at clock speed n, the following specifications must be
confirmed: 1) frame sync delay and frame sync setup and hold,
2) data delay and data setup and hold, and 3) SCLK width.
Serial port signals (SCLK, FS, Data Channel A, Data Channel B)
are routed to the DAI_P20–1 pins using the SRU. Therefore, the
timing specifications provided below are valid at the
DAI_P20–1 pins.
Table 30. Serial Ports—External Clock
Parameter
Timing Requirements
tSFSE1
FS Setup Before SCLK
(Externally Generated FS in either Transmit or Receive Mode)
tHFSE1
FS Hold After SCLK
(Externally Generated FS in either Transmit or Receive Mode)
1
tSDRE
Receive Data Setup Before Receive SCLK
tHDRE1
Receive Data Hold After SCLK
tSCLKW
SCLK Width
tSCLK
SCLK Period
Switching Characteristics
tDFSE2
FS Delay After SCLK
(Internally Generated FS in either Transmit or Receive Mode)
FS Hold After SCLK
tHOFSE2
(Internally Generated FS in either Transmit or Receive Mode)
tDDTE2
Transmit Data Delay After Transmit SCLK
2
Transmit Data Hold After Transmit SCLK
tHDTE
1
2
Min
Max
Unit
TBD
TBD
ns
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
TBD
ns
TBD
TBD
TBD
ns
ns
ns
TBD
TBD
TBD
Referenced to sample edge.
Referenced to drive edge.
Table 31. Serial Ports—Internal Clock
Parameter
Timing Requirements
tSFSI1
FS Setup Before SCLK
(Externally Generated FS in either Transmit or Receive Mode)
tHFSI1
FS Hold After SCLK
(Externally Generated FS in either Transmit or Receive Mode)
tSDRI1
Receive Data Setup Before SCLK
1
tHDRI
Receive Data Hold After SCLK
Switching Characteristics
tDFSI2
FS Delay After SCLK (Internally Generated FS in Transmit Mode)
tHOFSI2
FS Hold After SCLK (Internally Generated FS in Transmit Mode)
2
tDFSIR
FS Delay After SCLK (Internally Generated FS in Receive Mode)
tHOFSIR2
FS Hold After SCLK (Internally Generated FS in Receive Mode)
tDDTI2
Transmit Data Delay After SCLK
2
tHDTI
Transmit Data Hold After SCLK
tSCKLIW
Transmit or Receive SCLK Width
1
2
Referenced to the sample edge.
Referenced to drive edge.
Rev. PrB |
Page 34 of 56 |
November 2008
Min
Max
Unit
TBD
TBD
ns
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Table 32. Serial Ports—Enable and Three-State
Parameter
Switching Characteristics
tDDTEN1
Data Enable from External Transmit SCLK
Data Disable from External Transmit SCLK
tDDTTE1
tDDTIN1
Data Enable from Internal Transmit SCLK
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
Parameter
Min
Switching Characteristics
tDDTLFSE1
Data Delay from Late External Transmit FS or External Receive FS
with MCE = 1, MFD = 0
TBD
tDDTENFS1
Data Enable for MCE = 1, MFD = 0
TBD
Max
Unit
TBD
TBD
ns
ns
Referenced to drive edge.
Table 33. Serial Ports—External Late Frame Sync
1
The tDDTLFSE and tDDTENFS parameters apply to left-justified sample pair as well as DSP serial mode, and MCE = 1, MFD = 0.
EXTERNAL RECEIVE FS WITH MCE = 1, MFD = 0
DAI_P20 -1
(SCLK)
SAMPLE
DRIVE
DRIVE
tSFSE/I
tHFSE/I
DAI_P20 -1
(FS)
tDDTE/I
tDDTENFS
tHDTE/I
DAI_P20 -1
(DATA CHANNEL A/B)
2ND BIT
1ST BIT
tD DTLFSE
LATE EXTERNAL TRANSMIT FS
DAI_P20-1
(SCLK)
SAMPLE
DRIVE
tSFSE/I
DRIVE
tHFSE/I
DAI_P20 -1
(FS)
tDDTE/I
tDDTENFS
tHDTE/I
DAI_P20 -1
(DATA CHANNEL A/B)
1ST BIT
2ND BIT
tDDTLFSE
NOTE: SERIAL PORT SIGNALS (SCLK, FS, DATA CHANNEL A/B) ARE ROUTED TO THE DAI_P20 -1 PINS
USING THE SRU. THE TIMING SPECIFICATIONS PROVIDED HERE ARE VALID AT THE DAI_P20 -1 PINS.
THE CHARACTERIZED AC SPORT TIMINGS ARE APPLICABLE WHEN INTERNAL CLOCKS AND FRAMES
ARE LOOPED BACK FROM THE PIN, NOT ROUTED DIRECTLY THROUGH SAU.
Figure 22. External Late Frame Sync1
1
This figure reflects changes made to support left-justified sample pair mode.
