LC2MOS Microprocessor-Compatible 14-Bit DAC AD7538 FEATURES FUNCTIONAL BLOCK DIAGRAM VDD All grades 14-bit monotonic over the full temperature range Low cost, 14-bit upgrade for 12-bit systems 14-bit parallel load with double buffered inputs Small 24-pin, 0.30” DIP and SOIC Low output leakage (<20 nA) over the full temperature range VREF 1 APPLICATIONS Microprocessor-based control systems Digital audio Precision servo control Control and measurement in high temperature environments 2 RFB 14-BIT DAC 3 IOUT 4 AGND DAC REGISTER 20 LDAC INPUT REGISTER 21 CS 22 WR 14 6 5 24 DGND VSS 19 DB13 TO DB0 01139-001 23 AD7538 Figure 1. GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD7538 is a 14-bit monolithic CMOS digital-to-analog converter (DAC) that uses laser trimmed thin-film resistors to achieve excellent linearity. 1. The DAC is loaded by a single 14-bit wide word using standard chip select and memory write logic. Double buffering, which is optional using LDAC, allows simultaneous updates in a system containing multiple AD7538s. 2. 3. A novel low leakage configuration enables the AD7538 to exhibit excellent output leakage current characteristics over the specified temperature range. 4. The AD7538 is manufactured using the linear-compatible CMOS (LC2MOS) process. It is speed compatible with most microprocessors and accepts TTL or CMOS logic level inputs. 5. Guaranteed Monotonicity. The AD7538 is guaranteed monotonic to 14-bits over the full temperature range for all grades. Low Cost. The AD7538, with its 14-bit dynamic range, affords a low cost solution for 12-bit system upgrades. Small Package Size. The AD7538 is packaged in a small 24-pin, 0.3" DIP and a 24-pin SOIC. Low Output Leakage. By tying VSS (Pin 24) to a negative voltage, it is possible to achieve a low output leakage current at high temperatures. Wide Power Supply Tolerance. The device operates on a +12 V to +15 V VDD, with a ±5% tolerance on this nominal figure. All specifications are guaranteed over this range. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2009 Analog Devices, Inc. All rights reserved. AD7538 TABLE OF CONTENTS Features .............................................................................................. 1 Equivalent Circuit Analysis ...................................................... 10 Applications ....................................................................................... 1 Digital Section ............................................................................ 10 Functional Block Diagram .............................................................. 1 Unipolar Binary Operation (2-Quadrant Multiplication) .... 10 General Description ......................................................................... 1 Bipolar Operation (4-Quadrant Multiplication) .................... 11 Product Highlights ........................................................................... 1 Low Leakage Configuration...................................................... 11 Revision History ............................................................................... 2 Programmable Gain Amplifier ................................................. 12 Specifications..................................................................................... 3 Application Hints ........................................................................... 13 AC Performance Characteristics ................................................ 4 Output Offset .............................................................................. 13 Timing Characteristics ................................................................ 4 General Ground Management.................................................. 13 Timing Diagram ........................................................................... 