25/0251 CY7C09089/99 CY7C09189/99 64K/128K x 8/9 Synchronous Dual-Port Static RAM Features • True dual-ported memory cells which allow simultaneous access of the same memory location • Six Flow-Through/Pipelined devices — 64K x 8/9 organizations (CY7C09089/189) — 128K x 8/9 organizations (CY7C09099/199) • Three Modes — Flow-Through • Low operating power — Active = 195 mA (typical) — Standby = 0.05 mA (typical) • Fully synchronous interface for easier operation • Burst counters increment addresses internally — Shorten cycle times — Minimize bus noise — Pipelined — Burst • Pipelined output mode on both ports allows fast 100MHz cycle time • 0.35-micron CMOS for optimum speed/power • High-speed clock to data access 6.5[1]/7.5/9/12 ns (max.) • • • • • — Supported in Flow-Through and Pipelined modes Dual Chip Enables for easy depth expansion Automatic power-down Commercial and Industrial temperature ranges Available in 100-pin TQFP Pin-compatible and functionally equivalent to IDT70908 and IDT709089 Logic Block Diagram R/WL R/WR OEL OER CE0L CE1L 1 1 0 0 0/1 0/1 FT/PipeL [2] 1 CE0R CE1R 0/1 0 0 1 0/1 8/9 FT/PipeR [2] 8/9 I/O0L–I/O7/8L I/O0R–I/O7/8R I/O Control [3] A0–A15/16L CLKL ADSL CNTENL CNTRSTL I/O Control 16/17 16/17 Counter/ Address Register Decode True Dual-Ported RAM Array Counter/ Address Register Decode [3] A0–A15/16R CLKR ADSR CNTENR CNTRSTR Notes: 1. See page 7 for Load Conditions. 2. I/O0–I/O7 for x8 devices; I/O0–I/O8 for x9 devices. 3. A0–A15 for 64K; and A0–A16 for 128K devices. For the most recent information, visit the Cypress web site at www.cypress.com Cypress Semiconductor Corporation • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Document #: 38-06039 Rev. *A Revised December 27, 2002 CY7C09089/99 CY7C09189/99 Functional Description The CY7C09089/99 and CY7C09189/99 are high-speed synchronous CMOS 64K and 128K x 8/9 dual-port static RAMs. Two ports are provided, permitting independent, simultaneous access for reads and writes to any location in memory.[4] Registers on control, address, and data lines allow for minimal setup and hold times. In pipelined output mode, data is registered for decreased cycle time. Clock to data valid tCD2 = 6.5 ns[1] (pipelined). Flow-through mode can also be used to bypass the pipelined output register to eliminate access latency. In flow-through mode data will be available tCD1 = 15 ns after the address is clocked into the device. Pipelined output or flowthrough mode is selected via the FT/Pipe pin. Each port contains a burst counter on the input address register. The internal write pulse width is independent of the LOWto-HIGH transition of the clock signal. The internal write pulse is self-timed to allow the shortest possible cycle times. A HIGH on CE0 or LOW on CE1 for one clock cycle will power down the internal circuitry to reduce the static power consumption. The use of multiple Chip Enables allows easier banking of multiple chips for depth expansion configurations. In the pipelined mode, one cycle is required with CE0 LOW and CE1 HIGH to reactivate the outputs. Counter enable inputs