MAXIM MX7705EWE

19-3051; Rev 3; 6/09
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Features
The MX7705 low-power, 2-channel, serial-output analog-to-digital converter (ADC) includes a sigma-delta
modulator with a digital filter to achieve 16-bit resolution
with no missing codes. This ADC is pin compatible and
software compatible with the AD7705. The MX7705 features an on-chip input buffer and programmable-gain
amplifier (PGA). The device offers an SPI™-/QSPI™-/
MICROWIRE™-compatible serial interface.
The MX7705 operates from a single 2.7V to 5.25V supply.
The operating supply current is 320µA (typ) with a 3V
supply. Power-down mode reduces the supply current to
2µA (typ).
Self-calibration and system calibration allow the MX7705
to correct for gain and offset errors. Excellent DC performance (±0.003% FSR INL) and low noise (650nV) make
the MX7705 ideal for measuring low-frequency signals
with a wide dynamic range. The device accepts fully differential bipolar/unipolar inputs. An internal input buffer
allows for input signals with high source impedances. An
on-chip digital filter, with a programmable cutoff and output data rate, processes the output of the sigma-delta
modulator. The first notch frequency of the digital filter is
chosen to provide 150dB rejection of common-mode
50Hz or 60Hz noise and 98dB rejection of normal-mode
50Hz or 60Hz noise. A PGA and digital filtering allow signals to be directly acquired with little or no signal-conditioning requirements.
The MX7705 is available in 16-pin PDIP, SO, and
TSSOP packages.
o Pin Compatible and Software Compatible with the
AD7705
Applications
o 16-Bit Sigma-Delta ADC
o Two Fully Differential Input Channels
o 0.003% Integral Nonlinearity with No Missing Codes
o Interface with Schmitt Triggers on Inputs
o Internal Analog Input Buffers
o PGA from 1 to 128
o Single (2.7V to 3.6V) or (4.75V to 5.25V) Supply
o Low Power
1mW (max), 3V Supply
2µA (typ) Power-Down Current
o SPI-/QSPI-/MICROWIRE-Compatible 3-Wire Serial
Interface
o 16-Pin PDIP, SO, and TSSOP Packages
Ordering Information
TEMP RANGE
PIN- PACKAGE
MX7705EPE*
PART
-40°C to +85°C
16 PDIP
MX7705EWE*
-40°C to +85°C
16 WIDE SO
MX7705EUE
-40°C to +85°C
16 TSSOP
*Future product—contact factory for availability.
Industrial Instruments
Weigh Scales
Pin Configuration
Strain-Gauge Measurements
Loop-Powered Systems
Flow and Gas Meters
TOP VIEW
Medical Instrumentation
SCLK 1
16 GND
Pressure Transducers
CLKIN 2
15 VDD
Thermocouple Measurements
RTD Measurements
CLKOUT 3
CS 4
14 DIN
MX7705
13 DOUT
RESET 5
12 DRDY
AIN2+ 6
11 AIN2-
AIN1+ 7
10 REF-
AIN1- 8
9
REF+
PDIP/SO/TSSOP
SPI/QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MX7705
General Description
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
ABSOLUTE MAXIMUM RATINGS
VDD to GND ..............................................................-0.3V to +6V
All Other Pins to GND.................................-0.3V to (VDD + 0.3V)
Maximum Current Input into Any Pin ..................................50mA
Continuous Power Dissipation (TA = +70°C)
PDIP (derate 10.5mW/°C above +70°C) ......................842mW
TSSOP (derate 9.4mW/°C above +70°C) ....................755mW
Wide SO (derate 9.5mW/°C above +70°C)..................762mW
Operating Temperature Range ..........................-40°C to +85°C
Storage Temperature Range .............................-60°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = 3V or 5V, GND = 0, VREF+ = 1.225V for VDD = 3V and VREF+ = 2.5V for VDD = 5V, VREF- = GND, external fCLKIN =
2.4576MHz, CLKDIV bit = 0, CREF+ to GND = 0.1µF, CREF- to GND = 0.1µF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC ACCURACY
Resolution (No Missing Codes)
16
Output Noise
Integral Nonlinearity
Bits
Tables 1, 3
INL
Gain = 1, unbuffered
Unipolar Offset Error
After calibration
Unipolar Offset Drift
(Note 2)
Bipolar Zero Error
After calibration
µV
±0.003
%FSR
(Note 1)
µV
0.5
µV/°C
(Note 1)
µV
Gain = 1 to 4
0.5
Gain = 8 to 128
0.1
Positive Full-Scale Error
After calibration
(Notes 1, 3)
µV
Full-Scale Drift
(Notes 2, 4)
0.5
µV/°C
Gain Error
After calibration
(Notes 1, 5)
µV
Gain Drift
(Notes 2, 6)
0.5
ppm of
FSR/°C
Bipolar Negative Full-Scale Error
After calibration
±0.003
%FSR
Bipolar Negative Full-Scale Drift
(Note 2)
Gain = 8 to 128
Bipolar Zero Drift (Note 2)
Gain = 1 to 4
µV/°C
1
µV/°C
0.6
ANALOG INPUTS (AIN1+, AIN1-, AIN2+, AIN2-)
0
VREF /
GAIN
Bipolar input range
-VREF /
GAIN
VREF /
GAIN
Unbuffered
GND 30mV
VDD +
30mV
Buffered
GND +
50mV
VDD 1.5V
Unipolar input range
AIN Differential Input Voltage
Range (Note 7)
V
AIN Absolute Input Voltage
Range (Note 8)
AIN DC Leakage Current
2
V
Unselected input channel
_______________________________________________________________________________________
1
nA
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
(VDD = 3V or 5V, GND = 0, VREF+ = 1.225V for VDD = 3V and VREF+ = 2.5V for VDD = 5V, VREF- = GND, external fCLKIN =
2.4576MHz, CLKDIV bit = 0, CREF+ to GND = 0.1µF, CREF- to GND = 0.1µF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
AIN Input Capacitance
AIN Input Sampling Rate
fs
CONDITIONS
TYP
34
Gain = 2
38
Gain = 4
45
Gain = 8 to 128
60
CMR
VDD = 3V
MAX
Gain = 1
96
Gain = 2
105
Gain = 4
110
Gain = 8 to 128
130
Gain = 1
105
Gain = 2
110
Gain = 4
120
Gain = 8 to 128
130
UNITS
pF
fCLKIN /
64
Gain = 1 to 128
VDD = 5V
Input Common-Mode Rejection
MIN
Gain = 1
MHz
dB
Normal-Mode 50Hz Rejection
For filter notches of 25Hz, 50Hz,
±0.02 × fNOTCH
98
dB
Normal-Mode 60Hz Rejection
For filter notches of 20Hz, 60Hz,
±0.02 × fNOTCH
98
dB
Common-Mode 50Hz Rejection
For filter notches of 25Hz, 50Hz,
±0.02 × fNOTCH
150
dB
Common-Mode 60Hz Rejection
For filter notches of 20Hz, 60Hz,
±0.02 × fNOTCH
150
dB
EXTERNAL REFERENCE (REF+, REF-)
REF Differential Input Voltage
Range (Note 9)
VREF
VDD = 4.75V to 5.25V
1.0
3.5
VDD = 2.7V to 3.6V
1.00
1.75
REF Absolute Input Voltage Range
GND
REF Input Capacitance
REF Input Sampling Rate
Gain = 1 to 128
VDD
10
V
pF
fCLKIN /
64
fs
V
MHz
DIGITAL INPUTS (DIN, SCLK, CS, RESET)
Input High Voltage
Input Low Voltage
Input Hysteresis
Input Current
Input Capacitance
VIH
VIL
VHYST
2
V
VDD = 4.75V to 5.25V
0.8
VDD = 2.7V to 3.6V
0.4
DIN, CS, RESET
250
SCLK
500
IIN
mV
±1
5
V
µA
pF
_______________________________________________________________________________________
3
MX7705
ELECTRICAL CHARACTERISTICS (continued)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
ELECTRICAL CHARACTERISTICS (continued)
(VDD = 3V or 5V, GND = 0, VREF+ = 1.225V for VDD = 3V and VREF+ = 2.5V for VDD = 5V, VREF- = GND, external fCLKIN =
2.4576MHz, CLKDIV bit = 0, CREF+ to GND = 0.1µF, CREF- to GND = 0.1µF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
CLKIN INPUT
CLKIN Input High Voltage
VCLKINH
CLKIN Input Low Voltage
VCLKINL
CLKIN Input Current
VDD = 4.75V to 5.25V
3.5
VDD = 2.7V to 3.6V
2.5
V
VDD = 4.75V to 5.25V
0.8
VDD = 2.7V to 3.6V
0.4
ICLKIN
±10
V
µA
DIGITAL OUTPUTS (DOUT, DRDY, CLKOUT)
VDD = 5V
Output Voltage Low
VOL
VDD = 3V
VDD = 5V
Output Voltage High
VOH
VDD = 3V
Tri-State Leakage Current
Tri-State Output Capacitance
IL
DOUT only
COUT
DOUT only
DOUT and DRDY,
ISINK = 800µA
0.4
CLKOUT,
ISINK = 10µA
0.4
DOUT and DRDY,
ISINK = 100µA
0.4
CLKOUT,
ISINK = 10µA
0.4
V
DOUT and DRDY,
ISOURCE = 200µA
4.0
CLKOUT,
ISOURCE = 10µA
4.0
V
DOUT and DRDY,
ISOURCE = 100µA
VDD 0.6V
CLKOUT,
ISOURCE = 10µA
VDD 0.6V
±10
9
µA
pF
SYSTEM CALIBRATION
Full-Scale Calibration Range
GAIN = selected PGA gain (1 to 128)
(Note 10)
-1.05 ×
VREF /
GAIN
1.05 ×
VREF /
GAIN
V
Offset Calibration Range
GAIN = selected PGA gain (1 to 128)
(Note 10)
-1.05 ×
VREF /
GAIN
1.05 ×
VREF /
GAIN
V
Input Span
GAIN = selected PGA gain (1 to 128)
(Notes 10, 11)
0.8 ×
VREF /
GAIN
2.1 ×
VREF /
GAIN
V
4
