ONSEMI MC34166T

MC34166, MC33166
3.0 A, Step-Up/Down/
Inverting Switching
Regulators
The MC34166, MC33166 series are high performance fixed
frequency power switching regulators that contain the primary
functions required for dc–to–dc converters. This series was
specifically designed to be incorporated in step–down and
voltage–inverting configurations with a minimum number of external
components and can also be used cost effectively in step–up
applications.
These devices consist of an internal temperature compensated
reference, fixed frequency oscillator with on–chip timing components,
latching pulse width modulator for single pulse metering, high gain
error amplifier, and a high current output switch.
Protective features consist of cycle–by–cycle current limiting,
undervoltage lockout, and thermal shutdown. Also included is a low
power standby mode that reduces power supply current to 36 µA.
• Output Switch Current in Excess of 3.0 A
• Fixed Frequency Oscillator (72 kHz) with On–Chip Timing
• Provides 5.05 V Output without External Resistor Divider
• Precision 2% Reference
• 0% to 95% Output Duty Cycle
• Cycle–by–Cycle Current Limiting
• Undervoltage Lockout with Hysteresis
• Internal Thermal Shutdown
• Operation from 7.5 V to 40 V
• Standby Mode Reduces Power Supply Current to 36 µA
• Economical 5–Lead TO–220 Package with Two Optional Leadforms
• Also Available in Surface Mount D2PAK Package
• Moisture Sensitivity Level (MSL) Equals 1
http://onsemi.com
x
A
WL
Y
WW
= 3 or 4
= Assembly Location
= Wafer Lot
= Year
= Work Week
TO–220
TH SUFFIX
CASE 314A
MARKING
DIAGRAMS
MC
3x166T
AWLYWW
1
5
TO–220
TV SUFFIX
CASE 314B
1
MC
3x166T
AWLYWW
5
Heatsink surface connected to Pin 3
Vin
MC
3x166T
AWLYWW
TO–220
T SUFFIX
CASE 314D
4
ILIMIT
1
Oscillator
S
Q
5
2
R
Pin
PWM
UVLO
Thermal
L
1.
2.
3.
4.
5.
Voltage Feedback Input
Switch Output
Ground
Input Voltage/VCC
Compensation/Standby
Reference
EA
1
VO
5.05 V/
3.0 A
3
5
D2PAK
D2T SUFFIX
CASE 936A
1
5
Heatsink surface (shown as
terminal 6 in case outline
drawing) is connected to Pin 3
MC
3x166T
AWLYWW
1
5
This device contains 143 active transistors.
ORDERING INFORMATION
Figure 1. Simplified Block Diagram
(Step Down Application)
 Semiconductor Components Industries, LLC, 2002
January, 2002 – Rev. 6
See detailed ordering and shipping information in the package
dimensions section on page 17 of this data sheet.
1
Publication Order Number:
MC34166/D
MC34166, MC33166
MAXIMUM RATINGS (Note 2)
Symbol
Rating
Power Supply Input Voltage
Value
Unit
VCC
40
V
VO(switch)
–1.5 to + Vin
V
VFB, VComp
–1.0 to + 7.0
V
Power Dissipation
Case 314A, 314B and 314D (TA = +25°C)
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
Case 936A (D2PAK) (TA = +25°C)
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
PD
θJA
θJC
PD
θJA
θJC
Internally Limited
65
5.0
Internally Limited
70
5.0
W
°C/W
°C/W
W
°C/W
°C/W
Operating Junction Temperature
TJ
+150
°C
Operating Ambient Temperature (Note 3)
MC34166
MC33166
TA
Storage Temperature Range
Tstg
Switch Output Voltage Range
Voltage Feedback and Compensation Input Voltage Range
°C
0 to + 70
– 40 to + 85
1. Maximum package power dissipation limits must be observed to prevent thermal shutdown activation.
2. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL–STD–883, Method 3015.
Machine Model Method 200 V.
Thigh = + 70°C for MC34166
3. Tlow = 0°C for MC34166
= – 40°C for MC33166
= + 85°C for MC33166
http://onsemi.com
2
– 65 to +150
°C
MC34166, MC33166
ELECTRICAL CHARACTERISTICS (VCC = 12 V, for typical values TA = +25°C, for min/max values TA is the operating ambient
temperature range that applies [Notes 4, 5], unless otherwise noted.)