are provided to stall the operation of the address input and utilize the internal address generated by the internal counter for fast interleaved memory applications. A port’s burst counter is loaded with the port’s Address Strobe (ADS). When the port’s Count Enable (CNTEN) is asserted, the address counter will increment on each LOW-to-HIGH transition of that port’s clock signal. This will read/write one word from/into each successive address location until CNTEN is deasserted. The counter can address the entire memory array and will loop back to the start. Counter Reset (CNTRST) is used to reset the burst counter. All parts are available in 100-pin Thin Quad Plastic Flatpack (TQFP) packages. Note: 4. When writing simultaneously to the same location, the final value cannot be guaranteed. Document #: 38-06039 Rev. *A Page 2 of 19 CY7C09089/99 CY7C09189/99 Pin Configurations NC NC A6R A5R A4R A3R A2R A1R A0R CNTENR CLKR ADSR GND ADSL CLKL CNTENL A0L A1L A2L A3L A4L A5L A6L NC NC 100-Pin TQFP (Top View) 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 NC 1 75 NC NC 2 74 NC A7L 3 73 A7R A8L 4 72 A8R A9L 5 71 A9R A10L 6 70 A10R A11L 7 69 A11R A12L 8 68 A12R A13L 9 67 A13R A14L 10 66 A14R A15L [5] A16L 11 65 A15R 64 A16R VCC 13 63 GND NC 14 62 NC NC 15 61 NC NC 16 60 NC NC 17 59 NC CE0L 18 58 CE0R CE1L 19 57 CE1R CNTRSTL 20 56 CNTRSTR R/WL 21 55 R/WR OEL [6] FT/PIPEL 22 54 OER 23 53 FT/PIPER NC 24 52 GND NC 25 51 NC CY7C09099 (128K x 8) CY7C09089 (64K x 8) 12 [5] [6] NC NC NC I/O7R I/O6R I/O5R I/O4R I/O3R VCC I/O2R I/01R I/O0R GND VCC I/O0L I/O1L GND I/O2L I/O3L I/O4L I/O5L I/O6L I/O7L NC GND 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Notes: 5. This pin is NC for CY7C09089. 6. For CY7C09089, pin #23 connected to VCC is equivalent to an IDT x8 pipelined device; connecting pin #23 and #53 to GND is equivalent to an IDT x8 flowthrough device. Document #: 38-06039 Rev. *A Page 3 of 19 CY7C09089/99 CY7C09189/99 Pin Configurations (continued) NC A6R A5R A4R A3R A2R A1R A0R CNTENR CLKR ADSR GND GND ADSL CLKL CNTENL A0L A1L A2L A3L A4L A5L A6L NC NC 100-Pin TQFP (Top View) 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 NC 1 75 NC NC 2 74 NC A7L 3 73 A7R A8L 4 72 A8R A9L 5 71 A9R A10L 6 70 A10R A11L 7 69 A11R A12L 8 68 A12R A13L 9 67 A13R A14L 10 66 A14R A15L [7] A16L 11 VCC 13 NC 14 62 NC NC 15 61 NC NC 16 60 NC NC 17 59 NC CE0L 18 58 CE0R CE1L 19 57 CE1R CNTRSTL 20 56 CNTRSTR R/WL 21 55 R/WR CY7C09199 (128K x 9) CY7C09189 (64K x 9) 12 65 A15R 64 A16R 63 GND [7] OEL 22 54 OER FT/PIPEL 23 53 FT/PIPER NC 24 52 GND NC 25 51 NC NC NC I/O8R I/O7R I/O6R I/O5R I/O4R I/O3R VCC I/O2R I/01R I/O0R GND VCC I/O0L I/O1L GND I/O2L I/O3L I/O4L I/O5L I/O6L I/O7L GND I/O8L 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Selection Guide CY7C09089/99 CY7C09189/99 -6[1] CY7C09089/99 CY7C09189/99 -7 CY7C09089/99 CY7C09189/99 -9 CY7C09089/99 CY7C09189/99 -12 fMAX2 (MHz) (Pipelined) 100 83 67 50 Max Access Time (ns) (Clock to Data, Pipelined) 6.5 7.5 9 12 Typical Operating Current ICC (mA) 250 235 215 195 Typical Standby Current for ISB1 (mA) (Both ports