CYPRESS CY7C1441AV33

CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
36-Mbit (1 M × 36/2 M × 18/512 K × 72)
Flow-Through SRAM
36-Mbit (1 M × 36/2 M × 18/512 K × 72) Flow-Through SRAM
Features
Functional Description
■
Supports 133-MHz bus operations
■
1 M × 36/2 M × 18/512 K × 72 common IO
■
3.3 V core power supply
■
2.5 V or 3.3 V IO power supply
■
Fast clock-to-output times
❐ 6.5 ns (133-MHz version)
■
Provide high-performance 2-1-1-1 access rate
■
User-selectable burst counter supporting Intel Pentium
interleaved or linear burst sequences
■
Separate processor and controller address strobes
■
Synchronous self-timed write
■
Asynchronous output enable
■
CY7C1441AV33,
CY7C1443AV33
available
in
JEDEC-standard Pb-free 100-pin TQFP package, Pb-free and
non Pb-free 165-ball FBGA package. CY7C1447AV33
available in Pb-free and non Pb-free 209-ball FBGA package
■
IEEE 1149.1 JTAG-Compatible Boundary Scan
■
“ZZ” Sleep Mode option
The CY7C1441AV33/CY7C1443AV33/CY7C1447AV33[1] are
3.3 V, 1 M × 36/2 M × 18/512 K × 72 Synchronous Flow-through
SRAMs, respectively designed to interface with high-speed
microprocessors with minimum glue logic. Maximum access
delay from clock rise is 6.5 ns (133-MHz version). A 2-bit on-chip
counter captures the first address in a burst and increments the
address automatically for the rest of the burst access. All
synchronous inputs are gated by registers controlled by a
positive-edge-triggered Clock Input (CLK). The synchronous
inputs include all addresses, all data inputs, address-pipelining
Chip Enable (CE1), depth-expansion Chip Enables (CE2 and
CE3), Burst Control inputs (ADSC, ADSP, and ADV), Write
Enables (BWx, and BWE), and Global Write (GW).
Asynchronous inputs include the Output Enable (OE) and the ZZ
pin.
The CY7C1441AV33/CY7C1443AV33/CY7C1447AV33 allows
either interleaved or linear burst sequences, selected by the
MODE input pin. A HIGH selects an interleaved burst sequence,
while a LOW selects a linear burst sequence. Burst accesses
can be initiated with the Processor Address Strobe (ADSP) or the
cache Controller Address Strobe (ADSC) inputs. Address
advancement is controlled by the Address Advancement (ADV)
input.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or Address
Strobe Controller (ADSC) are active. Subsequent burst
addresses can be internally generated as controlled by the
Advance pin (ADV).
The
CY7C1441AV33/CY7C1443AV33/CY7C1447AV33
operates from a +3.3 V core power supply while all outputs may
operate with either a +2.5 or +3.3 V supply. All inputs and outputs
are JEDEC-standard JESD8-5-compatible.
Selection Guide
133 MHz
100 MHz
Unit
Maximum Access Time
Description
6.5
8.5
ns
Maximum Operating Current
310
290
mA
Maximum CMOS Standby Current
120
120
mA
Note
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document Number: 38-05357 Rev. *I
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 23, 2011
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Logic Block Diagram – CY7C1441AV33 (1 M × 36)
ADDRESS
REGISTER
A 0, A1, A
A [1:0]
MODE
BURST Q1
COUNTER
AND LOGIC
Q0
CLR
ADV
CLK
ADSC
ADSP
DQ D , DQP D
DQ D , DQP D
BW D
BYTE
BYTE
WRITE REGISTER
WRITE REGISTER
DQ C, DQP C
DQ C, DQP C
BW C
BYTE
BYTE
WRITE REGISTER
WRITE REGISTER
DQ B , DQP B
BW B
DQ B , DQP B
BYTE
BYTE
WRITE REGISTER
MEMORY
ARRAY
SENSE
AMPS
OUTPUT
BUFFERS
DQ s
DQP A
DQP B
DQP C
DQP D
WRITE REGISTER
DQ A , DQP A
BW A
BWE
DQ A , DQPA
BYTE
BYTE
WRITE REGISTER
WRITE REGISTER
INPUT
REGISTERS
GW
ENABLE
REGISTER
CE1
CE2
CE3
OE
ZZ
SLEEP
CONTROL
Logic Block Diagram – CY7C1443AV33 (2 M × 18)
A0,A1,A
ADDRESS
REGISTER
A[1:0]
MODE
BURST Q1
COUNTER AND
LOGIC
CLR
Q0
ADV
CLK
ADSC
ADSP
BW B
BW A
DQ B ,DQP B
WRITE REGISTER
DQ A ,DQP A
WRITE REGISTER
DQ B ,DQP B
WRITE DRIVER
MEMORY
ARRAY
SENSE
AMPS
OUTPUT
BUFFERS
DQs
DQP A
DQP B
DQ A ,DQP A
WRITE DRIVER
BWE
GW
CE 1
CE 2
CE 3
ENABLE
REGISTER
INPUT
REGISTERS
OE
ZZ
SLEEP
CONTROL
Document Number: 38-05357 Rev. *I
Page 2 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Logic Block Diagram – CY7C1447AV33 (512 K × 72)
ADDRESS
REGISTER
A0, A1,A
A[1:0]
MODE
BURST Q1
COUNTER
AND LOGIC
CLR
Q0
ADV
CLK
ADSC
ADSP
BW H
DQ H , DQPH
WRITE REGISTER
DQ H , DQPH
WRITE DRIVER
BW G
DQ F, DQPF
WRITE REGISTER
DQ G , DQPG
WRITE DRIVER
BW F
DQ F, DQPF
WRITE REGISTER
DQ F, DQPF
WRITE DRIVER
BW E
DQ E , DQPE
WRITE REGISTER
DQ
E , DQP
“a” E
BYTE
WRITE DRIVER
BW D
DQ D , DQPD
WRITE REGISTER
DQ D , DQPD
WRITE DRIVER
BW C
DQ C, DQPC
WRITE REGISTER
DQ C, DQPC
WRITE DRIVER
MEMORY
ARRAY
SENSE
AMPS
BW B
BW A
BWE
DQ B , DQPB
WRITE REGISTER
DQ A , DQPA
WRITE REGISTER
GW
CE1
CE2
CE3
OE
ZZ
ENABLE
REGISTER
OUTPUT
BUFFERS
DQs
DQP A
DQP B
DQP C
DQP D
DQP E
DQP F
DQP G
DQP H
DQ B , DQPB
WRITE DRIVER
DQ A , DQPA
WRITE DRIVER
INPUT
REGISTERS
SLEEP
CONTROL
Document Number: 38-05357 Rev. *I
Page 3 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Contents
Pin Configurations ........................................................... 5
Pin Definitions .................................................................. 8
Functional Overview ...................................................... 10
Single Read Accesses .............................................. 10
Single Write Accesses Initiated by ADSP ................. 10
Single Write Accesses Initiated by ADSC ................. 10
Burst Sequences ....................................................... 10
Sleep Mode ............................................................... 10
Interleaved Burst Address Table
(MODE = Floating or VDD) ............................................. 10
Linear Burst Address Table (MODE = GND) ................ 10
ZZ Mode Electrical Characteristics ............................... 11
Truth Table ...................................................................... 11
Partial Truth Table for Read/Write ................................ 12
Truth Table for Read/Write ............................................ 12
Truth Table for Read/Write ............................................ 12
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 13
Disabling the JTAG Feature ...................................... 13
TAP Controller State Diagram ....................................... 13
Test Access Port (TAP) ............................................. 13
TAP Controller Block Diagram ...................................... 13
PERFORMING A TAP RESET .................................. 13
TAP REGISTERS ...................................................... 13
TAP Instruction Set ................................................... 14
TAP Timing ...................................................................... 15
TAP AC Switching Characteristics ............................... 16
