Photologic® Slotted Optical Switch OPB916 Series Features: • • • • • • Low power consumption Data rates to 250 kBaud Choice of two logic states and two electrical outputs 24” (610 mm) minimum 26 AWG UL listed wires Slot width 0.20” (5.08 mm) Slot Depth 0.635” (16.13 mm) Product Photo Here Description: The OPB916 series of Photologic® photo integrated circuit switches provide optimum flexibility. Each switch consists of an infrared Light Emitting Diode (LED) and a Photologic® photo integrated circuit, mounted in an opaque housing with clear windows for dust protection. The deep slot allows for a longer reach of the optical path from the 0.650” (16.5 mm) mounting plane. Internal apertures are 0.010” x .060” (.25 mm x 1.52 mm) for the Photologic’s “S” side and 0.05” x 0.06” (1.27 mm x 1.52 mm) for the LED “E” side. Devices in this series exhibit stable performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as buffered or inverted with an internal 10 kΩ pull-up resistor or open collector output. Devices are TTL/ LSTTL compatible and can drive up to 10 TTL loads. Custom electrical, wire or cabling are available. Contact your local representative or OPTEK for more information. Applications: • Mechanical switch replacement • Speed indication (tachometer) • Mechanical limit indication • Edge sensing Ordering Information Part Number OPB916BZ OPB916IZ OPB916BOCZ OPB916IOCZ LED Peak Wavelength 880 nm Sensor Photologic® 10K Pull-Up Inv-10K Pull-Up Open-Collector Inv-Open-Collector OPB916B 10K Pull-Up Color Description Red Anode Black Cathode White Vcc Blue Output Green Ground Slot Width / Depth Aperture Emitter / Sensor Lead Length / Wire 0.200” / 0.635” 0.05" / 0.01" 24" / 26 AWG Wire OPB916BOC Open-Collector Light ON output High Light ON output High OPB916I Inverted 10K Pull-Up OPB916IOC Inverted Open-Collector Light ON output Low Light ON output Low RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.3 08/08 Page 1 of 4 Photologic® Slotted Optical Switch OPB916 Series Color-Pin # Description Red Anode Black Cathode Green Ground Blue Output White VCC Tolerence ±0.010 [0.254] DIMENSIONS ARE IN: [ MILLIMETERS] INCHES Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage & Operating Temperature Range -40°C to +80°C Input Infrared LED Diode Reverse DC Voltage Input Diode Power Dissipation 2V (2) 75 mW Forward DC Current 50 mA Output Photologic® Supply Voltage, VCC (not to exceed 3 seconds) 18 V Voltage at Output Lead (Open Collector Output) 30 V (3) Output Photologic® Power Dissipation Notes: (1) (2) (3) (4) (5) 90 mW RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.67 mW/°C above 25°. Derate linearly 2.67 mW/°C above 25°. Normal application would be with light source blocked, simulated by IF = 0 mA. All parameters tested using pulse technique. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .3 08/08 Page 2 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic® Slotted Optical Switch OPB916 Series Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNIT S TEST CONDITIONS Input Diode VF Forward Voltage - 1.3 1.8 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V, TA = 25° C 4.5 - 16 V - Output Photologic® Sensor VCC Operating DC Supply Voltage - - 7 mA VCC = 16 V, IF = 0 mA, No Output Load ICCL Low Level Supply Current: Buffered with 10k pull-up(1) Buffered Open-Collector Output(1) Inverted with 10k pull-up: Inverted Open-Collector Output - - 7 mA VCC = 16 V, IF = 10 mA, No Output Load - - 6 mA VCC = 16 V, IF = 10 mA, No Output Load - - 6 mA VCC = 16 V, IF = 0 mA, No Output Load - - 0.4 V VCC = 4.5 V, IOL = 16 mA, IF = 0 mA - - 0.4 V VCC = 4.5 V, IOL = 16 mA, IF = 10 mA ICCH High Level Supply Current: Buffered with 10k pull-up Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output(1) VOL Low Level Output Voltage: Buffered with 10k pull-up Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output VOH IOH VCC-2.0 - - V Inverted with 10k pull-up: VCC-2.0 - - V VCC = 4.5 V to 16 V, IF = 0 mA, - 1.0 10 µA VCC = 4.5 V, IF = 10 mA, VOH = 30 V - 1.0 10 µA VCC = 4.5 V, IF = 0 mA, VOH = 30 V - 5 10 mA VCC = 5 V, No Output Load - 5 10 mA VCC = 4.5 V, IOL = 16 mA Hysteresis - 1.5 - - Rise Time, Fall Time - 50 - ns Propagation Delay - 3 - µs High Level Output Current: Buffered with 10k pull-up Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output(1) IF(+) LED Positive-Going Threshold Current Buffered with 10k pull-up Inverted with 10k pull-up Buffered Open-Collector Output Inverted Open-Collector Output(1) IF(+)/IF(-) trtf tPLHtPHL . VCC = 4.5 V to 16 V, IF = 10 mA, IOH = 100 µA High Level Output Voltage: Buffered with 10k pull-up VCC = 5 V VCC = 5 V, IF = 0 or 10 mA, RL = 300 Ω to 5 V, CL = 50 pF Notes: (1) Normal application would be with light source blocked, simulated by IF = 0 mA. (2) All parameters tested using pulse technique. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.3 08/08 Page 3 of 4 Photologic® Slotted Optical Switch OPB916 Series OPB916B - Flag Next to Emitter OPB916B - Flag Next to Sensor 1.20 1.20 1.00 1.00 Right to Left Right to Left (back) 0.80 0.80 Top to Bottom Bottom to Top 0.60 Top to Bottom Bottom to Top Logic Logic Right to Left Right to Left (back) Left to Right 0.60 Left to Right Left to Right (back) Left to Right (back) 0.40 0.40 0.20 0.20 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement (inches) Displacement (inches) OPB916B - Flag in Middle of Slot 1.20 1.00 0 Right to Left Top to Bottom Right to Left (back) Logic 0.80 Top to Bottom Bottom to Top 0.60 Left to Right Emitter Left to Right (back) Left to Right 0.40 Right to Left Sensor 0.20 0 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .3 08/08 Page 4 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com