19-3928; Rev 1; 4/06 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN Features The MAX5084/MAX5085 high-voltage linear regulators operate from an input voltage range of 6.5V to 65V and deliver up to 200mA of output current. These devices consume only 50µA (typ) of quiescent current with no load and 6µA (typ) in shutdown (EN pulled low). Both devices include a SET input, which when connected to ground, selects a preset output voltage of 5V (MAX5084) or 3.3V (MAX5085). Alternatively, the output voltage can be adjusted from 2.54V to 11V by connecting the SET pin to the regulator’s output through a resistive divider network. The MAX5084/ MAX5085 also include an OUT_SENSE pin, which allows remote voltage sensing right at the load, thus eliminating the voltage drop caused by the line impedance. Both devices are short-circuit protected and include thermal shutdown. The MAX5084/MAX5085 operate over the -40°C to +125°C automotive temperature range and are available in a space-saving 3mm x 3mm thermally enhanced 6-pin TDFN package. ♦ Wide Operating Input Voltage Range (6.5V to 65V) Applications ♦ Thermally Enhanced 3mm x 3mm 6-Pin TDFN Package Dissipates 1.905W at +70°C ♦ Guaranteed 200mA Output Current ♦ 50µA No-Load Supply Current ♦ Preset 3.3V, 5.0V, or Adjustable (from 2.54V to 11V) Output Voltage ♦ Remote Load Sense ♦ Thermal and Short-Circuit Protection ♦ -40°C to +125°C Operating Temperature Range ♦ SET Input for Adjustable Output Voltage ♦ Enable Input Ordering Information PART Automotive Industrial Home Security PINPACKAGE TOP MARK PKG CODE MAX5084ATT+T 6 TDFN-EP* AJI T633-2 MAX5085ATT+T 6 TDFN-EP* AJJ T633-2 Note: All devices are specified over the -40°C to +125°C operating temperature range. *EP = Exposed paddle. +Denotes lead-free package. Telecom/Networking Selector Guide appears at end of data sheet. Typical Operating Circuit VIN = 6.5V TO 65V Pin Configuration SET 10μF MAX5084 MAX5085 6 5 4 OUT_SENSE MAX5084 MAX5085 LOAD SET 1 IN + 2 3 GND GND EN EN OUT_SENSE OUT IN 10μF OUT TOP VIEW 5V (MAX5084) 3.3V (MAX5085) TDFN ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX5084/MAX5085 General Description MAX5084/MAX5085 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN ABSOLUTE MAXIMUM RATINGS IN to GND ...............................................................-0.3V to +80V EN to GND..............................................................-0.3V to +80V SET, OUT, OUT_SENSE to GND................-0.3V to the lesser of (VIN + 0.3V) or +13.2V OUT_SENSE to OUT..............................................-0.3V to +0.3V Short-Circuit Duration (VIN ≤ 65V) ..............................Continuous Maximum Current into Any Pin (except IN and OUT).......±20mA Continuous Power Dissipation (TA = +70°C) 6-Pin TDFN-EP (derate 23.8mW/°C above +70°C) ...1904.8mW* Thermal Resistance: θJA ................................................................................42°C/W θJC ...............................................................................8.5°C/W Operating Temperature Range .........................-40°C to +125°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C *As per JEDEC51 Standard (Multilayer Board). Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VIN = 14V, IOUT = 1mA, CIN = COUT = 10µF, VEN = 2.4V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical specifications are at TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER Input Voltage Range Supply Current SYMBOL VIN IQ CONDITIONS VIN > VOUT + 1.5V Measured at GND, SET = GND MIN 6.5 ISHDN MAX UNITS 65.0 V IOUT = 0 51 140 IOUT = 100µA 51 140 IOUT = 200mA Shutdown Supply Current TYP VEN ≤ 0.4V µA 2 4 mA 6 16 µA REGULATOR Guaranteed Output Current Output Voltage Accuracy IOUT VOUT Output Voltage Range Dropout Voltage ΔVDO Startup Response Time Line Regulation 2 ΔVOUT/ ΔVIN VOUT = VOUT(NOM) ±4% 200 mA VIN = 9V to 16V, SET = GND, IOUT = 5mA to 200mA, OUT_SENSE connected to OUT (MAX5084) 4.8 5.0 5.2 VIN = 6.5V to 21V, SET = GND, IOUT = 5mA to 100mA, OUT_SENSE connected to OUT (MAX5084) 4.85 5.0 5.15 VIN = 9V to 16V, SET = GND, IOUT = 5mA to 50mA, OUT_SENSE connected to OUT (MAX5084) 4.9 V VIN = 6.5V, SET = GND, IOUT = 1mA to 200mA, OUT_SENSE connected to OUT (MAX5085) 3.168 IOUT = 5mA, adjustable output 2.54 5.1 3.300 IOUT = 200mA, VOUT = 5V, MAX5084 (Note 2) 0.9 Rising edge of VIN to rising edge of VOUT, RL = 500Ω (Note 3) 400 VIN from 8V to 65V VIN from 14V to 65V 3.432 11.00 V 1.5 V µs MAX5084, SET = GND -1 +1 MAX5085, SET = GND -0.5 +0.5 Adjustable output from 2.54V to 11V -0.5 +0.5 _______________________________________________________________________________________ mV/V 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN (VIN = 14V, IOUT = 1mA, CIN = COUT = 10µF, VEN = 2.4V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical specifications are at TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL Enable Voltage VEN Enable Input Current IEN OUT to OUT_SENSE Internal Resistor ROUT_ SENSE CONDITIONS Regulator on MIN TYP MAX 2.4 Regulator off 0.4 VEN = 2.4V 0.5 1 VEN = 14V 4 8 VEN = 65V 14 35 8 15 24 IOUT_SENSE = 10mA UNITS V µA Ω SET Reference Voltage VSET IOUT = 10mA 1.220 1.251 1.280 V SET Input Leakage Current ISET VSET = 1.251V -100 +1 +100 nA MAX5084, SET = GND 0.3 1 MAX5085, SET = GND 0.3 1 Adjustable output from 2.54V to 11V 0.5 2 ΔVOUT/ ΔIOUT Load Regulation Power-Supply Rejection Ratio Short-Circuit Current PSRR ISC IOUT from 1mA to 200mA, OUT_SENSE = OUT IOUT = 10mA, f = 100Hz, VIN_RIPPLE = 500mVP-P, VOUT = 5V VIN = 8V to 14V VIN = 65V 55 220 340 mV/mA dB 500 mA 340 Thermal Shutdown TSHDN +160 °C Thermal Shutdown Hysteresis THYST 10 °C Note 1: Specifications at -40°C are guaranteed by design and not production tested. Note 2: Dropout voltage is defined as (VIN - VOUT) when VOUT is 100mV below the value of VOUT when VIN = VOUT + 3V. Note 3: Startup time measured from 50% of VIN to 90% of VOUT. _______________________________________________________________________________________ 3 MAX5084/MAX5085 ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (VIN = 14V, CIN = COUT = 10µF, VEN = VIN, TA = +25°C, unless otherwise noted.) NO-LOAD GROUND CURRENT vs. TEMPERATURE 90 70 3.5 60 IGND (μA) 4.0 3.0 2.5 2.0 1.0 0.5 IOUT = 0 8 50 40 VIN = 6.5V 6 5 4 3 20 2 10 1 0 0 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 -40 -25 -10 5 20 35 50 65 80 95 110 125 140 -40 -25 -10 5 20 35 50 65 80 95 110 125 140 VIN (V) TEMPERATURE (°C) TEMPERATURE (°C) OUTPUT VOLTAGE vs. TEMPERATURE GROUND CURRENT vs. TEMPERATURE OUTPUT VOLTAGE vs. LOAD CURRENT AND