Symbol
Min
Typ
Max
Unit
TA = +25°C
TA = Tlow to Thigh
fOSC
65
62
72
–
79
81
kHz
TA = +25°C
TA = Tlow to Thigh
VFB(th)
4.95
4.85
5.05
–
5.15
5.2
V
Regline
–
0.03
0.078
%/V
Characteristic
OSCILLATOR
Frequency (VCC = 7.5 V to 40 V)
ERROR AMPLIFIER
Voltage Feedback Input Threshold
Line Regulation (VCC = 7.5 V to 40 V, TA = +25°C)
IIB
–
0.15
1.0
µA
PSRR
60
80
–
dB
VOH
VOL
4.2
–
4.9
1.6
–
1.9
DC(max)
DC(min)
92
0
95
0
100
0
Vsat
–
(VCC
–1.5)
(VCC
–1.8)
V
Isw(off)
–
0
100
µA
Ipk(switch)
3.3
4.3
6.0
Input Bias Current (VFB = VFB(th) + 0.15 V)
Power Supply Rejection Ratio (VCC = 10 V to 20 V, f = 120 Hz)
Output Voltage Swing
High State (ISource = 75 µA, VFB = 4.5 V)
Low State (ISink = 0.4 mA, VFB = 5.5 V)
V
PWM COMPARATOR
Duty Cycle
Maximum (VFB = 0 V)
Minimum (VComp = 1.9 V)
%
SWITCH OUTPUT
Output Voltage Source Saturation (VCC = 7.5 V, ISource = 3.0 A)
Off–State Leakage (VCC = 40 V, Pin 2 = Gnd)
Current Limit Threshold
Switching Times (VCC = 40 V, Ipk = 3.0 A, L = 375 µH, TA = +25°C)
Output Voltage Rise Time
Output Voltage Fall Time
A
ns
tr
tf
–
–
100
50
200
100
Startup Threshold (VCC Increasing, TA = +25°C)
Vth(UVLO)
5.5
5.9
6.3
V
Hysteresis (VCC Decreasing, TA = +25°C)
VH(UVLO)
0.6
0.9
1.2
V
–
–
36
31
100
55
µA
mA
UNDERVOLTAGE LOCKOUT
TOTAL DEVICE
Power Supply Current (TA = +25°C )
Standby (VCC = 12 V, VComp < 0.15 V)
Operating (VCC = 40 V, Pin 1 = Gnd for maximum duty cycle)
ICC
4. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
5. Tlow = 0°C for MC34166
Thigh = + 70°C for MC34166
= – 40°C for MC33166
= + 85°C for MC33166
http://onsemi.com
3
MC34166, MC33166
100
VCC = 12 V
VFB(th) Max = 5.15 V
5.17
5.09
IIB, INPUT BIAS CURRENT (nA)
V FB(th), VOLTAGE FEEDBACK INPUT THRESHOLD (V)
5.25
VFB(th) Typ = 5.05 V
5.01
VFB(th) Min = 4.95 V
4.93
4.85
-55
-25
0
25
50
75
TA, AMBIENT TEMPERATURE (°C)
100
VCC = 12 V
VFB = VFB(th)
80
60
40
20
0
-55
125
80
Gain
60
VCC = 12 V
VComp = 3.25 V
RL = 100 k
TA = +25°C
40
0
30
60
90
Phase
φ, EXCESS PHASE (DEGREES)
A VOL, OPEN LOOP VOLTAGE GAIN (dB)
100
20
120
0
150
-20
10
100
1.0 k
10 k
100 k
f, FREQUENCY (Hz)
180
10 M
1.0 M
DC, SWITCH OUTPUT DUTY CYCLE (%)
∆ f OSC , OSCILLATOR FREQUENCY CHANGE (%)
VCC = 12 V
-4.0
-8.0
-25
0
25
50
75
100
TA, AMBIENT TEMPERATURE (°C)
125
1.6
1.2
0.8
VCC = 12 V
VFB = 5.5 V
TA = +25°C
0.4
0
0
0.4
0.8
1.2
1.6
ISink, OUTPUT SINK CURRENT (mA)
2.0
Figure 5. Error Amp Output Saturation
versus Sink Current
4.0
-12
-55
100
2.0
Figure 4. Error Amp Open Loop Gain and
Phase versus Frequency
0
0
25
50
75
TA, AMBIENT TEMPERATURE (°C)
Figure 3. Voltage Feedback Input Bias
Current versus Temperature
Vsat , OUTPUT SATURATION VOLTAGE (V)
Figure 2. Voltage Feedback Input Threshold
versus Temperature
-25
125
100
80
VCC = 12 V
TA = +25°C
60
40
20
0
1.5
Figure 6. Oscillator Frequency Change
versus Temperature
2.0
2.5
3.0
3.5
4.0
VComp, COMPENSATION VOLTAGE (V)
Figure 7. Switch Output Duty Cycle
versus Compensation Voltage
http://onsemi.com
4
4.5
0
0
VCC
-0.5
Vsw, SWITCH OUTPUT VOLTAGE (V)
Vsat , SWITCH OUTPUT SOURCE SATURATION (V)
MC34166, MC33166
TA = +25°C
-1.0
-1.5
-2.0
-2.5
-3.0
0
1.0
2.0
3.0
4.0
ISource, SWITCH OUTPUT SOURCE CURRENT (A)
VCC = 12 V
Pin 5 = 2.0 V
Pins 1, 3 = Gnd
Pin 2 Driven Negative
-0.2
-0.4
Isw = 100 µA
-0.6
-0.8
Isw = 10 mA
-1.0
-1.2
-55
5.0
VCC = 12 V
Pins 1, 2, 3 = Gnd
100
125
4.5
4.3
4.1
-25
0
25
50
75
TA, AMBIENT TEMPERATURE (°C)
100
Pin 4 = VCC
Pins 1, 3, 5 = Gnd
Pin 2 Open
TA = +25°C
120
80
40
0
0
125
Figure 10. Switch Output Current Limit
Threshold versus Temperature
10
20
30
VCC, SUPPLY VOLTAGE (V)
40
Figure 11. Standby Supply Current
versus Supply Voltage
6.5
40
Startup Threshold
VCC Increasing
6.0
I CC, SUPPLY CURRENT (mA)
Vth(UVLO) , UNDERVOLTAGE LOCKOUT THRESHOLD (V)
0
25
50
75
TA, AMBIENT TEMPERATURE (°C)
160
4.7
5.5
Turn-Off Threshold
VCC Decreasing
5.0
4.5
4.0
-55
-25
Figure 9. Negative Switch Output Voltage
versus Temperature
I CC, SUPPLY CURRENT ( µ A)
I pk(switch) , CURRENT LIMIT THRESHOLD (A)