5 Microprocessor Interfacing ....................................................... 13 Absolute Maximum Ratings............................................................ 6 AD7538-to-8086 Interface ........................................................ 13 ESD Caution .................................................................................. 6 AD7538-to-MC68000 Interface ............................................... 13 Pin Configuration and Function Descriptions ............................. 7 Digital Feedthrough ................................................................... 14 Terminology ...................................................................................... 8 Outline Dimensions ....................................................................... 15 DAC Section ...................................................................................... 9 Ordering Guide .......................................................................... 16 Circuit Information ........................................................................ 10 REVISION HISTORY 1/09—Rev. A to Rev. B Updated Format .................................................................. Universal Changes to Table 1 ............................................................................ 3 Updated Outline Dimensions ....................................................... 15 Changes to Ordering Guide .......................................................... 15 5/87—Rev. 0 to Rev. A Rev. B | Page 2 of 16 AD7538 SPECIFICATIONS VDD = 11.4 V to 15.75 V 1 , VREF = 10 V; VPIN3 = VPIN4 = 0 V, VSS = −300 mV; all specifications TMIN to TMAX, unless otherwise noted. Table 1. A, J Versions B, K Versions S Version T Version Unit 14 ±2 14 ±1 14 ±2 14 ±1 Bits LSB max ±1 ±1 ±1 ±1 LSB max ±4 ±8 ±2 ±4 ±5 ±2 ±4 ±10 ±2 ±4 ±6 ±2 LSB max LSB max ppm/°C typ ±5 ±10 ±25 ±5 ±10 ±25 ±5 ±20 ±150 ±5 ±20 ±150 nA max nA max nA max All digital inputs 0 V VSS = –300 mV VSS = 0 V 3.5 10 3.5 10 3.5 10 3.5 10 kΩ min kΩ max Typical input resistance = 6 kΩ 2.4 0.8 2.4 0.8 2.4 0.8 2.4 0.8 V min V max ±1 ±10 7 ±1 ±10 7 ±1 ±10 7 ±1 ±10 7 μA max μA max pF max VIN = 0 V or VDD 11.4/15.75 11.4/15.75 11.4/15.75 11.4/15.75 V min/V max VSS Range −200/−500 −200/−500 −200/−500 −200/−500 IDD 4 500 4 500 4 500 4 500 mV min/ mV max mA max μA max Specification guaranteed over this range Specification guaranteed over this range All digital inputs are VIL or VIH All digital inputs are 0 V or VDD Parameter 2 ACCURACY Resolution Relative Accuracy Differential Nonlinearity Full-Scale Error +25°C TMIN to TMAX Gain Temperature Coefficient 3 ; ΔGain/ΔTemperature Output Leakage Current IOUT (Pin 3) 25°C TMIN to TMAX TMIN to TMAX REFERENCE INPUT Input Resistance (Pin 1) DIGITAL INPUTS VIH (Input High Voltage) VIL (Input Low Voltage) IIN (Input Current) 25°C TMIN to TMAX CIN (Input Capacitance)3 POWER SUPPLY VDD Range 1 Test Conditions/Comments All grades guaranteed monotonic Over temperature Measured using internal RFB DAC Registers loaded with all 1s Specifications are guaranteed for a VDD of 11.4 V to 15.75 V. At VDD = 5 V, the device is fully functional with degraded specifications. Temperature range as follows: J, K Versions: 0°C to +70°C A, B Versions: −25°C to +85°C S, T Versions: −55°C to +125°C 3 Sample tested to ensure compliance. 