MAXIM DS1862AB+

Rev 0; 10/08
XFP Laser Control and Digital Diagnostic IC
The DS1862A is a closed-loop laser-driver control IC
with built-in digital diagnostics designed for XFP MSA.
The laser control function incorporates automatic power
control (APC) and allows extinction ratio control though
a temperature-indexed lookup table (LUT). The
DS1862A monitors up to seven analog inputs, including
temperature and monitor diode (MD) current, which are
used to regulate the laser bias current and extinction
ratio. Warning and alarm thresholds can be programmed to generate an interrupt if monitored signals
exceed tolerance. Calibration is also provided internally
using independent gain and offset scaling registers for
each of the monitored analog signals. Settings such as
programmed calibration data are stored in passwordprotected EEPROM memory. Programming is accomplished through an I2C-compatible interface, which can
also be used to access diagnostic functionality.
Applications
Laser Control and Monitoring 10Gbps Optical
Transceiver Modules (XFP)
Laser Control and Monitoring
Features
♦ Implements XFP MSA Requirements for Digital
Diagnostics, Serial ID, and User Memory
♦
♦
♦
I2C-Compatible Serial Interface
Automatic Power Control (APC)
Extinction Ratio Control with Lookup Table
♦ Seven Monitored Channels for Digital Diagnostics
(Five Basic Plus Two Auxiliary)
♦ Internal Calibration of Monitored Channels
(Temp, VCC2/3, Bias Current, Transmitted, and
Received Power)
♦ Programmable Quick-Trip Logic for Turning
Off Laser for Eye Safety
♦ Access to Monitoring and ID Information
♦ Programmable Alarm and Warning Thresholds
♦ Operates from 3.3V or 5V Supply
♦
♦
♦
♦
25-Ball CSBGA, 5mm x 5mm Package
Internal or External Temperature Sensor
-40°C to +100°C Operating Temperature Range
One 8-Bit Buffered DAC
Digital Diagnostics in Optical Transmission
Pin Configuration
Ordering Information
PART
TOP VIEW
1
2
3
4
5
+
TEMP RANGE
PIN-PACKAGE
DS1862AB+
-40°C to +100°C
25 CSBGA
DS1862AB+T&R
-40°C to +100°C
25 CSBGA
+Denotes a lead-free/RoHS-compliant package.
T&R = Tape and reel.
A
P-DOWN/
RST
SC-RX-LOS SC-RX-LOL
THRSET
VCC2
B
RX-LOS
SCL
FETG
RSSI
MODSET
TX-D
SDA
EN1
EN2
BIASSET
INTERRUPT
MOD-NR
AUX1MON
AUX2MON
BMD
MOD-DESEL IBIASMON SC-TX-LOS
VCC3
C
D
Typical Operating Circuit appears at end of data sheet.
E
GND
CSBGA (5mm x 5mm)
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
DS1862A
General Description
DS1862A
XFP Laser Control and Digital Diagnostic IC
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Open-Drain Pin
Relative to Ground.............................................-0.5V to +6.0V
Voltage Range on MOD-DESEL, SDA, SCL,
FETG, THRSET, TX-D, AUX1MON, AUX2MON,
IBIASMON, RSSI, BIASSET, MODSET,
EN1, EN2............................................-0.5V to (VCC3 + 0.5V)*
Voltage Range on SC-RX-LOS,
SC-RX-LOL, RX-LOS, SC-TX-LOS,
MOD-NR, EN1, EN2 ...........................-0.5V to (VCC2 + 0.5V)*
Operating Temperature Range .........................-40°C to +100°C
EEPROM Programming Temperature Range .........0°C to +70°C
Storage Temperature Range .............................-55°C to +125°C
Soldering Temperature...........................Refer to the IPC JEDEC
J-STD-020 Specification.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
(VCC3 = +2.9V to +5.5V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
Main Supply Voltage
VCC3
(Note 1)
Secondary Supply Voltage
VCC2
VCC2 not to exceed VCC3 (Note 2)
MIN
TYP
MAX
UNITS
+5.5
V
+1.6
+3.6
V
VCC3 +
0.5
V
+2.9
High-Level Input Voltage
(SDA, SCL)
VIH
I IH (max) = 10μA
0.7 x
VCC3
Low-Level Input Voltage
(SDA, SCL)
VIL
I IL (max) = -10μA
GND 0.3
0.3 x
VCC3
V
High-Level Input Voltage
(TX-D, MOD-DESEL,
P-DOWN/RST) (Note 3)
VIH
I IH (max) = 10μA
2
VCC3 +
0.3
V
Low-Level Input Voltage
(TX-D, MOD-DESEL,
P-DOWN/RST) (Note 3)
VIL
I IL (max) = -10μA
-0.3
+0.8
V
2
_______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
Supply Current
SYMBOL
ICC3
CONDITIONS
MIN
P-DOWN/RST = 1
High-Level Output Voltage
(FETG)
VOH
I OH (max) = -2mA
VCC3 0.5
Low-Level Output Voltage
(MOD-NR, INTERRUPT, SDA,
FETG)
VOL
I OL (max) = 3mA
0
Resistor (Pullup)
RPU
I/O Capacitance
CI/O
Leakage Current
IL
Leakage Current (SCL, SDA)
IL
Digital Power-On Reset
Analog Power-On Reset
9
TYP
MAX
UNITS
3
5
mA
V
12
0.4
V
15
k
10
pF
-10
+10
μA
-10
+10
μA
POD
1.0
2.2
V
POA
2.0
2.6
V
(Note 4)
DC ELECTRICAL CHARACTERISTICS—INTERFACE SIGNALS TO SIGNAL CONDITIONERS
(VCC2 = +1.6V to +3.6V, VCC3 = +2.9V to +5.5V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
High-Level Input Voltage
(SC-RX-LOS, SC-RX-LOL,
SC-TX-LOS)
VIH
I IH (max) = 100μA
0.7 x
VCC2
VCC2 +
0.1
V
Low-Level Input Voltage
(SC-RX-LOS, SC-RX-LOL,
SC-TX-LOS)
VIL
I IL (max) = -100μA
0
0.3 x
VCC2
V
VOH
I OH (max) = -0.7mA
VCC2 0.2
VOH2
VCC2 = 2.5V to 3.6V, IOH (max) = -2mA
VCC2 0.4
VOH3
VCC2 = 1.6V, I OH (max) = -0.7mA
VCC2 0.2
High-Level Output Voltage
(EN1, EN2)
Low-Level Output Voltage
(EN1, EN2, RX-LOS)
Leakage Current
(SC-RX-LOS, SC-RX-LOL,
SC-TX-LOS, RX-LOS)
V
VOL
I OL (max) = 0.7mA
0.20
VOL2
VCC2 = 2.5V to 3.6V, IOL (max) = 2mA
0.40
IL
-10
+10
V
μA
_______________________________________________________________________________________
3
DS1862A
DC ELECTRICAL CHARACTERISTICS
DS1862A
XFP Laser Control and Digital Diagnostic IC
I2C AC ELECTRICAL CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SCL Clock Frequency
SYMBOL
CONDITIONS
MIN
f SCI
TYP
0
MAX
UNITS
400
kHz
Clock Pulse-Width Low
tLOW
1.3
μs
Clock Pulse-Width High
tHIGH
0.6
μs
Bus Free Time Between STOP
and START Conditions
tBUF
1.3
μs
START Hold Time
tHD:SDA
0.6
μs
START Setup Time
t SU:SDA
0.6
Data In Hold Time
tHD:DAT
0
Data In Setup Time
t SU:DAT
100
μs
0.9
μs
ns
Rise Time of Both SDA and
SCL Signals
tR
(Note 5)
20 +
0.1CB
300
ns
Fall Time of Both SDA and
SCL Signals
tF
(Note 5)
20 +
0.1CB
300
ns
STOP Setup Time
t SU:STO
0.6
μs
MOD-DESEL Setup Time
tHOST_SELECT_SETUP
2
ms
MOD-DESEL Hold Time
tHOST_SELECT_HOLD
10
μs
Aborted Sequence Bus Release
tMOD-DESEL_ABORT
2
Capacitive Load for Each Bus
CB
(Note 5)
EEPROM Write Time
tW
4-byte write (Note 6)
ms
400
pF
16
ms
MAX
UNITS
1.50
±100
1.20
±100
3.0
1000
+5
1
25
+5
12
+0.9
+0.9
+4.0
+4.0
1.2
1.5
mA
nA
mA
nA
V
mV
%
nF
μA
%
μA
ANALOG OUTPUT CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
IBIASSET
IBIASSET (Off-State Current)
IMODSET
IMODSET (Off-State Current)
Voltage on IBIASSET and IMODSET
VTHRSET
VTHRSET Drift
VTHRSET Capacitance Load
APC Calibration Accuracy
IBIASSET
IBIASSET
IMODSET
IMODSET
VMAX
VTHRSET
APC Temp Drift
IBMD DNL
IBMD INL
CONDITIONS
MIN
TYP
0.01
Shutdown
±10
0.01
Shutdown
(Note 7)
IMAX = 100μA
Across temperature (Note 8)
±10
0.7
50
-5
CTHRSET
+25°C
0.200mA to 1.5mA
50μA to 200μA
Sink, SRC_SINK_B = 0
Source, SRC_SINK_B = 1
Sink, SRC_SINK_B = 0
Source, SRC_SINK_B = 1
-5
-0.9
-0.9
-4.0
-4.0
IBMD Voltage Drift
IBMD FS Accuracy
4
_______________________________________________________________________________________
LSB
LSB
%/V
%
XFP Laser Control and Digital Diagnostic IC
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
IMODSET Accuracy
IMODSET DNL
IMODSET INL
IMODSET Temp Drift
IMODSET Voltage Drift
IMODSET FS Accuracy
APC Bandwidth
CONDITIONS
MIN
TYP
MAX
UNITS
%
+25°C, IMODSET = 0.04mA to 1.2mA
-1.5
+1.5
75μA range
150μA range
300μA range
600μA range
1200μA range
75μA range
150μA range
300μA range
600μA range
1200μA range
-0.9
-0.9
-0.9
-0.9
-0.9
-1.5
-1.5
-1.0
-1.0
-1.0
%
%/V
%
kHz
IMD / IAPC = 1 (Note 4)
6
10
+0.9
+0.9
+0.9
+0.9
+0.9
+1.5
+1.5
+1.0
+1.0
+1.0
5
1.2
1.5
30
MIN
TYP
MAX
UNITS
200
ms
LSB
LSB
AC ELECTRICAL CHARACTERISTICS—XFP CONTROLLER
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
Time to Initialize
t INIT
VCC3 within ±5% of nominal
TX-D Assert Time
t OFF
IBIAS and IMOD below 10% of nominal
5
μs
TX-D Deassert Time
t ON
IBIAS and IMOD above 90% of nominal
1
ms
P-DOWN/RST Assert Time
t PDR-ON
100
μs
P-DOWN/RST Deassert Time
t PDR-OFF
IBIAS and IMOD below 10% of nominal
IBIAS and IMOD above 90% of nominal
200
ms
2
ms
MOD-DESEL Deassert Time
INTERRUPT Assert Delay
INTERRUPT Deassert Delay
tMOD-DESEL
30
Time until proper response to I2C
communication
t INIT_ON
Time from fault to interrupt assertion
100
ms
t INIT_OFF
Time from read (clear flags) to interrupt
deassertion
500
μs
0.5
ms
Time from read (clear flags) to MOD-NR
deassertion
0.5
ms
MOD-NR Assert Delay
tMOD-NR-ON Time from fault to MOD-NR assertion
MOD-NR Deassert Delay
tMOD-NR-OFF
RX-LOS Assert Time
tLOS-ON
Time from SC-RX-LOS assertion to
RX-LOS assertion
100
ns
RX-LOS Deassert Time
tLOS-OFF
Time from SC-RX-LOS deassertion to
RX-LOS deassertion
100
ns
P-DOWN/RST Reset Time
tRESET
Time from P-DOWN/RST assertion to
initial reset
Shutdown Time
tFAULT
Time from fault to IBIASSET, IMODSET,
and IBMD below 10%
10
μs
30
μs
_______________________________________________________________________________________
5
DS1862A
ANALOG OUTPUT CHARACTERISTICS (continued)
DS1862A
XFP Laser Control and Digital Diagnostic IC
AC ELECTRICAL CHARACTERISTICS—SOFT* CONTROL AND STATUS
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
SOFT TX-D Assert Time
tOFF_SOFT
SOFT TX-D Deassert Time
t ON_SOFT
tPDR-ON_SOFT IBIAS and IMOD below 10% of nominal
tPDR-OFF_SOFT IBIAS and IMOD above 90% of nominal
SOFT P-DOWN/RST Assert Time
SOFT P-DOWN/RST Deassert Time
Soft MOD-NR Assert Delay
tMOD-NR-ON
CONDITIONS
MIN
TYP
MAX
UNITS
IBIAS and IMOD below 10% of nominal
50
ms
IBIAS and IMOD above 90% of nominal
50
ms
50
ms
200
ms
Time from fault to MOD-NR assertion
50
ms
Time from read (clear flags) to MOD-NR
deassertion
50
ms
Time from SC-RX-LOS assertion to
RX-LOS assertion
50
ms
Time from SC-RX-LOS deassertion to
RX-LOS deassertion
50
ms
500
ms
MAX
UNITS
1.50
mA
_SOFT
Soft MOD-NR Deassert Delay
tMOD-NR-OFF
_SOFT
Soft RX_LOS Assert Time
tLOSON_SOFT
Soft RX_LOS Deassert Time
tLOSOFF_SOFT
Analog Parameter Data Ready
(DATA-NR)
*All SOFT timing specifications are measured from the falling edge of STOP signal during I2C communication.
