AD ADN8102ACPZ-R7

3.75 Gbps Quad Bidirectional
CX4 Equalizer
ADN8102
Optimized for dc to 3.75 Gbps data
Programmable input equalization
Up to 22 dB boost at 1.875 GHz
Compensates up to 30 meters of CX4 cable up to 3.75 Gbps
Compensates up to 40 inches of FR4 up to 3.75 Gbps
Programmable output pre-emphasis/de-emphasis
Up to 12 dB boost at 1.875 GHz (3.75 Gbps)
Compensates up to 15 meters of CX4 cable up to 3.75 Gbps
Compensates up to 40 inches of FR4 up to 3.75 Gbps
Flexible 1.8 V to 3.3 V core supply
Per lane P/N pair inversion for routing ease
Low power: 125 mW/channel up to 3.75 Gbps
DC- or ac-coupled differential CML inputs
Programmable CML output levels
50 Ω on-chip termination
Loss-of-signal detection
Temperature range operation: −40°C to +85°C
Supports 8b10b, scrambled, or uncoded NRZ data
I2C control interface
64-lead LFSCP (QFN) package
APPLICATIONS
10GBase-CX4
HiGig™
InfiniBand
1×, 2× Fibre Channel
XAUI
Gigabit Ethernet over backplane or cable
CPRI™
50 Ω cables
FUNCTIONAL BLOCK DIAGRAM
LOS_B
ADN8102
RECEIVE
EQUALIZATION
Ix_B[3:0]
TRANSMIT
PRE-EMPHASIS
EQ
2:1
PE
LOS_A
LB
RECEIVE
EQUALIZATION
TRANSMIT
PRE-EMPHASIS
Ox_A[3:0]
ADDR[1:0]
SCL
SDA
RESET
Ox_B[3:0]
PE
EQ
2:1
CONTROL LOGIC
Ix_A[3:0]
EQ_A[1:0]
PE_A[1:0]
EQ_B[1:0]
PE_B[1:0]
ENA
ENB
07060-001
FEATURES
Figure 1.
GENERAL DESCRIPTION
The ADN8102 is a quad bidirectional CX4 cable/backplane
equalizer with eight differential PECL-/CML-compatible inputs
with programmable equalization and eight differential CML
outputs with programmable output levels and pre-emphasis or
de-emphasis. The operation of this device is optimized for NRZ
data at rates up to 3.75 Gbps.
The receive inputs provide programmable equalization to
compensate for up to 30 meters of CX4 cable (24 AWG) or
40 inches of FR4, and programmable pre-emphasis to compensate
for up to 15 meters of CX4 cable (24 AWG) or 40 inches of FR4
at 3.75 Gbps. Each channel also provides programmable loss-ofsignal detection and loopback capability for system testing and
debugging.
The ADN8102 is controlled through toggle pins, an I2C® control
interface that provides more flexible control, or a combination of
both. Every channel implements an asynchronous path supporting
dc to 3.75 Gbps NRZ data, fully independent of other channels. The
ADN8102 has low latency and very low channel-to-channel skew.
The main application for the ADN8102 is to support switching
in chassis-to-chassis applications over CX4 or InfiniBand® cables.
The ADN8102 is packaged in a 9 mm × 9 mm 64-lead LFCSP
(QFN) package and operates from −40°C to +85°C.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
ADN8102
TABLE OF CONTENTS
Features .............................................................................................. 1 Lane Inversion ............................................................................ 18 Applications ....................................................................................... 1 Loopback ..................................................................................... 19 Functional Block Diagram .............................................................. 1 Transmitters ................................................................................ 20 General Description ......................................................................... 1 Selective Squelch and Disable ................................................... 25 Revision History ............................................................................... 2 I C Control Interface ...................................................................... 26 Specifications..................................................................................... 3 Serial Interface General Functionality..................................... 26 Timing Specifications .................................................................. 5 I2C Interface Data Transfers—Data Write .............................. 26 Absolute Maximum Ratings............................................................ 6 I2C Interface Data Transfers—Data Read ............................... 27 ESD Caution .................................................................................. 6 PCB Design Guidelines ................................................................. 28 Pin Configuration and Function Descriptions ............................. 7 Power Supply Connections and Ground Planes .................... 28 Typical Performance Characteristics ............................................. 9 Transmission Lines..................................................................... 28 Theory of Operation ...................................................................... 16 Soldering Guidelines for Chip Scale Package ............................. 28 Introduction ................................................................................ 16 Register Map ................................................................................... 29 Receivers ...................................................................................... 16 Outline Dimensions ....................................................................... 31 Equalization Settings .................................................................. 17 Ordering Guide .......................................................................... 31 2
REVISION HISTORY
8/08—Rev. 0 to Rev. A
Changes to Features Section............................................................ 1
Changes to Loss of Signal/Signal Detect Section ....................... 18
Added Recommended LOS Settings Section .............................. 18
Deleted Figure 39; Renumbered Sequentially ............................ 18
Exposed Paddle Notation Added to Outline Dimensions ........ 31
5/08—Revision 0: Initial Version
Rev. A | Page 2 of 32
ADN8102
SPECIFICATIONS
VCC = 1.8 V, VEE = 0 V, VTTI = VTTO = VCC, RL = 50 Ω, differential output swing = 800 mV p-p differential, 3.75 Gbps, PRBS 27 − 1,
TA = 25°C, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
Maximum Data Rate/Channel (NRZ)
Deterministic Jitter
Random Jitter
Residual Deterministic Jitter
With Input Equalization
With Output Pre-Emphasis
Output Rise/Fall Time
Propagation Delay
Channel-to-Channel Skew
OUTPUT PRE-EMPHASIS
Equalization Method
Maximum Boost
Pre-Emphasis Tap Range
INPUT EQUALIZATION
Minimum Boost
Maximum Boost
Number of Equalization Settings
Gain Step Size
INPUT CHARACTERISTICS
Input Voltage Swing
Input Voltage Range
Input Resistance
Input Return Loss
OUTPUT CHARACTERISTICS
Output Voltage Swing
Conditions
Min
Typ
Max
3.75
Unit
Data rate < 3.75 Gbps; BER = 1 × 10−12
VCC = 1.8 V
33
1.5
Gbps
ps p-p
ps rms
Data rate < 3.25 Gbps; 0 inches to 40 inches FR4
Data rate < 3.25 Gbps; 0 meters to 30 meters CX4
Data rate < 3.75 Gbps; 0 inches to 40 inches FR4
Data rate < 3.75 Gbps; 0 meters to 30 meters CX4
Data rate < 3.25 Gbps; 0 inches to 40 inches FR4
Data rate < 3.25 Gbps; 0 meters to 15 meters CX4
Data rate < 3.75 Gbps; 0 inches to 40 inches FR4
Data rate < 3.75 Gbps; 0 meters to 15 meters CX4
20% to 80%
0.20
0.19
0.24
0.21
0.13
0.37
0.14
0.41
75
1
50
UI
UI
UI
UI
UI
UI
UI
UI
ps
ns
ps
6
12
2
12
dB
dB
mA
mA
1.5
22
8
2.5
dB
dB
1-tap programmable pre-emphasis
800 mV p-p output swing
200 mV p-p output swing
Minimum
Maximum
EQBY = 1
Maximum boost occurs at 1.875 GHz
Differential, VICM 1 = VCC − 0.6 V
Single-ended absolute voltage level, VL minimum
Single-ended absolute voltage level, VH maximum
Single-ended
Measured at 2.5 GHz
DC, differential, PE = 0, default, VCC = 1.8 V
DC, differential, PE = 0, default, VCC = 3.3 V
DC, differential, PE = 0, minimum output level, 2 VCC = 1.8 V
DC, differential, PE = 0, minimum output level,2 VCC = 3.3 V
DC, differential, PE = 0, maximum output level,2 VCC = 1.8 V
DC, differential, PE = 0, maximum output level,2 VCC = 3.3 V
Rev. A | Page 3 of 32
300
45
635
dB
2000
VEE + 0.4
VCC + 0.5
50
5
740
800
100
100
1300
1800
55
870
mV p-p
V p-p
V p-p
Ω
dB
mV p-p
mV p-p
mV p-p
mV p-p
mV p-p
mV p-p
ADN8102
Parameter
Output Voltage Range
Output Current
Output Resistance
Output Return Loss
LOS CHARACTERISTICS
Assert Level
Deassert Level
POWER SUPPLY
Operating Range
VCC
DVCC
VTTI
VTTO
Supply Current
VTTO
VCC
VEE
LOGIC CHARACTERISTICS
Input High, VIH
Input Low, VIL
Output High, VOH
Output Low, VOL
THERMAL CHARACTERISTICS
Operating Temperature Range
θJA
1
2
Conditions
Single-ended absolute voltage level, TxHeadroom = 0;
VL minimum
Single-ended absolute voltage level, TxHeadroom = 0;
VH maximum
Single-ended absolute voltage level, TxHeadroom = 1;
VL minimum
Single-ended absolute voltage level, TxHeadroom = 1;
VH maximum
Minimum output current per channel
Maximum output current per channel, VCC = 1.8 V
Single-ended
Measured at 2.5 GHz
Min
43
IN_A/IN_B THRESH = 0x0C
IN_A/IN_B HYST = 0x0D
VEE = 0 V
VEE = 0 V, DVCC ≤ (VCC + 1.3 V)
(VEE + 0.4 V + 0.5 × VID) < VTTI < (VCC + 0.5 V)
(VCC − 1.1 V + 0.5 × VOD) < VTTO < (VCC + 0.5 V)
Max
1.7
3.0
VEE + 0.4
VCC − 1.1
V
VCC − 1.2
V
VCC + 0.6
V
2
21
50
5
mA
mA
Ω
dB
57
mV diff
mV diff
1.8
3.3
1.8
1.8
3.6
3.6
3.6
3.6
V
V
V
V
63
460
586
69
565
mA
mA
mA
2.5
1.0
2.5
1.0
−40
+85
22
VICM is the input common-mode voltage.
