Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) Features: • • • • Non-contact switching PCBoard mounting Product Photo Here Enhanced signal to noise ratio Choice of four Logical output options Description: Each OPB615, OPB625 and OPB665 series slotted optical switch consists of an 890 nm, infrared Light Emitting Diode (LED) and a monolithic integrated circuit that incorporates a photodiode, a linear amplifier and a Schmitt trigger on a single silicon chip. OPB665 offers two mounting options -- no tabs (N) or two tabs (T). All devices in this series exhibit performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as Buffered or Inverted with 10 kW Pull-up or Open Collector output. Devices are also TTI/LSTTL compatible and can drive up to 10 TTL loads. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: • Mechanical switch replacement • Speed indication (tachometer) • Mechanical limit indication • Edge sensing Ordering Information Part Number Package Style OPB615 10K Pull-up OPB616 Open Collector OPB617 Inv-10K Pull-up OPB618 Inv-Open Collector OPB625 10K Pull-up OPB626 OPB627 N OPB628 Open Collector 10K Pull-up Open Collector OPB667N Inv-10K Pull-Up OPB668N Inv-Open Collector OPB665T 10K Pull-up OPB668T Slot Width / Lead Length / Depth Spacing None 0.150" / 0.240” None 0.190" / 0.285” 0.100" (min) / 0.275" Inv-Open Collector OPB666N OPB667T Aperture Emitter / Sensor Inv-10K Pull-up OPB665N OPB666T RoHS Sensor Photologic® T 0.100" (min) / 0.320" 0.05”/ 0.01” 0.125" / 0.345” Open Collector Inv-10K Pull-up Inv-Open Collector OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.2 04/09 Page 1 of 8 Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) OPB615/625/665N Buffered 10K Pull-Up OPB617/627/667N Inverted 10K Pull-Up OPB 616/626/666N Buffered Open-Collector OPB618/628/668N Inverted Open-Collector OPB615, OPB616, OPB617, OPB618 Pin Color/ Number Description 1 Anode 2 Cathode 3 Vcc 4 Output 5 Ground [ MILLIMETERS] DIMENSIONS ARE IN: INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 04/09 Page 2 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) OPB625, OPB626, OPB627, OPB628 Pin Color/ Number Description 1 Anode 2 Cathode 3 Vcc 4 Output 5 Ground OPB665, OPB666, OPB667, OPB668 (N and T) [ MILLIMETERS] Pin Color/ Number Description 1 Anode 2 Cathode 3 Vcc 4 Output 5 Ground DIMENSIONS ARE IN: INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.2 04/09 Page 3 of 8 Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage & Operating Temperature Range -40° C to +100° C Lead Soldering Temperature (1/16 inch (1.6mm) from the case for 5 sec. with soldering iron) (1) 260° C Input Diode Forward DC Current 50 mA Peak Forward Current (1 μs pulse width, 300 pps) 3A Reverse DC Voltage 3V (2) 100 mW Supply Voltage, VCC 18 V Power Dissipation Output Photologic® 1 second Duration of Output Short to VCC Voltage at Output (5) Vcc Low Level Output Current (sinking) Power Dissipation Notes: (1) (2) (3) (4) (5) 16 mA (3) 240° mW RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.33 mW/° C above 25° C. Derate linearly 2.50 mW/° C above 25° C. Normal application would be with light source blocked, simulated by IF = 0 mA. Open Collector devices = 30 volts Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode VF Forward Voltage - - 1.6 V IF = 10 mA IR Reverse Current - - 100 μA VR = 3 V 4.5 - 16 V 0.1 0.1 0.1 0.55 0.6 1.6 3 3 10 mA 1.05 1.20 1.90 Output Photologic® Sensor VCC Operating DC Supply Voltage IF(+) LED Positive-Going Threshold Current IF(+)/IF(-) Hysteresis OPB615-618 OPB625-628 OPB665-668 VCC = 5 V VCC = 5 V OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 04/09 Page 4 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Output Photologic® Sensor ICCH ICCL VOH IOH VOL tr, tf tPLH tPHL Data Rate Notes: (1) (2) (3) (4) High Level Supply Current: Buffer, 10k Pull-up Buffer, Open-Collector OPB615, 625, 665 OPB616, 626, 666 - 5 5 12 12 mA NO LOAD on Output(3) Inverted, 10k Pull-up Inverted, Open-Collector OPB617, 627, 667 OPB618, 628, 668 - 4 4 12 12 mA NO LOAD on Output IF = 0 mA Low Level Supply Current: Buffer, 10k Pull-up Buffer, Open-Collector OPB615, 625, 665 OPB616, 626, 666 - 5.5 4.0 12 12 mA NO LOAD on Output IF = 0 mA Inverted, 10k Pull-up Inverted, Open-Collector OPB617, 