ANALOG INPUT CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
IBMD Configurable Source or
Sink (+/-)
MIN
TYP
0.05
IBMD Voltage (IBMD - 0μA)
VBMD
IBMD Input Resistance
RBMD
Source mode
Sink mode
2.0
IBMD range 0 to 1.5mA
V
1.2
400
550
700
A/D INPUT VOLTAGE MONITORING (IBIASMON, AUX2MON, AUX1MON, RSSI, BMD)
(VCC3 = +2.9V to +5.5V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Input Resolution
VMON
610
μV
Supply Resolution
VCC2/3
1.6
mV
Input/Supply Accuracy
Update Rate
Input/Supply Offset
0.25
0.5
tFRAME1
ACC
AUX1MON and AUX2MON disabled
48
52
tFRAME2
All channels enabled
64
75
(Note 4)
0
5
LSB
VOS
At factory setting
%FS
ms
Full-Scale Input (IBIASMON and
RSSI)
At factory setting
2.4875
2.5
2.5125
V
Full-Scale Input (AUX1MON,
AUX2MON, VCC2, VCC3)
At factory setting
(Note 9)
6.5208
6.5536
6.5864
V
BMD (Monitor) (TX-P)
FS setting
6
1.5
_______________________________________________________________________________________
mA
XFP Laser Control and Digital Diagnostic IC
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
HIGH BIAS and TX-P Threshold
FS
(Note 10)
VCC2/3 Fault Asserted
Falling Edge Delay
VCC2/3
(Note 11)
QT Temperature Coefficient
MIN
TYP
MAX
UNITS
2.48
2.5
2.52
mA
75
ms
+3
%
0.5
%/V
2.520
mA
-3
QT Voltage Coefficient
QT FS Trim Accuracy (4.2V,
+25°C)
QT Accuracy (Trip) (INL)
2.480
2.500
-2
0
+2
LSB
0.5
%/V
1.5
3
%
TYP
MAX
QT Voltco
QT Tempco
NONVOLATILE MEMORY CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
UNITS
Endurance (Write Cycle)
+70°C
50k
Cycles
Endurance (Write Cycle)
+25°C
200k
Cycles
All voltages are referenced to ground. Current into the IC is positive, and current out of the IC is negative.
Secondary power supply is used to support optional variable power-supply feature of the XFP module. If VCC2 is not used
(i.e., signal conditioners using 3.3V supply), VCC2 should be connected to the VCC3.
Note 3: Input signals (i.e., TX-D, MOD-DESEL, and P-DOWN/RST) have internal pullup resistors.
Note 4: Guaranteed by design. Simulated over process and 50μA < IBMD < 1500μA.
Note 5: CB—total capacitance of one bus line in picofarads.
Note 6: EEPROM write begins after a STOP condition occurs.
Note 7: This is the maximum and minimum voltage on the MODSET and BIASSET pins required to meet accuracy and drift specifications.
Note 8: For VTHRSET, offset may be as much as 10mV.
Note 9: This is the uncalibrated offset provided by the factory; offset adjustment is available on this channel.
Note 10: %FS refers to calibrated FS in case of internal calibration, and uncalibrated FS in the case of external calibration.
Uncalibrated FS is set in the factory and specified in this data sheet as FS (factory). Calibrated FS is set by the user, allowing a change in any monitored channel scale.
Note 11: See the Monitor Channels section for more detail or VCC2 and VCC3 selection.
Note 1:
Note 2:
_______________________________________________________________________________________
7
DS1862A
FAST ALARMS AND VCC FAULT CHARACTERISTICS
XFP Laser Control and Digital Diagnostic IC
DS1862A
Timing Diagrams
RESET-DONE
VCC > VPOA
READ-FLAGS
READ-FLAGS
TX-D
P-DOWN/RST
RESET-DONE
INTERRUPT
tPDR-OFF
IBIASSET
tINIT
tINIT_OFF
tINIT
tINIT_ON
IMODSET
Figure 1. Power-On Initialization with P-DOWN/RST Asserted and TX-D/SOFT TX-D Not Asserted
VCC > VPOA
READ-FLAGS
TX-D
RESET-DONE
P-DOWN/RST
INTERRUPT
IBIASSET
tINIT_ON
tINIT_OFF
tINIT
IMODSET
Figure 2. Power-On Initialization with P-DOWN/RST Not Asserted and TX-D/SOFT TX-D Not Asserted (Normal Operation)
8
_______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
TX-F
TX-D
IBIASSET
tOFF
tON
IMODSET
Figure 3. TX-D Timing During Normal Operation
OCCURRENCE
OF FAULT
FETG
TX-D
IBIASSET
tFAULT
IMODSET
Figure 4. Detection of Safety Fault Condition
_______________________________________________________________________________________
9
DS1862A
Timing Diagrams (continued)
XFP Laser Control and Digital Diagnostic IC
DS1862A
Timing Diagrams (continued)
OCCURRENCE
OF FAULT
P-DOWN/RST
tRESET
FETG
tINIT
IBIASSET
RESET-DONE
IMODSET
Figure 5. Successful Recovery from Transient Safety Fault Condition Using P-DOWN/RST
RESET-DONE
OCCURRENCE
OF FAULT
tFAULT
P-DOWN/RST
tRESET
tFAULT
FETG
(FETG_POL = 1)
IBIASSET
IMODSET
Figure 6. Unsuccessful Recovery from Transient Safety Fault Condition
10
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
OCCURRENCE
OF MONITOR
CHANNEL FAULT
tINIT_ON
INTERRUPT
tINIT_OFF
READ FLAGS
Figure 7. Monitor Channel Fault Timing
______________________________________________________________________________________
11
DS1862A
Timing Diagrams (continued)
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
3.5
3.0
SRC_SINK_B = 0
IBMD = 499.479μA
3.3
3.8
4.3
4.8
4.5
4.0
-1.0
SRC_SINK_B = 1
-2.0
VCC3 = 5.5V, VCC2 = 1.6V
3.0
-15
-40
10
35
IBMD = 499.479μA
60
VCC3 = 5.5V, VCC2 = 1.6V
-2.5
-40
85
-15
10
IBMD = 499.479μA
35
60
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
TEMPERATURE (°C)
IBMD DRIFT vs. SUPPLY VOLTAGE
IMODSET DRIFT vs. TEMPERATURE
INTEGRAL NONLINEARITY
OF QUICK TRIPS
1.0
DS1862A toc04
1.0
0.8
0.6
0.8
0.5
85
0.6
0.4
IMODSET DRIFT (%)
SRC_SINK_B = 0
0.2
0
-0.2
SRC_SINK_B = 1
0
ERROR (LSB)
0.4
-0.4
-0.5
-1.0
0.2
0
-0.2
-0.4
-0.6
-1.5
-0.8
IBMD = 499.479μA
-1.0
2.8
3.6
4.4
-0.6
VCC3 = 5.5V, VCC2 = 1.6V
-2.0
IBMD = 499.479μA
-0.8
-40
5.2
-15
SUPPLY VOLTAGE (V)
10
35
60
85
128
CODE (0–255)
INTEGRAL NONLINEARITY
OF IMODSET
0.15
0.15
0.10
0.05
0.05
ERROR (LSB)
0.10
0
-0.05
-0.10
DS1862A toc08
0.20
DS1862A toc07
0.20
ERROR (LSB)
0
TEMPERATURE (°C)
DIFFERENTIAL NONLINEARITY
OF IMODSET
0
-0.05
-0.10
-0.15
-0.15
VCC3 = 4.2V, VCC2 = 1.6V
-0.20
0
128
CODE (0–255)
12
-0.5
-1.5
SRC_SINK_B = 0
5.3
SRC_SINK_B = 0
DS1862A toc06
2.8
0
5.0
3.5
2.5
2.0
0.5
IBMD DRIFT (%)
4.0
DS1862A toc02
DS1862A toc01
4.5
SRC_SINK_B = 1
5.5
1.0
DS1862A toc05
5.0
SRC_SINK_B = 1
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
5.5
IBMD DRIFT vs. TEMPERATURE
SUPPLY CURRENT vs. TEMPERATURE
6.0
DS1862A toc03
SUPPLY CURRENT vs. SUPPLY VOLTAGE
6.0
IBMD DRIFT (%)
DS1862A
XFP Laser Control and Digital Diagnostic IC
FSR = 75μA
256
VCC3 = 4.2V, VCC2 = 1.6V
-0.20
0
FSR = 75μA
128
CODE (0–255)
______________________________________________________________________________________
256
256
XFP Laser Control and Digital Diagnostic IC
NAME
PIN
FUNCTION
P-DOWN/RST
A1
Power-Down/Reset Input. This multifunction pin is pulled high internally. See the Power-Down/Reset Pin
section for additional information.
SC-RX-LOS
A2
Signal Conditioner Receiver Loss-of-Signal Input. This pin is an active-high input with LVCMOS/LVTTL
voltage levels.
SC-RX-LOL
A3
Signal Conditioner Receiver Loss-of-Lock Input. This pin is an active-high input with LVCMOS/LVTTL
voltage levels.
THRSET
A4
Threshold Set Output. This pin is a programmable voltage source that can be used for Rx signal
conditioner.
1.8V Power-Supply Input
VCC2
A5
RX-LOS
B1
Receiver Loss of Signal. This open-drain output indicates when there is insufficient optical power.
SCL
B2
I2C Serial-Clock Input
FETG
B3
FET Gate Output. This pin can drive an external FET gate associated with safety fault disconnect.
RSSI
B4
Received Power Signal Input
MODSET
B5
Modulation Current Output. This pin is only capable of sinking current.
TX-D
C1
Transmit Disable Input. This pin has an internal pullup resistor.
SDA
C2
I2C Serial-Data Input/Output
EN1
C3
Enable 1 Output. Functional control for signal conditioners.
EN2
C4
Enable 2 Output. Functional control for signal conditioners.
BIASSET
C5
Bias Current Output. This pin is only capable of sinking current.
INTERRUPT
D1
Interrupt. This open-drain output pin indicates a possible operational fault or critical status condition to
the host.
MOD-NR
D2
Indicating Module Operational Fault. Open-drain output. This pin indicates the status of the MOD-NR flag.
AUX1MON
D3
AUX2MON
D4
Aux1 Monitor Input. This pin can be used to measure any voltage quantity.
Aux2 Monitor Input. This pin can be used to measure any voltage quantity or external temperature
BMD
D5
Monitor Diode Current Input. This pin is capable of sourcing or sinking current.
GND
E1
Ground
MOD-DESEL
E2
Module Deselect Input. This pin must be pulled low to enable I2C communication. This pin is pulled high
internally.
IBIASMON
E3
Bias Monitor Input. This pin can be used to monitor the voltage across the laser.
SC-TX-LOS
E4
Signal Conditioner Transmitter Loss of Signal. This pin is an active-high input with LVCMOS/LVTTL
voltage levels.
VCC3
E5
3.3V or 5V Power-Supply Input
______________________________________________________________________________________
13
DS1862A
Pin Description
XFP Laser Control and Digital Diagnostic IC
DS1862A
Block Diagram
VCC2
VCC3
TEMPERATURE
SENSOR
INT
ALARM AND
WARNING
THRESHOLDS
COMPARATORS
INTERRUPT
BMD
OFFSET
RIGHT
SHIFTING
AUX1MON
ADC 13 BIT
MUX
RSSI
GAIN
IBIASMON
AUX2MON
WARNING
FLAGS
ALARM
FLAGS
MASKING BITS
I TO V
ALARM FLAGS
TX-P
VCC3
VCC3
VCC2
VCC2
MEASURED DATA
DS1862A
ADDRESS
R/W
DATA BUS
MISC
CONTROL
SIGNALS
MASKING BITS
ALARM AND
WARNING
THRESHOLDS
WARNING FLAGS
IBMD
INTERRUPT
TABLE
01h
SERIAL ID
DATA
LOWER MEMORY
TABLE-SELECT BYTE
TABLE
02h
EEPROM
TABLE
03h
LUT
TABLE
04h
MODULE
CONFIG
TABLE
05h
THRSET
VCC3
THRSET
RPU
MOD-DESEL
SDA
SCL
I2C
INTERFACE
ADDRESS
R/W
MODSET
DATA BUS
BIAS AND
MODULATION
ENABLE
TEMPERATURE
CONTROLLED
WITH
LUT
BIASSET
IBMD
RX-LOS
AEXT(IBMD)
A
HIGH BIAS QT
VCC3
INT
SC-RX-LOS
TX-F
SC-RX-LOL
VCC2 OR VCC3
SC-TX-LOS
SOFT TX-D
HIGH BIAS ALARM THRESHOLD
EN1
EN2
MOD-NR
LOGIC
HIGH BIAS ALARM
IBIASSET
TX-P
HIGH TX_P ALARM
HIGH TX_P ALARM THRESHOLD
GND
LOW TX_P ALARM THRESHOLD
RPU
TX-D
STARTUP
INITIALIZATION
AND
LASER SAFETY
SHUTDOWN
BLOCK
P-DOWN/RST
FETG
BIAS AND MOD
ENABLE
LOW TX_P ALARM
TX-P
14
RPU
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
The DS1862A’s block diagram is described in detail
within the following sections and memory map/memory
description.