Programmable via I2C.
Rev. A | Page 4 of 32
Unit
V
VCC + 0.6
20
225
All outputs enabled
All outputs enabled
All outputs enabled
DVCC = 3.3 V
Typ
VCC − 1.1
V
V
V
V
°C
°C/W
ADN8102
TIMING SPECIFICATIONS
Table 2. I2C Timing Parameters
Parameter
fSCL
tHD:STA
tSU:STA
tLOW
tHIGH
tHD:DAT
tSU:DAT
tR
tF
tSU:STO
tBUF
CIO
Min
0
0.6
0.6
1.3
0.6
0
10
1
1
0.6
1
5
Max
400
N/A
N/A
N/A
N/A
N/A
N/A
300
300
N/A
N/A
7
Unit
kHz
μs
μs
μs
μs
μs
ns
ns
ns
μs
ns
pF
Description
SCL clock frequency
Hold time for a start condition
Setup time for a repeated start condition
Low period of the SCL clock
High period of the SCL clock
Data hold time
Data setup time
Rise time for both SDA and SCL
Fall time for both SDA and SCL
Setup time for a stop condition
Bus free time between a stop and a start condition
Capacitance for each I/O pin
SDA
tSU:DAT
tF
tLOW
tR
tHD:STA
tF
tBUF
tR
tHD:STA
S
tHD:DAT
tHIGH
tSU:STA
tSU:STO
Sr
2
Figure 2. I C Timing Diagram
Rev. A | Page 5 of 32
P
S
07060-010
SCL
ADN8102
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
VCC to VEE
VTTI
VTTO
Internal Power Dissipation
Differential Input Voltage
Logic Input Voltage
Storage Temperature Range
Lead Temperature
Rating
3.7 V
VCC + 0.6 V
VCC + 0.6 V
4.26 W
2.0 V
VEE − 0.3 V < VIN < VCC + 0.6 V
−65°C to +125°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating
only; functional operation of the device at these or any other
conditions above those indicated in the operational section of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
ESD CAUTION
Rev. A | Page 6 of 32
ADN8102
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
PE_A1
PE_A0
ENA
OP_A0
ON_A0
VCC
OP_A1
ON_A1
VTTO
OP_A2
ON_A2
VEE
OP_A3
ON_A3
ADDR1
ADDR0
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIN 1
INDICATOR
ADN8102
TOP VIEW
(Not to Scale)
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
SCL
SDA
LOS_B
IP_B0
IN_B0
VCC
IP_B1
IN_B1
VTTI
IP_B2
IN_B2
VEE
IP_B3
IN_B3
EQ_B1
EQ_B0
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Mnemonic
RESET
LOS_A
IN_A0
IP_A0
VCC
IN_A1
IP_A1
VTTI
IN_A2
IP_A2
VEE
IN_A3
IP_A3
DVCC
EQ_A1
EQ_A0
VEE
LB
ON_B0
OP_B0
VCC
ON_B1
OP_B1
VTTO
ON_B2
OP_B2
VEE
Type
Control
Digital I/O
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Power
Control
Control
Power
Control
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Power
Description
Reset Input, Active Low
Port A Loss of Signal Status, Active Low
High Speed Input Complement
High Speed Input
Positive Supply
High Speed Input Complement
High Speed Input
Input Termination Supply
High Speed Input Complement
High Speed Input
Negative Supply
High Speed Input Complement
High Speed Input
Digital Power Supply
Port A Input Equalization MSB
Port A Input Equalization LSB
Negative Supply
Loopback Control
High Speed Output Complement
High Speed Output
Positive Supply
High Speed Output Complement
High Speed Output
Output Termination Supply
High Speed Output Complement
High Speed Output
Negative Supply
Rev. A | Page 7 of 32
07060-002
VEE
LB
ON_B0
OP_B0
VCC
ON_B1
OP_B1
VTTO
ON_B2
OP_B2
VEE
ON_B3
OP_B3
ENB
PE_B1
PE_B0
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RESET
LOS_A
IN_A0
IP_A0
VCC
IN_A1
IP_A1
VTTI
IN_A2
IP_A2
VEE
IN_A3
IP_A3
DVCC
EQ_A1
EQ_A0
ADN8102
Pin No.
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
EP
Mnemonic
ON_B3
OP_B3
ENB
PE_B1
PE_B0
EQ_B0
EQ_B1
IN_B3
IP_B3
VEE
IN_B2
IP_B2
VTTI
IN_B1
IP_B1
VCC
IN_B0
IP_B0
LOS_B
SDA
SCL
ADDR0
ADDR1
ON_A3
OP_A3
VEE
ON_A2
OP_A2
VTTO
ON_A1
OP_A1
VCC
ON_A0
OP_A0
ENA
PE_A0
PE_A1
EPAD
Type
I/O
I/O
Control
Control
Control
Control
Control
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Digital I/O
Control
Control
Control
Control
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Power
I/O
I/O
Control
Control
Control
Power
Description
High Speed Output Complement
High Speed Output
Port B Enable
Port B Output Pre-Emphasis MSB
Port B Output Pre-Emphasis LSB
Port B Input Equalization LSB
Port B Input Equalization MSB
High Speed Input Complement
High Speed Input
Negative Supply
High Speed Input Complement
High Speed Input
Input Termination Supply
High Speed Input Complement
High Speed Input
Positive Supply
High Speed Input Complement
High Speed Input
Port B Loss of Signal Status, Active Low
I2C Control Interface Data Input/Output
I2C Control Interface Clock Input
I2C Control Interface Address LSB
I2C Control Interface Address MSB
High Speed Output Complement
High Speed Output
Negative Supply
High Speed Output Complement
High Speed Output
Output Termination Supply
High Speed Output Complement
High Speed Output
Positive Supply
High Speed Output Complement
High Speed Output
Port A Enable
Port A Output Pre-Emphasis LSB
Port A Output Pre-Emphasis MSB
EPAD Must Be Connected to VEE
Rev. A | Page 8 of 32
ADN8102
TYPICAL PERFORMANCE CHARACTERISTICS
2
50Ω CABLES
2
INPUT
PIN
OUTPUT 2
PIN
50Ω CABLES
2
50Ω
ADN8102
PATTERN
GENERATOR
AC-COUPLED
EVALUATION
BOARD
TP1
TP2
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07060-011
DATA OUT
50ps/DIV
Figure 7. 3.25 Gbps Output Eye, No Channel (TP2 from Figure 4)
50ps/DIV
Figure 6. 3.75 Gbps Input Eye (TP1 from Figure 4)
07060-015
50ps/DIV
07060-013
200mV/DIV
200mV/DIV
Figure 5. 3.25 Gbps Input Eye (TP1 from Figure 4)
07060-014
50ps/DIV
07060-012
200mV/DIV
200mV/DIV
Figure 4. Standard Test Circuit (No Channel)
Figure 8. 3.75 Gbps Output Eye, No Channel (TP2 from Figure 4)
Rev. A | Page 9 of 32
ADN8102
PATTERN
GENERATOR
2
50Ω CABLES
2
FR4 TEST BACKPLANE
50Ω CABLES
2
2
DIFFERENTIAL
STRIPLINE TRACES
TP1
8mils WIDE, 8mils SPACE,
8mils DIELECTRIC HEIGHT
TRACE LENGTHS = 40''
INPUT OUTPUT 2
PIN
PIN
50Ω CABLES
2
50Ω
ADN8102
TP2
AC-COUPLED
EVALUATION
BOARD
TP3
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07060-016
200mV/DIV
DATA OUT
50ps/DIV
REFERENCE EYE DIAGRAM AT TP1
50ps/DIV
Figure 12. 3.25 Gbps Output Eye, 40 Inch FR4 Input Channel, Best EQ Setting
(TP3 from Figure 9)
50ps/DIV
Figure 11. 3.75 Gbps Input Eye, 40 Inch FR4 Input Channel (TP2 from Figure 9)
07060-020
50ps/DIV
07060-018
200mV/DIV
200mV/DIV
Figure 10. 3.25 Gbps Input Eye, 40 Inch FR4 Input Channel (TP2 from Figure 9)
07060-019
50ps/DIV
07060-017
200mV/DIV
200mV/DIV
Figure 9. Input Equalization Test Circuit, FR4
