AD AD8191A

4:1 HDMI/DVI Switch with Equalization
AD8191A
FUNCTIONAL BLOCK DIAGRAM
PARALLEL
SERIAL
I2C_SDA
I2C_SCL
I2C_ADDR[2:0]
2
3
RESET
AD8191A
2
CONFIG
INTERFACE
AVCC
DVCC
AMUXVCC
AVEE
DVEE
CONTROL
LOGIC
VTTI
+
IP_A[3:0]
IN_A[3:0] –
+
IP_B[3:0]
IN_B[3:0] –
+
IP_C[3:0]
IN_C[3:0] –
+
IP_D[3:0]
IN_D[3:0] –
VTTO
4
4
4
4
4
4
SWITCH
CORE
EQ
+ OP[3:0]
– ON[3:0]
4
4
HIGH SPEED
VTTI
AUX_A[3:0]
AUX_B[3:0]
AUX_C[3:0]
AUX_D[3:0]
4
4
PE
BUFFERED
4
4
4
SWITCH
CORE
4
4
LOW SPEED
UNBUFFERED
AUX_COM[3:0]
07013-001
4 inputs, one output HDMI/DVI link
Pin-to-pin compatible with the AD8197A
4 TMDS channels per link
Supports 250 Mbps to 1.65 Gbps data rates
Supports 25 MHz to 165 MHz pixel clocks
Equalized inputs for operation with long HDMI cables
(20 meters at 1080p)
Fully buffered unidirectional inputs/outputs
Globally switchable, 50 Ω on-chip terminations
Pre-emphasized outputs
Low added jitter
Single-supply operation (3.3 V)
4 auxiliary channels per link
Bidirectional unbuffered inputs/outputs
Flexible supply operation (3.3 V to 5 V)
HDCP standard compatible
Allows switching of DDC bus and 2 additional signals
Output disable feature
Reduced power dissipation
Removable output termination
Allows building of larger arrays
Two AD8191As support HDMI/DVI dual link
Standards compatible: HDMI receiver, DVI, HDCP
Serial (I2C slave) and parallel control interface
100-lead, 14 mm × 14 mm LQFP, Pb-free package
PP_CH[1:0]
PP_OTO
PP_OCL
PP_EQ
PP_EN
PP_PRE[1:0]
FEATURES
BIDIRECTIONAL
Figure 1.
TYPICAL APPLICATION
GAME CONSOLE
MEDIA CENTER
HDTV SET
APPLICATIONS
SET-TOP BOX
DVD PLAYER
AD8191A
01:18
07013-002
Multiple input displays
Projectors
A/V receivers
Set-top boxes
Advanced television (HDTV) sets
HDMI
RECEIVER
Figure 2. Typical HDTV Application
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD8191A is an HDMI™/DVI switch featuring equalized
TMDS® inputs and pre-emphasized TMDS outputs, ideal for
systems with long cable runs. Outputs can be set to a high
impedance state to reduce the power dissipation and/or to allow
the construction of larger arrays using the wire-OR technique.
1. Supports data rates up to 1.65 Gbps, enabling 1080p HDMI
formats and UXGA (1600 × 1200) DVI resolutions.
The AD8191A is provided in a 100-lead LQFP, Pb-free, surfacemount package specified to operate over the −40°C to +85°C
temperature range.
3. Auxiliary switch routes a DDC bus and two additional
signals for a single-chip, HDMI 1.2a receive-compliant
solution.
2. Input cable equalizer enables use of long cables at the input
(more than 20 meters of 24 AWG cable at 1080p).
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
AD8191A
TABLE OF CONTENTS
Features .............................................................................................. 1
Switching/Update Delay............................................................ 16
Applications....................................................................................... 1
Parallel Control Interface .............................................................. 17
Functional Block Diagram .............................................................. 1
Serial Interface Configuration Registers ..................................... 18
Typical Application........................................................................... 1
High Speed Device Modes Register......................................... 18
General Description ......................................................................... 1
Auxiliary Device Modes Register............................................. 18
Product Highlights ........................................................................... 1
Receiver Settings Register ......................................................... 19
Revision History ............................................................................... 2
Input Termination Pulse Register 1 and Register 2 ............... 19
Specifications..................................................................................... 3
Receive Equalizer Register 1 and Register 2 ........................... 19
Absolute Maximum Ratings............................................................ 5
Transmitter Settings Register.................................................... 19
Thermal Resistance ...................................................................... 5
Parallel Interface Configuration Registers .................................. 20
Maximum Power Dissipation ..................................................... 5
High Speed Device Modes Register......................................... 20
ESD Caution.................................................................................. 5
Auxiliary Device Modes Register............................................. 20
Pin Configuration and Function Descriptions............................. 6
Receiver Settings Register ......................................................... 20
Typical Performance Characteristics ............................................. 9
Input Termination Pulse Register 1 and Register 2 ............... 21
Theory of Operation ...................................................................... 13
Receive Equalizer Register 1 and Register 2 ........................... 21
Introduction ................................................................................ 13
Transmitter Settings Register.................................................... 21
Input Channels............................................................................ 13
Applications Information .............................................................. 22
Output Channels ........................................................................ 13
Pinout........................................................................................... 22
Auxiliary Switch.......................................................................... 14
Cable Lengths and Equalization............................................... 23
Serial Control Interface.................................................................. 15
PCB Layout Guidelines.............................................................. 23
Reset ............................................................................................. 15
Outline Dimensions ....................................................................... 27
Write Procedure.......................................................................... 15
Ordering Guide .......................................................................... 27
Read Procedure........................................................................... 16
REVISION HISTORY
11/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
AD8191A
SPECIFICATIONS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input
swing = 1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
Maximum Data Rate (DR) per Channel
Bit Error Rate (BER)
Added Deterministic Jitter
Added Random Jitter
Differential Intrapair Skew 1
Differential Interpair Skew1
EQUALIZATION PERFORMANCE
Receiver (Highest Setting) 2
Transmitter (Highest Setting) 3
INPUT CHARACTERISTICS
Input Voltage Swing
Input Common-Mode Voltage (VICM)
OUTPUT CHARACTERISTICS
High Voltage Level
Low Voltage Level
Rise/Fall Time (20% to 80%)
INPUT TERMINATION
Resistance
AUXILIARY CHANNELS
On Resistance, RAUX
On Capacitance, CAUX
Input/Output Voltage Range
POWER SUPPLY
AVCC
QUIESCENT CURRENT
AVCC
VTTI
VTTO
Conditions/Comments
Min
NRZ
PRBS 223 − 1
DR ≤ 1.65 Gbps, PRBS 223 − 1
1.65
Max
Unit
Gbps
10−9
At output
At output
40
2
1
40
ps (p-p)
ps (rms)
ps
ps
Boost frequency = 825 MHz
Boost frequency = 825 MHz
12
6
dB
dB
Differential
150
AVCC − 800
1200
AVCC
mV
mV
Single-ended, high speed channel
Single-ended, high speed channel
AVCC − 10
AVCC − 600
75
AVCC + 10
AVCC − 400
200
mV
mV
ps
135
Single ended
50
Ω
DC bias = 2.5 V, ac voltage = 3.5 V, f = 100 kHz
100
8
AMUXVCC
Ω
pF
V
DVEE
Operating range
3
3.3
3.6
V
Outputs disabled
Outputs enabled, no pre-emphasis
Outputs enabled, maximum pre-emphasis
Input termination on 4
Output termination on, no pre-emphasis
Output termination on, maximum pre-emphasis
30
52
95
5
35
72
3.2
40
60
110
40
40
80
7
0.01
44
66
122
54
46
90
8
0.1
mA
mA
mA
mA
mA
mA
mA
mA
Outputs disabled
Outputs enabled, no pre-emphasis
Outputs enabled, maximum pre-emphasis
115
384
704
271
574
910
361
671
1050
mW
mW
mW
200
1.5
ms
ms
ns
DVCC
AMUXVCC
POWER DISSIPATION
TIMING CHARACTERISTICS
Switching/Update Delay
Typ
High speed switching register: HS_CH
All other configuration registers
50
RESET Pulse Width
Rev. 0 | Page 3 of 28
AD8191A
Parameter
SERIAL CONTROL INTERFACE 5
Input High Voltage, VIH
Input Low Voltage, VIL
Output High Voltage, VOH
Output Low Voltage, VOL
PARALLEL CONTROL INTERFACE
Input High Voltage, VIH
Input Low Voltage, VIL
Conditions/Comments
Min
Typ
Max
2
0.4
V
V
V
V
0.8
V
V
0.8
2.4
2
1
Unit
Differential interpair skew is measured between the TMDS pairs of a single link.