TEMPERATURE 5.15 2.00 1.75 IOUT = 1mA 5.10 5.25 5.20 5.15 IOUT = 200mA 5.10 IGND (μA) IOUT = 10mA 5.00 4.95 VOUT (V) 1.50 5.05 1.25 1.00 4.85 0.50 4.80 0.25 4.75 0 5.05 IOUT = 100mA IOUT = 50mA IOUT = 100mA 5.00 4.95 0.75 4.90 MAX5084 toc06 5.20 MAX5084 toc05 2.25 MAX5084 toc04 5.25 4.90 IOUT = 200mA 4.85 IOUT = 50mA 4.80 4.75 -40 -25 -10 5 20 35 50 65 80 95 110 125 140 -40 -25 -10 5 20 35 50 65 80 95 110 125 140 -40 -25 -10 5 20 35 50 65 80 95 110 125 140 TEMPERATURE (°C) TEMPERATURE (°C) TEMPERATURE (°C) DROPOUT VOLTAGE vs. LOAD CURRENT POWER-SUPPLY REJECTION RATIO vs. FREQUENCY LINE-TRANSIENT RESPONSE VOUT = 5V 1.35 1.20 IOUT = 10mA -10 1.05 PSRR (dB) 0.90 0.75 0.60 MAX5084 toc09 0 MAX5084 toc07 1.50 MAX5084 toc08 VOUT (V) 9 7 VIN = 14V 30 1.5 -20 IOUT 100mA/div -30 0A -40 VOUT 100mV/div AC-COUPLED -50 0.45 -60 0.30 -70 0.15 0 -80 10 30 50 70 90 110 130 150 170 190 IOUT (mA) 4 VIN = 65V 80 IGND (μA) 4.5 10 MAX5084 toc03 5.0 VOUT (V) 100 MAX5084 toc01 5.5 SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE MAX5084 toc03 OUTPUT VOLTAGE vs. INPUT VOLTAGE VDROPOUT (V) MAX5084/MAX5085 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN 0.1 1 10 100 1000 400μs/div FREQUENCY (kHz) _______________________________________________________________________________________ 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN INPUT VOLTAGE STEP RESPONSE STARTUP RESPONSE MAX5084 toc10 ENABLE STARTUP RESPONSE MAX5084 toc11 MAX5084 toc12 IOUT = 10mA VIN = 14V IOUT = 0 VIN 20V/div VEN 1V/div VOUT 2V/div 0V 0V 0V VOUT 500mV/div AC-COUPLED VOUT 2V/div VIN 50V/div 0V 400μs/div 0V 400μs/div ENABLE STARTUP RESPONSE 100μs/div ENABLE STARTUP RESPONSE MAX5084 toc13 ENABLE STARTUP RESPONSE MAX5084 toc14 VIN = 14V IOUT = 200mA MAX5084 toc15 VIN = 65V IOUT = 0 VIN = 65V IOUT = 200mA VEN 1V/div VEN 1V/div 0V VEN 1V/div 0V VOUT 2V/div VOUT 2V/div VOUT 2V/div 0V 0V 0V 100μs/div 100μs/div 100μs/div SHUTDOWN RESPONSE GROUND CURRENT DISTRIBUTION (TA = -40°C) GROUND CURRENT DISTRIBUTION (TA = +125°C) 10 36 UNITS TESTED VOUT 2V/div 54 UNITS TESTED 20 NUMBER OF UNITS 0V 8 NUMBER OF UNITS VEN 1V/div 25 MAX5084 toc17 MAX5084 toc16 VIN = 14V IOUT = 10mA 6 4 2 MAX5084 toc18 0V 15 10 5 0V 0 4ms/div 0 42 43 44 45 46 47 IGND (μA) 48 49 52 51 52 53 54 55 58 60 IGND (μA) _______________________________________________________________________________________ 5 MAX5084/MAX5085 Typical Operating Characteristics (continued) (VIN = 14V, CIN = COUT = 10µF, VEN = VIN, TA = +25°C, unless otherwise noted.) 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN MAX5084/MAX5085 Pin Description PIN NAME FUNCTION 1 IN Regulator Supply Input. Supply voltage ranges from 6.5V to 65V. Bypass with a 10µF capacitor to GND. 2 EN Enable Input. Force EN high to turn on the regulator. Pull EN low to place the device in a low-power shutdown mode. EN has an internal 5MΩ resistor to GND. 3 GND Ground 4 SET Feedback Input for Setting the Output Voltage. Connect SET to GND for a fixed 5V output (MAX5084), or 3.3V output (MAX5085). Connect to a resistive divider from OUT to SET to GND to adjust the output voltage from 2.54V to 11V. 5 OUT_SENSE 6 OUT — EP Output Voltage Sensing Input. OUT_SENSE is used to Kelvin sense the output voltage in fixed-output voltage mode. OUT_SENSE can be left floating or