Figure 13. 3.75 Gbps Output Eye, 40 Inch FR4 Input Channel, Best EQ Setting
(TP3 from Figure 9)
Rev. A | Page 10 of 32
ADN8102
PATTERN
GENERATOR
2
50Ω CABLES
2
30m CX4 CABLE
50Ω CABLES
2
2
INPUT OUTPUT 2
PIN
PIN
50Ω CABLES
2
50Ω
ADN8102
TP1
TP2
AC-COUPLED
EVALUATION
BOARD
TP3
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07060-021
200mV/DIV
DATA OUT
50ps/DIV
REFERENCE EYE DIAGRAM AT TP1
50ps/DIV
Figure 17. 3.25 Gbps Output Eye, 30 Meters CX4 Cable, Best EQ Setting
(TP3 from Figure 14)
50ps/DIV
Figure 16. 3.75 Gbps Input Eye, 30 Meters CX4 Cable (TP2 from Figure 14)
07060-025
50ps/DIV
07060-023
200mV/DIV
200mV/DIV
Figure 15. 3.25 Gbps Input Eye, 30 Meters CX4 Cable (TP2 from Figure 14)
07060-024
50ps/DIV
07060-022
200mV/DIV
200mV/DIV
Figure 14. Input Equalization Test Circuit, CX4
Figure 18. 3.75 Gbps Output Eye, 30 Meters CX4 Cable, Best EQ Setting
(TP3 from Figure 14)
Rev. A | Page 11 of 32
ADN8102
PATTERN
GENERATOR
2
50Ω CABLES
2
50Ω CABLES
2
INPUT OUTPUT 2
PIN
PIN
ADN8102
TP1
FR4 TEST BACKPLANE
2
50Ω CABLES
2
50Ω
DIFFERENTIAL
STRIPLINE TRACES
TP2
8mils WIDE, 8mils SPACE,
8mils DIELECTRIC HEIGHT
TRACE LENGTHS = 40''
AC-COUPLED
EVALUATION
BOARD
TP3
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07060-026
200mV/DIV
DATA OUT
50ps/DIV
REFERENCE EYE DIAGRAM AT TP1
50ps/DIV
Figure 22. 3.25 Gbps Output Eye, 40 Inch FR4 Output Channel,
PE = Best Setting (TP3 from Figure 19)
50ps/DIV
Figure 21. 3.75 Gbps Output Eye, 40 Inch FR4 Output Channel,
PE = 0 (TP3 from Figure 19)
Figure 23. 3.75 Gbps Output Eye, 40 Inch FR4 Output Channel,
PE = Best Setting (TP3 from Figure 19)
Rev. A | Page 12 of 32
07060-030
50ps/DIV
07060-028
200mV/DIV
200mV/DIV
Figure 20. 3.25 Gbps Output Eye, 40 Inch FR4 Output Channel,
PE = 0 (TP3 from Figure 19)
07060-029
50ps/DIV
07060-027
200mV/DIV
200mV/DIV
Figure 19. Output Pre-Emphasis Test Circuit, FR4
ADN8102
200mV/DIV
DATA OUT
2
50Ω CABLES
2
INPUT OUTPUT 2
PIN
PIN
50Ω CABLES
2
15m CX4 CABLE
2
50Ω CABLES
2
50Ω
ADN8102
PATTERN
GENERATOR
AC-COUPLED
EVALUATION
BOARD
TP3
TP2
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07060-031
TP1
50ps/DIV
REFERENCE EYE DIAGRAM AT TP1
50ps/DIV
Figure 27. 3.25 Gbps Output Eye, 15 Meters CX4 Cable,
PE = Best Setting (TP3 from Figure 24)
50ps/DIV
Figure 26. 3.75 Gbps Output Eye, 15 Meters CX4 Cable,
PE = 0 (TP3 from Figure 24)
Figure 28. 3.75 Gbps Output Eye, 15 Meters CX4 Cable,
PE = Best Setting (TP3 from Figure 24)
Rev. A | Page 13 of 32
07060-035
50ps/DIV
07060-033
50mV/DIV
50mV/DIV
Figure 25. 3.25 Gbps Output Eye, 15 Meters CX4 Cable,
PE = 0 (TP3 from Figure 24)
07060-034
50ps/DIV
07060-032
50mV/DIV
50mV/DIV
Figure 24. Output Pre-Emphasis Test Circuit, CX4
ADN8102
100
80
DETERMINISTIC JITTER (ps)
DETERMINISTIC JITTER (ps)
70
60
50
40
30
20
80
60
VCC = 3.3V
40
VCC = 1.8V
20
0
20
60
40
DATA RATE (Hz)
0
1.0
07060-036
0
Figure 29. Deterministic Jitter vs. Data Rate
1.5
2.0
2.5
3.0
INPUT COMMON MODE (V)
3.5
4.0
07060-039
10
Figure 32. Deterministic Jitter vs. Input Common Mode
100
100
80
DETERMINISTIC JITTER (ps)
DETERMINISTIC JITTER (ps)
90
70
60
50
40
30
20
80
60
40
20
0.5
1.0
1.5
2.0
DIFFERENTIAL INPUT SWING (V)
2.5
0
1.0
100
80
80
DETERMINISTIC JITTER (ps)
100
60
40
20
0
–60
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
100
2.0
2.5
VCC (V)
3.0
3.5
4.0
Figure 33. Deterministic Jitter vs. Supply Voltage
60
VCC = 1.8V
40
VCC = 3.3V
20
0
1.0
07060-038
DETERMINISTIC JITTER (ps)
Figure 30. Deterministic Jitter vs. Differential Input Swing
1.5
Figure 31. Deterministic Jitter vs. Temperature
1.5
2.0
2.5
VTTO (V)
3.0
3.5
4.0
Figure 34. Deterministic Jitter vs. Output Termination Voltage
Rev. A | Page 14 of 32
07060-041
0
07060-037
0
07060-040
10
ADN8102
450000
100
400000
90
300000
tR/tF (ps)
250000
200000
80
tR/tF
70
150000
100000
60
0
–8
–6
–4
–2
0
2
JITTER (ps)
4
6
8
10
Figure 35. Random Jitter Histogram
50
–60
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 36. Rise Time (tR)/Fall Time (tF) vs. Temperature
Rev. A | Page 15 of 32
100
07060-043
50000
07060-042
NUMBER OF SAMPLES
350000
ADN8102
THEORY OF OPERATION
LOS_B
TRANSMIT
PRE-EMPHASIS
EQ
2:1
PE
The ADN8102 receiver inputs incorporate 50 Ω termination
resistors, ESD protection, and a multizero transfer function
equalizer that can be optimized for backplane or cable operation.
Each channel also provides a programmable loss-of-signal (LOS)
function that provides an interrupt that can be used to squelch
or disable the associated output when the differential input voltage
falls below the programmed threshold value. Each receive channel
also provides a P/N inversion function that allows the user to
swap the sign of the input signal path to eliminate the need for
board-level crossovers in the receiver channel.
Ox_B[3:0]
LOS_A
LB
RECEIVE
EQUALIZATION
TRANSMIT
PRE-EMPHASIS
Ox_A[3:0]
Input Structure and Input Levels
PE
ADDR[1:0]
SCL
SDA
RESET
2:1
EQ
CONTROL LOGIC
Ix_A[3:0]
EQ_A[1:0]
PE_A[1:0]
EQ_B[1:0]
PE_B[1:0]
ENA
ENB
07060-003
Ix_B[3:0]
RECEIVERS
ADN8102
RECEIVE
EQUALIZATION
Table 5 illustrates some, but not all, possible combinations of
input supply voltages.
Figure 37. Simplified Functional Block Diagram
Table 5. Common Input Voltage Levels
The ADN8102 is a quad bidirectional cable and backplane
equalizer that provides both input equalization and output preemphasis on both the line card and cable sides of the device.
The device supports full loopback and through connectivity
of the two unidirectional half-links, each consisting of four
differential signal pairs.
Configuration
Low VTTI, AC-Coupled Input
Single 1.8 V Supply
3.3 V Core
Single 3.3 V Supply
VCC
The ADN8102 offers extensively programmable output levels
and pre-emphasis as well as the ability to disable the output
current. The receivers integrate a programmable, multizero
equalizer transfer function that is optimized to compensate
either typical backplane or typical cable losses.
The I/O on-chip termination resistors are terminated to usersettable supplies to support dc coupling in a wide range of logic
styles. The ADN8102 supports a wide core supply range; VCC
can be set from 1.8 V to 3.3 V. These features, together with
programmable output levels, allow for a wide range of dc- and
ac-coupled I/O configurations.