2 Rev. B | Page 3 of 16 AD7538 AC PERFORMANCE CHARACTERISTICS These characteristics are included for design guidance only and are not subject to test. VDD = 11.4 V to 15.75 V, VREF = 10 V, VPIN3 = VPIN4 = 0 V, VSS = 0 V or −300 mV, output amplifier is AD711 except where noted. Table 2. Parameter Output Current Settling Time TA = 25°C TA = TMIN, TMAX 1.5 Unit μs max Digital-to-Analog Glitch Impulse 20 nV-sec typ Multiplying Feedthrough Error 3 5 mV p-p typ ±0.01 ±0.02 % per % max ΔVDD = ±5% 260 130 260 130 pF max pF max DAC register loaded with all 1s DAC register loaded with all 0s nV√Hz typ Measured between RFB and IOUT Power Supply Rejection ΔGain/ΔVDD Output Capacitance COUT (Pin 3) COUT (Pin 3) Output Noise Voltage Density (10 Hz to 100 kHz) 15 Test Conditions/Comments To 0.003% of full-scale range IOUT load= 100 Ω, CEXT = 13 pF DAC register alternately loaded with all 1s and all 0s; typical value of settling time is 0.8 μs Measured with VREF = 0 V. IOUT load = 100 Ω, CEXT = 13 pF; DAC register alternately loaded with all 1s and all 0s VREF = ±10 V, 10 kHz sine wave DAC Register loaded with all 0s TIMING CHARACTERISTICS VDD = 11.4 V to 15.75 V, VREF = 10 V, VPIN3 = VPIN4 = 0 V, VSS = 0 V or −300 mV. All specifications TMIN to TMAX unless otherwise noted. See Figure 2 for a timing diagram. Table 3. Parameter 1 Limit at TA = +25°C Limit at TA = 0°C to +70°C TA = −25°C to +85°C Limit at TA = −55°C to +125°C Unit Test Conditions/Comments t1 t2 t3 t4 t5 t6 0 0 170 170 140 20 0 0 200 200 160 20 0 0 240 240 180 30 ns min ns min ns min ns min ns min ns min CS to WR setup time CS to WR hold time LDAC pulse width Write pulse width Data setup time Data hold time 1 Temperature range as follows: J, K Versions: 0°C to +70°C A, B Versions: −25°C to +85°C S, T Versions: −55°C to +125°C Rev. B | Page 4 of 16 AD7538 TIMING DIAGRAM t1 t2 5V CS 0V t3 LDAC 5V 0V t4 5V WR 0V t6 5V DATA 0V NOTES 1. ALL INPUT SIGNAL RISE AND FALL TIMES MEASURES FROM 10% TO 90% OF 5V, tR = tF = 20ns. VIH + VIL 2. TIMING MEASUREMENT REFERENCE LEVEL IS . 2 3. IF LDAC IS ACTIVATED PRIOR TO THE RISING EDGE OF WR, THEN IT MUST STAY LOW FOR t3 OR LONGER AFTER WR GOES HIGH. Figure 2. Timing Diagram Rev. B | Page 5 of 16 01139-002 t5 AD7538 ABSOLUTE MAXIMUM RATINGS TA = +25°C unless, otherwise stated. Table 4. Parameter VDD (Pin 23) to DGND VSS (Pin 24) to AGND VREF (Pin 1) to AGND VRFB (Pin 2) to AGND Digital Input Voltage (Pins 6 to 22) to DGND VPIN3 to DGND AGND to DGND Power Dissipation (Any Package) To 75°C Derates Above 75°C Operating Temperature Range Commercial (J, K Versions) Industrial (A, B Versions) Extended (S, T Versions) Storage Temperature Lead Temperature (Soldering, 10 sec) Rating −0.3 V, +17 V −15 V, +0.3 V ±25 V ±25 V −0.3 V, VDD +0.3 V −0.3 V, VDD +0.3 V −0.3 V, VDD +0.3 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 1000 mW 10 mW/°C 0°C to +70°C −25°C to +85°C −55°C to +125°C −65°C to +150°C 300°C Rev. B | Page 6 of 16 AD7538 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS VREF 1 24 VSS RFB 2 23 VDD IOUT 3 22 WR DGND 5 (MSB) DB13 6 DB12 7 AD7538 21 CS 20 LDAC TOP VIEW (Not to Scale) 19 DB0 (LSB) 18 DB1 DB11 8 17 DB2 DB10 9 16 DB3 DB9 10 15 DB4 DB8 11 14 DB5 DB7 12 13 DB6 01139-003 AGND 4 Figure 3. Pin Configuration Table 5. Pin Function Description Pin No. 1 2 3 4 5 6 to 19 20 21 22 Mnemonic VREF RFB IOUT AGND DGND DB13 to DB0 LDAC CS WR Description Voltage Reference. Feedback Resistor. Used to close the loop around an external op amp. Current Output Terminal. Analog Ground Digital Ground. Data Inputs. Bit DB13 (MSB) to Bit DB0 (LSB). Chip Select Input. Active low. Asynchronous Load DAC Input. Active low. Write Input. Active low. CS LDAC WR Operation 0 1 0 Load input register. 1 0 X1 Load DAC register from input register. 0 0 0 Input and DAC registers are transparent. 