3.2 Gbps Single Buffered Mux/Demux Switch AD8153 FEATURES TRANSMIT PRE-EMPHASIS RECEIVE EQUALIZATION INPUT A EQ INPUT B EQ OUTPUT C RECEIVE EQUALIZATION OUTPUT A EQ INPUT C OUTPUT B TRANSMIT PRE-EMPHASIS 2:1 MULTIPLEXER/ 1:2 DEMULTIPLEXER CONTROL LOGIC AD8153 APPLICATIONS SEL BICAST LB_A LB_B LB_C MODE RESETB EQ_A/(SCL) EQ_B/(SDA) EQ_C PE_A/(I2C_A[0]) PE_B/(I2C_A[1]) PE_C/(I2C_A[2]) 06393-001 Single lane 2:1 mux/1:2 demux 3.2 Gbps to dc data rates Compensates over 40 inches of FR4 at 3.2 Gbps through Two levels of input equalization, or Four levels of output pre-emphasis Operates with ac- or dc-coupled differential I/O Low deterministic jitter, typically 16 ps p-p Low random jitter, typically 500 fs rms On-chip terminations Unicast or bicast on 1:2 demux function Loopback capability on all ports 3.3 V core supply Flexible I/O supply Low power, typically 200 mW in basic configuration1 32-lead LFCSP package −40°C to +85°C operating temperature range FUNCTIONAL BLOCK DIAGRAM Figure 1. Low cost redundancy switch SONET OC48/SDH16 and lower data rates Gigabit Ethernet over backplane Fibre Channel 1.06 Gbps and 2.12 Gbps over backplane Serial RapidIO PCI Express Gen 1 Infiniband over backplane GENERAL DESCRIPTION The AD8153 is an asynchronous, protocol agnostic, single-lane 2:1 switch with three differential CML inputs and three differential CML outputs. The AD8159, another member of the Xstream line of products, is suitable for similar applications that require more than one lane. The AD8153 is optimized for NRZ signaling with data rates of up to 3.2 Gbps per port. Each port offers two levels of input equalization and four levels of output pre-emphasis. The device consists of a 2:1 multiplexer and a 1:2 demultiplexer. There are three operating modes: pin mode, serial mode, and mixed mode. In pin mode, lane switching, equalization, and pre-emphasis are controlled exclusively using external pins. In serial mode, an I2C interface is used to control the device and to provide access to advanced features, such as additional preemphasis settings and output disable. In mixed mode, the user accesses the advanced features using I2C, but controls lane switching using the external pins. The main application of the AD8153 is to support redundancy on both the backplane side and the line interface side of a serial link. The device has unicast and bicast capability, so it is capable of supporting either 1 + 1 or 1:1 redundancy. Using a mixture of bicast and loopback modes, the AD8153 can also be used to test high speed serial links by duplicating the incoming data and transmitting it to the destination port and test equipment simultaneously. 1 Two ports active with no pre-emphasis. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. AD8153 TABLE OF CONTENTS Features .............................................................................................. 1 Transmit Pre-Emphasis ............................................................. 14 2 Applications....................................................................................... 1 I C Serial Control Interface........................................................... 15 Functional Block Diagram .............................................................. 1 Register Set.................................................................................. 15 General Description ......................................................................... 1 General Functionality ................................................................ 15 Revision History ............................................................................... 2 I2C Data Write............................................................................. 16 Specifications..................................................................................... 3 I2C Data Read.............................................................................. 17 I2C Timing Specifications............................................................ 4 Applications Information .............................................................. 18 Absolute Maximum Ratings............................................................ 5 PCB Design Guidelines ................................................................. 19 ESD Caution.................................................................................. 5 Interfacing to the AD8153............................................................. 20 Pin Configuration and Function Descriptions............................. 6 Termination Structures.............................................................. 20 Typical Performance Characteristics ............................................. 7 Input Compliance....................................................................... 20 Theory of Operation ...................................................................... 