VCC (V)
1.8
1.8
3.3
3.3
VTTI (V)
1.6
1.8
1.8
3.3
SIMPLIFIED RECEIVER INPUT CIRCUIT
VTTI
RLN
RP
52Ω
IP
RN
52Ω
R1
750Ω
RLP
Q1
R3
1kΩ
IN
Q2
R2
750Ω
I1
07060-004
INTRODUCTION
VEE
Rev. A | Page 16 of 32
Figure 38. Simplified Input Structure
ADN8102
EQUALIZATION SETTINGS
The ADN8102 receiver incorporates a multizero transfer function
continuous time equalizer that provides up to 22 dB of high
frequency boost at 1.875 GHz to compensate up to 30 meters
of CX4 cable or 40 inches of FR4 at 3.75 Gbps. The ADN8102
allows joint control of the equalizer transfer function of the
four equalizer channels in a single port through the I2C control
interface. Port A and Port B equalizer transfer functions are
controlled via Register 0x80 and Register 0xA0, respectively.
The equalizer transfer function allows independent control of
the boost in two different frequency ranges for optimal matching
with the loss shape of the user’s channel (for example, skin-effect
loss dominated or dielectric loss dominated). By default, the
equalizer control is simplified to two independent maps of basic
settings that provide nine settings, each optimized for CX4 cable
and FR4 to ease programming for typical channels. The default
state of the part selects the CX4 optimized equalization map for
the IN_A[3:0] channels that interface with the cable and the FR4
optimized equalization map for the IN_B[3:0] channels that
interface with the board. Full control of the equalizer is available via
the I2C control interface by writing register bit MODE[0] = 1 at
Address 0x0F. Table 6 summarizes the high frequency boost for
each of the basic control settings and the typical length of CX4
cable and FR4 trace that each setting compensates. Setting the
EQBY bit of the IN_A/IN_B configuration registers high sets
the equalization to 1.5 dB of boost, which compensates 0 meters
to 2 meters of CX4 or 0 inches to 10 inches of FR4.
Setting the LUT SELECT bit = 1 (Bit 1 in the IN_Ax/IN_Bx FR4
control registers) allows the default map selection (CX4 or FR4
optimized) to be overwritten via the LUT FR4/CX4 bit (Bit 0)
in the IN_Ax/IN_Bx FR4 control registers. Setting this bit high
selects the FR4 optimized map, and setting it low selects the CX4
optimized map. These settings are set on a per channel basis
(see Table 7 and Table 17).
The user can also specify the boost in the mid frequency and high
frequency ranges independently. This is done by writing to the
IN_A/IN_B EQ1 control and IN_A/IN_B EQ2 control registers for
the channel of interest. Each of these registers provides 32 settings
of boost, with IN_A/IN_B EQ1 control setting the mid-frequency
boost and IN_A/IN_B EQ2 control setting the high frequency
boost. The IN_A/IN_B EQx control registers are ordered such
that Bit 5 is a sign bit, and midlevel boost is centered on 0x00;
setting Bit 5 low and increasing the LSBs results in decreasing
boost, while setting Bit 5 high and increasing the LSBs results in
increasing boost. The EQ CTL SRC bit (Bit 6) in the IN_A/IN_B
EQ1 Control registers determines whether the equalization
control for the channel of interest is selected from the optimized
map or directly from the IN_A/IN_B EQx control registers (per
port). Setting this bit high selects equalization control directly
from the IN_A/IN_B EQx control registers, and setting it low
selects equalization control from the selected optimized map.
Table 6. Receive Equalizer Boost vs. Setting (CX4 and FR4 Optimized Maps)
IN_Ax/IN_Bx
Configuration, EQ[2:0]
01
1
21
3
4
51
6
71
1
Boost (dB)
10
12
14
17
19
20
21
22
Cable Optimized
Typical CX4 Cable Length (Meters)
4 to 6
8 to 10
12 to 14
16 to 18
20 to 22
24 to 26
28 to 30
30 to 32
Boost (dB)
3.5
3.9
4.25
4.5
4.75
5.0
5.3
5.5
FR4 Optimized
Typical FR4 Trace Length (Inches)
5 to 10
10 to 15
15 to 20
20 to 25
25 to 30
30 to 35
35 to 40
35 to 40
These EQ settings are also available via the external device pins, EQ_A[1:0] and EQ_B[1:0].
Table 7. Receive Configuration and Equalization Registers
Name
IN_A/IN_B
Configuration
IN_A/IN_B
EQ1 Control
IN_A/IN_B
EQ2 Control
IN_Ax/IN_Bx
FR4 Control
Address
0x80, 0xA0
0x83, 0xA3
0x84, 0xA4
Bit 7
Bit 6
PNSWAP
Bit 5
EQBY
Bit 4
EN
Bit 3
Bit 2
EQ[2]
Bit 1
EQ[1]
Bit 0
EQ[0]
Default
0x30
EQ CTL SRC
EQ1[5]
EQ1[4]
EQ1[3]
EQ1[2]
EQ1[1]
EQ1[0]
0x00
EQ2[5]
EQ2[4]
EQ2[3]
EQ2[2]
EQ2[1]
EQ2[0]
0x00
LUT SELECT
LUT FR4/CX4
0x00
0x85, 0x8D, 0x95,
0x9D, 0xA5, 0xAD,
0xB5, 0xBD
Rev. A | Page 17 of 32
ADN8102
Loss of Signal/Signal Detect
Recommended LOS Settings
An independent signal detect output is provided for all eight
input ports of the device. The signal-detect function measures
the low frequency amplitude of the signal at the receiver input
and compares this measurement with a defined threshold level.
If the measurement indicates that the input signal swing is
smaller than the threshold for 250 μs, the channel indicates a
loss-of-signal event. Assertion and deassertion of the LOS signal
occurs within 100 μs of the event.
Recommended settings for LOS are as follows:
The LOS-assert and LOS-deassert levels are set on a per channel
basis through the I2C control interface, by writing to the IN_A/
IN_B LOS threshold and IN_A/IN_B LOS hysteresis registers,
respectively. The recommended settings are IN_A/IN_B THRESH
= 0x0C and IN_A/IN_B HYST = 0x0D. All ports are factory
tested with these settings to ensure that an LOS event is asserted
for single-ended dc input swings less than 20 mV and is deasserted
for single-ended dc input swings greater than 225 mV.
The LOS status for each individual channel can be accessed
through the I2C control interface. The independent channel
LOS status can be read from the IN_A/IN_B LOS status registers
(Address 0x1F and Address 0x3F). The four LSBs of each register
represent the current LOS status of each channel, with high
representing an ongoing LOS event. The four MSBs of each
register represent the historical LOS status of each channel,
with high representing a LOS event at any time on a specific
channel. The MSBs are sticky and remain high once asserted
until cleared by the user by overwriting the bits to 0.
•
Set IN_A/IN_B THRESH to 0x0C for an assert voltage of
20 mV differential (40 mV p-p differential).
•
Set IN_A/IN_B HYST to 0x0D for a deassert voltage of
225 mV differential (450 mV p-p differential).
LANE INVERSION
The input P/N inversion is a feature intended to allow the user
to implement the equivalent of a board-level crossover in a much
smaller area and without additional via impedance discontinuities
that degrade the high frequency integrity of the signal path. The
P/N inversion is available on a per port basis and is controlled
through the I2C control interface. The P/N inversion is accomplished by writing to the PNSWAP bit (Bit 6) of the IN_A/IN_B
configuration register (see Table 7) with low representing a
noninverting configuration and high representing an inverting
configuration. Note that using this feature to account for signal
inversions downstream of the receiver requires additional attention
when switching connectivity.
Table 8. LOS Threshold and Hysteresis Control Registers
Name
IN_A/IN_B
LOS Threshold
IN_A/IN_B
LOS Hysteresis
Address
0x81,
0xA1
0x82,
0xA2
Bit 7
Bit 6
THRESH[6]
Bit 5
THRESH[5]
Bit 4
THRESH[4]
Bit 3
THRESH[3]
Bit 2
THRESH[2]
Bit 1
THRESH[1]
Bit 0
THRESH[0]
Default
0x04
HYST[6]
HYST[5]
HYST[4]
HYST[3]
HYST[2]
HYST[1]
HYST[0]
0x12
Table 9. LOS Status Registers
Name
IN_A/IN_B
LOS Status
Address
0x1F,
0x3F
Bit 7
STICKY
LOS[3]
Bit 6
STICKY
LOS[2]
Bit 5
STICKY
LOS[1]
Bit 4
STICKY LOS [0]
Rev. A | Page 18 of 32
Bit 3
REAL-TIME
LOS[3]
Bit 2
REAL-TIME
LOS[2]
Bit 1
REAL-TIME
LOS[1]
Bit 0
REAL-TIME
LOS[0]
ADN8102
Bit 1 represents loopback of the Port A inputs to the Port B
outputs (cable side loopback). Bit 0 represents loopback of the
Port B inputs to the Port A outputs (board side loopback), with
high representing loopback for both bits. Bit 0 is also controlled
through the LB pin with I2C data overwriting the pin state. Both
input ports can be looped back simultaneously (full loopback)
by writing high to both Bit 0 and Bit 1, but in this case, valid
data is disrupted on each channel. Figure 39 illustrates the three
loopback modes.