AD8191A output meets the transmitter eye diagram as defined in the DVI Standard Revision 1.0 and the HDMI Standard Revision 1.2a.
3
Cable output meets the receiver eye diagram mask as defined in the DVI Standard Revision 1.0 and the HDMI Standard Revision 1.2a.
4
Typical value assumes only the selected HDMI/DVI link is active with nominal signal swings and that the unselected HDMI/DVI links are deactivated. Minimum and
maximum limits are measured at the respective extremes of input termination resistance and input voltage swing.
5
The AD8191A is an I2C slave and its serial control interface is based on the 3.3 V I2C bus specification.
2
Rev. 0 | Page 4 of 28
AD8191A
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 2.
Parameter
AVCC to AVEE
DVCC to DVEE
DVEE to AVEE
VTTI
VTTO
AMUXVCC
Internal Power Dissipation
High Speed Input Voltage
High Speed Differential Input Voltage
Low Speed Input Voltage
I2C® and Parallel Logic Input Voltage
Storage Temperature Range
Operating Temperature Range
Junction Temperature
Rating
3.7 V
3.7 V
±0.3 V
AVCC + 0.6 V
AVCC + 0.6 V
5.5 V
2.2 W
AVCC − 1.4 V < VIN <
AVCC + 0.6 V
2.0 V
DVEE − 0.3 V < VIN <
AMUXVCC + 0.6 V
DVEE − 0.3 V < VIN <
DVCC + 0.6 V
−65°C to +125°C
−40°C to +85°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
θJA is specified for the worst-case conditions: a device soldered
in a 4-layer JEDEC circuit board for surface-mount packages.
θJC is specified for no airflow.
Table 3. Thermal Resistance
Package Type
100-Lead LQFP
θJA
56
θJC
19
Unit
°C/W
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD8191A is limited by the associated rise in junction
temperature. The maximum safe junction temperature for
plastic encapsulated devices is determined by the glass
transition temperature of the plastic, approximately 150°C.
Temporarily exceeding this limit may cause a shift in
parametric performance due to a change in the stresses exerted
on the die by the package.
Exceeding a junction temperature of 175°C for an extended
period can result in device failure. To ensure proper operation, it is
necessary to observe the maximum power rating as determined by
the coefficients in Table 3.
ESD CAUTION
Rev. 0 | Page 5 of 28
AD8191A
75
AVCC
74
IP_C3
AUX_A1
AUX_A2
AUX_A3
DVEE
AUX_B0
AUX_B1
AUX_B2
AUX_B3
AUX_COM0
AUX_COM1
AUX_COM2
AUX_COM3
AUX_C0
AUX_C1
AUX_C2
AUX_C3
AMUXVCC
AUX_D0
AUX_D1
AUX_D2
AUX_D3
PP_EQ
PP_EN
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
AVCC
1
IN_B0
2
IP_B0
3
73
IN_C3
AVEE
4
72
AVEE
IP_C2
PIN 1 INDICATOR
IN_B1
5
71
IP_B1
6
70
IN_C2
VTTI
7
69
VTTI
IP_C1
IN_B2
8
68
IP_B2
9
67
IN_C1
AVEE
10
66
AVEE
IN_B3
11
IP_B3
12
65
IP_C0
64
AVCC
13
IN_C0
63
IN_A0
AVCC
14
62
IP_D3
IP_A0
15
61
IN_D3
AVEE
16
60
AVEE
IP_D2
AD8191A
TOP VIEW
(Not to Scale)
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DVCC
ON2
OP2
VTTO
ON3
OP3
RESET
PP_PRE0
PP_PRE1
DVCC
PP_OCL
I2C_SCL
I2C_SDA
AVEE
OP1
51
36
25
ON1
IN_D0
AVEE
35
IP_D0
52
VTTO
53
24
34
23
IP_A3
OP0
IN_A3
33
AVCC
ON0
54
32
22
DVCC
IN_D1
AVCC
31
IP_D1
55
PP_CH1
56
21
30
20
IP_A2
PP_CH0
IN_A2
29
VTTI
DVEE
57
28
19
I2C_ADDR2
IN_D2
VTTI
27
58
26
59
18
I2C_ADDR0
17
IP_A1
I2C_ADDR1
IN_A1
07013-003
AUX_A0
98
PP_OTO
100
99
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Type 1
Description
1, 13, 22, 54, 63, 75
2
3
4, 10, 16, 25, 51, 60, 66, 72
5
6
7, 19, 57, 69
8
9
11
12
14
15
17
18
20
AVCC
IN_B0
IP_B0
AVEE
IN_B1
IP_B1
VTTI
IN_B2
IP_B2
IN_B3
IP_B3
IN_A0
IP_A0
IN_A1
IP_A1
IN_A2
Power
HS I
HS I
Power
HS I
HS I
Power
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
Positive Analog Supply. 3.3 V nominal.
High Speed Input Complement.
High Speed Input.
Negative Analog Supply. 0 V nominal.
High Speed Input Complement.
High Speed Input.
Input Termination Supply. Nominally connected to AVCC.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
Rev. 0 | Page 6 of 28
AD8191A
Pin No.
Mnemonic
Type 1
Description
21
23
24
26
27
28
29, 95
30
31
32, 38, 47
33
34
35, 41
36
37
39
40
42
43
44
45
46
48
49
50
52
53
55
56
58
59
61
62
64
65
67
68
70
71
73
74
76
77
78
79
80
81
82
83
84
85
86
IP_A2
IN_A3
IP_A3
I2C_ADDR0
I2C_ADDR1
I2C_ADDR2
DVEE
PP_CH0
PP_CH1
DVCC
ON0
OP0
VTTO
ON1
OP1
ON2
OP2
ON3
OP3
RESET
PP_PRE0
PP_PRE1
PP_OCL
I2C_SCL
I2C_SDA
IN_D0
IP_D0
IN_D1
IP_D1
IN_D2
IP_D2
IN_D3
IP_D3
IN_C0
IP_C0
IN_C1
IP_C1
IN_C2
IP_C2
IN_C3
IP_C3
PP_EN
PP_EQ
AUX_D3
AUX_D2
AUX_D1
AUX_D0
AMUXVCC
AUX_C3
AUX_C2
AUX_C1
AUX_C0
HS I
HS I
HS I
Control
Control
Control
Power
Control
Control
Power
HS O
HS O
Power
HS O
HS O
HS O
HS O
HS O
HS O
Control
Control
Control
Control
Control
Control
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
Control
Control
LS I/O
LS I/O
LS I/O
LS I/O
Power
LS I/O
LS I/O
LS I/O
LS I/O
High Speed Input.
High Speed Input Complement.
High Speed Input.
I2C Address First LSB.
I2C Address Second LSB.
I2C Address Third LSB.
Negative Digital and Auxiliary Multiplexer Power Supply. 0 V nominal.
High Speed Source Selection Parallel Interface LSB.
High Speed Source Selection Parallel Interface MSB.
Positive Digital Power Supply. 3.3 V nominal.
High Speed Output Complement.
High Speed Output.
Output Termination Supply. Nominally connected to AVCC.
High Speed Output Complement.
High Speed Output.
High Speed Output Complement.
High Speed Output.
High Speed Output Complement.
High Speed Output.
Configuration Registers Reset. Normally pulled up to AVCC.
High Speed Pre-Emphasis Selection Parallel Interface LSB.
High Speed Pre-Emphasis Selection Parallel Interface MSB.
High Speed Output Current Level Parallel Interface.
I2C Clock.
I2C Data.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Output Enable Parallel Interface.
High Speed Equalization Selection Parallel Interface.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Positive Auxiliary Multiplexer Supply. 5 V typical.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Rev. 0 | Page 7 of 28
AD8191A
Pin No.
Mnemonic
Type 1
Description
87
88
89
90
91
92
93
94
96
97
98
99
100
AUX_COM3
AUX_COM2
AUX_COM1
AUX_COM0
AUX_B3
AUX_B2
AUX_B1
AUX_B0
AUX_A3
AUX_A2
AUX_A1
AUX_A0
PP_OTO
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
LS I/O
Control
Low Speed Common Input/Output.
