APDS-9007 Ambient Light Photo Sensor with Logarithmic Current Output Data Sheet Description Features The APDS-9007 is an analog current output Ambient Light Photo Sensor, packaged in a miniature chipLED lead-free surface mount package. • Excellent responsivity Close responsivity to the human eye This device provides a Logarithmic response over a wide dynamic range of 3 lux to 70K lux and has a low sensitivity variation across various light sources. It is well suited for applications that operates under high ambient brightness. Application Support Information The Application Engineering Group is available to assist you with the application design associated with APDS9007 ambient light photo sensor module. You can contact them through your local sales representatives for additional details. • Miniature ChipLED Leadfree surface-mount package Height – 0.8 mm Length – 2.4 mm Width – 2.0 mm • Low sensitivity variation across various light sources • Operating temperature : -40°C to 85°C • Vcc supply 2 to 3.6V • Lead-free package with RoHS compliance • Photo current response to wide dynamic range of 3 lux to 70K lux Applications • Detection of ambient light to control display backlighting Mobile devices – Mobile phones, PDAs Computing devices – Notebooks, Webpads Consumer devices – TVs, Video Cameras, Digital Still Camera • Automatic Residential and Commercial Lighting Management • Electronic Signs and Signals Ordering Information Part Number Packaging Type Package Quantity APDS-9007-020 Tape and Reel 6-pins Chipled package 2500 Typical Application Circuit I/O Pins Configuration Table Pin 4: VCC Pin 6: SD APDS9007 Pin 3: OUT RLoad Pin 1: GND Pin Symbol Description 1 Gnd Ground 2 NC * No Connect 3 Out Output 4 Vcc Supply Voltage 5 NC * No Connect 6 SD Shutdown (Active High) GND GND Figure 1. Typical application circuit for APDS-9007 (RLoad = 27 K Ohm) Absolute Maximum Ratings For implementations where case to ambient thermal resistance is ± 50 °C /W Parameter Symbol Min. Max. Units Storage Temperature TS -40 85 °C Supply Voltage VCC 0 3.6 V Recommended Operating Conditions Parameter Symbol Min. Max. Units Operating Temperature TA -40 85 °C Supply Voltage VCC 2 3.6 V Conditions CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD Electrical & Optical Specifications (Ta=25C) : Parameter Symbol Min. Typ. Max. Supply Current Icc Photo Current output (I) I_PH1 Photo Current output (II) I_PH2 36 Light Current Ratio I_PH2 / I_PH1 1.2 Rise Time Tr 0.2 mSec Rload = 27K ohms, 1K lux,Vcc = 3V Fall Time 0.2 mSec Rload = 27K ohms, 1K lux, Vcc = 3V Peak sensitivity wavelength Tf l 560 nm SD Current Icc-SD Output Compliance Voltage Vout 230 21 30 39 Units Conditions µA LUX=1K, Vcc=3V uA Lux=1K, Vcc=3V (Note 1,3) Lux=1K, Vcc=3V (Note 2,3) 1 Vcc-0.5 µA Vcc=3V, SD=3V Volts RLoad=100K, Vcc=3V (Refer Figure 7) Notes : 1. White LED is used as light source 2. Illuminance by incandescent lamp 3. Photo Current (I out) = 10uA x Log (Lux) Functional Block Diagram VCC Log Fn V2I & Mirror OUT Temperature Compensation GND Light Measurement Circuit and Waveforms I-Pulse Pin 4: VCC I-Pulse Pin 3: OUT APDS-9007 Load LED R Load Pin 1: GND VOUT 90% 10% GND GND GND GND Tr Tf 1 Relative response Relative output response APDS-9007 0.8 Eye Response 0.6 0.4 0.2 0 300 500 700 900 1100 -90 -75 -60 -45 -30 Wavelength in nm 60 75 90 1.5 Rel IOUT Avg IOUT 45 2.0 1.0 0.5 0.0 10 100 1000 10000 2 100000 2.5 3 LUX 3.5 4 3.5 4 Supply Voltage Figure 3. Average Iout vs Lux ,T=25°C Figure 4. Relative Iout Vs Vcc @ 1K LUX , T=25°C 1.10 250.0E-6 1.00 200.0E-6 0.90 Supply Current Avg REL IOUT 30 Figure 2. Angular Response plot 50.0E-6 45.0E-6 40.0E-6 35.0E-6 30.0E-6 25.0E-6 20.0E-6 15.0E-6 10.0E-6 5.0E-6 000.0E+0 1 0.80 0.70 150.0E-6 100.0E-6 50.0E-6 0.60 000.0E+0 10 60 110 2 Figure 5. Relative Iout Vs Temperature 2.5 3 Supply Voltage in Volts TEMP 15 Angle in Degrees Figure 1. Spectral Response 0.50 -40 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -15 0 Figure 6. Icc Vs Vcc, T=25°C 200.0E-6 3500 3000 160.0E-6 120.0E-6 2000 Tr Avg V-out [mV] 2500 1500 80.0E-6 1000 40.0E-6 500 000.0E+0 0 1 10 