_______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
(VDD = 3V or 5V, GND = 0, VREF+ = 1.225V for VDD = 3V and VREF+ = 2.5V for VDD = 5V, VREF- = GND, external fCLKIN =
2.4576MHz, CLKDIV bit = 0, CREF+ to GND = 0.1µF, CREF- to GND = 0.1µF, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.25
V
POWER REQUIREMENTS
Power-Supply Voltage
VDD
2.70
Unbuffered
fCLKIN =1MHz,
gain =1 to 128
Buffered,
fCLKIN =1MHz,
gain =1 to 128
Unbuffered,
fCLKIN = 2.4576MHz
Power-Supply Current (Note 12)
IDD
Buffered,
fCLKIN = 2.4576MHz
Power-down mode
(Note 13)
Power-Supply Rejection Ratio
PSRR
VDD = 5V
0.45
VDD = 3V
0.32
VDD = 5V
0.7
VDD = 3V
0.6
VDD = 5V,
gain = 1 to 4
0.6
VDD = 5V,
gain = 8 to 128
0.85
VDD = 3V,
gain = 1 to 4
0.4
VDD = 3V,
gain = 8 to 128
0.6
VDD = 5V,
gain = 1 to 4
0.9
VDD = 5V,
gain = 8 to 128
1.3
VDD = 3V,
gain = 1 to 4
0.7
VDD = 3V,
gain = 8 to 128
1.1
VDD = 5V
16
VDD = 3V
8
VDD = 4.75V to 5.25V
(Note 14)
VDD = 2.7V to 3.6V
(Note 14)
mA
µA
dB
EXTERNAL CLOCK TIMING SPECIFICATIONS
CLKIN Frequency
Duty Cycle
fCLKIN
(Note 15)
400
2500
kHz
40
60
%
_______________________________________________________________________________________
5
MX7705
ELECTRICAL CHARACTERISTICS (continued)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
TIMING CHARACTERISTICS
(VDD = 3V or 5V, GND = 0, VREF+ = 1.225V for VDD = 3V and VREF+ = 2.5V for VDD = 5V, VREF- = GND, external fCLKIN =
2.4576MHz, CLKDIV bit = 0, CREF+ to GND = 0.1µF, CREF- to GND = 0.1µF, TA = TMIN to TMAX, unless otherwise noted.) (Note 16)
(Figures 8, 9)
PARAMETER
SYMBOL
CONDITIONS
DRDY High Time
Reset Pulse-Width Low
MIN
TYP
MAX
UNITS
500 /
fCLKIN
s
100
ns
DRDY Fall to CS Fall Setup Time
t1
0
ns
CS Fall to SCLK Rise Setup Time
t2
120
ns
SCLK Fall to DOUT Valid Delay
t3
SCLK Pulse-Width High
t4
100
ns
SCLK Pulse-Width Low
t5
100
ns
CS Rise to SCLK Rise Hold Time
t6
VDD = 4.75V to 5.25V
0
80
VDD = 2.7V to 3.6V
0
100
0
ns
ns
VDD = 4.75V to 5.25V
60
VDD = 2.7V to 3.6V
100
Bus Relinquish Time After SCLK
Rising Edge
t7
SCLK Fall to DRDY Rise Delay
t8
DIN to SCLK Setup Time
t9
30
ns
DIN to SCLK Hold Time
t10
20
ns
6
100
_______________________________________________________________________________________
ns
ns
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
(VDD = 3V or 5V, GND = 0, VREF+ = 1.225V for VDD = 3V and VREF+ = 2.5V for VDD = 5V, VREF- = GND, external fCLKIN =
2.4576MHz, CLKDIV bit = 0, CREF+ to GND = 0.1µF, CREF- to GND = 0.1µF, TA = TMIN to TMAX, unless otherwise noted.) (Note 16)
(Figures 8, 9)
Note 1: These errors are in the order of the conversion noise shown in Tables 1 and 3. This applies after calibration at the given
temperature.
Note 2: Recalibration at any temperature removes these drift errors.
Note 3: Positive full-scale error includes zero-scale errors (unipolar offset error or bipolar zero error) and applies to both unipolar
and bipolar input ranges.
Note 4: Full-scale drift includes zero-scale drift (unipolar offset drift or bipolar zero drift) and applies to both unipolar and bipolar
input ranges.
Note 5: Gain error does not include zero-scale errors. It is calculated as (full-scale error - unipolar offset error) for unipolar ranges,
and (full-scale error - bipolar zero error) for bipolar ranges.
Note 6: Gain-error drift does not include unipolar offset drift or bipolar zero drift. Effectively, it is the drift of the part if only zeroscale calibrations are performed.
Note 7: The analog input voltage range on AIN+ is given with respect to the voltage on AIN- on the MX7705.
Note 8: This common-mode voltage range is allowed, provided that the input voltage on analog inputs does not go more positive
than (VDD + 30mV) or more negative than (GND - 30mV). Parts are functional with voltages down to (GND - 200mV), but
with increased leakage at high temperature.
Note 9: The REF differential voltage, VREF, is the voltage on REF+ referenced to REF- (VREF = VREF+ - VREF-).
Note 10: Guaranteed by design.
Note 11: These calibration and span limits apply, provided that the absolute voltage on the analog inputs does not exceed (VDD +
30mV) or go more negative than (GND - 30mV). The offset calibration limit applies to both the unipolar zero point and the
bipolar zero point.
Note 12: When using a crystal or ceramic resonator across the CLKIN and CLKOUT as the clock source for the device, the supply
current and power dissipation varies depending on the crystal or resonator type. Supply current is measured with the digital inputs connected to 0 or VDD, CLKIN connected to an external clock source, and CLKDIS = 1.
Note 13: If the external master clock continues to run in power-down mode, the power-down current typically increases to 67µA at
3V. When using a crystal or ceramic resonator across the CLKIN and CLKOUT as the clock source for the device, the
clock generator continues to run in power-down mode and the power dissipation depends on the crystal or resonator type
(see the Power-Down Modes section).
Note 14: Measured at DC and applied in the selected passband. PSRR at 50Hz exceeds 120dB with filter notches of 25Hz or 50Hz.
PSRR at 60Hz exceeds 120dB with filter notches of 20Hz or 60Hz. PSRR depends on both gain and VDD.
GAIN
PSRR (dB)
(VDD = 5V)
PSRR (dB)
(VDD = 3V)
1
90
86
2
78
78
4
84
85
8 to 128
91
93
Note 15: Provide fCLKIN whenever the MX7705 is not in power-down mode. If no clock is present, the device can draw higher than
specified current and can possibly become uncalibrated.
Note 16: All input signals are specified with tr = tf = 5ns (10% to 90% of VDD) and timed from a voltage level of 1.6V.
_______________________________________________________________________________________
7
MX7705
TIMING CHARACTERISTICS (continued)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Table 1. Output RMS Noise vs. Gain and Output Data Rate (VDD = 5V)
FILTER FIRST
NOTCH AND
OUTPUT DATA RATE
TYPICAL OUTPUT RMS NOISE (µV)
-3dB FREQUENCY
GAIN
1
2
4
8
16
32
64
128
BUFFERED (fCLKIN = 1MHz)
20Hz
5.24Hz
4.44
2.28
1.29
0.79
0.70
0.70
0.64
0.63
25Hz
6.55Hz
5.11
2.79
1.55
0.92
0.81
0.80
0.73
0.74
100Hz
26.2Hz
102.35
49.59
23.04
11.78
6.32
3.63
2.25
2.24
200Hz
52.4Hz
586.93
272.83
224.79
70.78
33.94
17.57
9.14
9.22
20Hz
5.24Hz
4.32
2.50
1.35
0.81
0.73
0.70
0.64
0.64
25Hz
6.55Hz
5.16
2.85
1.63
0.96
0.83
0.81
0.74
0.74
100Hz
26.2Hz
105.78
49.86
24.67
12.16
6.42
3.80
2.22
2.23
200Hz
52.4Hz
526.60
260.51
132.16
67.25
34.09
18.20
8.95
9.08
UNBUFFERED (fCLKIN = 1MHz)
BUFFERED (fCLKIN = 2.4576MHz)
50Hz
13.1Hz
3.53
1.86
1.09
0.73
0.72
0.71
0.67
0.66
60Hz
15.72Hz
4.41
2.23
1.29
0.83
0.79
0.77
0.72
0.73
250Hz
65.5Hz
99.66
46.85
16.98
12.48
6.38
3.78
2.32
2.35
500Hz
131Hz
608.86
288.39
110.80
67.51
36.75
17.98
9.43
9.40
3.65
1.94
1.17
0.79
0.70
0.69
0.66
0.65
UNBUFFERED (fCLKIN = 2.4576MHz)
8
50Hz
13.1Hz
60Hz
15.72Hz
4.56
2.41
1.32
0.87
0.80
0.79
0.71
0.74
250Hz
65.5Hz
101.56
49.64
25.39
12.92
6.65
3.69
2.36
2.36
500Hz
131Hz
556.06
278.91
142.88
74.78
35.41
18.99
9.80
9.44
_______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
FILTER FIRST
NOTCH AND
OUTPUT DATA RATE
MX7705
Table 2. Peak-to-Peak Resolution vs. Gain and Output Data Rate (VDD = 5V)
TYPICAL PEAK-TO-PEAK RESOLUTION (BITS)
-3dB FREQUENCY
GAIN
1
2
4
8
16
32
64
128
BUFFERED (fCLKIN = 1MHz)
20Hz
5.24Hz
16
16
16
16
16
15
14
13
25Hz
6.55Hz
16
16
16
16
16
15
14
13
100Hz
26.2Hz
12
12
12
12
12
12
12
11
200Hz
52.4Hz
10
10
10
10
10
10
10
9
UNBUFFERED (fCLKIN = 1MHz)
20Hz
5.24Hz
16
16
16
16
16
15
14
13
25Hz
6.55Hz
16
16
16
16
16
15
14
13
100Hz
26.2Hz
12
12
12
12
12
12
12
11
200Hz
52.4Hz
10
10
10
10
10
10
10
9
BUFFERED (fCLKIN = 2.4576MHz)
50Hz
13.1Hz
16
16
16
16
16
15
14
13
60Hz
15.72Hz
16
16
16
16
16
15
14
13
250Hz
65.5Hz
12
12
13
12
12
12
12
11
500Hz
131Hz
10
10
11
10
10
10
10
9
UNBUFFERED (fCLKIN = 2.4576MHz)
50Hz
13.1Hz
16
16
16
16
16
15
14
13
60Hz
15.72Hz
16
16
16
16
16
15
14
13
250Hz
65.5Hz