Rev. PrB |
Page 35 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
DATA RECEIVE—INTERNAL CLOCK
DRIVE EDGE
DATA RECEIVE—EXTERNAL CLOCK
SAMPLE EDGE
DRIVE EDGE
SAMPLE EDGE
tSCLKIW
tSCLKW
DAI_P20-1
(SCLK)
DAI_P20- 1
(SCLK)
tDFSIR
tDFSE
tHFSI
tSFSI
tHOFSIR
DAI_P20-1
(FS)
tHFSE
tSFSE
tHOFSE
DAI_P20-1
(FS)
tSDRI
tHDRI
DAI_P20-1
(DATA CHANNEL A/B)
tSDRE
tHDRE
DAI_P20-1
(DATA CHANNEL A/B)
NOTE: EITHER THE RISING EDGE OR FALLING EDGE OF SCLK (EXTERNAL) OR SCLK (INTERNAL) CAN BE USED AS THE ACTIVE SAMPLING EDGE.
DATA TRANSMIT—INTERNAL CLOCK
DRIVE EDGE
DATA TRANSMIT—EXTERNAL CLOCK
SAMPLE EDGE
DRIVE EDGE
SAMPLE EDGE
tSCLKIW
tSCLKW
DAI_P20- 1
(SCLK)
DAI_P20- 1
(SCLK)
tDFSI
tDFSE
tHOFSI
tHFSI
tSFSI
DAI_P20- 1
(FS)
tHOFSE
tSFSE
tHFSE
DAI_P20-1
(FS)
tDDTI
tHDTI
tHDTE
DAI_P20-1
(DATA CHANNEL A/B)
tDDTE
DAI_P20- 1
(DATA CHANNEL A/B)
NOTE: EITHER THE RISING EDGE OR FALLING EDGE OF SCLK (EXTERNAL) OR SCLK (INTERNAL) CAN BE USED AS THE ACTIVE SAMPLING EDGE.
DRIVE EDGE
DRIVE EDGE
SCLK
DAI_P20-1
SCLK (EXT)
tDDTEN
tDDTTE
DAI_P20-1
(DATA CHANNEL A/B)
DRIVE EDGE
DAI_P20-1
SCLK (INT)
tDDTIN
DAI_P20-1
(DATA CHANNEL A/B)
Figure 23. Serial Ports
Rev. PrB |
Page 36 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Input Data Port (IDP)
The timing requirements for the IDP are given in Table 34. IDP
signals (SCLK, FS, and SDATA) are routed to the DAI_P20–1
pins using the SRU. Therefore, the timing specifications provided below are valid at the DAI_P20–1 pins.
Table 34. Input Data Port (IDP)
Parameter
Timing Requirements
tSISFS1
FS Setup Before SCLK Rising Edge
1
tSIHFS
FS Hold After SCLK Rising Edge
SData Setup Before SCLK Rising Edge
tSISD1
tSIHD1
SData Hold After SCLK Rising Edge
tIDPCLKW
Clock Width
tIDPCLK
Clock Period
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
AMI_DATA, SCLK, FS can come from any of the DAI pins. SCLK and FS can also come via PCG or SPORTs. PCG's input can be either CLKIN or any of the DAI pins.
SAMPLE EDGE
tIPDCLK
tIPDCLKW
DAI_P20-1
(SCLK)
tSISFS
tSIHFS
DAI_P20-1
(FS)
tSISD
tSIHD
DAI_P20-1
(SDATA)
Figure 24. IDP Master Timing
Sample Rate Converter—Serial Input Port
The ASRC input signals (SCLK, FS, and SDATA) are routed
from the DAI_P20–1 pins using the SRU. Therefore, the timing
specifications provided in Table 35 are valid at the DAI_P20–1
pins.
Table 35. ASRC, Serial Input Port
Parameter
Timing Requirements
FS Setup Before SCLK Rising Edge
tSRCSFS1
1
tSRCHFS
FS Hold After SCLK Rising Edge
tSRCSD1
SDATA Setup Before SCLK Rising Edge
tSRCHD1
SDATA Hold After SCLK Rising Edge
tSRCCLKW
Clock Width
tSRCCLK
Clock Period
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
AMI_DATA, SCLK, FS can come from any of the DAI pins. SCLK and FS can also come via PCG or SPORTs. PCG’s input can be either CLKIN or any of the DAI pins.
Rev. PrB |
Page 37 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
SAMPLE EDGE
tSRCCLK
DAI_P20-1
(SCLK)
tSRCCLKW
tSRCSFS
tSRCHFS
DAI_P20-1
(FS)
tSRCSD
tSRCHD
DAI_P20-1
(SDATA)
Figure 25. ASRC Serial Input Port Timing
Rev. PrB |
Page 38 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
and delay specification with regard to SCLK. Note that SCLK
rising edge is the sampling edge and the falling edge is the
drive edge.
Sample Rate Converter—Serial Output Port
For the serial output port, the frame-sync is an input and it
should meet setup and hold times with regard to SCLK on the
output port. The serial data output, SDATA, has a hold time
Table 36. ASRC, Serial Output Port
Parameter
Timing Requirements
FS Setup Before SCLK Rising Edge
tSRCSFS1
tSRCHFS1
FS Hold After SCLK Rising Edge
tSRCCLKW
Clock Width
tSRCCLK
Clock Period
Switching Characteristics
tSRCTDD1
Transmit Data Delay After SCLK Falling Edge
1
Transmit Data Hold After SCLK Falling Edge
tSRCTDH
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
AMI_DATA, SCLK, and FS can come from any of the DAI pins. SCLK and FS can also come via PCG or SPORTs. PCG’s input can be either CLKIN or any of the DAI pins.