Figure 8. Switch Output Source Saturation
versus Source Current
3.9
-55
Gnd
-25
0
25
50
75
TA, AMBIENT TEMPERATURE (°C)
100
30
20
0
125
Pin 4 = VCC
Pins 1, 3 = Gnd
Pins 2, 5 Open
TA = +25°C
10
0
Figure 12. Undervoltage Lockout
Threshold versus Temperature
10
20
30
VCC, SUPPLY VOLTAGE (V)
Figure 13. Operating Supply Current
versus Supply Voltage
http://onsemi.com
5
40
MC34166, MC33166
Vin
Current
Sense
+
S
Switch
Output
Q
R
Pulse Width
Modulator
L
5.05 V
Reference
+
+
Error
Amp
100 µA
Compensation
5
Voltage
Feedback
Input
1
120
3
2
Undervoltage
Lockout
PWM Latch
Thermal
Shutdown
Gnd
Input Voltage/VCC
Cin
Oscillator
CT
4
CF
RF
= Sink Only
Positive True Logic
Figure 14. MC34166 Representative Block Diagram
4.1 V
Timing Capacitor CT
Compensation
2.3 V
ON
Switch Output
OFF
Figure 15. Timing Diagram
http://onsemi.com
6
R2
R1
CO
VO
MC34166, MC33166
INTRODUCTION
at 4.3 A. Figure 10 illustrates switch output current limit
threshold versus temperature.
The MC34166, MC33166 series are monolithic power
switching regulators that are optimized for dc–to–dc
converter applications. These devices operate as fixed
frequency, voltage mode regulators containing all the active
functions required to directly implement step–down and
voltage–inverting converters with a minimum number of
external components. They can also be used cost effectively
in step–up converter applications. Potential markets include
automotive, computer, industrial, and cost sensitive
consumer products. A description of each section of the
device is given below with the representative block diagram
shown in Figure 14.
Error Amplifier and Reference
A high gain Error Amplifier is provided with access to the
inverting input and output. This amplifier features a typical
dc voltage gain of 80 dB, and a unity gain bandwidth of
600 kHz with 70 degrees of phase margin (Figure 4). The
noninverting input is biased to the internal 5.05 V reference
and is not pinned out. The reference has an accuracy of
± 2.0% at room temperature. To provide 5.0 V at the load,
the reference is programmed 50 mV above 5.0 V to
compensate for a 1.0% voltage drop in the cable and
connector from the converter output. If the converter design
requires an output voltage greater than 5.05 V, resistor R1
must be added to form a divider network at the feedback
input as shown in Figures 14 and 19. The equation for
determining the output voltage with the divider network is:
Oscillator
The oscillator frequency is internally programmed to
72 kHz by capacitor CT and a trimmed current source. The
charge to discharge ratio is controlled to yield a 95%
maximum duty cycle at the Switch Output. During the
discharge of CT, the oscillator generates an internal blanking
pulse that holds the inverting input of the AND gate high,
disabling the output switch transistor. The nominal
oscillator peak and valley thresholds are 4.1 V and 2.3 V
respectively.
Vout 5.05
RR2 1
1
External loop compensation is required for converter
stability. A simple low–pass filter is formed by connecting
a resistor (R2) from the regulated output to the inverting
input, and a series resistor–capacitor (RF, CF) between Pins
1 and 5. The compensation network component values
shown in each of the applications circuits were selected to
provide stability over the tested operating conditions. The
step–down converter (Figure 19) is the easiest to
compensate for stability. The step–up (Figure 21) and
voltage–inverting (Figure 23) configurations operate as
continuous conduction flyback converters, and are more
difficult to compensate. The simplest way to optimize the
compensation network is to observe the response of the
output voltage to a step load change, while adjusting RF and
CF for critical damping. The final circuit should be verified
for stability under four boundary conditions. These
conditions are minimum and maximum input voltages, with
minimum and maximum loads.
