ZETTLER AZ764-1AH-12A

AZ764
16 A SPDT MINIATURE
POWER RELAY
FEATURES
•
•
•
•
•
•
•
•
Dielectric strength 5000 Vrms
Low height: 15.7 mm
Epoxy sealed version available
16 Amp switching (High inrush version 80A available)
AC and DC coils
Isolation spacing greater than 10 mm
Proof tracking index (PTI/CTI) 250
Reinforced insulation, EN 60730-1 (VDE 0631, part 1)
EN 60335-1 (VDE 0700, part 1)
• UL, CUR file E43203
• VDE file 40012572
CONTACTS
GENERAL DATA
Arrangement
SPDT (1 Form C)
SPST (1 Form A)
Ratings
Resistive load:
Max. switched power: 480 W or 4000 VA
Max. switched current: 16 A
Max. switched voltage: 300 VDC* or 400 VAC
Life Expectancy
Mechanical
Electrical
Minimum operations
3 x 107
7 x 104 at 16 A 250 VAC res.
Operate Time (typical)
7 ms at nominal coil voltage
Release Time (typical)
3 ms at nominal coil voltage
(with no coil suppression)
* Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
Rated Load
UL, CUR
16 A at 250 VAC General Use
VDE
16 A at 250 VAC
Material
Silver cadmium oxide, silver nickel
or silver tin oxide
Resistance
< 100 milliohms initially
COIL
Dielectric Strength
5000 Vrms coil to contact
(at sea level for 1 min.) 2500 Vrms between contact sets
1000 Vrms between open contacts
Insulation
Resistance
105 megohms min. at 500 VDC,
20°C, 50% RH
Insulation
(according to
DIN VDE 0110,
IEC 60664-1)
B250 at 1 Form C, flux proof version
C250 at other relay versions
Overvoltage category: III
Pollution degree: 3
Nominal voltage: 250 VAC
Dropout DC coils
AC coils
Ambient Temperature
Operating
Greater than 10% of nominal coil voltage
Greater than 15% of nominal coil voltage
At nominal coil voltage
-40°C (-40°F) to 85°C (185°F) - DC coils
-40°C (-40°F) to 70°C (158°F) - AC coils
-40°C (-40°F) to 105°C (221°F)
Storage
Power
At Pickup Voltage
(typical)
200 mW (DC coil)
.422 VA (AC coil)
Vibration
Break contacts: 5 g at 20…500 Hz
Make contacts: 20 g at 30…500 Hz
Max. Continuous
Dissipation
1.7 W at 20°C (68°F) ambient
1.7 VA at 20°C (68°F) ambient
Shock
20 g
Temperature Rise
26°C (47°F) at nominal coil voltage
Enclosure
P.B.T. polyester, UL-94 : V0
155°C (311°F)
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
Max. Immersion Time
30 seconds
Weight
14 grams
Packing unit in pcs
20 per carton tube / 1000 per carton box
Max. Temperature
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
ZETTLER
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2005-08-04
AZ764
RELAY ORDERING DATA
COIL SPECIFICATIONS - DC COIL
Nominal Coil
VDC
Must Operate
VDC
ORDER NUMBER*
Max. Continuous
VDC
Coil Resistance
Ohm ± 10%
1 Form A
1 Form C
AZ764–1CH–3D
3
2.1
7.6
22
AZ764–1AH–3D
5
3.5
12.7
60
AZ764–1AH–5D
AZ764–1CH–5D
6
4.2
15.3
90
AZ764–1AH–6D
AZ764–1CH–6D
9
6.3
22.9
200
AZ764–1AH–9D
AZ764–1CH–9D
12
8.4
30.6
360
AZ764–1AH–12D
AZ764–1CH–12D
18
12.6
45.9
710
AZ764–1AH–18D
AZ764–1CH–18D
24
16.8
61.2
1,440
AZ764–1AH–24D
AZ764–1CH–24D
36
25.2
92.0
3,140
AZ764–1AH–36D
AZ764–1CH–36D
48
33.6
122.0
5,700
AZ764–1AH–48D
AZ764–1CH–48D
60
42.0
153.0
7,500
AZ764–1AH–60D
AZ764–1CH–60D
110
77.0
280.0
25,200
AZ764–1AH–110D
AZ764–1CH–110D
COIL SPECIFICATIONS - AC COIL
Nominal Coil
VAC
Must Operate
VAC
Max. Continuous
VAC
ORDER NUMBER*
Nominal Current
mA ± 10%
Coil Resistance
Ohm ± 10%
1 Form A
1 Form C
12
9.0
18.0
63.0
100
AZ764–1AH–12A
AZ764–1CH–12A
24
18.0
36.0
31.3
400
AZ764–1AH–24A
AZ764–1CH–24A
48
36.0
72.0
15.6
1,550
AZ764–1AH–48A
AZ764–1CH–48A
60
45.0
90.0
12.5
2,600
AZ764–1AH–60A
AZ764–1CH–60A
110
82.5
165.0
6.8
8,900
AZ764–1AH–110A
AZ764–1CH–110A
115
86.3
172.5
6.5
9,600
AZ764–1AH–115A
AZ764–1CH–115A
120
90.0
180.0
6.3
10,200
AZ764–1AH–120A
AZ764–1CH–120A
220
165.0
330.0
3.4
35,500
AZ764–1AH–220A
AZ764–1CH–220A
230
172.5
345.0
3.3
38,500
AZ764–1AH–230A
AZ764–1CH–230A
240
180.0
360.0
3.1
42,500
AZ764–1AH–240A
AZ764–1CH–240A
* “1AH” or “1CH” denote silver cadmium oxide contacts.