Low Speed Common Input/Output.
Low Speed Common Input/Output.
Low Speed Common Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
High Speed Output Termination Selection Parallel Interface.
1
HS = high speed, LS = low speed, I = input, O = output.
Rev. 0 | Page 8 of 28
AD8191A
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input
swing = 1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless
otherwise noted.
HDMI CABLE
AD8191A
DIGITAL
PATTERN
GENERATOR
SERIAL DATA
ANALYZER
EVALUATION
BOARD
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
07013-004
SMA COAX CABLE
0.125UI/DIV AT 1.65Gbps
07013-007
250mV/DIV
0.125UI/DIV AT 1.65Gbps
07013-005
250mV/DIV
Figure 4. Test Circuit Diagram for Rx Eye Diagram
Figure 7. Rx Eye Diagram at TP3, EQ = 6 dB (Cable = 2 meters, 30 AWG)
Figure 6. Rx Eye Diagram at TP2 (Cable = 20 meters, 24 AWG)
0.125UI/DIV AT 1.65Gbps
07013-008
0.125UI/DIV AT 1.65Gbps
07013-006
250mV/DIV
250mV/DIV
Figure 5. Rx Eye Diagram at TP2 (Cable = 2 meters, 30 AWG)
Figure 8. Rx Eye Diagram at TP3, EQ = 12 dB (Cable = 20 meters, 24 AWG)
Rev. 0 | Page 9 of 28
AD8191A
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input
swing = 1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless
otherwise noted.
HDMI CABLE
AD8191A
DIGITAL
PATTERN
GENERATOR
SERIAL DATA
ANALYZER
EVALUATION
BOARD
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
07013-009
SMA COAX CABLE
0.125UI/DIV AT 1.65Gbps
Figure 11. Tx Eye Diagram at TP2, PE = 6 dB
0.125UI/DIV AT 1.65Gbps
07013-013
0.125UI/DIV AT 1.65Gbps
07013-011
250mV/DIV
Figure 12. Tx Eye Diagram at TP3, PE = 2 dB (Cable = 2 meters, 30 AWG)
250mV/DIV
Figure 10. Tx Eye Diagram at TP2, PE = 2 dB
07013-012
250mV/DIV
0.125UI/DIV AT 1.65Gbps
07013-010
250mV/DIV
Figure 9. Test Circuit Diagram for Tx Eye Diagrams
Figure 13. Tx Diagram at TP3, PE = 6 dB (Cable = 10 meters, 28 AWG)
Rev. 0 | Page 10 of 28
AD8191A
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input
swing = 1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless
otherwise noted.
0.6
0.4
720p,
EQ = 12dB
1080p,
EQ = 12dB
0.3
1.65Gbps,
EQ = 12dB
0.2
2m CABLE = 30AWG
5m TO 10m CABLES = 28AWG
15m TO 20m CABLES = 24AWG
0.5
DETERMINISTIC JITTER (UI)
0.5
DETERMINISTIC JITTER (UI)
0.6
2m CABLE = 30AWG
5m TO 10m CABLES = 28AWG
15m TO 30m CABLES = 24AWG
480p,
EQ = 12dB
0.1
0.4
720p, PE OFF
1080p, PE OFF
0.3
1080p, MAX PE
0.2
720p, MAX PE
480p, PE OFF
0.1
5
10
15
20
25
35
30
HDMI CABLE LENGTH (m)
07013-014
0
Figure 14. Jitter vs. Input Cable Length (See Figure 4 for Test Setup)
1200
50
1000
40
800
1.65Gbps
1080p
1080i/720p
480p
480i
20
5
10
15
25
20
Figure 17. Jitter vs. Output Cable Length (See Figure 9 for Test Setup)
60
30
0
HDMI CABLE LENGTH (m)
EYE HEIGHT (mV)
JITTER (ps)
0
07013-017
480p, MAX PE
0
600
400
DJ (p-p)
10
200
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
DATA RATE (Gbps)
0
0
0.6
0.8
1.0
1.2
1.4
1.6
1.8
3.6
Figure 18. Eye Height vs. Data Rate
70
800
60
700
600
EYE HEIGHT (mV)
50
40
30
20
10
3.2
3.3
400
300
100
RJ (rms)
3.1
500
200
DJ (p-p)
3.4
SUPPLY VOLTAGE (V)
3.5
3.6
07013-016
JITTER (ps)
0.4
DATA RATE (Gbps)
Figure 15. Jitter vs. Data Rate
0
3.0
0.2
07013-018
0
07013-015
0
07013-019
RJ (rms)
Figure 16. Jitter vs. Supply Voltage
0
3.0
3.1
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
Figure 19. Eye Height vs. Supply Voltage
Rev. 0 | Page 11 of 28
3.5
AD8191A
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input
swing = 1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless
otherwise noted.
30
50
45
25
40
35
JITTER (ps)
DJ (p-p)
15
10
25
20
DJ (p-p)
15
10
5
RJ (rms)
0
0.2
0.4
0.6
0.8
1.0
5
1.2
1.4
1.6
1.8
2.0
DIFFERENTIAL INPUT SWING (mV)
RJ (rms)
0
2.5
07013-020
0
30
2.7
2.9
3.1
3.3
3.5
07013-023
JITTER (ps)
20
3.7
INPUT COMMON-MODE VOLTAGE (V)
Figure 20. Jitter vs. Differential Input Swing
Figure 23. Jitter vs. Input Common-Mode Voltage
120
50
115
DIFFERENTIAL INPUT
TERMINATION RESISTANCE (Ω)
JITTER (ps)
40
30
20
DJ (p-p)
10
110
105
100
95
90
85
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
80
–40
07013-021
0
–60
Figure 21. Jitter vs. Temperature
RISE TIME
100
80
60
40
20
20
40
60
TEMPERATURE (°C)
80
100
07013-022
RISE/FALL TIME 20% TO 80% (ps)
FALL TIME
120
0
20
40
60
80
100
Figure 24. Differential Input Termination Resistance vs. Temperature
140
–20
0
TEMPERATURE (°C)
160
0
–40
–20
Figure 22. Rise/Fall Time vs. Temperature
Rev. 0 | Page 12 of 28
07013-024
RJ (rms)
AD8191A
THEORY OF OPERATION
INTRODUCTION
The primary function of the AD8191A is to switch one of four
(HDMI or DVI) single-link sources to one output. Each HDMI/
DVI link consists of four differential, high speed channels and
four auxiliary single-ended, low speed control signals. The high
speed channels include a data-word clock and three transition
minimized differential signaling (TMDS) data channels running at
10× the data-word clock frequency for data rates up to 1.65 Gbps.
The four low speed control signals are 5 V tolerant bidirectional
lines that can carry configuration signals, HDCP encryption, and
other information, depending upon the specific application.
All four high speed TMDS channels in a given link are identical;
that is, the pixel clock can be run on any of the four TMDS
channels. Transmit and receive channel compensation is provided
for the high speed channels where the user can (manually)
select among a number of fixed settings.
The AD8191A has two control interfaces. Users have the option
of controlling the part through either the parallel control interface
or the I2C serial control interface. The AD8191A has eight userprogrammable I2C slave addresses to allow multiple AD8191As
to be controlled by a single I2C bus. A RESET pin is provided to
restore the control registers of the AD8191A to default values.
In all cases, serial programming values override any prior parallel
programming values, and any use of the serial control interface
disables the parallel control interface until the AD8191A is reset.
The input equalizer can be manually configured to provide two
different levels of high frequency boost: 6 dB or 12 dB. The user
can individually control the equalization level of the eight high
speed input channels by selectively programming the associated
RX_EQ bits in the receive equalizer register through the serial
control interface. Alternately, the user can globally control the
equalization level of all eight high speed input channels by setting
the PP_EQ pin of the parallel control interface. No specific
cable length is suggested for a particular equalization setting
because cable performance varies widely between manufacturers;
however, in general, the equalization of the AD8191A can be set
to 12 dB without degrading the signal integrity, even for short
input cables. At the 12 dB setting, the AD8191A can equalize
more than 20 meters of 24 AWG cable at 1.65 Gbps.
OUTPUT CHANNELS
Each high speed output differential pair is terminated to the
3.3 V VTTO power supply through a 50 Ω on-chip resistor (see
Figure 26). This termination is user-selectable; it can be turned
on or off by programming the TX_PTO bit of the transmitter
settings register through the serial control interface, or by
setting the PP_OTO pin of the parallel control interface.