627, 667 OPB618, 628, 668 - 6.5 5.0 12 12 mA NO LOAD on Output(3) High Level Output Voltage: Buffer, 10k Pull-up Buffer, Open-Collector OPB615, 625, 665 VCC-1.5 OPB616, 626, 666 - - V IOH = 100 µA(3) Inverter, 10k Pull-up Inverter, Open-Collector OPB617, 627, 667 OPB618, 628, 668 VCC-1.5 - - V IOH = 100 µA(1) High Level Output Voltage: Buffer, Open-Collector OPB616, 626, 666 - - 100 µA VOH = 30 V(3) Inverter, Open-Collector OPB618, 628, 668 - - 100 µA IF = 0 mA, VOH = 30 V(1) Low Level Output Voltage: Buffer, 10k Pull-up Buffer, Open-Collector OPB615, 625, 665 OPB616, 626, 666 - - 0.4 V IOL = 16 mA, Vcc = 4.5 V(3)(1) Inverter, 10k Pull-up Inverter, Open-Collector OPB617, 627, 667 OPB618, 628, 668 - - 0.4 V IOL = 16 mA, IF = 0 mA Output Rise Time, Output Fall Time 30 ns Propagation Delay, Low-High Buffer, 10k Pull-up Buffer, Open-collector OPB615, 625, 665 OPB616, 626, 666 0.6 µs Inverter, 10k Pull-up Inverter, Open-Collector OPB617, 627, 667 OPB618, 628, 668 3.0 µs Propagation Delay, High-Low Buffer, 10k Pull-up Buffer, Open-collector OPB615, 625, 665 OPB616, 626, 666 3.0 µs Inverter, 10k Pull-up Inverter, Open-Collector OPB617, 627, 667 OPB618, 628, 668 0.6 µs - 100 - kHz IF = 0 mA f = 10 kHz, RL = 300 Ω, DC = 50%(3) RL = 300 Ω, DC = 50%(4) Normal application would be with light source blocked, simulated by IF = 0 mA. VOH = VCC-1.5V for VCC = 4.5 to 16 Volts. IF = 5 mA OPB615 to OPB628; IF = 10 mA OPB665 to OPB668 IF = 0 to 5 mA OPB615 to OPB628; IF = 0 to 10 mA OPB665 to OPB668 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.2 04/09 Page 5 of 8 Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) OPB615 - Flag next to Sensor OPB615 - Flag next to Emitter 1.20 1.20 1.00 1.00 Right to Left Back Right to Left Back 0.80 0.80 Top to Bottom Logic Logic Top to Bottom Right to Left 0.60 Bottom to Top Right to Left 0.60 Bottom to Top 0.40 0.40 Left to Right Left to Right Back Left to Right Left to Right Back 0.20 0.20 0.00 0.000'' 0.050'' 0.100'' 0.150'' 0.200'' 0.250'' 0.00 0.000'' 0.050'' 0.100'' 0.150'' 0.200'' 0.250'' Displacement(inches) Displacement(inches) OPB615 - Flag in Middle of Slot 1.20 0 1.00 Top to Bottom Right to Left Back 0.80 Logic Top to Bottom Right to Left 0.60 Emitter Bottom to Top Left to Right Right to Left 0.40 Left to Right Sensor Left to Right Back 0 0.20 0.00 0.000'' 0.050'' 0.100'' 0.150'' 0.200'' Width 0.250'' Displacement(inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 04/09 Page 6 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) OPB625 - Flag Next to Sensor OPB625 - Flag Next to Emitter 1.2 1.2 1 1 Right to Left Back Right to Left Back 0.8 0.8 Top to Bottom Right to Left 0.6 Logic Logic Top to Bottom Bottom to Top Right to Left 0.6 Bottom to Top 0.4 0.4 Left to Right Left to Right Back Left to Right Left to Right Back 0.2 0.2 0 0 0.00 0.05 0.10 0.15 0.20 0.00 0.25 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) Displacement Distance (inches) OPB625 - Flag in Middle of Slot 1.20 1.00 0 Top to Bottom Right to Left Back 0.80 Logic Top to Bottom Right to Left 0.60 Emitter Bottom to Top Left to Right Right to Left 0.40 Left to Right Sensor Left to Right Back 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.2 04/09 Page 7 of 8 Photologic® Slotted Optical Switch OPB615, OPB616, OPB617, OPB618 Series OPB625, OPB626, OPB627, OPB628 Series OPB665, OPB666, OPB667, OPB668 (N and T Series) OPB665 - Flag next to Emitter OPB665 - Flag next to Sensor 1.20 1.20 1.00 1.00 Right to Left Back Right to Left Back 0.80 0.80 Right to Left Right to Left Top to Bottom Logic Logic Top to Bottom 0.60 Bottom to Top 0.40 0.60 Bottom to Top 0.40 Left to Right Back Left to Right Left to Right Back Left to Right 0.20 0.20 0.00 0.00 0.000'' 0.050'' 0.100'' 0.150'' 0.200'' 0.250'' 0.000'' 0.050'' 0.100'' Displacement(inches) 0.150'' 0.200'' 0.250'' Displacement(inches) OPB665 - Flag in Middle of Slot 1.20 0 1.00 Top to Bottom Right to Left Back 0.80 Right to Left Logic Top to Bottom 0.60 Emitter Bottom to Top Left to Right Right to Left 0.40 Sensor Left to Right Back Left to Right 0 0.20 0.00 0.000'' 0.050'' 0.100'' 0.150'' 0.200'' Width 0.250'' Displacement(inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 04/09 Page 8 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com