Automatic Power Control (APC)
The DS1862A’s APC is accomplished by closed-loop
adjustment of the bias current (BIASSET) until the feedback current (BMD) from a photodiode matches the
value determined by the APC registers. The relationship between the APC register and IBMD is given by:
IBMD = 5.859μA x APCC<7:0> +
(1.464μA x APCF<1:0>)
where APCC<7:0> is the 8-bit value in Table 04h, Byte
84h that controls the coarse BMD current, and
APCF<1:0> is the 2-bit value that controls the fine BMD
current.
The BMD pin appears as a voltage source in series
with two resistors. The overall equivalent resistance of
the BMD input pin can be closely approximated by the
plot in Figure 8. The voltage that appears on the BMD
pin, assuming no external current load, is 1.2V if BMD
is in sink-current mode (SRC_SINK_B = 0) or 2.0V if
BMD is set to source current (SRC_SINK_B = 1). This
allows the photodiode to be referenced to either VCC3
or GND. When the control loop is at steady state, the
BMD current setting matches the current that is measured by the IBMD voltage across the internal resistance. During a transient period, the DS1862A adjusts
the current drive on the BIASSET pin to bring the loop
into steady state. The DS1862A is designed to support
loop gains of 1/20 to 10.
On power-up, the BMD current ramps up to the previously saved current setting in EEPROM APC registers.
While operating, the DS1862A monitors the BMD current. If it begins to deviate from the desired (set) IBMD
value, the current on the BIASSET pin is again adjusted
to compensate.
Extinction Ratio Control
Lookup Table (LUT)
The DS1862A uses a temperature indexed lookup table
(LUT) to control the extinction ratio. The MODSET pin is
capable of sinking current based on the 8-bit binary value
that is controlling it. The DS1862A also features a userconfigurable current range to increase extinction ratio
resolution. Five current ranges, as described in Table 1,
are available to control the current entering MODSET.
Table 1. Selectable Current Ranges for
MODSET
LUT CURRENT RANGE
TABLE 04h, BYTE 86h<2:0>
CURRENT RANGE
(μA)
000
0 to 75
001
0 to 150
010
0 to 300
011
0 to 600
100
0 to 1200
BMD RESISTANCE vs. BMD SUPPLY CURRENT
600
IBMD
VOLTAGE
584
RBMD (Ω)
565
546
BMD
527
RBMD
508
489
VBMD
470
0
0
0.25
0.50
0.75
1.00
1.25
NOTE: VBMD IS
CONTROLLED BY THE
SRC_SINK_B BIT IN
TABLE 04h.
1.50
IBMD (mA)
Figure 8. Approximate Model of the BMD Input
______________________________________________________________________________________
15
DS1862A
Detailed Description
DS1862A
XFP Laser Control and Digital Diagnostic IC
If the largest current range is selected, the maximum
value of FFh (from LUT) corresponds to a 1200μA sink
current. Regardless of the current range, the MODSET
value always consists of 256 steps, including zero.
IMODSET can be controlled automatically with the temperature-based lookup table, or by three other manual
methods.
Automatic temperature addressed lookup is accomplished by an internal or external temperature sensor
controlling an address pointer. This pointer indexes
through 127 previously loaded 8-bit current values
stored in the LUT. Each one of the 127 temperature
slot locations corresponds to a 2°C increment over
the -40°C to +102°C temperature range. Any temperature above or below these points causes the code in
the first or last temperature slot to be indexed. Both the
internal temperature sensor and an external sensor
connected to AUX2MON are capable of providing a
signal to control the extinction ratio automatically with
an indexed LUT. Table 2 illustrates the relationship
between the temperature and the memory locations in
the LUT.
Automatic and manual control of MODSET is controlled
by two bits, TEN and AEN, that reside in Table 04h,
Byte B2h. By default (from factory) TEN and AEN are
both set, causing complete automatic temperaturebased lookup. If TEN and/or AEN are altered, the
DS1862A is set to one of the manual modes. Table 3
describes manual mode functionality.
Table 3. Truth Table for TEN and AEN Bits
TEN
0
0
AEN
DS1862A LUT FUNCTIONALITY
0
Manual mode that allows users to write a
value directly to the LUT VALUE register
(Table 04h, Byte B1h) to drive MODSET. While
in this mode, the LUT INDEX POINTER register
is not being updated, and no longer drives the
LUT VALUE register.
1
Manual mode that allows users to write a
value directly to the LUT VALUE register
(Table 04h, Byte B1h) to drive MODSET. While
in this mode, the LUT INDEX POINTER register
is still being updated; however, it no longer
drives the LUT VALUE register.
0
Manual mode that allows users to write a
value to the LUT INDEX POINTER register
(Table 04h, Byte B0), then the DS1862A
updates the LUT VALUE register (Table 04h,
Byte B1h) based on the user’s index pointer.
1
Automatic mode (factory default). This mode
automatically indexes the LUT based on
temperature, placing the resulting LUT
address in the LUT INDEX POINTER register
(Table 04h, Byte B0h). Then the MODSET
setting is transferred from that LUT address to
the LUT VALUE register (Table 04h, Byte B1h).
Lastly, the IMODSET is set to the new MODSET
code.
Table 2. Temperature Lookup Table
TEMPERATURE (°C)
16
CORRESPONDING LOOKUP
TABLE ADDRESS
< -40
80h
-40
80h
-38
81h
-36
82h
…
…
+96
C4h
+98
C5h
+100
C6h
+102
C7h
> +102
C7h
1
1
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
The AUX1MON, AUX2MON, and VCC2/3 monitor channels are optional and can be disabled. This feature
allows for shorter frame rate for the essential monitor
channels. Channels that cannot be disabled are internal temperature, BMD, RSSI, and IBIASMON. A table of
full-scale (FS) signal values (using factory internal calibration without right shifting) and the resulting FS code
values for all seven channels is provided in Table 4.
Measuring Temperature—Internal or External
The DS1862A is capable of measuring temperature on
three different monitor channels: internal temperature
sensor, AUX1MON, and AUX2MON. Only the internal
temperature and AUX2MON channels are capable of
indexing the LUT to control the extinction ratio. To use
an external temperature sensor on AUX2MON, the
TEMP_INT/EXT bit in Table 04h, Byte 8Bh, must be set.
While AUX2MON controls the extinction ratio, the internal temperature sensor does not stop running; despite
extinction ratio control by AUX2MON, it is this internal
temperature signal that continues to control the status
of temperature flags. Also, when TEMP_INT/EXT = 1,
the internal temperature clamps at -40°C and
+103.9375°C, and when TEMP_INT/EXT = 0 it clamps at 120°C and +127.984°C. AUX2MON, however, does have
its own flag to indicate an out-of-tolerance condition and
assert the INTERRUPT pin.
Both AUX1MON and AUX2MON can be used to measure temperature as a function of voltage on their
respective pins. They can be enabled by selecting
either 0h or 4h from Table 5. Internal (or external) calibration may be required to transmute the input voltage
to the desired two’s-complement digital code, readable
from the result registers in lower memory, Bytes 6Ah,
6Bh, 6Ch, 6Dh.
Measuring VCC2/3
The DS1862A has the flexibility to internally measure
either VCC2 or VCC3 to monitor supply voltage. VCC2 or
VCC3 is user selectable by the VCC2/3_SEL bit in Table
01h, Byte DCh. To remove VCC2/3 from the round-robin
monitor update scheme, despite having VCC2 or VCC3
selected to be monitored, the Reserve_EN bit in Table
04h, Byte 8Bh can be programmed to a 0. The analog
power-on-reset flag, POA, indicates the status of VCC3
power supply. Even though POA seems to behave similarly to VCC2/3 monitor channel, it is completely separate and has no connection.
RESERVE_E
VCC2/3_SEL
RESULT
0
0
VCC2/3 result not enabled.
0
1
VCC2/3 result not enabled.
1
0
VCC3 is being measured.
1
1
VCC2 is being measured.
Measuring APC and Laser Parameters—BMD,
IBIASMON, RSSI
BMD and BIASSET are used to control and monitor the
laser functionality. Regardless of the set BMD current in
the APC register, the DS1862A measures BMD pin current and uses this value not only to adjust the current
on the BIASSET pin, but also to monitor TX-P as well.
The IBIASMON pin is used to input a voltage signal to
the DS1862A that can be used to monitor the bias current through the laser. This monitor channel does not
drive the HIGH BIAS quick-trip (QT) alarms for safety
Table 4. Monitor Channel FS and LSB Detail
SIGNAL
+FS SIGNAL
+FS (hex)
-FS SIGNAL
-FS (hex)
LSB
127.984°C
7FF8
-120°C
8800
0.0625°C
VCC2/3
6.5528V
FFF8
0V
0000
100μV
IBIASMON
2.4997V
FFF8
0V
0000
38.147μV
RSSI
2.4997V
FFF8
0V
0000
38.147μV
AUX1MON
6.5528V
FFF8
0V
0000
38.147μV
AUX2MON
6.5528V
FFF8
0V
0000
38.147μV
BMD (TX-P)
1.5mA
FFF8
0mA
0000
22.888nA
Temperature
______________________________________________________________________________________
17
DS1862A
Monitor Channels
The DS1862A has seven monitored voltage signals that
are polled in a round-robin multiplexed sequence and
are updated with the frame rate, tFRAME. All channels
are read as 16-bit values, but have 13-bit resolution,
and with the exception of temperature measurements,
all channels are stored as unsigned values. The resulting
16-bit value for all monitored channels, except internal
temperature, is calculated by internally averaging the
analog-to-digital result eight times. The resulting internal
temperature monitor channel is averaged 16 times. See
the Internal Calibration section for a complete description of each channel’s method(s) of internal calibration.
DS1862A
XFP Laser Control and Digital Diagnostic IC
fault functionality, current on the BIASSET pin is monitored by the DS1862A to control the HIGH BIAS quicktrip alarm. Similar to TX-P, the RSSI pin is used to
measure the received power, RX-P.
Measuring Voltage Quantities
using AUX1MON and AUX2MON
AUX1MON and AUX2MON are auxiliary monitor inputs
that may be used to measure additional parameters.
AUX1/2MON feature a user-selectable register that
determines the measured value’s units (i.e., voltage,
current, or temperature). In addition to indicating units,
some of the 4-bit op codes, in Table 5, also place the
part in special modes used for alarms and faults internally. Whichever units’ scale is selected, the DS1862A
is only capable of measuring a positive voltage quanti-
Table 5. AUX1/2MON Functionality
Selection (Unit Selection)
ty, therefore internal or external calibration may be
required to get the binary value to match the measured
quantity. A table of acceptable units and/or their corresponding user-programmable 4-bit op code is provided below.
Alarms and Warning Flags
Based on Monitor Channels
All of the monitor channels feature alarm and warning
flags that are asserted automatically as user-programmed thresholds are internally compared with monitor channel results. Flags may be set, which, if not
masked, will generate an interrupt on the INTERRUPT
pin or generate a safety fault. Whenever V CC2/3 ,
AUX2MON, AUX1MON, RSSI, and internal temperature
go beyond their threshold trip points and the corresponding mask bit is 0, an interrupt is generated on the
INTERRUPT pin and a corresponding warning or alarm
flag is set. Similarly, a safety fault occurs whenever
BMD or BIASSET go beyond threshold trip points.
When this happens, the FETG pin immediately asserts
and BIASSET and MODSET currents are shut down.
VALUE
DESCRIPTION OF AUX1/2MON INTENDED USE
(UNITS OF MEASURE)
0000b
Auxiliary monitoring not implemented
0001b
APD bias voltage (16-bit value is voltage in units
of 10mV)
0010b
Reserved
0011b
TEC current (mA) (16-bit value is current in units
of 0.1mA)
Laser temperature (same encoding as module
temperature)
MSB (BIN)
LSB (BIN)
VOLTAGE (V)
0100b
11000000
00000000
1.875
0101b
Laser wavelength
10000000
10000000
1.255
0110b
+5V supply voltage (encoded as primary voltage
monitor)
0111b
+3.3V supply voltage (encoded as primary
voltage monitor)
1000b
+1.8V supply voltage (encoded as primary
voltage monitor) (VCC2)
1001b
-5.2V supply voltage (encoded as primary voltage
monitor)
1010b
+5V supply current (16-bit value is current in
1101b
+3.3V supply current (16-bit value is current in
0.1mA)
1110b
+1.8V supply current (16-bit value is current in
0.1mA)
1111b
-5.2V supply current (16-bit value is current in
0.1mA)
18
Monitor Channel Conversion Example
Table 6 provides an example of how a 16-bit ADC code
corresponds to a real life measured voltage using the
factory-set calibration on either RSSI or IBIASMON. By
factory default, the LSB is set to 38.147μV.
Table 6. A/D Conversion Example
To calculate VCC2, VCC3, AUX1MON, or AUX2MON,
convert the unsigned 16-bit value to decimal and multiply by 100μV.
To calculate the temperature (internal), treat the two’scomplement value binary number as an unsigned
binary number, then convert it to decimal and divide by
256. If the result is grater than or equal to 128, subtract
256 from the result.
Temperature: high byte = -128°C to +127°C signed;
low byte = 1/256°C.
Table 7. Temperature Bit Weights
S
2-1
26
2-2
25
2-3
24
2-4
23
2-5
22
—
______________________________________________________________________________________
21
—
20
—
XFP Laser Control and Digital Diagnostic IC
MSB (BIN)
LSB (BIN)
TEMPERATURE (°C)
01000000
00000000
+64
01000000
00001000
+64.03215
01011111
00000000
+95
11110110
00000000
-10
11011000
00000000
-40
loaded into the appropriate channels’ Gain register.
