LTC3251/ LTC3251-1.2/LTC3251-1.5 500mA High Efficiency, Low Noise, Inductorless Step-Down DC/DC Converter DESCRIPTIO U FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Up to 500mA Output Current No Inductors 2.7V to 5.5V Input Voltage Range 2x Efficiency Improvement Over LDOs 2-Phase, Spread Spectrum Operation for Low Input and Output Noise Shutdown Disconnects Load from VIN Adjustable Output Voltage Range: 0.9V to 1.6V Fixed Output Voltages: 1.2V, 1.5V Super Burst, Burst and Burst Defeat Operating Modes Low Operating Current: IIN = 35µA (Burst Mode® Operation) Super Burst Operating Current: IIN = 10µA Low Shutdown Current: IIN = 0.01µA Typ Soft-Start Limits Inrush Current at Turn-On Short-Circuit and Overtemperature Protected Available in a Thermally Enhanced 10-Pin MSOP Package U APPLICATIO S ■ ■ ■ Handheld Devices Cellular Phones Portable Electronic Equipment DSP Power Supplies A unique 2-phase spread spectrum architecture provides a very low noise regulated output as well as low noise at the input.* The parts have four operating modes: Continuous Spread Spectrum, Spread Spectrum with Burst Mode operation, Super BurstTM mode operation and shutdown. Low operating current (35µA in Burst Mode operation, 10µA in Super Burst mode operation) and low external parts count make the LTC3251/LTC3251-1.2/LTC3251-1.5 ideally suited for space-constrained battery-powered applications. The parts are short-circuit and overtemperature protected, and are available in a thermally enhanced 10-pin MSOP package. , LTC and LT are registered trademarks of Linear Technology Corporation. Burst Mode is a registered trademark of Linear Technology Coareoration. Super Burst is a trademark of Linear Technology Corporation. *U.S. Patent #6, 411, 531 U ■ The LTC®3251/LTC3251-1.2/LTC3251-1.5 are 2-phase charge pump step-down DC/DC converters that produce a regulated output from a 2.7V to 5.5V input. The parts use switched capacitor fractional conversion to achieve twice the typical efficiency of a linear regulator. No inductors are required. VOUT is resistor programmable from 0.9V to 1.6V or fixed at 1.2V or 1.5V, with up to 500mA of load current available. 1.5V Efficiency vs Input Voltage (Burst Mode Operation) TYPICAL APPLICATIO 100 Spread Spectrum Step-Down Converter LTC3251-1.5 2 7 VIN VOUT 3 8 C1+ C2+ 1µF 4 6 C2– C1– 5, 11 10 GND MODE VOUT = 1.5V 500mA 10µF 1µF EFFICIENCY (%) 1 9 MD0 MD1 1µF LTC3251-1.5 80 OFF ON 1-CELL Li-Ion OR 3-CELL NiMH IOUT = 200mA 90 70 60 50 LDO 40 30 20 10 3251 TA01 0 3 3.5 4.5 4 INPUT VOLTAGE (V) 5 5.5 3251 TA02 32511215fa 1 LTC3251/ LTC3251-1.2/LTC3251-1.5 W W W AXI U U ABSOLUTE RATI GS (Notes 1, 7) VIN to GND ................................................... –0.3V to 6V MD0, MD1, MODE and FB to GND . – 0.3V to (VIN + 0.3V) IOUT (Note 2) ...................................................... 650mA Operating Temperature Range (Note 3) ... –40°C to 85°C Storage Temperature Range .................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................... 300°C U U W PACKAGE/ORDER I FOR ATIO TOP VIEW MD0 VIN C1 + C1– GND 1 2 3 4 5 11 10 9 8 7 6 FB MD1 C2+ VOUT C2– MSE PACKAGE 10-LEAD PLASTIC MSOP EXPOSED PAD IS GND (PIN 11), MUST BE SOLDERED TO PCB TJMAX = 125°C, θJA = 40°C/W, θJC = 10°C/W ORDER PART NUMBER LTC3251EMSE 1 2 3 4 5 11 10 9 8 7 6 MODE MD1 C2+ VOUT C2– LTC3251EMSE-1.2 LTC3251EMSE-1.5 MSE PACKAGE 10-LEAD PLASTIC MSOP MSE PART MARKING LTB4 ORDER PART NUMBER TOP VIEW MD0 VIN C1 + C1– GND EXPOSED PAD IS GND (PIN 11), MUST BE SOLDERED TO PCB TJMAX = 125°C, θJA = 40°C/W, θJC = 10°C/W MSE PART MARKING LTAGM LTABE Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 3.6V, C1 = C2 = 1µF, CIN = 1µF, COUT = 10µF, VMODE = 0V for LTC3251-1.2V or LTC3251-1.5, VOUT = 1.5V for LTC3251, all capacitors ceramic, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX 2.7 UNITS VIN Minimum Operating Voltage (Notes 4,5) ● VIN Maximum Operating Voltage (Note 5) ● V VIN Continuous Mode Operating Current IOUT = 0mA, VMD0 = 0, VMD1 = VIN Spread Spectrum Disabled MODE = VIN ● ● 3 3.75 5 6 mA mA VIN Burst Mode Operating Current IOUT = 0mA, VMD0 = VIN, VMD1 = 0 Spread Spectrum Disabled MODE = VIN ● ● 35 35 60 60 µA µA VIN Super Burst Mode Operating Current IOUT = 0mA, VMD0 = VIN, VMD1 = VIN Spread Spectrum Disabled MODE = VIN ● ● 10 10 15 15 µA µA VIN Shutdown Current VMD0 = 0V, VMD1 = 0V (Note 5) ● 0.01 1 µA VFB Regulation Voltage (LTC3251) IOUT = 0mA, 2.7V ≤ VIN ≤ 5.5V ● 0.78 0.8 0.82 V VOUT Regulation Voltage (LTC3251-1.2) Continuous