SAMPLE EDGE
tSRCCLK
tSRCCLKW
DAI_P20- 1
(SCLK)
tSRCSFS
tSRCHFS
DAI_P20- 1
(FS)
tSRCTDD
DAI_P20-1
(SDATA)
tSRCTDH
Figure 26. ASRC Serial Output Port Timing
Rev. PrB |
Page 39 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Reference. Note that the most significant 16 bits of external
PDAP data can be provided through the DATA7-0 pins. The
remaining four bits can only be sourced through DAI_P4–1.
The timing below is valid at the DATA7–0 pins.
Parallel Data Acquisition Port (PDAP)
The timing requirements for the PDAP are provided in
Table 37. PDAP is the parallel mode operation of Channel 0 of
the IDP. For details on the operation of the PDAP, see the
PDAP chapter of the ADSP-2146x SHARC Processor Hardware
Table 37. Parallel Data Acquisition Port (PDAP)
Parameter
Timing Requirements
tSPCLKEN1
PDAP_CLKEN Setup Before PDAP_CLK Sample Edge
1
tHPCLKEN
PDAP_CLKEN Hold After PDAP_CLK Sample Edge
PDAP_DAT Setup Before SCLK PDAP_CLK Sample Edge
tPDSD1
tPDHD1
PDAP_DAT Hold After SCLK PDAP_CLK Sample Edge
tPDCLKW
Clock Width
tPDCLK
Clock Period
Switching Characteristics
tPDHLDD
Delay of PDAP Strobe After Last PDAP_CLK Capture Edge for a Word
PDAP Strobe Pulse Width
tPDSTRB
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
ns
ns
Source pins of AMI_DATA are DATA7–0 or DAI pins. Source pins for SCLK and FS are: 1) DAI pins, 2) CLKIN through PCG, or 3) DAI pins through PCG.
SAMPLE EDGE
t PDCLK
t PDCLKW
DAI_P20 -1
(PDAP_CLK)
t SPCLKEN
t HPCLKEN
DAI_P20- 1
(PDAP_CLKEN)
t PDSD
t PDHD
DATA
DAI_P20-1
(PDAP_STROBE)
tPDSTRB
t PDHLDD
Figure 27. PDAP Timing
Rev. PrB |
Page 40 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Pulse-Width Modulation Generators (PWM)
The following timing specifications apply when the
AMI_ADDR23-8 pins are configured as PWM.
Table 38. Pulse-Width Modulation (PWM) Timing
Parameter
Switching Characteristics
tPWMW
PWM Output Pulse Width
tPWMP
PWM Output Period
Min
Max
Unit
TBD
TBD
TBD
TBD
ns
ns
tPWMW
PWM
OUTPUTS
tPWMP
Figure 28. PWM Timing
Rev. PrB |
Page 41 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
S/PDIF Transmitter
Serial data input to the S/PDIF transmitter can be formatted as
left justified, I2S, or right justified with word widths of 16-, 18-,
20-, or 24-bits. The following sections provide timing for the
transmitter.
S/PDIF Transmitter-Serial Input Waveforms
Figure 29 shows the right-justified mode. LRCLK is high for the
left channel and low for the right channel. Data is valid on the
rising edge of SCLK. The MSB is delayed 12-bit clock periods
(in 20-bit output mode) or 16-bit clock periods (in 16-bit output
DAI_P20-1
LRCLK
mode) from an LRCLK transition, so that when there are 64
SCLK periods per LRCLK period, the LSB of the data will be
right-justified to the next LRCLK transition.
RIGHT CHANNEL
LEFT CHANNEL
DAI_P20-1
SCLK
DAI_P20-1
SDATA
LSB
MSB
MS B-1
MSB-2
LSB+2 LSB+1
LSB
MSB
MSB-1
MSB-2
LSB+2
LSB+1
LSB
Figure 29. Right-Justified Mode
Figure 30 shows the default I2S-justified mode. LRCLK is low
for the left channel and HI for the right channel. Data is valid on
the rising edge of SCLK. The MSB is left-justified to an LRCLK
transition but with a single SCLK period delay.
RIGHT CHANNEL
DAI_P20-1
LRCLK
LEFT CHANNEL
DAI_P20-1
SCLK
DAI_P20-1
SDATA
MSB
MSB-1
MS B-2
LSB+2 LSB+1
LSB
MSB
MS B-1
MSB-2
LSB+2
LSB+1
LSB
MSB
Figure 30. I2S-Justified Mode
Figure 31 shows the left-justified mode. LRCLK is high for the
left channel and LO for the right channel. Data is valid on the
rising edge of SCLK. The MSB is left-justified to an LRCLK
transition with no MSB delay.
DAI_P20-1
LRCLK
RIGHT CHANNEL
LEFT CHANNEL
DAI_P20-1
SCLK
DAI_P20-1
SDATA
MSB
MSB-1
MSB-2
LS B+2
LSB+1
LSB
MSB
MSB-1
MSB-2
Figure 31. Left-Justified Mode
Rev. PrB |
Page 42 of 56 |
November 2008
LSB+2
LSB +1
LSB
MSB
MSB+1
Preliminary Technical Data
ADSP-21469/ADSP-21469W
S/PDIF Transmitter Input Data Timing
The timing requirements for the S/PDIF transmitter are given
in Table 39. Input signals (SCLK, FS, SDATA) are routed to the
DAI_P20–1 pins using the SRU. Therefore, the timing specifications provided below are valid at the DAI_P20–1 pins.
