DC/DC Converters TMV-EN Series, 1 Watt CB Features ◆ Isolation test voltage 6’000 Vpk ◆ With reinforced insulation, rated for Scheme UL 60950-1 250 Vrms working voltage ◆ Physical clearance of isolation barrier 2.0 mm min. ◆ Certified to IEC/EN/UL 60950-1 Safety Standards ◆ Safety barrier 100% production test ◆ Low coupling capacity ◆ Single-in-line package (SIP) ◆ Lead-free design, RoHS compliant ◆ 3-year product warranty The TMV-EN series is a range of 1 W DC/DC converters with high I/O-isolation. This product features an isolation barrier which is approved for supplementary an reinforced insulation. SMD construction and a special designed toroidal transformer made it possible to built these converters in a standard SIP package with a very small footprint. These features making the TMV-EN series an economical solution in many DC/DC converter applications requiring safety agency approval. Models Order code Input voltage Output voltage Output current max. Efficiency typ. TMV 0505EN 5 VDC 200 mA 65 % TMV 0512EN 12 VDC 80 mA 65 % TMV 0515EN 15 VDC 65 mA 65 % TMV 0505DEN ± 5 VDC ±100 mA 65 % TMV 0512DEN ±12 VDC ± 40 mA 71 % TMV 0515DEN ±15 VDC ± 30 mA 72 % TMV 1205EN 5 VDC 200 mA 65 % TMV 1212EN 12 VDC 80 mA 65 % TMV 1215EN 15 VDC 65 mA 65 % TMV 1205DEN ± 5 VDC ±100 mA 65 % TMV 1212DEN ±12 VDC ± 40 mA 73 % TMV 1215DEN ±15 VDC ± 30 mA 74 % http://www.tracopower.com 5 VDC ±10 % 12 VDC ±10 % Page of 3 DC/DC Converters TMV-EN Series1 Watt Input Specifications Input current no load/full load 5 Vin models: 55 mA/300 mA typ. 12 Vin models: 30 mA/125 mA typ. Surge voltage (1 sec. max.) 5 Vin models: 9 V max. 12 Vin models: 18 V max. Reverse voltage protection 0.3 A max. Reflected input ripple current can be reduced by ext. 1–3.3 µF polyester film capacitor Input filter internal capacitor Output Specifications Voltage set accuracy ±3 % Voltage balance (dual output models) ±1 % max. Regulation – Input variation ±1.2 %/1% change Vin – Load variation 20 – 100 % <10 % Ripple and noise (20 MHz Bandwidth) 120 mV pk-pk typ. Temperature coefficient ±0.02 %/K Short circuit protection limited 1 sec. max. Capacitive load single output models: 680 µF max. dual output models: 220 µF max. Isolation /Safety Isolation voltage – Isolation test voltage (tested for 1 sec.) 6‘000 Vpk – I/O isolation voltage (60 sec.) 3’000 VACrms Isolation capacity (input/output) 10 pF typ. Isolation resistance (input/output) >1‘000 Mohm Working voltage (rated) 300 VACrms Safety standards IEC/EN 60950-1, UL 60950-1 CSA C22.2 No. 60950-1-03 Safety approvals – CB report www.tracopower.com/products/tmv-en_cb.pdf – CSA certification www.tracopower.com/products/tmv-en_csa.pdf General Specifications Temperature ranges – Operating –40 °C to +85 °C – Case temperature +105 °C max. – Storage –40 °C to +125 °C Derating 4 %/K above 70 °C Humidity (non condensing) 95 % rel H max. Temperature coefficient ±0.02 %/K typ. Reliability, calculated MTBF (MIL-HDBK-217E) >2’000’000 h @ 25 °C Switching frequency 50 kHz typ. (frequency modulation) Frequency change over line and load ±30 % max. All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page of 3 DC/DC Converters TMV-EN Series1 Watt Physical Specifications Case material non-conducting FR4 (UL 94V-0 rated) Package weight 4.0 g (0.14 oz) Soldering temperature max. 265°C / 10 sec Outline Dimensions 0.5 (0.02) 3.5 2.54 7.62 2.54 2.54 (0.14 (0.1) ±0.02) (0.3) (0.1) (0.1) ± 0.5 12.5 (0.49) (0.16) 4.0 0.5 (0.02) Pin-Out Pin Single Dual 1 +Vin (Vcc) +Vin (Vcc) 2 –Vin (GND) –Vin (GND) 5 –Vout –Vout 6 No pin Common 7 +Vout +Vout 0.5 (0.02) 5 6 7 0.5 (0.02) 7.5 (0.3) 2 5.5 (0.22) 1 2 (0.08) Bottom view 0.25 (0..01) 22.0 (0.87) () = inches Tolerances ±0.25 (0.01) pins ±0.05 (0.002) Specifications can be changed any time without notice. Rev. 11/07.1 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · [email protected] · www.tracopower.com Page of 3