12
12
12
12
12
12
12
11
500Hz
131Hz
10
10
10
10
10
10
10
9
_______________________________________________________________________________________
9
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Table 3. Output RMS Noise vs. Gain and Output Data Rate (VDD = 3V)
FILTER FIRST
NOTCH AND
OUTPUT DATA RATE
TYPICAL OUTPUT RMS NOISE (µV)
-3dB FREQUENCY
GAIN
1
2
4
8
16
32
64
128
3.52
1.84
2.19
0.73
0.66
0.62
0.62
0.62
BUFFERED (fCLKIN = 1MHz)
20Hz
5.24Hz
25Hz
6.55Hz
4.24
2.23
1.19
0.84
0.74
0.69
0.69
0.69
100Hz
26.2Hz
50.36
25.12
12.06
6.04
3.38
2.23
1.70
1.69
200Hz
52.4Hz
268.02
175.98
65.77
34.89
16.73
8.76
4.70
4.70
3.58
1.92
1.13
0.72
0.66
0.64
0.61
0.62
UNBUFFERED (fCLKIN = 1MHz)
20Hz
5.24Hz
25Hz
6.55Hz
4.16
2.27
1.27
0.83
0.74
0.70
0.69
0.67
100Hz
26.2Hz
50.48
23.89
12.10
5.90
3.26
0.70
1.66
1.63
200Hz
52.4Hz
256.43
135.78
65.62
33.18
16.65
8.47
4.66
4.68
BUFFERED (fCLKIN = 2.4576MHz)
50Hz
13.1Hz
2.84
1.68
2.00
0.71
0.67
0.65
0.63
0.61
60Hz
15.72Hz
3.27
1.84
1.12
0.78
0.75
0.70
0.68
0.67
250Hz
65.5Hz
47.90
24.43
12.56
6.48
3.45
2.32
1.64
1.66
500Hz
131Hz
281.03
104.19
69.58
34.59
17.44
9.20
5.16
4.92
UNBUFFERED (fCLKIN = 2.4576MHz)
10
50Hz
13.1Hz
3.04
1.74
1.03
0.72
0.64
0.64
0.62
0.63
60Hz
15.72Hz
3.35
1.80
1.13
0.81
0.73
0.69
0.67
0.68
250Hz
65.5Hz
49.63
23.82
13.03
6.23
3.42
2.22
1.68
1.65
500Hz
131Hz
279.13
134.82
69.47
35.42
17.47
9.55
4.90
5.18
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
FILTER FIRST
NOTCH AND
OUTPUT DATA RATE
MX7705
Table 4. Peak-to-Peak Resolution vs. Gain and Output Data Rate (VDD = 3V)
TYPICAL PEAK-TO-PEAK RESOLUTION (BITS)
-3dB FREQUENCY
GAIN
1
2
4
8
16
32
64
128
BUFFERED (fCLKIN = 1MHz)
20Hz
5.24Hz
16
16
16
16
15
14
13
12
25Hz
6.55Hz
16
16
16
16
15
14
13
12
100Hz
26.2Hz
12
12
12
12
12
12
12
11
200Hz
52.4Hz
10
10
10
10
10
10
10
9
20Hz
5.24Hz
16
16
16
16
15
14
13
12
UNBUFFERED (fCLKIN = 1MHz)
25Hz
6.55Hz
16
16
16
16
15
14
13
12
100Hz
26.2Hz
12
12
12
12
12
14
12
11
200Hz
52.4Hz
10
10
10
10
10
10
10
9
BUFFERED (fCLKIN = 2.4576MHz)
50Hz
13.1Hz
16
16
16
16
15
14
13
12
60Hz
15.72Hz
16
16
16
16
15
14
13
12
250Hz
65.5Hz
12
12
12
12
12
12
11
11
500Hz
131Hz
10
11
10
10
10
10
10
9
UNBUFFERED (fCLKIN = 2.4576MHz)
50Hz
13.1Hz
16
16
16
16
15
14
13
12
60Hz
15.72Hz
16
16
16
16
15
14
13
12
250Hz
65.5Hz
12
12
12
12
12
12
11
11
500Hz
131Hz
10
10
10
10
10
10
10
9
Typical Operating Characteristics
(VDD = 3V or 5V, VREF+ = 1.225V for VDD = 3V, VREF+ = 2.5V for VDD = 5V, VREF- = GND, TA = +25°C, unless otherwise noted.)
32772
RMS NOISE = 1.3μV
OCCURENCE
32768
32766
32764
VDD = 3V
0.0010
OFFSET ERROR (%FSR)
300
32770
200
0.0005
0
-0.0005
32762
100
32760
-0.0010
32758
32756
0
0
400
800
1200
READING NUMBER
1600
2000
32760
32761
32762
32763
32764
32765
32766
32767
32768
32769
32770
32771
32772
32773
CODE READ
VDD = 5V, VREF = 2.5V
GAIN = 128
ODR = 60Hz
0.0015
MX7705 toc02
GAIN = 128
ODR = 60Hz
RMS NOISE = 1.3μV
MX7705 toc01
VDD = 5V,
VREF = 2.5V
32774
OFFSET ERROR vs. SUPPLY VOLTAGE (3V)
HISTOGRAM OF TYPICAL OUTPUT NOISE
400
MX7705 toc03
TYPICAL OUTPUT NOISE
32776
CODE
-0.0015
2.70
2.85
3.00
3.15
3.30
3.45
3.60
SUPPLY VOLTAGE (V)
______________________________________________________________________________________
11
Typical Operating Characteristics (continued)
(VDD = 3V or 5V, VREF+ = 1.225V for VDD = 3V, VREF+ = 2.5V for VDD = 5V, VREF- = GND, TA = +25°C, unless otherwise noted.)
0
-0.001
-0.002
0.001
0
VDD = 3V
4.85
4.95
5.05
5.15
5.25
-0.0015
-40
-15
SUPPLY VOLTAGE (V)
10
35
60
2.70
85
2.85
0.004
0.003
GAIN ERROR (%FSR)
0.001
0
-0.001
MX7705 toc08
0.005
MX7705 toc07
VDD = 5V
3.15
GAIN ERROR vs. TEMPERATURE
GAIN ERROR vs. SUPPLY VOLTAGE (5V)
0.002
3.00
VDD = 3V
0.002
0.001
0
-0.001
-0.002
-0.003
-0.002
VDD = 5V
-0.004
-0.005
-0.003
4.75
4.85
4.95
5.05
SUPPLY VOLTAGE (V)
12
5.15
5.25
3.30
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
0.003
GAIN ERROR (%FSR)
0
-0.0010
-0.003
4.75
0.0005
-0.0005
-0.001
-0.002
-0.003
MX7705 toc06
VDD = 3V
0.0010
GAIN ERROR (%FSR)
OFFSET ERROR (%FSR)
0.001
VDD = 5V
0.002
0.0015
MX7705 toc05
0.003
MX7705 toc04
VDD = 5V
0.002
GAIN ERROR vs. SUPPLY VOLTAGE (3V)
OFFSET ERROR vs. TEMPERATURE
OFFSET ERROR vs. SUPPLY VOLTAGE (5V)
0.003
OFFSET ERROR (%FSR)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
-40
-15
10
35
60
85
TEMPERATURE (°C)
______________________________________________________________________________________
3.45
3.60
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
0.5
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
MX7705 toc09
VDD = 3V
A
B
0.4
C
D
0.3
0.65
A
MX7705 toc10
SUPPLY CURRENT vs. SUPPLY VOLTAGE (5V)
SUPPLY CURRENT vs. SUPPLY VOLTAGE (3V)
0.6
VDD = 5V
B
0.55
0.45
C
D
0.35
E
E
0.25
0.2
2.70
2.85
3.00
3.15
3.30
3.45
4.75
3.60
4.85
4.95
5.05
5.15
5.25
SUPPLY VOLTAGE (V)
A: BUFFERED MODE
B: BUFFERED MODE C: BUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 2.4576MHz, fCLKIN = 1MHz,
GAIN = 8 TO 128
GAIN = 1 TO 4
GAIN = 1 TO 128
SUPPLY VOLTAGE (V)
A: BUFFERED MODE
B: BUFFERED MODE C: BUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 2.4576MHz, fCLKIN = 1MHz,
GAIN = 8 TO 128
GAIN = 1 TO 4
GAIN = 1 TO 128
D: UNBUFFERED MODE E: UNBUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 1MHz,
GAIN = 1 TO 128
GAIN = 1 TO 128
D: UNBUFFERED MODE E: UNBUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 1MHz,
GAIN = 1 TO 128
GAIN = 1 TO 128
SUPPLY CURRENT vs. TEMPERATURE (3V)
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
0.5
B
C
0.4
D
0.3
A
MX7705 toc12
VDD = 3V
A
SUPPLY CURRENT vs. TEMPERATURE (5V)
0.65
MX7705 toc11
0.6
VDD = 5V
B
0.55
C
0.45
D
0.35
E
E
0.2
0.25
-40
-15
10
35
60
85
-40
-15
10
35
60
85
TEMPERATURE (°C)
A: BUFFERED MODE
B: BUFFERED MODE C: BUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 2.4576MHz, fCLKIN = 1MHz,
GAIN = 8 TO 128
GAIN = 1 TO 4
GAIN = 1 TO 128
TEMPERATURE (°C)
A: BUFFERED MODE
B: BUFFERED MODE C: BUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 2.4576MHz, fCLKIN = 1MHz,
GAIN = 8 TO 128
GAIN = 1 TO 4
GAIN = 1 TO 128
D: UNBUFFERED MODE E: UNBUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 1MHz,
GAIN = 1 TO 128
GAIN = 1 TO 128
D: UNBUFFERED MODE E: UNBUFFERED MODE
fCLKIN = 2.4576MHz,
fCLKIN = 1MHz,
GAIN = 1 TO 128
GAIN = 1 TO 128
______________________________________________________________________________________
13
MX7705
Typical Operating Characteristics (continued)
(VDD = 3V or 5V, VREF+ = 1.225V for VDD = 3V, VREF+ = 2.5V for VDD = 5V, VREF- = GND, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VDD = 3V or 5V, VREF+ = 1.225V for VDD = 3V, VREF+ = 2.5V for VDD = 5V, VREF- = GND, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT vs. fCLKIN (3V)
0.5
0.4
C
D
0.3
VDD = 5V
MX7705 toc14
B
SUPPLY CURRENT (mA)
B
A
0.55
0.45
C
D
0.35
E
E
0.2
0.25
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6
fCLKIN (MHz)
B: BUFFERED MODE
CLK = 1,
GAIN = 1
A: BUFFERED MODE
CLK = 1,
GAIN = 128
C: BUFFERED MODE
CLK = 0,
GAIN = 1, 128
D: UNBUFFERED MODE E: UNBUFFERED MODE
CLK = 1,
CLK = 0,
GAIN = 1, 128
GAIN = 1, 128
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6
SUPPLY CURRENT vs. GAIN (3V)
SUPPLY CURRENT vs. GAIN (5V)
C
D
0.3
VDD = 5V
A
B
SUPPLY CURRENT (mA)
B
0.4
0.65
MX7705 toc15
A
0.5
C: BUFFERED MODE
CLK = 0,
GAIN = 1, 128
D: UNBUFFERED MODE E: UNBUFFERED MODE
CLK = 1,
CLK = 0,
GAIN = 1, 128
GAIN = 1, 128
0.6
VDD = 3V
fCLKIN (MHz)
B: BUFFERED MODE
CLK = 1,
GAIN = 1
A: BUFFERED MODE
CLK = 1,
GAIN = 128
0.55
0.45
C
D
E
0.35
E
MX7705 toc16
SUPPLY CURRENT (mA)
VDD = 3V
A
SUPPLY CURRENT vs. fCLKIN (5V)
0.65
MX7705 toc13
0.6
SUPPLY CURRENT (mA)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
F
F
0.2
0.25
1
14
2
4
8
16
32
64
128
1
2
4
8
16
32
64
128
GAIN
A: BUFFERED MODE
B: BUFFERED MODE C: BUFFERED MODE
CLK = 1, CLKDIV = 1,
CLK = 1, CLKDIV = 0, CLK = 0, CLKDIV = 0,
fCLKIN = 2.4576MHz