Table 39. S/PDIF Transmitter Input Data Timing
Parameter
Timing Requirements
tSISFS1
FS Setup Before SCLK Rising Edge
tSIHFS1
FS Hold After SCLK Rising Edge
tSISD1
SData Setup Before SCLK Rising Edge
tSIHD1
SData Hold After SCLK Rising Edge
Transmit Clock Width
tSITXCLKW
tSITXCLK
Transmit Clock Period
tSISCLKW
Clock Width
tSISCLK
Clock Period
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
ns
ns
AMI_DATA, SCLK, FS can come from any of the DAI pins. SCLK and FS can also come via PCG or SPORTs. PCG’s input can be either CLKIN or any of the DAI pins.
tSITXCLKW
SAMPLE EDGE
tSITXCLK
DAI_P20-1
(TXCLK)
tSISCLKW
DAI_P20-1
(SCLK)
tSISCLK
tSIHFS
tSISFS
DAI_P20-1
(FS)
tSISD
tSIHD
DAI_P20-1
(SDATA)
Figure 32. S/PDIF Transmitter Input Timing
Oversampling Clock (TxCLK) Switching Characteristics
The S/PDIF transmitter has an oversampling clock. This TxCLK
input is divided down to generate the biphase clock.
Table 40. Over Sampling Clock (TxCLK) Switching Characteristics
Parameter
TxCLK Frequency for TxCLK = 384 × FS
TxCLK Frequency for TxCLK = 256 × FS
Frame Rate
Min
TBD
TBD
TBD
Rev. PrB |
Page 43 of 56 |
November 2008
Max
TBD
TBD
TBD
Unit
MHz
MHz
kHz
ADSP-21469/ADSP-21469W
Preliminary Technical Data
S/PDIF Receiver
The following section describes timing as it relates to the
S/PDIF receiver.
Internal Digital PLL Mode
In the internal digital phase-locked loop mode the internal PLL
(digital PLL) generates the TBD × FS clock.
Table 41. S/PDIF Receiver Internal Digital PLL Mode Timing
Parameter
Switching Characteristics
LRCLK Delay After SCLK
tDFSI
tHOFSI
LRCLK Hold After SCLK
tDDTI
Transmit Data Delay After SCLK
tHDTI
Transmit Data Hold After SCLK
tSCLKIW1
Transmit SCLK Width
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
SCLK frequency is TBD x FS where FS = the frequency of LRCLK.
DRIVE EDGE
SAMPLE EDGE
tSCLKIW
DAI_P20-1
(SCLK)
tDFSI
tHOFSI
DAI_P20-1
(FS)
tHDTI
tDDTI
DAI_P20-1
(DATA CHANNEL A/B)
Figure 33. S/PDIF Receiver Internal Digital PLL Mode Timing
Rev. PrB |
Page 44 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
SPI Interface—Master
The ADSP-21469 contains two SPI ports. Both primary and secondary are available through DPI only. The timing provided in
Table 42 and Table 43 applies to both.
Table 42. SPI Interface Protocol—Master Switching and Timing Specifications
Parameter
Timing Requirements
Data Input Valid To SPICLK Edge (Data Input Setup Time)
tSSPIDM
tHSPIDM
SPICLK Last Sampling Edge To Data Input Not Valid
Switching Characteristics
tSPICLKM
Serial Clock Cycle
tSPICHM
Serial Clock High Period
tSPICLM
Serial Clock Low Period
SPICLK Edge to Data Out Valid (Data Out Delay Time)
tDDSPIDM
tHDSPIDM
SPICLK Edge to Data Out Not Valid (Data Out Hold Time)
tSDSCIM
FLAG3–0IN (SPI device select) Low to First SPICLK Edge
tHDSM
Last SPICLK Edge to FLAG3–0IN High
tSPITDM
Sequential Transfer Delay
Min
Max
Unit
TBD
TBD
TBD
TBD
ns
ns
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
FLAG3-0
(OUTPUT)
t S DSCIM
t SPICHM
t SPICLM
t SPICL M
t SPICHM
t SPI CLKM
t HDSM
t SPIT DM
SPICLK
(CP = 0)
(OUTPUT)
SPICLK
(CP = 1)
(OUTPUT)
t HDSPIDM
t D DSPIDM
MOSI
(OUTPUT)
MSB
LSB
t SSPIDM
CPHASE = 1
t SS PIDM
MISO
(INPUT)
MSB
VALID
LSB
VALID
t DDSPIDM
MOSI
(OUTPUT)
CPHASE = 0
MISO
(INPUT)
tHS PIDM
t HSPIDM
t HDSPIDM
MSB
t SS PIDM
LSB
t HSPIDM
MSB
VALID
LSB
VALID
Figure 34. SPI Master Timing
Rev. PrB |
Page 45 of 56 |
November 2008
ns
ns
ns
ns
ADSP-21469/ADSP-21469W
Preliminary Technical Data
SPI Interface—Slave
Table 43. SPI Interface Protocol—Slave Switching and Timing Specifications
Parameter
Timing Requirements
tSPICLKS
tSPICHS
tSPICLS
tSDSCO
Serial Clock Cycle
Serial Clock High Period
Serial Clock Low Period
SPIDS Assertion to First SPICLK Edge
CPHASE = 0
CPHASE = 1
Last SPICLK Edge to SPIDS Not Asserted, CPHASE = 0
tHDS
tSSPIDS
Data Input Valid to SPICLK edge (Data Input Set-up Time)
tHSPIDS
SPICLK Last Sampling Edge to Data Input Not Valid
tSDPPW