The ADN8102 provides loopback on both input ports (Port A:
cable interface input, Port B: line card interface input). The external
loopback toggle pin, LB, controls the loopback of the Port B input
only (board side loopback). When loopback is asserted, valid
data continues to pass through the Port B link, but the Port B
input signals are also shunted to the Port A output to allow testing
and debugging without disrupting valid data. This loopback, as
well as loopback of the Port A input (cable side loopback), can
be programmed through the I2C interface. The loopbacks are
controlled through the I2C interface by writing to Bit 0 and
Bit 1 of the global configuration control register (Register 0x02).
CABLE SIDE LOOPBACK
RECEIVE
EQUALIZATION
Ix_B[3:0]
PE
EQ
ADDR[1:0]
SCL
SDA
RESET
Ox_B[3:0]
Ix_B[3:0]
LOS_A
LB
Ox_A[3:0]
BOARD SIDE LOOPBACK
RECEIVE
EQUALIZATION
TRANSMIT
PRE-EMPHASIS
TRANSMIT
PRE-EMPHASIS
RECEIVE
EQUALIZATION
PE
EQ
CONTROL LOGIC
FULL LOOPBACK
TRANSMIT
PRE-EMPHASIS
Ox_B[3:0]
PE
EQ
LOS_A
LB
Ix_A[3:0]
Ox_A[3:0]
EQ_A[1:0]
PE_A[1:0]
EQ_B[1:0]
PE_B[1:0]
ENA
ENB
ADDR[1:0]
SCL
SDA
RESET
RECEIVE
EQUALIZATION
TRANSMIT
PRE-EMPHASIS
RECEIVE
EQUALIZATION
PE
EQ
CONTROL LOGIC
Ix_B[3:0]
TRANSMIT
PRE-EMPHASIS
Ox_B[3:0]
PE
EQ
LOS_A
LB
Ix_A[3:0]
Ox_A[3:0]
EQ_A[1:0]
PE_A[1:0]
EQ_B[1:0]
PE_B[1:0]
ENA
ENB
ADDR[1:0]
SCL
SDA
RESET
TRANSMIT
PRE-EMPHASIS
RECEIVE
EQUALIZATION
PE
EQ
CONTROL LOGIC
Ix_A[3:0]
EQ_A[1:0]
PE_A[1:0]
EQ_B[1:0]
PE_B[1:0]
ENA
ENB
Figure 39. Loopback Modes of Operation
Table 10. Global Configuration Register, Loopback Controls
Name
Global Configuration Control
Address
0x02
Bit 7
Bit 6
Bit 5
Rev. A | Page 19 of 32
Bit 4
Bit 3
Bit 2
Bit 1
LB[1]
Bit 0
LB[0]
Default
0x00
07060-005
LOOPBACK
ADN8102
The output equalization is optimized for less than 1.75 Gbps
operation but can be optimized for higher speed applications at
up to 3.75 Gbps through the I2C control interface by writing to
the DATA RATE bit (Bit 4) of the OUT_A/OUT_B configuration
registers, with high representing 3.75 Gbps and low representing
1.75 Gbps. The PE CTL SRC bit (Bit 7) in the OUT_A/OUT_B
Output Level Control 1 register determines whether the preemphasis and output current controls for the channel of interest
are selected from the optimized map or directly from the OUT_A/
OUT_B Output Level Control[1:0] registers (per channel). Setting
this bit high selects pre-emphasis control directly from the
OUT_A/OUT_B Output Level Control[1:0] registers, and setting
it low selects pre-emphasis control from the optimized map.
TRANSMITTERS
Output Structure and Output Levels
The ADN8102 transmitter outputs incorporate 50 Ω termination resistors, ESD protection, and an output current switch. Each
port provides control of both the absolute output level and the
pre-emphasis output level. It should be noted that the choice of
output level affects the output common-mode level. A 600 mV
peak-to-peak differential output level with full pre-emphasis
range requires an output termination voltage of 2.5 V or greater
(VTTO, VCC ≥ 2.5 V).
Pre-Emphasis
The total output amplitude and pre-emphasis setting space is
reduced to a single map of basic settings that provides seven
settings of output equalization to ease programming for typical
channels. The PE_A/PE_B[1:0] pins provide selections 0, 2, 4,
and 6 of the seven pre-emphasis settings through toggle pin
control, covering the entire range of settings at lower resolution.
The full resolution of seven settings is available through the I2C
interface by writing to Bits[2:0] (PE[2:0] of the OUT_A/OUT_B
configuration registers) with I2C settings overriding the toggle
pin control. Similar to the receiver settings, the ADN8102 allows
joint control of all four channels in a transmit port. Table 11
summarizes the absolute output level, pre-emphasis level, and
high frequency boost for each of the basic control settings and
the typical length of the CX4 cable and FR4 trace that each
setting compensates.
Tx SIMPLIFIED DIAGRAM
VCC
ON-CHIP
TERMINATION
V3
VC
V2
VP
RP
50Ω
ESD
VTTO
RN
50Ω
OP
V1
VN
ON
Q1
IDC + IPE
ITOT
VEE
07060-006
Q2
Figure 40. Simplified Output Structure
Full control of the transmit output levels is available through the
I2C control interface. This full control is achieved by writing to
the OUT_A/OUT_B Output Level Control[1:0] registers for the
channel of interest. Table 13 shows the supported output level
settings of the OUT_A/OUT_B Output Level Control[1:0]
registers. Register settings not listed in Table 13 are not
supported by the ADN8102.
Table 11. Transmit Pre-Emphasis Boost and Overshoot vs. Setting
PE
01
1
21
3
41
5
61
1
Boost (dB)
0
2
3.5
4.9
6
7.4
9.5
Overshoot
0%
25%
50%
75%
100%
133%
200%
DC Swing (mV p-p diff)
800
800
800
800
800
600
400
Typical CX4 Cable Length (Meters)
0 to 2.5
2.5 to 5
5 to 7.5
7.5 to 10
10 to 12.5
15 to 17.5
20 to 22.5
Typical FR4 Trace Length (Inches)
0 to 5
0 to 5
10 to 15
10 to 15
15 to 20
20 to 25
25 to 30
These PE settings are also available via external device pins, PE_A[1:0] and PE_B[1:0].