fCLKIN = 1MHz
fCLKIN = 2.4576MHz
GAIN
A: BUFFERED MODE
B: BUFFERED MODE C: BUFFERED MODE
CLK = 1, CLKDIV = 0,
CLK = 1, CLKDIV = 1, CLK = 0, CLKDIV = 0,
fCLKIN = 2.4576MHz
fCLKIN = 1MHz
fCLKIN = 2.4576MHz
D: UNBUFFERED MODE E: UNBUFFERED MODE F: UNBUFFERED MODE
CLK = 1, CLKDIV = 1,
CLK = 1, CLKDIV = 0, CLK = 0, CLKDIV = 0,
fCLKIN = 2.4576MHz
fCLKIN = 2.4576MHz
fCLKIN = 1MHz
D: UNBUFFERED MODE E: UNBUFFERED MODE F: UNBUFFERED MODE
CLK = 1, CLKDIV = 1,
CLK = 1, CLKDIV = 0, CLK = 0, CLKDIV = 0,
fCLKIN = 2.4576MHz
fCLKIN = 2.4576MHz
fCLKIN = 1MHz
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
60
40
20
0
200
VDD = 5V
180
160
140
120
300
250
VDD = 5V
200
150
100
100
2.70
2.85
3.00
3.15
3.30
SUPPLY VOLTAGE (V)
3.45
3.60
MX7705 toc19
80
POWER-DOWN SUPPLY CURRENT
vs. TEMPERATURE
MX7705 toc18
VDD = 3V
POWER-DOWN SUPPLY CURRENT (nA)
MX7705 toc17
POWER-DOWN SUPPLY CURRENT (nA)
100
POWER-DOWN SUPPLY CURRENT
vs. SUPPLY VOLTAGE (5V)
POWER-DOWN SUPPLY CURRENT (μA)
POWER-DOWN SUPPLY CURRENT
vs. SUPPLY VOLTAGE (3V)
VDD = 3V
50
0
4.75
4.85
4.95
5.05
5.15
5.25
SUPPLY VOLTAGE (V)
-40
-15
10
35
60
85
TEMPERATURE (°C)
EXTERNAL OSCILLATOR STARTUP TIME
MX7705 toc20
VDD
5V/div
4.9152MHz CRYSTAL
CLKOUT
5V/div
CLKOUT
5V/div
2.4576MHz CRYSTAL
2ms/div
______________________________________________________________________________________
15
MX7705
Typical Operating Characteristics (continued)
(VDD = 3V or 5V, VREF+ = 1.225V for VDD = 3V, VREF+ = 2.5V for VDD = 5V, VREF- = GND, TA = +25°C, unless otherwise noted.)
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
MX7705
Pin Description
16
PIN
NAME
FUNCTION
1
SCLK
Serial Clock Input. Apply an external serial clock to transfer data to and from the device at data rates
of up to 5MHz.
2
CLKIN
Clock Input. Connect a crystal/resonator between CLKIN and CLKOUT, or drive CLKIN externally with
a CMOS-compatible clock source with CLKOUT left unconnected.
3
CLKOUT
4
CS
5
RESET
Active-Low Reset Input. Drive RESET low to reset the MX7705 to power-on reset status.
6
AIN2+
Channel 2 Positive Differential Analog Input
7
AIN1+
Channel 1 Positive Differential Analog Input
8
AIN1-
Channel 1 Negative Differential Analog Input
9
REF+
Positive Differential Reference Input
Clock Output. Connect a crystal/resonator between CLKIN and CLKOUT. When enabled, CLKOUT
provides a CMOS-compatible, inverted clock output. Set CLKDIS = 0 in the clock register to enable
CLKOUT. Set CLKDIS = 1 in the clock register to disable CLKOUT to conserve power.
Active-Low Chip-Select Input. CS selects the active device in systems with more than one device on
the serial bus. Drive CS low to clock data in on DIN and to clock data out on DOUT. When CS is high,
DOUT is high impedance. Connect CS to GND for 3-wire operation.
10
REF-
Negative Differential Reference Input
11
AIN2-
Channel 2 Negative Differential Analog Input
12
DRDY
Active-Low Data-Ready Output. DRDY goes low when a new conversion result is available in the data
register. When a read-operation of a full output word completes, DRDY returns high.
13
DOUT
Serial Data Output. DOUT outputs serial data from the data register. DOUT changes on the falling
edge of SCLK and is valid on the rising edge of SCLK. When CS is high, DOUT is high impedance.
14
DIN
Serial Data Input. Data on DIN is clocked in on the rising edge of SCLK when CS is low.
15
VDD
Power Input
16
GND
Ground
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
DIVIDER
CLOCK
GENERATOR
CLKIN
CLKOUT
MX7705
BUFFER
AIN1+
AIN1AIN2+
SWITCHING
NETWORK
S1
S2
PGA
2ND-ORDER
SIGMA-DELTA
MODULATOR
DIGITAL
FILTER
VDD
GND
AIN2BUFFER
S1 AND S2 ARE OPEN IN
BUFFERED MODE AND CLOSED
IN UNBUFFERED MODE
REF+
SERIAL INTERFACE,
REGISTERS,
AND
CONTROL
CS
SCLK
DIN
DOUT
DRDY
RESET
REF-
Detailed Description
The MX7705 low-power, 2-channel, serial-output ADC
uses a sigma-delta modulator with a digital filter to
achieve 16-bit resolution with no missing codes. The
device includes a PGA, an on-chip input buffer, and a
bidirectional communications port. The MX7705 operates with a single 2.7V to 5.25V supply.
Fully differential inputs, an internal input buffer, and an
on-chip PGA (gain = 1 to 128) allow low-level signals to
be directly measured, minimizing the requirements for
external signal conditioning. Self-calibration corrects for
gain and offset errors. A programmable digital filter
allows for the selection of the output data rate and firstnotch frequency from 20Hz to 500Hz.
The bidirectional serial SPI-/QSPI-/MICROWIRE-compatible interface consists of four digital control lines (SCLK,
CS, DOUT, and DIN) and provides an easy interface to
microcontrollers (µCs). Connect CS to GND to configure
the MX7705 for 3-wire operation.
Analog Inputs
The MX7705 accepts four analog inputs (AIN1+, AIN1-,
AIN2+, and AIN2-) in buffered or unbuffered mode.
Use Table 8 to select the positive and negative input
pair for a fully differential channel. The input buffer isolates the inputs from the capacitive load presented by
the PGA/modulator, allowing for high source-impedance analog transducers. The value of the BUF bit in
the setup register (see the Setup Register section) determines whether the input buffer is enabled or disabled.
Internal protection diodes, which clamp the analog
input to VDD and/or GND, allow the input to swing from
(GND - 0.3V) to (VDD + 0.3V), without damaging the
device. If the analog input exceeds 300mV beyond the
supplies, limit the input current to 10mA.
Input Buffers
When the analog input buffer is disabled, the analog
input drives a typical 7pF (gain = 1) capacitor, CTOTAL,
in series with the 7kΩ typical on-resistance of the track
and hold (T/H) switch (Figure 1). CTOTAL is comprised
of the sampling capacitor, CSAMP, and the stray capacitance, CSTRAY. During the conversion, CSAMP charges
to (AIN+ - AIN-). The gain determines the value of
CSAMP (Table 5).
______________________________________________________________________________________
17
MX7705
Functional Diagram
To minimize gain errors in unbuffered mode, select a
source impedance less than the maximum values
shown in Figures 2 and 3. These are the maximum
external resistance/capacitance combinations allowed
before gain errors greater than 1 LSB are introduced in
unbuffered mode.
Enable the internal input buffer for a high source impedance. This isolates the inputs from the sampling capacitor and reduces the sampling-related gain error. When
using the internal buffer, limit the absolute input voltage
range to (VGND + 50mV) to (VDD - 1.5V). Set gain and
common-mode voltage range properly to minimize linearity errors.
AIN(+)
RSW (7kΩ TYP)
HIGH
IMPEDANCE
AIN(-)
CTOTAL(7pF TYP FOR GAIN = 1)
CTOTAL = CSAMP + CSTRAY
VBIAS
Figure 1. Unbuffered Analog Input Structure
Input Voltage Range
Reference
The MX7705 provides differential inputs, REF+ and REF-,
for an external reference voltage. Connect the external
reference directly across REF+ and REF- to obtain the
differential reference voltage, VREF. The common-mode
voltage range for VREF+ and VREF- is between GND
and VDD. For specified operation, the nominal voltage,
VREF (VREF+ - VREF-), is 2.5V for VDD = 4.75V to 5.25V
and 1.225V for VDD = 2.7V to 3.6V.
The MX7705 samples REF+ and REF- at fCLKIN / 64
(CLKDIV = 0) or fCLKIN / 128 (CLKDIV = 1) with an
internal 10pF (typ for gain = 1) sampling capacitor in
series with a 7kΩ (typ) switch on-resistance.
Programmable-Gain Amplifier
A PGA provides selectable levels of gain: 1, 2, 4, 8, 16,
32, 64, and 128. Bits G0, G1, and G2 in the setup register control the gain (Table 9). As the gain increases,
the value of the input sampling capacitor, CSAMP, also
increases (Table 5). The dynamic load presented to the
analog inputs increases with clock frequency and gain
in unbuffered mode (see the Input Buffers section and
Figure 1).