SPIDS Deassertion Pulse Width (CPHASE=0)
Switching Characteristics
tDSOE
SPIDS Assertion to Data Out Active
SPIDS Deassertion to Data High Impedance
tDSDHI
tDDSPIDS
SPICLK Edge to Data Out Valid (Data Out Delay Time)
tHDSPIDS
SPICLK Edge to Data Out Not Valid (Data Out Hold Time)
tDSOV
SPIDS Assertion to Data Out Valid (CPHAS E = 0)
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
SPIDS
(INPUT)
t S P IC H S
tSPICLS
tSPICLKS
tHDS
SPICLK
(CP = 0)
(INPUT)
tSPICLS
tSDSCO
SPICLK
(CP = 1)
(INPUT)
tSPICHS
tDSDHI
tDDSPIDS
tDSOE
tSDPPW
tDDSPIDS
MISO
(OUTPUT)
tHDSPIDS
MSB
LSB
tHSPIDS
CPHASE = 1
tSSPIDS
tSSPIDS
MOSI
(INPUT)
MSB VALID
LSB VALID
tHDSPIDS
tDDSPIDS
MISO
(OUTPUT) t
DSOV
MSB
LSB
CPHASE = 0
MOSI
(INPUT)
tHSPIDS
tSSPIDS
MSB VALID
LSB VALID
Figure 35. SPI Slave Timing
Rev. PrB |
Page 46 of 56 |
November 2008
tDSDHI
Preliminary Technical Data
ADSP-21469/ADSP-21469W
Universal Asynchronous Receiver-Transmitter
(UART) Port—Receive and Transmit Timing
Figure 36 describes UART port receive and transmit operations.
The maximum baud rate is PCLK/16 where PCLK = 1/tPCLK.
As shown in Figure 36 there is some latency between the gener-
ation of internal UART interrupts and the external data
operations. These latencies are negligible at the data transmission rates for the UART.
Table 44. UART Port
Parameter
Timing Requirement
Incoming Data Pulse Width
tRXD1
Switching Characteristic
tTXD1
Outgoing Data Pulse Width
1
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
UART signals RXD and TXD are routed through DPI P14-1 pins using the SRU.
DPI_P14-1
[RXD]
DATA(5- 8)
STOP
RECEIVE
tRXD
INTERNAL
UART RECEIVE
INTERRUPT
UART RECEIVE BIT SET BY DATA STOP;
CLEARED BY FIFO READ
START
DPI_P14-1
[TXD]
TRANSMIT
DATA(5- 8)
STOP(1-2)
tTXD
INTERNAL
UART TRANSMIT
INTERRUPT
UART TRANSMIT BIT SET BY PROGRAM;
CLEARED BY WRITE TO TRANSMIT
Figure 36. UART Port—Receive and Transmit Timing
Rev. PrB |
Page 47 of 56 |
November 2008
ADSP-21469/ADSP-21469W
Preliminary Technical Data
TWI Controller Timing
Table 45 and Figure 37 provide timing information for the TWI
interface. Input Signals (SCL, SDA) are routed to the
DPI_P14–1 pins using the SRU. Therefore, the timing specifications provided below are valid at the DPI_P14–1 pins.
Table 45. Characteristics of the SDA and SCL Bus Lines for F/S-Mode TWI Bus Devices1
Parameter
fSCL
tHDSTA
tLOW
tHIGH
tSUSTA
tHDDAT
tSUDAT
tSUSTO
tBUF
tSP
1
SCL Clock Frequency
Hold Time (repeated) Start Condition. After This
Period, the First Clock Pulse is Generated.
Low Period of the SCL Clock
High Period of the SCL Clock
Setup Time for a Repeated Start Condition
Data Hold Time for TWI-bus Devices
Data Setup Time
Setup Time for Stop Condition
Bus Free Time Between a Stop and Start Condition
Pulse Width of Spikes Suppressed By the Input Filter
Standard Mode
Min
Max
TBD
TBD
Fast Mode
Min
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
n/a
TBD
n/a
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Max
TBD
Unit
kHz
TBD
μs
μs
μs
μs
μs
ns
μs
μs
ns
All values referred to VIHmin and VILmax levels. For more information, see Electrical Characteristics on page 17.
DPI_P14-1
SDA
tSUDA T
tHDS TA
tLOW
DPI_P14-1
SCL
tHDS TA
S
tBUF
t SP
tH DDA T
tHIGH
tSUS TA
t SUSTO
Sr
Figure 37. Fast and Standard Mode Timing on the TWI Bus
Rev. PrB |
Page 48 of 56 |
November 2008
P
S
Preliminary Technical Data
ADSP-21469/ADSP-21469W
JTAG Test Access Port and Emulation
Table 46. JTAG Test Access Port and Emulation
Parameter
Timing Requirements
tTCK
TCK Period
tSTAP
TDI, TMS Setup Before TCK High
tHTAP
TDI, TMS Hold After TCK High
tSSYS1
System Inputs Setup Before TCK High
1
tHSYS
System Inputs Hold After TCK High
tTRSTW
TRST Pulse Width
Switching Characteristics
tDTDO
TDO Delay from TCK Low
2
tDSYS
System Outputs Delay After TCK Low
1
2
Min
Max
Unit
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
ns
ns
ns
ns
ns
ns
System Inputs = AD15–0, CLKCFG1–0, RESET, BOOTCFG1–0, DAI_Px, and FLAG3–0.
