Datasheet - OPTEK Technology

Photologic® Slotted Optical Switch
OPB917 Series
Features:
 Low power consumption
 Data rates to 250 kBaud
 Choice of two logic states and two electrical outputs
 24” (610 mm) minimum 26 AWG UL listed wires
 Slot width 0.20” (5.08 mm)
 Slot Depth 0.86” (21.84 mm)
Description:
The OPB917 series of Photologic® photo integrated circuit switches provide optimum flexibility. Each switch
consists of an infrared Light Emitting Diode (LED) and a Photologic® photo integrated circuit, mounted in an
opaque housing with clear windows for dust protection. The deep slot allows for a longer reach of the optical path
from the 0.650” (16.5 mm) mounting plane. Internal apertures are 0.010” x .060” (.25 mm x 1.52 mm) for the
Photologic’s “S” side and 0.05” x 0.06” (1.27 mm x 1.52 mm) for the LED “E” side.
Devices in this series exhibit stable performance over supply voltages ranging from 4.5 V to 16.0 V, and may be
specified as buffered or inverted with an internal 10 kΩ pull-up resistor or open collector output. Devices are TTL/
LSTTL compatible and can drive up to 10 TTL loads.
Custom electrical, wire or cabling are available. Contact your local representative or OPTEK for more information.
Applications:
 Mechanical switch replacement
 Speed indication (tachometer)
 Mechanical limit indication
 Edge sensing
Ordering Information
Part
Number
OPB917BZ
OPB917IZ
OPB917BOCZ
OPB917IOCZ
LED Peak
Wavelength
Sensor
Photologic®
880 nm
10K Pull-Up
Inv-10K Pull-Up
Open-Collector
Inv-Open-Collector
OPB917BZ 10K Pull-Up
Color
Description
Red
Anode
Black
Cathode
White
Vcc
Blue
Output
Green
Ground
Slot Width/
Depth
Aperture
Emitter/
Sensor
Lead Length /
Wire
0.200” /
0.635”
0.05" / 0.01"
24" / 26 AWG
Wire
OPB917BOCZ Open-Collector
Light ON
output High
Light ON
output High
OPB917IZ Inverted 10K Pull-Up
OPB917IOCZ Inverted Open-Collector
Light ON
output Low
Light ON
output Low
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue C 01/2015
Page 1 of 4
Photologic® Slotted Optical Switch
OPB917 Series
Color
Description
Red
Anode
Black
Cathode
Green
Ground
Blue
Output
White
VCC
[ MILLIMETERS]
DIMENSIONS ARE IN:
INCHES
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage & Operating Temperature Range
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
-40°C to +80°C
(1)
260°C
Input Infrared LED
Supply Voltage, VCC (not to exceed 3 seconds)
Input Diode Power Dissipation
(2)
18 V
100 mW
Forward DC Current
50 mA
Output Photologic®
Voltage at Output Lead (Open Collector Output)
Diode Reverse DC Voltage
2V
Output Photologic® Power Dissipation(3)
Notes:
(1)
(2)
(3)
(4)
(5)
35 V
90 mW
RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
Derate linearly 1.33 mW/°C above 25°.
Derate linearly 2.50 mW/°C above 25°.
Normal application would be with light source blocked, simulated by IF = 0 mA.
