CYPRESS CY7C63743C

CY7C63722C
CY7C63723C
CY7C63743C
enCoRe™ USB Combination Low-Speed
USB and PS/2 Peripheral Controller
Features
■
enCoRe™ USB - enhanced Component Reduction
❐ Internal oscillator eliminates the need for an external crystal
or resonator
❐ Interface can auto-configure to operate as PS/2 or USB without the need for external components to switch between
modes (no General Purpose I/O [GPIO] pins needed to manage dual mode capability)
❐ Internal 3.3V regulator for USB pull-up resistor
❐ Configurable GPIO for real-world interface without external
components
■
Flexible, cost-effective solution for applications that combine
PS/2 and low-speed USB, such as mice, gamepads, joysticks,
and many others.
■
USB Specification Compliance
❐ Conforms to USB Specification, Version 2.0
❐ Conforms to USB HID Specification, Version 1.1
❐ Supports one low-speed USB device address and three data
endpoints
❐ Integrated USB transceiver
❐ 3.3V regulated output for USB pull-up resistor
■
■
8-bit RISC microcontroller
❐ Harvard architecture
❐ 6-MHz external ceramic resonator or internal clock mode
❐ 12-MHz internal CPU clock
❐ Internal memory
❐ 256 bytes of RAM
❐ 8 Kbytes of EPROM
❐ Interface can auto-configure to operate as PS/2 or USB
❐ No external components for switching between PS/2 and
USB modes
❐ No GPIO pins needed to manage dual mode capability
■
SPI serial communication block
❐ Master or slave operation
❐ 2 Mbit/s transfers
■
Four 8-bit Input Capture registers
❐ Two registers each for two input pins
❐ Capture timer setting with five prescaler settings
❐ Separate registers for rising and falling edge capture
❐ Simplifies interface to RF inputs for wireless applications
■
Internal low-power wake-up timer during suspend mode
❐ Periodic wake-up with no external components
■
Optional 6-MHz internal oscillator mode
❐ Allows fast start-up from suspend mode
■
Watchdog Reset (WDR)
■
Low-voltage Reset at 3.75V
■
Internal brown-out reset for suspend mode
■
Improved output drivers to reduce EMI
■
Operating voltage from 4.0V to 5.5VDC
■
Operating temperature from 0°C to 70°C
■
CY7C63723C available in 18-pin SOIC, 18-pin PDIP
■
CY7C63743C available in 24-pin SOIC, 24-pin PDIP, 24-pin
QSOP
■
CY7C63722C available in DIE form
■
Industry standard programmer support
I/O ports
❐ Up to 16 versatile GPIO pins, individually configurable
❐ High current drive on any GPIO pin: 50 mA/pin current sink
❐ Each GPIO pin supports high-impedance inputs, internal
pull-ups, open drain outputs or traditional CMOS outputs
❐ Maskable interrupts on all I/O pins
Cypress Semiconductor Corporation
Document #: 38-08022 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 15, 2011
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Logic Block Diagram
XTALIN/P2.1
XTALOUT
Internal
Oscillator
Xtal
Oscillator
EPROM
8K Byte
8-bit
RISC
Core
Brown-out
Reset
Watch
Dog
Timer
Low
Voltage
Reset
Wake-Up
Timer
RAM
256 Byte
12-bit
Timer
Capture
Timers
Interrupt
Controller
USB
Engine
Port 1
GPIO
Port 0
GPIO
3.3V
Regulator
USB &
PS/2
Xcvr
VREG/P2.0
D+,D–
Functional Overview
enCoRe USB—The New USB Standard
Cypress has reinvented its leadership position in the low-speed
USB
market
with
a
new
family
of
innovative
microcontrollers. Introducing...enCoRe USB—“enhanced
Component Reduction.” Cypress has leveraged its design
expertise in USB solutions to create a new family of low-speed
USB microcontrollers that enables peripheral developers to
design new products with a minimum number of components. At
the heart of the enCoRe USB technology is the breakthrough
design of a crystalless oscillator. By integrating the oscillator into
our chip, an external crystal or resonator is no longer needed.
We have also integrated other external components commonly
found in low-speed USB applications such as pull-up resistors,
wake-up circuitry, and a 3.3V regulator. All of this adds up to a
lower system cost.
The CY7C637xxC is an 8-bit RISC one-time-programmable
(OTP) microcontroller. The instruction set has been optimized
specifically for USB and PS/2 operations, although the microcontrollers can be used for a variety of other embedded applications.