100
EXTERNAL RESISTANCE (kΩ)
In unbuffered mode, the absolute analog input voltage
range is from (GND - 30mV) to (VDD + 30mV) (see the
Electrical Characteristics). In buffered mode, the analog input voltage range is reduced to (GND + 50mV) to
(VDD - 1.5V). In both buffered and unbuffered modes,
the differential analog input range (V AIN+ - V AIN- )
decreases at higher gains (see the Programmable-Gain
Amplifier and the Unipolar and Bipolar Modes sections).
GAIN = 1
GAIN = 2
10
GAIN = 4
GAIN = 8 TO 128
1
0.1
1
10
100
1000
10,000
EXTERNAL CAPACITANCE (pF)
Figure 2. Maximum External Resistance vs. Maximum External
Capacitance for Unbuffered Mode (1MHz)
100
EXTERNAL RESISTANCE (kΩ)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
GAIN = 1
GAIN = 2
10
GAIN = 4
1
GAIN = 8 TO 128
0.1
1
10
100
1000
10,000
EXTERNAL CAPACITANCE (pF)
Figure 3. Maximum External Resistance vs. Maximum External
Capacitance for Unbuffered Mode (2.4576MHz)
18
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
MX7705
Table 5. Input Sampling Capacitor vs. Gain
VREF / GAIN
INPUT SAMPLING CAPACITOR (CSAMP) (pF)
3.75
15
8–128
30
Increasing the gain increases the resolution of the ADC
(LSB size decreases), but reduces the differential input
voltage range. Calculate 1 LSB in unipolar mode using
the following equation:
1111 1111 1111 1101
0000 0000 0000 0001
0000 0000 0000 0000
0
Unipolar and Bipolar Modes
The B/U bit in the setup register (Table 9) configures
the MX7705 for unipolar or bipolar transfer functions.
Figures 4 and 5 illustrate the unipolar and bipolar transfer functions, respectively.
In unipolar mode, the digital output code is straight
binary. When AIN+ = AIN-, the outputs are at zero
scale, which is the lower endpoint of the transfer function. The full-scale endpoint is given by AIN+ - AIN- =
VREF / GAIN, where VREF = VREF+ - VREF-.
In bipolar mode, the digital output code is in offset
binary. Positive full scale is given by AIN+ - AIN- =
+VREF / GAIN and negative full scale is given by AIN+ AIN- = -VREF / GAIN. When AIN+ = AIN-, the outputs
are at zero scale, which is the midpoint of the bipolar
transfer function.
1
2
3
65,533
DIFFERENTIAL INPUT VOLTAGE (LSB)
65,535
Figure 4. MX7705 Unipolar Transfer Function
VREF / GAIN
VREF / GAIN
1111 1111 1111 1111
1111 1111 1111 1110
1111 1111 1111 1101
1 LSB =
BINARY OUTPUT CODE
where VREF = VREF+ - VREF-.
VREF
(GAIN) (65,536)
0000 0000 0000 0010
Calculate 1 LSB in bipolar mode using the following
equation:
VREF
1 LSB =
× 2
GAIN (65,536)
1 LSB =
0000 0000 0000 0011
VREF
1 LSB =
GAIN (65,536)
where VREF = VREF+ - VREF-.
For a gain of one and VREF = 2.5V, the full-scale voltage in unipolar mode is 2.5V and 1 LSB ≈ 38.1µV. For a
gain of four, the full-scale voltage in unipolar mode is
0.625V (VREF / GAIN) and 1 LSB ≈ 9.5µV. The differential input voltage range in this example reduces from
2.5V to 0.625V, and the resolution increases, since the
LSB size decreased from 38.1µV to 9.5µV.
1111 1111 1111 1100
VREF / GAIN
7.5
4
VREF / GAIN
2
FULL-SCALE TRANSITION
1111 1111 1111 1110
VREF
(GAIN) (65,536)
x2
1000 0000 0000 0001
1000 0000 0000 0000
0111 1111 1111 1111
VREF / GAIN
1
1111 1111 1111 1111
BINARY OUTPUT CODE
GAIN
0000 0000 0000 0010
0000 0000 0000 0001
0000 0000 0000 0000
-32,768
-32,766
-1
0
+1
+32,765
+32,767
DIFFERENTIAL INPUT VOLTAGE (LSB)
Figure 5. MX7705 Bipolar Transfer Function
When the MX7705 is in buffered mode, the absolute and
common-mode analog input voltage ranges reduce to
between (GND + 50mV) and (VDD - 1.5V). The differential
input voltage range is not affected in buffered mode.
______________________________________________________________________________________
19
Modulator
The MX7705 performs analog-to-digital conversions
using a single-bit, 2nd-order, switched-capacitor,
sigma-delta modulator. The sigma-delta modulation
converts the input signal into a digital pulse train whose
average duty cycle represents the digitized signal information. A single comparator within the modulator quantizes the input signal at a much higher sample rate than
the bandwidth of the input.
The MX7705 modulator provides 2nd-order frequency
shaping of the quantization noise resulting from the single-bit quantizer. The modulator is fully differential for
maximum signal-to-noise ratio and minimum susceptibility to power-supply and common-mode noise. A single-bit data stream is then presented to the digital filter
for processing to remove the frequency-shaped quantization noise.
The modulator sampling frequency is f CLKIN / 128,
regardless of gain, where fCLKIN (CLKDIV = 0) is the
frequency of the signal at CLKIN.
Digital Filtering
The MX7705 contains an on-chip, digital lowpass filter
that processes the 1-bit data stream from the modulator
using a SINC3 (sinx/x)3 response. The SINC3 filter has a
settling time of three output data periods.
Filter Characteristics
Figure 6 shows the filter frequency response. The
SINC3 characteristic -3dB cutoff frequency is 0.262
times the first-notch frequency. This results in a cutoff
frequency of 15.72Hz for a first filter-notch frequency of
60Hz (output data rate of 60Hz). The response shown
in Figure 5 is repeated at either side of the digital filter’s
sample frequency, fM (fM = 19.2kHz for 60Hz output
data rate), and at either side of the related harmonics
(2fM, 3fM, etc.).
0
fCLKIN = 2.4576MHz
CLK = 1
FS1 = 0
FS0 = 1
fN = 60Hz
-20
-40
GAIN (dB)
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
-60
-80
-100
-120
-140
-160
0
The output data rate for the digital filter corresponds with
the positioning of the first notch of the filter’s frequency
response. Therefore, for the plot in Figure 6, where the first
notch of the filter is 60Hz, the output data rate is 60Hz. The
notches of the SINC3 filter are repeated at multiples of the
first notch frequency. The SINC3 filter provides an attenuation of better than 100dB at these notches.
Determine the cutoff frequency of the digital filter by loading the appropriate values into the CLK, FS0, and FS1
bits in the clock register (Table 13). Programming a different cutoff frequency with FS0 and FS1 changes the frequency of the notches, but it does not alter the profile of
the frequency response.
For step changes at the input, allow a settling time
before valid data is read. The settling time depends on
the output data rate chosen for the filter. The worstcase settling time of a SINC3 filter for a full-scale step
input is four times the output data period. By synchronizing the step input using FSYNC, the settling time
reduces to three times the output data period. If FSYNC
is high during the step input, the filter settles in three
times the output data period after FSYNC falls low.
Analog Filtering
The digital filter does not provide any rejection close to
the harmonics of the modulator sample frequency. Due
to the high oversampling ratio of the MX7705, these
bands occupy only a small fraction of the spectrum and
most broadband noise is filtered. The analog filtering
requirements in front of the MX7705 are reduced compared to a conventional converter with no on-chip filtering.
In addition, the devices provide excellent common-mode
rejection of 90db to reduce the common-mode noise susceptibility.
Additional filtering prior to the MX7705 eliminates
unwanted frequencies the digital filter does not reject.
Use additional filtering to ensure that differential noise
signals outside the frequency band of interest do not
saturate the analog modulator.
If passive components are in the path of the analog
inputs when the device is in unbuffered mode, ensure
the source impedance is low enough (Figure 2) not to
introduce gain errors in the system. This significantly
limits the amount of passive anti-aliasing filtering that
can be applied in front of the MX7705 in unbuffered
mode. In buffered mode, large source impedance
causes a small DC-offset error, which can be removed
by calibration.
20 40 60 80 100 120 140 160 180 200
FREQUENCY (Hz)
Figure 6. Frequency Response of the SINC3 Filter (Notch at 60Hz)
20
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Serial-Digital Interface
The MX7705 interface is fully compatible with SPI-, QSPI-,
and MICROWIRE-standard serial interfaces. The serial
interface provides access to seven on-chip registers. The
registers are 8, 16, and 24 bits in size.
Drive CS low to transfer data in and out of the MX7705.
Clock in data at DIN on the rising edge of SCLK. Data at
DOUT changes on the falling edge of SCLK and is valid
on the rising edge of SCLK. DIN and DOUT are transferred MSB first. Drive CS high to force DOUT high
impedance and cause the MX7705 to ignore any signals
on SCLK and DIN. Connect CS low for 3-wire operation.
Figures 8 and 9 show the timings for write and read
operations, respectively.
On-Chip Registers
The MX7705 contains seven internal registers (Figure 10),
which are accessed by the serial interface. These registers control the various functions of the device and allow
the results to be read. Table 7 lists the address, power-on
default value, and size of each register.
The first of these registers is the communications register.
The 8-bit communications register controls the acquisition
channel selection, whether the next data transfer is a read
or write operation, and which register is to be accessed.
CRYSTAL OR
CERAMIC
RESONATOR
CLKIN
CL
MX7705
CLKOUT
CL
OPTIONAL
1MΩ
Figure 7. Using a Crystal or Ceramic Oscillator
MX7705
External Oscillator
The oscillator requires time to stabilize when enabled.
Startup time for the oscillator depends on supply voltage,
temperature, load capacitances, and center frequency.
Depending on the load capacitance, a 1MΩ feedback
resistor across the crystal can reduce the startup time
(Figure 7). The MX7705 was tested with an ECS-24-32-1
(2.4576MHz crystal) and an ECS-49-20-1 (4.9152MHz
crystal) (see the Typical Operating Characteristics). In
power-down mode, the supply current with the external
oscillator enabled is typically 67µA with a 3V supply and
227µA with a 5V supply.
