OPTEK OPB931

Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
L Package
Features:
•
•
•
•
•
•
•
Choice of aperture size
Choice of output configurations
Choice of opaque or IR transmissive shell
Choice of pins (L) or wires (W)
0.125” (3.18 mm) slot width
0.320” (8.128 mm) lead spacing for PCBoard (side mounting)
Data rates to 250 kBaud
W Package
Description:
The OPB930 and OPB940 series of Photologic® photo integrated circuit switches provide optimum flexibility for
the design engineer. Building from a standard housing with a 0.125” (3.18 mm) wide slot, a user can specify the
type and polarity of TTL output, discrete shell material, aperture width and either 0.350” (8.9 mm) long pins
(L Series) or 24” (610 mm) AWG, UL listed wire leads (W Series).
All housings are made from an opaque grade of injection-molded plastic that minimizes the assembly’s sensitivity
to both visible and near-infrared ambient radiation. Discrete shells (exposed on the parallel faces inside the device
throat) are either IR transmissive plastic (for applications where aperture contamination may occur) or opaque
plastic (for maximum protection against ambient light).
Electrical output can be specified as either TTL Totem Pole or TTL Open Collector, either of which can be supplied
with buffer or inverter output polarity. All devices have the added stability of a built-in hysteresis amplifier.
Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for
more information.
Applications:
• Mechanical switch replacement
• Speed indication (tachometer)
• Mechanical limit indication
Part Number Guide — OPB930 and OPB940 Series
OPB 9 X X X X X Z———————For “W” series only
Optek Assembly
Sensor Aperture:
1 — 0.010” (2.54 mm)
5 — 0.050” (12.70 mm)
Photologic® Photo Integrated
Circuit Sensor Family
Emitter Aperture:
5 — 0.050” (12.70 mm)
Discrete Shell Material:
3 — Side mount IR transmissive
Plastic discrete shell
Mounting configurations:
L — Solder leads termination
W — Wire termination
4 — Side mount opaque
Plastic discrete shell
RoHS
Electrical Specification Variations:
0 = Buffered Totem-Pole Output
1 = Buffered Open-Collector Output
2 = Inverted Totem-Pole Output
3 = Inverted Open-Collector Output
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2 07/07
Page 1 of 7
Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
OPB930, OPB940 Buffered Totem-Pole
OPB931, OPB941 Buffered Open-Collector
OPB932, OPB942 Inverted Totem-Pole
OPB933 & OPB943 Inverted Open-Collector
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Supply Voltage, VCC (not to exceed 3 seconds)
10 V
Operating Temperature Range
-40°C to +70° C
Storage Temperature Range
-40°C to +85° C
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
(1)
260° C
Input Infrared LED
Input Diode Power Dissipation (2)
100 mW
Output Photologic® Power Dissipation
Total Device Power Dissipation
(3)
(4)
200 mW
300 mW
Output Photologic®
Voltage at Output Lead (Open Collector Output)
35 V
Diode Forward DC Current
40 mA
Diode Reverse DC Voltage
2V
Notes:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
Derate linearly 2.22 mW/°C above 25°.
Derate linearly 4.44 mW/°C above 25°.
Derate linearly 6.66 mW/°C above 25°.
OPB930L/OPB940L series devices are terminated with 0.020” square leads designed for PCBoard mounting.
Methanol and isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and
ketones.
All parameters tested using pulse technique.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.2 07/07
Page 2 of 7
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
DIMENSIONS ARE IN:
Color- Pin # Description
Red—1
Anode
Black—2
Cathode
White—3
VCC
Blue—4
Output
Green—5
Ground
[ MILLIMETERS]
INCHES
PCBoard (L) version
DIMENSIONS ARE IN:
[ MILLIMETERS]
INCHES
Wired (W) version
The W Series includes wire terminations of 24” (610 mm) 7-strand, 26
AWG UL insulated wire on each terminal. Each device incorporates a
wire strain relief at the housing surface. The insulation functions and
colors are: anode (red), cathode (black), phototransistor collector (white)
and phototransistor emitter (green).