By clamping the voltage on the error amplifier output
(Pin 5) to less than 150 mV, the internal circuitry will be
placed into a low power standby mode, reducing the power
supply current to 36 µA with a 12 V supply voltage.
Figure 11 illustrates the standby supply current versus
supply voltage.
The Error Amplifier output has a 100 µA current source
pull–up that can be used to implement soft–start. Figure 18
shows the current source charging capacitor CSS through a
series diode. The diode disconnects CSS from the feedback
loop when the 1.0 M resistor charges it above the operating
range of Pin 5.
Pulse Width Modulator
The Pulse Width Modulator consists of a comparator with
the oscillator ramp voltage applied to the noninverting input,
while the error amplifier output is applied into the inverting
input. Output switch conduction is initiated when CT is
discharged to the oscillator valley voltage. As CT charges to
a voltage that exceeds the error amplifier output, the latch
resets, terminating output transistor conduction for the
duration of the oscillator ramp–up period. This PWM/Latch
combination prevents multiple output pulses during a given
oscillator clock cycle. Figures 7 and 15 illustrate the switch
output duty cycle versus the compensation voltage.
Current Sense
The MC34166 series utilizes cycle–by–cycle current
limiting as a means of protecting the output switch transistor
from overstress. Each on–cycle is treated as a separate
situation. Current limiting is implemented by monitoring the
output switch transistor current buildup during conduction,
and upon sensing an overcurrent condition, immediately
turning off the switch for the duration of the oscillator
ramp–up period.
The collector current is converted to a voltage by an
internal trimmed resistor and compared against a
reference by the Current Sense comparator. When the
current limit threshold is reached, the comparator resets
the PWM latch. The current limit threshold is typically set
http://onsemi.com
7
MC34166, MC33166
Switch Output
functional before the output stage is enabled. The internal
5.05 V reference is monitored by the comparator which
enables the output stage when VCC exceeds 5.9 V. To
prevent erratic output switching as the threshold is crossed,
0.9 V of hysteresis is provided.
The output transistor is designed to switch a maximum
of 40 V, with a minimum peak collector current of 3.3 A.
When configured for step–down or voltage–inverting
applications, as in Figures 19 and 23, the inductor will
forward bias the output rectifier when the switch turns off.
Rectifiers with a high forward voltage drop or long turn–on
delay time should not be used. If the emitter is allowed to
go sufficiently negative, collector current will flow,
causing additional device heating and reduced conversion
efficiency. Figure 9 shows that by clamping the emitter to
0.5 V, the collector current will be in the range of 100 µA
over temperature. A 1N5822 or equivalent Schottky barrier
rectifier is recommended to fulfill these requirements.
Thermal Protection
Internal Thermal Shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated, typically at 170°C,
the latch is forced into a ‘reset’ state, disabling the output
switch. This feature is provided to prevent catastrophic
failures from accidental device overheating. It is not
intended to be used as a substitute for proper heatsinking.
The MC34166 is contained in a 5–lead TO–220 type package.
The tab of the package is common with the center pin (Pin 3)
and is normally connected to ground.
Undervoltage Lockout
An Undervoltage Lockout comparator has been
incorporated to guarantee that the integrated circuit is fully
DESIGN CONSIDERATIONS
tight component layout is recommended. Capacitors CIN,
CO, and all feedback components should be placed as close
to the IC as physically possible. It is also imperative that the
Schottky diode connected to the Switch Output be located as
close to the IC as possible.
Do not attempt to construct a converter on wire–wrap
or plug–in prototype boards. Special care should be taken
to separate ground paths from signal currents and ground
paths from load currents. All high current loops should be
kept as short as possible using heavy copper runs to
minimize ringing and radiated EMI. For best operation, a
http://onsemi.com
8
MC34166, MC33166
+
Error
Amp
100 µA
+
Error
Amp
100 µA
120
1
120
Compensation
Compensation
1
5
R1
5
R1
I = Standby Mode
VShutdown = VZener + 0.7
Figure 17. Over Voltage Shutdown Circuit
Figure 16. Low Power Standby Circuit
+
Error
Amp
100 µA
1
120
Compensation
D2
Vin
1.0 M
5
R1
D1
Css
tSoft-Start ≈ 35,000 Css
Figure 18. Soft–Start Circuit
http://onsemi.com
9
MC34166, MC33166
Vin
12 V
+
4
ILIMIT
+
Oscillator
Cin
330
S
Q1
Q
R
2
PWM
D1
1N5822
UVLO
L
190 µH
Thermal
Reference
+
+
EA
R2
1
5
3
Test
CF
RF
0.1
68 k
CO
2200
6.8 k
+
VO
5.05 V/3.0 A
R1
Conditions
Results
Line Regulation
Vin = 8.0 V to 36 V, IO = 3.0 A
5.0 mV = ± 0.05%
Load Regulation
Vin = 12 V, IO = 0.25 A to 3.0 A
2.0 mV = ± 0.02%
Output Ripple
Vin = 12 V, IO = 3.0 A
10 mVpp
Short Circuit Current
Vin = 12 V, RL = 0.1 Ω
4.3 A
Efficiency
Vin = 12 V, IO = 3.0 A
82.8%
L = Coilcraft M1496–A or General Magnetics Technology GMT–0223, 42 turns of #16 AWG
on Magnetics Inc. 58350–A2 core. Heatsink = AAVID Engineering Inc. 5903B, or 5930B.
