380CV25 CY7C1380CV25 CY7C1382CV25 PRELIMINARY 512K x 36/1M x 18 Pipelined SRAM Features • • • • • • • • • • • Fast clock speed: 250, 225, 200, 167 MHz Provide high-performance 3-1-1-1 access rate Fast OE access times: 2.6, 2.8, 3.0, 3.4 ns Optimal for depth expansion Single 2.5V ±5% power supply Common data inputs and data outputs Byte Write Enable and Global Write control Chip enable for address pipeline Address, data, and control registers Internally self-timed Write cycle Burst control pins (interleaved or linear burst sequence) • Automatic power-down available using ZZ mode or CE deselect • Available in 119-ball bump BGA, 165-ball FBGA and 100-pin TQFP packages • JTAG boundary scan for BGA packaging version Functional Description The Cypress Synchronous Burst SRAM family employs highspeed, low-power CMOS designs using advanced single-layer polysilicon, triple-layer metal technology. Each memory cell consists of six transistors. The CY7C1382CV25 and CY7C1380CV25 SRAMs integrate 1,048,576x18 and 524,288x36 SRAM cells with advanced synchronous peripheral circuitry and a 2-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive-edge-triggered clock input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining chip enable (CE), burst control inputs (ADSC, ADSP, and ADV), write enables (BWa, BWb, BWc, BWd and BWE), and global write (GW). Asynchronous inputs include the output enable (OE) and burst mode control (MODE). The data (DQa,b,c,d) and the data parity (DQPa,b,c,d) outputs, enabled by OE, are also asynchronous. DQa,b,c,d and DPa,b,c,d apply to CY7C1380CV25 and DQa,b and DPa,b apply to CY7C1382CV25. a, b, c, d each are of 8 bits wide in the case of DQ and 1 bit wide in the case of DP. Addresses and chip enables are registered with either address status processor (ADSP) or address status controller (ADSC) input pins. Subsequent burst addresses can be internally generated as controlled by the burst advance pin (ADV). Address, data inputs, and write controls are registered on-chip to initiate self-timed Write cycle. Write cycles can be one to four bytes wide as controlled by the write control inputs. Individual byte write allows individual byte to be written. BWa controls DQa and DPa. BWb controls DQb and DPb. BWc controls DQc and DPd. BWd controls DQd and DPd. BWa, BWb BWc, and BWd can be active only with BWE being LOW. GW being LOW causes all bytes to be written. Write pass-through capability allows written data available at the output for the next Read cycle. This device also incorporates pipelined enable circuit for easy depth expansion without penalizing system performance. All inputs and outputs of the CY7C1380CV25 and the CY7C1382CV25 are JEDEC standard JESD8-5 compatible. Selection Guide 250 MHz 225 MHz 200 MHz 167 MHz Unit Maximum Access Time 2.6 2.8 3.0 3.4 ns Maximum Operating Current 350 325 300 275 mA Maximum CMOS Standby Current 70 70 70 70 mA Shaded areas contain advance information. Cypress Semiconductor Corporation Document #: 38-05240 Rev. *A • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised November 20, 2002 CY7C1380CV25 CY7C1382CV25 PRELIMINARY CY7C1380CV25 - 512K x 36 MODE (A[1;0]) 2 BURST Q0 CE COUNTER Q1 CLR CLK ADV ADSC ADSP Q A[18:0] 19 GW 17 DQd, DPd BYTEWRITE REGISTERS DQc, DPc BYTEWRITE REGISTERS Q D DQb, DPb BYTEWRITE REGISTERS Q D DQa, DPa BYTEWRITE REGISTERS Q D BWE BW d D BWc BWb BWa CE1 CE2 CE3 D ENABLE CE REGISTER 19 17 ADDRESS CE REGISTER D 512KX36 MEMORY ARRAY Q 36 36 Q D ENABLE DELAY Q REGISTER INPUT REGISTERS CLK OUTPUT REGISTERS CLK OE SLEEP CONTROL ZZ DQa,b,c,d DPa,b CY7C1382CV25 - 1M X 18 MODE (A[1;0]) 2 BURST Q0 CE COUNTER Q1 CLR CLK ADV ADSC ADSP A[19:0] GW Q 20 BWE BW b 18 DQb, DPb BYTEWRITE REGISTERS DQa, DPa BYTEWRITE REGISTERS Q D ENABLE CE CE REGISTER Q D D BWa CE1 CE2 CE3 ADDRESS CE REGISTER D 18 20 1M X 18 MEMORY ARRAY Q 18 D ENABLE DELAY Q REGISTER OUTPUT REGISTERS CLK 18 INPUT REGISTERS CLK OE ZZ SLEEP CONTROL DQa,b DPa,b Document #: 38-05240 Rev. *A Page 2 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Pin Configurations NC NC NC VDDQ VSSQ NC NC DQb DQb VSSQ VDDQ DQb DQb NC VDD NC VSS DQb DQb VDDQ VSSQ DQb DQb DPb NC VSSQ VDDQ NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CY7C1382CV25 (1M x 18) MODE A A A A A1 A0 NC NC VSS VDD MODE A A A A A1 A0 NC NC VSS VDD A A A A A A A A A NC,DQPb DQb DQb VDDQ VSSQ DQb DQb DQb DQb VSSQ VDDQ DQb DQb VSS NC VDD ZZ DQa DQa VDDQ VSSQ DQa DQa DQa DQa VSSQ VDDQ DQa DQa NC,DQPa Document #: 38-05240 Rev. *A 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A NC NC VDDQ VSSQ NC DPa DQa DQa VSSQ VDDQ DQa DQa VSS NC VDD ZZ DQa DQa VDDQ VSSQ DQa DQa NC NC VSSQ VDDQ NC NC NC A A A A A A A A A CY7C1380CV25 (512K X 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NC,DQPc DQc DQc VDDQ VSSQ DQc DQc DQc DQc VSSQ VDDQ DQc DQc NC VDD NC VSS DQd DQd VDDQ VSSQ DQd DQd DQd DQd VSSQ VDDQ DQd DQd NC,DQPd 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 NC NC BWb BWa CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 BWd BWc BWb BWa CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100-Pin TQFP Top View Page 3 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Pin Configurations (continued) 119-Ball BGA CY7C1380CV25 (512K x 36) 1 2 3 4 5 6 7 A VDDQ A A A A A A C NC NC ADSP ADSC VDDQ B A A VDD D E DQc DQc A DQPc DQc A VSS VSS NC A VSS A DQPb CE1 VSS OE ADV GW VDD VSS BWb VSS