Cree® P4 LED Model # LP476PWN1-90G Data Sheet 90-degree, 7.6 x 7.6 mm LED lamp in white color with water-transparent lens and stopper Applications • • Indicators Illuminations Absolute Maximum Ratings (TA = 25°C) Items Symbol Absolute Maximum Rating Unit IF 30 mA IFP 100 mA Reverse Voltage VR 5 V Power Dissipation PD 132 mW Operation Temperature Topr -40 ~ +95 °C Storage Temperature Tstg -40 ~ +100 °C Lead Soldering Temperature Tsol Forward Current Peak Forward Current Note Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) Note: Pulse width ≤0.1 msec, duty ≤1/10. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Symbol Condition Unit Forward Voltage VF IF = 30 mA V Reverse Current IR VR = 5 V μA Luminous Intensity IV IF = 30 mA mcd Luminous Flux ΦV IF = 30 mA mlm x IF = 30 mA 0.31 y IF = 30 mA 0.32 2θ½H-H IF = 30 mA deg 95 2θ½V-V IF = 30 mA deg 40 D-CT128.000 Data Sheet: CL Chromaticity Coordinates 50% Power Angle Minimum Subject to change without notice. www.cree.com/ledlamps Typical Maximum 3.6 4.4 100 770 1500 2200 Standard Bins for LP476PWN1-90G (IF = 30 mA) Lamps are sorted to luminous intensity (IV), VF and chromaticity coordinates (x,y) bins shown. Orders for LP476PWN1-90G may be filled with any or all bins contained as below. All luminous intensity (IV), VF and chromaticity coordinates (x,y) values shown and specified are at IF = 30 mA. Luminous Intensity (IV) A1 A2 B1 B2 c V or above 2130 mcd U 1520 mcd T 1100 mcd S 770 mcd Chromaticity Coordinates (x,y) Rank Chromaticity x Coordinates y A1 A2 B1 0.245 0.264 0.280 0.264 0.264 0.283 0.296 0.280 0.283 0.307 0.313 0.296 0.229 0.267 0.248 0.220 0.267 0.305 0.276 0.248 0.305 0.337 0.297 0.276 Rank B2 Chromaticity x Coordinates y c 0.307 0.330 0.330 0.313 0.330 0.361 0.356 0.330 0.337 0.360 0.318 0.297 0.360 0.385 0.351 0.318 V7 V8 V9 V10 V11 V12 V13 V14 2.8-3.0 V 3.0-3.2 V 3.2-3.4 V 3.4-3.6 V 3.6-3.8 V 3.8-4.0 V 4.0-4.2 V 4.2-4.4 V Forward Voltage (VF) Rank Voltage Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Pb content <1000 ppm. 3. Tolerance of measurement of luminous intensity is ±15%. 4. Tolerance of measurement of the chromaticity coordinates is ±0.01. 5. Tolerance of measurement of VF is ±0.05 V. 6. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 7. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 8. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT128.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps CIE Chromaticity Diagram CIE CIE Chromaticity Diagram 0.90 520 530 0.80 540 510 550 0.70 560 0.60 570 490 0.50 Y 580 590 0.40 600 c 610 620 630 B2 0.30 B1 480 A2 A1 0.20 470 0.10 460 0.00 0.00 0.10 0.20 0.30 X 4/5 0.40 0.50 0.60 0.70 Format #: COTCO-D-074 REV.4 Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT128.000 0.80 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. SPE/LP476PWN1-90G Rev. No. 03 Graphs Graphs Items Prepared by Signatures Date LiuZM 2007-04-26 Revision History Rev. No Date Change Description Checked by HuangJD 2007-04-26 02 2005-10-18 Release. Change 2T½ from 90*35deg to 95*40deg; VF from V8~V13 to V7~V14. Approved by David 2007-04-26 03 2007-04-26 Change tolerance of CIE(x,y) from +/-0.015 to +/-0.01 FCN# FCN20070432 Data is subject to change without prior notice; please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT128.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Mechanical Dimensions Document No. SPE/LP476PWN1-90G Rev. No. 03 All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Dimension Drawing Burr around bottom of epoxy may be 0.5 mm max. e maximum Unit ating 30 mA 100 mA 5 V 132 mW ~ +95 °C ~ +100 °C 0°C for 3 sec Max. he base Notes of the epoxy bulb) RoHS Compliance cs ( The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the = 25 limits) Tathreshold ) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. °C Vision Advisory Claim Condition Min. Typ. Max. Unit IF = 30mA --- 3.6 4.4 V Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. All rights reserved. The information to change without notice. Cree and the VR = Copyright 5V © 2007 Cree, Inc.-----in this document is subject100 PA Cree logo are registered trademarks of Cree, Inc. CLD-CT128.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color 1: Full-color distribution 2~9, A~Z . . . : special request * aaaaaaaaa-aaa-aa- x x x x x IV 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type 0: Standard = tube pack 1~9, A~Z . . . : special request * Product P/N * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number Description LP476PWN1-90G-00001 P4 90 White, FULL RANK, Tube Pack LP476PWN1-90G-00002 P4 90 White\, A1, A2, B1, B2, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT128.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps