117142_C30659.qxd 6/21/04 2:33 PM Page 1 Preliminary Data Sheet C30659-900-1060-1550nm Series Silicon and InGaAs APD Preamplifier Modules Applications Range Finding LIDAR Featur es System bandwidth 50 MHz and 200 MHz Ultra low noise equivalent power (NEP) Spectral response range: Silicon APD: 400 to 1100nm InGaAs APD: 1100 to 1700nm Power consumption (150 mW typ.) +/-5 Volts amplifier operating voltages 50 Ω AC Load capability Description Hermetically sealed TO-8 packages PerkinElmer C30659 Series includes a Silicon or InGaAs Avalanche Photodiode with a hybrid preamplifier. It is supplied in a single modified 12-lead TO-8 package. The avalanche photodiodes used in these devices are the C30817E, C30902E, C30954E, C30956E, C30645E and C30662E that provide very good response between 830 and 1550 nanometers and very fast rise and fall times at all wavelengths. The preamplifier section uses a very low noise GaAs FET front end designed to operate at higher transimpedance than the regular C30950 series. The C30659 is pin to pin compatible with the C30950 series. The output of the C30659 is negative. An emitter follower is used as an output buffer stage. To obtain the wideband characteristics, the output of these devices should be AC (capacitively) coupled to a 50 Ohm termination. The module must not be DC coupled to loads of less than 2,000 Ohms. High reliability Fast overload recovery Pin compatible with the C30950 series Light entry angle ∅130° For field use, it is recommended that a temperature compensated HV supply be employed to maintain responsivity constant over temperature. w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m D A T A S H E E T Confocal Microscope P R E L I M I N A R Y Optoelectronics 117142_C30659.qxd 6/21/04 2:33 PM Page 2 C30659-900nm Series Table 1. Electrical Characteristics at TA=22ºC Test Conditions: Ambient Temperature, Vamp = ±5 Volts, HV = +VR (see Note 1), R L = 50Ω AC Coupled 900nm Silicon APD Detector Type C30659-900-R8A (Si APD C30817E) Min Typ Max 0.8 0.5 50 C30659-900-R5B (Si APD C30902E) Min Typ Max 0.5 0.2 200 275 -1.8 2.2 Note 1 -2.1 435 -2.4 180 -1.8 0.7 Note 1 -2.1 260 -2.4 V/°C V mV/°C - 2700 3000 82 - - 460 400 12 - kV/W kV/W kΩ - 14 12 17 15 - 35 40 55 65 fW/√Hz fW/√Hz 33 40 35 40 50 45 50 - 33 175 15 40 200 25 50 - nV/√Hz Ω MHz - 7 - - 2 - ns - 7 - - 2 - ns Recovery time after overload (note 4) - - 150 - - 150 ns Output Voltage Swing (1kΩ load) (note 5) 2 3 - 2 3 - V Output Voltage Swing (50Ω load) (note 5) 0.7 0.9 - 0.7 0.9 - V Output Offset Voltage -1 0.25 1 Positive Supply Current (V+) - 20 Negative Supply Current (V-) - 10 Active Diameter Active Area Bandwidth Range Temperature Coefficient of VR for constant Gain VR for specified responsivity Temperature sensor sensitivity Responsivity At 830nm At 900nm RF (Internal Feedback Resistor) Noise Equivalent Power (NEP) (note 3) f - 100 kHz, ∆f = 1.0 Hz At 830nm At 900nm Output Spectral Noise Voltage: (f = 100 kHz - f-3dB) Output Impedance System Bandwidth, f-3dB Rise Time, tr (λ = 830 and 900nm) 10% to 90% points Fall Time, tf (λ = 830 and 900nm) 90% to 10% points Notes: 1. 2. 3. 4. 5. mm mm2 MHz -1 0.25 1 V 35 - 20 35 mA 20 - 10 20 mA A specific value of VR is supplied with each device. The VR value will be within the specified ranges. If = 0.1 mA, 25°C NEPmax is the Maximum Output Spectral Noise Voltage max divided by the typical Responsivity. 