3.3 V TAP AC Test Conditions ....................................... 17
3.3 V TAP AC Output Load Equivalent ......................... 17
Document Number: 38-05357 Rev. *I
2.5 V TAP AC Test Conditions ....................................... 17
2.5V TAP AC Output Load Equivalent .......................... 17
TAP DC Electrical Characteristics and
Operating Conditions ..................................................... 17
Identification Register Definitions ................................ 18
Scan Register Sizes ....................................................... 18
Identification Codes ....................................................... 18
165-ball FBGA Boundary Scan Order ........................... 19
Maximum Ratings ........................................................... 20
Operating Range ............................................................. 20
Electrical Characteristics ............................................... 20
DC Electrical Characteristics ..................................... 20
Capacitance .................................................................... 21
Parameter ........................................................................ 21
Thermal Resistance ........................................................ 21
Switching Characteristics .............................................. 22
Timing Diagrams ............................................................ 23
Ordering Information ...................................................... 27
Ordering Code Definitions ......................................... 27
Package Diagrams .......................................................... 28
Acronyms ........................................................................ 31
Document Conventions ................................................. 31
Units of Measure ....................................................... 31
Document History Page ................................................. 32
Sales, Solutions, and Legal Information ...................... 34
Worldwide Sales and Design Support ....................... 34
Products .................................................................... 34
PSoC Solutions ......................................................... 34
Page 4 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Pin Configurations
NC
NC
NC
CY7C1443AV33
(2 M × 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Document Number: 38-05357 Rev. *I
A
NC
NC
VDDQ
VSSQ
NC
DQPA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
NC
NC
VSSQ
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VDDQ
VSSQ
NC
NC
DQB
DQB
VSSQ
VDDQ
DQB
DQB
NC
VDD
NC
VSS
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQPB
NC
VSSQ
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
NC/72M
A
VSS
VDD
DQPB
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
DQPA
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
CY7C1441AV33
(1 M × 36)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
NC/72M
A
VSS
VDD
A
A
A
A
A
A
A
A
A
DQPC
DQC
DQC
VDDQ
VSSQ
DQC
DQC
DQC
DQC
VSSQ
VDDQ
DQC
DQC
NC
VDD
NC
VSS
DQD
DQD
VDDQ
VSSQ
DQD
DQD
DQD
DQD
VSSQ
VDDQ
DQD
DQD
DQPD
A
A
CE1
CE2
NC
NC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE1
CE2
BWD
BWC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
Figure 1. 100-pin TQFP Pinout
Page 5 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Pin Configurations (continued)
165-ball FBGA (15 × 17 × 1.4 mm) Pinout
CY7C1441AV33 (1 M × 36)
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/288M
1
A
CE1
BWC
BWB
CE3
BWE
ADSC
ADV
A
NC
NC/144M
A
CE2
BWD
BWA
CLK
GW
OE
ADSP
A
NC/576M
DQPC
DQC
NC
DQC
VDDQ
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
NC/1G
DQB
DQPB
DQB
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
DQC
NC
DQD
DQC
VDDQ
VDDQ
NC
VDDQ
VDD
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
DQB
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
DQC
NC
DQD
DQB
NC
DQA
DQB
DQB
ZZ
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQPD
DQD
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
A
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
DQA
DQPA
NC
NC/72M
A
A
TDI
A1
TDO
A
A
A
A
R
MODE
A
A
A
TMS
A0
TCK
A
A
A
A
CY7C1443AV33 (2 M × 18)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/288M
A
CE1
BWB
NC
CE3
BWE
ADSC
ADV
A
A
NC/144M
A
CE2
NC
BWA
CLK
GW
OE
ADSP
A
NC
NC
NC
DQB
VDDQ
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
NC/1G
NC
NC
DQB
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
NC
NC
NC
DQB
DQB
VDD
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
DQB
NC
NC
VDDQ
VDDQ
NC
VDDQ
NC
NC
DQA
DQA
DQA
ZZ
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
R
NC/576M
DQPA
DQA
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
DQPB
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
A
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
NC
NC
NC
NC/72M
A
A
TDI
A1
TDO
A
A
A
A
MODE
A
A
A
TMS
A0
TCK
A
A
A
A
Document Number: 38-05357 Rev. *I
Page 6 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Pin Configurations (continued)
209-ball FBGA (14 × 22 × 1.76 mm) Pinout
CY7C1447AV33 (512 K × 72)
1
2
3
4
5
6
7
8
9
10
11
A
DQG
DQG
A
CE2
ADSP
ADSC
ADV
CE3
A
DQB
DQB
B
DQG
DQG
BWSC
BWSG
NC288M
A
BWSB
BWSF
DQB
DQB
C
DQG
DQG
BWSH
BWSD NC/144M CE1
NC/576M
BWSE
BWSA
DQB
DQB
D
DQG
DQG
VSS
NC
NC/1G
OE
NC
VSS
DQB
DQB
E
DQPG
DQPC
VDDQ
VDDQ
VDD
VDD
VDD
VDDQ
VDDQ
DQPF
DQPB
F
DQC
DQC
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQF
DQF
G
DQC
DQC
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQF
DQF
H
DQC
DQC
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQF
DQF
J
DQC
DQC
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQF
DQF
K
NC
NC
CLK
NC
VSS
VSS
VSS
NC
NC
NC
NC
L
DQH
DQH
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQA
DQA
M
DQH
DQH
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQA
DQA
N
DQH
DQH
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQA
DQA
P
DQH
DQH
VSS
VSS
VSS
ZZ
VSS
VSS
VSS
DQA
DQA
R
DQPD
DQPH
VDDQ
VDDQ
VDD
VDD
VDD
VDDQ
VDDQ
T
DQD
DQD
VSS
NC
NC
MODE
NC
NC
VSS
DQE
DQE
U
DQD
DQD
V
DQD
DQD
W
DQD
DQD
Document Number: 38-05357 Rev. *I
BW
GW
DQPA
DQPE
A
A
A
A
A
A
DQE
DQE
A
A
A
A1
A
A
A
DQE
DQE
TMS
TDI
A
A0
A
TCK
DQE
DQE
NC/72M
TDO
Page 7 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Pin Definitions
Name
IO
Description
A0, A1, A
InputSynchronous
Address Inputs Used to Select One of the Address Locations. Sampled at the rising edge
of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A[1:0]
feed the 2-bit counter.
BWA, BWB,
BWC, BWD,
BWE, BWF,
BWG, BWH
InputSynchronous
Byte Write Select Inputs, Active LOW. Qualified with BWE to conduct byte writes to the SRAM.