Mode or Burst Mode Operation IOUT ≤ 200mA, 2.7V ≤ VIN ≤ 5.5V (Note 5) IOUT ≤ 300mA, 2.8V ≤ VIN ≤ 5.5V (Note 5) IOUT ≤ 500mA, 3V ≤ VIN ≤ 5.5V (Note 5) ● ● 1.15 1.15 1.15 1.2 1.2 1.2 1.25 1.25 1.25 V V V VOUT Regulation Voltage (LTC3251-1.2) Super Burst Operation IOUT ≤ 40mA ● 1.15 1.2 1.25 V VOUT Regulation Voltage (LTC3251-1.5) Continuous Mode or Burst Mode Operation IOUT ≤ 100mA, 3.1V ≤ VIN ≤ 5.5V (Note 5) IOUT ≤ 200mA, 3.2V ≤ VIN ≤ 5.5V (Note 5) IOUT ≤ 300mA, 3.3V ≤ VIN ≤ 5.5V (Note 5) IOUT ≤ 500mA, 3.5V ≤ VIN ≤ 5.5V (Note 5) ● ● ● 1.44 1.44 1.44 1.44 1.5 1.5 1.5 1.5 1.56 1.56 1.56 1.56 V V V V VOUT Regulation Voltage (LTC3251-1.5) Super Burst Operation IOUT ≤ 40mA ● 1.44 1.5 1.56 V IOUT Continuous Output Current (LTC3251) VMD0 = 0, VMD1 = VIN or VMD0 = VIN, VMD1 = 0 ● 500 IOUT Super Burst Output Current (LTC3251) VMD0 = VIN, VMD1 = VIN ● 40 Load Regulation (LTC3251) 0mA ≤ IOUT ≤ 500mA, Referred to FB Pin 5.5 V mA mA 0.045 mV/mA 32511215fa 2 LTC3251/ LTC3251-1.2/LTC3251-1.5 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 3.6V, C1 = C2 = 1µF, CIN = 1µF, COUT = 10µF, VMODE = 0V for LTC3251-1.2V or LTC3251-1.5, VOUT = 1.5V for LTC3251, all capacitors ceramic, unless otherwise noted. PARAMETER CONDITIONS Line Regulation (LTC3251) IOUT = 500mA, 2.7V ≤ VIN ≤ 5.5V MIN Spread Spectrum Frequency Range fMIN Switching Frequency fMAX Switching Frequency ● ● 0.7 Spread Spectrum Disabled Frequency MODE = VIN ● 1.3 MD0, MD1 Input High Voltage 2.7V ≤ VIN ≤ 5.5V ● MD0, MD1 Input Low Voltage 2.7V ≤ VIN ≤ 5.5V ● 0.4 MD0, MD1 Input High Current MD0 = VIN, MD1 = VIN ● –1 MD0, MD1 Input Low Current MD0 = 0V, MD1 = 0V ● FB Input Current (LTC3251) VFB = 0.85V ● MODE Input High Voltage (LTC3251-1.2/LTC3251-1.5) 2.7V ≤ VIN ≤ 5.5V ● MODE Input Low Voltage (LTC3251-1.2/LTC3251-1.5) 2.7V ≤ VIN ≤ 5.5V ● 30 MODE Input High Current (LTC3251-1.2/LTC3251-1.5) MODE = VIN ● –1 1 µA MODE Input Low Current (LTC3251-1.2/LTC3251-1.5) MODE = 0V ● –1 1 µA Turn-On Time (Burst or Continuous Mode Operation) ROL = 3Ω, (Note 5) Open-Loop Output Impedance (LTC3251) VIN = 3V, IOUT = 200mA (Note 6) Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: Based on long term current density limitations. Note 3: The LTC3251E is guaranteed to meet specified performance from 0°C to 70°C. Specifications over the – 40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 4: Minimum operating voltage required for regulation is: VIN ≥ 2 • (VOUT + ROL • IOUT) TYP MAX UNITS 0.2 %/V 1.0 1.6 2 MHz MHZ 1.6 2 MHz 0.8 1.2 V 0.8 V 1 µA –1 1 µA –50 50 nA 70 %/VIN 50 50 %/VIN 1 ms 0.45 ● Ω 0.7 Note 5: VMODE = 0V or VMODE = VIN for LTC3251-1.2/LTC3251-1.5. Note 6: Output not in regulation; ROL = (VIN/2 – VOUT)/IOUT. (VFB = 0.76V). Burst or continuous mode operation. Note 7: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. U W TYPICAL PERFOR A CE CHARACTERISTICS No Load Supply Current vs Supply Voltage (Continuous Mode Spread Spectrum Enabled) 6 10 –40°C 25°C 85°C 9 8 50 –40°C 25°C 85°C 45 85°C 7 ICC (mA) IIN (mA) 5 4 3 40 6 5 –40°C 30 2 1 25°C 35 4 3 2 0 2.7 No Load Supply Current vs Supply Voltage (Burst Mode Operation) IIN (µA) 7 No Load Supply Current vs Supply Voltage (Continuous Mode, Spread Spectrum Disabled) 25 1 3.2 3.7 4.2 VIN (V) 4.7 5.2 3251 G01 0 2.7 3.2 3.7 4.2 VIN (V) 4.7 5.2 3251 G17 20 2.7 3.2 3.7 4.2 VIN (V) 4.7 5.2 3251 G02 32511215fa 3 LTC3251/ LTC3251-1.2/LTC3251-1.5 U W TYPICAL PERFOR A CE CHARACTERISTICS 1.5V Output Voltage vs Supply Voltage (Burst Mode Operation/ Continuous Mode) 1.60 18 1.58 16 1.56 14 1.54 12 85°C 10 25°C 8 –40°C 1.300 TA = 25°C 1.260 1.240 IOUT = 0mA 1.52 IOUT = 250mA 1.50 1.48 IOUT = 500mA 1.44 1.140 2 1.42 1.120 4.7 1.40 5.2 3.5 3 4 4.5 VIN (V) 5 5.5 3251 G02 0mA 10mA 40mA 1.56 1.28 1.24 1.52 1.22 VOUT (V) 1.54 1.48 1.44 1.14 1.42 1.12 3.5 4 4.5 VIN (V) 5 0mA 10mA 40mA 3251 G05 0.805 TA = 25°C VOUT = 1.5V 0.785 3.2 3.7 4.2 VIN (V) 4.7 0.780 5.2 40 80 80 70 70 VIN = 3.5V 60 50 VIN = 4.5V 40 20 20 10 10 10 1 10 IOUT (mA) 100 1000 3251 G08 0 100 1000 VIN = 4V VIN = 5V 40 20 0.1 VIN = 3.3V 50 30 MD0 = VIN, MD1 = 0V 0 0.1 10 1 IOUT (mA) 600 60 30 MD0 = VIN, MD1 = 0V 500 VIN = 3.6V 90 VIN = 2.7V 30 0 300 400 IOUT (mA) 100 VIN = 3V EFFICIENCY (%) EFFICIENCY (%) 90 VIN = 5V 50 200 1.5V Output Efficiency vs Output Current (Super Burst Mode Operation) 1.2V Output Efficiency vs Output Current (Burst Mode Operation) VIN = 3.6V VIN = 4V 60 100 3251 G07 100 80 0 3251 G18 100 70 5.2 0.790 1.10 2.7 5.5 1.5V Output Efficiency vs Output Current (Burst Mode Operation) VIN = 3.3V 4.7 0.795 3251 G06 90 4.2 VIN (V) 0.800 1.18 1.16 3 3.7 FB Voltage vs Output Current (Burst Mode Operation/ Continuous Mode) 1.20 1.46 1.40 TA = 25°C 1.26 1.50 3.2 VFB (V) TA = 25°C 1.58 1.100 2.7 1.2V Output Voltage vs Supply Voltage (Super Burst Mode Operation) 1.30 1.60 IOUT = 500mA 3251 G04 1.5V Output Voltage vs Supply Voltage (Super Burst Mode Operation) VOUT (V) 1.180 4 4.2 VIN (V) IOUT = 0mA 1.200 1.160 3.7 IOUT = 250mA 1.220 1.46 3.2 TA = 25°C 1.280 6 0 2.7 EFFICIENCY (%) 1.2V Output Voltage vs Supply Voltage (Burst Mode Operation/ Continuous Mode) VOUT (V) 20 VOUT (V) ICC (µA) No Load Supply Current vs Supply Voltage (Super Burst Mode Operation) MD0 = MD1 = VIN 0.1 10 1 100 IOUT (mA) 3251 G19 3251 G09 32511215fa 4 LTC3251/ LTC3251-1.2/LTC3251-1.5 U W TYPICAL PERFOR A CE CHARACTERISTICS MD0/MD1 Input Threshold Voltage vs Supply Voltage Max/Min Oscillator Frequency vs Supply Voltage 1.2 2.0 1.9 1.8 1.0 –40°C MAX 1.7 FREQUENCY (MHz) MD0/MD1 THRESHOLD (V) 1.1 –40°C 0.9 25°C 0.8 85°C 0.7 0.6 25°C MAX 1.6 85°C MAX 1.5 1.4 1.3 1.2 25°C MIN 1.1 –40°C MIN 1.0 0.5 85°C MIN 0.9 0.4 2.7 3.2 3.7 4.2 VIN (V) 4.7 0.8 5.2 2.7 3.2 3.7 4.2 VIN (V) 4.7 3251 G11 3251 G10 Output Transient Response (Burst Mode Operation) Output Transient Response (Continuous Mode) IOUT 450mA IOUT 450mA 50mA 50mA VOUT 20mV/DIV (AC) VOUT 20mV/DIV (AC) TA = 25°C 10µs/DIV COUT = 10µF X5R 6.3V VOUT = 1.5V VIN VOUT 20mV/DIV (AC) 10µs/DIV TA = 25°C COUT = 10µF X5R 6.3V VOUT = 1.5V 3251 G13 3251 G14 LTC3251-1.5 Output Voltage Ripple Supply Transient Response (Continuous Mode) VIN 5.2 4.5V SPREAD SPECT ENABLED 10mV/DIV (AC) 3.5V VOUT 20mV/DIV (AC) SPREAD SPECT DISABLED 10mV/DIV (AC) 20µs/DIV TA = 25°C COUT = 10µF X5R 6.3V IOUT = 250mA VOUT = 1.5V 3251 G15 200ns/DIV TA = 25°C COUT = 10µF X5R 6.3V IOUT = 500mA VOUT = 1.5V 3251 G16 32511215fa 5 LTC3251/ LTC3251-1.2/LTC3251-1.5 U U U PI FU CTIO S MD0 (Pin 1)/MD1 (Pin 9): Switching Mode Input Pins. The Mode input pins are used to set the operating mode of the LTC3251. The modes of operation are: MD1 MD0 OPERATING MODE 0 0 Shutdown 0 1 Spread Spectrum with Burst 1 0 Continuous Spread Spectrum 1 1 Super Burst MD0 and MD1 are high impedance CMOS inputs and must not be allowed to float. VIN (Pin 2): Input Supply Voltage. Operating VIN may be between 2.7V and 5.5V. Bypass VIN with a ≥ 1µF low ESR ceramic capacitor to GND (COUT). C1+ (Pin 3): Flying Capacitor 1 Positive Terminal (C1). C1– (Pin 4): Flying Capacitor 1 Negative Terminal (C1). GND (Pin 5, 11): Ground. Connect to a ground plane for best performance. C2 – (Pin 6): Flying Capacitor 2 Negative Terminal (C2). VOUT (Pin 7): Regulated Output Voltage. VOUT is disconnected from VIN during shutdown. Bypass VOUT with a low ESR ceramic capacitor to GND (CIN). See VOUT Capacitor Selection for capacitor size requirements. C2 + (Pin 8): Flying Capacitor 2 Positive Terminal (C2). FB (Pin 10) (LTC3251): Feedback Input Pin. An output divider should be connected from VOUT to FB to program the output voltage. MODE (Pin 10) (LTC3251-1.2/LTC3251-1.5): Spread Spectrum Operation Mode Pin. A low voltage on MODE enables spread spectrum operation. When MODE is high spread spectrum operation is disabled and switching occurs at the maximum operating frequency. 32511215fa 6 LTC3251/ LTC3251-1.2/LTC3251-1.5 W W SI PLIFIED BLOCK DIAGRA LTC3251-1.2/ LTC3251-1.5 ONLY 1 10 9 MD0 MODE MD1 OVERTEMP SWITCH CONTROL AND SOFT-START CHARGE PUMP 1 VIN C1+ C1– VOUT CHARGE PUMP 2 C2+ C2– FB – 3 4 INTERNAL ON LTC3251-1.2/ LTC3251-1.5 7 8 6 10 BURST DETECT CIRCUIT + 2 SPREAD SPECTRUM OSCILLATOR GND 5 11 3251 BD 32511215fa 7 LTC3251/ LTC3251-1.2/LTC3251-1.5 U OPERATIO (Refer to Block Diagram) The LTC3251 family of parts use a dual phase switched capacitor charge pump to step down VIN to a regulated output voltage. Regulation is achieved by sensing the output voltage through an external resistor divider and modulating the charge pump output current based on the error signal. A 2-phase nonoverlapping clock activates the two charge pumps. The two charge pumps work in parallel, but out of phase from each other. On the first phase of the clock, current is transferred from VIN, through the external flying capacitor 1, to VOUT via the switches of Charge Pump 1. Not only is current being delivered to VOUT on the first phase, but the flying capacitor is also being charged. On the second phase of the clock, flying capacitor 1 is connected from VOUT to ground, transferring the charge stored during the first phase