This requires forcing two known voltages on to the
monitor input pin. For best results, one of the forced
voltages should be the NULL input and the other
should be 90% of FS. Since the LSB of the least significant bit in the digital reading register is known, the
expected digital results are also known for both the null
and FS value inputs. Figure 9 describes the hysteresis
built into the DS1862A’s LUT functionality.
M6
Internal Calibration
Table 9. Internal Calibration Capabilities
SIGNAL
INTERNAL
SCALING
INTERNAL
OFFSET
RIGHTSHIFTING
Temperature
—
x
—
VCC2/3
x
x
—
IBIASMON
x
x
x
RSSI (RX-P)
x
x
x
AUX1MON
x
x
x
AUX2MON
x
x
x
BMD (TX-P)
x
x
x
To scale a specific input’s gain and offset, the relationship between the analog input and the expected digital
result must be known. The input that would produce a
corresponding digital result of all zeroes is the null
value (normally this input is GND). The input that would
produce a corresponding digital result of all ones is the
full-scale (FS) value minus one LSB. The FS value is
also found by multiplying an all ones digital value by
the weighted LSB. For example, a digital reading is 16
bits long, assume that the LSB is known to be 50μV,
then the FS value would be 216 x 50μV = 3.2768V.
A binary search can be used to find the appropriate
gain value to achieve the desired FS of the converter.
Once the gain value is determined, then it can be
M5
MEMORY LOCATION
The DS1862A has two means for scaling an analog
input to a digital result. The two devices alter the gain
and offset of the signal to be calibrated. All of the
inputs except internal temperature have unique registers for both the gain and the offset that can be found in
Table 04h. See the table below for a complete description of internal calibration capabilities including rightshifting for all monitor channels.
DECREASING
TEMPERATURE
M4
M3
INCREASING
TEMPERATURE
M2
M1
2
4
6
8
TEMPERATURE (°C)
10
12
Figure 9. Lookup Table Hysteresis
With the exception of BMD, which can source or sink
current, all monitored channels are high impedance
and are only capable of directly measuring a voltage. If
other measured quantities are desired, such as light,
frequency, power, current, etc., they must be converted
to a voltage. In this situation the user is not interested in
voltage measurement on the monitored channel, but
the measurement of the desired parameter. Only the
relationship between the indirect measured quantity
(light, frequency, power, current, etc.) to the expected
digital result must be known.
An example of gain scaling using the recommended
binary search procedure is provided with the following
pseudo code.
To help will the computation, two integers need to be
defined: count 1 and count 2. CNT1 = NULL / LSB and
CNT2 = 90%FS / LSB. CLAMP is the largest result that
can be accommodated.
______________________________________________________________________________________
19
DS1862A
Table 8. Temperature Conversion
Examples
DS1862A
XFP Laser Control and Digital Diagnostic IC
/* Assume that the Null input is 0.5V. */
/* In addition, the requirement for LSB is 50μV. */
FS = 65536 * 50e-6;
/* 3.2768 */
CNT1 = 0.5 / 50e-6;
/* 10000 */
CNT2 = 0.90*FS / 50e-6;
/* 58982 */
/* Thus the NULL input of 0.5V and the 90% of FS input
is 2.94912V. */
set the trim-offset-register to zero;
set Right-Shift register to zero (Typically zero.
See the Right-Shifting section);
gain_result = 0h;
CLAMP = FFF8h/2^(Right_Shift_Register);
For n = 15 down to 0
begin
gain_result = gain_result + 2^n;
Force the 90% FS input (2.94912V);
Meas2 = read the digital result from the part;
If Meas2 >= CLAMP then
gain_result = gain_result - 2^n;
Else
Force the NULL input (0.5V);
Meas1 = read the digital result from the part;
if (Meas2 - Meas1) > (CNT2 - CNT1) then
gain_result = gain_result - 2^n;
Right-Shifting A/D Conversion Result
(Scalable Dynamic Ranging)
Right-shifting is a digital method used to regain some
of the lost ADC range of a calibrated system. If rightshifting is enabled, by simply loading a non-zero value
into the appropriate Right-Shifting Register, then the
DS1862A shifts the calibrated result just before it is
stored into the monitor channels’ register. If a system is
calibrated so the maximum expected input results in a
digital output value of less than 7FFFh (50% of FS),
then it is a candidate for using the right-shifting
method.
If the maximum desired digital output is less than
7FFFh, then the calibrated system is using less than 1/2
the ADC’s range. Similarly, if the maximum desired digital output is less than 1FFFh, then the calibrated system is only using 1/8th the ADC’s range. For example, if
an applied maximum analog signal yields a maximum
digital output less than 1FFCh, then only 1/8th of the
ADC’s range is used. Right-shifting improves the resolution of the measured signal as part of internal calibration. Without right-shifting, the 3 MS bits of the ADC will
never be used. In this example, a value of 3 for the
right-shifting maximizes the ADC range and a larger
gain setting must be loaded to achieve optimal conversion. No resolution is lost since this is a 13-bit converter
that is left justified. The value can be right-shifted 3
times without losing any resolution. The following table
describes when the right-shifting method can be effectively used.
end;
Set the gain register to gain_result;
The gain register is now set and the resolution of the
conversion will best match the expected LSB. The next
step is to calibrate the offset of the DS1862A. With the
correct gain value written to the gain register, again
force the NULL input to the monitor pin. Read the digital result from the part (Meas1). The offset value is
equal to negative value of Meas1.
⎡ (− 1)Meas1 ⎤
OFFSET _ REGISTER = ⎢
⎥
4
⎣
⎦
Table 10. Right-Shifting Selection
OUTPUT RANGE USED WITH
ZERO RIGHT-SHIFTS
NUMBER OF RIGHTSHIFTS NEEDED
0h .. FFFFh
0
0h .. 7FFFh
1
0h .. 3FFFh
2
0h .. 1FFFh
3
0h .. 0FFFh
4
The calculated offset is now written to the DS1862A
and the gain and offset-scaling procedure is complete.
20
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
The DS1862A is capable of generating an alarm and/or
warning whenever an analog monitored channel goes
out of a user-defined tolerance. Temperature, bias current (based on IBIASMON), receive power (based on
RSSI), AUX1MON, AUX2MON, and VCC2/3, are moni-
tored channels that generate latched flags. See the figure below for more detail pertaining to AUX1MON and
AUX2MON. Flags are latched into a high state the first
time a monitored channel goes out of the defined operating window and for each monitored signal there is a
Mask bit that can be set to prevent the corresponding
alarm or warning flag from being set. Once a flag is set,
it is cleared by simply reading its memory location.
AUX1/2MON LOGIC
AUX1MON (PIN)
ADC
4-BIT UNIT SELECT
C
THRESHOLD
AUX2MON (PIN)
ADC
C
THRESHOLD
AUX1MON
AUX2MON
*COMPARATOR LOGIC IS
DUPLICATED FOR HIGH
AND LOW ALARMS AND
WARNINGS.
AUX1MON
(VCC2 MODE)
AUX2MON
(VCC2 MODE)
LATCHED-VEE5
LATCHED-VCC2
AUX1MON
(VCC5 MODE)
AUX2MON
(VCC5 MODE)
AUX1MON
(VCC3 MODE)
AUX2MON
(VCC3 MODE)
LATCH
AUX2MON
(VEE5 MODE)
AUX2MON
(TEC MODE)
LATCHED-TECFAULT
LATCH
AUX1MON
(VEE5 MODE)
LATCHEDWAVELENGH-UL
AUX1MON
(TEC MODE)
LATCHED-VCC5
LATCH
AUX2MON
(LASER WL MODE)
LATCH
AUX1MON
(LASER WL MODE)
LATCH
AUX2MON
(APD MODE)
LATCHED-APDSUPPLY-FAULT
LATCH
AUX1MON
(APD MODE)
LATCH
MASK BIT
LATCHED-VCC3
ANY FLAG
INTERRUPT (PIN)
CORRESPONDING MASK
BIT
Figure 10. AUX1/2MON Monitor Logic
______________________________________________________________________________________
21
DS1862A
Warning and Alarm Logic Based on
AUX1/2MON, VCC2/3, Temp, RX-P,
and IBIASMON
Warning and Alarm Logic Based on
Signal Conditioners
The DS1862A also has flags that are set by certain logical
conditions on signal conditioner (SC) pins: SC-RX-LOL,
SC-RX-LOS, SC-TX-LOS. Similarly, for each latched
signal conditioner flag there are also mask bits that are
capable of preventing the alarm or warning flag from
causing an INTERRUPT pin to assert. Again, flags are
cleared automatically whenever their memory address
is read. See Figure 11 for more detail.
Quick-Trip Logic and FETG
Shutdown Functionality
In addition to alarms and warnings, the DS1862A also
has quick-trip (QT) functionality (sometimes referred to
as fast alarms) that is capable of shutting down the
LASER with the FETG pin in conjunction with shutting
down IMODSET and IBIASSET. IBMD and IBIASSET currents are measured and are compared with userdefined trip points to set the quick-trip flags: QT LOW
TX-P, QT HIGH TX-P, and QT HIGH BIAS. These flags
are also capable of being masked to prevent FETG
from being asserted when an out-of-tolerance condition
is detected. FETG is not asserted by setting the TX-D
pin, SOFT TX-D, or P-DOWN/RST pin to a high state,
however, IMODSET, and IBIASSET will shut down. See
Figure 12 for more detail.
The polarity of the FETG pin can also be reversed by
setting the FETG_POL bit. Once a safety fault has
occurred, the FETG pin and all of the attendant flags
SIGNAL CONDITIONER AND MISCELLANEOUS LOGIC
SC-RX-LOL (PIN)
TX-FAULT
VCC2-FAULT
LATCH
LATCHEDRX-LOS
P-DOWN/RST
(PIN)
RX-LOS (PIN)
*OPEN DRAIN
SC-RX-LOL
(PIN)
TIMER
LATCHED-TX-NR
LATCH
LATCHED-RX-NR
LATCHED-TX-FAULT
LATCH
SC-RX-LOS
(PIN)
LATCHED-TX-FAULT
LATCHED-RESET-DONE
LATCH
SC-RX-LOL
(PIN)
LATCH
SC-RX-LOS
(PIN)
SC-TX-LOS
(PIN)
LATCH
HIGH TX-P
LOW TX-P
HIGH BIAS
LATCH
DS1862A
XFP Laser Control and Digital Diagnostic IC
LATCHED
RX-CDR-NL
LATCHEDMOD-NR
MOD-NR (PIN)
*OPEN DRAIN
ANY FLAG
ANY MASK BIT
INTERRUPT (PIN)
Figure 11. Signal Conditioner and Other Logic
22
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
DS1862A
LATCH
SHUTDOWN LOGIC
ADC
QT LOW
TX-P FLAG
THRESHOLD
BMD (PIN)
(TX-P CURRENT)
LOW TX-P MASK
ADC
QT HIGH
TX-P FLAG
THRESHOLD
BIASSET (PIN)
(BIASSET CURRENT)
FETG (PIN)
HIGH TX-P MASK
ADC
QT HIGH
BIAS FLAG
THRESHOLD
SOFT TX-D
P-DOWN/RST (PIN)
TX-D (PIN)
SAFETY FLAG
SOFT P-DOWN/RST
FETG_POL
HIGH BIAS MASK
SHUTDOWN
FLAG
QT LOW TX-P FLAG
QT HIGH TX-P FLAG
QT HIGH BIAS FLAG
FETG_POL
0
DRIVE A P-CHANNEL SWITCH
1
DRIVE A N-CHANNEL SWITCH
LATCH
BMD (PIN)
(TX-P CURRENT)
LATCHED-TX-FAULT
SAFETY FLAG
Figure 12. Safety Fault and Shutdown Logic
can only be reset by pulsing the P-DOWN/RST pin high
for the reset time, tRESET, or by toggling the SOFT PDOWN/RST bit in Byte 6Eh, bit 3. See the PowerDown/Reset Pin section for more details.
Power-Down/Reset Pin
The P-DOWN/RST pin is a multifunction input pin that
resets and/or powers down the DS1862A. Since the pin
is internally pulled up, its normal state is released, which
corresponds to power-down mode. If the P-DOWN/RST
pin is released, or driven high, the DS1862A responds
by shutting down the MODSET and BIASSET currents.
Once the pin is pulled low, operation continues (if not
inhibited by a safety fault). Besides powering down the
DS1862A, a high-going pulse with minimum reset time,
tRESET, can be applied to the P-DOWN/RST pin. This is
necessary to restart the DS1862A, especially if it is in a
safety shutdown condition and needs to be restarted
after the safety condition has been rectified. See the timing diagrams for proper pin timing.
Power-Down Functionality
During power-down mode IBIASSET and IMODSET drop
below 10μA, effectively shutting down the laser. FETG
is not asserted and safety faults do not occur during
this period. During power-down, I2C communication is
still active, but the signal conditioner pins EN1 and EN2
are noncontrollable and automatically change to the
states: EN1 = 1 and EN2 = 0. Other internal flags/signals that are based on the signal conditioner inputs still
reflect the status on the signal conditioner pins during
power-down. For example, RX-LOS still reflects the status of SC-RX-LOS, and MOD-NR still reflects the logical
states for the signal conditioner pins. Similarly, it is possible for FETG to be asserted, even though the BIASSET and MODSET currents are shut down. However,
during power-down and a short period, tPDR-OFF, during power-up, TX-P Low flag is ignored (internally automatically masked out) and does not contribute to
FETG’s logic.