Sampled on the rising edge of CLK.
GW
InputSynchronous
Global Write Enable Input, Active LOW. When asserted LOW on the rising edge of CLK, a
global write is conducted (ALL bytes are written, regardless of the values on BWX and BWE).
CLK
InputClock
Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the
burst counter when ADV is asserted LOW, during a burst operation.
CE1
InputSynchronous
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE1 is sampled only
when a new external address is loaded.
CE2
InputSynchronous
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE3 to select/deselect the device. CE2 is sampled only when a new external
address is loaded.
CE3
InputSynchronous
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE1 and CE2 to select/deselect the device. CE3 is assumed active throughout this document for
BGA. CE3 is sampled only when a new external address is loaded.
OE
InputAsynchronous
Output Enable, Asynchronous Input, Active LOW. Controls the direction of the IO pins. When
LOW, the IO pins behave as outputs. When deasserted HIGH, IO pins are tri-stated, and act as
input data pins. OE is masked during the first clock of a read cycle when emerging from a
deselected state.
ADV
InputSynchronous
Advance Input Signal, Sampled on the Rising Edge of CLK. When asserted, it automatically
increments the address in a burst cycle.
ADSP
InputSynchronous
Address Strobe from Processor, Sampled on the Rising Edge of CLK, Active LOW. When
asserted LOW, addresses presented to the device are captured in the address registers. A[1:0]
are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is
recognized. ASDP is ignored when CE1 is deasserted HIGH
ADSC
InputSynchronous
Address Strobe from Controller, Sampled on the Rising Edge of CLK, Active LOW. When
asserted LOW, addresses presented to the device are captured in the address registers. A[1:0]
are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is
recognized.
BWE
InputSynchronous
Byte Write Enable Input, Active LOW. Sampled on the rising edge of CLK. This signal must
be asserted LOW to conduct a byte write.
ZZ
InputAsynchronous
ZZ “sleep” Input, Active HIGH. When asserted HIGH places the device in a non-time-critical
“sleep” condition with data integrity preserved. For normal operation, this pin must be LOW or
left floating. ZZ pin has an internal pull down.
DQs
IOSynchronous
Bidirectional Data IO lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by the addresses presented during the previous clock rise of the read cycle. The
direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs.
When HIGH, DQs and DQPX are placed in a tri-state condition.The outputs are automatically
tri-stated during the data portion of a write sequence, during the first clock when emerging from
a deselected state, and when the device is deselected, regardless of the state of OE.
DQPX
IOSynchronous
Bidirectional Data Parity IO Lines. Functionally, these signals are identical to DQs. During write
sequences, DQPx is controlled by BW[A:H] correspondingly.
MODE
Input-Static
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left
floating selects interleaved burst sequence. This is a strap pin and should remain static during
device operation. Mode Pin has an internal pull up.
Document Number: 38-05357 Rev. *I
Page 8 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Pin Definitions (continued)
Name
VDD
VDDQ
VSS
VSSQ
IO
Power Supply
Description
Power Supply Inputs to the Core of the Device.
IO Power Supply Power Supply for the IO Circuitry.
Ground
IO Ground
Ground for the Core of the Device.
Ground for the IO Circuitry.
TDO
JTAG serial output Serial Data-Out to the JTAG Circuit. Delivers data on the negative edge of TCK. If the JTAG
Synchronous
feature is not being utilized, this pin should be left unconnected. This pin is not available on TQFP
packages.
TDI
JTAG serial input Serial Data-In to the JTAG Circuit. Sampled on the rising edge of TCK. If the JTAG feature is
Synchronous
not being utilized, this pin can be left floating or connected to VDD through a pull up resistor. This
pin is not available on TQFP packages.
TMS
JTAG serial input Serial Data-In to the JTAG Circuit. Sampled on the rising edge of TCK. If the JTAG feature is
Synchronous
not being utilized, this pin can be disconnected or connected to VDD. This pin is not available on
TQFP packages.
TCK
JTAG-Clock
Clock Input to the JTAG Circuitry. If the JTAG feature is not being utilized, this pin must be
connected to VSS. This pin is not available on TQFP packages.
NC
-
No Connects. Not internally connected to the die. 72M, 144M and 288M are address expansion
pins are not internally connected to the die.
NC/72M,
NC/144M,
NC/288M,
NC/576M,
NC/1G
-
No Connects. Not internally connected to the die. NC/72M, NC/144M, NC/288M, NC/576M and
NC/1G are address expansion pins are not internally connected to the die.
Document Number: 38-05357 Rev. *I
Page 9 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Functional Overview
HIGH, and (4) the write input signals (GW, BWE, and BWX)
indicate a write access. ADSC is ignored if ADSP is active LOW.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. Maximum access delay from the
clock rise (t CDV) is 6.5 ns (133-MHz device).
The addresses presented are loaded into the address register
and the burst counter/control logic and delivered to the memory
core. The information presented to DQS is written into the
specified address location. Byte writes are allowed. All IOs are
tri-stated when a write is detected, even a byte write. Since this
is a common IO device, the asynchronous OE input signal must
be deasserted and the IOs must be tri-stated prior to the presentation of data to DQs. As a safety precaution, the data lines are
tri-stated once a write cycle is detected, regardless of the state
of OE.
The
CY7C1441AV33/CY7C1443AV33/CY7C1447AV33
supports secondary cache in systems utilizing either a linear or
interleaved burst sequence. The interleaved burst order
supports Pentium and i486™ processors. The linear burst
sequence is suited for processors that utilize a linear burst
sequence. The burst order is user-selectable, and is determined
by sampling the MODE input. Accesses can be initiated with
either the Processor Address Strobe (ADSP) or the Controller
Address Strobe (ADSC). Address advancement through the
burst sequence is controlled by the ADV input. A two-bit on-chip
wraparound burst counter captures the first address in a burst
sequence and automatically increments the address for the rest
of the burst access.
Byte write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BWx) inputs. A Global Write
Enable (GW) overrides all byte write inputs and writes data to all
four bytes. All writes are simplified with on-chip synchronous
self-timed write circuitry.
Three synchronous Chip Selects (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE1 is
HIGH.
Single Read Accesses
A single read access is initiated when the following conditions
are satisfied at clock rise: (1) CE1, CE2, and CE3 are all asserted
active, and (2) ADSP or ADSC is asserted LOW (if the access is
initiated by ADSC, the write inputs must be deasserted during
this first cycle). The address presented to the address inputs is
latched into the address register and the burst counter/control
logic and presented to the memory core. If the OE input is
asserted LOW, the requested data is available at the data
outputs a maximum to tCDV after clock rise. ADSP is ignored if
CE1 is HIGH.
Burst Sequences
The
CY7C1441AV33/CY7C1443AV33/CY7C1447AV33
provides an on-chip two-bit wraparound burst counter inside the
SRAM. The burst counter is fed by A[1:0], and can follow either a
linear or interleaved burst order. The burst order is determined
by the state of the MODE input. A LOW on MODE selects a linear
burst sequence. A HIGH on MODE selects an interleaved burst
order. Leaving MODE unconnected causes the device to default
to a interleaved burst sequence.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected prior to entering the “sleep” mode. CE1, CE2,
CE3, ADSP, and ADSC must remain inactive for the duration of
tZZREC after the ZZ input returns LOW.
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
Single Write Accesses Initiated by ADSP
00
01
10
11
This access is initiated when the following conditions are
satisfied at clock rise: (1) CE1, CE2, CE3 are all asserted active,
and (2) ADSP is asserted LOW. The addresses presented are
loaded into the address register and the burst inputs (GW, BWE,
and BWX)are ignored during this first clock cycle. If the write
inputs are asserted active (see Write Cycle Descriptions table for
appropriate states that indicate a write) on the next clock rise, the
appropriate data is latched and written into the device. Byte
writes are allowed. All IOs are tri-stated during a byte write.Since
this is a common IO device, the asynchronous OE input signal
must be deasserted and the IOs must be tri-stated prior to the
presentation of data to DQs. As a safety precaution, the data
lines are tri-stated once a write cycle is detected, regardless of
the state of OE.
01
00
11
10
10
11
00
01
11
10
01
00
Single Write Accesses Initiated by ADSC
This write access is initiated when the following conditions are
satisfied at clock rise: (1) CE1, CE2, and CE3 are all asserted
active, (2) ADSC is asserted LOW, (3) ADSP is deasserted
Document Number: 38-05357 Rev. *I
Linear Burst Address Table (MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Page 10 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
ZZ Mode Electrical Characteristics
Parameter
IDDZZ
tZZS
tZZREC
tZZI
tRZZI
Description
Test Conditions
ZZ > VDD– 0.2 V
ZZ > VDD – 0.2 V
ZZ < 0.2 V
This parameter is sampled
This parameter is sampled
Sleep mode standby current
Device operation to ZZ
ZZ recovery time
ZZ active to sleep current
ZZ Inactive to exit sleep current
Min
Max
Unit
–
–
100
2tCYC
–
2tCYC
–
mA
ns
ns
ns
ns
2tCYC
–
0
Truth Table
tThe truth table for CY7C1441AV33/CY7C1443AV33/CY7C1447AV33 follows.[2, 3, 4, 5, 6]
Cycle Description
Address
Used
Deselected Cycle, Power down
None
H
Deselected Cycle, Power down
None
L
L
Deselected Cycle, Power down
None
L
X
Deselected Cycle, Power down
None
L
L
Deselected Cycle, Power down
None
X
Sleep Mode, Power down
CE1 CE2 CE3
ZZ
ADSP
ADSC
ADV
WRITE
OE
CLK
DQ
L
X
L
X
X
X
L–H
Tri-State
X
L
L
X
X
X
X
L–H
Tri-State
H
L
L
X
X
X
X
L–H
Tri-State
X
L
H
L
X
X
X
L–H
Tri-State
X
X
L
H
L
X
X
X
L–H
Tri-State
X
X
None
X
X
X
H
X
X
X
X
X
X
Tri-State
Read Cycle, Begin Burst
Read Cycle, Begin Burst
Write Cycle, Begin Burst
Read Cycle, Begin Burst
Read Cycle, Begin Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
External
External
External
External
External
Next
Next
Next
L
L
L
L
L
X
X
H
H
H
H
H
H
X
X
X
L
L
L
L
L
X
X
X
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
X
X
X
L
L
L
H
H
H
X
X
X
X
X
L
L
L
X
X
L
H
H
H
H
H
L
H
X
L
H
L
H
L
L–H
L–H
L–H
L–H
L–H
L–H
L–H
L–H
Q
Tri-State
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
H
L–H
Tri-State
Write Cycle, Continue Burst
Next
X
X
X
L
H
H
L
L
X
L–H
D
Write Cycle, Continue Burst
Next
H
X
X
L
X
H
L
L
X
L–H
D
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
L
L–H
Q
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
H
L–H
Tri-State
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
L
L–H
Q
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
H
L–H
Tri-State
Write Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
L
X
L–H
D
Write Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
L
X
L–H
D
D
Q
Tri-State
Q
Tri-State
Q
Notes
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write enable signals and BWE = L or GW = L. WRITE = H when all Byte write enable signals, BWE, GW = H.
4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after
the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't care
for the remainder of the write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is
inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document Number: 38-05357 Rev. *I
Page 11 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Partial Truth Table for Read/Write
Function (CY7C1441AV33)[7, 8]
GW
BWE
BWD
BWC
BWB
BWA
Read
H
H
X
X
X
X
Read
H
L
H
H
H
H
Write Byte A (DQA, DQPA)
H
L
H
H
H
L
Write Byte B(DQB, DQPB)
H
L
H
H
L
H
Write Bytes A, B (DQA, DQB, DQPA, DQPB)
H
L
H
H
L
L
Write Byte C (DQC, DQPC)
H
L
H
L
H
H
Write Bytes C, A (DQC, DQA, DQPC, DQPA)
H
L
H
L
H
L
Write Bytes C, B (DQC, DQB, DQPC, DQPB)
H
L
H
L
L
H
Write Bytes C, B, A (DQC, DQB, DQA, DQPC, DQPB, DQPA)
H
L
H
L
L
L
Write Byte D (DQD, DQPD)
H
L
L
H
H
H
Write Bytes D, A (DQD, DQA, DQPD, DQPA)
H
L
L
H
H
L
Write Bytes D, B (DQD, DQA, DQPD, DQPA)
H
L
L
H
L
H
Write Bytes D, B, A (DQD, DQB, DQA, DQPD, DQPB, DQPA)
H
L
L
H
L
L
Write Bytes D, B (DQD, DQB, DQPD, DQPB)
H
L
L
L
H
H
Write Bytes D, B, A (DQD, DQC, DQA, DQPD, DQPC, DQPA)
H
L
L
L
H
L
Write Bytes D, C, A (DQD, DQB, DQA, DQPD, DQPB, DQPA)
H
L
L
L
L
H
Write All Bytes
H
L
L
L
L
L
Write All Bytes
L
X
X
X
X
X
GW
BWE
BWB
BWA
Read
H
H
X
X
Read
H
L
H
H
Write Byte A - (DQA and DQPA)
H
L
H
L
Truth Table for Read/Write
Function (CY7C1443AV33)[7]
Write Byte B - (DQB and DQPB)
H
L
L
H
Write All Bytes
H
L
L
L
Write All Bytes
L
X
X
X
Read
GW
H
BWE
H
BWX
X
Read
H
L
All BW = H
Truth Table for Read/Write
Function (CY7C1447AV33)[7, 9]
Write Byte x – (DQx and DQPx)
H
L
L
Write All Bytes
H
L
All BW = L
Write All Bytes
L
X
X
Notes
7. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
8. Table only lists a partial listing of the byte write combinations. Any Combination of BWX is valid Appropriate write is done based on which byte write is active.
9. BWx represents any byte write signal BW[A..H].To enable any byte write BWx, a Logic LOW signal should be applied at clock rise.Any number of bye writes can be
enabled at the same time for any given write.