DQb DQb F VDDQ DQc VSS G H J DQc DQc VDDQ K DQd BWc VSS NC VSS L M DQc DQc VDD DQd DQd VDDQ N DQd DQd DQd DQd DQb DQb DQb VDD VDDQ DQb DQb VDDQ DQa DQa DQb NC VSS NC NC BWd VSS CLK NC BWa DQa DQa BWE VSS DQa VSS A1 VSS DQa VDDQ DQa A0 VDD VSS DQPa DQa A A NC A 36M NC ZZ TCK TDO NC VDDQ P DQd DQPd VSS R NC T NC A 72M MODE A U VDDQ TMS TDI CY7C1382CV25 (1M x 18) 1 A VDDQ B NC NC 2 3 4 5 6 7 A A A A VDDQ NC A VSS CE1 VSS VSS VSS VSS A DQPa NC DQa A A A ADSP A A ADSC VDD VSS VSS VSS C D DQb E NC A NC DQb F VDDQ NC DQa VDD NC DQa DQa NC VSS NC VSS DQa VDDQ NC VSS NC DQa 36M NC A A A NC ZZ TCK TDO NC VDDQ DQb NC VDD DQb NC BWb VSS NC VSS VSS CLK NC BWa DQb NC VSS VSS BWE DQb A1 P NC DQPb VSS R NC T 72M A A MODE A A0 VDD U VDDQ TMS TDI VDDQ K NC L M VDDQ N Document #: 38-05240 Rev. *A NC DQb DQb NC DQa VDDQ DQa NC VDDQ OE ADV GW VDD G H J NC NC NC VSS NC Page 4 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Pin Configurations (continued) 165-Ball Bump FBGA CY7C1380CV25 (512K x 36) - 11 x 15 FBGA 1 2 3 4 5 6 7 8 9 10 11 A NC A CE1 BWc BWb CE3 BWE ADSC ADV A NC B C D E F G H J K L M N P NC DPc A NC CE2 VDDQ BWd VSS BWa VSS CLK VSS GW VSS OE VSS ADSP VDDQ A NC 144M DPb DQb R DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb NC DQd VSS DQd NC VDDQ VDD VDD VSS VSS VSS VSS VSS VSS VDD VDD NC VDDQ NC DQa ZZ DQa DQd DQd DQd DQd VDDQ VDDQ VDD VDD VSS VSS VSS VSS VSS VSS VDD VDD VDDQ VDDQ DQa DQa DQa DQa DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa DPd NC VDDQ VSS NC A VSS VSS VDDQ NC DPa NC 72M A A TDI A1 TDO A A A A MODE 36M A A TMS A0 TCK A A A A 11 CY7C1382CV25 (1M x 18) - 11 x 15 FBGA 1 2 3 4 5 6 7 8 9 10 A NC A CE1 BWb NC CE3 BWE ADSC ADV A A B C D E F G H J K L M N P NC NC A NC CE2 VDDQ NC VSS BWa VSS CLK VSS GW VSS OE VSS ADSP VDDQ A NC 144M DPa NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC DQb VSS NC NC VDDQ VDD VDD VSS VSS VSS VSS VSS VSS VDD VDD NC VDDQ NC DQa ZZ NC DQb DQb NC NC VDDQ VDDQ VDD VDD VSS VSS VSS VSS VSS VSS VDD VDD VDDQ VDDQ DQa DQa NC NC DQb NC VDDQ VDD VSS VSS VSS VDD VDDQ DQa NC DPb NC VDDQ VSS NC A VSS VSS VDDQ NC NC NC 72M A A TDI A1 TDO A A A A MODE 36M A A TMS A0 TCK A A A A R Document #: 38-05240 Rev. *A Page 5 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Pin Definitions Name I/O Description A0 A1 A InputSynchronous Address Inputs used to select one of the address locations. Sampled at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A[1:0] feed the 2-bit counter. BWa BWb BWc BWd InputSynchronous Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM. Sampled on the rising edge of CLK. GW InputSynchronous Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global write is conducted (ALL bytes are written, regardless of the values on BWa,b,c,d and BWE). BWE InputSynchronous Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be asserted LOW to conduct a byte write. CLK Input-Clock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. CE1 InputSynchronous Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE2 InputSynchronous Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE3 to select/deselect the device. (TQFP Only) CE3 InputSynchronous Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. (TQFP Only) OE InputAsynchronous Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV InputSynchronous Advance Input signal, sampled on the rising edge of CLK. When asserted, it automatically increments the address in a burst cycle. ADSP InputSynchronous Address Strobe from Processor, sampled on the rising edge of CLK. When asserted LOW, A is captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC InputSynchronous Address Strobe from Controller, sampled on the rising edge of CLK. When asserted LOW, A[x:0] is captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. MODE Input-Pin Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDDQ or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. ZZ InputAsynchronous ZZ “sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition with data integrity preserved. DQa, DPa DQb, DPb DQc, DPc DQd, DPd I/OSynchronous Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by A[X] during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQx and DPx are placed in a three-state condition. DQ a,b,c, and d are 8 bits wide and the DP a,b,c, and d are 1 bit wide. TDO JTAG serial output Synchronous Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. (BGA Only) TDI JTAG serial input Synchronous Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK.(BGA Only) Document #: 38-05240 Rev. *A Page 6 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Pin Definitions Name I/O Description TMS Test Mode Select Synchronous This pin controls the Test Access Port state machine. Sampled on the rising edge of TCK. (BGA Only) TCK JTAG serial clock Serial clock to the JTAG circuit. (BGA Only) VDD Power Supply VSS Ground VDDQ I/O Power Supply VSSQ I/O Ground Power supply inputs to the core of the device. Should be connected to 2.5V ± 5% power supply. Ground for the core of the device. Should be connected to ground of the system. Power supply for the I/O circuitry. Ground for the I/O circuitry. Should be connected to ground of the system. NC - No Connects.Pins are not internally connected. 36M 72M 144M - No Connects. Reserved for address expansion. Document #: 38-05240 Rev. *A Page 7 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Introduction (GW, BWE, and BWx) and ADV inputs are ignored during this first cycle. Functional Overview ADSP triggered write accesses require two clock cycles to complete. If GW is asserted LOW on the second clock rise, the data presented to the DQx inputs is written into the corresponding address location in the RAM core. If GW is HIGH, then the write operation is controlled by BWE and BWx signals. The CY7C1380CV25/CY7C1382CV25 provides byte write capability that is described in the write cycle description table. Asserting the Byte Write Enable input (BWE) with the selected Byte Write (BWa,b,c,d for CY7C1380CV25 and BWa,b for CY7C1382CV25) input will selectively write to only the desired bytes. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (tCO) is 2.6 ns (250-MHz device). The CY7C1380CV25/CY7C1382CV25 supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium® and i486 processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the Processor Address Strobe (ADSP) or the Controller Address Strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte write operations are qualified with the Byte Write Enable (BWE) and Byte Write Select (BWa,b,c,d for CY7C1380V25 and BWa,b for CY7C1382V25) inputs. A Global Write Enable (GW) overrides all byte write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self-timed write circuitry. Synchronous Chip Selects (CE1, CE2, CE3 for TQFP / CE1 for BGA) and an asynchronous Output Enable (OE) provide for easy bank selection and output three-state control. ADSP is ignored if CE1 is HIGH. Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2) chip selects are all asserted active, and (3) the write signals (GW, BWE) are all deasserted HIGH. ADSP is ignored if CE1 is HIGH. The address presented to the address inputs is stored into the address advancement logic and the Address Register while being presented to the memory core. The corresponding data is allowed to propagate to the input of the Output Registers. At the rising edge of the next clock the data is allowed to propagate through the output register and onto the data bus within 2.6 ns (250-MHz device) if OE is active LOW. The only exception occurs when the SRAM is emerging from a deselected state to a selected state, its outputs are always three-stated during the first cycle of the access. After the first cycle of the access, the outputs are controlled by the OE signal. Consecutive single read cycles are supported. Once the SRAM is deselected at clock rise by the chip select and either ADSP or ADSC signals, its output will three-state immediately. Single Write Accesses Initiated by ADSP This access is initiated when both of the following conditions are satisfied at clock rise: (1) ADSP is asserted LOW, and (2) chip select is asserted active. The address presented is loaded into the address register and the address advancement logic while being delivered to the RAM core. The write signals Document #: 38-05240 Rev. *A Because the CY7C1380CV25/CY7C1382CV25 is a common I/O device, the output enable (OE) must be deasserted HIGH before presenting data to the DQ inputs. Doing so will threestate the output drivers. As a safety precaution, DQ are automatically three-stated whenever a write cycle is detected, regardless of the state of OE. Single Write Accesses Initiated by ADSC ADSC write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted HIGH, (3) chip select is asserted active, and (4) the appropriate combination of the write inputs (GW, BWE, and BWx) are asserted active to conduct a write to the desired byte(s). ADSC triggered write accesses require a single clock cycle to complete. The address presented to A[17:0] is loaded into the address register and the address advancement logic while being delivered to the RAM core. The ADV input is ignored during this cycle. If a global write is conducted, the data presented to the DQ[x:0] is written into the corresponding address location in the RAM core. If a byte write is conducted, only the selected bytes are written. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. Because the CY7C1380CV25/CY7C1382CV25 is a common I/O device, the output enable (OE) must be deasserted HIGH before presenting data to the DQ[x:0] inputs. Doing so will three-state the output drivers. As a safety precaution, DQ[x:0] are automatically three-stated whenever a write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1380CV25/CY7C1382CV25 provides a two-bit wraparound counter, fed by A[1:0], that implements either an interleaved or linear burst sequence. The interleaved burst sequence is designed specifically to support Intel® Pentium applications. The linear burst sequence is designed to support processors that follow a linear burst sequence. The burst sequence is user selectable through the MODE input. Asserting ADV LOW at clock rise will automatically increment the burst counter to the next address in the burst sequence. Both read and write burst operations are supported. Page 8 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Sleep Mode Interleaved Burst Sequence First Address Second Address Third Address Fourth Address A[1:0]] A[1:0] A[1:0] A[1:0] 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00 The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CEs, ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Linear Burst Sequence First Address