The Step–Down Converter application is shown in Figure 19. The output switch transistor Q1 interrupts the input voltage, generating a
squarewave at the LCO filter input. The filter averages the squarewaves, producing a dc output voltage that can be set to any level between
Vin and Vref by controlling the percent conduction time of Q1 to that of the total oscillator cycle time. If the converter design requires an output
voltage greater than 5.05 V, resistor R1 must be added to form a divider network at the feedback input.
Figure 19. Step–Down Converter
+
-
+
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉ
ÉÉÉÉÉ
+
R2
-
VO
CO
Vin
1.9 ″
+
(Bottom View)
R1
L
CF
D1
RF
Cin
MC34166 STEP–DOWN
3.0″
(Top View)
Figure 20. Step–Down Converter Printed Circuit Board and Component Layout
http://onsemi.com
10
MC34166, MC33166
Vin
12 V
+
4
ILIMIT
+
Oscillator
Cin
330
S
D1
1N5822
Q1
Q
R
2
PWM
L
190 µH
UVLO
*RG
620
D4
1N4148
Thermal
Q2
MTP3055EL
Reference
+
D3
1N967A
+
EA
1
5
3
D2
1N5822
R2
CF
RF
0.47
4.7 k
CO
1000
6.8 k
VO
28 V/0.6 A
+
R1
1.5 k
*Gate resistor RG, zener diode D3, and diode D4 are required only when Vin is greater than 20 V.
Test
Conditions
Results
Line Regulation
Vin = 8.0 V to 24 V, IO = 0.6 A
23 mV = ± 0.41%
Load Regulation
Vin = 12 V, IO = 0.1 A to 0.6 A
3.0 mV = ± 0.005%
Output Ripple
Vin = 12 V, IO = 0.6 A
100 mVpp
Short Circuit Current
Vin = 12 V, RL = 0.1 Ω
4.0 A
Efficiency
Vin = 12 V, IO = 0.6 A
82.8%
L = Coilcraft M1496–A or General Magnetics Technology GMT–0223, 42 turns of #16 AWG
on Magnetics Inc. 58350–A2 core.
Heatsink = AAVID Engineering Inc. MC34166: 5903B, or 5930B MTP3055EL: 5925B
Figure 21 shows that the MC34166 can be configured as a step–up/down converter with the addition of an external power MOSFET. Energy
is stored in the inductor during the on–time of transistors Q1 and Q2. During the off–time, the energy is transferred, with respect to ground, to
the output filter capacitor and load. This circuit configuration has two significant advantages over the basic step–up converter circuit. The first
advantage is that output short–circuit protection is provided by the MC34166, since Q1 is directly in series with Vin and the load. Second, the
output voltage can be programmed to be less than Vin. Notice that during the off–time, the inductor forward biases diodes D1 and D2, transferring
its energy with respect to ground rather than with respect to Vin. When operating with Vin greater than 20 V, a gate protection network is required
for the MOSFET. The network consists of components RG, D3, and D4.
Figure 21. Step–Up/Down Converter
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
+
CO
+
(Bottom View)
CF
R1
+
D1
Cin
RF
D2
(Top View)
Figure 22. Step–Up/Down Converter Printed Circuit Board and Component Layout
http://onsemi.com
11
ÎÎ
Î
ÎÎ
Î
ÎÎ
Î
ÎÎ
ÎÎ
Q2
-
-
D3
R2
Vin
VO
L
+
1.9″
MC34166 STEP–UP/DOWN
3.45″
RG
MC34166, MC33166
Vin
12 V
+
4
ILIMIT
+
Oscillator
Cin
330
S
Q1
Q
R
2
PWM
L
190 µH
UVLO
D1
1N5822
Thermal
Reference
+
+
EA
R1
1
Test
CF
RF
0.47
4.7 k
+
5
3
2.4 k
C1
R2
3.3 k
Conditions
VO
-12 V/1.0 A
CO
2200
0.047
Results
Line Regulation
Vin = 8.0 V to 24 V, IO = 1.0 A
3.0 mV = ± 0.01%
Load Regulation
Vin = 12 V, IO = 0.1 A to 1.0 A
4.0 mV = ± 0.017%
Output Ripple
Vin = 12 V, IO = 1.0 A
80 mVpp
Short Circuit Current
Vin = 12 V, RL = 0.1 Ω
3.74 A
Efficiency
Vin = 12 V, IO = 1.0 A
81.2%
L = Coilcraft M1496–A or General Magnetics Technology GMT–0223, 42 turns of #16 AWG
on Magnetics Inc. 58350–A2 core. Heatsink = AAVID Engineering Inc. 5903B, or 5930B.