VTTO
50Ω
50Ω
OPx
ONx
Each high speed input differential pair terminates to the 3.3 V
VTTI power supply through a pair of single-ended 50 Ω on-chip
resistors, as shown in Figure 25. The input terminations can be
optionally disconnected for approximately 100 ms following a
source switch. The user can program which of the 16 high speed
input channels employs this feature by selectively programming
the associated RX_PT bits in the input termination pulse registers
through the serial control interface. Additionally, all the input
terminations can be disconnected by programming the RX_TO
bit in the receiver settings register. By default, the input termination
is enabled. The input terminations are enabled and cannot be
switched when programming the AD8191A through the parallel
control interface.
IP_xx
IN_xx
50Ω
AVEE
Figure 26. High Speed Output Simplified Schematic
The output termination resistors of the AD8191A back-terminate
the output TMDS transmission lines. These back-terminations
act to absorb reflections from impedance discontinuities on the
output traces, improving the signal integrity of the output traces
and adding flexibility to how the output traces can be routed.
For example, interlayer vias can be used to route the AD8191A
TMDS outputs on multiple layers of the PCB without severely
degrading the quality of the output signal.
07013-025
CABLE
EQ
AVEE
IOUT
The AD8191A output has a disable feature that places the
outputs in a tristate mode. This mode is enabled by programming
the HS_EN bit of the high speed device modes register through
the serial control interface or by setting the PP_EN pin of the
parallel control interface. Larger wire-OR’ed arrays can be
constructed using the AD8191A in this mode.
VTTI
50Ω
DISABLE
07013-026
INPUT CHANNELS
Figure 25. High Speed Input Simplified Schematic
Rev. 0 | Page 13 of 28
AD8191A
The AD8191A requires output termination resistors when the
high speed outputs are enabled. Termination can be internal
and/or external. The internal terminations of the AD8191A are
enabled by programming the TX_PTO bit of the transmitter
settings register or by setting the PP_OTO pin of the parallel
control interface. The internal terminations of the AD8191A
default to the setting indicated by PP_OTO upon reset. External
terminations can be provided either by on-board resistors or by
the input termination resistors of an HDMI/DVI receiver. If
both the internal terminations are enabled and external terminations are present, set the output current level to 20 mA by
programming the TX_OCL bit of the transmitter settings
register through the serial control interface or by setting the
PP_OCL pin of the parallel control interface. The output
current level defaults to the level indicated by PP_OCL upon
reset. If only external terminations are provided (if the internal
terminations are disabled), set the output current level to 10 mA
by programming the TX_OCL bit of the transmitter settings
register or by setting the PP_OCL pin of the parallel control
interface. The high speed outputs must be disabled if there are
no output termination resistors present in the system.
The output pre-emphasis can be manually configured to provide
one of four different levels of high frequency boost. The specific
boost level is selected by programming the TX_PE bits of the
transmitter settings register through the serial control interface,
or by setting the PP_PE bus of the parallel control interface. No
specific cable length is suggested for a particular pre-emphasis
setting because cable performance varies widely between
manufacturers.
When turning off the AD8191A, care needs to be taken with the
AMUXVCC supply to ensure that the auxiliary multiplexer pins
remain in a high impedance state. A scenario that illustrates this
requirement is one where the auxiliary multiplexer is used to
switch the display data channel (DDC) bus. In some applications,
additional devices can be connected to the DDC bus (such as an
EEPROM with EDID information) upstream of the AD8191A.
Extended display identification data (EDID) is a VESA standarddefined data format for conveying display configuration
information to sources to optimize display use. EDID devices
may need to be available via the DDC bus, regardless of the
state of the AD8191A and any downstream circuit. For this
configuration, the auxiliary inputs of the powered down
AD8191A need to be in a high impedance state to avoid
pulling down on the DDC lines and preventing these other
devices from using the bus.
The AD8191A requires 5 V on its supply pin, AMUXVCC, in
order for the AUXMUX channels to be high impedance. When
a TV is turned off, it cannot provide such a supply; however, it
can be provided from any HDMI source that is plugged into it.
A Schottky diode network, as shown in Figure 28, uses the 5 V
supply (Pin 18) from any HDMI/DVI source to power AMUXVCC
and guarantee high impedance of the auxiliary multiplexer pins.
The AMUXVCC supply does not draw any significant static
current. The use of diodes ensures that connected HDMI sources
do not load this circuit if their 5 V pin is low impedance when
turned off. The 100 kΩ resistor ensures that a minimum of
current flows through the diodes to keep them forward biased.
AUXILIARY SWITCH
This precaution does not need to be taken if the DDC peripheral
circuitry is connected to the bus downstream of the AD8191A.
The auxiliary (low speed) lines have no amplification. They are
routed using a passive switch that is bandwidth compatible with
the standard speed I2C. The schematic equivalent for this
passive connection is shown in Figure 27.
+5V INTERNAL
(IF ANY)
PIN 18 HDMI CONNECTOR
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
PIN 14 DVI CONNECTOR
BAT54L BAT54L
BAT54L
SOURCE A +5V
+5V SOURCE C
I<50mA
AUX_COM0
½CAUX
I<50mA
AMUXVCC
PERIPHERAL
CIRCUITRY
Figure 27. Auxiliary Channel Simplified Schematic,
AUX_A0 to AUX_COM0 Routing Example
AD8191A
PERIPHERAL
CIRCUITRY
I<50mA
PERIPHERAL
CIRCUITRY
PERIPHERAL
CIRCUITRY
100kΩ
I<50mA
SOURCE B +5V
+5V SOURCE D
BAT54L
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
BAT54L
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
Figure 28. Suggested AMUXVCC Power Scheme
Rev. 0 | Page 14 of 28
07013-028
½CAUX
RAUX
07013-027
AUX_A0
AD8191A
SERIAL CONTROL INTERFACE
RESET
4.
Wait for the AD8191A to acknowledge the request.
On initial power-up, or at any point in operation, the AD8191A
register set can be restored to preprogrammed default values by
pulling the RESET pin low in accordance with the specifications
in Table 1. During normal operation, however, the RESET pin
must be pulled up to 3.3 V. Following a reset, the preprogrammed
default values of the AD8191A register set correspond to the
state of the parallel interface configuration registers, as listed in
Table 18. The AD8191A can be controlled through the parallel
control interface until the first serial control event occurs.
As soon as any serial control event occurs, the serial
programming values, corresponding to the state of the serial
interface configuration registers (see Table 5), override any
prior parallel programming values, and the parallel control
interface is disabled until the part is subsequently reset.
5.
Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
6.
Wait for the AD8191A to acknowledge the request.
7.
Send the data (eight bits) to be written to the register
whose address was set in Step 5. This transfer should be
MSB first.
8.
Wait for the AD8191A to acknowledge the request.
9.
Perform one of the following:
9a. Send a stop condition (while holding the I2C_SCL
line high, pull the I2C_SDA line high) and release
control of the bus to end the transaction (shown in
Figure 29).
WRITE PROCEDURE
To write data to the AD8191A register set, an I2C master (such
as a microcontroller) needs to send the appropriate control
signals to the AD8191A slave device. The signals are controlled
by the I2C master, unless otherwise specified. For a diagram of
the procedure, see Figure 29. The steps for a write procedure are
as follows:
1.
Send a start condition (while holding the I2C_SCL line
high, pull the I2C_SDA line low).
2.
Send the AD8191A part address (seven bits). The upper
four bits of the AD8191A part address are the static value
[1001] and the three LSBs are set by Input Pin I2C_ADDR2,
Input Pin I2C_ADDR1, and Input Pin I2C_ADDR0 (LSB).
This transfer should be MSB first.
9c. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of the read procedure (in the
Read Procedure section) to perform a read from
another address.
9d. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 8 of the read procedure (in the
Read Procedure section) to perform a read from the
same address set in Step 5.
Send the write indicator bit (0).
*
I2C_SCL
R/W
GENERAL CASE
I2C_SDA
START
FIXED PART
ADDR
ADDR
REGISTER ADDR
ACK
DATA
ACK
STOP
ACK
EXAMPLE
I2C_SDA
1
2
3
4
5
*THE SWITCHING/UPDATE DELAY BEGINS AT THE FALLING EDGE OF THE
LAST DATA BIT; FOR EXAMPLE, THE FALLING EDGE JUST BEFORE STEP 8.