13 Output Compliance ................................................................... 21 Switch Configurations ............................................................... 13 Outline Dimensions ....................................................................... 22 Receive Equalization .................................................................. 14 Ordering Guide .......................................................................... 22 REVISION HISTORY 4/07—Revision 0: Initial Version. Rev. 0 | Page 2 of 24 AD8153 SPECIFICATIONS VCC = VTTI = VTTO = 3.3 V, VEE = 0 V, RL = 50 Ω, two outputs active with no pre-emphasis, data rate = 3.2 Gbps, ac-coupled, PRBS7 test pattern, VID = 800 mV p-p, TA = 25°C, unless otherwise noted.1 Table 1. Parameter DYNAMIC PERFORMANCE Data Rate/Channel (NRZ) Deterministic Jitter Random Jitter Propagation Delay Lane-to-Lane Skew Switching Time Output Rise/Fall Time INPUT CHARACTERISTICS Input Voltage Swing Input Voltage Range Input Capacitance OUTPUT CHARACTERISTICS Output Voltage Swing Output Voltage Range Output Current Output Current Output Capacitance TERMINATION CHARACTERISTICS Resistance Temperature Coefficient POWER SUPPLY Operating Range VCC VTTI VTTO Supply Current ICC II/O = ITTO + ITTI Supply Current ICC II/O = ITTO + ITTI THERMAL CHARACTERISTICS Operating Temperature Range θJA LOGIC INPUT CHARACTERISTICS Input High (VIH) Input Low (VIL) 1 Conditions Min Typ Max Unit 3.2 Gbps ps p-p fs ps ps ns ps 2000 VCC + 0.3 mV p-p V pF 900 Vcc + 0.6 16 28 2 mV p-p V mA mA pF 100 0.1 Ω Ω/°C DC Data rate = 3.2 Gbps, high EQ RMS, high EQ Input to output 16 500 640 55 5 85 20% to 80% Differential Common mode, VID = 800 mV p-p 200 VEE + 1.0 2 Differential, @ dc Single-ended absolute voltage level No pre-emphasis Maximum pre-emphasis, all ports 700 Vcc − 1.6 Differential VEE = 0 V VEE = 0 V VEE = 0 V Two outputs active, no pre-emphasis, 400 mV I/O swings (800 mV p-p differential) Three outputs active, maximum pre-emphasis, 400 mV I/O swings (800 mV p-p differential) 800 3.0 3.3 VCC VCC 3.6 V V V 27 26 31 32 35 39 mA mA 53 74 58 84 63 95 mA mA +85 °C °C/W VCC 0.8 V V −40 Still air 30.0 2.4 VEE VID: Input differential voltage swing. Rev. 0 | Page 3 of 24 AD8153 I2C TIMING SPECIFICATIONS SDA tf tLOW tSU;DAT tr tf tHD;STA tSP tBUF tr tHD;STA S tHD;DAT tSU;STO tSU;STA tHIGH Sr P S 06393-006 SCL Figure 2. I2C Timing Diagram Table 2. Parameter SCL Clock Frequency Hold Time for a Start Condition Set-up Time for a Repeated Start Condition Low Period of the SCL Clock High Period of the SCL Clock Data Hold Time Data Set-Up Time Rise Time for Both SDA and SCL Fall Time for Both SDA and SCL Set-Up Time for Stop Condition Bus Free Time Between a Stop Condition and a Start Condition Capacitance for Each I/O Pin Rev. 0 | Page 4 of 24 Symbol fSCL tHD;STA tSU;STA tLOW tHIGH tHD;DAT tSU;DAT tr tf tSU;STO tBUF Ci Min 0 0.6 0.6 1.3 0.6 0 10 1 1 0.6 1 5 Max 400+ – – – – – – 300 300 – – 7 Unit kHz μs μs μs μs μs ns ns ns μs ns pF AD8153 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VCC to VEE VTTI VTTO Internal Power Dissipation Differential Input Voltage Logic Input Voltage Storage Temperature Range Lead Temperature Junction Temperature Rating 3.7 V VCC + 0.6 V VCC + 0.6 V 4.1 W 2.0 V VEE − 0.3V < VIN < VCC + 0.6 V −65°C to +125°C 300°C 150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. 0 | Page 5 of 24 AD8153 32 31 30 29 28 27 26 25 VEE IPC INC PE_A/(I2C_A[0]) OPC ONC PE_B/(I2C_A[1]) PE_C/(I2C_A[2]) PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 PIN 1 INDICATOR AD8153 TOP VIEW 24 23 22 21 20 19 18 17 MODE RESETB SEL BICAST LB_A LB_B LB_C EQ_A/(SCL) NOTE EPAD NEEDS TO BE ELECTRICALLY CONNECTED TO VEE. 06393-002 VCC ONB OPB VCC INB IPB EQ_C EQ_B/(SDA) 9 10 11 12 13 14 15 16 VCC VTTO ONA OPA VTTI INA IPA VEE Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1, 9, 12 2 3 4 5 6 7 8, 32, EPAD 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Mnemonic VCC VTTO ONA OPA VTTI INA IPA VEE ONB OPB INB IPB EQ_C EQ_B/(SDA) EQ_A/(SCL) LB_C LB_B LB_A BICAST SEL RESETB MODE PE_C/(I2C_A[2]) PE_B/(I2C_A[1]) ONC OPC PE_A/(I2C_A[0]) INC IPC Type Power Power I/O I/O Power I/O I/O Power I/O I/O I/O I/O Control Control Control Control Control Control Control Control Control Control Control Control I/O I/O Control I/O I/O Description Positive Supply. Output Termination Supply. High Speed Output Complement. High Speed Output. Input Termination Supply. High Speed Input Complement. High Speed Input. Negative Supply. High Speed Output Complement. High Speed Output. High Speed Input Complement. High Speed Input. Port C Input Equalization Control. Port B Input Equalization Control/(I2C Data when MODE = 1). Port A Input Equalization Control/(I2C Clock when MODE = 1). Port C Loopback Enable. Port B Loopback Enable. Port A Loopback Enable. Bicast Enable. A/B Select. Configuration Registers Reset. Configuration Mode. 1 for Serial/Mixed Mode, 0 for Pin Mode. Port C Pre-Emphasis Control/(I2C Slave Address Bit 2 when MODE = 1). Port B Pre-Emphasis Control/(I2C Slave Address Bit 1 when MODE = 1). High Speed Output Complement. High Speed Output. Port A Pre-Emphasis Control/(I2C Slave Address Bit 0 when MODE = 1). High Speed Input Complement. High Speed Output. Rev. 0 | Page 6 of 24 AD8153 TYPICAL PERFORMANCE CHARACTERISTICS VCC = VTTI = VTTO =3.3 V, VEE = 0 V, RL = 50 Ω, two outputs active with no pre-emphasis, high EQ, data rate = 3.2 Gbps, ac-coupled, PRBS7 test pattern, VID = 800 mV p-p, TA = 25°C, unless otherwise noted. 