connected directly to the load for accurate load regulation. Regulator Output. Bypass OUT to GND with a minimum 10µF ceramic capacitor. Exposed Pad. Connect to GND for heatsinking. IN MAX5084 MAX5085 1.251V REFERENCE ERROR AMPLIFIER OUT EN STARTUP CIRCUITRY 15Ω OUT_SENSE 5MΩ MUX OVERCURRENT SENSE THERMAL SHUTDOWN SET INTERNAL SHUTDOWN CIRCUITRY GND Figure 1. Block Diagram 6 _______________________________________________________________________________________ 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN The MAX5084/MAX5085 are high-voltage linear regulators with a 6.5V to 65V input voltage range. The devices guarantee 200mA output current and are available with preset output voltages of 3.3V or 5V. Both devices can be used to provide adjustable outputs from 2.54V to 11V by connecting a resistive divider from OUT to SET to GND. Thermal shutdown and short-circuit protection are provided to prevent damage during overtemperature and overcurrent conditions. An output sense pin (OUT_SENSE) provides for Kelvin sensing of the output voltage, thereby reducing the error caused by internal and external resistances. An enable input (EN) allows the regulators to be turned on/off through a logic-level voltage. Driving EN high turns on the device, while driving EN low places the device in a low-power shutdown mode. In shutdown, the supply current reduces to 6µA (typ). Both devices operate over the -40°C to +125°C temperature range and are available in a 3mm x 3mm, 6-pin TDFN package capable of dissipating 1.905W at TA = +70°C. Regulator The regulator accepts an input voltage range from 6.5V to 65V. The MAX5084/MAX5085 offer fixed-output voltages of 5V and 3.3V, respectively. The output voltage is also adjustable from 2.54V to 11V by connecting an external resistive divider network between OUT, SET, and GND (see R1 and R2 in Figure 2). The MAX5084/ MAX5085 automatically determine the feedback path depending on the voltage at SET. Enable Input (EN) EN is a logic-level enable input, which turns the MAX5084/MAX5085 on/off. Drive EN high to turn on the device and drive EN low to place the device in shutdown. When in shutdown, the MAX5084/MAX5085 typically draw 6µA of supply current. EN can withstand voltages up to 65V, allowing EN to be connected to IN for an always-on operation. EN has an internal 5MΩ resistor to GND. Remote Sensing (OUT_SENSE) OUT_SENSE provides for Kelvin sensing of the fixed output voltage, thus eliminating errors due to the voltage drop in the trace resistance between OUT and the load. OUT_SENSE is internally connected to OUT through a 15Ω resistor (Figure 1), and can be left floating when remote sensing is not required. However, if accurate output voltage regulation at the load is required, then connect OUT_SENSE directly to the load. Thermal Protection When the junction temperature exceeds +160°C, an internal thermal sensor signals the shutdown logic to turn off the pass transistor and allows the IC to cool. The thermal sensor turns the pass transistor on again after the junction temperature cools by 10°C. This results in a cycled output during continuous thermal overload conditions. Thermal protection protects the MAX5084/MAX5085 in the event of fault conditions. For continuous operation, do not exceed the maximum