Figure 29. I2C Write Diagram
Rev. 0 | Page 15 of 28
6
7
8
9
07013-029
3.
9b. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 in this procedure to perform
another write.
AD8191A
13. Perform one of the following:
READ PROCEDURE
To read data from the AD8191A register set, an I2C master
(such as a microcontroller) needs to send the appropriate
control signals to the AD8191A slave device. The signals are
controlled by the I2C master, unless otherwise specified. For a
diagram of the procedure, see Figure 30. The steps for a read
procedure are as follows:
1.
Send a start condition (while holding the I2C_SCL line
high, pull the I2C_SDA line low).
2.
Send the AD8191A part address (seven bits). The upper
four bits of the AD8191A part address are the static value
[1001] and the three LSBs are set by Input Pin I2C_ADDR2,
Input Pin I2C_ADDR1, and Input Pin I2C_ADDR0 (LSB).
This transfer should be MSB first.
3.
Send the write indicator bit (0).
4.
Wait for the AD8191A to acknowledge the request.
5.
Send the register address (eight bits) from which data is to
be read. This transfer should be MSB first.
6.
Wait for the AD8191A to acknowledge the request.
7.
Send a repeated start condition (Sr) by holding the
I2C_SCL line high and pulling the I2C_SDA line low.
8.
Resend the AD8191A part address (seven bits) from
Step 2. The upper four bits of the AD8191A part address
are the static value [1001] and the three LSBs are set by the
Input Pin I2C_ADDR2, I2C_ADDR1 and Input
Pin I2C_ADDR0 (LSB). This transfer should be MSB first.
9.
Send the read indicator bit (1).
13a. Send a stop condition (while holding the I2C_SCL
line high, pull the SDA line high) and release control
of the bus to end the transaction (shown in Figure 30).
13b. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of the write procedure (previous
Write Procedure section) to perform a write.
13c. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of this procedure to perform a
read from another address.
13d. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 8 of this procedure to perform a
read from the same address.
SWITCHING/UPDATE DELAY
There is a delay between when a user writes to the configuration registers of the AD8191A and when that state change takes
physical effect. This update delay occurs regardless of whether
the user programs the AD8191A via the serial or the parallel
control interface. When using the serial control interface, the
update delay begins at the falling edge of I2C_SCL for the last
data bit transferred, as shown in Figure 29. When using the
parallel control interface, the update delay begins at the transition
edge of the relevant parallel interface pin. This update delay is
register specific and the times are specified in Table 1.
During a delay window, new values can be written to the
configuration registers, but the AD8191A does not physically
update until the end of that register’s delay window. Writing
new values during the delay window does not reset the window;
new values supersede the previously written values. At the end
of the delay window, the AD8191A physically assumes the state
indicated by the last set of values written to the configuration
registers. If the configuration registers are written after the delay
window ends, the AD8191A immediately updates and a new
delay window begins.
10. Wait for the AD8191A to acknowledge the request.
11. The AD8191A serially transfers the data (eight bits) held in
the register indicated by the address set in Step 5. This data
is sent MSB first.
12. Acknowledge the data from the AD8191A.
I2C_SCL
R/W
GENERAL CASE
I2C_SDA
START
FIXED PART
ADDR
R/W
ADDR
SR
REGISTER ADDR
ACK
FIXED PART
ADDR
ACK
ADDR
DATA
STOP
ACK
ACK
9 10 11
12
1
2
3
4
5
6
7
2
8
Figure 30. I C Read Diagram
Rev. 0 | Page 16 of 28
13
07013-030
EXAMPLE
I2C_SDA
AD8191A
PARALLEL CONTROL INTERFACE
The AD8191A can be controlled through the parallel interface
using the PP_EN, PP_CH[1:0], PP_EQ, PP_PRE[1:0], PP_OTO,
and PP_OCL pins. Logic levels for the parallel interface pins are
set in accordance with the specifications listed in Table 1.
Setting these pins updates the parallel control interface registers,
as listed in Table 18. Following a reset, the AD8191A can be
controlled through the parallel control interface until the first
serial control event occurs. As soon as any serial control event
occurs, the serial programming values override any prior
parallel programming values, and the parallel control interface
is disabled until the part is subsequently reset. The default serial
programming values correspond to the state of the serial
interface configuration registers, as listed in Table 5.
Note that after changing the status of the channel selection
(PP_CH[1:0]), it is necessary to assert a low logic level to RESET
RESET to ensure that the channel select status is properly updated.
Rev. 0 | Page 17 of 28
AD8191A
SERIAL INTERFACE CONFIGURATION REGISTERS
The serial interface configuration registers can be read and written using the I2C serial control interface, Pin I2C_SDA, and Pin I2C_SCL.
The least significant bits of the AD8191A I2C part address are set by tying Pin I2C_ADDR2, Pin I2C_ADDR1, and Pin I2C_ADDR0 to
3.3 V (Logic 1) or 0 V (Logic 0). As soon as the serial control interface is used, the parallel control interface is disabled until the AD8191A
is reset, as described in the Serial Control Interface section.
Table 5. Serial (I2C) Interface Register Map
Name
Bit 7
High Speed
Device
Modes
Bit 6
High
speed
switch
enable
HS_EN
Auxiliary
switch
enable
AUX_EN
Auxiliary
Device
Modes
Bit 5
0
0
Bit 4
Bit 3
0
Bit 2
0
0
Bit 1
0
0
0
Addr
Default
High speed source select
0x00
0x40
HS_CH[1]
HS_CH[0]
Auxiliary switch source select
0x01
0x40
0x10
0x01
0x11
0x00
0x12
0x00
0x13
0x00
0x14
0x00
0x20
0x03
AUX_CH[1]
Receiver
Settings
Input
Termination
Pulse
Register 1
Input
Termination
Pulse
Register 2
Receive
Equalizer
Register 1
Receive
Equalizer
Register 2
Transmitter
Settings
Bit 0
AUX_CH[0]
High speed
input
termination
select
RX_TO
RX_PT[7]
Source A and Source B: input termination pulse-on-source switch select
(disconnect termination for a short period of time)
RX_PT[6]
RX_PT[5]
RX_PT[4]
RX_PT[3]
RX_PT[2]
RX_PT[1]
RX_PT[15]
Source C and Source D: input termination pulse-on-source switch select
(disconnect termination for a short period of time)
RX_PO[14] RX_PT[13]
RX_PT[12]
RX_PT[11]
RX_PT[10]
RX_PT[9]
RX_PT[8]
RX_EQ[7]
RX_EQ[6]
Source A and Source B: input equalization level select
RX_EQ[5]
RX_EQ[4]
RX_EQ[3]
RX_EQ[2]
RX_EQ[1]
RX_EQ[0]
RX_EQ[15]
RX_EQ[14]
Source C and Source D: input equalization level select
RX_EQ[13]
RX_EQ[12]
RX_EQ[11]
RX_EQ[10]
RX_EQ[9]
RX_EQ[8]
High speed output
pre-emphasis level select
TX_PE[1]
TX_PE[0]
High speed
output
termination
select
TX_PTO
RX_PT[0]
High speed
output current
level select
TX_OCL
HIGH SPEED DEVICE MODES REGISTER
AUXILIARY DEVICE MODES REGISTER
HS_EN: High Speed (TMDS) Channels Enable Bit
AUX_EN: Auxiliary (Low Speed) Switch Enable Bit
Table 6. HS_EN Description
Table 8. AUX_EN Description
HS_EN
0
1
AUX_EN
0
Description
High speed channels off, low power/standby mode
High speed channels on
1
HS_CH[1:0]: High Speed (TMDS) Switch Source Select Bus
Table 7. HS_CH Mapping
HS_CH[1:0]
00
01
10
11
O[3:0]
A[3:0]
B[3:0]
C[3:0]
D[3:0]
Description
High Speed Source A switched to output
High Speed Source B switched to output
High Speed Source C switched to output
High Speed Source D switched to output
Rev. 0 | Page 18 of 28
Description
Auxiliary switch off, no low speed input/output to