of the clock to VOUT via the switches of Charge Pump 1. Charge Pump 2 operates in the same manner, but with the phases of the clock reversed. This dual phase architecture achieves extremely low output and input noise by providing constant charge transfer from VIN to VOUT. Using this method of switching, only half of the output current is delivered from VIN, thus achieving twice the efficiency over a conventional LDO. A spread spectrum oscillator, which utilizes random switching frequencies between 1MHz and 1.6MHz, sets the rate of charging and discharging of the flying capacitors. The LTC3251-1.2/ LTC3251-1.5 MODE pin can be used to disable spread spectrum operation which causes switching to occur at 1.6MHz. The part also has two types of low current Burst Mode operation to improve efficiency even at light loads. In shutdown mode, all circuitry is turned off and the LTC3251 family draws only leakage current from the VIN supply. Furthermore, VOUT is disconnected from VIN. The MD0 and MD1 pins are CMOS inputs with threshold voltages of approximately 0.8V to allow regulator control with low voltage logic levels. The MODE pin is also CMOS, but has a threshold of about 1/2 • VIN. The LTC3251 family is in shutdown when a logic low is applied to both mode pins. Since MD0, MD1 and MODE pins are high impedance CMOS inputs, they should never be allowed to float. Always drive MD0, MD1 and Mode with valid logic levels. Short-Circuit/Thermal Protection The LTC3251 family has built-in short-circuit current limiting as well as overtemperature protection. During short-circuit conditions, internal circuitry automatically limits the output current to approximately 800mA. At higher temperatures, or in cases where internal power dissipation causes excessive self heating on chip (i.e., output short circuit), the thermal shutdown circuitry will shut down the charge pumps when the junction temperature exceeds approximately 160°C. It will re-enable the charge pumps once the junction temperature drops back to approximately 150°C. The LTC3251 will cycle in and out of thermal shutdown without latch-up or damage until the overstress condition is removed. Long term overstress (IOUT > 650mA and/or TJ > 125°C) should be avoided as it can degrade the performance or shorten the life of the part. Soft-Start To prevent excessive current flow at VIN during start-up, the LTC3251 family has built-in soft-start circuitry. Softstart is achieved by increasing the amount of current available to the output charge storage capacitor linearly over a period of approximately 500µs. Soft-start is enabled whenever the device is brought out of shutdown, and is disabled shortly after regulation is achieved. Spread Spectrum Operation Switching regulators can be particularly troublesome where electromagnetic interference (EMI) is concerned. Switching regulators operate on a cycle-by-cycle basis to transfer power to an output. In most cases the frequency of operation is either fixed or is a constant based on the output load. This method of conversion creates large components of noise at the frequency of operation (fundamental) and multiples of the operating frequency (harmonics). Figure 1a shows a conventional buck switching converter. Figures 1b and 1c are the input and output noise spectrums for the buck converter of Figure 1 with VIN = 3.6V, VOUT = 1.5V and IOUT = 500mA. 32511215fa 8 LTC3251/ LTC3251-1.2/LTC3251-1.5 U OPERATIO (Refer to Block Diagram) 4.7µH IN VIN 10nH* 10nH* SW VOUT 10µF 22µF IN VIN 1µF 1µF FB COMP GND *10nH = 1cm OF PCB TRACE 1µF –40 –40 –50 –50 –60 –70 –80 C2 – GND 1µF *10nH = 1cm OF PCB TRACE 3251 F02a –60 –70 –80 –90 –90 START FREQ: 100kHz RBW: 10kHz STOP FREQ: 30MHz START FREQ: 100kHz RBW: 10kHz STOP FREQ: 30MHz 3251 F01b 3251 F02b Figure 1b. Conventional Buck Converter Output Noise Spectrum with 22µF Output Capacitor (IO = 500mA) Figure 2b. LTC3251 Output Noise Spectrum with 10µF Output Capacitor (IO = 500mA) –40 –40 –50 –50 NOISE (dBm) NOISE (dBm) C1– FB C2 + 1µF Figure 2a. LTC3251 Buck Converter NOISE (dBm) NOISE (dBm) Figure 1a. Conventional Buck Switching Converter VOUT 10µF LTC3251 C1+ 3251 F01a OUT –60 –70 –80 –60 –70 –80 –90 START FREQ: 100kHz RBW: 10kHz STOP FREQ: 30MHz 3251 F01c –90 START FREQ: 100kHz RBW: 10kHz STOP FREQ: 30MHz 3251 F02c Figure 1c. Conventional Buck Converter Input Noise Spectrum with 10µF Input Capacitor (IO = 500mA) Unlike conventional buck converters, the LTC3251’s internal oscillator is designed to produce a clock pulse whose period