SGMICRO SGM2005

SGM2005
Low Power, Low Dropout,
150mA, RF - Linear Regulators
GENERAL DESCRIPTION
FEATURES
The SGM2005 series low-power, low-noise, low-dropout,
CMOS linear voltage regulators operate from a 2.5V to 5.5V
input and deliver up to 150mA. They are the perfect choice
for low voltage, low power applications. An ultra low
ground current ( 150µA at 150mA output ) makes these
parts attractive for battery operated power systems. The
SGM2005 series also offer ultra low dropout voltage
(150mV at 150mA output) to prolong battery life in
portable electronics. Systems requiring a quiet voltage
source, such as RF applications, will benefit from the
SGM2005 series’ ultra low output noise (30µVRMS) and
high PSRR. An external noise bypass capacitor connected
to the device’s BP pin can further reduce the noise level.
- Low Output Noise: 30µVRMS typ(10Hz to 100KHz)
- Ultra-Low Dropout Voltage:
150mV at 150mA output
- Low 77µA No-Load Supply Current
- Low 150µA Operating Supply Current
-
at 150mA Output
High PSRR: 73dB at 1KHz
Thermal-Overload Protection
Output Current Limit
Preset Output Voltages (±2.7% Accuracy)
10nA Logic-Controlled Shutdown
Available in Multiple Output Voltage Versions
Fixed Outputs of 1.8V, 2.5V, 2.8V, 3.0V and 3.3V
The output voltage is preset to voltages in the range of 1.5V
to 5.0V. Other features include a 10nA logic-controlled
shutdown mode, foldback current limit and thermal shutdown protection.
Devices come in 6-pin DFN-6 package.
PIN CONFIGURATIONS(TOP VIEW)
SGM2005
APPLICATIONS
Cellular Telephones
Cordless Telephones
PCS Telephones
PCMCIA Cards
Modems
MP3 Player
Hand-Held Instruments
Palmtop Computers
Electronic Planners
Portable/Battery-Powered Equipment
Shengbang Microelectronics Co, Ltd
Tel: 86/451/84348461
www.sg-micro.com
EN
1
6
BP
GND
2
5
NC
IN
3
4
OUT
DFN-6
NC = NO CONNECT
REV. B
ORDERING INFORMATION
MODEL
VOUT(V)
PINPACKAGE
SPECIFIED
TEMPERATURE
RANGE
ORDERING
NUMBER
PACKAGE
MARKING
PACKAGE
OPTION
SGM2005-1.8
1.8V
DFN-6
- 40°C to +85°C
SGM2005-1.8YD6/TR
Y518
Tape and Reel, 3000
SGM2005-2.5
2.5V
DFN-6
- 40°C to +85°C
SGM2005-2.5YD6/TR
Y525
Tape and Reel, 3000
SGM2005-2.8
2.8V
DFN-6
- 40°C to +85°C
SGM2005-2.8YD6/TR
Y528
Tape and Reel, 3000
SGM2005-3.0
3.0V
DFN-6
- 40°C to +85°C
SGM2005-3.0YD6/TR
Y530
Tape and Reel, 3000
SGM2005-3.3
3.3V
DFN-6
- 40°C to +85°C
SGM2005-3.3YD6/TR
Y533
Tape and Reel, 3000
ABSOLUTE MAXIMUM RATINGS
IN to GND.....................................................................- 0.3V to +6V
Output Short-Circuit Duration ...........................................Infinite
EN to GND...................................................................- 0.3V to +6V
OUT, BP to GND............................................- 0.3V to (VIN + 0.3V)
Power Dissipation, PD @ TA = 25°C
DFN-6 ................................................................................... 300mW
Package Thermal Resistance
DFN-6,θJA ...........................................................................200℃/W
Operating Temperature Range..............................- 40°C to +85°C
Junction Temperature...........................................................+150°C
Storage Temperature.............................................- 65°C to +150°C
Lead Temperature (soldering, 10s).....................................+260°C
ESD Rating..................................................................................4 kV
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational
sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
TYPICAL OPERATION CIRCUIT
INPUT
2.5V TO 5.5V
OUTPUT
OUT
IN
CIN
1μF
ON
OFF
COUT
1μF
SGM
2005
BP
EN
GND
2
CBP
0.01μF
SGM2005
ELECTRICAL CHARACTERISTICS
(VIN = VOUT (NOMINAL) + 0.5V (1), TA = - 40°C to +85°C, unless otherwise noted. Typical values are at TA = + 25°C.)