100 1000 10000 100000 LUX 0 160.8E-6 120.8E-6 80.8E-6 40.8E-6 800.0E-9 0 10000 20000 30000 40000 LOAD Figure 9. Fall Time Vs RLoad(Ohm) 3.000 Rload = 10kohm 2.500 Rload = 15kohm Rload = 27kohm Vout (V) 2.000 Rload = 36kohm 1.500 Rload = 56kohm 1.000 Rload = 75kohm 0.500 0.000 1 10 100 1000 Lux Figure 10. Average Vout vs Lux 10000 100000 20000 LOAD Figure 8. Rise Time Vs RLoad (Ohm) Figure 7. Output Compliance Voltage plot Tf 10000 30000 40000 APDS-9007 Package Outline Note: Active Area : Center of the device APDS-9007 Tape and Reel Dimension Moisture Proof Packaging UNITS IN A SEALED MOISTURE-PROOF PACKAGE PACKAGE IS OPENED (UNSEALED) PARTS ARE NOT RECOMMENDED TO BE USED NO ENVIRONMENT LESS THAN 30 C AND LESS THAN 60%RH YES PACKAGE IS OPENED LESS THAN 168 HOURS YES NO BAKING IS NECESSARY NO NO PACKAGE IS OPENED LESS THAN 15 DAYS YES PERFORM RECOMMENDED BAKING CONDITIONS All APDS-9007 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC Level 3. Baking Conditions: Package Temperature Time In Reel 60°C 48 hours In Bulk 100°C 6 hours * Baking should only be done once. Recommended Storage Conditions: Storage Temperature 10°C to 30°C Relative Humidity below 60% RH Time from unsealing to soldering: After removal from the bag, the parts should be soldered within 168 hours if stored at the recommended storage conditions. If times longer than 168 hours are needed, the parts must be stored in a dry box. Recommended Reflow Profile MAX 260C T - TEMPERATURE (˚C) 255 R3 230 217 200 180 R2 R4 60 sec to 90 sec Above 217 C 150 R5 R1 120 80 25 0 P1 HEAT UP 50 100 150 200 P3 SOLDER REFLOW P2 SOLDER PASTE DRY 250 P4 COOL DOWN 300 t-TIME (SECONDS) Symbol DT Maximum DT/Dtime or Duration Heat Up P1, R1 25°C to 150°C 3°C/s Solder Paste Dry P2, R2 150°C to 200°C 100s to 180s Solder Reflow P3, R3 P3, R4 200°C to 260°C 260°C to 200°C 3°C/s -6°C/s Cool Down P4, R5 200°C to 25°C -6°C/s > 217°C 60s to 90s Peak Temperature 260°C - Time within 5°C of actual Peak Temperature >255°C 20s to 40s 25°C to 260°C 8mins Process Zone Time maintained above liquidus point , 217°C Time 25°C to Peak Temperature The reflow profile is a straight-line representation of a nominal temperature profile for a convective reflow solder process. The temperature profile is divided into four process zones, each with different DT/Dtime temperature change rates or duration. The DT/Dtime rates or duration are detailed in the above table. The temperatures are measured at the component to printed circuit board connections. In process zone P1, the PC board and component pins are heated to a temperature of 150°C to activate the flux in the solder paste. The temperature ramp up rate, R1, is limited to 3°C per second to allow for even heating of both the PC board and component pins. Process zone P2 should be of sufficient time duration (100 to 180 seconds) to dry the solder paste. The temperature is raised to a level just below the liquidus point of the solder. Process zone P3 is the solder reflow zone. In zone P3, the temperature is quickly raised above the liquidus point of solder to 260°C (500°F) for optimum results. The dwell time above the liquidus point of solder should be between 60 and 90 seconds. This is to assure proper coalescing of the solder paste into liquid solder and the formation of good solder connections. Beyond the recommended dwell time the intermetallic growth within the solder connections becomes excessive, resulting in the formation of weak and unreliable connections. The temperature is then rapidly reduced to a point below the solidus temperature of the solder to allow the solder within the connections to freeze solid. Process zone P4 is the cool down after solder freeze. The cool down rate, R5, from the liquidus point of the solder to 25°C (77°F) should not exceed 6°C per second maximum. This limitation is necessary to allow the PC board and component pins to change dimensions evenly, putting minimal stresses on the component. It is recommended to perform reflow soldering no more than twice. Appendix A: SMT Assembly Application Note 1.3 Adjacent Land Keepout and Solder Mask Areas 