2 PATTERN GENERATOR 50Ω CABLES 2 INPUT PIN OUTPUT 2 PIN 50Ω CABLES 2 50Ω AD8153 AC COUPLED EVALUATION BOARD TP1 TP2 HIGH-SPEED SAMPLING OSCILLOSCOPE 06393-014 DATA OUT 40ps/DIV Figure 6. 3.2 Gbps Output Eye, No Channel (TP2 from Figure 4) Figure 5. 3.2 Gbps Input Eye (TP1 from Figure 4) Rev. 0 | Page 7 of 24 06393-022 40ps/DIV 06393-021 150mV/DIV 150mV/DIV Figure 4. Standard Test Circuit (No Channel) AD8153 150mV/DIV DATA OUT 2 50Ω CABLES 2 FR4 TEST BACKPLANE 50Ω CABLES 2 2 DIFFERENTIAL STRIPLINE TRACES TP1 8mils WIDE, 8mils SPACE, 8mils DIELECTRIC HEIGHT TRACE LENGTHS = 20 INCHES, 40 INCHES 50Ω CABLES 2 50Ω AD8153 TP2 AC COUPLED EVALUATION BOARD TP3 HIGHSPEED SAMPLING OSCILLOSCOPE 06393-015 PATTERN GENERATOR INPUT OUTPUT 2 PIN PIN 40ps/DIV REFERENCE EYE DIAGRAM AT TP1 40ps/DIV 06393-026 40ps/DIV 06393-024 150mV/DIV 150mV/DIV Figure 7. Input Equalization Test Circuit Figure 10. 3.2 Gbps Output Eye, 20 Inch FR4 Input Channel, High EQ (TP3 from Figure 7) 40ps/DIV 06393-027 40ps/DIV 06393-025 150mV/DIV 150mV/DIV Figure 8. 3.2 Gbps Input Eye, 20 Inch FR4 Input Channel (TP2 from Figure 7) Figure 11. 3.2 Gbps Output Eye, 40 Inch FR4 Input Channel, High EQ (TP3 from Figure 7) Figure 9. 3.2 Gbps Input Eye, 40 Inch FR4 Input Channel (TP2 from Figure 7) Rev. 0 | Page 8 of 24 AD8153 150mV/DIV DATA OUT 2 50Ω CABLES 2 50Ω CABLES 2 INPUT OUTPUT 2 PIN PIN AD8153 PATTERN GENERATOR 2 50Ω CABLES 2 50Ω DIFFERENTIAL STRIPLINE TRACES TP2 8mils WIDE, 8mils SPACE, 8mils DIELECTRIC HEIGHT TRACE LENGTHS = 20 INCHES, 40 INCHES AC COUPLED EVALUATION BOARD TP3 HIGHSPEED SAMPLING OSCILLOSCOPE 06393-013 TP1 FR4 TEST BACKPLANE 40ps/DIV REFERENCE EYE DIAGRAM AT TP1 40ps/DIV 06393-019 40ps/DIV 06393-017 150mV/DIV 150mV/DIV Figure 12. Output Pre-Emphasis Test Circuit Figure 15. 3.2 Gbps Output Eye, 20 Inch FR4 Output Channel, PE = 2 (TP3 from Figure 12) 40ps/DIV Figure 14. 3.2 Gbps Output Eye, Pre-Channel, PE = 3 (TP2 from Figure 12) 06393-020 40ps/DIV 06393-018 150mV/DIV 150mV/DIV Figure 13. 3.2 Gbps Output Eye, Pre-Channel, PE = 2 (TP2 from Figure 12) Figure 16. 3.2 Gbps Output Eye, 40 Inch FR4 Output Channel, PE = 3 (TP3 from Figure 12) Rev. 0 | Page 9 of 24 AD8153 80 80 70 70 PE = 1 DETERMINISTIC JITTER (ps) LOW EQ 50 40 HIGH EQ 30 20 60 PE = 3 40 30 20 10 10 30 10 20 FR4 INPUT CHANNEL LENGTH (IN) 0 40 0 06393-028 0 PE = 2 50 Figure 17. Deterministic Jitter vs. FR4 Input Channel Length 0 10 20 30 FR4 OUTPUT CHANNEL LENGTH (IN) Figure 20. Deterministic Jitter vs. FR4 Output Channel Length 80 20 SAMPLES: 557k 70 60 JITTER (ps) 40 06393-041 DETERMINISTIC JITTER (ps) PE = 0 60 15 50 40 10 DETERMINISTIC JITTER 30 20 5 RANDOM JITTER 1.5 2.0 2.5 3.0 DATA RATE (Gbps) 3.5 4.0 0 –2ps 06393-038 0 1.0 80 70 70 60 60 50 50 JITTER (ps) 80 40 30 DETERMINISTIC JITTER 20 0.0s 1ps 2ps Figure 21. Random Jitter Histogram, 3.2 Gbps 40 30 20 DETERMINISTIC JITTER 10 10 RANDOM JITTER 0 0.2 0.4 1.4 1.6 0.6 0.8 1.0 1.2 DIFFERENTIAL INPUT SWING (V) RANDOM JITTER 1.8 2.0 0 0.8 Figure 19. Jitter vs. Differential Input Swing 1.3 1.8 2.3 2.8 3.3 INPUT COMMON-MODE VOLTAGE (V) Figure 22. Jitter vs. Input Common-Mode Voltage Rev. 0 | Page 10 of 24 3.8 06393-035 0 06393-032 JITTER (ps) Figure 18. Jitter vs. Data Rate –1ps 06393-039 10 80 80 70 70 60 60 50 50 JITTER (ps) 40 30 DETERMINISTIC JITTER 20 40 30 DETERMINISTIC JITTER 20 10 10 3.2 3.3 VCC (V) 3.4 3.5 3.6 0 2 2.2 2.4 2.6 2.8 3.0 VTTO (V) 3.2 3.4 3.6 06393-031 3.1 06393-033 0 3.0 100 06393-029 RANDOM JITTER RANDOM JITTER 100 06393-040 JITTER (ps) AD8153 Figure 26. Jitter vs. Output Termination Voltage Figure 23. Jitter vs. Core Supply Voltage 100 80 70 95 RISE/FALL TIME (ps) JITTER (ps) 60 50 40 30 20 DETERMINISTIC JITTER 90 85 80 10 RANDOM JITTER –20 0 20 40 60 TEMPERATURE (°C) 80 100 75 –40 06393-037 0 –40 650 650 PROPAGATION DELAY (ps) 700 600 550 3.2 3.3 VCC (V) 3.4 3.5 3.6 20 40 60 TEMPERATURE (°C) 80 600 550 500 –40 06393-030 PROPAGATION DELAY (ps) 700 3.1 0 Figure 27. Rise/Fall Time vs. Temperature Figure 24. Jitter vs. Temperature 500 3.0 –20 Figure 25. Propagation Delay vs. Core Supply Voltage –20 0 20 40 60 TEMPERATURE (°C) 80 Figure 28. Propagation Delay vs. Temperature Rev. 0 | Page 11 of 24 AD8153 900 900 800 800 700 700 600 