1 1 X1 No operation. X1 1 1 No operation. +12 V to +15 V Supply Input. Bias pin for high temperature low leakage configuration. To implement low leakage system, the pin should be at a negative voltage. See Figure 6 and Figure 8 for recommended circuitry. X 23 24 1 VDD VSS X = don’t care. Rev. B | Page 7 of 16 AD7538 TERMINOLOGY Relative Accuracy Relative accuracy or endpoint nonlinearity is a measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function. It is measured after adjusting for zero error and full-scale error and is normally expressed in least significant bits or as a percentage of fullscale reading. Digital-To-Analog Glitch Impulse The amount of charge injected from the digital inputs to the analog output when the inputs change state is called digital-toanalog glitch impulse. This is normally specified as the area of the glitch in either pA-secs or nV-secs depending upon whether the glitch is measured as a current or voltage. It is measured with VREF = AGND. Differential Nonlinearity Differential nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of ±1 LSB maximum over the operating temperature range ensures monotonicity. Output Capacitance This is the capacitance from IOUT to AGND. Gain Error Gain error is a measure of the output error between an ideal DAC and the actual device output. It is measured with all 1s in the DAC after the offset error has been adjusted out and is expressed in least significant bits. Gain error is adjustable to zero with an external potentiometer. Output Leakage Current Output leakage current is current which appears at IOUT with the DAC register loaded to all 0s. Multiplying Feedthrough Error This is the ac error due to capacitive feedthrough from the VREF terminal to IOUT with the DAC register loaded to all zeros. Rev. B | Page 8 of 16 AD7538 DAC SECTION Switch A to Switch G steer equally weighted currents between IOUT and AGND. Figure 4 shows a simplified circuit diagram for the AD7538 DAC section. The three MSBs of the 14-bit data word are decoded to drive the seven switches (A to G). The 11 LSBs of the data word consist of an R-2R ladder operated in a current steering configuration. Because the input resistance at VREF is constant, it may be driven by a voltage source or a current source of positive or negative polarity. The R-2R ladder current is ⅛ of the total reference input current. ⅞ current flows in the parallel ladder structure. 2R 2R 2R 2R 2R 2R R 2R R 2R 2R 2R 2R R/4 G F E D C B A S10 S9 S0 RFB IOUT AGND Figure 4. Simplified Circuit Diagram for the AD7538 DAC Section Rev. B | Page 9 of 16 01139-004 R VREF AD7538 CIRCUIT INFORMATION Figure 5 shows an equivalent circuit for the analog section of the AD7538 DAC. The current source ILEAKAGE is composed of surface and junction leakages. The RO resistor denotes the equivalent output resistance of the DAC, which varies with input code. COUT is the capacitance due to the current steering switches and varies from about 90 pF to 180 pF (typical values) depending upon the digital input. g(VREF, N) is the Thevenin equivalent voltage generator due to the reference input voltage, VREF, and the transfer function of the DAC ladder, N. R/4 RO VDD R2 10Ω 1 23 2 VREF VDD RFB LDAC 20 LDAC CS 21 CS C1 33pF IOUT 3 AD7538 AGND 4 WR 22 WR DB13 TO DB0 DGND 6 19 5 DIGITAL GND INPUT DATA VSS C2 4.7µF + 24 R3 1kΩ R4 47kΩ RFB IOUT ILEAKAGE A1 AD711 VO ANALOG GND –15V Figure 6. Unipolar Binary Operation COUT AGND 01139-005 g (VREF , N) R1 20Ω VIN 01139-006 EQUIVALENT CIRCUIT ANALYSIS Table 6. Unipolar Binary Code Table Figure 5. AD7538 Equivalent Analog Output Circuit DIGITAL SECTION The digital inputs are designed to be both TTL and 5 V CMOS compatible. All logic inputs are static protected MOS gates with typical input currents of less than 1 nA. To minimize power supply currents, it is recommended that the digital input voltages be driven as close as possible to 0 V and 5 V logic levels. UNIPOLAR BINARY OPERATION (2-QUADRANT MULTIPLICATION) Figure 6 shows the circuit diagram for unipolar binary operation. With an ac input, the circuit performs 2-quadrant multiplication. The code table for Figure 6 is given in Table 6. Capacitor C1 provides phase compensation and helps prevent overshoot and ringing when high-speed op amps are used. Binary Number In DAC Register MSB LSB 11 1111 1111 1111 10 0000 0000 0000 00 0000 0000 0001 00 0000 0000 0000 Analog Output, VOUT −VIN(16,383/16,384) −VIN(8192/16,384) = −½VIN −VIN(1/16,384) 0V For zero offset adjustment, the DAC register is loaded with all 0s and amplifier offset (VOS) adjusted so that VOUT is 0 V. Adjusting VOUT to 0 V is not necessary in many applications, but it is recommended that VOS be no greater than (25 × 10−6) (VREF) to maintain specified DAC accuracy (see the Application Hints section). Full-scale trimming is accomplished by loading the DAC register with all 1s and adjusting R1 so that VOUTA = −VIN (16,383/16,384). For high temperature operation, resistors and potentiometers should have a low temperature coefficient. In many applications, because of the excellent gain TC and gain error specifications of the AD7538, gain error trimming is not necessary. In fixed reference applications, full scale can also be adjusted by omitting R1 and R2 and trimming the reference voltage magnitude. Rev. B | Page 10 of 16 AD7538 BIPOLAR OPERATION (4-QUADRANT MULTIPLICATION) Table 7. Bipolar Code Table for the Offset Binary Circuit of Figure 8 The recommended circuit diagram for bipolar operation is shown in Figure 8. Offset binary coding is used. The code table for Figure 8 is given in Table 7. Binary Number In DAC Register MSB LSB 11 1111 1111 1111 10 0000 0000 0001 10 0000 0000 0000 01 1111 1111 1111 00 0000 0000 0000 With the DAC loaded to 10 0000 0000 0000, adjust R1 for VO = 0 V. Alternatively, one can omit R1 and R2 and adjust the ratio of R5 and R6 for VO = 0 V. Full-scale trimming can be accomplished by adjusting the amplitude of VIN or by varying the value of R7. The values given for R1, R2 are the minimum necessary to calibrate the system for Resistors R5, R6, R7 ratio matched to 0.1%. System linearity error is independent of resistor ratio matching and is affected by DAC linearity error only. VDD = 15V VREF = 10V LEAKAGE CURRENT (nA) 60 When operating over a wide temperature range, it is important that the resistors be of the same type so that their temperature coefficients match. LOW LEAKAGE CONFIGURATION For CMOS multiplying DAC, as the device is operated at higher temperatures, the output leakage current increases. For a 14-bit resolution system, this can be a significant source of error. The AD7538 features a leakage reduction configuration to keep the leakage current low over an extended temperature range. One may operate the device with or without this configuration. If VSS (Pin 24) is tied to AGND then the DAC exhibits normal output leakage currents at high temperatures. To use the low leakage facility, VSS should be tied to a voltage of approximately −0.3 V as in Figure 6 and Figure 8. A simple resistor divider (R3, R4) produces approximately −300 mV from −15 V. The C2 capacitor in parallel with R3 is an integral part of the low leakage configuration and must be 4.7 μF or greater. Figure 7 is a plot of leakage current vs. temperature for both conditions. It clearly shows the improvement gained by using the low leakage configuration. Analog Output VOUT +VIN(8191/8192) +VIN(1/8192) 0V −VIN(1/8192) −VIN(8191/8192) 50 40 VSS = 0V 30 20 VSS = –0.3V 10 30 40 50 60 70 80 LDAC R2 22Ω 1 23 2 VREF VDD RFB R6 20kΩ C1 33pF R7 20kΩ 20 LDAC CS 21 CS WR 22 WR A1 AGND 4 DB13 TO DB0 DGND 6 19 INPUT DATA 5 DIGITAL GND R5 10kΩ IOUT 3 AD7538 VSS AD711 R8 5kΩ, 10% C2 4.7µF + 24 R3 1kΩ A2 AD711 VO ANALOG GND R4 47kΩ –15V Figure 8. Bipolar Operation Rev. B | Page 11 of 16 01139-007 VDD 100 110 120 Figure 7. Graph of Typical Leakage Current vs. Temperature for AD7538 VIN R1 50Ω 90 TEMPERATURE (°C) 01139-008 0 AD7538 Substituting this expression into Equation 1 and assuming zero gain error for the DAC (RIN = RFB), the transfer function simplifies to PROGRAMMABLE GAIN AMPLIFIER The circuit shown in Figure 9 provides a programmable gain amplifier (PGA). In it the DAC behaves as a programmable resistance and thus allows the