Second Address Third Address Fourth Address A[1:0] A[1:0] A[1:0] A[1:0] 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 ZZ Mode Electrical Characteristics Parameter Description Test Conditions IDDZZ Sleep mode standby current tZZS tZZREC Max. Unit ZZ > VDD − 0.2V 60 mA Device operation to ZZ ZZ > VDD − 0.2V 2tCYC ns ZZ recovery time ZZ < 0.2V Document #: 38-05240 Rev. *A Min. 2tCYC ns Page 9 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Cycle Descriptions[1, 2, 3, 4] Next Cycle Add. Used ZZ CE3 CE2 CE1 ADSP ADSC ADV OE DQ Write Unselected None 0 X X 1 X 0 X X Hi-Z X Unselected None 0 1 X 0 0 X X X Hi-Z X Unselected None 0 X 0 0 0 X X X Hi-Z X Unselected None 0 1 X 0 1 0 X X Hi-Z X Unselected None 0 X 0 0 1 0 X X Hi-Z X Begin Read External 0 0 1 0 0 X X X Hi-Z X Begin Read External 0 0 1 0 1 0 X X Hi-Z Read Continue Read Next 0 X X X 1 1 0 1 Hi-Z Read Continue Read Next 0 X X X 1 1 0 0 DQ Read Continue Read Next 0 X X 1 X 1 0 1 Hi-Z Read Continue Read Next 0 X X 1 X 1 0 0 DQ Read Suspend Read Current 0 X X X 1 1 1 1 Hi-Z Read Suspend Read Current 0 X X X 1 1 1 0 DQ Read Suspend Read Current 0 X X 1 X 1 1 1 Hi-Z Read Suspend Read Current 0 X X 1 X 1 1 0 DQ Read Begin Write Current 0 X X X 1 1 1 X Hi-Z Write Begin Write Current 0 X X 1 X 1 1 X Hi-Z Write Begin Write External 0 0 1 0 1 0 X X Hi-Z Write Continue Write Next 0 X X X 1 1 0 X Hi-Z Write Continue Write Next 0 X X 1 X 1 0 X Hi-Z Write Suspend Write Current 0 X X X 1 1 1 X Hi-Z Write Suspend Write Current 0 X X 1 X 1 1 X Hi-Z Write ZZ “sleep” None 1 X X X X X X X Hi-Z X Notes: 1. X = “Don't Care,” 1 = HIGH, 0 = LOW. 2. Write is defined by BWE, BWx, and GW. See Write Cycle Descriptions table. 3. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 4. CE1, CE2 and CE3 are available only in the TQFP package. The BGA package has a single chip select, CE1. Document #: 38-05240 Rev. *A Page 10 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Write Cycle Descriptions[1, 5, 6] Function (1380CV25) GW BWE BWd BWc BWb BWa Read 1 1 X X X X Read 1 0 1 1 1 1 Write Byte 0 – DQa 1 0 1 1 1 0 Write Byte 1 – DQb 1 0 1 1 0 1 Write Bytes 1, 0 1 0 1 1 0 0 Write Byte 2 – DQc 1 0 1 0 1 1 Write Bytes 2, 0 1 0 1 0 1 0 Write Bytes 2, 1 1 0 1 0 0 1 Write Bytes 2, 1, 0 1 0 1 0 0 0 Write Byte 3 – DQd 1 0 0 1 1 1 Write Bytes 3, 0 1 0 0 1 1 0 Write Bytes 3, 1 1 0 0 1 0 1 Write Bytes 3, 1, 0 1 0 0 1 0 0 Write Bytes 3, 2 1 0 0 0 1 1 Write Bytes 3, 2, 0 1 0 0 0 1 0 Write Bytes 3, 2, 1 1 0 0 0 0 1 Write All Bytes 1 0 0 0 0 0 Write All Bytes 0 X X X X X Function (1382CV25) GW BWE BWb BWa Read 1 1 X X Read 1 0 1 1 Write Byte 0 – DQ[7:0] and DP0 1 0 1 0 Write Byte 1 – DQ[15:8] and DP1 1 0 0 1 Write All Bytes 1 0 0 0 Write All Bytes 0 X X X Notes: 5. The SRAM always initiates a read cycle when ADSP asserted, regardless of the state of GW, BWE, or BWx. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to three-state. OE is a “don't care” for the remainder of the write cycle. 6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQ = High-Z when OE is inactive or when the device is deselected, and DQ = data when OE is active. Document #: 38-05240 Rev. *A Page 11 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY IEEE 1149.1 Serial Boundary Scan (JTAG) The CY7C1380CV25/CY7C1382CV25 incorporates a serial boundary scan Test Access Port (TAP) in the BGA package only. The TQFP package does not offer this functionality. This port operates in accordance with IEEE Standard 1149.1-1900, but does not have the set of functions required for full 1149.1 compliance. These functions from the IEEE specification are excluded because their inclusion places an added delay in the critical speed path of the SRAM. Note that the TAP controller functions in a manner that does not conflict with the operation of other devices using 1149.1 fully compliant TAPs. The TAP operates using JEDEC standard 2.5V I/O logic levels. Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull-up resistor. TDO should be left unconnected. Upon power-up, the device will come up in a reset state which will not interfere with the operation of the device. Test Access Port (TAP)—Test Clock The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Test Mode Select The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this pin unconnected if the TAP is not used. The pin is pulled up internally, resulting in a logic HIGH level. Test Data-In (TDI) The TDI pin is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see the TAP Controller State Diagram. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the Most Significant Bit (MSB) on any register. Test Data Out (TDO) ry. Only one register can be selected at a time through the instruction registers. Data is serially loaded into the TDI pin on the rising edge of TCK. Data is output on the TDO pin on the falling edge of TCK. Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO pins as shown in the TAP Controller Block Diagram. Upon power-up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the CaptureIR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board level serial test path. Bypass Register To save time when serially shifting data through registers, it is sometimes advantageous to skip certain states. The bypass register is a single-bit register that can be placed between TDI and TDO pins. This allows data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. Boundary Scan Register The boundary scan register is connected to all the input and output pins on the SRAM. Several no connect (NC) pins are also included in the scan register to reserve pins for higher density devices. The x36 configuration has a 70-bit-long register, and the x18 configuration has a 51-bit-long register. The boundary scan register is loaded with the contents of the RAM Input and Output ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO pins when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the Input and Output ring. The Boundary Scan Order tables show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO. Identification (ID) Register The TDO output pin is used to serially clock data-out from the registers. The e output is active depending upon the current state of the TAP state machine (see TAP Controller State Diagram). The output changes on the falling edge of TCK. TDO is connected to the Least Significant Bit (LSB) of any register. The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions table. Performing a TAP Reset TAP Instruction Set A Reset is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power-up, the TAP is reset internally to ensure that TDO comes up in a high-Z state. Eight different instructions are possible with the three-bit instruction register. All combinations are listed in the Instruction Code table. Three of these instructions are listed as RESERVED and should not be used. The other five instructions are described in detail below. TAP Registers The TAP controller used in this SRAM is not fully compliant to the 1149.1 convention because some of the mandatory 1149.1 instructions are not fully implemented. The TAP controller cannot be used to load address, data or control signals into the Registers are connected between the TDI and TDO pins and allow data to be scanned into and out of the SRAM test circuitDocument #: 38-05240 Rev. *A Page 12 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY SRAM and cannot preload the Input or Output buffers. The SRAM does not implement the 1149.1 commands EXTEST or INTEST or the PRELOAD portion of SAMPLE/PRELOAD; rather it performs a capture of the Inputs and Output ring when these instructions are executed. Instructions are loaded into the TAP controller during the ShiftIR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO pins. To execute the instruction once it is shifted in, the TAP controller needs to be moved into the Update-IR state. EXTEST EXTEST is a mandatory 1149.1 instruction which is to be executed whenever the instruction register is loaded with all 0s. EXTEST is not implemented in the TAP controller, and therefore this device is not compliant to the 1149.1 standard. The TAP controller does recognize an all-0 instruction. When an EXTEST instruction is loaded into the instruction register, the SRAM responds as if a SAMPLE/PRELOAD instruction has been loaded. There is one difference between the two instructions. Unlike the SAMPLE/PRELOAD instruction, EXTEST places the SRAM outputs in a High-Z state. IDCODE The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO pins and allows the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power-up or whenever the TAP controller is given a test logic reset state. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO pins when the TAP controller is in a Shift-DR state. It also places all SRAM outputs into a High-Z state. SAMPLE/PRELOAD SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The PRELOAD portion of this instruction is not implemented, so the TAP controller is not fully 1149.1 compliant. Document #: 38-05240 Rev. *A When the SAMPLE/PRELOAD instruction is loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the inputs and output pins is captured in the boundary scan register. The user must be aware that the TAP controller clock can only operate at a frequency up to 10 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output will undergo a transition. The TAP may then try to capture a signal while in transition (metastable state). This will not harm the device, but there is no guarantee as to the value that will be captured. Repeatable results may not be possible. To guarantee that the boundary scan register will capture the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller’s capture set-up plus hold times (tCS and tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is still possible to capture all other signals and simply ignore the value of the CK and CK captured in the boundary scan register. Once the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins. Note that since the PRELOAD part of the command is not implemented, putting the TAP into the Update to the UpdateDR state while performing a SAMPLE/PRELOAD instruction will have the same effect as the Pause-DR command. Bypass When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO pins. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. Page 13 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY TAP Controller State Diagram 1 TEST-LOGIC RESET 0 TEST-LOGIC/ IDLE 1 1 1 SELECT DR-SCAN SELECT IR-SCAN 0 0 1 1 CAPTURE-DR CAPTURE-DR 0 0 0 SHIFT-DR 0 SHIFT-IR 1 1 1 EXIT1-DR 1 EXIT1-IR 0 0 PAUSE-DR 0 0 PAUSE-IR 1 1 0 0 EXIT2-DR EXIT2-IR 1 1 UPDATE-DR 1 0 UPDATE-IR 1 0 Note: The 0/1 next to each state represents the value at TMS at the rising edge of TCK. Document #: 38-05240 Rev. *A Page 14 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY TAP Controller Block Diagram 0 Bypass Register Selection Circuitry 2 TDI 1 0 1 0 1 0 Selection Circuitry TDO Instruction Register 31 30 29 . . 