is random on a cycle-by-cycle basis, but fixed between 1MHz and 1.6MHz. This has the benefit of spreading the switching noise over a range of frequencies, thus significantly reducing the peak noise. Figures 2b and 2c are the input and output noise spectrums for the LTC3251 of Figure 2a with VIN = 3.6V, VOUT = 1.5V and IOUT = 500mA. Note the significant reduction in peak output noise (>20dBm) with only 1/2 the output capacitance and the virtual elimination of input harmonics with only 1/10 the input capacitance. Spread spectrum operation is used exclusively in “continuous” mode and for output currents greater than about 50mA in Burst Mode operation. Figure 2c. LTC3251 Input Noise Spectrum with 1µF Input Capacitor (IO = 500mA) Low Current Burst Mode Operation To improve efficiency at low output currents, a Burst Mode function is included in the LTC3251 family of parts. An output current sense is used to detect when the required output current drops below an internally set threshold (50mA typ). When this occurs, the part shuts down the internal oscillator and goes into a low current operating state. The part will remain in the low current operating state until the output voltage has dropped enough to require another burst of current. When the output current exceeds 50mA, the part will operate in continuous mode. Unlike traditional charge pumps, where the burst current is dependant on many factors (i.e., supply, switch strength, 32511215fa 9 LTC3251/ LTC3251-1.2/LTC3251-1.5 U OPERATIO (Refer to Block Diagram) Ultralow Current Super Burst Mode Operation To further optimize the supply current for low output current requirements, a Super Burst mode operaton is included in the LTC3251 family of parts. This mode is very similar to Burst Mode operation, but much of the internal circuitry and switch is shut down to further reduce supply current. In Super Burst mode operation an internal hysteretic comparator is used to enable/disable charge transfer. The hysteresis of the comparator and the amount of current deliverable to the output are limited to keep output ripple low. The VOUT ripple voltage in Super Burst mode operation is typically 35mV with a 10µF output capacitor. The LTC3251 family can deliver 40mA of current in Super Burst mode operation but does not switch to continuous mode. The MODE pin of the LTC3251-1.2 and LTC32511.5 has no effect on operation in super-burst mode. Diagram, the LTC3251 family uses a control loop to adjust the strength of the charge pump to match the current required at the output. The error signal of this loop is stored directly on the output charge storage capacitor. Thus the charge storage capacitor also serves to form the dominant pole for the control loop. The desired output voltage also affects stability. As the divider ratio (RA/RB) drops, the effective closed-loop gain increases, thus requiring a larger output capacitor for stability. Figure 3 shows the suggested output capacitor for optimal transient response. The value of the output capacitance should not drop below the minimum capacitance line to prevent excessive ringing or instability. (see Ceramic Capacitor Selection Guidelines section). 16 15 14 OPTIMUM CAPACITANCE 13 12 COUT (µF) capacitor selection, etc.), the part’s burst current is set by the burst threshold and hysteresis. This means that the VOUT ripple voltage in Burst Mode operation will be fixed and is typically 15mV with a 10µF output capacitor. 11 10 9 8 VOUT Capacitor Selection The style and value of capacitors used with the LTC3251 family determine several important parameters such as regulator control loop stability, output ripple and charge pump strength. The dual phase nature of the LTC3251 family minimizes output noise significantly but not completely. What small ripple that does exist is controlled by the value of COUT directly. Increasing the size of COUT will proportionately reduce the output ripple. The ESR (equivalent series resistance) of COUT plays the dominant role in output noise. When a part switches between clock phases there is a period where all switches are turned off. This “blanking period” shows up as a spike at the output and is a direct function of the output current times the ESR value. To reduce output noise and ripple, it is suggested that a low ESR (<0.08Ω) ceramic capacitor be used for COUT. Tantalum and aluminum capacitors are not recommended because of their high ESR. Both the style and value of COUT can significantly affect the stability of the LTC3251 