circuit gain to be digitally controlled. VOUT 2n =− VIN N DIGITAL INPUT The ratio N/2n is commonly represented by the term, D, and, as such, is the fractional representation of the digital input word. N IOUT VDD A VREF VOUT A VSS NOTES 1. RESISTOR RFB IS ACTUALLY INCLUDED ON THE DICE. Figure 9. Programmable Gain Amplifier (PGA) 20 log 10 The transfer function of Figure 9 is: Gain = R EQ VOUT =− VIN R FB (1) REQ is the equivalent transfer impedance of the DAC from the VREF pin to the IOUT pin and can be expressed as R EQ = (4) Equation 4 indicates that the gain of the circuit can be varied from 16,384 down to unity (actually 16,384/16,383) in 16,383 steps. The all 0s code is never applied. This avoids an open-loop condition thereby saturating the amplifier. With the all 0s code excluded there remains (2n – 1) possible input codes allowing a choice of (2n – 1) output levels. In decibels the dynamic range is VDD 01139-009 VIN RFB VOUT − 2n − 1 =− = VIN N D AD7538 GND (3) 2 n R IN (2) N where: n is the resolution of the DAC. N is the DAC input code in decimal. RIN is the constant input impedance of the DAC (RIN = RLAD). Rev. B | Page 12 of 16 VOUT V IN = 20 log 10 (2 n − 1) = 84 dB AD7538 APPLICATION HINTS OUTPUT OFFSET CMOS DACs in circuits such as Figure 6 and Figure 8 exhibit a code dependent output resistance, which in turn can cause a code dependent error voltage at the output of the amplifier. The maximum amplitude of this error, which adds to the DAC nonlinearity, depends on VOS, where VOS is the amplifier input offset voltage. To maintain specified accuracy with VREF at 10 V, it is recommended that VOS be no greater than 0.25 mV, or (25 × 10−6) (VREF), over the temperature range of operation. The AD711 is a suitable op amp. The op amp has a wide bandwidth and high slew rate and is recommended for ac and other applications requiring fast settling. In a multiple DAC system, the double buffering of the AD7538 allows the user to simultaneously update all DACs. In Figure 11, a 14-bit word is loaded to the input registers of each of the DACs in sequence. Then, with one instruction to the appropriate address, CS4 (that is, LDAC) is brought low, updating all the DACs simultaneously. ADDRESS BUS 16-BIT LATCH ALE CS1 CS4 CS3 CS2 8096 WR CS AD75381 LDAC WR AD0 TO AD15 GENERAL GROUND MANAGEMENT ADDRESS DECODE DATA BUS Because the AD7538 is specified for high accuracy, it is important to use a proper grounding technique. AC or transient voltages between AGND and DGND can cause noise injection into the analog output. The simplest method of ensuring that voltages at AGND and DGND are equal is to tie AGND and DGND together at the AD7538. In more complex systems where the AGND and DGND intertie on the backplane, it is recommended that two diodes be connected in inverse parallel between the AD7538 AGND and DGND pins (1N914 or equivalent). DB0 TO DB13 CS AD75381 LDAC WR DB0 TO DB13 CS AD75381 MICROPROCESSOR INTERFACING LDAC The AD7538 is designed for easy interfacing to 16-bit microprocessors and can be treated as a memory mapped peripheral. This reduces the amount of external logic needed for interfacing to a minimal. DB0 TO DB13 1LINEAR CIRCUITRY OMITTED FOR CLARITY. 01139-011 WR Figure 11. AD7538-to-8086 Interface: Multiple DAC System AD7538-TO-8086 INTERFACE AD7538-TO-MC68000 INTERFACE Figure 10 shows the 8086 processor interface to a single device. In this setup, the double buffering feature (using LDAC) of the DAC is not used. The 14-bit word is written to the DAC in one MOVE instruction and the analog output responds immediately. Figure 12 shows the MC68000 processor interface to a single device. In this setup, the double buffering feature of the DAC is not used and the appropriate data is written into the DAC in one MOVE instruction. ADDRESS BUS A1 TO A23 16-BIT LATCH ADDRESS DECODE AD75381 AD13 AD0 