Two potential problems arise when designing the standard voltage–inverting converter with the MC34166. First, the Switch Output emitter is
limited to –1.5 V with respect to the ground pin and second, the Error Amplifier’s noninverting input is internally committed to the reference and
is not pinned out. Both of these problems are resolved by connecting the IC ground pin to the converter’s negative output as shown in Figure 23.
This keeps the emitter of Q1 positive with respect to the ground pin and has the effect of reversing the Error Amplifier inputs. Note that the voltage
drop across R1 is equal to 5.05 V when the output is in regulation.
Figure 23. Voltage–Inverting Converter
3.0″
Cin
(Bottom View)
+
CO
CF
L
RF
+
+
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
R2
-
VO
D1
Vin
-
R1
C1
+
(Top View)
Figure 24. Voltage–Inverting Converter Printed Circuit Board and Component Layout
http://onsemi.com
12
+
+
1.9 ″
MC34166
VOLTAGE-INVERTING
+
+
MC34166, MC33166
Vin
24 V
+
4
ILIMIT
+
Oscillator
1000
S
Q
R
2
PWM
UVLO
1N5822
MUR110
+
Thermal
T1
Reference
+
MUR110
VO3
1000 -12 V/100 mA
VO2
+
1000 12 V/300 mA
+
EA
6.8 k
1
1000
+
VO1
5.05 V/2.0 A
5
3
0.1
Tests
68 k
Conditions
Results
Line Regulation
5.0 V
12 V
–12 V
Vin = 15 V to 30 V, IO1 = 2.0 A, IO2 = 300 mA, IO3 = 100 mA
4.0 mV = ± 0.04%
450 mV = ±1.9%
350 mV = ±1.5%
Load Regulation
5.0 V
12 V
–12 V
Vin = 24 V, IO1 = 500 mA to 2.0 A, IO2 = 300 mA, IO3 = 100 mA
Vin = 24 V, IO1 = 2.0 A, IO2 = 100 mA to 300 mA, IO3 = 100 mA
Vin = 24 V, IO1 = 2.0 A, IO2 = 300 mA, IO3 = 30 mA to 100 mA
2.0 mV = ± 0.02%
420 mV = ±1.7%
310 mV = ±1.3%
Output Ripple
5.0 V
12 V
–12 V
Vin = 24 V, IO1 = 2.0 A, IO2 = 300 mA, IO3 = 100 mA
50 mVpp
25 mVpp
10 mVpp
Short Circuit Current
5.0 V
12 V
–12 V
Vin = 24 V, RL = 0.1 Ω
4.3 A
1.83 A
1.47 A
Vin = 24 V, IO1 = 2.0 A, IO2 = 300 mA, IO3 = 100 mA
83.3%
Efficiency
TOTAL
T1 = Primary: Coilcraft M1496-A or General Magnetics Technology GMT–0223, 42 turns of #16 AWG on Magnetics Inc. 58350-A2 core.
T1 = Secondary: VO2 – 65 turns of #26 AWG
T1 = Secondary: VO3 – 96 turns of #28 AWG
Heatsink = AAVID Engineering Inc. 5903B, or 5930B.
Multiple auxiliary outputs can easily be derived by winding secondaries on the main output inductor to form a transformer. The secondaries must
be connected so that the energy is delivered to the auxiliary outputs when the Switch Output turns off. During the OFF time, the voltage across
the primary winding is regulated by the feedback loop, yielding a constant Volts/Turn ratio. The number of turns for any given secondary voltage
can be calculated by the following equation:
# TURNS(SEC) VO(SEC) VF(SEC)
VO(PRI)VF(PRI)
#TURNS(PRI)
Note that the 12 V winding is stacked on top of the 5.0 V output. This reduces the number of secondary turns and improves lead regulation. For
best auxiliary regulation, the auxiliary outputs should be less than 33% of the total output power.
Figure 25. Triple Output Converter
http://onsemi.com
13
MC34166, MC33166
+
4
ILIMIT
Oscillator
22
0.01
1N5822
S
Q1
Q
R
L
Reference
5
Vin
-12 V
0.22
+
Z1
1
2N3906
470 k
R2
5.1 k
0.002
1000
+
+
VO
+36 V/0.25 A
R1
36 k
MTP
3055E
EA
3
MUR415
R1
D1
Thermal
+
2
UVLO
PWM
VO 5.05
R1 0.7
R2
*Gate resistor RG, zener diode D3, and diode D4 are required only when Vin is greater than 20 V.