______________________________________________________________________________________
23
DS1862A
XFP Laser Control and Digital Diagnostic IC
During an asserted period of P-DOWN/RST (DS1862A
in power-down), and V CC3 is cycled, the DS1862A
remains in power-down mode upon power-up. While in
power-down mode the INTERRUPT pin does not assert.
Once VCC3 has returned, the reset done flag asserts
after the interrupt assert delay, tINIT_ON.
Reset Functionality
Besides powering down the DS1862A, the PDOWN/RST pin also functions to reset the DS1862A.
After a high-going pulse of time tRESET, several events
occur within the DS1862A. First, MODSET and BIASSET
currents shut down and are then reinstated. Second,
between the rising edge of the reset pulse and the
assertion of the reset-done flag (tINIT), the low TX-P flag
is ignored and does not cause FETG to trip. After time
tINIT, the low TX-P flag becomes functional. Also, at this
time, the reset-done flag is asserted, causing an interrupt to be generated. If there are no faults before tINIT,
then no interrupts are asserted on the INTERRUPT pin.
If VCC3 is powered up while P-DOWN/RST is high, then
the reset-done flag must be cleared twice. The first time
the reset-done flag is generated by VCC3 powering up,
the second time reset-done is generated by a falling
edge on P-DOWN/RST. If VCC3 is continuously powered while P-DOWN/RST is low then only one resetdone flag needs to be cleared. See the timing
diagrams for graphical detail.
Memory Map
Memory Organization
The DS1862A features six separate memory tables that
are internally organized into 4-word rows. The Lower
Memory is addressed from 00h to 7Fh and contains
alarm and warning thresholds, flags, masks, several
control registers, password entry area (PE), and the
24
table select byte. Table 01h primarily contains user
EEPROM as well as several control bytes for various
functions. Table 02h is strictly user EEPROM that is protected by a host password. Table 03h is strictly used
for controlling the extinction ratio with an LUT. Table
04h is a multifunction space that contains internal calibration values for monitored channels, LUT index pointers, and miscellaneous control bytes. Table 05h is
factory programmed and stores SCALE values for use
with suggested external temperature sensors. Also, one
byte in Table 05h controls the THRSET voltage source
and is completely accessible without any password
protection. See the Detailed Register Description section for a more complete detail of each byte’s function,
as well as Table 11 for read/write permissions for each
byte. Many nonvolatile memory locations are actually
SRAM-shadowed EEPROM, which are controlled by the
SEEB bit in Table 04h, Byte B2h.
The DS1862A incorporates SRAM-shadowed EEPROM memory locations for key memory addresses
that may be rewritten many times. By default the shadowed-EEPROM bit, SEEB, is not set and these locations act as ordinary EEPROM. By setting SEEB, these
locations begin to function like SRAM cells, which allow
an infinite number of write cycles without concern of
wearing out the EEPROM. This also eliminates the
requirement for the EEPROM write time, tWR. Because
changes made with SEEB enabled do not affect the
EEPROM, these changes are not retained through
power cycles. The power-up value is the last value written with SEEB disabled. This function can be used to
limit the number of EEPROM writes during calibration or
to change the monitor thresholds periodically during
normal operation helping to reduce the number of times
EEPROM is written. The following information describes
which locations are shadowed-EEPROM.
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
DS1862A
DEC HEX
0
0
I2C SLAVE ADDRESS A0h
00h
LOWER MEMORY
DIGITAL DIAGNOSTIC
FUNCTIONS
PASSWORD ENTRY (PWE)
(4 BYTES)
127
7F
128
80
TABLE SELECT BYTE 7Fh
80h
80h
80h
USER EEPROM DATA
TABLE 05h
TABLE 04h
TABLE 01h
TABLE 00h
XFP MSA
SERIAL ID DATA
80h
80h
TABLE 03h
TABLE 02h
MODULATION DAC
LUT
OPTIONAL SCALE VALUES
AND THRSET CONTROL
CONTROL AND
CONFIGURATION
TABLE
(72 BYTES)
87h
BBh
C7h
220
DC
255
FF
MISC CONTROL BITS
FFh
FFh
Figure 13. General View of DS1862A Memory Organization
Register Map
Table 11. Permission Table
PERMISSION
<0>
READ
WRITE
At least one byte in this row is different than the rest of the bytes, so look at each
byte separately for permissions.
<1>
ALL
ALL
<2>
ALL
MODULE
<3>
ALL
HOST
<4>
MODULE
MODULE
<5>
ALL
FACTORY
<6>
NEVER
HOST
<7>
NEVER
MODULE
______________________________________________________________________________________
25
DS1862A
XFP Laser Control and Digital Diagnostic IC
LOWER MEMORY (00h–7Fh)
WORD 0
WORD 1
ADDRESS
(hex)
BYTE 0/8
BYTE 1/9
00<0,2>
USER EE
Signal Cond*
BYTE 2/A
WORD 2
BYTE 3/B
BYTE 4/C
WORD 3
BYTE 5/D
BYTE 6/E
BYTE 7/F
Temp Alarm Hi
Temp Alarm Lo
Temp Warn Hi
08<2>
Temp Warn Lo
VCC3 Alarm Hi**
VCC3 Alarm Lo**
VCC3 Warn Hi**
10<2>
VCC3 Warn Lo**
Bias Alarm Hi
Bias Alarm Lo
Bias Warn Hi
18<2>
Bias Warn Lo
TX-P Alarm Hi
TX-P Alarm Lo
TX-P Warn Hi
20<2>
TX-P Warn Lo
RX-P Alarm Hi
RX-P Alarm Lo
RX-P Warn Hi
AUX1 Warn Hi
28<2>
RX-P Warn Lo
AUX1 Alarm Hi
AUX1 Alarm Lo
30<2>
AUX1 Warn Lo
AUX2 Alarm Hi
AUX2 Alarm Lo
38<0,2>
AUX2 Warn Lo
40<1>
48<1>
AUX2 Warn Hi
USER EE
USER EE
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
USER SRAM
USER SRAM
USER SRAM
USER SRAM
USER SRAM
USER SRAM
USER SRAM
USER SRAM
USER SRAM
USER SRAM
50<1>
Temp/Res/Bias/ RxP/AUX1/AUX2/ Temp/Res/Bias/
RxP/AUX1/
Tx/Rx Misc
Apd/Tec/
VCC5/3/2/Vee
TxP Alarm
Res Alarm
TxP Warn
AUX2/Res Warn
Flags
Wave/Res Flags Alarm Flags
VCC5/3/2/Vee
Warn Flags
58<1>
Temp/Res/Bias/ RxP/AUX1/AUX2/ Temp/Res/Bias/
RxP/AUX1/
Rx/Rx Misc Apd/Tec/Wave/
TxP Mask
Res Mask
TxP Mask
AUX2/Res Mask
Mask
Res Mask
VCC5/3/2/Vee
Warn Mask
60<1>
Temp Value
68<1>
70<0,1>
78<0,1>
RX-P Value
Reserved
Reserved
Host PW
Host PW
VCC2/3 Value**
Bit7
VCC5/3/2/Vee
Alarm Mask
Bias Value
TX-P Value
AUX1 Value
AUX2 Value
GCS1
Reserved
Reserved
POA
Reserved
PEC_EN
Host PW
PWE (MSB)
PWE (LSB)
EXPANDED BYTES
Bit6*
Bit5
Bit4
Bit3
Bit2
Bit1
GCS0
Host PW
Table Select
Bit0
BYTE
(hex)
BYTE/WORD
NAME
01
Signal Cond<1>*
USER EE
USER EE
USER EE
USER EE
USER EE
EN2 Value
EN1 Value
Lock-T1-221
50
<1>
L-HI-TEMPAL
L-LO-TEMPAL
Reserved
Reserved
L-HI-BIASAL
L-LO-BIASAL
L-HI-TX-PAL
L-LO-TXP-AL
51
<1>
L-HI-RX-PAL
L-LO-RX-PAL
L-HI-AUX1AL
L-LO-AUX1AL
L-HI-AUX2AL
L-LO-AUX2AL
Reserved
Reserved
52
<1>
L-HI-TEMPW
L-LO-TEMPW
Reserved
Reserved
53
<1>
L-HI-RX-P-W
L-LO-RX-PW
L-HI-AUX1W
L-LO-AUX1W
L-HI-AUX2W
L-LO-AUX2W
Reserved
Reserved
54
<1>
L-TX-NR
L-TX-F
L-TX-CDRNL
L-RX-NR
L-RX-LOS
L-RX-CDRNL
L-MOD-NR
L-RESETDONE
55
<1>
L-APD-SUP-F
L-TEC-F
L-WAVE-NL
Reserved
Reserved
Reserved
Reserved
Reserved
<1>
L-HI-VCC5AL
L-LO–VCC5AL
L-HI-VCC3AL
L-LO–VCC3AL
L-HI-VCC2AL
L-LO–VCC2AL
L-HI-VEE5AL
L-LO-VEE5AL
56
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
bit7
bit6
bit5
bit4
bit3
bit1
bit0
L-HI-BIAS-W L-LO-BIAS-W L-HI-TX-P-W L-LO-TX-P-W
*Bit 0 of Address 01h can be written only if bit 0 of Byte DDh in Table 01h is set.
**VCC2/3 are in reserved locations.
26
bit2
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
Bit6
BYTE
(hex)
BYTE/WORD
NAME
57
<1>
L-HI-VCC5-W
58
<1>
HI-TEMP-AL LO-TEMP-AL
MASK
MASK
59
<1>
5A
bit15
bit14
bit13
bit12
L-LO-VCC5-W
Bit5
bit11
bit10
Bit4
bit9
bit8
Bit3
bit7
bit6
Bit2
bit5
bit4
Bit1
bit3
bit2
Bit0
bit1
bit0
L-HI-VCC3-W
L-LO-VCC3-W
L-HI-VCC2-W
L-LO-VCC2-W
L-HI-VEE5-W
L-LO-VEE5-W
Reserved
Reserved
HI-BIAS-AL
MASK
LO-BIAS-AL
MASK
HI-TX-P-AL
MASK
LO-TX-P-AL
MASK
HI-RX-P-AL
MASK
LO-RX-P-AL HI-AUX1-AL LO-AUX1-AL HI-AUX2-AL LO-AUX2-AL
MASK
MASK
MASK
MASK
MASK
Reserved
Reserved
<1>
HI-TEMP-W
MASK
LO-TEMP-W
MASK
Reserved
Reserved
HI-BIAS-W
MASK
LO-BIAS-W
MASK
HI-TX-P-W
MASK
LO-TX-P-W
MASK
5B
<1>
HI-RX-P-W
MASK
LO-RX-P-W
MASK
HI-AUX1-W
MASK
LO-AUX1-W
MASK
HI-AUX2-W
MASK
LO-AUX2-W
MASK
Reserved
Reserved
5C
<1>
RX-LOL
MASK
RX-CDR-NL
MASK
MOD-NR
MASK
RESET-DONE
MASK
5D
<1>
APD-SUP-F
TEC-F MASK
MASK
5E
<1>
HI-VCC5-AL
MASK
5F
<1>
6E
TX-NR MASK TX-F MASK
TX-CDR-NL
RX-NR MASK
MASK
WAVE-NL
MASK
Reserved
Reserved
Reserved
Reserved
Reserved
LO-VCC5-AL
MASK
HI-VCC3-AL
MASK
LO-VCC3-AL
MASK
HI-VCC2-AL
MASK
LO-VCC2-AL
MASK
HI-VEE5-AL
MASK
LO-VEE5-AL
MASK
HI-VCC5-W
MASK
LO-VCC5-W
MASK
HI-VCC3-W
MASK
LO-VCC3-W
MASK
HI-VCC2-W
MASK
LO-VCC2-W
MASK
HI-VEE5-W
MASK
LO-VEE5-W
MASK
<1>
TX-D
SOFT TX-D†
MOD-NR
P-DOWN/RST
RX-LOS
DATA-NR
6F
<1>
TX-NR
TX-F
Reserved
RX-NR
RX-CDR-NL
Reserved
Reserved
Reserved
74
POA <1>
POA
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
77
Host PW<6>
231
230
229
228
227
226
225
224
78
Host PW<6>
223
222
221
220
219
218
217
216
79
Host PW<6>
215
214
213
212
211
210
29
28
7A
Host PW<6>
27
26
25
24
23
22
21
20
7B
PWE<6>
231
230
229
228
227
226
225
224
7C
PWE<6>
223
222
221
220
219
218
217
216
7D
PWE<6>
215
214
213
212
211
210
29
28
7E
PWE<6>
27
26
25
24
23
22
21
20
7F
Table Select<1>
27
26
25
24
23
22
21
20
SOFT PINTERRUPT
DOWN/RST†
†Bit 6 and Bit 3 of Byte 6Eh are masked by Bit 6 and Bit 5 of Byte DDh in Table 01h, respectively.