TTL Level) 45 40 35 30 Typical Standby Current for ISB3 (mA) (Both ports CMOS Level) 0.05 0.05 0.05 0.05 Note: 7. This pin is NC for CY7C09189. Document #: 38-06039 Rev. *A Page 4 of 19 CY7C09089/99 CY7C09189/99 Pin Definitions Left Port Right Port Description A0L–A16L A0R–A16R Address Inputs (A0−A15 for 64K; and A0−A16 for 128K devices). ADSL ADSR Address Strobe Input. Used as an address qualifier. This signal should be asserted LOW to access the part using an externally supplied address. Asserting this signal LOW also loads the burst counter with the address present on the address pins. CE0L,CE1L CE0R,CE1R Chip Enable Input. To select either the left or right port, both CE0 AND CE1 must be asserted to their active states (CE0 ≤ VIL and CE1 ≥ VIH). CLKL CLKR Clock Signal. This input can be free running or strobed. Maximum clock input rate is fMAX. CNTENL CNTENR Counter Enable Input. Asserting this signal LOW increments the burst address counter of its respective port on each rising edge of CLK. CNTEN is disabled if ADS or CNTRST are asserted LOW. CNTRSTL CNTRSTR Counter Reset Input. Asserting this signal LOW resets the burst address counter of its respective port to zero. CNTRST is not disabled by asserting ADS or CNTEN. I/O0L–I/O8L I/O0R–I/O8R Data Bus Input/Output (I/O0–I/O7 for x8 devices; I/O0–I/O8 for x9 devices). OEL OER Output Enable Input. This signal must be asserted LOW to enable the I/O data pins during read operations. R/WL R/WR Read/Write Enable Input. This signal is asserted LOW to write to the dual port memory array. For read operations, assert this pin HIGH. FT/PIPEL FT/PIPER Flow-Through/Pipelined Select Input. For flow-through mode operation, assert this pin LOW. For pipelined mode operation, assert this pin HIGH. GND Ground Input. NC No Connect. VCC Power Input. Maximum Ratings [8] (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Ambient Temperature with Power Applied .. –55°C to +125°C Output Current into Outputs (LOW)............................. 20 mA Static Discharge Voltage ........................................... >2001V Latch-Up Current...................................................... >200mA Operating Range Supply Voltage to Ground Potential ............... –0.3V to +7.0V Range Ambient Temperature DC Voltage Applied to Outputs in High Z State ................................. –0.5V to +7.0V VCC Commercial 0°C to +70°C 5V ± 10% Industrial[9] −40°C to +85°C 5V ± 10% DC Input Voltage............................................ –0.5V to +7.0V Note: 8. The Voltage on any input or I/O pin cannot exceed the power pin during power-up. 9. Industrial parts are available in CY7C09099 and CY7C09199 only. Document #: 38-06039 Rev. *A Page 5 of 19 CY7C09089/99 CY7C09189/99 Electrical Characteristics Over the Operating Range CY7C09089/99 CY7C09189/99 -6[1] Parameter Description Output HIGH Voltage (VCC = Min., IOH = –4.0 mA) VOL Output LOW Voltage (VCC = Min., IOH = +4.0 mA) VIH Input HIGH Voltage VIL Input LOW Voltage IOZ Output Leakage Current ICC Operating Current (VCC = Max., IOUT = 0 mA) Outputs Disabled ISB2 ISB3 ISB4 -9 -12 Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit VOH ISB1 -7 2.4 2.4 2.4 0.4 2.2 0.4 2.2 Com’l. 10 250 450 10 235 420 Ind.