low speed common input/output connection
Auxiliary switch on
AD8191A
AUX_CH[1:0]: Auxiliary (Low Speed) Switch Source
Select Bus
RECEIVE EQUALIZER REGISTER 1 AND REGISTER 2
RX_EQ[x]: High Speed (TMDS) Input X Equalization Level
Select Bit
Table 9. AUX_CH Mapping
AUX_CH[1:0]
00
AUX_COM[3:0]
AUX_A[3:0]
01
AUX_B[3:0]
10
AUX_C[3:0]
11
AUX_D[3:0]
Description
Auxiliary Source A switched
to output
Auxiliary Source B switched
to output
Auxiliary Source C switched
to output
Auxiliary Source D switched
to output
RECEIVER SETTINGS REGISTER
RX_TO: High Speed (TMDS) Channels Input Termination
On/Off Select Bit
Table 10. RX_TO Description
RX_TO
0
1
Description
Input termination off
Input termination on (can be pulsed on and off
according to settings in the input termination
pulse register)
INPUT TERMINATION PULSE REGISTER 1 AND
REGISTER 2
RX_PT[x]: High Speed (TMDS) Input Channel X
Pulse-On-Source Switch Select Bit
Table 11. RX_PT[x] Description
RX_PT[x]
0
1
Description
Input termination for TMDS Channel X always
connected when source is switched
Input termination for TMDS Channel X disconnected
for 100 ms when source is switched
Table 12. RX_PT[x] Mapping
RX_PT[x]
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
Corresponding Input TMDS Channel
B0
B1
B2
B3
A0
A1
A2
A3
C3
C2
C1
C0
D3
D2
D1
D0
Table 13. RX_EQ[x] Description
RX_EQ[x]
0
1
Description
Low equalization (6 dB)
High equalization (12 dB)
Table 14. RX_EQ[x] Mapping
RX_EQ[x]
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
Corresponding Input TMDS Channel
B0
B1
B2
B3
A0
A1
A2
A3
C3
C2
C1
C0
D3
D2
D1
D0
TRANSMITTER SETTINGS REGISTER
TX_PE[1:0]: High Speed (TMDS) Output Pre-Emphasis
Level Select Bus (For All TMDS Channels)
Table 15. TX_PE[1:0] Description
TX_PE[1:0]
00
01
10
11
Description
No pre-emphasis (0 dB)
Low pre-emphasis (2 dB)
Medium pre-emphasis (4 dB)
High pre-emphasis (6 dB)
TX_PTO: High Speed (TMDS) Output Termination On/Off
Select Bit (For All Channels)
Table 16. TX_PTO Description
TX_PTO
0
1
Description
Output termination off
Output termination on
TX_OCL: High Speed (TMDS) Output Current Level Select
Bit (For All Channels)
Table 17. TX_OCL Description
TX_OCL
0
1
Rev. 0 | Page 19 of 28
Description
Output current set to 10 mA
Output current set to 20 mA
AD8191A
PARALLEL INTERFACE CONFIGURATION REGISTERS
The parallel interface configuration registers can be directly set using the PP_EN, PP_CH[1:0], PP_EQ, PP_PRE[1:0], PP_OTO, and
PP_OCL pins. This interface is only accessible after the part is reset and before any registers are accessed using the serial control interface.
The state of each pin is set by tying it to 3.3 V (Logic 1) or 0 V (Logic 0).
Table 18. Parallel Interface Register Map
Name
High Speed
Device Modes
Bit 7
Bit 6
High speed
channel
enable
PP_EN
Auxiliary
switch enable
1
Auxiliary
Device Modes
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
High speed source select
0
0
0
0
PP_CH[1]
PP_CH[0]
Auxiliary switch source select
0
0
0
0
PP_CH[1]
PP_CH[0]
Input termination
on/off select
(termination always on)
1
Receiver
Settings
Input
Termination
Pulse Register 1
Input
Termination
Pulse Register 2
Receive
Equalizer
Register 1
Receive
Equalizer
Register 2
Transmitter
Settings
0
0
Source A and Source B input termination select (termination always off )
0
0
0
0
0
0
0
0
Source C and Source D input termination select (termination always off )
0
0
0
0
0
0
PP_EQ
PP_EQ
PP_EQ
Source A and Source B input equalization level select
PP_EQ
PP_EQ
PP_EQ
PP_EQ
PP_EQ
PP_EQ
PP_EQ
PP_EQ
Source C and Source D input equalization level select
PP_EQ
PP_EQ
PP_EQ
PP_EQ
PP_EQ
Output pre-emphasis
level select
PP_PE[1]
PP_PE[0]
Output
termination
on/off select
PP_OTO
Output current level
select
PP_OCL
HIGH SPEED DEVICE MODES REGISTER
AUXILIARY DEVICE MODES REGISTER
PP_EN: High Speed (TMDS) Channels Enable Bit
PP_CH[1:0]: Auxiliary Switch Source Select Bus
Table 19. PP_EN Description
Table 21. Auxiliary Switch Mapping
PP_EN
0
1
PP_CH[1:0]
00
AUX_COM[3:0]
AUX_A[3:0]
01
AUX_B[3:0]0
10
AUX_C[3:0]
11
AUX_D[3:0]
Description
High speed channels off, low power/standby mode
High speed channels on
PP_CH[1:0]: High Speed (TMDS) Switch Source Select Bus
Table 20. High Speed Switch Mapping
PP_CH[1:0]
00
01
10
11
O[3:0]
A[3:0]
B[3:0]
C[3:0]
D[3:0]
Description
High Speed Source A switched to output
High Speed Source B switched to output
High Speed Source C switched to output
High Speed Source D switched to output
Description
Auxiliary Source A switched to
output
Auxiliary Source B switched to
output
Auxiliary Source C switched to
output
Auxiliary Source D switched to
output
RECEIVER SETTINGS REGISTER
High speed (TMDS) channels input termination is fixed to on
when using the parallel interface.
Rev. 0 | Page 20 of 28
AD8191A
INPUT TERMINATION PULSE REGISTER 1 AND
REGISTER 2
PP_OTO: High Speed (TMDS) Output Termination On/Off
Select Bit (For All TMDS Channels)
High speed input (TMDS) channels pulse-on-source switching
fixed to off when using the parallel interface.
Table 24. PP_OTO Description
RECEIVE EQUALIZER REGISTER 1 AND REGISTER 2
PP_EQ: High Speed (TMDS) Input Equalization Level
Select Bit (For All TMDS Input Channels)
The input equalization cannot be set individually (per channel)
when using the parallel interface; one equalization setting
affects all input channels.
Table 22. PP_EQ Description
PP_EQ
0
1
Description
Low equalization (6 dB)
High equalization (12 dB)
PP_OTO
0
1
PP_OCL: High Speed (TMDS) Output Current Level Select
Bit (For All TMDS Channels)
Table 25. TX_OCL Description
PP_OCL
0
1
TRANSMITTER SETTINGS REGISTER
PP_PE[1:0]: High Speed (TMDS) Output Pre-Emphasis
Level Select Bus (For All TMDS Channels)
Table 23. PP_PE[1:0] Description
PP_PE[1:0]
00
01
10
11
Description
Output termination off
Output termination on
Description
No pre-emphasis (0 dB)
Low pre-emphasis (2 dB)
Medium pre-emphasis (4 dB)
High pre-emphasis (6 dB)
Rev. 0 | Page 21 of 28
Description
Output current set to 10 mA
Output current set to 20 mA
AD8191A
07013-031
APPLICATIONS INFORMATION
Figure 31. Layout of the TMDS Traces on the AD8191A Evaluation Board (Only Top Signal Routing Layer is Shown)
The AD8191A is an HDMI/DVI switch featuring equalized
TMDS inputs and pre-emphasized TMDS outputs. It is intended
for use as a 4:1 switch in systems with long cable runs on both
the input and/or the output and is fully HDMI 1.2a receivecompliant.
PINOUT
The AD8191A is designed to have an HDMI/DVI receiver
pinout at its input and a transmitter pinout at its output, which
makes the AD8191A ideal for use in AVR-type applications
where a designer routes both the inputs and the outputs directly
to HDMI/DVI connectors. This type of layout is used on the
AD8191A evaluation board, as shown in Figure 31. When the
AD8191A is used in receiver type applications, it is necessary to
change the order of the output pins on the PCB to align with the
on-board receiver.
One advantage of the AD8191A in an AVR-type application is
that all of the high speed signals can be routed on one side (the
topside) of the board, as shown in Figure 31. In addition to 12 dB of
input equalization, the AD8191A provides up to 6 dB of output
pre-emphasis that boosts the output TMDS signals and allows
the AD8191A to precompensate when driving long
PCB traces or output cables. The net effect of the input
equalization and output pre-emphasis of the AD8191A is that
the AD8191A can compensate for the signal degradation of
both input and output cables; it acts to reopen a closed input
data eye and transmits a full-swing HDMI signal to an end
receiver.