Table 12. Output Configuration Registers
Name
OUT_A/OUT_B Configuration
OUT_A/OUT_B Output Level Control 1
OUT_A/OUT_B Output Level Control 0
Address
0xC0, 0xE0
0xC1, 0xE1
0xC2, 0xE2
Bit 7
Bit 6
Bit 5
EN
PE CTL SRC
Rev. A | Page 20 of 32
Bit 4
Bit 3 Bit 2
DATA RATE
PE[2]
OUTx_OLEV1[6:0]
OUTx_OLEV0[6:0]
Bit 1
PE[1]
Bit 0
PE[0]
Default
0x20
0x40
0x40
ADN8102
Table 13. Output Level Settings
VOD (mV)
50
50
50
50
50
50
50
100
100
100
100
100
100
100
150
150
150
150
150
150
150
200
200
200
200
200
200
200
250
250
250
250
250
250
250
300
300
300
300
300
300
300
350
350
350
350
350
350
350
400
400
400
400
400
400
400
VD Peak (mV)
50
150
250
350
450
550
650
100
200
300
400
500
600
700
150
250
350
450
550
650
750
200
300
400
500
600
700
800
250
350
450
550
650
750
850
300
400
500
600
700
800
900
350
450
550
650
750
850
950
400
500
600
700
800
900
1000
PE (dB)
0.00
9.54
13.98
16.90
19.08
20.83
22.28
0.00
6.02
9.54
12.04
13.98
15.56
16.90
0.00
4.44
7.36
9.54
11.29
12.74
13.98
0.00
3.52
6.02
7.96
9.54
10.88
12.04
0.00
2.92
5.11
6.85
8.30
9.54
10.63
0.00
2.50
4.44
6.02
7.36
8.52
9.54
0.00
2.18
3.93
5.38
6.62
7.71
8.67
0.00
1.94
3.52
4.86
6.02
7.04
7.96
ITOT (mA)
2
6
10
14
18
22
26
4
8
12
16
20
24
28
6
10
14
18
22
26
30
8
12
16
20
24
28
32
10
14
18
22
26
30
34
12
16
20
24
28
32
36
14
18
22
26
30
34
38
16
20
24
28
32
36
40
OUT_A/OUT_B Output Level Control 0
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
Rev. A | Page 21 of 32
OUT_A/OUT_B Output Level Control 1
0x81
0x81
0x81
0x81
0x81
0x81
0x81
0x91
0x91
0x91
0x91
0x91
0x91
0x91
0x92
0x92
0x92
0x92
0x92
0x92
0x92
0xA2
0xA2
0xA2
0xA2
0xA2
0xA2
0xA2
0xA3
0xA3
0xA3
0xA3
0xA3
0xA3
0xA3
0xB3
0xB3
0xB3
0xB3
0xB3
0xB3
0xB3
0xB4
0xB4
0xB4
0xB4
0xB4
0xB4
0xB4
0xC4
0xC4
0xC4
0xC4
0xC4
0xC4
0xC4
ADN8102
VOD (mV)
450
450
450
450
450
450
450
500
500
500
500
500
500
500
550
550
550
550
550
550
550
600
600
600
600
600
600
600
650
650
650
650
650
650
700
700
700
700
700
750
750
750
750
800
800
800
850
850
900
VD Peak (mV)
450
550
650
750
850
950
1050
500
600
700
800
900
1000
1100
550
650
750
850
950
1050
1150
600
700
800
900
1000
1100
1200
650
750
850
950
1050
1150
700
800
900
1000
1100
750
850
950
1050
800
900
1000
850
950
900
PE (dB)
0.00
1.74
3.19
4.44
5.52
6.49
7.36
0.00
1.58
2.92
4.08
5.11
6.02
6.85
0.00
1.45
2.69
3.78
4.75
5.62
6.41
0.00
1.34
2.50
3.52
4.44
5.26
6.02
0.00
1.24
2.33
3.30
4.17
4.96
0.00
1.16
2.18
3.10
3.93
0.00
1.09
2.05
2.92
0.00
1.02
1.94
0.00
0.97
0.00
ITOT (mA)
18
22
26
30
34
38
42
20
24
28
32
36
40
44
22
26
30
34
38
42
46
24
28
32
36
40
44
48
26
30
34
38
42
46
28
32
36
40
44
30
34
38
42
32
36
40
34
38
36
OUT_A/OUT_B Output Level Control 0
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x01
0x12
0x23
0x34
0x45
0x56
0x02
0x13
0x24
0x35
0x46
0x03
0x14
0x25
0x36
0x04
0x15
0x26
0x05
0x16
0x06
Rev. A | Page 22 of 32
OUT_A/OUT_B Output Level Control 1
0xC5
0xC5
0xC5
0xC5
0xC5
0xC5
0xC5
0xD5
0xD5
0xD5
0xD5
0xD5
0xD5
0xD5
0xD6
0xD6
0xD6
0xD6
0xD6
0xD6
0xD6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
ADN8102
High Current Setting and Output Level Shift
In low voltage applications, users must pay careful attention to
both the differential and common-mode signal levels (see Figure 41
and Table 14 and Table 15. Failure to understand the implications
of signal level and choice of ac or dc coupling almost certainly leads
to transistor saturation and poor transmitter performance.
VTTO
ΔVOCM
VH
VOD
VOCM
TxHeadroom
Rev. A | Page 23 of 32
VL
VOD p-p = 2 × VOD
VEE
Figure 41. Simplified Output Voltage Levels Diagram
07060-007
The TxHeadroom register (Register 0x23) allows configuration
of the individual transmitters for extra headroom at the output
for high current applications. The bits in this register are active
high (default) and are one per output (see Table 17). Setting a
bit high puts the respective transmitter in a configuration for
extra headroom and setting a bit low does not provide extra
headroom. The TxHeadroom bits should only be set high when
VCC exceeds the value listed in Table 14 for a given output swing.
ADN8102
Signal Levels and Common-Mode Shift for DC- and AC-Coupled Outputs
Table 14.
Output Levels and Output Compliance
AC-Coupled Transmitter
DC-Coupled Transmitter
VL
VL
Min
VD
VH
VH
PE
dVOCM VH
Peak Peak dVOCM VH
Peak Peak VL
VOD ITOT Peak PE
VL
VL
(V)
(V)
(mV) (mA) (mV) Boost (dB) (mV) (V) (V) (V)
(mV) (V) (V) (V)
(V)
VTTO and VCC = 3.3 V
200 8
200 1.00
200 12
300 1.50
200 16
400 2.00
200 20
500 2.50
200 24
600 3.00
200 28
700 3.50
200 32
800 4.00
300 12
300 1.00
300 16
400 1.33
300 20
500 1.67
300 24
600 2.00
300 28
700 2.33
300 32
800 2.67
300 36
900 3.00
400 16
400 1.00
400 20
500 1.25
400 24
600 1.50
400 28
700 1.75
400 32
800 2.00
400 36
900 2.25
400 40
1000 2.50
600 24
600 1.00
600 28
700 1.17
600 32
800 1.33
600 36
900 1.50
600 40
1000 1.67
600 44
1200 1.83
600 48
1400 2.00
VTTO and VCC = 1.8 V 1
200 8
200 1.00
200 12
300 1.50
200 16
400 2.00
200 20
500 2.50
200 24
600 3.00
300 12
300 1.00
300 16
400 1.33
300 20
500 1.67
300 24
600 2.00
300 28
700 2.33
400 16
400 1.00
400 20
500 1.25
400 24
600 1.50
400 28
700 1.75
400 32
800 2.00
600 24
600 1.00
1
TxHeadroom = 0
Max
Min
Min
VCC − VL VCC
VL
(V)
(V)
(V)
TxHeadroom = 1
Max
VCC − VL Min
(V)
VCC (V)
0.00
3.52
6.02
7.96
9.54
10.88
12.04
0.00
2.50
4.44
6.02
7.36
8.52
9.54
0.00
1.94
3.52
4.86
6.02
7.04
7.96
0.00
1.34
2.50
3.52
4.44
5.26
6.02
200
300
400
500
600
700
800
300
400
500
600
700
800
900
400
500
600
700
800
900
1000
600
700
800
900
1000
1100
1200
3.2
3.1
3
2.9
2.8
2.7
2.6
3.15
3.05
2.95
2.85
2.75
2.65
2.55
3.1
3
2.9
2.8
2.7
2.6
2.5
3
2.9
2.8
2.7
2.6
2.5
2.4
3
2.9
2.8
2.7
2.6
2.5
2.4
2.85
2.75
2.65
2.55
2.45
2.35
2.25
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2.4
2.3
2.2
2.1
2
1.9
1.8
3.2
3.15
3.1
3.05
3
2.95
2.9
3.15
3.1
3.05
3
2.95
2.9
2.85
3.1
3.05
3
2.95
2.9
2.85
2.8
3
2.95
2.9
2.85
2.8
2.75
2.7
3
2.85
2.7
2.55
2.4
2.25
2.1
2.85
2.7
2.55
2.4
2.25
2.1
1.95
2.7
2.55
2.4
2.25
2.1
1.95
1.8
2.4
2.25
2.1
1.95
1.8
1.65
1.5
100
150
200
250
300
350
400
150
200
250
300
350
400
450
200
250
300
350
400
450
500
300
350
400
450
500
550
600
3.3
3.25
3.2
3.15
3.1
3.05
3
3.3
3.25
3.2
3.15
3.1
3.05
3
3.3
3.25
3.2
3.15
3.1
3.05
3
3.3
3.25
3.2
3.15
3.1
3.05
3
3.1
3.05
3
2.95
2.9
2.85
2.8
3
2.95
2.9
2.85
2.8
2.75
2.7
2.9
2.85
2.8
2.75
2.7
2.65
2.6
2.7
2.65
2.6
2.55
2.5
2.45
2.4
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.1
3
2.9
2.8
2.7
2.6
2.5
3
2.9
2.8
2.7
2.6
2.5
2.4
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.1
2.225
2.225
2.225
2.225
2.1
2.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
2
2
2
2
2
2.2
2.2
2
2
2
2
2
2.2
2.2
2
2
2
2
2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
0.00
3.52
6.02
7.96
9.54
0.00
2.50
4.44
6.02
7.36
0.00
1.94
3.52
4.86
6.02
0.00
200
300
400
500
600
300
400
500
600
700
400
500
600
700
800
600
1.7
1.6
1.5
1.4
1.3
1.65
1.55
1.45
1.35
1.25
1.6
1.5
1.4
1.3
1.2
1.5
1.5
1.4
1.3
1.2
1.1
1.35
1.25
1.15
1.05
0.95
1.2
1.1
1
0.9
0.8
0.9
1.7
1.65
1.6
1.55
1.5
1.65
1.6
1.55
1.5
1.45
1.6
1.55
1.5
1.45
1.4
1.5
1.5
1.35
1.2
1.05
0.9
1.35
1.2
1.05
0.9
0.75
1.2
1.05
0.9
0.75
0.6
0.9
100
150
200
250
300
150
200
250
300
350
200
250
300
350
400
300
1.8
1.75
1.7
1.65
1.6
1.8
1.75
1.7
1.65
1.6
1.8
1.75
1.7
1.65
1.6
1.8
1.6
1.55
1.5
1.45
1.4
1.5
1.45
1.4
1.35
1.3
1.4
1.35
1.3
1.25
1.2
1.2
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.6
1.5
1.4
1.3
1.2
1.5
1.4
1.3
1.2
1.1
1.4
1.3
1.2
1.1
1
1.2
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.6
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.9
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
TxHeadroom = 1 is not an option at VTTO and VCC = 1.8 V.