______________________________________________________________________________________
27
DS1862A
EXPANDED BYTES (CONTINUED)
Bit7
DS1862A
XFP Laser Control and Digital Diagnostic IC
TABLE 01h (SERIAL ID MEMORY)
WORD 0
ADDRESS
(hex)
WORD 1
WORD 2
WORD 3
Byte 0/8
Byte 1/9
Byte 2/A
Byte 3/B
Byte 4/C
Byte 5/D
Byte 6/E
Byte 7/F
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
88<2>
USER EE
USER EE
USER EE
USER EE
USER EE
90<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
98<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
A0<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
A8<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
B0<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
B8<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
C0<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
C8<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
D0<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
AUX1/2 UNIT
SEL
USER EE
80<2>
D8<2>
USER EE
USER EE
USER EE
USER EE
VCC2/3 _SEL
LO MEM 6Eh
EN
E0<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
E8<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
F0<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
F8<2>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
EXPANDED BYTES
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
USER EE
bit15 bit14
USER EE
bit13 bit12
USER EE
bit11 bit10
USER EE
bit9
bit8
USER EE
bit7
bit6
USER EE
bit5
bit4
USER EE
bit3
bit2
USER EE
bit1
bit0
USER EE
VCC2/3 _SEL
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
VCC2/3 _SEL
LO MEM 6Eh EN
Reserved
Enable 6Eh,
bit 6
Enable 6Eh,
bit 3
Reserved
Reserved
Reserved
Reserved
Lock-Bit
AUX1/2 UNIT SEL
AUX1-SEL 23
AUX1-SEL 22
AUX1-SEL 21
AUX1-SEL 20
AUX2-SEL 23
AUX2-SEL 22
BYTE
(hex)
BYTE/WORD
NAME
DC<2>
DD<2>
DE<2>
AUX2-SEL 21 AUX2-SEL 20
Note: Byte DDh<6:5> of Table 01h enables bit 6 and bit 3 of Byte 6Eh in the lower memory.
TABLE 02h (HOST USER MEMORY)
WORD 0
WORD 1
WORD 2
WORD 3
ADDRESS
(hex)
Byte 0/8
Byte 1/9
Byte 2/A
Byte 3/B
Byte 4/C
Byte 5/D
Byte 6/E
Byte 7/F
80–FF<3>
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
USER EE
TABLE 03h (MODSET LOOKUP TABLE)
ADDRESS
(hex)
WORD 0
WORD 1
WORD 2
WORD 3
Byte 0/8
Byte 1/9
Byte 2/A
Byte 3/B
Byte 4/C
Byte 5/D
Byte 6/E
Byte 7/F
80–87<4>
USER EE,
< -40°C
USER EE,
-40°C
USER EE,
-38°C
USER EE,
-36°C
USER EE,
-34°C
USER EE,
-32°C
USER EE,
-30°C
USER EE,
-28°C
88–BF<4>
—
—
—
—
—
—
—
—
C0–C7<4>
USER EE,
+88°C
USER EE,
+90°C
USER EE,
+92°C
USER EE,
+94°C
USER EE,
+96°C
USER EE,
+98°C
USER EE,
+100°C
USER EE,
> +102°C
28
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
WORD 1
WORD 2
WORD 3
Byte 0/8
Byte 1/9
Byte 2/A
Byte 3/B
Byte 4/C
Byte 5/D
Byte 6/E
Byte 7/F
80<4>
Reserved
BIAS SHIFT,
TX-P SHIFT
RX-P SHIFT,
AUX1 SHIFT
AUX2 SHIFT,
Reserved
APC REF
COARSE
APC REF
FINE
LUT RANGE
Control
Register 1
88<4>
QT TX-P HI
QT TX-P LO
QT HIGH BIAS
Control
Register 2
Reserved
Reserved
Reserved
Reserved
90<4>
Reserved
Reserved
MSB
VCC2/3 SCALE
LSB
VCC2/3 SCALE
MSB BIAS
SCALE
LSB BIAS
SCALE
MSB TX-P
SCALE
LSB TX-P
SCALE
98<4>
MSB RX-P
SCALE
LSB RX-P
SCALE
MSB AUX1
SCALE
LSB AUX1
SCALE
MSB AUX2
SCALE
LSB AUX2
SCALE
Reserved
Reserved
A0<4>
MSB TEMP
OFFSET
LSB TEMP
OFFSET
MSB VCC2/3
OFFSET
LSB VCC2/3
OFFSET
MSB BIAS
OFFSET
LSB BIAS
OFFSET
MSB TX-P
OFFSET
LSB TX-P
OFFSET
A8<4>
MSB RX-P
OFFSET
LSB RX-P
OFFSET
MSB AUX1
OFFSET
LSB AUX1
OFFSET
MSB AUX2
OFFSET
LSB AUX2
OFFSET
Reserved
Reserved
B0<4>
LUT INDEX
POINTER
LUT VALUE
LUT_CONF
Reserved
DAC STATUS
Reserved
Reserved
Reserved
B8<7>
MOD_PW_CHNG MOD_PW_CHNG MOD_PW_CHNG MOD_PW_CHNG
EXPANDED BYTES
BYTE
(hex)
BYTE
WORD
NAME
81
<4>
BIAS SHIFT BIAS SHIFT
23
22
BIAS SHIFT
21
BIAS SHIFT
20
TX-P SHIFT
23
TX-P SHIFT
22
TX-P SHIFT
21
TX-P SHIFT
20
82
<4>
RX-P SHIFT
23
RX-P SHIFT
22
RX-P SHIFT
21
RX-P SHIFT
20
AUX1 SHIFT
23
AUX1 SHIFT
22
AUX1 SHIFT
21
AUX1 SHIFT
20
83
<4>
AUX2 SHIFT AUX2 SHIFT
23
22
AUX2 SHIFT
21
AUX2 SHIFT
20
Reserved
Reserved
Reserved
Reserved
84
<4>
APC 27
APC 26
APC 25
APC 24
APC 23
APC 22
85
<4>
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
APC 21
APC 20
86
<4>
Reserved
Reserved
Reserved
Reserved
Reserved
LUT RANGE
22
LUT RANGE
21
LUT RANGE
20
87
<4>
FETG_POL
QT TX-P HI
Mask
QT HIGH BIAS
Mask
QT TX-P LO
Mask
Reserved
Reserved
SRC_SINK_B
Reserved
8B
<4>
Reserved
Reserved
Reserve_EN
TEMP_INT/EXT
Reserved
Reserved
Reserved
Reserved
LUT_
Reserved
CONF<4>
Reserved
Reserved
Reserved
Reserved
SEEB
TEN
AEN
SAFETY
Flag
SHUTDOWN
Flag
Reserved
QT LOW TX-P
Flag
QT HIGH TX-P
Flag
QT HIGH BIAS
Flag
Reserved
Reserved
B2
B4
DAC
STATUS
<4>
Bit7
bit15 bit14
APC 29
Bit6
bit13
bit12
APC 28
Bit5
bit11
bit10
Bit4
bit9
Bit3
bit8
bit7
Bit2
bit6
bit5
Bit1
bit4
bit3
bit2
Bit0
bit1
bit0
B8
Module
PW<7>
231
230
229
228
227
226
225
224
B9
Module
PW<7>
223
222
221
220
219
218
217
216
BA
Module
PW<7>
215
214
213
212
211
210
29
28
BB
Module
PW<7>
27
26
25
24
23
22
21
20
______________________________________________________________________________________
29
DS1862A
TABLE 04h (CONTROL AND CONFIG) (80h–BBh)
WORD 0
ADDRESS
(hex)
DS1862A
XFP Laser Control and Digital Diagnostic IC
TABLE 05h (OPTIONAL OFFSETS AND THRSET)
ADDRESS
(hex)
WORD 0
Byte 0/8
80–87
WORD 1
Byte 1/9
Byte 2/A
DS60 SCALE
WORD 2
Byte 3/B
LM50 SCALE
WORD 3
Byte 4/C
Byte 5/D
Byte 6/E
Byte 7/F
Reserved
Reserved
Reserved
VTHRSET_VALUE <1>
EXPANDED BYTES
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
BYTE
(hex)
BYTE/WORD
NAME
bit15
bit14 bit13
bit12
bit11
bit10
bit9
bit8
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
80
DS60 SCALE <5>
215
214
213
212
211
210
29
28
27
26
25
24
23
22
21
20
82
LM50 SCALE <5>
215
214
213
212
211
210
29
28
27
26
25
24
23
22
21
87
VTHRSET_VALUE
27
26
25
24
23
22
21
20
20
Detailed Register Description
Conventions
Name of Row
• Name of Byte ...................<Read/Write><Volatile><Power-On Value>
• Name of Byte ...................<Read/Write><Nonvolatile><Factory-Default Setting>
• Name of Byte ...................<Read/Write><Shadowed Nonvolatile><Factory-Default Setting>
• Name of Byte ...................<Read/Write><Status><Power-On Value>
Lower Memory
00h
• USER EE ..........................< R-all / W-all ><Shadowed Nonvolatile><00>
01h
• Signal Condition ...............< R-all / W-all ><Volatile><00> Bit 0 can only be written if Table 01h, Byte DDh, bit
<0> is high. Bits <2:1> control EN2 and EN1, respectively.
02h → 39h
• Alarms and Warnings ......< R-all / W-Module ><Shadowed Nonvolatile ><Note*> These registers set the 16bit threshold level for corresponding monitor channels. *Note: High alarm and warnings factory default to FFFFh, and low alarm shut warnings default to 0000h.
3Ah, 3Bh
• USER EE ..........................< R-all / W-all ><Shadowed Nonvolatile><00>
46h → 4Fh
• USER SRAM .....................< R-all / W-all ><Volatile><00>
50h → 57h
• Latched Flags ..................< R-all /clear-all ><Volatile><00> These are latched flags for corresponding signals.
Any flag is cleared by simply reading it.
58h → 5Fh
• Masks ...............................< R-all / W-all ><Volatile><00> These mask bits internally block the signals that
drive the INTERRUPT pin. A low setting causes the corresponding monitor channel
to drive the INTERRUPT pin.
60h → 6Dh
Monitor Values ...........................< R-all / W-all ><Volatile><xxxx> These registers are internally updated with the
monitor channel’s digital result. They can be read as left-justified 16-bit values.
6Eh
GCS1 .........................................< R-all / W-all ><Volatile><xx> These are nonlatched flags, indicating the real-time
digital state of a corresponding signal as well as control bits for particular functions.
30
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
Bit 1: RX-LOS. Indicates optical loss of the signal and is updated within tLOS-ON.
Bit 2: INTERRUPT. Indicates the state of the INTERRUPT pin and is updated within tINIT_ON.
Bit 3: SOFT P-DOWN/RST. R/W bit that places the DS1862A in power-down mode. Toggle to reset. Masked by Bit
5 of Byte DDh in Table 01h.
Bit 4: P-DOWN/RST. Indicates the digital state of the P-DOWN/RST pin and is updated within tPDR-ON.
Bit 5: MOD-NR State. Indicates the state of MOD-NR pin and is updated within tPDR-ON.
Bit 6: SOFT TX-D. R/W bit that disables (shuts down) IBIASSET and IMODSET. Masked by Bit 6 of Byte DDh in Table 01h.
Bit 7: TX-D. Indicates the digital state of the TX-D pin and is updated within tOFF.
6Fh
• 6Fh GCS0 ........................< R-all / W-all ><Status><XX> These are nonlatched flags, indicating the real-time
digital state of a corresponding signal.
Bit 0: Reserved.
Bit 1: Reserved.
Bit 2: Reserved.
Bit 3: RX-CDR-NL not locked. Indicates LOL in Rx path CDR.
Bit 4: RX-NR state. Indicates a NOT READY condition in the Rx path.
Bit 5: Reserved.
Bit 6: TX-F State. Indicates a laser safety fault condition.
Bit 7: TX-NR State. Indicates a NOT READY condition on the Tx path.
74h
• POA ..................................< R-all / W-all ><Volatile><00> A high on bit 7 indicates that VCC3 is below the
power-on analog trip point, POA.
76h
• PEC_EN..............................< R-all / W-all ><Volatile><00> Bit 0 is used to enable PEC. A value of 1 enables PEC.
77h → 7Ah
• Host PW Change .............< R-never / W-Host ><Shadowed Nonvolatile P><00> This is the 32-bit location that
the DS1862A uses to compare with the PWE to grant host password access. A Read
result is always <FFh>.
7Bh → 7Eh
• PWE.....................................< R-never / W-all ><Volatile><00> This is the 32-bit location that is used to enter the host
and module password to gain access to the DS1862A. A Read result is always <FFh>.
7Fh
• Table Select .....................< R-all / W-all ><Volatile><01> This is the 8-bit register that controls which section
of upper memory (table) is being addressed by I2C. A value of 00h and 01h results
in addressing Table 01h. Values above 05h are accepted, but do not correspond to
any physical memory.
Table 01h
80h → DBh
• USER EE ..........................< R-all / W-Module ><Nonvolatile><00>
DCh
• VCC2/3_SEL ......................< R-all / W-Module ><Shadowed Nonvolatile><00> Bit 0 of this register controls
whether VCC2 or VCC3 is internally measured by the VCC2/3 monitor channel. A ‘1’
selects VCC2 to be measured.
______________________________________________________________________________________
31
DS1862A
Bit 0: DATA-NR. Bit is high until DS1862A has achieved power-up. Bit goes low, signaling that monitor channel
data is ready to be read.
DS1862A
XFP Laser Control and Digital Diagnostic IC
DDh
• LO MEM 6Eh EN ..............< R-all / W-Module ><Shadowed Nonvolatile><00> If bit 5 is high, then bit 3 of 6Eh
is not masked. If bit 6 is high, then bit 6 of 6Eh is not masked. Bit 0 is the Lock_Bit. If
set, Lower Memory address 01h, bit 0 is writable.