CS
t6
t2
SCLK
t10
t9
DIN
MSB
LSB
Figure 8. Write Timing Diagram
DRDY
t8
t1
CS
t2
t6
t4
SCLK
t5
t3
DOUT
MSB
t7
LSB
Figure 9. Read Timing Diagram
The second register is the 8-bit setup register, which controls calibration modes, gain setting, unipolar/bipolar
inputs, and buffered/unbuffered modes. The third register
is the 8-bit clock register, which sets the digital filter characteristics and the clock control bits. The fourth register is
the 16-bit data register, which holds the output result. The
24-bit offset and gain registers store the calibration coefficients for the MX7705. The 8-bit test register is used for
factory testing only.
The default state of the MX7705 is to wait for a write to
the communications register. Any write or read operation on the MX7705 is a two-step process. First, a command byte is written to the communications register.
This command selects the input channel, the desired
register for the next read or write operation, and
whether the next operation is a read or a write. The second step is to read from or write to the selected register. At the end of the data-transfer cycle, the device
returns to the default state. See the Performing a
Conversion section for examples.
If the serial communication is lost, write 32 ones to the
serial interface to return the MX7705 to the default
state. The registers are not reset after this operation.
______________________________________________________________________________________
21
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
DIN
RS2 RS1 RS0
COMMUNICATIONS REGISTER
SETUP REGISTER (8 BITS)
CLOCK REGISTER (8 BITS)
REGISTER
SELECT
DECODER
DATA REGISTER (16 BITS)
DOUT
TEST REGISTER (8 BITS)*
OFFSET REGISTER (24 BITS)
GAIN REGISTER (24 BITS)
*THE TEST REGISTER IS USED FOR FACTORY TESTING ONLY.
Figure 10. Register Summary
Communications Register
The byte-wide communications register is bidirectional
so it can be written and read. The byte written to the
communications register indicates the next read or write
operation on the selected register, the power-down
mode, and the analog input channel (Table 6). The
DRDY bit indicates the conversion status.
0/DRDY: (Default = 0) Communication-Start/Data-Ready
Bit. Write a 0 to the 0/DRDY bit to start a write operation to
the communications register. If 0/DRDY = 1, then the
device waits until a 0 is written to 0/DRDY before continuing to load the remaining bits. For a read operation, the
0/DRDY bit shows the status of the conversion. The
DRDY bit returns a 0 if the conversion is complete and
the data is ready. DRDY returns a 1 if the new data has
been read and the next conversion is not yet complete. It
has the same value as the DRDY output pin.
RS2, RS1, RS0: (Default = 0, 0, 0) Register-Select Bits.
RS0, RS1, and RS2 select the next register to be
accessed as shown in Table 7.
R/W: (Default = 0) Read-/Write-Select Bit. Use this bit to
select if the next register access is a read or a write
operation. Set R/W = 0 to select a write operation or set
R/W = 1 for a read operation on the selected register.
22
PD: (Default = 0) Power-Down Control Bit. Set PD = 1
to initiate power-down mode. Set PD = 0 to take the
device out of power-down mode. If CLKDIS = 0, CLKOUT
remains active during power-down mode to provide a
clock source for other devices in the system.
CH0, CH1: (Default = 0, 0) Channel-Select Bit. Write to
the CH0 and CH1 bits to select the conversion channel or
to access the calibration data shown in Table 8. The calibration coefficients of a particular channel are stored in
one of the three offset and gain-register pairs in Table 8.
Set CH1 = 1 and CH0 = 0 to evaluate the noise performance of the part without external noise sources. In this
noise evaluation mode, connect AIN1- to an external voltage within the allowable common-mode range.
Setup Register
The byte-wide setup register is bidirectional, so it can
be written and read. The byte written to the setup register sets the calibration modes, PGA gain, unipolar/bipolar mode, buffer enable, and conversion start (Table 9).
MD1, MD0: (Default = 0, 0) Mode-Select Bits. See
Table 10 for normal operating mode, self-calibration,
zero-scale calibration, or full-scale calibration-mode
selection.
G2, G1, G0: (Default = 0, 0, 0) Gain-Selection Bits. See
Table 11 for PGA gain settings.
B/U: (Default = 0) Bipolar/Unipolar Mode Selection. Set
B/U = 0 to select bipolar mode. Set B/U = 1 to select
unipolar mode.
BUF: (Default = 0) Buffer-Enable Bit. For unbuffered
mode, disable the internal buffer of the MX7705 to reduce
power consumption by writing a 0 to the BUF bit. Write a
1 to this bit to enable the buffer. Use the internal buffer
when acquiring high source-impedance input signals.
FSYNC: (Default = 1) Filter-Synchronization/
Conversion-Start Bit. Set FSYNC = 0 to begin calibration
or conversion. The MX7705 performs free-running conversions while FSYNC = 0. Set FSYNC = 1 to stop converting data and to hold the nodes of the digital filter, the
filter-control logic, the calibration-control logic, and the
analog modulator in a reset state. The DRDY output does
not reset high if it is low (indicating that valid data has not
yet been read from the data register) when FSYNC goes
high. To clear the DRDY output, read the data register.
Clock Register
The byte-wide clock register is bidirectional, so it can
be written and read. The byte written to the setup register sets the clock, filter first-notch frequency, and the
output data rate (Table 12).
MXID: (Default = 1) Maxim-Identifier Bit. This is a readonly bit. Values written to this bit are ignored.
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
FIRST BIT (MSB)
FUNCTION
(LSB)
COMMUNICATION
START/DATA READY
Name
REGISTER SELECT
READ/WRITE
SELECT
POWER-DOWN
MODE
CHANNEL SELECT
0/DRDY
RS2
RS1
RS0
R/W
PD
CH1
CH0
0
0
0
0
0
0
0
0
Defaults
Table 7. Register Selection
RS2
RS1
RS0
REGISTER
POWER-ON RESET STATUS
REGISTER SIZE (BITS)
0
0
0
Communications Register
0x00
8
0
0
1
Setup Register
0x01
8
0
1
0
Clock Register
0x05
8
0
1
1
Data Register
N/A
16
1
0
0
Test Register*
N/A
8
1
0
1
No Operation
—
—
1
1
0
Offset Register
0x1F 40 00
24
1
1
1
Gain Register
0x57 61 AB
24
*The test register is used for factory testing only.
Table 8. Channel Selection
CH1
CH0
AIN+
AIN-
OFFSET/GAIN
REGISTER PAIR
0
0
AIN1+
AIN1-
0
0
1
AIN2+
AIN2-
1
1
0
AIN1-
AIN1-
0
1
1
AIN1-
AIN2-
2
Table 9. Setup Register
FIRST BIT (MSB)
FUNCTION
Name
Defaults
MODE CONTROL
(LSB)
PGA GAIN CONTROL
BIPOLAR/UNIPOLAR
MODE
BUFFER ENABLE
FSYNC
MD1
MD0
G2
G1
G0
B/U
BUF
FSYNC
0
0
0
0
0
0
0
1
ZERO: (Default = 0) Zero Bit. This is a read-only bit.
Values written to this bit are ignored.
CLKDIS: (Default = 0) Clock-Disable Bit. Set CLKDIS =
1 to disable the clock when using a crystal or resonator
across CLKIN and CLKOUT. Set CLKDIS = 1 to disable
CLKOUT when using a CMOS clock source at CLKIN.
CLKOUT is held low during clock disable to save
power. Set CLKDIS = 0 to allow other devices to use
the output signal on CLKOUT as a clock source and/or
to enable the external oscillator.
CLKDIV: (Default = 0) Clock-Divider Control Bit. The
MX7705 has an internal clock divider. Set this bit to 1 to
divide the input clock by two. When this bit is set to 0, the
MX7705 operates at the external oscillator frequency.
CLK: (Default = 1) Clock Bit. Set CLK = 1 for fCLKIN =
2.4576MHz with CLKDIV = 0, or 4.9152MHz with
CLKDIV = 1.
______________________________________________________________________________________
23
MX7705
Table 6. Communications Register
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Table 10. Operating-Mode Selection
MD1
MD0
0
0
Normal Mode. Use this mode to perform normal conversions on the selected analog input channel.
1
Self-Calibration Mode. This mode performs self-calibration on the selected channel determined from CH0 and
CH1 selection bits in the communications register (Table 6). Upon completion of self-calibration, the device
returns to normal mode with MD0, MD1 returning to 0, 0. The DRDY output bit goes high when self-calibration is
requested and returns low when the calibration is complete and a new data word is in the data register. Selfcalibration performs an internal zero-scale and full-scale calibration. The analog inputs of the device are shorted
together internally during zero-scale calibration and connected to an internally generated (VREF / selected gain)
voltage during full-scale calibration. The offset and gain registers for the selected channel are automatically
updated with the calibration data.
0
Zero-Scale System-Calibration Mode. This mode performs zero-scale calibration on the selected channel
determined from CH0 and CH1 selection bits in the communications register (Table 6). The DRDY output bit
goes high when calibration is requested and returns low when the calibration is complete and a new data word
is in the data register. Performing zero-scale calibration compensates for any DC offset voltage present in the
ADC and system. Ensure that the analog input voltage is stable within 1/2 LSB for the duration of the calibration
sequence. The offset register for the selected channel is updated with the zero-scale system-calibration data.
Upon completion of calibration, the device returns to normal mode with MD0, MD1 returning to 0, 0.
1
Full-Scale System-Calibration Mode. This mode performs full-scale system calibration on the selected channel
determined by the CH0 and CH1 selection bits in the communications register. This calibration assigns a fullscale output code to the voltage present on the selected channel. Ensure that the analog input voltage is stable
within 1/2 LSB for the duration of the calibration sequence. The DRDY output bit goes high during calibration
and returns low when the calibration is complete and a new data word is in the data register. The gain register
for the selected channel is updated with the full-scale system-calibration data. Upon completion of calibration,
the device returns to normal mode with MD0, MD1 returning to 0, 0.
0
1
1
OPERATING MODE
Table 11. PGA Gain Selection
G2
G1
G0
PGA GAIN
0
0
0
1
0
0
1
2
0
1
0
4
0
1
1
8
1
0
0
16
1
0
1
32
1
1
0
64
1
1
1
128
Set CLK = 0 for optimal performance if the external
clock frequency is 1MHz with CLKDIV = 0 or 2MHz with
CLKDIV = 1.
FS1, FS0: (Default = 0, 1) Filter-Selection Bits. These bits
determine the output data rate and the digital-filter cutoff
frequency. See Table 13 for FS1 and FS0 settings.
Recalibrate when the filter characteristics are changed.
24
Data Register
The data register is a 16-bit register that can be read
and written. Figure 9 shows how to read conversion
results using the data register. A write to the data register is not required, but if the data register is written, the
device does not return to its normal state of waiting for
a write to the communications register until all 16 bits
have been written. The 16-bit data word written to the
data register is ignored.