500 400 300 600 500 400 300 200 200 100 100 3.1 3.2 3.3 VCC (V) 3.4 3.5 3.6 0 06393-034 0 3.0 0 0.5 1.0 1.5 2.0 2.5 DATA RATE (Gbps) 3.0 Figure 30. Eye Height vs. Data Rate Figure 29. Eye Height vs. Core Supply Voltage Rev. 0 | Page 12 of 24 3.5 4.0 06393-036 EYE HEIGHT (mV) 1000 EYE HEIGHT (mV) 1000 AD8153 THEORY OF OPERATION The AD8153 consists of a 2:1 multiplexer and a 1:2 demultiplexer. There are three operating modes: pin mode, serial mode, and mixed mode. In pin mode, lane switching, equalization, and pre-emphasis are controlled using external pins. In serial mode, an I2C interface is used to control the device and to provide access to advanced features, such as additional pre-emphasis settings and output disable. In mixed mode, the user accesses the advanced features using I2C but controls lane switching using external pins. side, the device relays received data on either Input Port A or Input Port B to Output Port C, depending on the state of the SEL bit. When bicast mode is off, the outputs of either Port A or Port B are in an idle state. In the idle state, the output tail current is set to 0, and the P and N sides of the lane are pulled up to the output termination voltage through the on-chip termination resistors. SWITCH CONFIGURATIONS The device also supports loopback on all ports, illustrated in Figure 31. Enabling loopback on any port overrides configurations set by the BICAST and SEL control bits. Table 5 summarizes the possible switch configurations. On the demultiplexer side, the AD8153 relays received data on Input Port C to Output Port A and/or Output Port B, depending on the state of the BICAST and SEL bits. On the multiplexer The AD8153 output disable feature can be used to force an output into the idle (powered-down) state. This feature is only accessible through the serial control interface. OUTPUT A 1:2 DEMUX INPUT C OUTPUT B PORT A LOOPBACK PORT B LOOPBACK PORT C LOOPLOCK INPUT A 2:1 MUX OUTPUT C 06393-003 INPUT B Figure 31. Loopback Configurations Table 5. Switch Configurations LB_A 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 LB_B 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 LB_C 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 SEL 0 0 1 1 0 X 1 0 1 1 0 1 X 0 0 1 0 BICAST 0 1 0 1 0 1 0 X 0 1 X 0 1 0 1 X 0 Rev. 0 | Page 13 of 24 Output A Input C Input C Idle Input C Input C Input C Idle Input C Idle Input C Input C Idle Input C Input A Input A Input A Input A Output B Idle Input C Input C Input C Idle Input C Input C Input B Input B Input B Input B Input B Input B Idle Input C Input C Idle Output C Input A Input A Input B Input B Input C Input C Input C Input A Input B Input B Input C Input C Input C Input A Input A Input B Input C AD8153 LB_A 1 1 1 1 1 LB_B 0 0 1 1 1 LB_C 1 1 0 0 1 SEL X 1 0 1 X BICAST 1 X X X X Output A Input A Input A Input A Input A Input A Output B Input C Input C Input B Input B Input B Output C Input C Input C Input A Input B Input C RECEIVE EQUALIZATION TRANSMIT PRE-EMPHASIS In backplane applications, the AD8153 needs to compensate for signal degradation caused by long traces. The device supports two levels of input equalization, configured on a per-port basis. Table 6 summarizes the high-frequency asymptotic gain boost for each setting. Transmitter pre-emphasis levels can be set by pin control or through the control registers when using the I2C interface. Pin control allows two settings of PE. The control registers provide two additional settings. Table 6. Receive Equalization Settings EQ_A/B/C 0 1 EQ Boost 6 dB 12 dB Table 7. Pre-Emphasis Settings Serial Mode PE_A/B/C Setting 0 1 2 3 Rev. 0 | Page 14 of 24 Pin Mode PE_A/B/C 0 N/A 1 N/A PE Boost (%) 0 25 50 75 PE Boost (dB) 0 1.9 3.5 4.9 AD8153 I2C SERIAL CONTROL INTERFACE pins or the internal register set. The source of the control is selected using the mask bits (Register 0x00). If a mask bit is set to 0, the external pin acts as the source for that specific control. If a mask bit is set to 1, the associated internal register acts as the source for that specific control. As an example, if Register 0x00 were set to the value 0x0C, the SEL and LB_C controls would come from the internal register set (Bit 0 of Register 0x04 and Bit 3 of Register 0x03, respectively), and the BICAST, LB_A, and LB_B controls would come from the external pins. REGISTER SET The AD8153 can be controlled in one of three modes: pin mode, serial mode, and mixed mode. In pin mode, the AD8153 control is derived from the package pins, whereas in serial mode a set of internal registers controls the AD8153. There is also a mixed mode where switching is controlled via external pins, and equalization and pre-emphasis are controlled via the internal registers. The methods for writing data to and reading data from the AD8153 are described in the I2C Data Write section and the I2C Data Read section. GENERAL