System Outputs = DAI_Px, AD15–0, AMI_RD, AMI_WR, FLAG3–0, CLKOUT, EMU, and ALE.
tTCK
TCK
tSTAP
tHTAP
TMS
TDI
tDTDO
TDO
tSSYS
tHSYS
SYSTEM
INPUTS
tDSYS
SYSTEM
OUTPUTS
Figure 38. IEEE 1149.1 JTAG Test Access Port
Rev. PrB |
Page 49 of 56 |
November 2008
ns
ns
ADSP-21469/ADSP-21469W
Preliminary Technical Data
OUTPUT DRIVE CURRENTS
Figure 39 shows typical I-V characteristics for the output drivers of the ADSP-21469. The curves represent the current drive
capability of the output drivers as a function of output voltage.
INPUT
1.5V
OR
OUTPUT
1.5V
Figure 41. Voltage Reference Levels for AC Measurements
12
CAPACITIVE LOADING
Output delays and holds are based on standard capacitive loads:
30 pF on all pins (see Figure 40). Figure 44 shows graphically
how output delays and holds vary with load capacitance. The
graphs of Figure 42, Figure 43, and Figure 44 may not be linear
outside the ranges shown for Typical Output Delay vs. Load
Capacitance and Typical Output Rise Time (20% to 80%,
V = Min) vs. Load Capacitance.
10
8
TBD
6
4
2
12
0
50
0
100
150
200
250
10
Figure 39. ADSP-21469 Typical Drive at Junction Temperature
8
TBD
TEST CONDITIONS
6
The ac signal specifications (timing parameters) appear in
Table 15 on Page 23 through Table 46 on Page 49. These include
output disable time, output enable time, and capacitive loading.
The timing specifications for the SHARC apply for the voltage
reference levels in Figure 40.
Timing is measured on signals when they cross the 1.5 V level as
described in Figure 41. All delays (in nanoseconds) are measured between the point that the first signal reaches 1.5 V and
the point that the second signal reaches 1.5 V.
4
2
0
0
50
100
150
200
250
Figure 42. Typical Output Rise/Fall Time (20% to 80%,
VDD_EXT = Max)
TESTER PIN ELECTRONICS
50:
VLOAD
T1
12
DUT
OUTPUT
45:
70:
10
ZO = 50:(impedance)
TD = 4.04 r 1.18 ns
50:
4pF
0.5pF
8
2pF
400:
TBD
6
4
NOTES:
THE WORST CASE TRANSMISSION LINE DELAY IS SHOWN AND CAN BE USED
FOR THE OUTPUT TIMING ANALYSIS TO REFELECT THE TRANSMISSION LINE
EFFECT AND MUST BE CONSIDERED. THE TRANSMISSION LINE (TD), IS FOR
LOAD ONLY AND DOES NOT AFFECT THE DATA SHEET TIMING SPECIFICATIONS.
2
ANALOG DEVICES RECOMMENDS USING THE IBIS MODEL TIMING FOR A GIVEN
SYSTEM REQUIREMENT. IF NECESSARY, A SYSTEM MAY INCORPORATE
EXTERNAL DRIVERS TO COMPENSATE FOR ANY TIMING DIFFERENCES.
0
0
Figure 40. Equivalent Device Loading for AC Measurements
(Includes All Fixtures)
Rev. PrB |
50
100
150
200
Figure 43. Typical Output Rise/Fall Time (20% to 80%,
VDD_EXT = Min)
Page 50 of 56 |
November 2008
250
Preliminary Technical Data
ADSP-21469/ADSP-21469W
12
Values of θJB are provided for package comparison and PCB
design considerations. Note that the thermal characteristics values provided in Table 47 are modeled values.
10
Table 47. Thermal Characteristics for 324-Lead PBGA
Parameter
θJA
θJMA
θJMA
θJC
ΨJT
ΨJMT
ΨJMT
8
TBD
6
4
2
0
0
100
50
150
200
250
Figure 44. Typical Output Delay or Hold vs. Load Capacitance
(at Ambient Temperature)
THERMAL CHARACTERISTICS
The ADSP-21469 processor is rated for performance over the
temperature range specified in Operating Conditions on
Page 16.
Table 47 airflow measurements comply with JEDEC standards
JESD51-2 and JESD51-6 and the junction-to-board measurement complies with JESD51-8. Test board design complies with
JEDEC standards JESD51-7 (PBGA). The junction-to-case measurement complies with MIL- STD-883. All measurements use a
2S2P JEDEC test board.
To determine the junction temperature of the device while on
the application PCB, use:
T J = T CASE + ( Ψ JT × P D )
where:
TJ = junction temperature °C
TCASE = case temperature (°C) measured at the top center of the
package
ΨJT = junction-to-top (of package) characterization parameter
is the Typical value from Table 47.