The data from the data register is read through DOUT.
DOUT changes on the falling edge of SCLK and is valid
on the rising edge of SCLK. The data register format is
16-bit straight binary for unipolar mode with zero scale
equal to 0x0000, and offset binary for bipolar mode
with zero scale equal to 0x1000.
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Write to the calibration registers in normal mode only.
After writing to the calibration registers, the devices
implement the new offset and gain-register calibration
coefficients at the beginning of a new acquisition. To
ensure the results are valid, discard the first conversion
result after writing to the calibration registers.
To ensure that a conversion is not made using invalid
calibration data, drive FSYNC high prior to writing to the
calibration registers, and then release FSYNC low to initiate conversion.
Offset and Gain-Calibration Registers
The MX7705 contains one offset register and one gain
register for each input channel. Each register is 24 bits
wide and can be written and read. The offset registers
store the calibration coefficients resulting from a zeroscale calibration, and the gain registers store the calibration coefficients resulting from a full-scale
calibration. The data stored in these registers are 24-bit
straight binary values representing the offset or gain
errors associated with the selected channel. A 24-bit
read or write operation can be performed on the calibration registers for any selected channel. During a
write operation, 24 bits of data must be written to the
register, or no data is transferred.
Power-On Reset
At power-up, the serial-interface, logic, digital-filter, and
modulator circuits are reset. The registers are set to
their default values. The device returns to wait for a
write to the communications register. For accurate
measurements, perform calibration routines after
power-up. Allow time for the external reference and
oscillator to start up before starting calibration. See the
Typical Operating Characteristics for typical externaloscillator startup times.
Table 12. Clock Register
FIRST BIT (MSB)
FUNCTION
(LSB)
RESERVED
Name
CLKOUT
DISABLE
CLOCK
DIVIDER
CLOCK
SELECT
FILTER SELECT
MXID
ZERO
ZERO
CLKDIS
CLKDIV
CLK
FS1
FS0
1
0
0
0
0
1
0
1
Defaults
Table 13. Output Data Rate and Notch Frequency vs. Filter Select and CLKIN Frequency
CLKIN FREQUENCY
fCLKIN (MHz)*
CLK
FS1
FS0
OUTPUT DATA RATE
(FIRST NOTCH) (Hz)
-3dB FILTER CUTOFF**
(Hz)
1
0
0
0
20
5.24
1
0
0
1
25
6.55
1
0
1
0
100
26.20
1
0
1
1
200
52.40
2.4576
1
0
0
50
13.10
2.4576
1
0
1
60
15.70
2.4576
1
1
0
250
65.50
2.4576
1
1
1
500
131.00
*These values are given for CLKDIV = 0. External clock frequency, fCLKIN, can be two times the values in this column if CLKDIV = 1.
**The filter -3dB filter cutoff frequency = 0.262 x filter first-notch frequency.
______________________________________________________________________________________
25
MX7705
Test Register
This register is reserved for factory testing of the device.
For proper operation of the MX7705, do not change this
register from its default power-on reset values.
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Reset
Drive RESET low to reset the MX7705 to power-on reset
status. DRDY goes high and all communication to the
MX7705 is ignored while RESET is low. Upon releasing
RESET, the device must be reconfigured to begin a conversion. The device returns to waiting for a write to the
communication register after a reset has been performed.
Perform a calibration sequence following a reset for
accurate conversions.
The MX7705 clock generator continues to run when
RESET is pulled low. This allows any device running from
CLKOUT to be uninterrupted when the device is in reset.
Selecting Custom Output Data Rates and
First-Notch Frequency
The recommended frequency range of the external clock
is 400kHz to 5MHz. The output data rate and first notch
frequency are dependent on the decimation rate of the
digital filter. Table 14 shows the available decimation
rates of the digital filter. The output data rate and filter first
notch is calculated using the following formula:
output data rate =
fCLKIN
× 0.5
128 × Decimation Rate
(if CLKDIV = 1)
fCLKIN
output data rate =
128 × Decimation Rate
(if CLKDIV = 0)
Note: First-notch filter frequency = output data rate.
Table 14. Filter Select and Decimation Rate
CLK
FS1
FS0
DECIMATION RATE
0
0
0
391
0
0
1
313
0
1
0
78
0
1
1
39
1
0
0
384
1
0
1
320
1
1
0
77
1
1
1
38
Writing to the clock and setup registers after configuring
and initializing the host processor serial port sets up the
MX7705. Use self- or system calibrations to minimize offset and gain errors (see the Calibration section for more
details). Set FSYNC = 0 to begin calibration or conversion. The MX7705 performs free-running acquisitions
when FSYNC is low (see the Using FSYNC section). The
µC can poll the DRDY bit of the communications register
and read the data register when the DRDY bit returns a
0. For hardware polling, the DRDY output goes low when
the new data is valid in the data register.
The data register can be read multiple times while the
next conversion takes place.
The flow diagram in Figure 11 shows an example
sequence required to perform a conversion on channel
1 (AIN1+ / AIN1-) after a power-on reset.
Performing a Conversion
At power-on reset, the MX7705 expects a write to the
communications register. Writing to the communications register selects the acquisition channel, read/write
operation for the next register, power-down/normal
mode, and address of the following register to be
accessed. The MX7705 has six user-accessible registers, which control the function of the device and allow
the result to be read. Write to the communications register before accessing any other registers.
26
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
MX7705
POWER-ON RESET
INITIALIZE μC/μP SERIAL
PORT
WRITE TO THE COMMUNICATIONS
REGISTER. SELECT CHANNEL 1 AND SET
NEXT OPERATION AS A WRITE TO THE
CLOCK REGISTER.
(0x20)
WRITE TO THE CLOCK REGISTER. ENABLE
EXTERNAL OSCILLATOR. SELECT
OUTPUT UPDATE RATE OF 60Hz.
(0xA5)
WRITE TO THE COMMUNICATIONS
REGISTER. SELECT CHANNEL 1 AND SET
NEXT OPERATION AS A WRITE TO THE
SETUP REGISTER.
(0x10)
WRITE TO THE SETUP REGISTER. SET
SELF-CALIBRATION MODE, GAIN TO 0,
UNIPOLAR MODE, UNBUFFERED MODE.
BEGIN SELF-CALIBRATION/CONVERSION
BY CLEARING FSYNC.
(0x44)
HARDWARE POLLING
SOFTWARE POLLING
WRITE TO COMMUNICATIONS REGISTER.
SET NEXT OPERATION AS A READ FROM
THE COMMUNICATIONS REGISTER.
(0x08)
1 (DATA
NOT
READY)
POLL DRDY
OUTPUT
READ THE COMMUNICATIONS REGISTER
(8 BITS)
POLL DRDY
BIT
0 (DATA
READY)
WRITE TO THE COMMUNICATIONS
REGISTER. SET NEXT OPERATION AS A
READ FROM THE DATA REGISTER.
(0x38)
0 (DATA
READY)
1 (DATA NOT
READY)
READ THE DATA REGISTER
(16 BITS)
Figure 11. Sample Flow Diagram for Data Conversion
______________________________________________________________________________________
27
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Using FSYNC
When FSYNC = 1, the digital filter and analog modulator are in a reset state, inhibiting normal operation. Set
FSYNC = 0 to begin calibration or conversion.
When configured for normal operation (MD0 and MD1
set to 0), DRDY goes low 3 x 1/output data rate after
FSYNC goes low to indicate that the new conversion
result is ready to be read from the data register. DRDY
returns high when a read operation on the data register
is complete. As long as FSYNC remains low, the
MX7705 performs free-running conversions with the
data registers updating at the output data rate. If the
valid data is not read before the next conversion result
is ready, DRDY returns high for 500 x 1/fCLKIN before
going low again to indicate a new conversion. Set
FSYNC = 1 to stop converting data.
If FSYNC goes high while DRDY is low (indicating that
valid data has not yet been read from the data register), DRDY does not reset high. DRDY remains low until
the new data is read from the data register or until
FSYNC goes low to begin a new conversion.
Table 15 provides the duration-to-mode bits and duration-to-DRDY for each calibration sequence. Duration-tomode bits provide the time required for the calibration
sequence to complete (MD1 and MD0 return to 0).
Duration-to-DRDY provides the time until the first conversion result is valid in the data register (DRDY goes low).
The pipeline delay necessary to ensure that the first
conversion result is valid is tP (tP = 2000 x 1/fCLKIN).
When selecting self-calibration (MD1 = 0, MD0 = 1),
DRDY goes low 9 x 1/output data rate + tP after FSYNC
goes low (or after a write operation to the setup register
with MD1 = 0 and MD0 = 1 is performed while FSYNC
is already low) to indicate new data in the data register.
The pipeline delay required to ensure that the first conversion result is valid is tP (tP = 2000 x 1/fCLKIN).
When zero-scale or full-scale calibration is selected,
DRDY goes low 4 x 1/output data rate + tP after FSYNC
goes low (or while the zero-scale or full-scale calibration command is issued when FSYNC is already low) to
indicate new data in the data register (see the
Calibration section).
Calibration
To compensate for errors introduced by temperature
variations or system DC offsets, perform an on-chip calibration. Select calibration options by writing to the
MD1 and MD0 bits in the setup register (Table 9).
Calibration removes gain and offset errors from the
device and/or the system. Recalibrate with changes in
ambient temperature, supply voltage, bipolar/unipolar
mode, PGA gain, and output data rate.
The MX7705 offers two calibration modes, self-calibration and system calibration. The channels of the
MX7705 are independently calibrated (Table 8). The
calibration coefficients resulting from a calibration
sequence on a selected channel are stored in the corresponding offset and gain-register pair.
Self- and system calibration automatically calculate the
offset and gain coefficients, which are written to the offset and gain registers. These offset and gain coefficients provide offset and gain-error correction for the
specified channel.
Self-Calibration
Self-calibration compensates for offset and gain errors
internal to the ADC. Prior to calibration, set the PGA gain,
unipolar/bipolar mode, and input channel setting. During
self-calibration, AIN+ and AIN- of the selected channel
are internally shorted together. The ADC calibrates this
condition as the zero-scale output level. For bipolar
mode, this zero-scale point is the midscale of the bipolar
transfer function.