PARAMETER
Input Voltage
SYMBOL
CONDITIONS
MIN
VIN
IOUT =1mA to150mA, TA = +25°C
VOUT + 0.5V≤VIN≤ 5.5V
Output Voltage Accuracy(1)
Maximum Output Current
Current Limit
Ground Pin Current
ILIM
IQ
UNITS
2.5
5.5
V
-2.7
+2.7
%
160
Load Regulation
ΔVLDR
en
PSRR
600
77
IOUT = 150mA, EN = 2V
150
mA
145
µA
1
IOUT = 150mA
ΔVLNR
mA
No load, EN = 2V
IOUT = 1mA
Line Regulation(1)
Power Supply Rejection Rate
MAX
150
Dropout Voltage (2)
Output Voltage Noise
TYP
VIN = 2.5V or (VOUT + 0.5V) to 5.5V,
IOUT = 1mA
IOUT = 0.1mA to 150mA, COUT = 1µF
f = 10Hz to 100KHz, CBP = 0.01µF,
COUT = 10µF
mV
150
190
0.03
0.15
%/V
0.0008
0.002
%/mA
30
µVRMS
CBP = 0.1µF, ILOAD = 50mA,
f = 100Hz,
78
dB
COUT = 1µF
f = 1KHz,
73
dB
SHUTDOWN
EN Input Threshold
VIH
VIL
2.0
VIN = 2.5V to 5.5V
0.4
TA = +25°C
0.01
TA = +85°C
0.01
TA = +25°C
0.01
TA = +85°C
0.01
TA = +25°C
30
µs
TSHDN
160
℃
ΔTSHDN
15
℃
EN Input Bias Current
IB(SHDN)
EN = 0V and EN = 5.5V
Shutdown Supply Current
IQ(SHDN)
EN = 0.4V
CBP = 0.01µF
Shutdown Exit Delay(3)
COUT = 1µF, No load
1
V
1
µA
µA
THERMAL PROTECTION
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Specifications subject to change without notice.
Note 1: VIN = VOUT(NOMINAL) + 0.5V or 2.5V, whichever is greater.
Note 2: The dropout voltage is defined as VIN - VOUT, when VOUT is 100mV below the value of VOUT for VIN = VOUT + 0.5V. (Only applicable
for VOUT = +2.5V to +3.3V.)
Note 3: Time needed for VOUT to reach 95% of final value.
3
SGM2005
TYPICAL OPERATING CHARACTERISTICS
VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted.
Output Voltage vs.Load Current
3.4
2.85
3.35
Output Voltage(V)
Output Voltage(V)
Output Voltage vs.Load Current
2.9
2.8
2.75
3.3
3.25
VOUT = 2.8V
VOUT = 3.3V
2.7
3.2
0
50
100
Load Current(mA)
150
0
Ground Pin Current vs.Load Current
150
Ground Pin Current vs.Input Voltage
200
160
VOUT = 2.8V
150
140
130
Ground Pin Current(µA)
Ground Pin Current(µA)
50
100
Load Current(mA)
VOUT = 3.3V
120
110
100
VOUT = 2.8V
90
80
160
Iload = 50mA
120
80
No Load
40
70
60
0
0
50
100
Load Current(mA)
150
0
Ground Pin Current vs.Input Voltage
2
3
4
Input Voltage(V)
5
6
Output Voltage vs.Input Voltage
200
6
VOUT = 3.3V
No Load
5
Iload = 50mA
160
Output Voltage(V)
Ground Pin Current(µA)
1
120
80
No Load
40
VOUT = 3.3V
4
3
VOUT = 2.8V
2
1
0
0
0
1
2
3
4
Input Voltage(V)
5
0
6
4
1
2
3
4
Input Voltage(V)
5
6
SGM2005
TYPICAL OPERATING CHARACTERISTICS
VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted.