Document Number: 38-05357 Rev. *I
Page 12 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
IEEE 1149.1 Serial Boundary Scan (JTAG)
The
CY7C1441AV33/CY7C1443AV33/CY7C1447AV33
incorporates a serial boundary scan test access port (TAP). This
part is fully compliant with 1149.1. The TAP operates using
JEDEC-standard 3.3 V or 2.5 V IO logic levels.
The
CY7C1441AV33/CY7C1443AV33/CY7C1447AV33
contains a TAP controller, instruction register, boundary scan
register, bypass register, and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull up resistor. TDO
should be left unconnected. Upon power up, the device comes
up in a reset state which does not interfere with the operation of
the device.
TAP Controller State Diagram
Test MODE SELECT (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. TDI is internally pulled
up and can be unconnected if the TAP is unused in an
application. TDI is connected to the most significant bit (MSB) of
any register. (See TAP Controller Block Diagram.)
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of any
register. (See TAP Controller State Diagram.)
TAP Controller Block Diagram
1
TEST-LOGIC
RESET
0
RUN-TEST/
IDLE
0
1
SELECT
DR-SCAN
1
SELECT
IR-SCAN
0
1
CAPTURE-DR
2 1 0
CAPTURE-IR
TDI
0
SHIFT-DR
0
SHIFT-IR
1
Selection
Circuitry
1
1
PAUSE-IR
1
TDO
x . . . . . 2 1 0
Boundary Scan Register
0
0
Selection
Circuitry
Identification Register
EXIT1-IR
0
PAUSE-DR
Instruction Register
31 30 29 . . . 2 1 0
0
1
EXIT1-DR
0
1
EXIT2-DR
0
EXIT2-IR
TCK
1
TM S
1
UPDATE-DR
1
Bypass Register
0
1
0
0
0
1
0
TAP CONTROLLER
UPDATE-IR
1
0
Performing a TAP Reset
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
Test Access Port (TAP)
At power up, the TAP is reset internally to ensure that TDO
comes up in a High Z state.
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Document Number: 38-05357 Rev. *I
TAP Registers
Registers are connected between the TDI and TDO balls and
scan data into and out of the SRAM test circuitry. Only one
register can be selected at a time through the instruction register.
Data is serially loaded into the TDI ball on the rising edge of TCK.
Data is output on the TDO ball on the falling edge of TCK.
Page 13 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Instruction Register
IDCODE
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram on
page 13. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO balls and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to allow for
fault isolation of the board-level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This shifts data through the SRAM with
minimal delay. The bypass register is set LOW (VSS) when the
BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM IO ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the IO ring.
The Boundary Scan Order tables show the order in which the bits
are connected. Each bit corresponds to one of the bumps on the
SRAM package. The MSB of the register is connected to TDI,
and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in the Identification Register Definitions
table.
TAP Instruction Set
Overview
The IDCODE instruction is loaded into the instruction register
upon power up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High Z state until the next command is given during the
“Update IR” state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output undergoes a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK captured in the boundary scan register.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells prior to the selection
of another boundary scan test operation.
Eight different instructions are possible with the three bit
instruction register. All combinations are listed in the Instruction
Codes table. Three of these instructions are listed as
RESERVED and should not be used. The other five instructions
are described in this section in detail.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required—that is, while data captured
is shifted out, the preloaded data can be shifted in.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction once it is shifted in, the TAP controller must be
moved into the Update-IR state.
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
Document Number: 38-05357 Rev. *I
BYPASS
Page 14 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
the current instruction. When HIGH, it enables the output buffers
to drive the output bus. When LOW, this bit places the output bus
into a High Z condition.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the shift-DR controller state.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the “Shift-DR” state. During “Update-DR”, the value
loaded into that shift-register cell latches into the preload
register. When the EXTEST instruction is entered, this bit directly
controls the output Q-bus pins. Note that this bit is pre-set HIGH
to enable the output when the device is powered-up, and also
when the TAP controller is in the “Test-Logic-Reset” state.
EXTEST OUTPUT BUS TRI-STATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tri-state mode.
The boundary scan register has a special bit located at bit #89
(for 165-ball FBGA package) or bit #138 (for 209-ball FBGA
package). When this scan cell, called the “extest output bus
tri-state”, is latched into the preload register during the
“Update-DR” state in the TAP controller, it directly controls the
state of the output (Q-bus) pins, when the EXTEST is entered as
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
Test Clock
(TCK)
3
t
t TH
t TMSS
t TMSH
t TDIS
t TDIH
TL
4
5
6
t CYC
Test Mode Select
(TMS)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CARE
Document Number: 38-05357 Rev. *I
UNDEFINED
Page 15 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
TAP AC Switching Characteristics
Over the Operating Range[9, 10]
Parameter
Description
Min
Max
Unit
Clock
tTCYC
TCK Clock Cycle Time
50
–
ns
tTF
TCK Clock Frequency
–
20
MHz
tTH
TCK Clock HIGH time
20
–
ns
tTL
TCK Clock LOW time
20
–
ns
tTDOV
TCK Clock LOW to TDO Valid
–
10
ns
tTDOX
TCK Clock LOW to TDO Invalid
0
–
ns
tTMSS
TMS Setup to TCK Clock Rise
5
–
ns
tTDIS
TDI Setup to TCK Clock Rise
5
–
ns
tCS
Capture Setup to TCK Rise
5
–
ns
tTMSH
TMS Hold after TCK Clock Rise
5
–
ns
tTDIH
TDI Hold after Clock Rise
5
–
ns
tCH
Capture Hold after Clock Rise
5
–
ns
Output Times
Setup Times
Hold Times
Notes
9. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
10. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1 ns.
Document Number: 38-05357 Rev. *I
Page 16 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
3.3 V TAP AC Test Conditions
2.5 V TAP AC Test Conditions
Input pulse levels ...............................................VSS to 3.3 V
Input pulse levels ............................................... VSS to 2.5 V
Input rise and fall times ...................................................1 ns
Input rise and fall time ....................................................1 ns
Input timing reference levels ......................................... 1.5 V
Input timing reference levels ....................................... 1.25 V
Output reference levels ................................................ 1.5 V
Output reference levels .............................................. 1.25 V
Test load termination supply voltage ............................. 1.5 V
Test load termination supply voltage .......................... 1.25 V
3.3 V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
Z O = 50 Ω
Z O = 50 Ω
20p F
20p F
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 3.135 V to 3.6 V unless otherwise noted)[11]
Parameter
VOH1
VOH2
VOL1
VOL2
VIH
VIL
IX
Description
Output HIGH Voltage
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Min
Max
Unit
IOH = –4.0 mA
VDDQ = 3.3 V
2.4
–
V
IOH = –1.0 mA
VDDQ = 2.5 V
2.0
–
V
IOH = –100 µA
VDDQ = 3.3 V
2.9
–
V
VDDQ = 2.5 V
2.1
–
V
IOL = 8.0 mA
VDDQ = 3.3 V
–
0.4
V
IOL = 1.0 mA
VDDQ = 2.5 V
–
0.4
V
IOL = 100 µA
VDDQ = 3.3 V
–
0.2
V
VDDQ = 2.5 V
–
0.2
V
VDDQ = 3.3 V
2.0
VDD + 0.3
V
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VDDQ = 3.3 V
–0.3
0.8
V
VDDQ = 2.5 V
–0.3
0.7
V
–5
5
µA
Input HIGH Voltage
Input LOW Voltage
Input Load Current
Conditions
GND < VIN < VDDQ
Note
11. All voltages referenced to VSS (GND).
Document Number: 38-05357 Rev. *I
Page 17 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Identification Register Definitions
CY7C1441AV33 CY7C1443AV33 CY7C1447AV33
(1 M × 36)
(2 M × 18)
(512 K × 72)
Instruction Field
Revision Number (31:29)
Device Depth (28:24)
Architecture/Memory
Type(23:18)[12]
Bus Width/Density(17:12)
Cypress JEDEC ID Code (11:1)
ID Register Presence Indicator (0)
Description
000
000
000
01011
01011
01011
Describes the version number.