Rev. A | Page 24 of 32
ADN8102
Table 15. Symbol Definitions for Output Levels vs. Setting
Symbol
VOD
VOD p-p
dVOCM_DC-COUPLED
dVOCM_AC-COUPLED
IDC
IPE
ITOT
VH
VL
Formula
25 Ω × IDC
25 Ω × IDC × 2 = 2 × VOD
25 Ω × ITOT/2 = VOD p-p/4 + (IPE/2 × 25)
50 Ω × ITOT/2 = VOD p-p/2 + (IPE/2 × 50)
VOD/RTERM
—
IDC + IPE
VTTO − dVOCM + VOD/2
VTTO − dVOCM − VOD/2
Definition
Peak differential output voltage
Peak-to-peak differential output voltage
Output common-mode shift
Output common-mode shift
Output current that sets output level
Output current used for PE
Total transmitter output current
Maximum single-ended output voltage
Minimum single-ended output voltage
SELECTIVE SQUELCH AND DISABLE
Table 16. Squelch Programming
Each transmitter is equipped with output disable and output
squelch controls. Disable is a full power-down state: the transmitter current is reduced to zero and the output pins pull up
to VTTO, but there is a delay of approximately 1 μs associated
with re-enabling the transmitter. The output disable control is
accessed through the EN bit (Bit 5) of the OUT_A/OUT_B
configuration registers through the I2C control interface.
Name
OUT_A/
OUT_B
Squelch
Control
Squelch is not a full power-down state but a state in which only
the output current is reduced to zero and the output pins pull
up to VTTO, and there is a much smaller delay to bring back
the output current. The output squelch and the output disable
control can both be accessed through the OUT_A/OUT_B
squelch control registers, with the top nibble representing the
squelch control for one entire output port and the bottom
nibble representing the output disable for one entire output
port. The ports are disabled or squelched by writing 0s to the
corresponding nibbles. The ports are enabled by writing all 1s,
which is the default setting. For example, to squelch Port A,
Register 0xC3 must be set to 0x0F. The entire nibble must be
written to all 0s for this functionality.
Rev. A | Page 25 of 32
Address
0xC3,
0xE3
Data
SQUELCH[3:0]
DISABLE[3:0]
Default
0xFF
ADN8102
I2C CONTROL INTERFACE
7.
SERIAL INTERFACE GENERAL FUNCTIONALITY
The ADN8102 register set is controlled through a 2-wire
I2C interface. The ADN8102 acts only as an I2C slave device.
Therefore, the I2C bus in the system needs to include an I2C
master to configure the ADN8102 and other I2C devices that
may be on the bus. Data transfers are controlled using the two
I2C wires: the SCL input clock pin and the SDA bidirectional
data pin.
8.
9a.
9b.
9c.
The ADN8102 I2C interface can be run in the standard (100 kHz)
and fast (400 kHz) modes. The SDA line only changes value
when the SCL pin is low with two exceptions. To indicate the
beginning or continuation of a transfer, the SDA pin is driven
low while the SCL pin is high, and to indicate the end of a
transfer, the SDA line is driven high while the SCL line is high.
Therefore, it is important to control the SCL clock to toggle
only when the SDA line is stable, unless indicating a start,
repeated start, or stop condition.
9d.
Figure 42 shows the ADN8102 write process. The SCL signal is
shown along with a general write operation and a specific example.
In the example, Data 0x92 is written to Address 0x6D of an
ADN8102 part with a part address of 0x4B. The part address is
seven bits wide. The upper five bits of the ADN8102 are internally
set to 10010b. The lower two bits are controlled by the ADDR[1:0]
pins. In this example, the bits controlled by the ADDR[1:0] pins
are set to 11b. In Figure 42, the corresponding step number is
visible in the circle under the waveform. The SCL line is driven by
the I2C master and never by the ADN8102 slave. As for the SDA
line, the data in the shaded polygons is driven by the ADN8102,
whereas the data in the nonshaded polygons is driven by the I2C
master. The end phase case shown is that of Step 9a.
I2C INTERFACE DATA TRANSFERS—DATA WRITE
To write data to the ADN8102 register set, a microcontroller, or
any other I2C master, needs to send the appropriate control signals
to the ADN8102 slave device. The steps that need to be completed
are listed as follows, where the signals are controlled by the I2C
master, unless otherwise specified. A diagram of the procedure
can be seen in Figure 42.
2.
3.
4.
5.
6.
Send a start condition (while holding the SCL line high,
pull the SDA line low).
Send the ADN8102 part address (seven bits) whose upper
five bits are the static value 10010b and whose lower two
bits are controlled by the ADDR[1:0] input pins. This transfer
should be MSB first.
Send the write indicator bit (0).
Wait for the ADN8102 to acknowledge the request.
Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
Wait for the ADN8102 to acknowledge the request.
Note that the SDA line only changes when the SCL line is low,
except for the case of sending a start, stop, or repeated start
condition, Step 1 and Step 9 in this case.
SCL
GENERAL CASE
SDA
START
FIXED PART ADDR
ADDR
[1:0] R/W ACK
REGISTER ADDR
ACK
DATA
ACK
STOP
EXAMPLE
SDA
1
2
2
3
4
5
Figure 42. I2C Write Diagram
Rev. A | Page 26 of 32
6
7
8
9a
07060-008
1.
Send the data (eight bits) to be written to the register whose
address was set in Step 5. This transfer should be MSB first.
Wait for the ADN8102 to acknowledge the request.
Send a stop condition (while holding the SCL line high,
pull the SDA line high) and release control of the bus.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 in
this procedure to perform another write.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 of
the read procedure (in the I2C Interface Data Transfers—
Data Read section) to perform a read from another address.
Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 8 of
the read procedure (in the I2C Interface Data Transfers—
Data Read section) to perform a read from the same
address set in Step 5.
ADN8102
I2C INTERFACE DATA TRANSFERS—DATA READ
13a.
To read data from the ADN8102 register set, a microcontroller,
or any other I2C master, needs to send the appropriate control
signals to the ADN8102 slave device. The steps that need to be
completed are listed as follows, where the signals are controlled
by the I2C master, unless otherwise specified. A diagram of the
procedure can be seen in Figure 43.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13c.
Send a start condition (while holding the SCL line high,
pull the SDA line low).
Send the ADN8102 part address (seven bits) whose
upper five bits are the static value 10010b and whose
lower two bits are controlled by the input pins ADDR[1:0].
This transfer should be MSB first.
Send the write indicator bit (0).
Wait for the ADN8102 to acknowledge the request.
Send the register address (eight bits) from which data is
to be read. This transfer should be MSB first. The register
address is kept in memory in the ADN8102 until the
part is reset or the register address is written over with
the same procedure (Step 1 to Step 6).
Wait for the ADN8102 to acknowledge the request.
Send a repeated start condition (while holding the SCL
line high, pull the SDA line low).
Send the ADN8102 part address (seven bits) whose
upper five bits are the static value 10010b and whose
lower two bits are controlled by the input pins ADDR[1:0].
This transfer should be MSB first.
Send the read indicator bit (1).
Wait for the ADN8102 to acknowledge the request.
The ADN8102 then serially transfers the data (eight bits)
held in the register indicated by the address set in Step 5.
Acknowledge the data.
13d.
Figure 43 shows the ADN8102 read process. The SCL signal is
shown along with a general read operation and a specific example.
In the example, Data 0x49 is read from Address 0x6D of an
ADN8102 part with a part address of 0x4B. The part address is
seven bits wide. The upper five bits of the ADN8102 are internally
set to 10010b. The lower two bits are controlled by the ADDR[1:0]
pins. In this example, the bits controlled by the ADDR[1:0] pins
are set to 11b. In Figure 43, the corresponding step number is
visible in the circle under the waveform. The SCL line is driven
by the I2C master and never by the ADN8102 slave. As for the SDA
line, the data in the shaded polygons is driven by the ADN8102,
whereas the data in the nonshaded polygons is driven by the I2C
master. The end phase case shown is that of Step 13a.
Note that the SDA line changes only when the SCL line is low,
except for the case of sending a start, stop, or repeated start
condition, as in Step 1, Step 7, and Step 13. In Figure 43, A is the
same as ACK in Figure 42. Equally, Sr represents a repeated
start where the SDA line is brought high before SCL is raised.
SDA is then dropped while SCL is still high.
SCL
GENERAL CASE
SDA START
FIXED PART
ADDR
ADDR R/
[1:0] W
A
REGISTER ADDR
A Sr
FIXED PART
ADDR
ADDR R/
[1:0] W A
DATA
A
STOP
11
12
13a
EXAMPLE
SDA
1
2
2
3
4
5
6
7
8
Figure 43. I2C Read Diagram
Rev. A | Page 27 of 32
8
9
10
07060-009
1.