[9] Standby Current (Both Com’l. Ports TTL Level)[10] Ind.[9] CEL & CER ≥ VIH, f = fMAX 45 Standby Current (One Port TTL Level)[10] CEL | CER ≥ VIH, f = fMAX 175 Com’l. Ind. 115 235 40 160 105 220 [9] Standby Current (Both Com’l. Ports CMOS Level)[10] Ind.[9] CEL & CER ≥ VCC – 0.2V, f = 0 0.05 Standby Current (One Port CMOS Level)[10] CEL | CER ≥ VIH, f = fMAX 160 Com’l. 0.5 200 0.05 145 0.5 185 Ind.[9] 0.4 2.2 0.8 −10 V 0.4 2.2 0.8 −10 2.4 V 0.8 −10 10 210 350 245 410 35 95 50 110 140 205 160 220 .05 0.5 0.05 0.5 130 170 145 185 V −10 195 0.8 V 10 µA 305 mA mA 30 85 mA mA 125 190 mA mA 0.05 0.5 mA mA 110 150 mA mA Capacitance Parameter Description CIN Input Capacitance COUT Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC = 5.0V Max. Unit 10 pF 10 pF Note: 10. CEL and CER are internal signals. To select either the left or right port, both CE0 AND CE1 must be asserted to their active states (CE0 ≤ VIL and CE1 ≥ VIH). Document #: 38-06039 Rev. *A Page 6 of 19 CY7C09089/99 CY7C09189/99 AC Test Loads 5V 5V R1 = 893Ω OUTPUT C = 30 pF RTH = 250Ω OUTPUT R1 = 893Ω OUTPUT C = 30 pF R2 = 347Ω C = 5 pF R2 = 347Ω VTH = 1.4V (a) Normal Load (Load 1) (c) Three-State Delay (Load 2) (Used for tCKLZ, tOLZ, & tOHZ including scope and jig) (b) Thévenin Equivalent (Load 1) AC Test Loads (Applicable to -6 only)[11] OUTPUT Z0 = 50Ω R = 50Ω ALL INPUT PULSES 3.0V C GND VTH = 1.4V 10% 90% 10% 90% ≤ 3 ns ≤ 3 ns (a) Load 1 (-6 only) 0. 60 ∆ (ns) for all -6 access times 0. 50 0. 40 0. 30 0. 20 0. 1 0 0. 00 10 15 20 25 30 35 Capacitance (pF) (b) Load Derating Curve Note: 11. Test Conditions: C = 10 pF. Document #: 38-06039 Rev. *A Page 7 of 19 CY7C09089/99 CY7C09189/99 Switching Characteristics Over the Operating Range CY7C09089/99 CY7C09189/99 -6[1] Parameter Description -7 -9 -12 Max. Unit fMAX1 fMax Flow-Through 53 45 40 33 MHz fMAX2 fMax Pipelined 100 83 67 50 MHz tCYC1 Clock Cycle Time - Flow-Through tCYC2 Clock Cycle Time - Pipelined tCH1 Clock HIGH Time - Flow-Through tCL1 Clock LOW Time - Flow-Through tCH2 Min. Max. Max. Min. Max. Min. 22 25 30 ns 10 12 15 20 ns 6.5 7.5 12 12 ns 6.5 7.5 12 12 ns Clock HIGH Time - Pipelined 4 5 6 8 ns tCL2 Clock LOW Time - Pipelined 4 tR Clock Rise Time 3 3 3 3 ns tF Clock Fall Time 3 3 3 3 ns tSA Address Set-Up Time tHA Address Hold Time tSC Chip Enable Set-Up Time tHC Chip Enable Hold Time tSW R/W Set-Up Time tHW R/W Hold Time tSD Input Data Set-Up Time tHD Input Data Hold Time tSAD ADS Set-Up Time tHAD ADS Hold Time tSCN CNTEN Set-Up Time tHCN CNTEN Hold Time tSRST CNTRST Set-Up Time tHRST CNTRST Hold Time tOE Output Enable to Data Valid tOLZ 19 Min. 6 8 ns 3.5 4 4 4 ns 0 0 1 1 ns 3.5 4 4 4 ns 0 0 1 1 ns 3.5 4 4 4 ns 0 0 1 1 ns 3.5 4 4 4 ns 0 0 1 1 ns 3.5 4 4 4 ns 0 0 1 1 ns 3.5 4 4 4 ns 0 0 1 1 ns 3.5 4 4 4 ns 0 0 8 [12, 13] OE to Low Z 2 [12, 13] OE to High Z 1 tOHZ 5 1 9 2 7 1 1 10 2 7 1 ns 12 2 7 1 ns ns 7 ns tCD1 Clock to Data Valid - Flow-Through 15 18 20 25 ns tCD2 Clock to Data Valid - Pipelined 6.5 7.5 9 12 ns Data Output Hold After Clock HIGH 2 [12, 13] Clock HIGH to Output High Z 2 [12, 13] Clock HIGH to Output Low Z 2 tDC tCKHZ tCKLZ 2 9 2 2 9 2 2 2 9 2 2 ns 9 2 ns ns Port to Port Delays tCWDD Write Port Clock HIGH to Read Data Delay 30 35 40 40 ns tCCS Clock to Clock Set-Up Time 9 10 15 15 ns Notes: 12. Test conditions used are Load 2. 