CY7C1049CV33 4-Mbit (512K x 8) Static RAM Functional Description[1] Features • Temperature Ranges The CY7C1049CV33 is a high-performance CMOS Static RAM organized as 524,288 words by 8 bits. Easy memory expansion is provided by an active LOW Chip Enable (CE), an active LOW Output Enable (OE), and three-state drivers. Writing to the device is accomplished by taking Chip Enable (CE) and Write Enable (WE) inputs LOW. Data on the eight I/O pins (I/O0 through I/O7) is then written into the location specified on the address pins (A0 through A18). — Commercial: 0°C to 70°C — Industrial: –40°C to 85°C — Automotive: –40°C to 125°C • High speed — tAA = 10 ns • Low active power — 324 mW (max.) Reading from the device is accomplished by taking Chip Enable (CE) and Output Enable (OE) LOW while forcing Write Enable (WE) HIGH. Under these conditions, the contents of the memory location specified by the address pins will appear on the I/O pins. • 2.0V data retention • Automatic power-down when deselected • TTL-compatible inputs and outputs • Easy memory expansion with CE and OE features The eight input/output pins (I/O0 through I/O7) are placed in a high-impedance state when the device is deselected (CE HIGH), the outputs are disabled (OE HIGH), or during a Write operation (CE LOW, and WE LOW). The CY7C1049CV33 is available in standard 400-mil-wide 36-pin SOJ package and 44-pin TSOP II package with center power and ground (revolutionary) pinout. Logic Block Diagram Pin Configuration SOJ Top View I/O0 INPUT BUFFER CE I/O1 I/O2 SENSE AMPS ROW DECODER A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 512K x 8 ARRAY I/O3 I/O4 I/O5 COLUMN DECODER I/O6 POWER DOWN I/O7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 NC A18 A17 A16 A15 OE I/O7 I/O6 GND VCC I/O5 I/O4 A14 A13 A12 A11 A10 NC NC NC A0 A1 A2 A3 A4 CE I/O0 I/O1 VCC VSS I/O2 I/O3 WE A5 A6 A7 A8 A9 NC NC 1 44 2 3 43 42 4 41 40 39 38 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC NC NC A18 A17 A16 A15 OE I/O7 I/O6 VSS VCC I/O5 I/O4 A14 A13 A12 A11 A10 NC NC NC A 11 A 12 A 13 A 14 A 15 A 16 A17 A18 WE OE A0 A1 A2 A3 A4 CE I/O0 I/O1 VCC GND I/O2 I/O3 WE A5 A6 A7 A8 A9 TSOP II Top View Notes: 1. For guidelines on SRAM system design, please refer to the System Design Guidelines Cypress application note, available on the internet at www.cypress.com. Cypress Semiconductor Corporation Document #: 38-05006 Rev. *E • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised March 29, 2005 CY7C1049CV33 Selection Guide -8 Maximum Access Time Maximum Operating Current -10 -12 -15 -20 Unit 8 10 12 15 20 ns Commercial 100 90 85 80 80 mA Industrial 110 100 95 90 90 mA - - - 95 - mA 10 10 10 10 10 mA - - - 15 - mA Automotive Maximum CMOS Standby Current Commercial / Industrial Automotive Shaded areas contain advance information. Pin Definitions Pin Name A0–A18 36-SOJ Pin Number 44 TSOP-II Pin Number 1–5,14–18, 3–7,16–20, 20–24,32–35 26–30,38–41 I/O Type Input Description Address Inputs used to select one of the address locations. I/O0–I/O7 7,8,11,12,25, 26,29,30 9,10,13,14, 31,32,35,36 Input/Output