FUNCTIONALITY The mode is controlled via the MODE pin. To set the part in pin mode, MODE should be driven low to VEE. When MODE is driven high to VCC, the part is set to serial or mixed mode. In pin mode, all controls are derived from the external pins. In serial mode, each channel’s equalization and pre-emphasis are controlled only through the registers, as described in Table 8. Additionally, further functionality is available in serial mode as each channel’s output can be enabled/disabled with the Output Enable control bits, which is not possible in pin mode. To change the switching in the AD8153 to serial mode, the mask bits (Register 0x00) must be set to 1 by writing the value 0x1F to this register, as explained in the following sections. Once all the mask bits are set to 1, switching is controlled via the LB_A, LB_B, LB_C, SEL, and BICAST bits in the register set. In mixed mode, each channel’s equalization and pre-emphasis are controlled through the registers as described above. The switching, however, can be controlled using either the external The AD8153 register set is controlled through a 2-wire I2C interface. The AD8153 acts only as an I2C slave device. Therefore, the I2C bus in the system needs to include an I2C master to configure the AD8153 and other I2C devices that may be on the bus. When the MODE pin is set to a Logic 1, data transfers are controlled through the use of the two I2C wires: the input clock pin, SCL, and the bidirectional data pin, SDA. The AD8153 I2C interface can be run in the standard (100 kHz) and fast (400 kHz) modes. The SDA line only changes value when the SCL pin is low with two exceptions. To indicate the beginning or continuation of a transfer, the SDA pin is driven low while the SCL pin is high, and to indicate the end of a transfer, the SDA line is driven high while the SCL line is high. Therefore, it is important to control the SCL clock to only toggle when the SDA line is stable unless indicating a start, repeated start, or stop condition. Table 8. Register Map Address 00000000 (0x00) 00000001 (0x01) 00000010 (0x02) 00000011 (0x03) 0000100 (0x04) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 BICAST MASK SEL MASK LB_C MASK LB_B MASK LB_A MASK OUTPUT DISABLE A LB_A EQ_A PE_A [1] PE_A [0] OUTPUT DISABLE B LB_B EQ_B PE_B [1] PE_B [0] OUTPUT DISABLE C LB_C EQ_C PE_C [1] PE_C [0] BICAST SEL Rev. 0 | Page 15 of 24 Default 00000000 (0x00) 00000000 (0x00) 00000000 (0x00) 00000000 (0x00) 00000000 (0x00) AD8153 I2C DATA WRITE To write data to the AD8153 register set, a microcontroller, or any other I2C master, needs to send the appropriate control signals to the AD8153 slave device. The steps that need to be followed are listed below, where the signals are controlled by the I2C master unless otherwise specified. A diagram of the procedure is shown in Figure 32. 1. Send a start condition (while holding the SCL line high, pull the SDA line low). 2. Send the AD8153 part address (seven bits) whose upper four bits are the static value b1001 and whose lower three bits are controlled by the input pins I2C_A[2:0]. This transfer should be MSB first. 3. Send the write indicator bit (0). 4. Wait for the AD8153 to acknowledge the request. 5. Send the register address (eight bits) to which data is to be written. This transfer should be MSB first. 6. Wait for the AD8153 to acknowledge the request. 7. Send the data (eight bits) to be written to the register whose address was set in Step 5. This transfer should be MSB first. 8. Wait for the AD8153 to acknowledge the request. 9. Send a stop condition (while holding the SCL line high, pull the SDA line high) and release control of the bus. 10. Send a repeated start condition (while holding the SCL line high, pull the SDA line low) and continue with Step 2 in this procedure to perform another write. 11. Send a repeated start condition (while holding the SCL line high, pull the SDA line low) and continue with Step 2 of the read procedure (in the I2C Data Read section) to perform a read from another address. 12. Send a repeated start condition (while holding the SCL line high, pull the SDA line low) and continue with step 8 of the read procedure (in the I2C Data Read section) to perform a read from the same address set in Step 5. The AD8153 write process is shown in Figure 32. The SCL signal is shown along with a general write operation and a specific example. In the example, data 0x92 is written to Address 0x6D of an AD8153 part with a part address of 0x4B. The part address is seven bits wide and is composed of the AD8153 static upper four bits (b1001) and the pin programmable lower three bits (I2C_ADDR[2:0]). In this example, the I2C_ADDR bits are set to b011. In Figure 32, the corresponding step number is visible in the circle under the waveform. The SCL line is driven by the I2C master and never by the AD8153 slave. As