PD = power dissipation
Values of θJA are provided for package comparison and PCB
design considerations. θJA can be used for a first order approximation of TJ by the equation:
T J = T A + ( θ JA × P D )
where:
TA = ambient temperature °C
Values of θJC are provided for package comparison and PCB
design considerations when an external heatsink is required.
Rev. PrB |
Page 51 of 56 |
November 2008
Condition
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Typical
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
ADSP-21469/ADSP-21469W
Preliminary Technical Data
BALL CONFIGURATION - ADSP-21469
Figure 45 shows the ball configuration for the ASDP-21469.
A1 CORNER
INDEX AREA
1
2
3
4
D
R
5
6
7
8
9 10 11 12 13 14 15 16 17 18
A
B
C
D
D
E
D
D
F
D
D
D
R
D
D
D
D
D
D
D
D
G
H
D
A
D
S
J
K
L
M
N
T
P
R
T
U
V
VDDINT
D
VDDEXT
R
VREF
VSS
T
VDD_THD
NC
A
VDD_A
S
VSS_A
I/O SIGNALS
VDD_DDR2
Figure 45. ADSP-21469 Ball Configuration - Pin Out
Rev. PrB |
Page 52 of 56 |
November 2008
Preliminary Technical Data
ADSP-21469/ADSP-21469W
PBGA PINOUT
Table 48 lists the pin assignments of the ADSP-21469 SHARC
processor.
Table 48. 19 mm by 19 mm PBGA Pin Assignment (Alphabetically by Signal)
Signal
AMI_ACK
AMI_ADDR0
AMI_ADDR1
AMI_ADDR2
AMI_ADDR3
AMI_ADDR4
AMI_ADDR5
AMI_ADDR6
AMI_ADDR7
AMI_ADDR8
AMI_ADDR9
AMI_ADDR10
AMI_ADDR11
AMI_ADDR12
AMI_ADDR13
AMI_ADDR14
AMI_ADDR15
AMI_ADDR16
AMI_ADDR17
AMI_ADDR18
AMI_ADDR19
AMI_ADDR20
AMI_ADDR21
AMI_ADDR22
AMI_ADDR23
AMI_DATA0
AMI_DATA1
AMI_DATA2
AMI_DATA3
AMI_DATA4
AMI_DATA5
AMI_DATA6
AMI_DATA7
AMI_MS0
AMI_MS1
AMI_RD
AMI_WR
BOOT_CFG0
BOOT_CFG1
BOOT_CFG2
BR1
BR2
Ball
R10
V16
U16
T16
R16
V15
U15
T15
R15
V14
U14
T14
R14
V13
U13
T13
R13
V12
U12
T12
R12
V11
U11
T11
R11
U18
T18
R18
P18
V17
U17
T17
R17
T10
U10
J4
V10
J2
J3
H3
V8
U8
Signal
BR3
BR4
BR5
BR6
CLK_CFG0
CLK_CFG1
CLKIN
CLKOUT/RESETOUT/RUNRSTIN
DAI_P1
DAI_P2
DAI_P3
DAI_P4
DAI_P5
DAI_P6
DAI_P7
DAI_P8
DAI_P9
DAI_P10
DAI_P11
DAI_P12
DAI_P13
DAI_P14
DAI_P15
DAI_P16
DAI_P17
DAI_P18
DAI_P19
DAI_P20
DDR2_ADDR0
DDR2_ADDR1
DDR2_ADDR2
DDR2_ADDR3
DDR2_ADDR4
DDR2_ADDR5
DDR2_ADDR6
DDR2_ADDR7
DDR2_ADDR8
DDR2_ADDR9
DDR2_ADDR10
DDR2_ADDR11
DDR2_ADDR12
DDR2_ADDR13
Rev. PrB |
Ball
T8
V9
U9
T9
G1
G2
L1
M2
R7
V6
U6
T6
R6
V5
U5
T5
R5
V4
U4
T4
R4
V3
U3
T3
R3
V2
U2
T2
D13
C13
D14
C14
B14
A14
D15
C15
B15
A15
D16
C16
B16
A16
Page 53 of 56 |
Signal
DDR2_ADDR14
DDR2_ADDR15
DDR2_BA0
DDR2_BA1
DDR2_BA2
DDR2_CAS
DDR2_CKE
DDR2_CLK0
DDR2_CLK0
DDR2_CLK1
DDR2_CLK1
DDR2_CS0
DDR2_CS1
DDR2_CS2
DDR2_CS3
DDR2_DATA0
DDR2_DATA1
DDR2_DATA2
DDR2_DATA3
DDR2_DATA4
DDR2_DATA5
DDR2_DATA6
DDR2_DATA7
DDR2_DATA8
DDR2_DATA9
DDR2_DATA10
DDR2_DATA11
DDR2_DATA12
DDR2_DATA13
DDR2_DATA14
DDR2_DATA15
DDR2_DM0
DDR2_DM1
DDR2_DQS0
DDR2_DQS0
DDR2_DQS1
DDR2_DQS1
DDR2_ODT
DDR2_RAS
DDR2_WE
DPI_P1
DPI_P2
November 2008
Ball
B17
A17
C18
C17
B18
C7
E1
B7
A7
B13
A13
C1
D1
C2
D2
B2
A2
B3
A3
B5
A5
B6
A6
B8
A8
B9
A9
A11
B11
A12
B12
C3
C11
A4
B4
A10
B10
B1
C9
C10
R2
U1
Signal
DPI_P3
DPI_P4
DPI_P5
DPI_P6
DPI_P7
DPI_P8
DPI_P9
DPI_P10
DPI_P11
DPI_P12
DPI_P13
DPI_P14
EMU
FLAG0
FLAG1
FLAG2
FLAG3
ID_0
ID_1
ID_2
LACK_0
LACK_1
LCLK_0
LCLK_1
LDAT0_0
LDAT0_1
LDAT0_2
LDAT0_3
LDAT0_4
LDAT0_5
LDAT0_6
LDAT0_7
LDAT1_0
LDAT1_1
LDAT1_2
LDAT1_3
LDAT1_4
LDAT1_5
LDAT1_6
LDAT1_7
NC
NC
Ball
T1
R1
P1
P2
P3
P4
N1
N2
N3
N4
M3
M4
K2
R8
V7
U7
T7
G3
G4
G5
K17
P17
J18