000001
000001
000001
Defines memory type and architecture
100111
010111
110111
Defines width and density
00000110100
00000110100
00000110100
1
1
1
Reserved for Internal Use
Allows unique identification of SRAM
vendor.
Indicates the presence of an ID register.
Scan Register Sizes
Register Name
Instruction Bypass
Bit Size (× 36)
Bit Size (× 18)
Bit Size (× 18)
3
3
3
Bypass
1
1
1
ID
32
32
32
Boundary Scan Order (165-ball FBGA package)
89
89
–
Boundary Scan Order (209-ball FBGA package)
–
–
138
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures IO ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operations.
SAMPLE Z
010
Captures IO ring contents. Places the boundary scan register between TDI and TDO. Forces
all SRAM output drivers to a High Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures IO ring contents. Places the boundary scan register between TDI and TDO. Does not
affect SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Note
12. Bit #24 is “1” in the ID Register Definitions for both 2.5 V and 3.3 V versions of this device.
Document Number: 38-05357 Rev. *I
Page 18 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
165-ball FBGA Boundary Scan Order[13, 14]
CY7C1441AV33 (1 M × 36), CY7C1443AV33 (2 M × 18)
Bit #
Ball ID
Bit #
Ball ID
1
26
E11
N6
2
27
D11
N7
3
N10
28
G10
4
P11
29
F10
5
P8
30
E10
6
R8
31
D10
7
R9
32
C11
8
P9
33
A11
9
P10
34
B11
10
R10
35
A10
11
R11
36
B10
12
H11
37
A9
13
N11
38
B9
14
M11
39
C10
15
L11
40
A8
16
K11
41
B8
17
J11
42
A7
18
M10
43
B7
19
L10
44
B6
20
K10
45
A6
21
J10
46
B5
22
H9
47
A5
23
H10
48
A4
24
G11
49
B4
25
F11
50
B3
Bit #
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
Ball ID
A3
A2
B2
C2
B1
A1
C1
D1
E1
F1
G1
D2
E2
F2
G2
H1
H3
J1
K1
L1
M1
J2
K2
L2
M2
Bit #
76
77
78
79
80
81
82
83
84
85
86
87
88
89
Ball ID
N1
N2
P1
R1
R2
P3
R3
P2
R4
P4
N5
P6
R6
Internal
Notes
13. Balls which are NC (No Connect) are preset LOW.
14. Bit# 89 is preset HIGH.
Document Number: 38-05357 Rev. *I
Page 19 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Maximum Ratings
DC Input Voltage ................................ –0.5 V to VDD + 0.5 V
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage Temperature ............................... –65 C to +150 C
Ambient Temperature with
Power Applied ......................................... –55C to +125 C
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage ........................................ > 2001 V
(per MIL-STD-883, Method 3015)
Latch-up Current ................................................... > 200 mA
Operating Range
Supply Voltage on VDD Relative to GND .....–0.3 V to +4.6 V
Range
Supply Voltage on VDDQ Relative to GND .... –0.3 V to +VDD
Commercial
DC Voltage Applied to Outputs
in Tri-State ........................................–0.5 V to VDDQ + 0.5 V
Industrial
Ambient
Temperature
VDD
VDDQ
0 °C to +70 °C
3.3 V– 5% /
+ 10%
2.5 V – 5% to
VDD
–40 °C to +85 °C
Electrical Characteristics
Over the Operating Range[15, 16]
DC Electrical Characteristics
Over the Operating Range
Parameter
Description
VDD
Power Supply Voltage
VDDQ
IO Supply Voltage
VOH
VOL
VIH
VIL
Output HIGH Voltage
Output LOW Voltage
Input HIGH
Voltage[15]
Input LOW
Voltage[15]
Test Conditions
Min
Max
Unit
3.135
3.6
V
for 3.3 V IO
3.135
VDD
V
for 2.5 V IO
2.375
2.625
V
for 3.3 V IO, IOH = –4.0 mA
2.4
–
V
for 2.5 V IO, IOH = –1.0 mA
2.0
–
V
for 3.3 V IO, IOL = 8.0 mA
–
0.4
V
for 2.5 V IO, IOL = 1.0 mA
–
0.4
V
for 3.3 V IO
2.0
VDD + 0.3 V
V
for 2.5 V IO
1.7
VDD + 0.3 V
V
for 3.3 V IO
–0.3
0.8
V
for 2.5 V IO
–0.3
0.7
V
Input Leakage Current
except ZZ and MODE
GND  VI  VDDQ
–5
5
A
Input Current of MODE
Input = VSS
–30
–
A
Input = VDD
–
5
A
Input Current of ZZ
Input = VSS
–5
–
A
Input = VDD
–
30
A
IOZ
Output Leakage Current
GND  VI  VDDQ, Output Disabled
–5
5
A
IDD
VDD Operating Supply
Current
VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
7.5-ns cycle, 133 MHz
–
310
mA
10-ns cycle, 100 MHz
–
290
mA
IX
ISB1
Automatic CE Power down Max VDD, Device Deselected,
Current—TTL Inputs
VIN  VIH or VIN  VIL, f = fMAX,
inputs switching
All Speeds
–
180
mA
ISB2
All speeds
Automatic CE Power down Max VDD, Device Deselected,
Current—CMOS Inputs
VIN  VDD – 0.3 V or VIN  0.3 V,
f = 0, inputs static
–
120
mA
Notes
15. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2).
16. TPower-up: Assumes a linear ramp from 0 V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
Document Number: 38-05357 Rev. *I
Page 20 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Electrical Characteristics (continued)
Over the Operating Range[15, 16]
DC Electrical Characteristics (continued)
Over the Operating Range
Parameter
Description
Test Conditions
Min
Max
Unit
ISB3
Automatic CE Power down Max VDD, Device Deselected,
All Speeds
Current—CMOS Inputs
VIN  VDDQ – 0.3 V or VIN  0.3 V,
f = fMAX, inputs switching
–
180
mA
ISB4
Automatic CE Power down Max VDD, Device Deselected,
Current—TTL Inputs
VIN  VDD – 0.3 V or VIN  0.3 V,
f = 0, inputs static
–
135
mA
All Speeds
Capacitance
Parameter[17]
Description
CIN
Input Capacitance
CCLK
Clock Input Capacitance
CIO
Input/Output Capacitance
100-pin TQFP 165-ball FBGA 209-ball FBGA Unit
Max
Max
Max
Test Conditions
TA = 25 C, f = 1 MHz,
VDD = 3.3 V, VDDQ = 2.5 V
6.5
7
5
pF
3
7
5
pF
5.5
6
7
pF
Thermal Resistance
Parameter[17]
Description
JA
Thermal Resistance
(Junction to Ambient)
JC
Thermal Resistance
(Junction to Case)
100-pin TQFP 165-ball FBGA 209-ball FBGA Unit
Package
Package
Package
Test Conditions
Test conditions follow standard
test methods and procedures for
measuring thermal impedance,
per EIA/JESD51.