Test
Conditions
Results
Line Regulation
Vin = –10 V to – 20 V, IO = 0.25 A
250 mV = ± 0.35%
Load Regulation
Vin = –12 V, IO = 0.025 A to 0.25 A
790 mV = ±1.19%
Output Ripple
Vin = –12 V, IO = 0.25 A
80 mVpp
Efficiency
Vin = –12 V, IO = 0.25 A
79.2%
L = Coilcraft M1496–A or ELMACO CHK1050, 42 turns of #16 AWG on Magnetics Inc.
58350–A2 core.
Heatsink = AAVID Engineering Inc. 5903B or 5930B
Figure 26. Negative Input/Positive Output Regulator
+
4
ILIMIT
Oscillator
+
Vin
18 V
1000
S
Q
R
UVLO
2
PWM
Brush
Motor
Thermal
Reference
+
EA
5
3
Test
0.1
Conditions
1N5822
+
1
5.6 k
+
1.0 k
47
56 k
Results
Low Speed Line Regulation
Vin = 12 V to 24 V
1760 RPM ±1%
High Speed Line Regulation
Vin = 12 V to 24 V
3260 RPM ± 6%
Figure 27. Variable Motor Speed Control with EMF Feedback Sensing
http://onsemi.com
14
50 k
Faster
1000
MC34166, MC33166
0.001
T1
MBR20100CT
0.001
1N5404
115 VAC
+
1000
MC34166
Step-Down
Converter
+
Output 1
0.001
RFI
Filter
+
220
MJE13005
MBR20100CT
0.047
1N4937
100k
T2
+
1000
0.01
50
0.001
MC34166
Step-Down
Converter
+
Output 2
0.001
3.3
1N4003
+
100
MBR20100CT
+
1000
0.001
T1 =
T1 =
T1 =
T1 =
T1 =
Core and Bobbin - Coilcraft PT3595
Primary - 104 turns #26 AWG
Base Drive - 3 turns #26 AWG
Secondaries - 16 turns #16 AWG
Total Gap - 0.002″
MC34166
Step-Down
Converter
+
Output 3
T2 = Core - TDK T6 x 1.5 x 3 H5C2
T2 = 14 turns center tapped #30 AWG
T2 = Heatsink = AAVID Engineering Inc.
T2 = MC34166 and MJE13005 - 5903B
T2 = MBR20100CT - 5925B
The MC34166 can be used cost effectively in off–line applications even though it is limited to a maximum input voltage of 40 V. Figure 28 shows
a simple and efficient method for converting the AC line voltage down to 24 V. This preconverter has a total power rating of 125 W with a conversion
efficiency of 90%. Transformer T1 provides output isolation from the AC line and isolation between each of the secondaries. The circuit
self–oscillates at 50 kHz and is controlled by the saturation characteristics of T2. Multiple MC34166 post regulators can be used to provide
accurate independently regulated outputs for a distributed power system.
JUNCTIONTOAIR (° C/W)
R θ JA, THERMAL RESISTANCE
80
70
3.0
Free Air
Mounted
Vertically
60
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
2.0 oz. Copper
L
Minimum
Size Pad
50
2.5
2.0
L
1.5
40
RθJA
30
3.5
PD(max) for TA = +50°C
0
5.0
10
15
20
25
30
1.0
L, LENGTH OF COPPER (mm)
Figure 29. D2PAK Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
15
PD, MAXIMUM POWER DISSIPATION (W)
Figure 28. Off–Line Preconverter
MC34166, MC33166
Table 1. Design Equations
Calculation
Step–Down
Step–Up/Down
Voltage–Inverting
ton
toff
(Notes 1, 2)
Vout VF
Vin Vsat Vout
Vout VF1 VF2
Vin VsatQ1 VsatQ2
|Vout| VF
Vin Vsat
ton
ton
toff
ton
fosc
1
toff
ton
toff
ton
fosc
1
toff
ton
toff
ton
fosc
1
toff
Duty Cycle
(Note 3)
ton fosc
ton fosc
ton fosc
IL avg
Iout
t
Iout on 1
toff
t
Iout on 1
toff
Ipk(switch)
I
IL avg L
2
I
IL avg L
2
I
IL avg L
2
L
Vin VIsatL Voutton
VsatQ2
Vin VsatQ1
ton
IL
Vin ILVsatton
Vripple(pp)
IL
1
2 (ESR)2
8foscCo
tton
1 1 2 (ESR)2
foscCo
off
tton
1 1 2 (ESR)2
foscCo
off
R
R
R
Vref 2 1
Vref 2 1
Vref 2 1
R1
R1
R1
1. Vsat – Switch Output source saturation voltage, refer to Figure 8.
2. VF – Output rectifier forward voltage drop. Typical value for 1N5822 Schottky barrier rectifier is 0.5 V.
3. Duty cycle is calculated at the minimum operating input voltage and must not exceed the guaranteed minimum DC(max) specification of 0.92.