N18
E18
F17
F18
G17
G18
H16
H17
J16
K18
L16
L17
L18
M16
M17
N16
P16
F1
K3
ADSP-21469/ADSP-21469W
Preliminary Technical Data
Table 48. 19 mm by 19 mm PBGA Pin Assignment (Alphabetically by Signal)
Signal
NC
NC
NC
NC
RESET
RPBA
TCK
TDI
TDO
THD_M
THD_P
TMS
TRST
VDD_A
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_DDR2
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
Ball
K4
L2
L3
L4
M1
R9
K15
L15
M15
N12
N11
K16
N15
H1
C5
C12
D3
D6
D8
D18
E2
E4
E7
E10
E11
E17
F3
F5
F15
G14
G16
H15
H18
J5
J15
K14
L5
M14
M18
N5
P6
P8
P10
P12
Signal
VDD_EXT
VDD_EXT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_THD
VSS_A
VSS
VSS
VSS
VSS
VSS
VSS
VSS
Ball
P14
P15
D12
E6
E8
E9
E14
E15
F6
F7
F8
F9
F10
F11
F12
F13
G6
G13
H5
H6
H13
H14
J6
J13
K6
K13
L6
L13
M6
M13
N6
N7
N8
N9
N13
N10
H2
A1
A18
C4
C6
C8
D5
D7
Rev. PrB |
Page 54 of 56 |
Signal
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
November 2008
Ball
D9
D10
D17
E3
E5
E12
E13
E16
F2
F4
F14
F16
G7
G8
G9
G10
G11
G12
G15
H4
H7
H8
H9
H10
H11
H12
J1
J7
J8
J9
J10
J11
J12
J14
J17
K5
K7
K8
K9
K10
K11
K12
L7
L8
Signal
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VREF
VREF
XTAL
Ball
L9
L10
L11
L12
L14
M5
M7
M8
M9
M10
M11
M12
N14
N17
P5
P7
P9
P11
P13
V1
V18
D4
D11
K1
Preliminary Technical Data
ADSP-21469/ADSP-21469W
OUTLINE DIMENSIONS
The ADSP-21469 is available in a 19 mm by 19 mm PBGA leadfree package.
BALL A1
PAD CORNER
19.20
19.00 SQ
18.80
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
17.00
BSC SQ
17.05
16.95 SQ
16.85
1.00
BSC
TOP VIEW
2.40
2.28
2.16
BALL A1
PAD CORNER
18 16 14 12 10 8 6 4 2
17 15 13 11 9 7 5 3 1
BOTTOM VIEW
1.00 REF
DETAIL A
DETAIL A
0.61
NOM
0.50 NOM
0.40 MIN
SEATING
PLANE
0.70
0.60
0.50
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MS-034-BAR-2
Figure 46. 324-Ball Plastic Ball Grid Array [PBGA]
(B-324)
Dimensions shown in millimeters
Rev. PrB |
Page 55 of 56 |
November 2008
1.22
1.17
1.12
0.20
COPLANARITY
ADSP-21469/ADSP-21469W
Preliminary Technical Data
AUTOMOTIVE PRODUCTS
The ADSP-21469 is available for automotive applications with controlled manufacturing. Note that this special model may have specifications that differ from the general release models.
The automotive grade product shown in Table 49 is available for use in automotive applications. Contact your local ADI account representative or authorized ADI product distributor for specific product ordering information. Note that all automotive products are RoHS
compliant.
Table 49. Automotive Products
1
Model
Temperature Range1
On-Chip SRAM Package Description
Package Option
AD21469WBBZ3xx
–40°C to +85°C
5M bit
B-324-2
324-Ball Plastic Ball Grid Array
(PBGA)
Referenced temperature is ambient temperature.
ORDERING GUIDE
Model
ADSP-21469KBZ-ENG2, 3, 4
1
2
3
4
Temperature Range1
0 °C to +70 °C
On-Chip SRAM Package Description
5 Mbit
324-Ball Plastic Ball Grid Array
(PBGA)
Package Option
B-324-2
Referenced temperature is ambient temperature.
Z =Part number subject to change.
Z =RoHS Compliant Part
Available with a wide variety of audio algorithm combinations sold as part of a chipset and bundled with necessary software. For a complete list, visit our website at
www.analog.com/SHARC
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR07809-0-11/08(PrB)
Rev. PrB |
Page 56 of 56 |
November 2008