for the SDA line, the data in the shaded polygons is driven by the AD8153, whereas the data in the nonshaded polygons is driven by the I2C master. The end phase case shown is that of 9a. It is important to note that the SDA line only changes when the SCL line is low, except for the case of sending a start, stop, or repeated start condition, Step 1 and Step 9 in this case. SCL SDA (GENERAL CASE) START FIXED PART ADDR ADDR [2:0] RW ACK REGISTER ADDR ACK DATA ACK STOP 1 2 2 3 4 5 Figure 32. I2C Write Diagram Rev. 0 | Page 16 of 24 6 7 8 9a 06393-004 SDA (EXAMPLE) AD8153 I2C DATA READ 12. Acknowledge the data. To read data from the AD8153 register set, a microcontroller, or any other I2C master, needs to send the appropriate control signals to the AD8153 slave device. The steps to be followed are listed below, where the signals are controlled by the I2C master unless otherwise specified. A diagram of the procedure can be seen in Figure 33. 13. Send a stop condition (while holding the SCL line high, pull the SDA line high) and release control of the bus. 1. Send a start condition (while holding the SCL line high, pull the SDA line low). 15. Send a repeated start condition (while holding the SCL line high, pull the SDA line low) and continue with Step 2 of this procedure to perform a read from another address. 14. Send a repeated start condition (while holding the SCL line high, pull the SDA line low) and continue with Step 2 of the write procedure (see the I2C Data Write section) to perform a write. 2. Send the AD8153 part address (seven bits) whose upper four bits are the static value b1001 and whose lower three bits are controlled by the input pins I2C_ADDR[2:0]. This transfer should be MSB first. 16. Send a repeated start condition (while holding the SCL line high, pull the SDA line low) and continue with Step 8 of this procedure to perform a read from the same address. 3. Send the write indicator bit (0). The AD8153 read process is shown in Figure 33. The SCL signal is shown along with a general read operation and a specific example. In the example, Data 0x49 is read from Address 0x6D of an AD8153 part with a part address of 0x4B. The part address is seven bits wide and is composed of the AD8153 static upper four bits (b1001) and the pin programmable lower three bits (I2C_ADDR[2:0]). In this example, the I2C_ADDR bits are set to b011. In Figure 33, the corresponding step number is visible in the circle under the waveform. The SCL line is driven by the I2C master and never by the AD8153 slave. As for the SDA line, the data in the shaded polygons is driven by the AD8153, whereas the data in the nonshaded polygons is driven by the I2C master. The end phase case shown is that of 13a. 4. Wait for the AD8153 to acknowledge the request. 5. Send the register address (eight bits) from which data is to be read. This transfer should be MSB first. The register address is kept in memory in the AD8153 until the part is reset or the register address is written over with the same procedure (Step 1 to Step 6). 6. Wait for the AD8153 to acknowledge the request. 7. Send a repeated start condition (while holding the SCL line high, pull the SDA line low). 8. Send the AD8153 part address (seven bits) whose upper four bits are the static value b1001 and whose lower three bits are controlled by the input pins I2C_ADDR[1:0]. This transfer should be MSB first. It is important to note that the SDA line only changes when the SCL line is low, except for the case of sending a start, stop, or repeated start condition, as in Step 1, Step 7, and Step 13. In Figure 33, A is the same as ACK in Figure 32. Equally, Sr represents a repeated start where the SDA line is brought high before SCL is raised. SDA is then dropped while SCL is still high. 9. Send the read indicator bit (1). 10. Wait for the AD8153 to acknowledge the request. 11. The AD8153 then serially transfers the data (eight bits) held in the register indicated by the address set in Step 5. SCL SDA (GENERAL CASE) START FIXED PART ADDR ADDR R A [2:0] W REGISTER ADDR A Sr FIXED PART ADDR ADDR [2:0] R W A DATA A STOP 11 12 13a 1 2 2 3 4 5 6 7 2 Figure 33. I C Read Diagram Rev. 0 | Page 17 of 24 8 8 9 10 06393-005 SDA (EXAMPLE) AD8153 APPLICATIONS INFORMATION The main application of the AD8153 is to support redundancy on both the backplane side and the line interface side of a serial link. Figure 34 illustrates redundancy in a typical backplane system. Each line card is connected to two switch fabrics (primary and redundant). The device can be configured to support either 1 + 1 or 1:1 redundancy. PHYSICAL INTERFACE Another application for the AD8153 is in test equipment for evaluating high speed serial links. Figure 36 illustrates a possible application of the AD8153 in a simple link tester. PRIMARY SWITCH FABRIC DIGITAL ENGINE AD8153 LINE CARDS DIGITAL ENGINE AD8153 FABRIC