25.21
20.8
25.31
C/W
2.28
3.2
4.48
C/W
Figure 2. AC Test Loads and Waveforms
3.3 V IO Test Load
R = 317 
3.3 V
OUTPUT
OUTPUT
RL = 50 
Z0 = 50 
GND
5 pF
R = 351 
VT = 1.5 V
INCLUDING
JIG AND
SCOPE
(a)
ALL INPUT PULSES
VDDQ
10%
90%
10%
90%
 1 ns
 1 ns
(c)
(b)
2.5 V IO Test Load
R = 1667 
2.5 V
OUTPUT
OUTPUT
RL = 50 
Z0 = 50 
GND
5 pF
R = 1538 
VT = 1.25 V
(a)
ALL INPUT PULSES
VDDQ
INCLUDING
JIG AND
SCOPE
(b)
10%
90%
10%
90%
 1 ns
 1 ns
(c)
Note
17. Tested initially and after any design or process change that may affect these parameters.
Document Number: 38-05357 Rev. *I
Page 21 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Switching Characteristics
Over the Operating Range[18, 19]
Description
Parameter
tPOWER
VDD (Typical) to the first Access[20]
-133
-100
Unit
Min
Max
Min
Max
1
–
1
–
ms
Clock
tCYC
Clock Cycle Time
7.5
–
10
–
ns
tCH
Clock HIGH
2.5
–
3.0
–
ns
tCL
Clock LOW
2.5
–
3.0
–
ns
–
6.5
–
8.5
ns
Output Times
tCDV
Data Output Valid After CLK Rise
tDOH
Data Output Hold After CLK Rise
2.5
–
2.5
–
ns
tCLZ
Clock to Low Z[21, 22, 23]
2.5
–
2.5
–
ns
tCHZ
Clock to High
Z[21, 22, 23]
–
3.8
0
4.5
ns
tOEV
OE LOW to Output Valid
–
3.0
–
3.8
ns
Z[21, 22, 23]
tOELZ
OE LOW to Output Low
tOEHZ
OE HIGH to Output High Z[21, 22, 23]
0
–
0
–
ns
–
3.0
–
4.0
ns
Setup Times
tAS
Address Setup Before CLK Rise
1.5
–
1.5
–
ns
tADS
ADSP, ADSC Setup Before CLK Rise
1.5
–
1.5
–
ns
tADVS
ADV Setup Before CLK Rise
1.5
–
1.5
–
ns
tWES
GW, BWE, BWX Setup Before CLK Rise
1.5
–
1.5
–
ns
tDS
Data Input Setup Before CLK Rise
1.5
–
1.5
–
ns
tCES
Chip Enable Setup
1.5
–
1.5
–
ns
tAH
Address Hold After CLK Rise
0.5
–
0.5
–
ns
tADH
ADSP, ADSC Hold After CLK Rise
0.5
–
0.5
–
ns
tWEH
GW, BWE, BWX Hold After CLK Rise
0.5
–
0.5
–
ns
tADVH
ADV Hold After CLK Rise
0.5
–
0.5
–
ns
tDH
Data Input Hold After CLK Rise
0.5
–
0.5
–
ns
tCEH
Chip Enable Hold After CLK Rise
0.5
–
0.5
–
ns
Hold Times
Notes
18. Timing reference level is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V.
19. Test conditions shown in (a) of Figure 2 on page 21 unless otherwise noted.
20. This part has a voltage regulator internally; tPOWER is the time that the power must be supplied above VDD(minimum) initially, before a read or write operation can be
initiated.
21. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of Figure 2 on page 21. Transition is measured ± 200 mV from steady-state voltage.
22. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
High Z prior to Low Z under the same system conditions.
23. This parameter is sampled and not 100% tested.
Document Number: 38-05357 Rev. *I
Page 22 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Timing Diagrams
Figure 3. Read Cycle Timing[24]
tCYC
CLK
t
t ADS
CH
t CL
tADH
ADSP
t ADS
tADH
ADSC
t AS
tAH
A1
ADDRESS
A2
t
GW, BWE,BW
t
WES
WEH
X
t CES
Deselect Cycle
t CEH
CE
t
ADVS
t
ADVH
ADV
ADV suspends burst
OE
t OEV
t OEHZ
t CLZ
Data Out (Q)
High-Z
Q(A1)
t CDV
t OELZ
t CHZ
t DOH
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
t CDV
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
Burst wraps around
to its initial state
Single READ
BURST
READ
DON’T CARE
UNDEFINED
.
Note
24. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
Document Number: 38-05357 Rev. *I
Page 23 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Timing Diagrams (continued)
Figure 4. Write Cycle Timing[25, 26]
t CYC
CLK
t
t ADS
CH
t
CL
tADH
ADSP
t ADS
ADSC extends burst
tADH
t ADS
tADH
ADSC
t AS
tAH
A1
ADDRESS
A2
A3
Byte write signals are ignored for first cycle when
ADSP initiates burst
t WES tWEH
BWE,
BW
X
t
WES
t
WEH
GW
t CES
tCEH
CE
t ADVS tADVH
ADV
ADV suspends burst
OE
t
Data in (D)
High-Z
t
DS
t
DH
D(A1)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
OEHZ
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
DON’T CARE
Extended BURST WRITE
UNDEFINED
.
Notes
25. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
26. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BWX LOW
Document Number: 38-05357 Rev. *I
Page 24 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Timing Diagrams (continued)
Figure 5. Read/Write Cycle Timing[27, 28, 29]
tCYC
CLK
t
t ADS
CH
t
CL
tADH
ADSP
ADSC
t AS
ADDRESS
A1
tAH
A2
A3
A4
t
WES
t
A5
A6
WEH
BWE, BW X
t CES
tCEH
CE
ADV
OE
t DS
Data In (D)
Data Out (Q)
High-Z
t
OEHZ
Q(A1)
tDH
t OELZ
D(A3)
D(A5)
Q(A4)
Q(A2)
Back-to-Back READs
D(A6)
t CDV
Single WRITE
Q(A4+1)
BURST READ
DON’T CARE
Q(A4+2)
Q(A4+3)
Back-to-Back
WRITEs
UNDEFINED
.
Note
27. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
28. The data bus (Q) remains in high Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC.
29. GW is HIGH.
Document Number: 38-05357 Rev. *I
Page 25 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Timing Diagrams (continued)
Figure 6. ZZ Mode Timing[30, 31]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
30. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device.
31. DQs are in high Z when exiting ZZ sleep mode.
Document Number: 38-05357 Rev. *I
Page 26 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Ordering Information
Cypress offers other versions of this type of product in different configurations and features. The following table contains only the list
of parts that are currently available.