family. As shown in the Block MINIMUM CAPACITANCE 7 6 5 4 0.9 1.0 1.1 1.2 1.3 VOUT (V) 1.4 1.5 1.6 3251 F03 Figure 3 Likewise excessive ESR on the output capacitor will tend to degrade the loop stability. The closed loop output impedance of the LTC3251 is approximately: RO = 0.045Ω • VOUT 0.8 V For example, with the output programmed to 1.5V, the RO is 0.085Ω, which produces a 40mV output change for a 500mA load current step. For stability and good load transient response, it is important for the output capacitor to have 0.08Ω or less of ESR. Ceramic capacitors typically have exceptional ESR, and combined with a tight board layout, should yield excellent stability and load transient performance. 32511215fa 10 LTC3251/ LTC3251-1.2/LTC3251-1.5 U OPERATIO (Refer to Block Diagram) Further output noise reduction can be achieved by filtering the LTC3251 output through a very small series inductor as shown in Figure 4. A 10nH inductor will reject the fast output transients caused by the blanking period. The 10nH inductor can be fabricated on the PC board with about 1cm (0.4") of 1mm wide PC board trace. 10nH (TRACE INDUCTANCE) VOUT LTC3251 GND VOUT 10µF 1µF 3251 F04 Figure 4. 10nH Inductor Used for Additional Output Noise Reduction VIN Capacitor Selection The dual phase architecture used by the LTC3251 family makes input noise filtering much less demanding than conventional charge pump regulators. The input current should be continuous at about IOUT/2. The blanking period described in the VOUT section also effects the input. For this reason it is recommended that a low ESR, 1µF (0.4µF min) or greater ceramic capacitor be used for CIN (see Ceramic Capacitor Selection Guidelines section). In cases where the supply impedance is high, heavy output transients can cause significant input transients. These input transients feed back to the output which slows the output transient recovery and increases overshoot and output impedance. This effect can generally be avoided by using low impedance supplies and short supply connections. If this is not possible, a ≥4.7µF capacitor is recommended for the input capacitor. Aluminum and tantalum capacitors are not recommended because of their high ESR. Further input noise reduction can be achieved by filtering the input through a very small series inductor as shown in Figure 5. A 10nH inductor will reject the fast input transients caused by the blanking period, thereby presenting a nearly constant load to the input supply. For economy, the 10nH inductor can be fabricated on the PC board with about 1cm (0.4") of 1mm wide PC board trace. VIN SUPPLY 10nH (TRACE INDUCTANCE) VIN 1µF LTC3251 GND 3251 F05 Figure 5. 10nH Inductor Used for Additional Input Noise Reduction Flying Capacitor Selection Warning: A polarized capacitor such as tantalum or aluminum should never be used for the flying capacitors since their voltages can reverse upon start-up of the LTC3251. Ceramic capacitors should always be used for the flying capacitors. The flying capacitors control the strength of the charge pump. In order to achieve the rated output current, it is necessary for the flying capacitor to have at least 0.4µF of capacitance over operating temperature with a 2V bias (see Ceramic Capacitor Selection Guidelines). If only 200mA or less of output current is required for the application, the flying capacitor minimum can be reduced to 0.15µF. Ceramic Capacitor Selection Guidelines Capacitors of different materials lose their capacitance with higher temperature and voltage at different rates. For example, a ceramic capacitor made of X5R or X7R material will retain most of its capacitance from – 40°C to 85°C, whereas a Z5U or Y5V style capacitor will lose considerable capacitance over that range (60% to 80% loss typ). Z5U and Y5V capacitors may also have a very strong voltage coefficient, causing them to lose an additional 60% or more of their capacitance when the rated voltage is applied. Therefore, when comparing different capacitors, it is often more appropriate to compare the amount of achievable capacitance for a given case size rather than discussing the specified capacitance value. For example, over rated voltage and temperature conditions, a 4.7µF, 10V, Y5V ceramic capacitor in an 0805 case may not provide any more capacitance than a 1µF, 10V, X5R or X7R available in the same 0805 case. In fact, over bias and 32511215fa 11 LTC3251/ LTC3251-1.2/LTC3251-1.5 U OPERATIO (Refer to Block Diagram) temperature range, the 1µF, 10V, X5R or