CARDS BACKPLANE Figure 34. Switch Redundancy Application SFP CDR SFP CDR PROCESSING ENGINE/CROSSBAR/ BACKPLANE 06393-008 AD8153 Figure 35. Line Interface Redundancy Application DUT CONNECTOR FPGA 06393-009 PROTOCOL ANALYZER CONNECTOR AD8153 Figure 36. Test Equipment Application Rev. 0 | Page 18 of 24 06393-007 PHYSICAL INTERFACE REDUNDANT SWITCH FABRIC AD8153 PCB DESIGN GUIDELINES Transmission Lines Proper RF PCB design techniques must be used for optimal performance. Power Supply Connections and Ground Planes Use of one low impedance ground plane is recommended. The VEE pins should be soldered directly to the ground plane to reduce series inductance. If the ground plane is an internal plane and connections to the ground plane are made through vias, multiple vias can be used in parallel to reduce the series inductance. The exposed pad should be connected to the VEE plane using plugged vias so that solder does not leak through the vias during reflow. Use of a 10 μF electrolytic capacitor between VCC and VEE is recommended at the location where the 3.3 V supply enters the PCB. It is recommended that 0.1 μF and 1 nF ceramic chip capacitors be placed in parallel at each supply pin for high frequency power supply decoupling. When using 0.1 μF and 1 nF ceramic chip capacitors, they should be placed between the IC power supply pins (VCC, VTTI, VTTO) and VEE, as close as possible to the supply pins. Use of 50 Ω transmission lines is required for all high frequency input and output signals to minimize reflections. It is also necessary for the high speed pairs of differential input traces to be matched in length, as well as the high speed pairs of differential output traces, to avoid skew between the differential traces. Soldering Guidelines for Chip Scale Package The lands on the 32-lead LFCSP are rectangular. The printed circuit board pad for these should be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. The land should be centered on the pad. This ensures that the solder joint size is maximized. The bottom of the chip scale package has a central exposed pad. The pad on the printed circuit board should be at least as large as this exposed pad. The user must connect the exposed pad to VEE using plugged vias so that solder does not leak through the vias during reflow. This ensures a solid connection from the exposed pad to VEE. By using adjacent power supply and GND planes, excellent high frequency decoupling can be realized by using close spacing between the planes. This capacitance is given by CPLANE = 0.88εr A/d (pF) where: εr is the dielectric constant of the PCB material. A is the area of the overlap of power and GND planes (cm2). d is the separation between planes (mm). For FR4, εr = 4.4 and 0.25 mm spacing, C ~15 pF/cm2. Rev. 0 | Page 19 of 24 AD8153 INTERFACING TO THE AD8153 AC Coupling TERMINATION STRUCTURES To determine the best strategy for connecting to the high speed pins of the AD8153, the user must first be familiar with the onchip termination structures. The AD8153 contains two types of these structures: one type for input ports and one type for output ports (see Figure 37 and Figure 38). VCC One way to simplify the input circuit and make it compatible with a wide variety of driving devices is to use ac coupling. This has the effect of isolating the dc common-mode levels of the driver and the AD8153 input circuitry. AC coupling requires a capacitor in series with each single-ended input signal, as shown in Figure 39. This should be done in a manner that does not interfere with the high speed signal integrity of the PCB. VCC VTTI 55Ω VCC VTTI 55Ω 50Ω 50Ω IPX CP CN 1173Ω IP IN 55Ω 55Ω 1173Ω INX VEE DRIVER Figure 37. Receiver Simplified Diagram Figure 39. AC-Coupling Input Signal of AD8153 When ac coupling is used, the common-mode level at the input of the device is equal to VTTI. The single-ended input signal swings above and below VTTI equally. The user can then use the specifications in Table 1 to determine the input signal swing levels that satisfy the input range of the AD8153. VCC VTTO 50Ω 50Ω OPX VIP VEE 06393-042 06393-010 AD8153 If dc coupling is required, determining the input commonmode level is less straightforward because the configuration of the driver must also be considered. In most cases, the user would set VTTI on the AD8153 to the same level as the driver output termination voltage. This prevents a continuous dc current from flowing between the two supply nets. As a practical matter, both devices can be terminated to the same physical supply net. ONX IT VEE 06393-011 VIN Figure 38. Transmitter Simplified Diagram For input ports, the termination structure consists of two 55 Ω resistors connected to a termination supply and an 1173 Ω resistor connected across the differential inputs, the latter being a result of the finite differential input impedance of the equalizer. For