13. This parameter is guaranteed by design, but is not production tested. Document #: 38-06039 Rev. *A Page 8 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms Read Cycle for Flow-Through Output (FT/PIPE = VIL)[14, 15, 16, 17] tCH1 tCYC1 tCL1 CLK CE0 tSC tHC tSW tSA tHW tHA tSC tHC CE1 R/W An ADDRESS An+1 An+2 An+3 tCKHZ tDC tCD1 DATAOUT Qn Qn+1 Qn+2 tDC tCKLZ tOHZ tOLZ OE tOE Read Cycle for Pipelined Operation (FT/PIPE = VIH)[14, 15, 16, 17] tCH2 tCYC2 tCL2 CLK CE0 tSC tHC tSW tSA tHW tHA tSC tHC CE1 R/W ADDRESS An DATAOUT An+1 1 Latency An+2 tDC tCD2 Qn tCKLZ An+3 Qn+1 tOHZ Qn+2 tOLZ OE tOE Notes: 14. OE is asynchronously controlled; all other inputs are synchronous to the rising clock edge. 15. ADS = VIL, CNTEN and CNTRST = VIH. 16. The output is disabled (high-impedance state) by CE0=VIH or CE1 = VIL following the next rising edge of the clock. 17. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK. Numbers are for reference only. Document #: 38-06039 Rev. *A Page 9 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Bank Select Pipelined Read[18, 19] tCH2 tCYC2 tCL2 CLKL tHA tSA ADDRESS(B1) A0 A1 A3 A2 A4 A5 tHC tSC CE0(B1) tCD2 tHC tSC tCD2 tHA tSA ADDRESS(B2) tDC A0 A1 tDC tSC tCKLZ A3 A2 tCKHZ D3 D1 D0 DATAOUT(B1) tCD2 tCKHZ A4 A5 tHC CE0(B2) tSC tCD2 tHC DATAOUT(B2) tCKHZ tCD2 D4 D2 tCKLZ tCKLZ Left Port Write to Flow-Through Right Port Read[20, 21, 22, 23] CLKL tSW tHW tSA tHA R/WL ADDRESSL NO MATCH MATCH tHD tSD DATAINL VALID tCCS CLKR R/WR tCD1 tSW tSA ADDRESSR tHW tHA NO MATCH MATCH tCWDD DATAOUTR tCD1 VALID tDC VALID tDC Notes: 18. In this depth expansion example, B1 represents Bank #1 and B2 is Bank #2; Each Bank consists of one Cypress dual-port device from this data sheet. ADDRESS(B1) = ADDRESS(B2). 19. OE and ADS = VIL; CE1(B1), CE1(B2), R/W, CNTEN, and CNTRST = VIH. 20. The same waveforms apply for a right port write to flow-through left port read. 21. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 22. OE = VIL for the right port, which is being read from. OE = VIH for the left port, which is being written to. 23. It tCCS ≤ maximum specified, then data from right port READ is not valid until the maximum specified for tCWDD. If tCCS>maximum specified, then data is not valid until tCCS + tCD1. tCWDD does not apply in this case. Document #: 38-06039 Rev. *A Page 10 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Pipelined Read-to-Write-to-Read (OE = VIL)[17, 24, 25, 26] tCH2 tCYC2 tCL2 CLK CE0 tSC tHC CE1 tSW tHW R/W tSW tHW An ADDRESS An+1 tSA An+2 An+2 An+3 An+4 tSD tHD tHA DATAIN tCD2 tCKHZ Dn+2 tCD2 tCKLZ Qn DATAOUT READ Qn+3 NO OPERATION WRITE READ Pipelined Read-to-Write-to-Read (OE Controlled)[17, 24, 25, 26] tCH2 tCYC2 tCL2 CLK CE0 tSC tHC CE1 R/W tSW tHW tSW tHW An An+1 An+2 An+3 An+4 An+5 ADDRESS tSA tHA tSD tHD Dn+2 DATAIN Dn+3 tCD2 DATAOUT tCKLZ tCD2 Qn Qn+4 tOHZ OE READ WRITE READ Notes: 24. Output state (HIGH, LOW, or High-Impedance) is determined by the previous cycle control signals. 25. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 26. During “No Operation,” data in memory at the selected address may be corrupted and should be rewritten to ensure data integrity. Document #: 38-06039 Rev. *A Page 11 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Flow-Through Read-to-Write-to-Read (OE = VIL)[15, 18, 24, 25] tCH1 tCYC1 tCL1 CLK CE0 tSC tHC CE1 tSW tHW R/W tSW tHW An ADDRESS An+1 tSA DATAIN An+2 An+2 tSD tHA An+3 tHD Dn+2 tCD1 tCD1 DATAOUT An+4 tCD1 Qn Qn+1 tDC tCKHZ READ tCD1 Qn+3 tCKLZ NO OPERATION WRITE tDC READ Flow-Through Read-to-Write-to-Read (OE Controlled)[15, 18, 24, 25] tCH1 tCYC1 tCL1 CLK CE0 tSC tHC CE1 tSW tHW R/W tSW tHW An An+1 An+2 An+3 An+4 An+5 ADDRESS tSA DATAIN tSD tHA DATAOUT Dn+2 tDC tCD1 tHD Dn+3 tOE tCD1 Qn tCD1 Qn+4 tOHZ tCKLZ tDC OE READ Document #: 38-06039 Rev. *A WRITE READ Page 12 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Pipelined Read with Address Counter Advance[27] tCH2 tCYC2 tCL2 CLK tSA tHA ADDRESS An tSAD tHAD ADS tSAD tHAD tSCN tHCN CNTEN tSCN DATAOUT tHCN Qx-1 tCD2 Qx READ EXTERNAL ADDRESS Qn Qn+1 tDC READ WITH COUNTER Qn+2 COUNTER HOLD Qn+3 READ WITH COUNTER Flow-Through Read with Address Counter Advance[27] tCH1 tCYC1 tCL1 CLK tSA tHA An ADDRESS tSAD tHAD ADS tSAD tHAD tSCN tHCN CNTEN tSCN DATAOUT tHCN tCD1 Qx Qn Qn+1 tDC READ EXTERNAL ADDRESS READ WITH COUNTER Qn+3 Qn+2 COUNTER HOLD READ WITH COUNTER Note: 27. CE0 and OE = VIL; CE1, R/W and CNTRST = VIH. Document #: 38-06039 Rev. *A Page 13 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Write with Address Counter Advance (Flow-Through or Pipelined Outputs)[28, 29] tCH2 tCYC2 tCL2 CLK tSA tHA An ADDRESS INTERNAL ADDRESS An tSAD tHAD tSCN tHCN An+1 An+2 An+3 An+4 ADS CNTEN Dn DATAIN tSD tHD WRITE EXTERNAL ADDRESS Dn+1 Dn+1 WRITE WITH COUNTER Dn+2 WRITE COUNTER HOLD Dn+3 Dn+4 WRITE WITH COUNTER Notes: 28. CE0 and R/W = VIL; CE1 and CNTRST = VIH. 29. The “Internal Address” is equal to the “External Address” when ADS = VIL and equals the counter output when ADS = VIH. Document #: 38-06039 Rev. *A Page 14 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Counter Reset (Pipelined Outputs)[17, 24, 30, 31] tCH2 tCYC2 tCL2 CLK tSA tHA An ADDRESS INTERNAL ADDRESS AX 0 tSW tHW tSD tHD 1 An+1 An An+1 R/W tSAD tHAD tSCN tHCN tSRST tHRST ADS CNTEN CNTRST DATAIN D0 DATAOUT Q0 COUNTER RESET WRITE ADDRESS 0 READ ADDRESS 0 READ ADDRESS 1 Q1 Qn READ ADDRESS n Notes: 30. CE0 = VIL; CE1 = VIH. 31. No dead cycle exists during counter reset. A READ or WRITE cycle may be coincidental with the counter reset. Document #: 38-06039 Rev. *A Page 15 of 19 CY7C09089/99 CY7C09189/99 Read/Write and Enable Operation[32, 33, 34] Inputs OE CLK Outputs CE0 CE1 R/W I/O0–I/O8 X H X X High-Z Deselected[35] X X L X High-Z Deselected[35] X L H L DIN L L H H DOUT Read[33] L H X