2 Identification Register x . . . . 2 Boundary Scan Register TCK TAP Controller TMS TAP Electrical Characteristics Over the Operating Range[7, 8] Parameter Description Test Conditions Min. Max. Unit VOH1 Output HIGH Voltage IOH = −1.0 mA 1.7 V VOH2 Output HIGH Voltage IOH = −100 µA 2.1 V VOL1 Output LOW Voltage IOL = 1.0 mA 0.4 V VOL2 Output LOW Voltage IOL = 100 µA 0.2 V VIH Input HIGH Voltage 1.7 VDD + 0.3 V VIL Input LOW Voltage −0.3 0.7 V IX Input Load Current −5 5 µA GND < VI < VDDQ Notes: 7. All Voltage referenced to Ground. 8. Overshoot: VIH(AC) < VDD+1.5V for t < tTCYC/2, Undershoot: VIL(AC) > −0.5V for t < tTCYC/2. Document #: 38-05240 Rev. *A Page 15 of 33 PRELIMINARY CY7C1380CV25 CY7C1382CV25 TAP AC Switching Characteristics Over the Operating Range[9, 10] Parameters Description Min. Max Unit 10 MHz tTCYC TCK Clock Cycle Time tTF TCK Clock Frequency 100 ns tTH TCK Clock HIGH 40 ns tTL TCK Clock LOW 40 ns tTMSS TMS Set-up to TCK Clock Rise 10 ns tTDIS TDI Set-up to TCK Clock Rise 10 ns tCS Capture Set-up to TCK Rise 10 ns tTMSH TMS Hold after TCK Clock Rise 10 ns tTDIH TDI Hold after Clock Rise 10 ns tCH Capture Hold after Clock Rise 10 ns Set-up Times Hold Times Output Times tTDOV TCK Clock LOW to TDO Valid tTDOX TCK Clock LOW to TDO Invalid 20 0 ns ns Notes: 9. tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register. 10. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 V/ns. Document #: 38-05240 Rev. *A Page 16 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY TAP Timing and Test Conditions 1.25V 50Ω ALL INPUT PULSES TDO 2.5V Z0 = 50Ω 1.25V CL = 20 pF 0V GND (a) tTH tTL Test Clock TCK tTCYC tTMSS tTMSH Test Mode Select TMS tTDIS tTDIH Test Data-In TDI Test Data-Out TDO tTDOV Document #: 38-05240 Rev. *A tTDOX Page 17 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Identification Register Definitions Instruction Field 512K x 36 1M x 18 Revision Number (31:28) 0100 0100 Reserved for version number Cypress Device ID (27:24) 1011 1011 Reserved for internal use Device Type (23:18) 000000 000000 Defines memory type and architecture Device Width and Density (17:12) 100101 010101 Defines width and density 000001101001 000001101001 Cypress JEDEC ID (11:0) Description Allows unique identification of SRAM vendor Scan Register Sizes Register Name Bit Size (x18) Bit Size (x36) Instruction 3 3 Bypass 1 1 ID 32 32 Boundary Scan 51 70 Identification Codes Instruction Code Description EXTEST 000 Captures the Input/Output ring contents. Places the boundary scan register between the TDI and TDO. Forces all SRAM outputs to High-Z state. This instruction is not 1149.1 compliant. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operation. SAMPLE Z 010 Captures the Input/Output contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a High-Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures the Input/Output ring contents. Places the boundary scan register between TDI and TDO. Does not affect the SRAM operation. This instruction does not implement 1149.1 preload function and is therefore not 1149.1 compliant. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operation. Document #: 38-05240 Rev. *A Page 18 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Boundary Scan Order (512K x 36) Bit # Signal Name Bump ID Bit # Signal Name Boundary Scan Order (1M x 18) Bump ID Bit # Signal Name Bump ID Bit # Signal Name Bump ID 1 TBD TBD 36 TBD TBD 1 TBD TBD 36 TBD TBD 2 TBD TBD 37 TBD TBD 2 TBD TBD 37 TBD TBD 3 TBD TBD 38 TBD TBD 3 TBD TBD 38 TBD TBD 4 TBD TBD 39 TBD TBD 4 TBD TBD 39 TBD TBD 5 TBD TBD 40 TBD TBD 5 TBD TBD 40 TBD TBD 6 TBD TBD 41 TBD TBD 6 TBD TBD 41 TBD TBD 7 TBD TBD 42 TBD TBD 7 TBD TBD 42 TBD TBD 8 TBD TBD 43 TBD TBD 8 TBD TBD 43 TBD TBD 9 TBD TBD 44 TBD TBD 9 TBD TBD 44 TBD TBD 10 TBD TBD 45 TBD TBD 10 TBD TBD 45 TBD TBD 11 TBD TBD 46 TBD TBD 11 TBD TBD 46 TBD TBD 12 TBD TBD 47 TBD TBD 12 TBD TBD 47 TBD TBD 13 TBD TBD 48 TBD TBD 13 TBD TBD 48 TBD TBD 14 TBD TBD 49 TBD TBD 14 TBD TBD 49 TBD TBD 15 TBD TBD 50 TBD TBD 15 TBD TBD 50 TBD TBD 16 TBD TBD 51 TBD TBD 16 TBD TBD 51 TBD TBD 17 TBD TBD 52 TBD TBD 17 TBD TBD 52 TBD TBD 18 TBD TBD 53 TBD TBD 18 TBD TBD 53 TBD TBD 19 TBD TBD 54 TBD TBD 19 TBD TBD 54 TBD TBD 20 TBD TBD 55 TBD TBD 20 TBD TBD 55 TBD TBD 21 TBD TBD 56 TBD TBD 21 TBD TBD 56 TBD TBD 22 TBD TBD 57 TBD TBD 22 TBD TBD 57 TBD TBD 23 TBD TBD 58 TBD TBD 23 TBD TBD 58 TBD TBD 24 TBD TBD 59 TBD TBD 24 TBD TBD 59 TBD TBD 25 TBD TBD 60 TBD TBD 25 TBD TBD 60 TBD TBD 26 TBD TBD 61 TBD TBD 26 TBD TBD 61 TBD TBD 27 TBD TBD 62 TBD TBD 27 TBD TBD 62 TBD TBD 28 TBD TBD 63 TBD TBD 28 TBD TBD 63 TBD TBD 29 TBD TBD 64 TBD TBD 29 TBD TBD 64 TBD TBD 30 TBD TBD 65 TBD TBD 30 TBD TBD 65 TBD TBD 31 TBD TBD 66 TBD TBD 31 TBD TBD 66 TBD TBD 32 TBD TBD 67 TBD TBD 32 TBD TBD 67 TBD TBD 33 TBD TBD 68 TBD TBD 33 TBD TBD 68 TBD TBD 34 TBD TBD 69 TBD TBD 34 TBD TBD 69 TBD TBD 35 TBD TBD 70 TBD TBD 35 TBD TBD 70 TBD TBD Document #: 38-05240 Rev. *A Page 19 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –55°C to +150°C Ambient Temperature with Power Applied............................................. –55°C to +125°C Supply Voltage on VDD Relative to GND ....... –0.3V to +3.6V DC Voltage Applied to Outputs in High Z State[11] ................................ –0.5V to VDDQ + 0.5V DC Input Voltage[11] ............................ –0.5V to VDDQ + 0.5V Current into Outputs (LOW) .........................................20 mA Static Discharge Voltage........................................... >2001V (per MIL-STD-883, Method 3015) Latch-Up Current.................................................... >200 mA Operating Range Range Com’l Ind’l Ambient Temp.[12] VDD/VDDQ 0°C to 70°C 2.5V ± 5% –40°C to +85°C Electrical Characteristics Over the Operating Range Parameter VDD/VDDQ Description Test Conditions Power Supply Voltage Min. Max. Unit 2.375 2.625 V VOH Output HIGH Voltage VDD = Min., IOH = −1.0 mA VOL Output LOW Voltage VDD = Min., IOL = 1.0 mA VIH Input HIGH Voltage 1.7 VDD + 0.3 VIL Input LOW Voltage[11] –0.3 0.7 IX Input Load Current except ZZ and MODE –5 5 µA IZZ Input Current of MODE 2.0 V 0.4 GND < VI < VDDQ −30 30 µA Input Current of ZZ Input = VSS −30 30 µA IOZ Output Leakage Current GND < VI < VDDQ, Output Disabled –5 5 µA IDD VDD Operating Supply VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC 4.0-ns cycle, 250 MHz 350 mA 4.4-ns cycle, 225 MHz 325 mA 5.0-ns cycle, 200 MHz 300 mA 6.0-ns cycle, 167 MHz 275 mA 4.0-ns cycle, 250 MHz 120 mA 4.4-ns cycle, 225 MHz 110 mA 5.0-ns cycle, 200 MHz 100 mA 6.0-ns cycle, 167 MHz 90 mA All speed grades 70 mA ISB1 Automatic CE PowerMax. VDD, Device Deselected, Down Current—TTL Inputs VIN > VIH or VIN < VIL f = fMAX = 1/tCYC ISB2 Automatic CE PowerDown Current—CMOS Inputs Max. VDD, Device Deselected, VIN < 0.3V or VIN > VDDQ – 0.3V, f=0 ISB3 Automatic CE PowerDown Current—CMOS Inputs Max. VDD, Device Deselected, or 4.0-ns cycle, 250 MHz VIN < 0.3V or VIN > VDDQ – 0.3V 4.4-ns cycle, 225 MHz f = fMAX = 1/tCYC 5.0-ns cycle, 200 MHz 105 mA 100 mA 95 mA 6.0-ns cycle, 167 MHz 85 mA All Speeds 80 mA ISB4 Automatic CE PowerMax. VDD, Device Deselected, Down Current—TTL Inputs VIN > VIH or VIN < VIL, f = 0 Shaded areas contain advance information. Notes: 11. Minimum voltage equals –2.0V for pulse durations of less than 20 ns. 12. TA is the temperature. Document #: 38-05240 Rev. *A Page 20 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Capacitance[13] Max. Parameter Description CIN Input Capacitance CCLK CI/O Test Conditions TA = 25°C, f = 1 MHz 100-TQFP 119-BGA 165-FBGA Unit TBD TBD TBD pF Clock Input Capacitance TBD TBD TBD pF Input/Output Capacitance TBD TBD TBD pF AC Test Loads and Waveforms[14] R = 1667Ω VDDQ OUTPUT ALL INPUT PULSES OUTPUT Z0 = 50Ω Rt = 50Ω 2.5V 10% 5 pF Vt - Termination Voltage (a) Rt - Termination Resistance INCLUDING JIG AND SCOPE 90% 10% 90% GND R = 1538Ω ≤ 1 ns 30 pF Vt = 1.25 [10] ≤ 1 ns (c) (b) Thermal Resistance[13] Description Thermal Resistance (Junction to Ambient) Thermal Resistance (Junction to Case) Test Conditions Symbol TQFP 119 BGA 165 FBGA Unit Still Air, soldered on a 3 x 4.5 inch2, 2-layer printed circuit board ΘJA 31 45 46 °C/W ΘJC 6 7 3 °C/W Notes: 13. Tested initially and after any design or process changes that may affect these parameters. 14. Input waveform should have a slew rate of < 1 ns. Document #: 38-05240 Rev. *A Page 21 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Switching Characteristics Over the Operating Range[15, 16, 17] -250 Parameter Description Min. Max. -225 Min. Max. -200 Min. Max. -167 Min. Max. Unit tCYC Clock Cycle Time 4.0 4.4 5 6 ns tCH Clock HIGH 1.7 2.0 2.0 2.2 ns tCL Clock LOW 1.7 2.0 2.0 2.2 ns tAS Address Set-up Before CLK Rise 1.2 1.4 1.4 1.5 ns tAH Address Hold After CLK Rise 0.3 0.4 0.4 0.5 ns tCO Data Output Valid After CLK Rise tDOH Data Output Hold After CLK Rise 1.0 1.0 1.3 1.3 ns tADS ADSP, ADSC Set-up Before CLK Rise 1.2 1.4 1.4 1.5 ns tADH ADSP, ADSC Hold After CLK Rise 0.3 0.4 0.4 0.5 ns tWES BWE, GW, BWx Set-up Before CLK Rise 1.2 1.4 1.4 1.5 ns tWEH BWE, GW, BWx Hold After CLK Rise 0.3 0.4 0.4 0.5 ns tADVS ADV Set-up Before CLK Rise 1.2 1.4 1.4 1.5 ns tADVH ADV Hold After CLK Rise 0.3 0.4 0.4 0.5 ns tDS Data Input Set-up Before CLK Rise 1.2 1.4 1.4 1.5 ns tDH Data Input Hold After CLK Rise 0.3 0.4 0.4 0.5 ns tCES Chip Enable Set-up 1.2 1.4 1.4 1.5 ns tCEH Chip Enable Hold After CLK Rise 0.3 0.4 0.4 0.5 ns tCHZ tCLZ Clock to High-Z[16] Clock to Low-Z[16] 1.0 High-Z[16, 17] OE HIGH to Output tEOLZ OE LOW to Output Low-Z[16, 17] OE LOW to Output 2.8 2.6 tEOHZ tEOV 2.6 Valid[16] 2.8 1.0 2.6 0 2.8 3.4 1.3 3.0 0 2.8 3.4 3.0 1.3 0 2.6 3.0 ns ns 3.4 0 3.0 ns ns ns 3.4 ns Shaded areas contain preliminary information. Notes: 15. Unless otherwise noted, test conditions assume signal transition time of 1 ns or less, timing reference levels of 1.25V, input pulse levels of 0 to 2.5V, and output loading of the specified IOL/IOH and load capacitance. Shown in (a), (b) and (c) of AC Test Loads. 16. tCHZ, tCLZ, tOEV, tEOLZ, and tEOHZ are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ± 200 mV from steadystate voltage. 17. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ. Document #: 38-05240 Rev. *A Page 22 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY 1 Switching Waveforms Write Cycle Timing[4, 18, 19, 20] Single Write Burst Write Pipelined Write tCH Unselected tCYC CLK tADH tADS tCL ADSP ignored with CE1 inactive ADSP tADH tADS ADSC initiated write ADSC tADVH tADVS ADV tAS ADD ADV Must Be Inactive for ADSP Write WD1 WD3 WD2 tAH GW tWS tWH WE tCES tWH tWS tCEH CE1 masks ADSP CE1 tCES tCEH Unselected with CE2 CE2 CE3 tCES tCEH OE tDH tDS Data High-Z In 1a 1a 2a = UNDEFINED 2b 2c 2d 3a High-Z = DON’T CARE Notes: 18. WE is the combination of BWE and BWx to define a write cycle (see Write Cycle Descriptions table). 