The AD8191A also provides a distinct advantage in receive-type
applications because it is a fully buffered HDMI/DVI switch.
Although inverting the output pin order of the AD8191A on the
PCB requires a designer to place vias in the high speed signal
path, the AD8191A fully buffers and electrically decouples the
outputs from the inputs. Consequently, the effects of the vias
placed on the output signal lines are not seen at the input of the
AD8191A. The programmable output terminations also improve
signal quality at the output of the AD8191A. Therefore, the PCB
designer has significantly improved flexibility in the placement
and routing of the output signal path with the AD8191A over
other solutions.
Rev. 0 | Page 22 of 28
AD8191A
CABLE LENGTHS AND EQUALIZATION
The AD8191A offers two levels of programmable equalization
for the high speed inputs: 6 dB and 12 dB. The equalizer of the
AD8191A supports video data rates of 1.65 Gbps. It can
equalize up to 20 meters of 24 AWG HDMI cable at data rates
corresponding to the video format, 1080p.
The length of cable that can be used in a typical HDMI/DVI
application depends on a large number of factors, including:
•
Cable quality: the quality of the cable in terms of conductor
wire gauge and shielding. Thicker conductors have lower
signal degradation per unit length.
•
Data rate: the data rate being sent over the cable. The signal
degradation of HDMI cables increases with data rate.
•
Edge rates: the edge rates of the source input. Slower input
edges result in more significant data eye closure at the end
of a cable.
•
Receiver sensitivity: the sensitivity of the terminating
receiver.
As such, specific cable types and lengths are not recommended
for use with a particular equalizer setting. In nearly all applications, the AD8191A equalization level can be set to high, or 12 dB,
for all input cable configurations at all data rates, without degrading
the signal integrity.
PCB LAYOUT GUIDELINES
The AD8191A is used to switch two distinctly different types
of signals, both of which are required for HDMI and DVI video.
These signal groups require different treatment when laying
out a PCB.
The first group of signals carries the audiovisual (AV) data. HDMI/
DVI video signals are differential, unidirectional, and high speed
(up to 1.65 Gbps). The channels that carry the video data must
be controlled impedance, terminated at the receiver, and capable
of operating up to at least 1.65 Gbps. It is especially important
to note that the differential traces that carry the TMDS signals
should be designed with a controlled differential impedance of
100 Ω. The AD8191A provides single-ended, 50 Ω terminations
on-chip for both its inputs and outputs, and both the input and
output terminations can be enabled or disabled through the
serial interface. Transmitter termination is not fully specified by
the HDMI standard but its inclusion improves the overall system
signal integrity.
The audiovisual data carried on these high speed channels are
encoded by a technique called transmission minimized differential
signaling (TMDS) and, in the case of HDMI, is also encrypted
according to the high bandwidth digital copy protection (HDCP)
standard.
The second group of signals consists of low speed auxiliary
control signals used for communication between a source and a
sink. Depending upon the application, these signals can include
the DDC bus (an I2C bus used to send EDID information and
HDCP encryption keys between the source and the sink), the
consumer electronics control (CEC) line, and the hot plug
detect (HPD) line. These auxiliary signals are bidirectional, low
speed, and transferred over a single-ended transmission line
that does not need to have controlled impedance. The primary
concern with laying out the auxiliary lines is ensuring that they
conform to the I2C bus standard and do not have excessive
capacitive loading.
TMDS Signals
In the HDMI/DVI standard, four differential pairs carry the
TMDS signals. In DVI, three of these pairs are dedicated to
carrying RGB video and sync data. For HDMI, audio data is
interleaved with the video data; the DVI standard does not
incorporate audio information. The fourth high speed differential
pair is used for the AV data-word clock and runs at one-tenth
the speed of the TMDS data channels.
The four high speed channels of the AD8191A are identical.
No concession was made to lower the bandwidth of the fourth
channel for the pixel clock; therefore, any channel can be used
for any TMDS signal. The user chooses which signal is routed
over which channel. Additionally, the TMDS channels are
symmetrical; therefore, the p and n of a given differential pair
are interchangeable, provided the inversion is consistent across
all inputs and outputs of the AD8191A. However, the routing
between inputs and outputs through the AD8191A is fixed.
The AD8191A buffers the TMDS signals and the input traces
can be considered electrically independent of the output traces.
In most applications, the quality of the signal on the input TMDS
traces is more sensitive to the PCB layout. Regardless of the data
being carried on a specific TMDS channel, or whether the TMDS
line is at the input or the output of the AD8191A, all four high
speed signals should be routed on a PCB in accordance with the
same RF layout guidelines.
Layout for the TMDS Signals
The TMDS differential pairs can be either microstrip traces,
routed on the outer layer of a board, or stripline traces, routed
on an internal layer of the board. If microstrip traces are used,
there should be a continuous reference plane on the PCB layer
directly below the traces. If stripline traces are used, they must
be sandwiched between two continuous reference planes in the
PCB stack-up.
Rev. 0 | Page 23 of 28
AD8191A
Additionally, the p and n of each differential pair must have a
controlled differential impedance of 100 Ω. The characteristic
impedance of a differential pair is a function of several variables
including the trace width, the distance separating the two traces,
the spacing between the traces and the reference plane, and the
dielectric constant of the PCB binder material. Interlayer vias
introduce impedance discontinuities that can cause reflections
and jitter on the signal path; therefore, it is preferable to route
the TMDS lines exclusively on one layer of the board,
particularly for the input traces. In some applications, such as
using multiple AD8191As to construct large input arrays, the
use of interlayer vias becomes unavoidable. In these situations,
the input termination feature of the AD8191A improves system
signal integrity by absorbing reflections. Take care to use vias
minimally and to place vias symmetrically for each side of a
given differential pair. Furthermore, to prevent unwanted signal
coupling and interference, route the TMDS signals away from
other signals and noise sources on the PCB.
Both traces of a given differential pair must be equal in length
to minimize intrapair skew. Maintaining the physical symmetry
of a differential pair is integral to ensuring its signal integrity;
excessive intrapair skew can introduce jitter through duty cycle
distortion (DCD). The p and n of a given differential pair
should always be routed together to establish the required 100 Ω
differential impedance. Enough space should be left between the
differential pairs of a given group so that the n of one pair does
not couple to the p of another pair. For example, one technique is
to make the interpair distance 4 to 10 times wider than the
intrapair spacing.
Any group of four TMDS channels (that is, Input A, Input B,
Input C, Input D, or the output quad group) should have closely
matched trace lengths to minimize interpair skew. Severe
interpair skew can cause the data on the four different channels
of a group to arrive out of alignment with one another. A good
practice is to match the trace lengths for a given group of four
channels to within 0.05 inches on FR4 material.
The length of the TMDS traces should be minimized to reduce
overall signal degradation. Commonly used PCB material, such
as FR4, is lossy at high frequencies; therefore, long traces on the
circuit board increase signal attenuation resulting in decreased
signal swing and increased jitter through intersymbol
interference (ISI).
Controlling the Characteristic Impedance of a TMDS
Differential Pair
The characteristic impedance of a differential pair depends on a
number of variables including the trace width, the distance
between the two traces, the height of the dielectric material
between the trace and the reference plane below it, and the
dielectric constant of the PCB binder material. To a lesser
extent, the characteristic impedance also depends upon the
trace thickness and the presence of solder mask. There are
many combinations that can produce the correct characteristic
impedance. Generally, working with the PCB fabricator is required
to obtain a set of parameters to produce the desired results.
One consideration is how to guarantee a differential pair with a
differential impedance of 100 Ω over the entire length of the
trace. One technique to accomplish this is to change the width
of the traces in a differential pair based on how closely one trace
is coupled to the other. When the two traces of a differential
pair are close and strongly coupled, they should have a width
that produces a 100 Ω differential impedance. When the traces
split apart, to go into a connector, for example, and are no
longer so strongly coupled, the width of the traces should be
increased to yield a differential impedance of 100 Ω in the new
configuration.
TMDS Terminations
The AD8191A provides internal, 50 Ω single-ended
terminations for all of its high speed inputs and outputs. It is
not necessary to include external termination resistors for the
TMDS differential pairs on the PCB.