Bidirectional Data I/O lines. Used as input or output lines depending on operation NC[2] 19,36 1,2,21,22,23, 24,25,42,43, 44 No Connect WE 13 15 Input/Control Write Enable Input, active LOW. When selected LOW, a WRITE is conducted. When selected HIGH, a READ is conducted. CE 6 8 Input/Control Chip Enable Input, active LOW. When LOW, selects the chip. When HIGH, deselects the chip. OE 31 37 Input/Control Output Enable, active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. VSS, GND 10,28 12,34 VCC 9,27 11,33 Ground No Connects. This pin is not connected to the die Ground for the device. Should be connected to ground of the system. Power Supply Power Supply inputs to the device. Notes: 2. NC pins are not connected on the die. Document #: 38-05006 Rev. *E Page 2 of 11 CY7C1049CV33 Input Voltage[3] ...................................... –0.5V to VCC + 0.5V Maximum Ratings Current into Outputs (LOW)......................................... 20 mA (Above which the useful life may be impaired. For user guidelines, not tested.) Operating Range Storage Temperature ................................. –65°C to +150°C Range Ambient Temperature with Power Applied............................................. –55°C to +125°C Ambient Temperature VCC 0°C to +70°C 3.3V ± 0.3V Commercial Supply Voltage on VCC to Relative GND[3] –0.5V to +4.6VDC Industrial –40°C to +85°C Automotive –40°C to +125°C Voltage Applied to Outputs in High-Z State[3] ....................................–0.5V to VCC + 0.5V Electrical Characteristics Over the Operating Range -8 Parameter Description Test Conditions Min. -10 Max. 2.4 Min. -12 Max. Min. VOH Output HIGH Voltage VCC = Min.; IOH = –4.0 mA 2.4 VOL Output LOW Voltage VCC = Min.,; IOL = 8.0 mA VIH Input HIGH Voltage 2.0 VCC + 0.3 2.0 VCC + 0.3 VIL Input LOW Voltage[3] –0.3 0.8 –0.3 IIX Input Load Current GND < VI < VCC Com’l/Ind’l –1 +1 IOZ Output Leakage Current GND < VOUT < VCC, Output Disabled Com’l/Ind’l –1 +1 ICC VCC Operating Supply Current VCC = Max., f = fMAX = 1/tRC Com’l 100 Ind’l ISB1 Automatic CE Power-down Current —TTL Inputs Max. VCC, CE > VIH; VIN > VIH or VIN < VIL, f = fMAX Com’l/Ind’l ISB2 Automatic CE Power-down Current —CMOS Inputs Max. VCC, CE > VCC – 0.3V, VIN > VCC – 0.3V, or VIN < 0.3V, f = 0 Com’l/Ind’l 0.4 Max. 2.4 0.4 Unit V 0.4 V 2.0 VCC + 0.3 V 0.8 –0.3 0.8 V –1 +1 –1 +1 µA –1 +1 –1 +1 µA 90 85 mA 110 100 95 mA 40 40 40 mA 10 10 10 mA Electrical Characteristics Over the Operating Range -15 Parameter Description Test Conditions VOH Output HIGH Voltage VCC = Min.; IOH = –4.0 mA VOL Output LOW Voltage VCC = Min.,; IOL = 8.0 mA VIH Input HIGH Voltage Input LOW IIX Input Load Current IOZ ICC GND < VI < VCC Output Leakage Current GND < VOUT < VCC, Output Disabled VCC Operating Supply Current VCC = Max., f = fMAX = 1/tRC Max. 2.4 Min. Max. Unit 0.4 V 2.4 0.4 Voltage[3] VIL Min. -20 V 2.0 VCC + 0.3 2.0 VCC + 0.3 V –0.3 0.8 –0.3 0.8 V Com’l / Ind’l –1 +1 –1 +1 µA Automotive –20 +20 - - µA Com’l / Ind’l –1 +1 –1 +1 µA Automotive –20 +20 - - µA Com’l 80 80 mA Ind’l 90 90 mA Automotive 95 - mA Note: 3. VIL (min.) = –2.0V and VIH(max) = VCC + 0.5V for pulse durations of less than 20 ns. Document #: 38-05006 Rev. *E Page 3 of 11 CY7C1049CV33 Electrical Characteristics Over the Operating Range (continued) -15 Parameter ISB1 ISB2 Description Test Conditions Min. -20 Max. Min. Max. Unit Automatic CE Power-down Current —TTL Inputs Max. VCC, CE > VIH; VIN > VIH or VIN < VIL, f = fMAX Com’l / Ind’l 40 40 mA Automotive 45 - mA Automatic CE Power-down Current —CMOS Inputs Max. VCC, CE > VCC – 0.3V, VIN > VCC – 0.3V, or VIN < 0.3V, f = 0 Com’l/Ind’l 10 10 mA Automotive 15 - mA Thermal Resistance[4] Parameter ΘJA ΘJC Description 36-pin SOJ 36-pin SOJ 44-TSOP-II 44-TSOP-II (Non Pb-Free) (Pb-Free) (Non Pb-Free) (Pb-Free) Unit Test Conditions Thermal Resistance (Junction to Ambient) Thermal Resistance (Junction to Case) Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA / JESD51. 46.51 46.51 41.66 41.66 °C/W 18.8 18.8 10.56 10.56 °C/W Capacitance[4] Parameter Description CIN Input Capacitance COUT I/O Capacitance Test Conditions Max. Unit 8 pF 8 pF TA = 25°C, f = 1 MHz, VCC = 3.3V AC Test Loads and Waveforms[5] 12-, 15-, 20-ns devices: 8-, 10-ns devices: Z = 50Ω 50Ω * CAPACITIVE LOAD CONSISTS OF ALL COMPONENTS OF THE TEST ENVIRONMENT 30 pF* OUTPUT R2 351Ω 30 pF 1.5V (a) (b) High-Z characteristics: ALL INPUT PULSES 3.0V 90% GND 10% (c) R 317Ω 3.3V 90% 10% Rise Time: 1 V/ns R 317Ω 3.3V OUTPUT Fall Time: 1 V/ns OUTPUT R2 351Ω 5 pF (d) Notes: 4. Tested initially and after any design or process changes that may affect these parameters. 5. AC characteristics (except High-Z) for all 8-ns and 10-ns parts are tested using the load conditions shown in Figure (a). All other speeds are tested using the Thevenin load shown in Figure (b). High-Z characteristics are tested for all speeds using the test load shown in Figure (d). Document #: 38-05006 Rev. *E Page 4 of 11 CY7C1049CV33 AC Switching Characteristics Over the Operating Range [6] -8 Parameter Description Min. -10 Max. Min. -12 Max. Min. Max. Unit Read Cycle tpower[7] VCC(typical) to the first access 1 tRC Read Cycle Time 8 tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE LOW to Data Valid tDOE OE LOW to Data Valid tLZOE OE LOW to Low-Z tHZOE OE HIGH to CE LOW to tHZCE CE HIGH to High-Z[8, 9] tPU CE LOW to Power-up tPD Write Cycle 10 12 12 3 3 8 5 0 6 ns 6 3 3 4 6 0 0 8 ns ns 5 0 ns ns 5 3 12 0 4 ns ns 10 4 CE HIGH to Power-down ns 10 3 High-Z[8, 9] µs 1 8 0 Low-Z[9] tLZCE 1 ns ns 10 12 ns [10, 11] tWC Write Cycle Time 8 10 12 ns tSCE CE LOW to Write End 6 7 8 ns tAW Address Set-up to Write End 6 7 8 ns tHA Address Hold from Write End 0 0 0 ns tSA Address Set-up to Write Start 0 0 0 ns tPWE WE Pulse Width 6 7 8 ns tSD Data Set-up to Write End 4 5 6 ns tHD Data Hold from Write End 0 0 0 ns Low-Z[9] tLZWE WE HIGH to tHZWE WE LOW to High-Z[8, 9] 3 3 3 4 ns 5 6 ns Max. Unit Shaded areas contain advance information. AC Switching Characteristics Over the Operating Range [6] -15 Parameter Description Min. -20 Max. Min. Read Cycle µs tpower[7] VCC(typical) to the first access 1 tRC Read Cycle Time 15 tAA Address to Data Valid 15 20 ns tOHA Data Hold from Address Change 3 3 ns tACE CE LOW to Data Valid 15 20 ns tDOE OE LOW to Data Valid 7 8 ns 1 20 ns Notes: 6. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V. 7. tPOWER gives the minimum amount of time that the power supply should be at stable, typical VCC values until the first memory access can be performed. 8. tHZOE, tHZCE, and tHZWE are specified with a load capacitance of 5 pF as in part (d) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage. 9. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device. 10. The internal Write time of the memory is defined by the overlap of CE LOW, and WE LOW. CE and WE must be LOW to initiate a Write, and the transition of either of these signals can terminate the Write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the Write. 11. The minimum Write cycle time for Write Cycle No. 3 (WE controlled, OE LOW) is the sum of tHZWE and tSD. Document #: 38-05006 Rev. *E Page 5 of 11 CY7C1049CV33 AC Switching Characteristics Over the Operating Range (continued)[6] -15 Parameter Description tLZOE OE LOW to Low-Z tHZOE OE HIGH to High-Z[8, 9] Max. 0 CE LOW to Low-Z CE HIGH to High-Z tPU CE LOW to Power-up tPD CE HIGH to Power-down Max. 0 3 [8, 9] tHZCE Min. 7 [9] tLZCE Write Cycle Min. -20 ns 8 3 7 0 ns ns 8 0 15 Unit ns ns 20 ns [10, 11] tWC Write Cycle Time 15 20 ns tSCE CE LOW to Write End 10 10 ns tAW Address Set-up to Write End 10 10 ns tHA Address Hold from Write End 0 0 ns tSA Address Set-up to Write Start 0 0 ns tPWE WE Pulse Width 10 10 ns tSD Data Set-up to Write End 7 8 ns tHD Data Hold from Write End 0 0 ns 3 3 ns tLZWE tHZWE WE HIGH to Low-Z[9] WE LOW to High-Z[8, 9] 7 8 ns Switching Waveforms Read Cycle No. 1[12, 13] tRC ADDRESS tAA tOHA DATA OUT PREVIOUS DATA VALID DATA VALID Notes: 12. Device is continuously selected. OE, CE = VIL. 13. WE is HIGH for Read cycle. Document #: 38-05006 Rev. *E Page 6 of 11 CY7C1049CV33 Switching Waveforms (continued) Read Cycle No. 2 (OE Controlled)[13, 14] ADDRESS tRC CE tACE OE tHZOE tDOE DATA OUT tHZCE tLZOE HIGH IMPEDANCE DATA VALID tLZCE tPD tPU VCC SUPPLY CURRENT HIGH IMPEDANCE ICC 50% 50% ISB Write Cycle No. 1(WE Controlled, OE HIGH During Write)[15, 16] tWC ADDRESS tSCE CE tAW tSA tHA tPWE WE OE tSD DATA I/O tHD DATAIN VALID NOTE 17 tHZOE Notes: 14. Address valid prior to or coincident with CE transition LOW. 15. Data I/O is high-impedance if OE = VIH. 16. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state. 17. During this period the I/Os are in the output state and input signals should not be applied. Document #: 38-05006 Rev. *E Page 7 of 11 CY7C1049CV33 Switching Waveforms (continued) Write Cycle No. 2 (WE Controlled, OE LOW)[16] tWC ADDRESS tSCE CE tAW tSA tHA tPWE WE tSD DATA I/O NOTE 17 DATA VALID tHZWE Document #: 38-05006 Rev. *E tHD tLZWE Page 8 of 11 CY7C1049CV33 Truth Table CE OE WE I/O0–I/O7 Mode Power H X X High-Z Power-down Standby (ISB) L L H Data Out Read Active (ICC) L X L Data In Write Active (ICC) L H H High-Z Selected, Outputs Disabled Active (ICC) Ordering Information