1.0 Solder Pad, Mask and Metal Stencil Aperture Adjacent land keep-out is the maximum space occupied by the unit relative to the land pattern. There should be no other SMD components within this area. Metal Stencil For Solder Paste Printing Stencil Aperture Note: Wet/Liquid Photo-Imageable solder resist/mask is recommended. Land Pattern Solder Mask The minimum solder resist strip width required to avoid solder bridging adjacent pads is 0.2 mm. 3.2 PCBA Figure A1. Stencil and PCBA Mounting Center 1.1 Recommended Land Pattern 0.9 0.7 4.2 0.9 0.8 Mounting Center 0.3 0.6 2.2 1.4 3.2 Figure A2. Recommended Land Pattern 1.2 Recommended Metal Solder Stencil Aperture It is recommended that a 0.11 mm (0.004 inches) thick stencil be used for solder paste printing. Aperture opening for shield pad is 0.9mm x 0.8mm (as per land pattern). This is to ensure adequate printed solder paste volume and no shorting. Aperture Opening 2.2 Figure A3. Solder Stencil Aperture 10 0.2 MIN. Figure A4. Adjacent Land Keepout and Solder Mask Areas 0.8 Unit: mm Unit: mm 0.1 1 3.2 Unit: mm Appendix B: Optical Window Design for APDS-9007 1.0 Optical Window Dimensions To ensure that the performance of the APDS-9007 will not be affected by improper window design, there are some constraints on the dimensions and design of the window. There is a constraint on the minimum size of the window, which is placed in front of the photo light sensor, so that it will not affect the angular response of the APDS-9007. This minimum dimension that is recommended will ensure at least a ±35° light reception cone. Table 1 and Figure B3 below show the recommended dimensions of the window. These dimension values are based on a window thickness of 1.0mm with a refractive index 1.585. Table 1. Recommended minimum dimension for optical window. All dimensions are in mm Figure B1 and B2 illustrate the two types of window that we have recommended which could either be a flat window or a flat window with light pipe. Flat window with Light Pipe WD (T+L+Z) Z D1 D1/D2 T/L/Z 1.5 0.5 2.15 - - 2.0 1.0 2.85 - - 2.5 1.5 3.55 - - 3.0 2.0 4.25 2.0/1.2 1.0/1.5/0.5 If a smaller window is required, a light pipe or light guide can be used. A light pipe or light guide is a cylindrical piece of transparent plastic, which makes use of total internal reflection to focus the light. The thickness of the window should be kept as minimum as possible because there is a loss of power in every optical window of about 8% due to reflection (4% on each side) and an additional loss of energy in the plastic material. Flat Window (L=0.0) The window should be placed directly on top of the light receiving area (active area) of the photo sensor to achieve better performance and if a flat window with a light pipe is used, dimension D2 should be 1.5mm to optimize the performance of APDS-9007. The recommended minimum window dimension is based on the assumption that the center of the window and the center of the light receiving of the photo sensor are the same. It is recommended that the tolerance for assembly be considered as well. The recommended minimum window size which will take into account of the assembly tolerance is defined as: D1 (min + assembly tolerance) = D1min + 2*(assembly tolerance) (Dimensions are in mm) D2 (min + assembly tolerance) = D2min + 2*(assembly tolerance) (Dimensions are in mm) D1 Top View Figure B1. Window Size Determination for Flat Window T WD L Z APDS-9007 Light Receving Area Figure B2. Window Design of Flat Window with Light Guide WD: Working Distance between window front panel & APDS-9007 D1: Window Diameter T: Thickness L: Length of Light Pipe D2: Light Pipe Diameter Z: Distance between window rear panel and APDS-9007 Figure B3 .Recommended Window Dimensions 11 D2 D1 2.1 Optical Window Material The material of the window is recommended to be polycarbonate. The surface finish of the plastic should be smooth, without any texture. The recommended plastic material for use as a window is available from Bayer AG and Bayer Antwerp N. V. (Europe), Bayer Corp.(USA) and Bayer Polymers Co., Ltd. (Thailand), as shown in Table 2. 