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2 07/07
Page 3 of 7
Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode
VF
Forward Voltage
-
-
1.7
V
IF = 20 mA
IR
Reverse Current
-
-
100
µA
VR = 2.0 V
4.75
-
5.25
V
-
-
15
mA
VCC = 5.25, IF = 0 mA(1)
-
-
15
mA
VCC = 5.25, IF = 15 mA
-
-
15
mA
VCC = 5.25, IF = 15 mA
-
-
15
mA
VCC = 5.25, IF = 0 mA(1)
-
-
0.4
V
VCC = 4.75, IOL = 12.8 mA, IF = 0 mA(1)
Inverted Totem-Pole &
Inverted Open-Collector
-
-
0.4
V
VCC = 4.75, IOL = 12.8 mA, IF = 15 mA
High Level Output Voltage:
Totem-Pole & Open-Collector
2.4
-
-
V
VCC = 4.75, IOH = -800 µA, IF = 15 mA
Inverted Totem-Pole &
Inverted Open-Collector
2.4
-
-
V
VCC = 4.75, IOH = -800 µA, IF = 0 mA(1)
-
-
100
µA
-
-
100
µA
VCC = 4.75, VOH = 30 V, IF = 0 mA(1)
-
-
15
mA
VCC = 5.0 V
-
2.0
-
V
VCC = 5.0 V
-15
-
-60
mA
VCC = 5.25 V, IF = 15 mA, Output = GND
-15
-
-60
mA
VCC = 5.25 V, IF = 0 mA(1), Output = GND
Output Rise Time, Output Fall Time
-
70
-
ns
VCC = 5 V, IF = 0 or 15 mA
TPLH
Propagation Delay Low-High
-
5.0
-
µs
RL = 8TTL loads (Totem Pole)
TPHL
Propagation Delay High-Low
-
5.0
-
µs
RL = 360 Ω (Open-Collector)
Output Photologic® Sensor
VCC
ICCL
ICCH
VOL
VOH
IOH
IF(+)
Operating D.C. Supply Voltage
Low Level Supply Current:
Totem Pole & Open-Collector
Inverted Totem-Pole &
Inverted Open-Collector
High Level Supply Current:
Totem Pole & Open-Collector
Inverted Totem-Pole &
Inverted Open-Collector
Low Level Output Voltage:
Totem Pole & Open-Collector
High Level Output Current:
Totem Pole & Open-Collector
Inverted Totem-Pole &
Inverted Open-Collector
LED Positive-Going Threshold Current
IF(+), IF(-) Hysteresis
IOS
trtr
Short Circuit Output Current:
Totem Pole & Open-Collector
Inverted Totem-Pole &
Inverted Open-Collector
-
VCC = 4.75, VOH = 30 V, IF = 15 mA,
Notes:
(1) Normal application would be with light source blocked, simulated by IF = 0 mA.
(2) All parameters are tested using pulse techniques.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.2 07/07
Page 4 of 7
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
OPB930_11, OPB940_11 - Flag Next to Sensor
OPB930_11, OPB940_11 - Flag Next to Emitter
1.20
1.20
1.00
1.00
Right to Left
Right to Left
Right to Left (back)
Right to Left (back)
0.80
0.80
Logic
Logic
Top to Bottom
Bottom to Top
0.60
0.60
Left to Right
Top to Bottom
Bottom to Top
Left to Right
Left to Right (back)
0.40
0.40
Left to Right (back)
0.20
0.20
0.00
0.00
0.05
0.10
0.15
0.20
0.25
0.00
0.00
0.05
Displacement Distance (inches)
0.10
0.15
0.20
0.25
Displacement Distance (inches)
OPB930_11, OPB940_11 - Flag in Middle of Slot
1.20
1.00
Right to Left
Right to Left (back)
Logic
Top to Bottom
0
0.80
Top to Bottom
Bottom to Top
0.60
Left to Right
Left to Right (back)
0.40
Emitter
Left to Right
Right to Left
0.20
Sensor
0.00
0.00
0
0.05
0.10
0.15
0.20
Width
0.25
Displacement Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2 07/07
Page 5 of 7
Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
OPB930_51, OPB940_51 - Flag Next to Sensor
OPB930_51, OPB940_51 - Flag Next to Emitter
1.20
1.20
1.00
1.00
Right to Left
Right to Left
Right to Left (back)
Right to Left (back)
0.80
Top to Bottom
0.60
Logic
Logic
0.80
Bottom to Top
Left to Right
0.40
Top to Bottom
0.60
Bottom to Top
Left to Right
0.40
Left to Right (back)
Left to Right (back)
0.20
0.20
0.00
0.00
0.05
0.10
0.15
0.20
0.25
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Displacement Distance (inches)
Displacement Distance (inches)
OPB930_51, OPB940_51 - Flag in Middle of Slot
1.20
1.00
Right to Left
Right to Left (back)
0
Logic
0.80
0.60
Top to Bottom
Top to Bottom
Bottom to Top
Left to Right
0.40
Emitter
Left to Right (back)
Left to Right
Right to Left
0.20
Sensor
0.00
0.00
0
0.05
0.10
0.15
0.20
Width
0.25
Displacement Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.2 07/07
Page 6 of 7
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Photologic® Slotted Optical Switch
OPB930 and OPB940 (L and W Series)
OPB930_55, OPB940_55 - Flag Next to Sensor
OPB930_55, OPB940_55 - Flag Next to Emitter
1.20
1.20
1.00
1.00
Right to Left
Right to Left (back)
0.80
0.80
Top to Bottom
Bottom to Top
0.60
Logic
Logic
Right to Left
Right to Left (back)
Left to Right
Left to Right
0.40
Top to Bottom
Bottom to Top
0.60
Left to Right (back)
0.40
Left to Right (back)
0.20
0.20
0.00
0.00
0.05
0.10
0.15
0.20
0.25
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Displacement Distance (inches)
Displacement Distance (inches)
OPB930_55, OPB940_55 - Flag in Middle of Slot
1.20
1.00
Right to Left
Right to Left (back)
Logic
0.60
Top to Bottom
0
0.80
Top to Bottom
Bottom to Top
Left to Right
0.40
Left to Right (back)
Emitter
Left to Right
Right to Left
0.20
Sensor
0.00
0.00
0
0.05
0.10
0.15
0.20
Width
0.25
Displacement Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2 07/07
Page 7 of 7