The output termination resistors of the AD8191A backterminate the output TMDS transmission lines. These backterminations act to absorb reflections from impedance
discontinuities on the output traces, improving the signal
integrity of the output traces and adding flexibility to how the
output traces can be routed. For example, interlayer vias can be
used to route the AD8191A TMDS outputs on multiple layers of
the PCB without severely degrading the quality of the output signal.
Rev. 0 | Page 24 of 28
AD8191A
This 50 pF limit includes the HDMI connector, the PCB, and
whatever capacitance is seen at the input of the AD8191A, or an
equivalent receiver. There is a similar limit of 100 pF of input
capacitance for the CEC line.
Ground Current Return
In some applications, it can be necessary to invert the output
pin order of the AD8191A, which requires a designer to route
the TMDS traces on multiple layers of the PCB. When routing
differential pairs on multiple layers, it is also necessary to
reroute the corresponding reference plane to provide one
continuous ground current return path for the differential
signals. Standard plated through-hole vias are acceptable for
both the TMDS traces and the reference plane. An example of
this is illustrated in Figure 32.
The parasitic capacitance of traces on a PCB increases with
trace length. To help ensure that a design satisfies the HDMI
specification, the length of the CEC and DDC lines on the PCB
should be made as short as possible. Additionally, if there is a
reference plane in the layer adjacent to the auxiliary traces in
the PCB stackup, relieving or clearing out this reference plane
directly under the auxiliary traces significantly decreases the
amount of parasitic trace capacitance. An example of the board
stackup is shown in Figure 33.
THROUGH-HOLE VIAS
SILKSCREEN
3W
LAYER 1: SIGNAL (MICROSTRIP)
W
3W
PCB DIELECTRIC
SILKSCREEN
LAYER 2: GND (REFERENCE PLANE)
LAYER 1: SIGNAL (MICROSTRIP)
PCB DIELECTRIC
PCB DIELECTRIC
LAYER 3: PWR
(REFERENCE PLANE)
LAYER 2: GND (REFERENCE PLANE)
PCB DIELECTRIC
PCB DIELECTRIC
LAYER 4: SIGNAL (MICROSTRIP)
LAYER 3: PWR (REFERENCE PLANE)
PCB DIELECTRIC
SILKSCREEN
LAYER 4: SIGNAL (MICROSTRIP)
REFERENCE LAYER
RELIEVED UNDERNEATH
MICROSTRIP
Figure 32. Example Routing of Reference Plane
07013-032
SILKSCREEN
07013-035
KEEP REFERENCE PLANE
ADJACENT TO SIGNAL ON ALL
LAYERS TO PROVIDE CONTINUOUS
GROUND CURRENT RETURN PATH.
Figure 33. Example Board Stackup
Auxiliary Control Signals
There are four single-ended control signals associated with each
source or sink in an HDMI/DVI application: hot plug detect
(HPD), consumer electronics control (CEC), and two display
data channel (DDC) lines. The two signals on the DDC bus are
SDA and SCL (serial data and serial clock, respectively). These
four signals can be switched through the auxiliary bus of the
AD8191A and do not need to be routed with the same strict
considerations as the high speed TMDS signals.
In general, it is sufficient to route each auxiliary signal as a
single-ended trace. These signals are not sensitive to impedance
discontinuities, do not require a reference plane, and can be
routed on multiple layers of the PCB. However, it is best to
follow strict layout practices whenever possible to prevent the
PCB design from affecting the overall application. The specific
routing of the HPD, CEC, and DDC lines depends upon the
application in which the AD8191A is being used.
For example, the maximum speed of signals present on the
auxiliary lines is 100 kHz I2C data on the DDC lines; therefore,
any layout that enables 100 kHz I2C to be passed over the DDC
bus should suffice. The HDMI 1.2a specification, however,
places a strict 50 pF limit on the amount of capacitance that can
be measured on either SDA or SCL at the HDMI input connector.
HPD is a dc signal presented by a sink to a source to indicate
that the source EDID is available for reading. The placement of
this signal is not critical, but it should be routed as directly as
possible.
When the AD8191A is powered up, one set of the auxiliary
inputs is passively routed to the outputs. In this state, the
AD8191A looks like a 100 Ω resistor between the selected
auxiliary inputs and the corresponding outputs, as illustrated in
Figure 27. The AD8191A does not buffer the auxiliary signals;
therefore, the input traces, output traces, and the connection
through the AD8191A all must be considered when designing a
PCB to meet HDMI/DVI specifications. The unselected auxiliary
inputs of the AD8191A are placed into a high impedance mode
when the device is powered up. To ensure that all of the
auxiliary inputs of the AD8191A are in a high impedance mode
when the device is powered off, it is necessary to power the
AMUXVCC supply as illustrated in Figure 28.
In contrast to the auxiliary signals, the AD8191A buffers the
TMDS signals, allowing a PCB designer to layout the TMDS
inputs independently of the outputs.
Rev. 0 | Page 25 of 28
AD8191A
RECOMMENDED
Power Supplies
The AD8191A has five separate power supplies referenced to
two separate grounds. The supply/ground pairs are:
AVCC/AVEE
•
VTTI/AVEE
•
VTTO/AVEE
•
DVCC/DVEE
•
AMUXVCC/DVEE
EXTRA ADDED INDUCTANCE
07013-033
•
NOT RECOMMENDED
Figure 34. Recommended Pad Outline for Bypass Capacitors
The AVCC/AVEE (3.3 V) and DVCC/DVEE (3.3 V) supplies
power the core of the AD8191A. The VTTI/AVEE supply
(3.3 V) powers the input termination (see Figure 25). Similarly,
the VTTO/AVEE supply (3.3 V) powers the output termination
(see Figure 26). The AMUXVCC/DVEE supply (3.3 V to 5 V)
powers the auxiliary multiplexer core and determines the
maximum allowed voltage on the auxiliary lines. For example,
if the DDC bus is using 5 V I2C, AMUXVCC should be connected
to 5 V relative to DVEE.
In applications where the AD8191A is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF capacitor, one 1000 pF capacitor, two
0.01 μF capacitors, and one 4.7 μF capacitor. The capacitors
should via down directly to the supply planes and be placed
within a few centimeters of the AD8191A. The AMUXVCC
supply does not require additional bypassing. This bypassing
scheme is illustrated in Figure 35.
DECOUPLING
CAPACITORS
In a typical application, all pins labeled AVEE or DVEE should
be connected directly to ground. All pins labeled AVCC,
DVCC, VTTI, or VTTO should be connected to 3.3 V, and
Pin AMUXVCC tied to 5 V. The supplies can also be powered
individually, but care must be taken to ensure that each stage of
the AD8191A is powered correctly.
AD8191A
Power Supply Bypassing
Rev. 0 | Page 26 of 28
AUXILIARY LINES
TMDS TRACES
07013-034
The AD8191A requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, DVCC, VTTI, and
VTTO) and ground to filter out supply noise. Generally, bypass
capacitors should be placed near the power pins and should
connect directly to the relevant supplies (without long intervening
traces). For example, to improve the parasitic inductance of the
power supply decoupling capacitors, minimize the trace length
between capacitor landing pads and the vias, as shown in Figure 34.
Figure 35. Example Placement of Power Supply
Decoupling Capacitors Around the AD8191A
AD8191A
OUTLINE DIMENSIONS
16.20
16.00 SQ
15.80
1.60 MAX
0.75
0.60
0.45
100
1
76
75
PIN 1
14.20
14.00 SQ
13.80
TOP VIEW
(PINS DOWN)
0.15
0.05
SEATING
PLANE
VIEW A
ROTATED 90° CCW
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
51
50
25
26
VIEW A
0.50
BSC
LEAD PITCH
0.27
0.22
0.17
COMPLIANT TO JEDEC STANDARDS MS-026-BED
051706-A
1.45
1.40
1.35
Figure 36. 100-Lead Low Profile Quad Flat Package [LQFP]
(ST-100)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8191AASTZ 1
AD8191AASTZ-RL1
AD8191A-EVALZ1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
100-Lead Low Profile Quad Flat Package [LQFP]
100-Lead Low Profile Quad Flat Package [LQFP], Reel
Evaluation Board
Z = RoHS Compliant Part.
Rev. 0 | Page 27 of 28
Package Option
ST-100
ST-100
Ordering Quantity
1,000
AD8191A
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips
I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07013-0-11/07(0)
Rev. 0 | Page 28 of 28