13b.
Send a stop condition (while holding the SCL line high,
pull the SDA line high) and release control of the bus.
Send a repeated start condition (while holding the SCL
line high, pull the SDA line low) and continue with Step 2
of the write procedure (in the I2C Interface Data
Transfers—Data Write section) to perform a write.
Send a repeated start condition (while holding the SCL
line high, pull the SDA line low) and continue with Step 2 of
this procedure to perform a read from a another address.
Send a repeated start condition (while holding the SCL
line high, pull the SDA line low) and continue with Step 8 of
this procedure to perform a read from the same address.
ADN8102
PCB DESIGN GUIDELINES
Proper RF PCB design techniques must be used for optimal
performance.
TRANSMISSION LINES
POWER SUPPLY CONNECTIONS AND GROUND
PLANES
Use of one low impedance ground plane is recommended.
The VEE pins should be soldered directly to the ground plane
to reduce series inductance. If the ground plane is an internal
plane and connections to the ground plane are made through
vias, multiple vias can be used in parallel to reduce the series
inductance. The exposed pad should be connected to the VEE
plane using plugged vias so that solder does not leak through
the vias during reflow.
Use of a 10 μF electrolytic capacitor between VCC and VEE is
recommended at the location where the 3.3 V supply enters the
printed circuit board (PCB). It is recommended that 0.1 μF and
1 nF ceramic chip capacitors be placed in parallel at each supply
pin for high frequency power supply decoupling. When using
0.1 μF and 1 nF ceramic chip capacitors, they should be placed
between the IC power supply pins (VCC, VTTI, and VTTO)
and VEE, as close as possible to the supply pins.
Use of 50 Ω transmission lines is required for all high frequency
input and output signals to minimize reflections. It is also necessary
for the high speed pairs of differential input traces to be matched in
length, as well as the high speed pairs of differential output traces,
to avoid skew between the differential traces.
SOLDERING GUIDELINES FOR CHIP SCALE PACKAGE
The lands on the LFCSP are rectangular. The PCB pad for these
should be 0.1 mm longer than the package land length and
0.05 mm wider than the package land width. Center the land on
the pad, which ensures that the solder joint size is maximized.
The bottom of the chip scale package has a central exposed pad.
The pad on the PCB should be at least as large as this exposed pad.
The user must connect the exposed pad to VEE using plugged vias
so that solder does not leak through the vias during reflow. This
ensures a solid connection from the exposed pad to VEE.
By using adjacent power supply and GND planes, excellent high
frequency decoupling can be realized by using close spacing
between the planes. This capacitance is given by
CPLANE = 0.88εr × A/d (pF)
where:
εr is the dielectric constant of the PCB material.
A is the area of the overlap of power and GND planes (cm2).
d is the separation between planes (mm).
For FR4, εr = 4.4, and 0.25 mm spacing, C ≈ 15 pF/cm2.
Rev. A | Page 28 of 32
ADN8102
REGISTER MAP
Table 17. I2C Register Definitions
Name
Reset
Global
Configuration
Control
Mode
TxHeadroom
IN_A
Configuration
IN_A LOS
Threshold
IN_A LOS
Hysteresis
IN_A LOS
Status 1
IN_A EQ1
Control
IN_A EQ2
Control
IN_A0 FR4
Control
IN_A1 FR4
Control
IN_A2 FR4
Control
IN_A3 FR4
Control
IN_B
Configuration
IN_B LOS
Threshold
IN_B LOS
Hysteresis
IN_B LOS
Status1
IN_B EQ1
Control
IN_B EQ2
Control
IN_B3 FR4
Control
IN_B2 FR4
Control
IN_B1 FR4
Control
IN_B0 FR4
Control
Address
0x00
0x02
0x0F
0x23
0x80
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Default
LB[1]
Bit 0
RESET
LB[0]
MODE[0]
TxH_A0
EQ[0]
0x00
0x00
0x30
0x00
TxH_B2
PNSWAP
TxH_B1
EQBY
TxH_B0
EN
TxH_A3
TxH_A2
EQ[2]
MODE[1]
TxH_A1
EQ[1]
0x81
THRESH[6]
THRESH[5]
THRESH[4]
THRESH[3]
THRESH[2]
THRESH[1]
THRESH[0]
0x04
0x82
HYST[6]
HYST[5]
HYST[4]
HYST[3]
HYST[2]
HYST[1]
HYST[0]
0x12
STICKY
LOS[2]
EQ CTL
SRC
STICKY
LOS[1]
EQ1[5]
STICKY
LOS[0]
EQ1[4]
REAL-TIME
LOS[3]
EQ1[3]
REAL-TIME
LOS[2]
EQ1[2]
REAL-TIME
LOS[1]
EQ1[1]
REAL-TIME
LOS[0]
EQ1[0]
0x00
EQ2[5]
EQ2[4]
EQ2[3]
EQ2[2]
EQ2[1]
EQ2[0]
0x00
LUT
FR4/CX4
LUT
FR4/CX4
LUT
FR4/CX4
LUT
FR4/CX4
EQ[0]
0x00
EQ[2]
LUT
SELECT
LUT
SELECT
LUT
SELECT
LUT
SELECT
EQ[1]
0x1F
TxH_B3
STICKY
LOS[3]
0x83
0x84
0x85
0x8D
0x95
0x9D
0x00
0x00
0x00
0xA0
PNSWAP
EQBY
EN
0xA1
THRESH[6]
THRESH[5]
THRESH[4]
THRESH[3]
THRESH[2]
THRESH[1]
THRESH[0]
0x04
0xA2
HYST[6]
HYST[5]
HYST[4]
HYST[3]
HYST[2]
HYST[1]
HYST[0]
0x12
STICKY
LOS [2]
EQ CTL
SRC
STICKY
LOS [1]
EQ1[5]
STICKY
LOS[0]
EQ1[4]
REAL-TIME
LOS[3]
EQ1[3]
REAL-TIME
LOS[2]
EQ1[2]
REAL-TIME
LOS[1]
EQ1[1]
REAL-TIME
LOS[0]
EQ1[0]
0x00
EQ2[5]
EQ2[4]
EQ2[3]
EQ2[2]
EQ2[1]
EQ2[0]
0x00
LUT
SELECT
LUT
SELECT
LUT
SELECT
LUT
SELECT
LUT
FR4/CX4
LUT
FR4/CX4
LUT
FR4/CX4
LUT
FR4/CX4
0x00
0x3F
0xA3
0xA4
STICKY
LOS [3]
0xA5
0xAD
0xB5
0xBD
Rev. A | Page 29 of 32
0x30
0x00
0x00
0x00
ADN8102
Name
OUT_A
Configuration
OUT_A
Output Level
Control 1
OUT_A
Output Level
Control 0
OUT_A
Squelch
Control
OUT_B
Configuration
OUT_B
Output Level
Control 1
OUT_B
Output Level
Control 0
OUT_B
Squelch
Control
1
Address
0xC0
Bit 7
0xC1
PE CTL
SRC
Bit 6
Bit 5
EN
Bit 4
DATA
RATE
0xC2
0xC3
Bit 1
PE[1]
Bit 0
PE[0]
EN
0x40
OUTA_OLEV0[6:0]
0x40
PE[2]
DATA
RATE
PE CTL
SRC
Default
0x20
OUTA_OLEV1[6:0]
0xFF
DISABLE[3:0]
0xE2
0xE3
Bit 2
PE[2]
SQUELCH[3:0]
0xE0
0xE1
Bit 3
PE[1]
PE[0]
0x20
OUTB_OLEV1[6:0]
0x40
OUTB_OLEV0[6:0]
0x40
SQUELCH[3:0]
Read-only register.
Rev. A | Page 30 of 32
DISABLE[3:0]
0xFF
ADN8102
OUTLINE DIMENSIONS
9.00
BSC SQ
0.60 MAX
8.75
BSC SQ
(BOTTOM VIEW)
33
32
17 16
7.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
SEATING
PLANE
0.50 BSC
*6.15
6.00 SQ
5.85
EXPOSED PAD
0.50
0.40
0.30
PIN 1
INDICATOR
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
*COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4
EXCEPT FOR EXPOSED PAD DIMENSION
080108-B
TOP
VIEW
12° MAX
64 1
49
48
PIN 1
INDICATOR
1.00
0.85
0.80
0.30
0.25
0.18
0.60 MAX
Figure 44. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
9 mm × 9 mm Body, Very Thin Quad
(CP-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADN8102ACPZ 1
ADN8102ACPZ-R71
ADN8102-EVALZ1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
Z = RoHS Compliant Part.
Rev. A | Page 31 of 32
Package Option
CP-64-2
CP-64-2
ADN8102
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07060-0-8/08(A)
Rev. A | Page 32 of 32