Vout
The following converter characteristics must be chosen:
Vout – Desired output voltage.
Iout – Desired output current.
∆IL – Desired peak–to–peak inductor ripple current. For maximum output current especially when the duty cycle is greater than
0.5, it is suggested that ∆IL be chosen to be less than 10% of the average inductor current IL avg. This will help prevent
Ipk(switch) from reaching the guaranteed minimum current limit threshold of 3.3 A. If the design goal is to use a minimum
inductance value, let ∆IL = 2 (IL avg). This will proportionally reduce the converter’s output current capability.
Vripple(pp) – Desired peak–to–peak output ripple voltage. For best performance, the ripple voltage should be kept to less than 2% of Vout.
Capacitor CO should be a low equivalent series resistance (ESR) electrolytic designed for switching regulator applications.
http://onsemi.com
16
MC34166, MC33166
ORDERING INFORMATION
Device
Operating
Temperature Range
Package
MC33166D2T
D2PAK
(Surface Mount)
MC33166D2TR4
D2PAK
(Surface Mount)
MC33166T
TO–220 (Straight Lead)
TA= –40° to +85°C
MC33166TH
TO–220 (Horizontal Mount)
MC33166TV
TO–220 (Vertical Mount)
MC34166D2T
D2PAK (Surface Mount)
MC34166D2TR4
D2PAK (Surface Mount)
MC34166T
TO–220 (Straight Lead)
TA= 0° to +70°C
MC34166TH
TO–220 (Horizontal Mount)
MC34166TV
TO–220 (Vertical Mount)
http://onsemi.com
17
Shipping
50 Units/Rail
MC34166, MC33166
PACKAGE DIMENSIONS
TO–220
TH SUFFIX
CASE 314A–03
ISSUE E
–T–
B
–P–
Q
C
E
OPTIONAL
CHAMFER
A
U
F
L
K
G
5X
J
S
D
5X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 0.043 (1.092) MAXIMUM.
SEATING
PLANE
0.014 (0.356)
M
T P
M
DIM
A
B
C
D
E
F
G
J
K
L
Q
S
U
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.570
0.585
0.067 BSC
0.015
0.025
0.730
0.745
0.320
0.365
0.140
0.153
0.210
0.260
0.468
0.505
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
4.318
4.572
0.635
0.965
1.219
1.397
14.478 14.859
1.702 BSC
0.381
0.635
18.542 18.923
8.128
9.271
3.556
3.886
5.334
6.604
11.888 12.827
TO–220
TV SUFFIX
CASE 314B–05
ISSUE J
Q
OPTIONAL
CHAMFER
E
A
U
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 0.043 (1.092) MAXIMUM.
C
B
–P–
S
L
W
V
F
5X
G
5X
0.24 (0.610)
M
J
T
H
D
0.10 (0.254)
M
T P
N
M
–T–
http://onsemi.com
18
SEATING
PLANE
DIM
A
B
C
D
E
F
G
H
J
K
L
N
Q
S
U
V
W
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.850
0.935
0.067 BSC
0.166 BSC
0.015
0.025
0.900
1.100
0.320
0.365
0.320 BSC
0.140
0.153
--0.620
0.468
0.505
--0.735
0.090
0.110
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
4.318
4.572
0.635
0.965
1.219
1.397
21.590 23.749
1.702 BSC
4.216 BSC
0.381
0.635
22.860 27.940
8.128
9.271
8.128 BSC
3.556
3.886
--- 15.748
11.888 12.827
--- 18.669
2.286
2.794
MC34166, MC33166
PACKAGE DIMENSIONS
TO–220
T SUFFIX
CASE 314D–04
ISSUE E
–T–
–Q–
SEATING
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
C
B
E
A
U
L
K
J
H
G
D
DIM
A
B
C
D
E
G
H
J
K
L
Q
U
1234 5
5 PL
0.356 (0.014)
T Q
M
M
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.067 BSC
0.087
0.112
0.015
0.025
0.990
1.045
0.320
0.365
0.140
0.153
0.105
0.117
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
4.318
4.572
0.635
0.965
1.219
1.397
1.702 BSC
2.210
2.845
0.381
0.635
25.146 26.543
8.128
9.271
3.556
3.886
2.667
2.972
D2PAK
D2T SUFFIX
CASE 936A–02
ISSUE B
–T–
OPTIONAL
CHAMFER
A
TERMINAL 6
E
U
S
K
B
V
H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
A AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 6.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAXIMUM.
1 2 3 4 5
M
D
0.010 (0.254)
M
T
L
P
N
G
R
C
http://onsemi.com
19
DIM
A
B
C
D
E
G
H
K
L
M
N
P
R
S
U
V
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.067 BSC
0.539
0.579
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.702 BSC
13.691 14.707
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 REF
2.946 REF
5.080 MIN
6.350 MIN
MC34166, MC33166
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
20
MC34166/D