1LINEAR CIRCUITRY OMITTED FOR CLARITY. AD75381 WR R/W DB0 TO DB13 DATA BUS 01139-010 AD0 TO AD15 D0 TO D15 DATA BUS Figure 10. AD7538-to-8086 Interface Circuit 1LINEAR CIRCUITRY OMITTED FOR CLARITY. Figure 12. AD7538-to-MC68000 Interface Rev. B | Page 13 of 16 CS LDAC DTACK WR WR ADDRESS DECODE AS LDAC 8096 ADDRESS BUS MC68000 CS DB0 TO DB13 01139-012 ALE AD7538 A0 TO A15 The digital inputs to the AD7538 are directly connected to the microprocessor bus in the preceding interface configurations. These inputs are constantly changing even when the device is not selected. The high frequency logic activity on the bus can feed through the DAC package capacitance to show up as noise on the analog output. To minimize this digital feedthrough isolate the DAC from the noise source. Figure 13 shows an interface circuit, which uses this technique. All data inputs are latched from the bus by the CS signal. One may also use other means, such as peripheral interface devices, to reduce the digital feedthrough. ADDRESS DECODE MICROPROCESSOR SYSTEM WR D0 TO D15 1LINEAR AD75381 CS LDAC EN 16-BIT LATCH WR DB0 TO DB13 CIRCUITRY OMITTED FOR CLARITY. Figure 13. AD7538 Interface Circuit Using Latches to Minimize Digital Feedthrough Rev. B | Page 14 of 16 01139-013 DIGITAL FEEDTHROUGH AD7538 OUTLINE DIMENSIONS 1.280 (32.51) 1.250 (31.75) 1.230 (31.24) 24 13 1 12 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.100 (2.54) BSC 0.060 (1.52) MAX 0.210 (5.33) MAX 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.005 (0.13) MIN 0.430 (10.92) MAX 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 071006-A COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 14. 24-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-24-1) Dimensions shown in inches and (millimeters) 0.098 (2.49) MAX 24 13 1 12 PIN 1 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.310 (7.87) 0.220 (5.59) 1.280 (32.51) MAX 0.060 (1.52) 0.015 (0.38) 0.320 (8.13) 0.290 (7.37) 0.150 (3.81) MIN 0.100 (2.54) BSC 0.070 (1.78) SEATING 0.030 (0.76) PLANE 15° 0° 0.015 (0.38) 0.008 (0.20) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 15. 24-Lead Ceramic Dual In-Line Package [CERDIP] (Q-24-1) Dimensions shown in inches and (millimeters) Rev. B | Page 15 of 16 100808-A 0.005 (0.13) MIN AD7538 15.60 (0.6142) 15.20 (0.5984) 13 24 7.60 (0.2992) 7.40 (0.2913) 12 2.65 (0.1043) 2.35 (0.0925) 0.30 (0.0118) 0.10 (0.0039) COPLANARITY 0.10 10.65 (0.4193) 10.00 (0.3937) 1.27 (0.0500) BSC 0.51 (0.0201) 0.31 (0.0122) SEATING PLANE 0.75 (0.0295) 0.25 (0.0098) 45° 8° 0° 1.27 (0.0500) 0.40 (0.0157) 0.33 (0.0130) 0.20 (0.0079) COMPLIANT TO JEDEC STANDARDS MS-013-AD CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 060706-A 1 Figure 16. 24-Lead Standard Small Outline Package [SOIC_W] Wide Body (RW-24) Dimensions shown in millimeters and (inches) ORDERING GUIDE Model AD7538JN AD7538JNZ 1 AD7538KN AD7538KNZ1 AD7538JR AD7538JR-REEL AD7538JRZ1 AD7538JRZ-REEL1 AD7538KR AD7538KR-REEL AD7538KRZ1 AD7538KRZ-REEL1 AD7538AQ AD7538BQ AD7538SQ AD7538TQ 1 Temperature Range 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C −25°C to +85°C −25°C to +85°C −55°C to +125°C −55°C to +125°C Relative Accuracy ±2 LSB ±2 LSB ±1 LSB ±1 LSB ±2 LSB ±2 LSB ±2 LSB ±2 LSB ±1 LSB ±1 LSB ±1 LSB ±1 LSB ±2 LSB ±1 LSB ±2 LSB ±1 LSB Full-Scale Error ±8 LSB ±8 LSB ±5 LSB ±5 LSB ±8 LSB ±8 LSB ±8 LSB ±8 LSB ±5 LSB ±5 LSB ±5 LSB ±5 LSB ±8 LSB ±5 LSB ±10 LSB ±6 LSB Z = RoHS Compliant Part. ©2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D01139-0-1/09(B) Rev. B | Page 16 of 16 Package Description 24-Lead PDIP 24-Lead PDIP 24-Lead PDIP 24-Lead PDIP 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead SOIC_W 24-Lead CERDIP 24-Lead CERDIP 24-Lead CERDIP 24-Lead CERDIP Package Option N-24-1 N-24-1 N-24-1 N-24-1 RW-24 RW-24 RW-24 RW-24 RW-24 RW-24 RW-24 RW-24 Q-24-1 Q-24-1 Q-24-1 Q-24-1