19. WDx stands for Write Data to Address X. 20. Device originally deselected. Document #: 38-05240 Rev. *A Page 23 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Switching Waveforms (continued) Read Cycle Timing[4, 18, 20, 21] Single Read tCYC Burst Read Unselected tCH Pipelined Read CLK tADH tADS tCL ADSP ignored with CE1 inactive ADSP tADS ADSC initiated read ADSC tADVS tADH Suspend Burst ADV tADVH tAS ADD RD1 RD3 RD2 tAH GW tWS tWS tWH WE tCES tCEH tWH CE1 masks ADSP CE1 Unselected with CE2 CE2 tCES tCEH CE3 tCES OE tCEH tEOV tOEHZ tDOH Data Out tCO 1a 1a 2a 2b 2c 2c 2d 3a tCLZ = DON’T CARE tCHZ = UNDEFINED Note: 21. RDx stands for Read Data from Address X. Document #: 38-05240 Rev. *A Page 24 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Switching Waveforms (continued) Read/Write Cycle Timing[4, 18, 19, 20, 21] Single Read tCYC Single Write Single Write Single cycle deselect Burst Read tCH Pipelined Read CLK tADS tADH tCL ADSP ADSC tADVS ADV tAS ADD tADVH RD1 WD2 WD3 RD4 RD5 tAH GW tWS tWS tWH WE tCES tWH tCEH CE1 Unselected CE1 CE2 tCES tCEH CE3 tCES tCEH tEOV OE Data In/Out tEOHZ tEOLZ tCO 1a 1a Out 2a In tDS = DON’T CARE Document #: 38-05240 Rev. *A 4a Out 3a In = UNDEFINED tDH tDOH 4b Out 4c Out 4d Out tCHZ I/O Disabled within one clock cycle after deselect Page 25 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Switching Waveforms (continued) Pipelined Read/Write Timing[4, 18, 19, 20, 21] Selected ADSP read ADSC read Unselected ADSC write ADSP write CLK ADSP ADSC ADV ADD RD1 RD2 RD3 RD4 WD5 WD6 5a In 6a In WD8 WD7 GW WE CE1 CE2 CE3 OE Data In/Out 1a 1a Out 2a Out 3a Out = DON’T CARE Document #: 38-05240 Rev. *A 4a Out 7a In = UNDEFINED Page 26 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Switching Waveforms (continued) OE Switching Waveforms OE tEOV tEOHZ I/Os Three-State tEOLZ Document #: 38-05240 Rev. *A Page 27 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Switching Waveforms (continued) ZZ Mode Timing [4, 22, 23] CLK ADSP HIGH ADSC CE1 CE2 LOW HIGH CE3 ZZ IDD tZZS IDD(active) IDDZZ tZZREC I/Os Three-state Notes: 22. Device must be deselected when entering ZZ mode. See Cycle Descriptions Table for all possible signal conditions to deselect the device. 23. I/Os are in three-state when exiting ZZ sleep mode. Document #: 38-05240 Rev. *A Page 28 of 33 CY7C1380CV25 CY7C1382CV25 PRELIMINARY Ordering Information Speed (MHz) 250 225 200 167 225 200 167 Ordering Code CY7C1382CV25-250AC CY7C1380CV25-250AC Package Name A101 Package Type Operating Range 100-Lead Thin Quad Flat Pack Commercial CY7C1382CV25-250BGC CY7C1380CV25-250BGC BG119 119 PBGA CY7C1382CV25-250BZC CY7C1380CV25-250BZC BB165A 165 FBGA CY7C1382CV25-225AC CY7C1380CV25-225AC A101 100-Lead Thin Quad Flat Pack CY7C1382CV25-225BGC CY7C1380CV25-225BGC BG119 119 PBGA CY7C1382CV25-225BZC CY7C1380CV25-225BZC BB165A 165 FBGA CY7C1382CV25-200AC CY7C1380CV25-200AC A101 100-Lead Thin Quad Flat Pack CY7C1382CV25-200BGC CY7C1380CV25-200BGC BG119 119 PBGA CY7C1382CV25-200BZC CY7C1380CV25-200BZC BB165A 165 FBGA CY7C1382CV25-167AC CY7C1380CV25-167AC A101 100-Lead Thin Quad Flat Pack CY7C1382CV25-167BGC CY7C1380CV25-167BGC BG119 119 PBGA CY7C1382CV25-167BZC CY7C1380CV25-167BZC BB165A 165 FBGA CY7C1382CV25-225AI CY7C1380CV25-225AI A101 100-Lead Thin Quad Flat Pack CY7C1382CV25-225BGI CY7C1380CV25-225BGI BG119 119 PBGA CY7C1382CV25-225BZI CY7C1380CV25-225BZC BB165A 165 FBGA CY7C1382CV25-200AI CY7C1380CV25-200AI A101 Industrial 100-Lead Thin Quad Flat Pack CY7C1382CV25-200BGI CY7C1380CV25-200BGI BG119 119 PBGA CY7C1382CV25-200BZI CY7C1380CV25-200BZI BB165A 165 FBGA CY7C1382CV25-167AI CY7C1380CV25-167AI A101 100-Lead Thin Quad Flat Pack CY7C1382CV25-167BGI CY7C1380CV25-167BGI BG119 119 PBGA CY7C1382CV25-167BZI CY7C1380CV25-167BZI BB165A 165 FBGA Shaded areas contain advance information and parts that may not be offered. Document #: 38-05240 Rev. *A Page 29 of 33 PRELIMINARY CY7C1380CV25 CY7C1382CV25 Package Diagrams 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101 51-85050-A Document #: 38-05240 Rev. *A Page 30 of 33 PRELIMINARY CY7C1380CV25 CY7C1382CV25 Package Diagrams (continued) 165-Ball FBGA (13 x 15 x 1.2 mm) BB165A 51-85122-*C Document #: 38-05240 Rev. *A Page 31 of 33 PRELIMINARY CY7C1380CV25 CY7C1382CV25 Package Diagrams (continued) 119-Lead PBGA (14 x 22 x 2.4 mm) BG119 51-85115-*B Intel and Pentium are registered trademarks of Intel Corporation. All product and company names mentioned in this document may be trademarks of their respective holders. Document #: 38-05240 Rev. *A Page 32 of 33 © Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C1380CV25 CY7C1382CV25 PRELIMINARY Document History Page Document Title: CY7C1380CV25/CY7C1382CV25 512K x 36/1M x 18 Pipelined SRAM Document Number: 38-05240 Rev. ECN No. Issue Date Orig. of Change ** 116280 08/29/02 SKX New Data Sheet *A 121543 11/21/02 DSG Updated package diagrams 51-85115 (BG119) to rev. *B and 51-85122 (BB165A) to rev. *C Document #: 38-05240 Rev. *A Description of Change Page 33 of 33