Table 15. Calibration Sequences
CALIBRATION TYPE
(MD1, MD0)
CALIBRATION SEQUENCE
DURATION-TO-MODE
BITS*
DURATION TO DRDY**
Self-calibration (0,1)
Internal zero-scale calibration at
selected gain + internal full-scale
calibration at selected gain
6 x 1/output data rate
9 x 1/output data rate + tP
Zero-scale system calibration (1,0)
Zero-scale calibration on AIN at
selected gain
3 x 1/output data rate
4 x 1/output data rate + tP
Full-scale system calibration (1,1)
Full-scale calibration on AIN at
selected gain
3 x 1/output data rate
4 x 1/output data rate + tP
*Duration-to-mode bits represents the completion of the calibration sequence.
**Duration to DRDY represents the time at which a new conversion result is available in the data register.
28
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
The DRDY output goes high at the start of calibration
and falls low when the calibration is complete and the
next conversion result is valid in the data register. The
total time for self-calibration and one conversion (time
until DRDY goes low) is 9 x 1/output data rate. If DRDY
is low before or goes low during the calibration command write to the setup register, DRDY takes up to one
additional modulator cycle (128/fCLKIN) to return high to
indicate a calibration or conversion in progress.
System Calibration
System calibration compensates for offset and gain
errors for the entire analog signal path including the
ADC, signal conditioning, and signal source. System
calibration is a two-step process and requires individual zero-scale and full-scale calibrations on the selected channel at a specified PGA gain. Recalibration is
recommended with changes in ambient temperature,
supply voltage, bipolar/unipolar mode, PGA gain, and
output data rate. Before starting calibration, set the
PGA gain and the desired channel.
Set the zero-scale reference point across AIN+ and AIN-.
Start the zero-scale calibration by setting MD1 = 1, MD0
= 0, and FSYNC = 0 in the setup register. When zeroscale calibration is complete (3 x 1/output data rate),
MD1 and MD0 both return to zero. DRDY goes high at the
start of the zero-scale system calibration and returns low
when there is a valid word in the data register (4 x 1/output data rate). The time until DRDY goes low is comprised of one zero-scale calibration sequence (3 x
1/output data rate) and one conversion on the AIN voltage (1 x 1/output data rate). If DRDY is low before or
goes low during the calibration command write to the
setup register, DRDY takes up to one additional modulator cycle (128/fCLKIN) to return high to indicate a calibration or conversion in progress.
After performing a zero-scale calibration, connect the
analog inputs to the full-scale voltage level (V REF /
GAIN). Perform a full-scale calibration by setting MD1 =
1 and MD0 = 1. After 3 x 1/output data rate, MD1 and
MD0 both return to zero at the completion of full-scale
calibration. DRDY goes high at the beginning of calibration and returns low after calibration is complete
and new data is in the data register (4 x 1/output data
rate). The time until DRDY goes low is comprised of
one full-scale calibration sequence (3 x 1/output data
rate) and one conversion on the AIN voltage (1 x 1/output data rate). If DRDY is low before or goes low during
the calibration-command write to the setup register,
DRDY takes up to one additional modulator cycle
(128/fCLKIN) to return high to indicate a calibration or
conversion in progress.
In bipolar mode, the midpoint (zero scale) and positive
full scale of the transfer function are used to calculate the
calibration coefficients of the gain and offset registers. In
unipolar mode, system calibration is performed using the
two endpoints of the transfer function (Figures 4 and 5).
Power-Down Modes
The MX7705 includes a power-down mode to save
power. Select power-down mode by setting PD = 1 in
the communications register. The PD bit does not affect
the serial interface or the status of the DRDY line. While
in power-down mode, the MX7705 retains the contents
of all of its registers. Placing the part in power-down
mode reduces current consumption to 2µA (typ) when
in external clock mode and with CLKIN connected to
VDD or GND. If DRDY is high before the part enters
power-down mode, then DRDY remains high until the
part returns to normal operation mode and new data is
available in the data register. If DRDY is low before the
part enters power-down mode, indicating new data in
the data register, the data register can be read during
power-down mode. DRDY goes high at the end of this
read operation. If the new data remains unread, DRDY
stays low until the MX7705 is taken out of power-down
mode and resumes data conversion. Resume normal
operation by setting PD = 0. The device begins a new
conversion with a result appearing in 3 x 1/output data
rate + tP, where tP = 2000 x 1/fCLKIN, after PD is set to
0. If the clock is stopped during power-down mode,
allow sufficient time for the clock to start up before
resuming conversion.
If CLKDIS = 0, CLKOUT remains active during powerdown mode to provide a clock source for other devices
in the system.
______________________________________________________________________________________
29
MX7705
Next, an internally generated voltage (VREF / GAIN) is
applied across AIN+ and AIN-. This condition results in
the full-scale calibration.
Start self-calibration by setting MD1 = 0, MD0 = 1, and
FSYNC = 0 in the setup register. Self-calibration completes in 6 x 1/output data rate. The MD1 and MD0 bits
both return to zero at the end of calibration. The device
returns to normal acquisition mode and performs a conversion, which completes in 3 x 1/output data rate after
the self-calibration sequence.
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Applications Information
VDD
Applications Examples
Strain-Gauge Measurement
Connect the differential inputs of the MX7705 to the
bridge network of the strain gauge. In Figure 12, the analog positive supply voltage powers the bridge network
and the MX7705, along with the reference voltage in a
ratiometric configuration. The on-chip PGA allows the
MX7705 to handle an analog input voltage range as low
as 20mV to full scale.
Temperature Measurement
Use the MX7705 for temperature measurements from a
thermocouple (Figure 13). Operate the MX7705 in
buffered mode to allow large decoupling capacitors at
the analog inputs. The decoupling capacitors eliminate
any noise pickup from the thermocouple leads. AIN1- is
biased up at the reference voltage to accommodate the
reduced common-mode input range in buffered mode.
Optical Isolation
For applications that require an optically isolated interface, see Figure 14. With 6N136-type optocouplers,
maximum clock speed is 4MHz. Maximum clock speed
is limited by the degree of mismatch between the individual optocouplers. Faster optocouplers allow faster
signaling at a higher cost.
Layout, Grounding, Bypassing
Use PC boards with separate analog and digital
ground planes. Connect the two ground planes together at the MX7705 GND. Isolate the digital supply from
the analog with a low-value resistor (10Ω) or ferrite
bead when the analog and digital supplies come from
the same source.
Ensure that digital return currents do not pass through
the analog ground and that return-current paths are low
impedance. A 5mA current flowing through a PC board
ground trace impedance of only 0.05Ω creates an error
voltage of about 250µV.
Layout the PC board to ensure digital and analog signal lines are kept separate. Do not run digital lines
(especially the SCLK and DOUT) parallel to any analog
lines. If they must cross another, do so at right angles.
Bypass VDD to the analog ground plane with a 0.1µF
capacitor in parallel with a 1µF to 10µF low-ESR capacitor. Keep capacitor leads short for best supply-noise
rejection. Bypass REF+ and REF- with a 0.1µF capacitor to GND. Place all bypass capacitors as close to the
device as possible to achieve the best decoupling.
10μF
0.1μF
REF+
RREF
CLKIN
VDD
0.1μF
CLKOUT
REF0.1μF
ACTIVE
GAUGE
CS
MX7705
R
SCLK
DIN
AIN1+
AIN1DUMMY
GAUGE
DOUT
DRDY
R
RESET
GND
Figure 12. Strain-Gauge Measurement
VDD = 3V/5V*
10μF
10μF
VDD
AIN1+
THERMOCOUPLE
JUNCTION
CLKOUT
AIN1-
MX7705
CS
SCLK
1.225V/2.5V
REFERENCE*
REF+
DIN
0.1μF
DOUT
DRDY
REF0.1μF
GND
RESET
*USE A 1.225V REFERENCE FOR VDD = 3V OR A 2.5V REFERENCE FOR VDD = 5V.
Figure 13. Temperature Measurement
30
CLKIN
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
ISO
3V/5V
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line is either a best-straight-line fit or a line
drawn between the endpoints of the transfer function,
once offset and gain errors have been nullified. INL for
the MX7705 is measured using the endpoint method.
This is the more conservative method.
MX7705
Definitions
VCC
VDD
2kΩ
VCC
DIN
6N136
100Ω
MOSI
MX7705
Unipolar Offset Error
For an ideal converter, the first transition occurs at 0.5
LSB above zero. Offset error is the amount of deviation
between the measured first transition point and the
ideal point.
Bipolar Zero Error
2kΩ
VCC
SCLK
6N136
100Ω
SCK
In bipolar mode, the ideal midscale transition occurs at
AIN+ - AIN- = 0. Bipolar zero error is the measured
deviation from this ideal value.
VCC
2kΩ
Gain Error
With a full-scale analog input voltage applied to the
ADC (resulting in all ones in the digital code), gain error
is defined as the amount of deviation between the ideal
transfer function and the measured transfer function
(with the offset error or bipolar zero error removed).
Gain error is usually expressed in LSB or a percent of
full-scale range (%FSR).
MISO
6N136
DOUT
100Ω
CS
CS
Positive Full-Scale Error
For the ideal transfer curve, the code edge transition
that causes a full-scale transition to occur is 1.5 LSB
below full scale. The positive full-scale error is the difference between this code transition of the ideal transfer function and the actual measured value at this code
transition. Unlike gain error, unipolar offset error and
bipolar zero error are included in the positive full-scale
error measurement.
Bipolar Negative Full-Scale Error
For the ideal transfer curve, the code edge transition that
causes a negative full-scale transition to occur is 0.5 LSB
above negative full scale. The negative full-scale error is
the difference between this code transition of the ideal
transfer function and the actual measured value at this
code transition.
Figure 14. Optically Isolated Interface
both input terminals. The common-mode signal can be
either an AC or a DC signal or a combination of the two.
CMR is often expressed in decibels. Common-mode
rejection ratio (CMRR) is the ratio of the differential signal gain to the common-mode signal gain.
Power-Supply Rejection Ratio
Power-supply rejection ratio (PSRR) is the ratio of the
input signal change (V) to the change in the converter
output (V). It is typically measured in decibels.
Input Common-Mode Rejection
Input common-mode rejection (CMR) is the ability of a
device to reject a signal that is common to or applied to
______________________________________________________________________________________
31
MX7705
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
Package Information
Chip Information
TRANSISTOR COUNT: 42,000
PROCESS: BiCMOS
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages.
PACKAGE TYPE
32
PACKAGE CODE
DOCUMENT NO.
16 PDIP
P16-1
21-0043
16 WIDE SO
W16-1
21-0042
16 TSSOP
U16-2
21-0066
______________________________________________________________________________________
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
REVISION
NUMBER
REVISION
DATE
3
6/09
DESCRIPTION
PAGES
CHANGED
Corrected values in Reference section
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 33
© 2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products.
MX7705
Revision History