DEh
• AUX1/2 UNIT SEL ............< R-all / W-Module ><Shadowed Nonvolatile><00> These two 4-bit values define
what is being measured on AUX1MON and AUX2MON. MSB is AUX1MON unit
select and LSB is AUX2MON unit select. See Table 5 for more details.
DFh
• USER EE ..........................< R-all / W-Module ><Shadowed Nonvolatile><00>
E0h → FFh
• USER EE ..........................< R-all / W-Module ><Nonvolatile><00>
Table 02h
80h → FFh
• USER EE ..........................< R-all / W-Host ><Nonvolatile><00>
Table 03h
80h → C7h
• LUT ..................................< R-Module / W-Module ><Nonvolatile><00> These registers control the output current on MODSET as a function of temperature.
Table 04h
80h → B8h
81h
• BIAS SHIFT ......................< R-Module / W-Module ><Shadowed Nonvolatile><0> This 4-bit value in <7:4>
defines how many right-shifts IBIASMON monitor channel receives. The MSB is bit 7.
• TX-P SHIFT .......................< R-Module / W-Module ><Shadowed Nonvolatile><0> This 4-bit value in <3:0>
defines how many right-shifts TX-P (BMD) monitor channel receives. The MSB is bit 3.
82h
• RX-P SHIFT ......................< R-Module / W-Module ><Shadowed Nonvolatile><0> This 4-bit value in <7:4>
defines how many right-shifts RX-P (RSSI) monitor channel receives. The MSB is bit 7.
• AUX1 SHIFT .....................< R-Module / W-Module ><Shadowed Nonvolatile><0> This 4-bit value in <3:0>
defines how many right-shifts AUX1MON monitor channel receives. The MSB is bit 3.
83h
• AUX2 SHIFT .....................< R-Module / W-Module ><Shadowed Nonvolatile><0> This 4-bit value in <7:4>
defines how many right-shifts AUX2MON monitor channel receives. The MSB is bit 7.
84h
• APC REF COARSE ...........< R-Module / W-Module ><Shadowed Nonvolatile><00> This 8-bit value sets the
coarse APC current on BMD.
32
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
• APC REF FINE .................< R-Module / W-Module ><Shadowed Nonvolatile><00> This 2-bit value in <1:0>
sets the fine APC current on BMD. The MSB is bit 1.
86h
• LUT RANGE .....................< R-Module / W-Module ><Shadowed Nonvolatile><00> This 3-bit register in <2:0>
sets the current range on MODSET. The MSB is bit 2.
87h
• Control Register 1 ............< R-Module / W-Module ><Shadowed Nonvolatile><00>
Bit 0: Reserved.
Bit 1: SRC_SINK_B. If set, then BMD sources current; otherwise, BMD sinks current.
Bit 2: Reserved.
Bit 3: Reserved.
Bit 4: QT TX-P LO Mask. If set, then TX-P low does not have the ability to cause a safety fault.
Bit 5: QT HIGH BIAS Mask. If set, then HIGH BIAS does not have the ability to cause a safety fault.
Bit 6: QT TX-P HI Mask. If set, then TX-P high does not have the ability to cause a safety fault.
Bit 7: FETG_POL. If set, then FETG asserts with a high logic level; otherwise, it asserts with a low logic level.
88h
• QT TX-P HI .......................< R-Module / W-Module ><Shadowed Nonvolatile><FF> This is the TX-P quick-trip
threshold setting that is used as a comparison to generate a TX-P high safety fault.
89h
• QT TX-P LO ......................< R-Module / W-Module ><Shadowed Nonvolatile><00> This is the TX-P quick-trip
threshold setting that is used as a comparison to generate a TX-P low safety fault.
8Ah
• QT HIGH BIAS .................< R-Module / W-Module ><Shadowed Nonvolatile><FF> This is the TX-P quick-trip
threshold setting that is used as a comparison to generate a HIGH BIAS safety fault.
8Bh
• Control Register 2 ............< R-Module / W-Module ><Shadowed Nonvolatile><00>
Bit 0: Reserved.
Bit 1: Reserved.
Bit 2: Reserved.
Bit 3: Reserved.
Bit 4: TEMP_INT/EXT. If set, then the LUT INDEX POINTER register is controlled by AUX2MON. Otherwise, the
internal temperature sensor controls the LUT.
Bit 5: Reserve_EN. If set, then VCC2/3 is actively updated in the monitor loop.
Bit 6: Reserved.
Bit 7: Reserved.
______________________________________________________________________________________
33
DS1862A
85h
DS1862A
XFP Laser Control and Digital Diagnostic IC
92h
VCC2/3 SCALE ...........................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the scale value for the VCC2/3 monitor channel.
94h
• BIAS SCALE .....................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the scale value for the BIAS monitor channel.
96h
• TX-P SCALE .....................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the scale value for the TX-P (BMD) monitor channel.
98h
• RX-P SCALE .....................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the scale value for the RX-P (RSSI) monitor channel.
9Ah
• AUX1 SCALE ...................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the scale value for the AUX1MON monitor channel.
9Ch
• AUX2 SCALE ...................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the scale value for the AUX2MON monitor channel.
A0h
• TEMP OFFSET .................< R-Module / W-Module ><Shadowed Nonvolatile><Factory Trimmed> This 16-bit
register controls the offset value for the internal temperature monitor channel.
A2h
• VCC2/3 OFFSET ................< R-Module / W-Module ><Shadowed Nonvolatile><0000> This 16-bit register controls the offset value for the VCC2/3 monitor channel.
A4h
• BIAS OFFSET...................< R-Module / W-Module ><Shadowed Nonvolatile><0000> This 16-bit register controls the offset value for the BIAS monitor channel.
A6h
• TX-P OFFSET ...................< R-Module / W-Module ><Shadowed Nonvolatile><0000> This 16-bit register controls the offset value for the TX-P (BMD) monitor channel.
A8h
• RX-P OFFSET ...................< R-Module / W-Module ><Shadowed Nonvolatile><0000> This 16-bit register controls the offset value for the RX-P (RSSI) monitor channel.
AAh
• AUX1 OFFSET ..................< R-Module / W-Module ><Shadowed Nonvolatile><0000> This 16-bit register controls the offset value for the AUX1MON monitor channel.
ACh
• AUX2 OFFSET ..................< R-Module / W-Module ><Shadowed Nonvolatile><0000> This 16-bit register controls the offset value for the AUX2MON monitor channel.
B0h
• LUT INDEX POINTER .......< R-Module / W-Module ><Volatile><xx> This register controls the index pointer
value for the LUT. It is automatically updated (in normal operating mode) and can
be read or overwritten using the TEN and AEN bits.
34
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
Bit 2: SEEB. A high on SEEB disables EEPROM writes of Shadowed EEPROM locations.
Bit 3: Reserved.
Bit 4: Reserved.
Bit 5: Reserved.
Bit 6: Reserved.
Bit 7: Reserved.
B4h
• DAC STATUS ...................< R-Module / W-Module ><Status><xx0xxx00b>
Bit 0: Reserved.
Bit 1: Reserved.
Bit 2: QT HIGH BIAS Flag. This flag indicates that the current entering BIASSET is above the threshold.
Bit 3: QT HIGH TX-P Flag. This flag indicates that TX-P is above the threshold.
Bit 4: QT LOW TX-P Flag. This flag indicates that TX-P is below the threshold.
Bit 5: Reserved.
Bit 6: SHUTDOWN Flag. A high indicates that the DS1862A is in shutdown mode and that FETG is asserted.
Bit 7: SAFETY Flag. A high indicates that a safety fault (quick trip) has occurred.
B8h
• MOD_PW_CHNG .............< R-never / W-Module ><Shadowed Nonvolatile><00h> This is the 32-bit location
that the DS1862A uses to compare with the PWE to grant module password access.
A Read result is always <FFh>.
Table 05h
80h
• DS60 SCALE ....................< R-all / W-Factory ><Nonvolatile><Factory Trimmed> This unique 16-bit value sets
the SCALE register for use with a DS60 temperature sensor on AUX2MON.
82h
• LM50 SCALE ....................< R-all / W-Factory ><Nonvolatile><Factory Trimmed> This unique 16-bit value sets
the SCALE register for use with a LM50 temperature sensor on AUX2MON.
87h
• VTHRSET_VALUE................< R-all / W-all ><Shadowed Nonvolatile><80> This 8-bit value sets the voltage on
the signal conditioner voltage source, THRSET.
______________________________________________________________________________________
35
DS1862A
B1h
• LUT VALUE ......................< R-Module / W-Module ><Shadowed Nonvolatile><00> This register contains the
fetched LUT value that drives the MODSET current. It can be read or overwritten to
directly control the MODSET current (manual mode).
B2h
• LUT_CONF .......................< R-Module / W-Module ><Shadowed Nonvolatile><03>
Bit 0: AEN. A high on AEN enables data placed in the LUT VALUE register to drive MODSET.
Bit 1: TEN. A high on TEN enables the LUT index pointer to fetch data from the LUT.
DS1862A
XFP Laser Control and Digital Diagnostic IC
Security/Password Protection
The DS1862A features two separate and independent
32-bit passwords for important memory locations. The
host password and the module password allow their
own allocated memory locations to be locked to prevent write and/or read access. To enhance the security
of the DS1862A, the password entry and setting bytes
can never be read.
To gain access to host-protected or module-protected
memory locations, the correct 32-bit value must be
entered into the password entry bytes (PWE) in either a
single 4-byte write, or 4 single-byte writes. To reprogram
either password, simply enter the appropriate current
password to gain memory access, write the new Host or
module PW with one 4-byte write, and finally re-enter the
new password into the PWE to regain memory access.
Power-Up Sequence
The DS1862A does require a particular power-up
sequence to ensure proper functionality. VCC3 should
always be applied first or at the same time as VCC2. If
this power-up sequence is not followed, then current can
be sourced out of VCC2 as if it was connected to VCC3
with a resistor internal to the DS1862A. If VCC2 is not
used then it should be externally connected to VCC3.
Signal Conditioners—
EN1 and EN2 and THRSET
Signal Conditioners—EN1 and EN2
The EN1 and EN2 output pins are controlled by the bits
at address 01h, bits 2 and 1. The logic state of the pins
is directly analogous to the logical state of the register.
EN1 and EN2 automatically change to a high and low
state, respectively, during power-down mode as
described in the Power-Down Functionality section.
Signal Conditioners—THRSET
A programmable voltage source, THRSET, is also provided for use with signal conditioners. This source is
programmable from 0 to 1V in 256 increments.
I2C and Packet Error
Checking (PEC) Information
The DS1862A supports I2C data transfers as well as
data transfers with PEC. The slave address is unalterable and is set to A0h. The DS1862A, however, does
have an additional dedicated pin, MOD-DESEL, which
acts as an active-low chip select to enable communication. See the I2C Serial Interface and the I2C Operation
Using Packet Error Checking sections for details.
36
Precision SCALE Register
Settings for AUX2MON
The DS1862A features a factory-trimmed SCALE value
for use with DS60 or LM50 temperature sensors. If
external temperature measurement on AUX2MON is
used with one of these two sensors, the 16-bit SCALE
value can be read from Table 05h and written into the
SCALE register in Table 04h, Byte 9Ch and 9Dh. This
option allows for the most precise setting for SCALE
without requiring additional trimming. Since the SCALE
register value is precisely trimmed at the factory, the
OFFSET register will always be a nonunique value and
can simply be written into the OFFSET register. For the
DS60, the value of EF0Ah in OFFSET completes the
internal calibration. For the LM50, the value of F380h in
OFFSET completes the internal calibration.
I2C Serial Interface
I2C Definitions
The following terminology is commonly used to describe
I2C data transfers.
Master device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses and START and STOP conditions.
Slave devices: Slave devices send and receive data at
the master’s request.
Bus idle or not busy: Time between STOP and START
conditions when both SDA and SCL are inactive and in
their logic-high states.
START condition: A START condition is generated by
the master to initiate a new data transfer with a slave.
Transitioning SDA from high to low while SCL remains
high generates a START condition. See Figure 14 for
applicable timing.
STOP condition: A STOP condition is generated by the
master to end a data transfer with a slave. Transitioning
SDA from low to high while SCL remains high generates
a STOP condition. See Figure 14 for applicable timing.
REPEATED START condition: The master can use a
REPEATED START condition at the end of one data
transfer to indicate that it will immediately initiate a new
data transfer following the current one. REPEATED
STARTs are commonly used during read operations to
identify a specific memory address to begin a data transfer. A REPEATED START condition is issued identically
to a normal START condition. See Figure 14 for applicable timing.
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
ter are done according to the bit write definition and the
acknowledgement is read using the bit read definition.
Byte read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the bit
read definition, and the master transmits an ACK using
the bit write definition to receive additional data bytes.
The master must NACK the last byte read to terminate
communication so the slave returns control of SDA to
the master.
Slave address byte: Each slave on the I 2 C bus
responds to a slave addressing byte sent immediately
following a START condition. The slave address byte
contains the slave address in the most significant 7 bits
and the R/W bit in the least significant bit.
The DS1862A’s slave address is 1010000Xb. The
MOD-DESEL pin is used as a chip select, and allows
the device to respond or ignore I2C communication that
has A0h as the device address. By writing the correct
slave address with R/W = 0, the master indicates it will
write data to the slave. If R/W = 1, the master will read
data from the slave. If an incorrect slave address is
written, the DS1862A assumes the master is communicating with another I2C device and ignores the communications until the next START condition is sent.
Memory address: During an I2C write operation, the
master must transmit a memory address to identify the
memory location where the slave is to store the data.