Speed (ns) 10 12 15 20 10 12 15 20 Ordering Code Package Name Package Type Operating Range CY7C1049CV33-10VC V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-10ZC Z44 44-pin TSOP II Commercial CY7C1049CV33-10VI V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-10ZI Z44 44-pin TSOP II CY7C1049CV33-12VC V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-12ZC Z44 44-pin TSOP II CY7C1049CV33-12VI V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-12ZI Z44 44-pin TSOP II CY7C1049CV33-15VC V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-15ZC Z44 44-pin TSOP II CY7C1049CV33-15VI V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-15ZI Z44 44-pin TSOP II CY7C1049CV33-15VE V36 36-lead (400-Mil) Molded SOJ CY7C1049CV33-15ZSE Z44 44-pin TSOP II CY7C1049CV33-20VC V36 36-lead (400-Mil) Molded SOJ Commercial CY7C1049CV33-20VI V36 36-lead (400-Mil) Molded SOJ Industrial CY7C1049CV33-10VXC V36 36-lead (400-Mil) Molded SOJ (Pb-Free) CY7C1049CV33-10ZXC Z44 44-pin TSOP II (Pb-Free) Industrial Commercial Industrial Commercial Industrial Automotive Commercial CY7C1049CV33-10VXI V36 36-lead (400-Mil) Molded SOJ (Pb-Free) Industrial CY7C1049CV33-10ZXI Z44 44-pin TSOP II (Pb-Free) Industrial CY7C1049CV33-12VXC V36 36-lead (400-Mil) Molded SOJ (Pb-Free) CY7C1049CV33-12ZXC Z44 44-pin TSOP II (Pb-Free) CY7C1049CV33-12VXI V36 36-lead (400-Mil) Molded SOJ (Pb-Free) CY7C1049CV33-12ZXI Z44 44-pin TSOP II (Pb-Free) CY7C1049CV33-15VXC V36 36-lead (400-Mil) Molded SOJ (Pb-Free) CY7C1049CV33-15ZXC Z44 44-pin TSOP II (Pb-Free) CY7C1049CV33-15VXI V36 36-lead (400-Mil) Molded SOJ (Pb-Free) CY7C1049CV33-15ZXI Z44 44-pin TSOP II (Pb-Free) CY7C1049CV33-15VXE V36 36-lead (400-Mil) Molded SOJ (Pb-Free) Automotive CY7C1049CV33-15ZSXE Z44 44-pin TSOP II Automotive CY7C1049CV33-20VXC V36 36-lead (400-Mil) Molded SOJ (Pb-Free) Commercial CY7C1049CV33-20VXI V36 36-lead (400-Mil) Molded SOJ (Pb-Free) Industrial Commercial Industrial Commercial Industrial Shaded areas contain advance information. Please contact your local Cypress Sales representative for availability of these parts. Document #: 38-05006 Rev. *E Page 9 of 11 CY7C1049CV33 Package Diagrams 36-Lead (400-Mil) Molded SOJ V36 51-85090-*B 44-pin TSOP II Z44 51-85087-*A All products and company names mentioned in this document may be the trademarks of their respective holders. Document #: 38-05006 Rev. *E Page 10 of 11 © Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. CY7C1049CV33 Document History Page Document Title: CY7C1049CV33 4-Mbit (512K x 8) Static RAM Document Number: 38-05006 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 112569 03/06/02 HGK New data sheet *A 114091 04/25/02 DFP Changed Tpower unit from ns to µs *B 116479 09/16/02 CEA Add applications foot note to data sheet, page 1. *C 262949 See ECN RKF Added Automotive Specs Added ΘJA and ΘJC values on Page #3. *D 300091 See ECN RKF Added -20-ns Speed bin *E 344595 See ECN SYT Added Pb-Free package on page #8 Removed shading for CY7C1049CV33-15ZSXE in the ordering Information on page 9 Document #: 38-05006 Rev. *E Page 11 of 11