output ports, there are two 50 Ω resistors connected to the termination supply. Note that the differential input resistance for both structures is the same, 100 Ω. INPUT COMPLIANCE The range of allowable input voltages is determined by the fundamental limitations of the active input circuitry. This range of signals is normally a function of the common-mode level of the input signal, the signal swing, and the supply voltage. For a given input signal swing, there is a range of common-mode voltages that keeps the high and low voltage excursions within acceptable limits. Similarly, for a given common-mode input voltage, there is a maximum acceptable input signal swing. There is also a minimum signal swing that the active input circuitry can resolve reliably. The specifications are found in Table 1. Consider the following example: a driver is dc-coupled to the input of the AD8153. The AD8153 input termination voltage (VTTI) and the driver output termination voltage (VTTOD) are both set to the same level; that is, VTTI = VTTOD = 3.3 V. If an 800 mV differential p-p swing is desired, the total output current of the driver is 16 mA. At balance, the output current is divided evenly between the two sides of the differential signal path, 8 mA to each side. This 8 mA of current flows through the parallel combination of the 55 Ω input termination resistor on the AD8153 and the 50 Ω output termination resistor on the driver, resulting in a common-mode level of VTTI − 8 mA × (50 Ω || 55 Ω) = VTTI − 209 mV The user can then determine the allowable range of values for VTTI that meets the input compliance range based on an 800 mV p-p differential swing. Rev. 0 | Page 20 of 24 AD8153 Figure 40 is a graphical depiction of the single-ended waveform at the output of the AD8153. The common-mode level (VOCM) and the amplitude (VOSE) of this waveform are a function of the output tail current (IT), the output termination supply voltage (VTTO), the topology of the far-end receiver, and whether ac- or dc-coupling is used. Keep in mind that the output tail current varies with the pre-emphasis level. The user must ensure that the high (VH) and low (VL) voltage excursions at the output are within the single-ended absolute voltage range limits as specified in Table 1. Failure to understand the implications of output signal levels and the choice of ac- or dc-coupling may lead to transistor saturation and poor transmitter performance. Table 9 shows an example calculation of the output levels for the typical case, where VCC = VTTO = 3.3 V, with 50 Ω far-end terminations to a 3.3 V supply. VTTO VH VOCM VOSE-DC VOSE-BOOST VL ~320ps 06393-012 OUTPUT COMPLIANCE Figure 40. Single-Ended Output Waveform Table 9. Output Voltage Levels PE Setting 0 1 2 3 IT (mA) 16 20 24 28 VOSE-DC (mV p-p) 400 400 400 400 VOSE-BOOST (mV p-p) 400 500 600 700 VOCM (V) 3.1 3.05 3 2.95 DC-Coupled VH (V) 3.3 3.3 3.3 3.3 VL (V) 2.9 2.8 2.7 2.6 VOCM (V) 2.9 2.8 2.7 2.6 AC-Coupled VH (V) 3.1 3.05 3 2.95 Table 10. Symbol Definitions Symbol VOSE-DC Formula VOSE-BOOST IT × 25Ω VOCM (dc-coupled) VTTO − VOCM (ac-coupled) IT PE = 0 VTTO × 25Ω IT × 25Ω 2 I − T × 50Ω 2 Definition Single-ended output voltage swing after settling Boosted single-ended output voltage swing Common-mode voltage when the output is dc-coupled Common-mode voltage when the output is ac-coupled VH VOCM + VOSE-BOOST/2 High single-ended output voltage excursion VL VOCM - VOSE-BOOST/2 Low single-ended output voltage excursion Rev. 0 | Page 21 of 24 VL (V) 2.7 2.55 2.4 2.25 AD8153 OUTLINE DIMENSIONS 5.00 BSC SQ PIN 1 INDICATOR 0.60 MAX 0.60 MAX TOP VIEW 0.50 BSC 4.75 BSC SQ 0.50 0.40 0.30 1.00 0.85 0.80 12° MAX SEATING PLANE 25 24 32 1 PIN 1 INDICATOR 2.85 2.70 SQ 2.55 *EXPOSED PAD (BOT TOM VIEW) 17 16 9 8 0.20 MIN 3.50 REF 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.30 0.25 0.18 0.20 REF COPLANARITY 0.08 032807-A COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2 *THE AD8153 HAS A CONDUCTIVE HEAT SLUG TO HELP DISSIPATE HEAT AND ENSURE RELIABLE OPERATION OF THE DEVICE OVER THE FULL INDUSTRIAL TEMPERATURE RANGE. THE SLUG IS EXPOSED ON THE BOTTOM OF THE PACKAGE AND ELECTRICALLY CONNECTED TO VEE. IT IS RECOMMENDED THAT NO PCB SIGNAL TRACES OR VIAS BE LOCATED UNDER THE PACKAGE THAT COULD COME IN CONTACT WITH THE CONDUCTIVE SLUG. Figure 41. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 5 mm × 5 mm Body, Very Thin Quad (CP-32-8) Dimensions shown in millimeters ORDERING GUIDE Model AD8153ACPZ 1 AD8153ACPZ-RL71 AD8153-EVALZ1 1 Temperature Range −40°C to +85°C −40°C to +85°C Package Description 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] Evaluation Board Z = RoHS Compliant Part. Rev. 0 | Page 22 of 24 Package Option CP-32-8 CP-32-8 AD8153 NOTES Rev. 0 | Page 23 of 24 AD8153 NOTES ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06393-0-4/07(0) Rev. 0 | Page 24 of 24