12 Table 2. Recommended Plastic Materials Material number Visible light transmission Refractive index Makrolon LQ2647 87% 1.587 Makrolon LQ3147 87% 1.587 Makrolon LQ3187 85% 1.587 Appendix C: General Application Guide for APDS-9007 The APDS-9007 is an analog current output ambient light photo sensor whose spectral response is close to the CIE standard photopic observer. APDS-9007 consists of a photodiode and an IC that performs amplification of the photodiode output signal and conversion to a logarithmic output current. APDS-9007 is able to produce a high gain photo current that can be converted to an output voltage via a standard value external load resistor. APDS-9007 is then easily integrated into micro-controller that has an available A/D as shown in Figure C1 below. An analog logarithmic current output is able to represent the wide dynamic range of ambient light brightness level from near darkness environment to bright outdoor conditions correctly and accurately. For a logarithmic output, constant relative changes in the input values are converted to constant absolute changes in the output values. The magnitude of the output voltage, Vout is directly proportional to the photo current which is generated by the brightness of the light source shone on the photo sensor and the value of the load resistor used, RL. Increasing the brightness of the light source and/or the value of the load resistor will increase the magnitude of the output voltage. A logarithmic current output is advantageous because when measuring low brightness levels, small changes in those levels need to be detected. For example, a change from 100lux to 200lux needs to be detected. On the other hand, when measuring high brightness levels, only relatively large changes need to be detected. For example, a change from 10000lux to 10200lux can be negligible and a change from 10klux to 20klux needs to be detected instead. The unit used to measure light in terms of what our eyes perceive is “LUX”. It indicates the intensity to which a surface is lit or the brightness of the light. Light sources with the same LUX level appear at the same brightness to the human eyes. The equipment for “LUX” measurement is a lux meter. Hence APDS-9007, with a logarithmic current output, is able to provide a good relative resolution over the entire ambient light brightness range. It is able to measure small current steps at low brightness levels and yet, at high brightness levels, it is not required to measure the current at such fine absolute resolutions. Selection of the load resistor RL will determine the amount of current-to-voltage conversion in the circuit. APDS-9007 allows a maximum saturation output voltage of (Vcc – 0.5V). This is illustrated in Figure C2 below. A change from 10lux to 100lux and a change from 1klux to 10klux will both give a same relative change which is 10. This is equivalent to a constant absolute change in output current which is 10uA for both changes. Hence a change from 10lux to 100lux will result in a change of 10uA. Similarly, a change from 1klux to 10klux will also result in a change of 10uA. Artificial light sources such as fluorescent lamps or incandescent lamps produced ac noise with a frequency of 50/60Hz and 100Hz respectively. A capacitor of 10uF, which acts as a low-pass filter, is recommended to be added in parallel with the load resistor to filter out these interferences. APDS-9007 can be directly connected to the A/D of the micro-controller via one external load resistor which will give the same accuracy or resolution over a wide dynamic range. 45 Pin 3 : OUT APDS9007 Pin 6: ShutDown (Active High) Pin 1:� GND GND Figure C1. Configuration of APDS-9007 13 MicroController A/D RL C Output Current (uA) Light Source I2 = 40uA 40 Pin 4: VDD 35 �"I = I2 - I1 30 I1 = 30uA 25 20 I2 = 20uA 15 �"I = I2 - I1 10 5 0 I1 = 10uA 1 10 100 Lux Ev2 = 100lux Ev1 = 10lux �"Ev = Ev2/Ev1 = 10 1000 Ev1 = 1klux Figure C2. Feature of Logarithmic Output 10000 Ev2 = 10klux �"Ev = Ev2/Ev1 = 10 For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. AV02-0512EN - June 28, 2007