Substitue “E” for “H” at “1AH” or “1CH” for silver tin oxide contacts.
Remove the “H” at “1AH” or “1CH” for silver nickel contacts.
Add suffix “E” at the end of order number for sealed version.
Substitue “1AT” for “1AH” for high inrush 80A silver tin
oxide contacts (available on 1 Form A and DC coils only).
DC - Coil operating range
3,0
3,0
2,8
2,8
2,6
2,6
I N = 16 A
2,4
UB / U N
UB / U N
AC - Coil operating range
1
2,2
2
2,0
2,2
2,0
3
1,8
2,4
1,6
1,6
1,4
1,4
1,2
1,2
1,0
0,6
10
20
30
3
40
50
60
B
0,8
A
0
1
1,0
B
0,8
I N = 16 A
1,8
70
80
90
100
0,6
0
10
20
Ambient temperature [°C]
A - Cold coil ( Tcoil = Tambient)
B - Hot coil (1,1 x UN), contact load = IN
ZETTLER
1 - no load on contacts
2 - half of rated load on contacts
3 - rated load on contacts
30
40
50
60
70
80
90
100
Ambient temperature [°C]
B - Hot coil (1,1 x UN), contact load = IN
1 - no load on contacts
3 - rated load on contacts
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2005-08-04
AZ764
MECHANICAL DATA
PC BOARD LAYOUT
.197
[5.0]
0.500 Max.
[12.7]
1.142 Max.
[29.0]
.60
[15.12]
.197
[5.0]
.098
[2.5]
*
.295
[7.5]
.618 Max.
[15.7]
*
2 x ø .040
[ø 1.0]
6 x ø .050
[ø 1.3]
* Not used on 1 Form A relay
.295
[7.5]
.154
[3.9]
Viewed toward terminals
WIRING DIAGRAMS
6 x .020
[0.5]
2 x ø .024
[ø 0.6]
1 Form C
.197
[5.0]
.197
[5.0]
.60
[15.12]
4
5
.295
[7.5]
6 x .035
[0.9]
1 Form A
3
2
4
5
2
.098
[2.5]
8
7
6
1
8
7
1
Viewed toward terminals
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
ACCESSORIES
For P.C.B. mount:
Socket EC 50
Retaining Clip MP 16 / MH 16
For DIN rail mount:
Socket ES 50
Retaining Clip MS 16
MECHANICAL DATA
EC 50
MP 16 / MH 16
ES 50
h = 15 ... 16.5 mm
h = 15 ... 16.5 mm
ZETTLER
MS 16
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2005-08-04
AZ764
Electrical life at 250 VAC, resistive load
Electrical life reduction factor at inductive AC load
107
F
1,0
Reduction factor
Number of cycles
0,9
106
0,8
0,7
0,6
0,5
105
0,4
0,3
1,0
0,9
0,8
0,7
0,6
0,5
0,4
0,3
cos j
0,2
Power factor
104
0
0,4
0,8
1,2
1,6
2,0
2,4
2,8
3,2
3,6
4,0
Ncos j = N x F
Breaking capacity [kVA]
Max. DC resistive load breaking capacity
DC current [A]
50
16
10
5
2
1
0,5
0,1
10
20
30
40 50
100
200
300
DC voltage [V]
ZETTLER
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2005-08-04