junction temperature rating of +150°C. Output Short-Circuit Current Limit The MAX5084/MAX5085 feature a 340mA current limit. The output can be shorted to GND for an indefinite period of time without damage to the device. During a short circuit, the power dissipated across the pass transistor can quickly heat the device. When the die temperature reaches +160°C, the MAX5084/MAX5085 shut down and automatically restart after the die temperature cools by 10°C. This results in a pulsed output operation. Applications Information Output Voltage Setting The MAX5084/MAX5085 feature Dual ModeTM operation: they operate in either a preset output voltage mode or an adjustable output voltage mode. Connect SET to GND for preset output voltage operation. In preset mode, internal feedback resistors set the MAX5084’s internal linear regulator to 5V, and the MAX5085’s internal linear regulator to 3.3V. In adjustable mode, select an output from 2.54V to 11V using a resistive divider (see R1 and R2 in Figure 2) connected from OUT to SET to GND. In adjustable mode, first select the resistor from SET to GND (R2) in the 1kΩ to 100kΩ range. The resistor from OUT to SET (R1) is then calculated by: ⎛V ⎞ R1 = R2 x ⎜ OUT − 1⎟ ⎝ VSET ⎠ where VSET = 1.251V. Available Output Current Calculation The MAX5084/MAX5085 provide up to 200mA of continuous output current. The input voltage extends to 65V. Package power dissipation limits the amount of output current available for a given input/output voltage and ambient temperature. Figure 3 depicts the maximum power dissipation curve for these devices. Dual Mode is a trademark of Maxim Integrated Products, Inc. _______________________________________________________________________________________ 7 MAX5084/MAX5085 Detailed Description OUT IN 10μF 2.4 VOUT = 2.5V TO 11V (200mA) 2.2 2.0 10μF MAX5084 MAX5085 EN GND 1.8 1.6 LOAD OUT_SENSE R1 MAX5084 fig03 VIN = 6.5V TO 65V PD (W) MAX5084/MAX5085 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN MAXIMUM POWER 1.905W 1.4 1.2 1.0 DERATE 23.8mW/°C 0.8 0.6 0.4 SET R2 0.2 0 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) Figure 2. Adjustable Output Voltage Operation Figure 3. Calculated Maximum Power Dissipation vs. Temperature Use Figure 3 to determine the allowable package dissipation for a given ambient temperature. Alternately, use the following formula to calculate the allowable package dissipation: Find the maximum allowable output current. First calculate package dissipation at the given temperature as follows: PD = 1.905W – 0.0238W/°C (85°C – 70°C) = 1.548W Then determine the maximum output current: ⎧1.905W for TA ≤ + 70°C ⎫ PD = ⎨ ⎬ ⎩1.905W – 0.0238W / °C x (TA − 70°C) for + 70°C < TA ≤ + 125°C⎭ After determining the allowable package dissipation, calculate the maximum output current using the following formula: IOUT(MAX) = PD ≤ 2 0 0m A VIN – VOUT The above equations do not include the negligible power dissipation from self-heating due to the device’s ground current. Example 1: TA = +85°C VIN = 14V VOUT = 5V IOUT(MAX) = 1.548W = 172mA 14 V − 5V Example 2: TA = +125°C VIN = 14V VOUT = 3.3V Calculate package dissipation at the given temperature as follows: PD = 1.905W – 0.0238W/°C (125°C – 70°C) = 596mW And establish the maximum output current: IOUT(MAX) = 596mW = 56mA 14 V − 3.3V Example 3: TA = +50°C VIN = 9V VOUT = 5V 8 _______________________________________________________________________________________ 1.905W = 476mA (IOUTMAX = 200mA) 9V − 5V In example 3, the maximum output current is calculated as 476mA, however, the maximum output current cannot exceed 200mA. Alternately, use Figure 4 to quickly determine allowable maximum output current for selected ambient temperatures. VOUT = 5V 250 200 IOUT (mA) IOUT(MAX) = 300 TA ≤ +70°C 150 TA = +85°C 100 TA = +125°C 50 0 5 15 Output Capacitor Selection and Regulator Stability For stable operation over the full temperature range and with load currents up to 200mA, use a 10µF (min) output capacitor with an ESR < 0.5Ω. To reduce noise and improve load-transient response, stability, and power-supply rejection, use larger output capacitor values such as 22µF. Some ceramic dielectrics exhibit large capacitance and ESR variations with temperature. For dielectric capacitors such as Z5U and Y5V, use 22µF or more to ensure stability at temperatures below -10°C. With X7R or X5R dielectrics, 10µF should be sufficient at all operating temperatures. For high-ESR tantalum capacitors use 22µF or more to maintain stability. To improve power-supply rejection and transient response, use a minimum 10µF capacitor between IN and GND. 25 35 45 55 65 VIN (V) Figure 4. Calculated Maximum Output Current vs. Input Voltage Selector Guide OUTPUT VOLTAGE (V) PART TEMP RANGE MAX5084ATT+T -40°C to +125°C 5 or adjustable MAX5085ATT+T -40°C to +125°C 3.3 or adjustable Chip Information PROCESS: BiCMOS _______________________________________________________________________________________ 9 MAX5084/MAX5085 Calculate package dissipation at the given temperature as follows: PD = 1.905W Find the maximum output current: MAX5084 fig04 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 6, 8, &10L, DFN THIN.EPS MAX5084/MAX5085 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN PACKAGE OUTLINE, 6,8,10 & 14L, TDFN, EXPOSED PAD, 3x3x0.80 mm 21-0137 10 ______________________________________________________________________________________ H 1 2 65V, 200mA, Low-Quiescent-Current Linear Regulators in TDFN COMMON DIMENSIONS PACKAGE VARIATIONS SYMBOL MIN. MAX. PKG. CODE N D2 E2 e JEDEC SPEC b A 0.70 0.80 T633-1 6 1.50±0.10 2.30±0.10 0.95 BSC MO229 / WEEA 0.40±0.05 1.90 REF D 2.90 3.10 T633-2 6 1.50±0.10 2.30±0.10 0.95 BSC MO229 / WEEA 0.40±0.05 1.90 REF [(N/2)-1] x e E 2.90 3.10 T833-1 8 1.50±0.10 2.30±0.10 0.65 BSC MO229 / WEEC 0.30±0.05 1.95 REF A1 0.00 0.05 T833-2 8 1.50±0.10 2.30±0.10 0.65 BSC MO229 / WEEC 0.30±0.05 1.95 REF L 0.20 0.40 T833-3 8 1.50±0.10 2.30±0.10 0.65 BSC MO229 / WEEC 0.30±0.05 1.95 REF T1033-1 10 1.50±0.10 2.30±0.10 0.50 BSC MO229 / WEED-3 0.25±0.05 2.00 REF k 0.25 MIN. A2 0.20 REF. T1033-2 10 1.50±0.10 2.30±0.10 0.50 BSC MO229 / WEED-3 0.25±0.05 2.00 REF T1433-1 14 1.70±0.10 2.30±0.10 0.40 BSC ---- 0.20±0.05 2.40 REF T1433-2 14 1.70±0.10 2.30±0.10 0.40 BSC ---- 0.20±0.05 2.40 REF PACKAGE OUTLINE, 6,8,10 & 14L, TDFN, EXPOSED PAD, 3x3x0.80 mm -DRAWING NOT TO SCALE- 21-0137 H 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 11 © 2006 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc. MAX5084/MAX5085 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)