SDA
tBUF
tHD:STA
tLOW
tR
tSP
tF
SCL
tHD:STA
STOP
tSU:STA
tHIGH
tSU:DAT
START
REPEATED
START
tSU:STO
tHD:DAT
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
Figure 14. I2C Timing Diagram
______________________________________________________________________________________
37
DS1862A
Bit write: Transitions of SDA must occur during the low
state of SCL. The data on SDA must remain valid and
unchanged during the entire high pulse of SCL plus the
setup and hold time requirements (Figure 14). Data is
shifted into the device during the rising edge of the SCL.
Bit read: At the end of a write operation, the master
must release the SDA bus line for the proper amount of
setup time (Figure 14) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master generates all SCL clock pulses including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK): An Acknowledgement (ACK) or Not Acknowledge (NACK) is always
the 9th bit transmitted during a byte transfer. The device
receiving data (the master during a read or the slave during a write operation) performs an ACK by transmitting a
zero during the 9th bit. A device performs a NACK by
transmitting a one during the 9th bit. Timing (Figure 14)
for the ACK and NACK is identical to all other bit writes.
An ACK is the acknowledgment that the device is properly receiving data. A NACK is used to terminate a read
sequence or as an indication that the device is not
receiving data.
Byte write: A byte write consists of 8 bits of information
transferred from the master to the slave (most significant bit first) plus a 1-bit acknowledgement from the
slave to the master. The 8 bits transmitted by the mas-
DS1862A
XFP Laser Control and Digital Diagnostic IC
The memory address is always the second byte transmitted during a write operation following the slave
address byte.
I2C Communication
Writing a single byte to a slave: The master must
generate a START condition, write the slave address
byte (R/W = 0), write the memory address, write the
byte of data, and generate a STOP condition.
Remember the master must read the slave’s acknowledgement during all byte write operations.
Writing multiple bytes to a slave: To write multiple
bytes to a slave, the master generates a START condition, writes the slave address byte (R/W = 0), writes the
memory address, writes up to 4 data bytes, and generates a STOP condition.
The DS1862A is capable of writing 1 to 4 bytes (referred
to as one row or page) with a single write transaction.
This is internally controlled by an address counter that
allows data to be written to consecutive addresses without transmitting a memory address before each data
byte is sent. The address counter limits the write to one
row of the memory map. Attempts to write to additional
memory rows without sending a STOP condition
between rows results in the address counter wrapping
around to the beginning address of the present row.
To prevent address wrapping from occurring, the master must send a STOP condition at the end of the row,
and then wait for the bus free or EEPROM write time to
elapse. Then the master can generate a new START
condition, and write the slave address byte (R/W = 0)
and the first memory address of the next memory row
before continuing to write data.
Acknowledge polling: Any time EEPROM is written,
the DS1862A requires the EEPROM write time (tW) after
the STOP condition to write the contents of the row to
EEPROM. During the EEPROM write time, the DS1862A
does not acknowledge its slave address because it is
busy. It is possible to take advantage of this phenomenon by repeatedly addressing the DS1862A, which
allows the next row to be written as soon as the
DS1862A is ready to receive the data. The alternative to
acknowledge polling is to wait for the maximum period
of tW to elapse before attempting to write again to the
DS1862A.
EEPROM write cycles: When EEPROM writes occur,
the DS1862A writes the whole EEPROM memory 4-byte
row even if only a single byte on the row was modified.
38
Writes that do not modify all 4 bytes on the row are
allowed and do not corrupt the remaining bytes of
memory on the same row. Because the whole row is
written, bytes on the row that were not modified during
the transaction are still subject to a write cycle. This
can result in a whole row being worn out over time by
writing a single byte repeatedly. Writing a row one byte
at a time wears out the EEPROM four times faster than
writing the entire row at once. The DS1862A’s EEPROM
write cycles are specified in the Nonvolatile Memory
Characteristics table.
Reading a single byte from a slave: Unlike the write
operation that uses the memory address byte to define
where the data is to be written, the read operation
occurs at the present value of the memory address
counter. To read a single byte from the slave at the
location currently in the address counter, the master
generates a START condition, writes the slave address
byte with R/W = 1, reads the data byte with a NACK to
indicate the end of the transfer, and generates a STOP
condition.
Manipulating the address counter for reads: A
dummy write cycle can be used to force the address
counter to a particular value. To do this the master generates a START condition, writes the slave address
byte (R/W = 0), writes the memory address where it
desires to read, generates a REPEATED START condition, writes the slave address byte (R/W = 1), reads
data with ACK or NACK as applicable, and generates a
STOP condition.
See Figure 15 for a read example using the REPEATED
START condition to specify the starting memory location.
Reading multiple bytes from a slave: The read operation can be used to read multiple bytes with a single
transfer. When reading bytes from the slave, the master
simply ACKs the data byte if it desires to read another
byte before terminating the transaction. After the master reads the last byte it NACKs to indicate the end of
the transfer and generates a STOP condition. This can
be done with or without modifying the address
counter’s location before the read cycle. If the address
counter reaches the last physical address, the internal
index pointer loops back to the first memory location in
a given memory table. For example, if address FFh in
Table 02h is read, the next byte of data to be returned
to the master is address 80h in Table 02h, not 00h in
lower memory.
______________________________________________________________________________________
XFP Laser Control and Digital Diagnostic IC
DS1862A
COMMUNICATIONS KEY
S
START
A
ACK
WHITE BOXES INDICATE THE MASTER IS
CONTROLLING SDA
P
STOP
N
NOT
ACK
SHADED BOXES INDICATE THE SLAVE IS
CONTROLLING SDA
SR
REPEATED
START
X
X
X
0
0
0
X
X
X
X
X
NOTE:
ALL BYTES ARE SENT MOST SIGNIFICANT BIT FIRST.
THE FIRST BYTE SENT AFTER A START CONDITION IS
ALWAYS THE SLAVE ADDRESS FOLLOWED BY THE
READ/WRITE BIT.
8-BIT ADDRESS OR DATA
WRITE A SINGLE BYTE
S
1 0
1
0 0
A
MEMORY ADDRESS
A
DATA
A
A
DATA
A
P
WRITE UP TO A 4-BYTE PAGE WITH A SINGLE TRANSACTION
S
1 0
1
0 0
0
0
0
A
MEMORY ADDRESS
A
DATA
P
READ A SINGLE BYTE WITH A DUMMY WRITE CYCLE TO SET THE ADDRESS COUNTER
S
1 0
1
0 0
0
0
0
MEMORY ADDRESS
A
A
SR
1 0
1
0 0
0
0
0
A
DATA
N
1 0
1
0 0
0
0
0
A
DATA
A
P
READ MULTIPLE BYTES WITH A DUMMY WRITE CYCLE TO SET THE ADDRESS COUNTER
S
1 0
1
0 0
0
DATA
0
0
A
MEMORY ADDRESS
A
A
DATA
SR
A
DATA
N
P
Figure 15. I2C Communications Examples
I2C Operation Using
Packet Error Checking
Read Operation with
Packet Error Checking
Packet error checking during reads is supported by the
DS1862A. Information is transferred form the DS1862A
in much the same way as conventional I2C protocol,
however, an extra CRC field is added and checked.
The master still begins by sending the device address
(A0h for DS1862A), then the index pointer to the memory address of interest. The next byte transferred, however, is the value of the intended number of bytes to be
read. The calculation of the CRC-8 includes and
requires the explicit starting memory address to be
included as the second transferred byte (dummy write
byte). Next, the slave transfers the data back as the
master acknowledges. Only 1 to 128 bytes can be
sequentially read during one transmission while using
PEC. After the master reads the intended number of
bytes, the CRC-8 value is transmitted by the DS1862A.
The master ends the communication with a NACK and
a STOP. See Figure 16 for a graphical representation.
The CRC-8 is calculated starting with the MSB of the
memory address pointer, number of bytes to read, and
the read data. The master can then verify the CRC-8
value and reject the read data if the CRC-8 value does
not correspond to the received CRC value. The CRC-8
must be calculated by using the following polynomial
for both reads and writes:
C(x) = X8 +X2 + X + 1
Write Operation with
Packet Error Checking
Packet error checking during writes is also supported
by the DS1862A. Information is written to the DS1862A
in much the same way as conventional I2C protocol,
however, an extra CRC field is added and checked.
The master still begins by sending the device address,
then the index pointer to the memory address of interest. The next byte, however, is the value of the intended
number of bytes to be written. The calculation of the
______________________________________________________________________________________
39
DS1862A
XFP Laser Control and Digital Diagnostic IC
CRC-8 includes and requires the explicit starting memory address to be included as the second transferred
byte. Next, the master transfers the data as the
DS1862A acknowledges. Only 4 bytes can be sequentially written during one transmission while using PEC.
After the master writes the intended number of bytes,
the CRC-8 value should be transmitted. Following the
CRC-8 byte, the master should transmit the CAB byte
(CRC Add-on Byte). At this point, the DS1862A sends
an ACK if the CRC-8 matches its internal calculated
value or a NACK if not. Finally, the master should end
the communication and send a STOP. See Figure 16 for
a graphical representation. The CRC-8 is calculated
starting with the MSB of the memory address pointer,
number of bytes to be written, and the written data. The
master can then poll the last ACK or NACK for successful transfer of written data.
For more information on I2C PEC communications, refer
to the XFP and/or SMBus 2.0 standard.
Applications Information
Calibrating APC and Extinction Ratio
Before calibrating, the APC register should be set to a
low value to ensure the laser’s maximum power level is
not exceeded before the power level is calibrated.
Additionally, the ER should be set to a minimum value
to ensure that a data test pattern does not cause the
laser to shut off. Once the APC and ER registers are at
minimal values, enable a data pattern and calibrate the
average power level.
Calibrating the Average Power Level
While sending data through the laser diode, increase
the value in the APC register until the light output
matches the desired average power level. The average
power level is the arithmetic average of the ‘1’ and ‘0’
power levels.
COMMUNICATIONS KEY
S
START
A
ACK
WHITE BOXES INDICATE THE MASTER IS
CONTROLLING SDA
P
STOP
N
NOT
ACK
SHADED BOXES INDICATE THE SLAVE IS
CONTROLLING SDA
SR
REPEATED
START
X
X
X
X
X
X
X
X
NOTE:
ALL BYTES ARE SENT MOST SIGNIFICANT BIT FIRST.
THE FIRST BYTE SENT AFTER A START CONDITION IS
ALWAYS THE SLAVE ADDRESS FOLLOWED BY THE
READ/WRITE BIT.
8-BIT ADDRESS OR DATA
WRITE UP TO A 4-BYTE PAGE WITH A SINGLE TRANSACTION USING PEC
S
1 0
1
0 0
0
0
0
DATA
A
MEMORY ADDRESS
A
NUMBER OF BYTES
A
DATA
A
A
DATA
A
DATA
A
CRC-8 VALUE
A
NUMBER OF BYTES
A
P
A (IF CRC-8 IS CORRECT)
DATA
READ 1–128 BYTES WITH A DUMMY WRITE CYCLE TO SET THE ADDRESS COUNTER
S
1 0
1
0 0
0
DATA
0
0
MEMORY ADDRESS
A
A
A
DATA
A
SR
CRC-8 VALUE
1 0
1
0 0
N
P
0
Figure 16. I2C PEC Communications Examples
40
______________________________________________________________________________________
0
0
A
XFP Laser Control and Digital Diagnostic IC
SDA and SCL Pullup Resistors
SDA is an open-collector bidirectional data pin on the
DS1862A that requires a pullup resistor to realize high
logic levels. Either an open-collector output with a pullup
resistor or a push-pull output driver can be utilized for
the SCL input. Pullup resistor values should be chosen
to ensure that the rise and fall times listed in the I2C AC
Electrical Characteristics are within specification.
Typical Operating Circuit
1.8V
3.3V
0.1μF
0.1μF
HOST
3.3V
3.3V
10nF
1kΩ
4.7kΩ
4.7kΩ
VCC2
VCC3
FETG
SDA
OUT
IBIASMON
SCL
BIASSET
TX-DISABLE
3.3V
3.3V
MONITOR
TX-D
TX-DISABLE
DS1862A
3.3V
MODSET
BIASSET
DISABLE
MODSET
MAX3975
LASER
DRIVER
MOD-DESEL
10kΩ
10kΩ
10kΩ
P-DOWN/RST
RX-LOS
THRSET
VTH
SC-RX-LOS
LOS
SC-RX-LOL
LOL
MOD-NR
EN2
FCTL2
INTERRUPT
EN1
FCTL1
AUX1MON
*
LIMITING
AMP
FCTL1
AUX2MON
SC-TX-LOS
GND
MAX3991
BMD
RSSI
FCTL2
LOS
MAX3992
EQUALIZER
RECEIVER CURRENT SENSE (VOLTAGE)
1nF
*ADDITIONAL MONITORS NOT USED IN THIS EXAMPLE.
______________________________________________________________________________________
41
DS1862A
Power-Supply Decoupling
To achieve best results, it is recommended that the
power supply is decoupled with a 0.01μF or a 0.1μF
capacitor. Use high-quality, ceramic, surface-mount
capacitors, and mount the capacitors as close as possible to the VCC2/VCC3 and GND pins to minimize lead
inductance.
DS1862A
XFP Laser Control and Digital Diagnostic IC
Chip Information
TRANSISTOR COUNT: 75,457
SUBSTRATE CONNECTED TO GROUND
Package Information
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
25 CSBGA
X25+1
56-G6013-001
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
42 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.