All parameters tested using pulse technique.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue C 01/2015
Page 2 of 4
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Photologic® Slotted Optical Switch
OPB917 Series
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode
VF
Forward Voltage
-
1.3
1.8
V
IF = 20 mA
IR
Reverse Current
-
-
100
µA
VR = 2 V, TA = 25° C
4.5
-
16
V
-
Output Photologic® Sensor
VCC
Operating DC Supply Voltage
-
-
7
mA
VCC = 16 V, IF = 0 mA, No Output Load
ICCL
Low Level Supply Current:
Buffered with 10k pull-up(1)
Buffered Open-Collector Output(1)
Inverted with 10k pull-up:
Inverted Open-Collector Output
-
-
7
mA
VCC = 16 V, IF = 10 mA, No Output Load
High Level Supply Current:
Buffered with 10k pull-up
Buffered Open-Collector Output
-
-
6
mA
VCC = 16 V, IF = 10 mA, No Output Load
-
-
6
mA
VCC = 16 V, IF = 0 mA, No Output Load
Low Level Output Voltage:
Buffered with 10k pull-up
Buffered Open-Collector Output
-
-
0.4
0.4
V
VCC = 4.5 V, IOL = 0 mA, IF = 0 mA
VCC = 4.5 V, IOL = 16 mA, IF = 0 mA
Inverted with 10k pull-up:
Inverted Open-Collector Output
-
-
0.4
0.4
V
VCC = 4.5 V, IOL = 0 mA, IF = 10 mA
VCC = 4.5 V, IOL = 16 mA, IF = 10 mA
VCC
2.4
Vcc-1.5
-
V
VCC
2.4
Vcc-1.5
-
V
VCC = 4.5 V to 16 V, IF = 0 mA,
No Output Load
-
1.0
14
µA
VCC = 4.5 V, IF = 10 mA, VOH = 30 V
-
1.0
14
µA
VCC = 4.5 V, IF = 0 mA, VOH = 30 V
-
5
10
mA
VCC = 5 V, IOL = 0 mA
-
5
10
mA
VCC = 4.5 V, IOL = 16 mA
Hysteresis
-
1.5
-
-
Rise Time, Fall Time
-
50
-
ns
Propagation Delay
-
3
-
µs
ICCH
Inverted with 10k pull-up:
Inverted Open-Collector Output(1)
VOL
VOH
High Level Output Voltage:
Buffered with 10k pull-up
Buffered Open-Collector Output
Inverted with 10k pull-up:
Inverted Open-Collector Output(1)
IOH
High Level Output Voltage:
Buffered with 10k pull-up
Buffered Open-Collector Output
Inverted with 10k pull-up:
Inverted Open-Collector Output(1)
IF(+)
LED Positive-Going Threshold Current
Buffered with 10k pull-up
Buffered Open-Collector Output
Inverted with 10k pull-up:
Inverted Open-Collector Output(1)
IF(+)/IF(-)
trtf
tPLHtPHL
.
VCC = 4.5 V to 16 V, IF = 10 mA,
No Output Load
VCC = 5 V
VCC = 5 V, IF = 0 or 10 mA,
RL = 300 Ω to 5 V, CL = 50 pF
Notes:
(1) Normal application would be with light source blocked, simulated by IF = 0 mA.
(2) All parameters tested using pulse technique.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue C 01/2015
Page 3 of 4
Photologic® Slotted Optical Switch
OPB917 Series
OPB917—Flag
OPB916B - FlagNext
Nextto
to Emitter
Emitter
OPB917—Flag
toSensor
Sensor
OPB916B - FlagNext
Next to
1.20
1.20
1.00
1.00
Right to Left
Right to Left (back)
0.80
0.80
Top to Bottom
Bottom to Top
0.60
Top to Bottom
Bottom to Top
Logic
Logic
Right to Left
Right to Left (back)
Left to Right
0.60
Left to Right
Left to Right (back)
Left to Right (back)
0.40
0.40
0.20
0.20
0.00
0.00
0.05
0.10
0.15
0.20
0.25
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Displacement (inches)
Displacement (inches)
OPB917—Flag
Middle
OPB916B - Flag in
Middleof
ofSlot
Slot
1.20
1.00
0
Right to Left
Top to Bottom
Right to Left (back)
Logic
0.80
Top to Bottom
Bottom to Top
0.60
Left to Right
Emitter
Left to Right (back)
Left to Right
0.40
Right to Left
Sensor
0.20
0
Width
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue C 01/2015
Page 4 of 4
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com