Output Voltage vs.Temperature
Output Voltage vs.Temperature
2.9
3.4
ILOAD = 150mA
Output Voltage(V)
2.85
2.8
2.75
3.35
3.3
3.25
VOUT = 3.3V
VOUT = 2.8V
2.7
3.2
-40 -25 -10
5
20 35 50
Temperature(℃)
65
80
95
-40 -25 -10
220
240
200
220
180
200
VOUT = 3.3V
180
160
140
120
VOUT = 2.8V
100
160
65
80
95
TA = +85℃
140
TA = +25℃
120
100
TA = -40℃
80
60
40
ILOAD = 150mA
80
5
20 35 50
Temperature(℃)
Dropout Voltage vs.Load Current
260
Dropout Voltage(mV)
Ground Pin Current(μA)
Ground Pin Current vs.Temperature
VOUT = 2.8V
20
0
60
-40 -25 -10
5
20 35 50
Temperature(℃)
65
80
0
95
Dropout Voltage vs.Load Current
1000
160
900
140
TA = +85℃
120
TA = +25℃
100
80
TA = -40℃
60
40
VOUT = 3.3V
20
15
30
45 60 75 90 105 120 135 150
Load Current(mA)
Current limit vs.Temperature
180
Current limit(mA)
Dropout Voltage(mV)
Output Voltage(V)
ILOAD = 150mA
800
700
VOUT = 3.3V
600
500
VOUT = 2.8V
400
300
200
0
100
0
15
30
45
-50 -35 -20
60 75 90 105 120 135 150
Load Current(mA)
5
-5 10 25 40
Temperature(℃)
55
70
85
SGM2005
TYPICAL OPERATING CHARACTERISTICS
VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted.
6
SGM2005
TYPICAL OPERATING CHARACTERISTICS
VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted.
Power-Supply Rejection Ratio
vs.Frequency
Output Noise Spectral Density
vs.Frequency
100
80
Output Noise Spectral Density
(μV/√Hz)
90
PSRR(dB)
10
CBP = 0.1μF
ILOAD = 50mA
VIN = VOUT+1V
70
COUT = 10μF
60
50
1
COUT = 1μF
0.1
40
COUT = 1μF
30
20
0.01
CBP = 0.01μF
ILOAD = 50mA
0.1
1
10
Frequency(kHz)
100
0.01
0.01
1000
COUT = 10μF
0.1
1
10
100
1000
Frequency(kHz)
Output Noise vs.Load Current
50
Output Noise(µVRMS)
45
VOUT = 3.3V
40
35
30
25
VOUT = 2.8V
20
f = 10Hz to 100kHz
CBP = 0.01μF
COUT = 10μF
15
10
5
0
1
10
100
Load Current(mA)
1000
7
SGM2005
Application Notes
When LDO is used in handheld products, Attention must be paid to voltage spike which would damage
SGM2005. In such applications, voltage spike will be generated at changer interface and VBUS pin of USB
interface when changer adapters and USB equipments are hot-inserted. Besides this, handheld products will
be tested on the production line on the condition of no battery. Test Engineer will apply power from the
connector pin which connects with positive pole of the battery. When external power supply is turned on
suddenly, the voltage spike will be generated at the battery connector. The voltage spike will be very high, it
always exceeds the absolute maximum input voltage (6.0V) of LDO. In order to get robust design. Design
Engineer needs to clear up this voltage spike. Zener diode is a cheap and effective solution to eliminate such
voltage spike. For example, BZM55B5V6 is a 5.6V small package Zener diode which can be used to
remove voltage spike in cell phone design. The schematic is shown in below:
Vcc
Input
BZM55B5V6
IN
1uF
VOUT
SGM2005
C1
EN
GND
VOUT
C2
4.7uF
BP
0.01uF
Control
8
SGM2005
PACKAGE OUTLINE DIMENSIONS
0.650±0.050
2.000±0.050
Top View
PIN #1 IDENTIFICATION
N3
N1
0.250±0.050
Bottom View
0~0.050
0.203±0.025
0.750±0.050
N6
1.200±0.100
0.700±0.100
2.000±0.050
N4
0.350±0.050
DFN-6
Side View
NOTES:
1. All dimensions are in millimeters.
9
SGM2005
REVISION HISTORY
Location
Page
03/07— Data Sheet changed from REV. A to REV. B
Changed to TYPICAL OPERATING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Shengbang Microelectronics Co, Ltd
Unit 3, ChuangYe Plaza
No.5, TaiHu Northern Street, YingBin Road Centralized Industrial Park
Harbin Development Zone
Harbin, HeiLongJiang 150078
P.R. China
Tel.: 86-451-84348461
Fax: 86-451-84308461
www.sg-micro.com
10
SGM2005