X7R will provide more capacitance than the 4.7µF, 10V, Y5V. The capacitor manufacturer’s data sheet should be consulted to determine what value of capacitor is needed to ensure minimum capacitance values are met over operating temperature and bias voltage. Below is a list of ceramic capacitor manufacturers and how to contact them: AVX www.avxcorp.com Kemet www.kemet.com Murata www.murata.com Taiyo Yuden www.t-yuden.com TDK www.tdk.com Thermal Management Layout Considerations Due to the high switching frequency and transient currents produced by the LTC3251, careful board layout is necessary for optimal performance. A true ground plane and short connections to all capacitors will improve performance and ensure proper regulation under all conditions. Figure 6 shows the recommended layout configuration. CI 1µF LTC3251 COMPONENTS NOT USED ON THE LTC3251-1.2 OR LTC3251-1.5 RB VIN RA C1 1µF CA 5pF VOUT C2 1µF GND CO 10µF 3251 F06 The flying capacitor pins C1+, C1–, C2+, C2– will have very high edge rate wave forms. The large dv/dt on these pins can couple energy capacitively to adjacent printed circuit board runs. Magnetic fields can also be generated if the flying capacitors are not close to the part (i.e., the loop area is large). To decouple capacitive energy transfer, a Faraday shield may be used. This is a grounded PC trace between the sensitive node and the IC’s pins. For a high quality AC ground, it should be returned to a solid ground plane that extends all the way to the part. Keep the FB trace of the LTC3251 away from or shielded from the flying capacitor traces or degraded performance could result. If the junction temperature increases above approximately 160°C, the thermal shutdown circuitry will automatically deactivate the output. To reduce the maximum junction temperature, a good thermal connection to the PC board is recommended. Connecting the 10-pin MSE paddle directly to a ground plane, and maintaining a solid ground plane under the device on one or more layers of the PC board, can reduce the thermal resistance of the package and PC board considerably. Using this method a θJA of 40°C/W should be achieved. Power Efficiency The power efficiency (η) of the LTC3251 family is approximately double that of a conventional linear regulator. This occurs because the input current for a 2-to-1 step-down charge pump is approximately half the output current. For an ideal 2-to-1 step-down charge pump the power efficiency is given by: η≡ POUT VOUT • IOUT 2VOUT = = PIN VIN 1 VIN • IOUT 2 Figure 6. Recommended Layout 32511215fa 12 LTC3251/ LTC3251-1.2/LTC3251-1.5 U OPERATIO (Refer to Block Diagram) At moderate to high output power the switching losses and quiescent current of the LTC3251 family is negligible and the expression above is valid. For example with VIN = 3.6V, IOUT = 200mA and VOUT regulating to 1.5V the measured efficiency is 81% which is in close agreement with the theoretical 83.3% calculation. For a 1.5V output, RO is 0.085Ω, which produces a 40mV output change for a 500mA load current step. Thus, the user may want to target an unloaded output voltage slightly higher than desired to compensate for the output load conditions. The output may be programmed for regulation voltages of 0.9V to 1.6V. Programming the LTC3251 Output Voltage (FB Pin) Since the LTC3251 employs a 2-to-1 charge pump architecture, it is not possible to achieve output voltages greater than half the available input voltage. The minimum VIN supply required for regulation can be determined by the following equation: The LTC3251 is programmed to an arbitrary output voltage via an external resistive divider. Figure 7 shows the required voltage divider connection. The voltage divider ratio is given by the expression: V PD = IN – VOUT IOUT 2 VOUT LTC3251 VOUT CA RA COUT FB ( ) R 0.8V 1 + A RB RB GND VIN(MIN) ≤ 2 •␣ (VOUT(MIN) + IOUT • ROL) The compensation capacitor (CA) is necessary to counteract the pole caused by the large valued resistors RA and RB, and the input capacitance of the FB pin. For best results, CA should be 5pF for all RA or RB greater than 10k and can be omitted if both RA and RB are less than 10k. Disabling Spread Spectrum Operation on the LTC3251-1.2/LTC3251-1.5 (MODE Pin) 3251 F07 Spread spectrum operation can be disabled by driving MODE high. When Mode is high, switching takes place at the maximum operating frequency (typ 1.6MHz). The Typical values for total voltage divider resistance can range advantage of spread spectrum operation is that