For a complete listing of all options, visit the Cypress website at www.cypress.com and refer to the product summary page at
http://www.cypress.com/products, or contact your local sales representative.
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
133
Ordering Code
Package
Diagram
Part and Package Type
CY7C1441AV33-133AXC
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
CY7C1441AV33-133AXI
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
CY7C1441AV33-133BZI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 × 17 × 1.4 mm)
CY7C1441AV33-133BZXI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 × 17 × 1.4 mm) Pb-free
Ordering Code Definitions
CY 7C 1441 A V33 - 133 XX X
X
Temperature Range: X = C or I
C = Commercial; I = Industrial
Pb-free
Package Type: XX = A or BZ
A = 100-pin TQFP
BZ = 165-ball FBGA
Frequency Range: 133 MHz
VDD = 3.3 V
Process Technology:  90 nm
1441 = FT, 1 Mb × 36 (36 Mb)
Marketing Code: 7C = SRAMs
Company ID: CY = Cypress
Document Number: 38-05357 Rev. *I
Page 27 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Package Diagrams
Figure 7. 100-pin TQFP (14 × 20 × 1.4 mm), 51-85050
51-85050 *D
Document Number: 38-05357 Rev. *I
Page 28 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Package Diagrams (continued)
Figure 8. 165-ball FBGA (15 × 17 × 1.4 mm), 51-85165
51-85165 *B
Document Number: 38-05357 Rev. *I
Page 29 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Package Diagrams (continued)
Figure 9. 209-ball FBGA (14 × 22 × 1.76 mm), 51-85167
51-85167 *A
Document Number: 38-05357 Rev. *I
Page 30 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Acronyms
Acronym
Document Conventions
Description
Units of Measure
CMOS
complementary metal oxide semiconductor
FBGA
fine-pitch ball grid array
°C
degree Celcius
I/O
input/output
µA
micro Amperes
JTAG
Joint Test Action Group
mA
milli Amperes
LSB
least significant bit
mm
milli meter
MSB
most significant bit
ms
milli seconds
Symbol
Unit of Measure
OE
output enable
MHz
Mega Hertz
SRAM
static random access memory
ns
nano seconds
TAP
test access port

ohms
TCK
test clock
%
percent
TDI
test data-in
pF
pico Farad
TDO
test data-out
V
Volts
TMS
test mode select
W
Watts
TQFP
thin quad flat pack
Document Number: 38-05357 Rev. *I
Page 31 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Document History Page
Document Title: CY7C1441AV33/CY7C1443AV33/CY7C1447AV33, 36-Mbit (1 M × 36/2 M × 18/512 K × 72) Flow-Through SRAM
Document Number: 38-05357
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
124459
03/06/03
CJM
New Data Sheet
*A
254910
See ECN
SYT
Part number changed from previous revision. New and old part number differ by
the letter “A”
Modified Functional Block diagrams
Modified switching waveforms
Added Footnote #13 (32-Bit Vendor I.D Code changed)
Added Boundary scan information
Added IDD, IX and ISB values in the DC Electrical Characteristics
Added tPOWER specifications in Switching Characteristics table
Removed 119 PBGA Package
Changed 165 FBGA Package from BB165C (15 x 17 x 1.20 mm) to BB165
(15 x 17 x 1.40 mm)
Changed 209-Lead PBGA BG209 (14 x 22 x 2.20 mm) to BB209A
(14 x 22 x 1.76 mm)
*B
300131
See ECN
SYT
Removed 150 and 117 MHz Speed Bins
Changed JA and JC from TBD to 25.21 and 2.58 C/W respectively for TQFP
Package on Pg # 21
Added lead-free information for 100-pin TQFP, 165 FBGA and 209 BGA
Packages.
Added comment of ‘Lead-free BG and BZ packages availability’ below the
Ordering Information
*C
320813
See ECN
SYT
Changed H9 pin from VSSQ to VSS on the Pin Configuration table for 209 FBGA
Changed the test condition from VDD = Min. to VDD = Max for VOL in the Electrical
Characteristics table.
Replaced the TBD’s for IDD, ISB1, ISB2, ISB3 and ISB4 to their respective values.
Replaced TBD’s for JA and JC to their respective values for 165 fBGA and 209
fBGA packages on the Thermal Resistance table.
Changed CIN,CCLK and CIO to 6.5, 3 and 5.5 pF from 5, 5 and 7 pF for TQFP
Package.
Removed “Lead-free BG and BZ packages availability” comment below the
Ordering Information
*D
331551
See ECN
SYT
Modified Address Expansion balls in the pinouts for 165 FBGA and 209 BGA
Packages as per JEDEC standards and updated the Pin Definitions accordingly
Modified VOL, VOH test conditions
Replaced TBD to 100 mA for IDDZZ
Changed CIN, CCLK and CIO to 7, 7and 6 pF from 5, 5 and 7 pF for 165 FBGA
Package.
Added Industrial Temperature Grade
Changed ISB2 and ISB4 from 100 and 110 mA to 120 and 135 mA respectively
Updated the Ordering Information by shading and unshading MPNs as per availability
Document Number: 38-05357 Rev. *I
Page 32 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Document History Page (continued)
Document Title: CY7C1441AV33/CY7C1443AV33/CY7C1447AV33, 36-Mbit (1 M × 36/2 M × 18/512 K × 72) Flow-Through SRAM
Document Number: 38-05357
REV.
ECN NO.
Issue Date
Orig. of
Change
*E
417547
See ECN
RXU
Converted from Preliminary to Final.
Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901
North First Street” to “198 Champion Court”.
Changed IX current value in MODE from –5 & 30 A to –30 & 5 A respectively
and also Changed IX current value in ZZ from –30 & 5 A to –5 & 30 A respectively on page# 19.
Modified test condition in note# 8 from VIH < VDD to VIH VDD.
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the
Electrical Characteristics Table.
Replaced Package Name column with Package Diagram in the Ordering
Information table.
Replaced Package Diagram of 51-85050 from *A to *B
Updated the Ordering Information.
*F
473650
See ECN
VKN
Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND.
Changed tTH, tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP AC
Switching Characteristics table.
Updated the Ordering Information table.
*G
2447027
See ECN
*H
2898501
03/24/2010
NJY
Removed inactive part numbers from Ordering Information table; Updated
package diagrams.
*I
3263570
05/23/2011
OSN
Adeed Ordering Code Definitions.
Updated Package Diagrams.
Added Acronyms and Units of Measure.
Updated in new template.
Document Number: 38-05357 Rev. *I
Description of Change
VKN/AESA Corrected typo in the Ordering Information table
Corrected typo in the CY7C1447AV33 ‘s Logic Block diagram
Updated the x72 block diagram
Page 33 of 34
[+] Feedback
CY7C1441AV33
CY7C1443AV33, CY7C1447AV33
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
Clocks & Buffers
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
cypress.com/go/memory
Optical & Image Sensing
cypress.com/go/image
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2003-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 38-05357 Rev. *I
Revised May 23, 2011
Page 34 of 34
i486 is a trademark, and Intel and Pentium are registered trademarks of Intel Corporation. PowerPC is a trademark of IBM Corporation. All products and company names mentioned in this document
may be the trademarks of their respective holders.
[+] Feedback