0dBm, 250ns pulse. Pulsed operation. w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 2 117142_C30659.qxd 6/21/04 2:33 PM Page 3 C30659-1060nm Series Table 2. Electrical Characteristics at TA=22ºC Test Conditions: Ambient Temperature, Vamp = ±5 Volts, HV = +VR (see Note 1), RL = 50Ω AC Coupled 1060nm Silicon APD Detector Type C30659-1060-3A (Si APD C30956E) Min Typ Max 3.0 7.1 50 C30659-1060-R8B (Si APD C30954E) Min Typ Max 0.8 0.5 200 275 -1.8 2.2 Note 1 -2.1 425 -2.4 275 -1.8 2.2 Note 1 -2.1 425 -2.4 V/°C V mV/°C - 450 280 22 - - 370 200 12 - kV/W kV/W kΩ - 55 90 80 125 - 55 100 80 150 fW/√Hz fW/√Hz 33 40 25 40 50 35 50 - 33 175 20 40 200 30 50 - nV/√Hz Ω MHz - 7 - - 2 - ns - 7 - - 2 - ns Recovery time after overload (note 4) - - 150 - - 150 ns Output Voltage Swing (1kΩ load) (note 5) 2 3 - 2 3 - V Output Voltage Swing (50Ω load) (note 5) 0.7 0.9 - 0.7 0.9 - V Output Offset Voltage -1 0.25 1 -1 0.25 1 V Positive Supply Current (V+) - 20 35 - 20 35 mA Negative Supply Current (V-) - 10 20 - 10 20 mA Active Diameter Active Area Bandwidth Range Temperature Coefficient of VR for constant Gain VR for specified responsivity Temperature sensor sensitivity Responsivity At 900nm At 1060nm RF (Internal Feedback Resistor) Noise Equivalent Power (NEP) (note 3) f - 100 kHz, ∆f = 1.0 Hz At 900nm At 1060nm Output Spectral Voltage: (f = 100 kHz - f-3dB) Output Impedance System Bandwidth, f-3dB Rise Time, tr (λ = 900 and 1060nm) 10% to 90% points Fall Time, tf (λ = 830 and 900nm) 90% to 10% points Notes: 1. 2. 3. 4. 5. mm mm2 MHz A specific value of VR is supplied with each device. The VR value will be within the specified ranges. If = 0.1 mA, 25°C NEPmax is the Maximum Output Spectral Noise Voltage max divided by the typical Responsivity. 0dBm, 250ns pulse. Pulsed operation. w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 3 117142_C30659.qxd 6/21/04 2:33 PM Page 4 C30659-1550nm Series Table 3. Electrical Characteristics at TA=22ºC Test Conditions: Ambient Temperature, Vamp = ±5 Volts, HV = +VR (see Note 1), RL = 50Ω AC Coupled 1550nm InGaAs APD Detector Type C30659-1550-R2A (InGaAs APD C30662E) Min Typ Max 0.2 0.03 50 C30659-1550-R08B (InGaAs APD C30645E) Min Typ Max 0.08 0.005 200 40 -1.8 0.2 Note 1 -2.1 70 -2.4 40 -1.8 0.2 Note 1 -2.1 70 -2.4 V/°C V mV/°C - 300 340 68 - - 80 90 18 - kV/W kV/W kΩ - 150 130 180 160 - 250 220 375 330 fW/√Hz fW/√Hz 33 40 45 40 50 55 50 - 33 175 20 40 200 30 50 - nV/√Hz Ω MHz - 7 - - 2 - ns - 7 - - 2 - ns Recovery time after overload (note 4) - - 150 - - 150 ns Output Voltage Swing (1kΩ load) (note 5) 2 3 - 2 3 - V Output Voltage Swing (50Ω load) (note 5) 0.7 0.9 - 0.7 0.9 - V Output Offset Voltage -1 -0.3 1 -1 -0.3 1 V Active Diameter Active Area Bandwidth Range Temperature Coefficient of VR for constant Gain VR for specified responsivity Temperature sensor sensitivity Responsivity At 1300nm At 1550nm RF (Internal Feedback Resistor) Noise Equivalent Power (NEP) (note 3) f - 100 kHz, ∆f = 1.0 Hz At 1300nm At 1550nm Output Spectral Voltage: (f = 100 kHz - f-3dB) Output Impedance System Bandwidth, f-3dB Rise Time, tr (λ = 900 and 1060nm) 10% to 90% points Fall Time, tf (λ = 830 and 900nm) 90% to 10% points mm mm2 MHz Positive Supply Current (V+) - 20 35 - 20 35 mA Negative Supply Current (V-) - 10 20 - 10 20 mA Notes: 1. 2. 3. 4. 5. A specific value of VR is supplied with each device. The VR value will be within the specified ranges. If = 0.1 mA, 25°C NEPmax is the Maximum Output Spectral Noise Voltage divided by the typical Responsivity. 0dBm, 250ns pulse. Pulsed operation. w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 4 117142_C30659.qxd 6/21/04 2:33 PM Page 5 C30659-900-1060-1550nm Series Figure 1. C30659 Series Block Diagram 10k V+ (12) +HV (4) 10n RF 2.2k Photodiode T8_Anode (8) 33 D1N914 OUT (1) T8_Cathode (9) D. 7V +yp Ground (6) (10) 10n V- (3) Figure 2. Spectral Responsivity C30659-900-R8A C30659-1060-3A C30659-900-R5B C30659-1060-R8B w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 5 117142_C30659.qxd 6/21/04 2:33 PM Page 6 C30659-900-1060-1550nm Series Figure 2. Spectral Responsivity, continued C30659-1550-R2A C30659-1550-R08B Figure 3. Responsivity C30659-900-R8A C30659-900-R5B C30659-1060-3A C30659-1060-R8B w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 6 117142_C30659.qxd 6/21/04 2:33 PM Page 7 C30659-900-1060-1550nm Series Figure 3. Responsivity, continued C30659-1550-R2A C30659-1550-R08B Figure 4. Typical Response / Noise Curves 50 MHz Receivers Noise Frequency Noise Frequency 200 MHz Receivers Output voltage noise normalization is calculated using the following formula: w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 7 117142_C30659.qxd 6/21/04 2:33 PM Page 8 C30659-900-1060-1550nm Series Table 4. Absolute - Maximum Ratings, Limiting Values C30659-900 (Si) Min Typ Max Photodiode Bias Voltage: At TA = +70°C At TA = - 40°C C30659-1060 (Si) Min Typ Max C30659-1550 (InGaAs) Min Typ Max - - 600 300 - - 600 300 - - 100 50 V V - - 0.11 502 - - 0.11 502 - - 21 502 mW mW Case Temperature: Storage, Tstg Operating, TA -50 -40 - 100 70 -50 -40 - 100 70 -50 -40 - 100 70 °C °C Preamplifier Voltage: -4.5 - -5.5 -4.5 - -5.5 -4.5 - -5.5 V Incident Radiant Flux average peak ΦM Notes: 1. Based on 0.5W electrical power on high voltage supply. 2. Test with pulse width of 50 ns. Figure 5. Mechanical Characteristics PIN CONNECTIONS 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: 11: 12: Signal Output No Connection -Vcc Negative Amplifier Bias Positive high voltage No Connection Case Ground No Connection Temp. Sensing Diode - Anode Temp. Sensing Diode - Cathode Ground, DC returns No Connection +Vcc Positive Amplifier Bias w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 8 117142_C30659.qxd 6/21/04 2:33 PM Page 9 C30659-900-1060-1550nm Series Figure 6. Optical Geometry Model Detector S1 (mm) S2 (mm) d1 (mm) α (deg) C30659-900-R8A C30817E 0.80 11 1.4 70 C30659-900-R5B C30902E 0.50 11 1.4 70 C30659-1060-3A C30956E 3.00 11 1.3 65 C30659-1060-R8B C30954E 0.80 11 1.3 70 C30659-1550-R2A C30662E 0.20 11 1.5 70 C30659-1550-R08B C30645E 0.08 11 1.5 70 Table 5. Ordering Guide Model Description C30659-900-R8A 50 MHz, 900nm, 0.8mm Active Region Diameter C30659-900-R5B 200 MHz, 900nm, 0.5mm Active Region Diameter C30659-1060-3A 50 MHz, 1060nm, 3mm Active Region Diameter C30659-1060-R8B 200 MHz, 1060nm, 0.8mm Active Region Diameter C30659-1550-R2A 50 MHz, 1550nm, 0.2mm Active Region Diameter C30659-1550-R08B 200 MHz, 1550nm, 0.08mm Active Region Diameter Or dering Information While the information in this data sheet is intended to describe the form, fit and function for this product, PerkinElmer reserves the right to make changes without notice. For more information e-mail us at [email protected] or visit our web site at www.optoelectronics.perkinelmer.com. All values are nominal; specifications subject to change without notice. PerkinElmer Canada Inc. 16800 Trans Canada Highway Kirkland, Québec, H9H 5G7 Canada Phone: (514) 683-2200 Fax: (514) 693-2210 PerkinElmer GmbH & Co. KG Wenzel-Jaksch-Str.31 65199 Wiesbaden Phone: +49 611 492 247 Fax: +49 611 492 170 PerkinElmer Singapore Pte Ltd. 47 Ayer Rajah Crescent #06-12 Singapore 139947 Phone: +65 6775 2022 Fax: +65 6775 1008 Optoelectronics Headquarters PerkinElmer Optoelectronics 44370 Christy Street Fremont, CA 94538-3180 Phone: (510) 979-6500 (800) 775-6786 Fax: (510) 687-1140 ©2004 PerkinElmer Inc. All rights reserved. w w w . o p t o e l e c t r o n i c s . p e r k i n e l m e r. c o m Page 9