it reduces from several kΩs up to 1MΩ. the peak noise at and above the operating frequency at the The user may want to consider load regulation when setting expense of a slightly increased noise floor and slightly the desired output voltage. The closed loop output imped- increased low frequency ripple caused by the converter compensating for the changing operating frequency. Usance of the LTC3251 is approximately: ers who do not need the peak noise reduction gained by RA VOUT using spread spectrum may wish to disable spread spec= –1 0.8V RB trum, thus improving the low frequency input/output ripple. Figure 7. Programming the LTC3251 32511215fa 13 LTC3251/ LTC3251-1.2/LTC3251-1.5 U TYPICAL APPLICATIO S 0.9V Output Continuous/Burst Mode Operation with Shutdown OFF ON 1 9 MD0 MD1 LTC3251 7 VOUT VIN 3 8 1µF C1+ C2+ 1µF 4 6 C2– C1– 5,11 10 GND FB VOUT = 0.9V 500mA 2 1-CELL Li-Ion OR 3-CELL NiMH 10µF 1µF 4.7µF 5pF 73.2k 536k 3251 TA05 3.3V to 1.4V Conversion, Continuous Spread Spectrum Operation with Shutdown OFF ON 1 9 MD0 MD1 VIN 3.3V LTC3251 7 VIN VOUT 8 3 C1+ C2+ 6 4 C1– C2– 10 5,11 GND FB VOUT = 1.4V IOUT ≤ 350mA 2 1µF 1µF 10µF 1µF 4.12k 5.36k 3251 TA03 32511215fa 14 LTC3251/ LTC3251-1.2/LTC3251-1.5 U PACKAGE DESCRIPTIO MSE Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1663) BOTTOM VIEW OF EXPOSED PAD OPTION 2.794 ± 0.102 (.110 ± .004) 5.23 (.206) MIN 0.889 ± 0.127 (.035 ± .005) 1 2.06 ± 0.102 (.081 ± .004) 1.83 ± 0.102 (.072 ± .004) 2.083 ± 0.102 3.20 – 3.45 (.082 ± .004) (.126 – .136) 10 0.50 0.305 ± 0.038 (.0197) (.0120 ± .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 3.00 ± 0.102 (.118 ± .004) (NOTE 4) 4.90 ± 0.152 (.193 ± .006) 0.254 (.010) DETAIL “A” 0° – 6° TYP 1 2 3 4 5 GAUGE PLANE 0.53 ± 0.152 (.021 ± .006) DETAIL “A” 0.18 (.007) 0.497 ± 0.076 (.0196 ± .003) REF 10 9 8 7 6 SEATING PLANE 0.86 (.034) REF 1.10 (.043) MAX 0.17 – 0.27 (.007 – .011) TYP 0.50 (.0197) BSC 0.127 ± 0.076 (.005 ± .003) MSOP (MSE) 0603 NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 32511215fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC3251/ LTC3251-1.2/LTC3251-1.5 U TYPICAL APPLICATIO 1.2V Output with mProcessor Control of Operating Modes (Spread Spectrum Disabled) µP 1 9 MD0 MD1 LTC3251-1.2 7 VIN VOUT 3 8 C1+ C2+ 1µF 4 6 C2– C1– 5,11 10 GND MODE 2 1-CELL Li-Ion OR 3-CELL NiMH 1µF 1µF VOUT = 1.2V IOUT UP TO 300mA, VIN ≥ 2.8V 10µF I OUT UP TO 500mA, VIN ≥ 3.0V X5R 6.3V 3251 TA04 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1514 50mA, 650kHz, Step-Up/Down Charge Pump with Low Battery Comparator VIN: 2.7V to 10V, VOUT: 3V or 5V, Regulated Output, IQ: 60µA, ISD: 10µA, S8 Package LTC1515 50mA, 650kHz, Step-Up/Down Charge Pump with Power-On Reset VIN: 2.7V to 10V, VOUT: 3.3V or 5V, Regulated Output, IQ: 60µA, ISD: <1µA, S8 Package LT1776 500mA (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter 90% Efficiency, VIN: 7.4V to 40V, VOUT(MIN): 1.24V, IQ: 3.2mA, ISD: 30µA, N8, S8 Packages LTC1911-1.5/ LTC1911-1.8 250mA, 1.5MHz, High Efficiency Step-Down Charge Pump Up to 90% Efficiency, VIN: 2.7V to 5.5V, VOUT: 1.5V/1.8V, Regulated Output, IQ: 180µA, ISD: 10µA, MS8 Package LTC3250-1.5 250mA, 1.5MHz, High Efficiency Step-Down Charge Pump Up to 90% Efficiency, VIN: 3.1V to 5.5V, VOUT: 1.5V, Regulated Output, IQ: 35µA, ISD: <1µA, ThinSOT Package LTC3252 250mA, Dual, Low Noise, Inductorless Step-Down DC/DC Converter Up to 90% Efficiency, VIN: 2.7V to 5.5V, VOUT: 0.9V to 1.6V, IQ: 60µA, DFN Package LTC3404 600mA (IOUT), 1.4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.7V to 6V, VOUT(MIN): 0.8V, IQ: 10µA, ISD: <1µA, MS8 Package LTC3405/LTC3405A 300mA (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.7V to 6V, VOUT(MIN): 0.8V, IQ: 20µA, ISD: <1µA, ThinSOT Package LTC3406/LTC3406B 600mA (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN): 0.6V, IQ: 20µA, ISD: <1µA, ThinSOT Package LTC3411 1.25A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN): 0.8V, IQ: 60µA, ISD: <1µA, MS Package LTC3412 2.5A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN): 0.8V, IQ: 60µA, ISD: <1µA, TSSOP-16E Package LTC3440 600mA (IOUT), 2MHz, Synchronous Buck-Boost DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT: 2.5V to 5.5V, IQ: <25µA, ISD: 1µA, MS Package LTC3441 1.2A (IOUT), 1MHz, Synchronous Buck-Boost DC/DC Converter 95% Efficiency, VIN: 2.4V to 5.5V, VOUT: 2.4V to 5.25V, IQ: <25µA, ISD: 1µA, DFN Package 32511215fa 16 Linear Technology Corporation LT/TP 1203 1K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2003