High-Z Outputs Disabled H X Operation Write Address Counter Control Operation[32, 36, 37, 38] Address Previous Address ADS CNTEN CNTRST I/O Mode X X X X L Dout(0) Reset Counter Reset to Address 0 An X L X H Dout(n) Load Address Load into Counter X An H H H Dout(n) Hold External Address Blocked—Counter Disabled X An H L H Dout(n+1) Increment Counter Enabled—Internal Address Generation CLK Operation Notes: 32. “X” = “Don’t Care,” “H” = VIH, “L” = VIL. 33. ADS, CNTEN, CNTRST = “Don’t Care.” 34. OE is an asynchronous input signal. 35. When CE changes state in the pipelined mode, deselection and read happen in the following clock cycle. 36. CE0 and OE = VIL; CE1 and R/W = VIH. 37. Data shown for flow-through mode; pipelined mode output will be delayed by one cycle. 38. Counter operation is independent of CE0 and CE1. Document #: 38-06039 Rev. *A Page 16 of 19 CY7C09089/99 CY7C09189/99 Ordering Information 64K x8 Synchronous Dual-Port SRAM Speed (ns) Ordering Code Package Name Package Type Operating Range 6.5[1] CY7C09089-6AC A100 100-Pin Thin Quad Flat Pack Commercial 7.5 CY7C09089-7AC A100 100-Pin Thin Quad Flat Pack Commercial 9 CY7C09089-9AC A100 100-Pin Thin Quad Flat Pack Commercial 12 CY7C09089-12AC A100 100-Pin Thin Quad Flat Pack Commercial 128K x8 Synchronous Dual-Port SRAM Speed (ns) Ordering Code Package Name Package Type Operating Range 6.5 CY7C09099-6AC A100 100-Pin Thin Quad Flat Pack Commercial 7.5 CY7C09099-7AC A100 100-Pin Thin Quad Flat Pack Commercial 9 CY7C09099-9AC A100 100-Pin Thin Quad Flat Pack Commercial CY7C09099-9AI A100 100-Pin Thin Quad Flat Pack Industrial CY7C09099-12AC A100 100-Pin Thin Quad Flat Pack Commercial 12 64K x9 Synchronous Dual-Port SRAM Speed (ns) Ordering Code Package Name Package Type Operating Range 6.5 CY7C09189-6AC A100 100-Pin Thin Quad Flat Pack Commercial 7.5 CY7C09189-7AC A100 100-Pin Thin Quad Flat Pack Commercial 9 CY7C09189-9AC A100 100-Pin Thin Quad Flat Pack Commercial 12 CY7C09189-12AC A100 100-Pin Thin Quad Flat Pack Commercial 128K x9 Synchronous Dual-Port SRAM Speed (ns) 6.5 Ordering Code CY7C09199-6AC Package Name A100 Package Type 100-Pin Thin Quad Flat Pack Operating Range Commercial 7.5 CY7C09199-7AC A100 100-Pin Thin Quad Flat Pack Commercial 9 CY7C09199-9AC A100 100-Pin Thin Quad Flat Pack Commercial CY7C09199-9AI A100 100-Pin Thin Quad Flat Pack Industrial 12 CY7C09199-12AC A100 100-Pin Thin Quad Flat Pack Commercial Document #: 38-06039 Rev. *A Page 17 of 19 CY7C09089/99 CY7C09189/99 Package Diagram 100-Pin Thin Plastic Quad Flat Pack (TQFP) A100 51-85048-B Document #: 38-06039 Rev. *A Page 18 of 19 © Cypress Semiconductor Corporation, 2001. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C09089/99 CY7C09189/99 Document Title: CY7C09089/99, CY7C09189/99 64K/128K x 8/9 Synchronous Dual Port Static RAM Document Number: 38-06039 ECN NO. Issue Date Orig. of Change ** 110187 10/21/01 SZV Change from Spec number: 38-00663 to 38-06039 *A 122289 12/27/02 RBI Added power up information to maximum ratings information. REV. Document #: 38-06039 Rev. *A Description of Change Page 19 of 19