The CY7C637xxC features up to 16 GPIO pins to support USB,
PS/2 and other applications. The I/O pins are grouped into two
ports (Port 0 to 1) where each pin can be individually configured
as inputs with internal pull-ups, open drain outputs, or traditional
CMOS outputs with programmable drive strength of up to 50 mA
output drive. Additionally, each I/O pin can be used to generate
a GPIO interrupt to the microcontroller. Note the GPIO interrupts
all share the same “GPIO” interrupt vector.
The CY7C637xxC microcontrollers feature an internal oscillator.
With the presence of USB traffic, the internal oscillator can be set
to precisely tune to USB timing requirements (6 MHz ±1.5%).
Document #: 38-08022 Rev. *E
P1.0–P1.7
SPI
P0.0–P0.7
Optionally, an external 6-MHz ceramic resonator can be used to
provide a higher precision reference for USB operation. This
clock generator reduces the clock-related noise emissions
(EMI). The clock generator provides the 6- and 12-MHz clocks
that remain internal to the microcontroller.
The CY7C637xxC has 8 Kbytes of EPROM and 256 bytes of
data RAM for stack space, user variables, and USB FIFOs.
These parts include low-voltage reset logic, a Watchdog timer, a
vectored interrupt controller, a 12-bit free-running timer, and
capture timers. The low-voltage reset (LVR) logic detects when
power is applied to the device, resets the logic to a known state,
and begins executing instructions at EPROM address 0x0000.
LVR will also reset the part when VCC drops below the operating
voltage range. The Watchdog timer can be used to ensure the
firmware never gets stalled for more than approximately 8 ms.
The microcontroller supports 10 maskable interrupts in the
vectored interrupt controller. Interrupt sources include the USB
Bus-Reset, the 128-s and 1.024-ms outputs from the
free-running timer, three USB endpoints, two capture timers, an
internal wake-up timer and the GPIO ports. The timers bits cause
periodic interrupts when enabled. The USB endpoints interrupt
after USB transactions complete on the bus. The capture timers
interrupt whenever a new timer value is saved due to a selected
GPIO edge event. The GPIO ports have a level of masking to
select which GPIO inputs can cause a GPIO interrupt. For
additional flexibility, the input transition polarity that causes an
interrupt is programmable for each GPIO pin. The interrupt
polarity can be either rising or falling edge.
The free-running 12-bit timer clocked at 1 MHz provides two
interrupt sources as noted above (128 s and 1.024 ms). The
timer can be used to measure the duration of an event under
firmware control by reading the timer at the start and end of an
Page 2 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
event, and subtracting the two values. The four capture timers
save a programmable 8 bit range of the free-running timer when
a GPIO edge occurs on the two capture pins (P0.0, P0.1).
The CY7C637xxC includes an integrated USB serial interface
engine (SIE) that supports the integrated peripherals. The
hardware supports one USB device address with three
endpoints. The SIE allows the USB host to communicate with the
function integrated into the microcontroller. A 3.3V regulated
output pin provides a pull-up source for the external USB resistor
on the D– pin.
The USB D+ and D– USB pins can alternately be used as PS/2
SCLK and SDATA signals, so that products can be designed to
respond to either USB or PS/2 modes of operation. PS/2
operation is supported with internal pull-up resistors on SCLK
and SDATA, the ability to disable the regulator output pin, and an
interrupt to signal the start of PS/2 activity. No external components are necessary for dual USB and PS/2 systems, and no
GPIO pins need to be dedicated to switching between modes.
Slow edge rates operate in both modes to reduce EMI.
Pin Configurations
Top View
P0.0
P0.1
P0.2
P0.3
P1.0
P1.2
P1.4
P1.6
VSS
VPP
VREG/P2.0
XTALIN/P2.1
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
P0.4
P0.5
P0.6
P0.7
P1.1
P1.3
P1.5
P1.7
D+/SCLK
D–/SDATA
VCC
XTALOUT
P0.3
P1.0
P1.2
P1.4
P1.6
VSS
4
5
6
7
8
9
22
21
20
19
18
VSS 10
P0.7
P1.1
P1.3
P1.5
P1.7
17 D+/SCLK
13
14
15
16
P0.4
P0.5
P0.6
P0.7
P1.1
D+/SCLK
D–/SDATA
VCC
XTALOUT
XTALIN/P2.1
XTALOUT
VCC
D-/SDATA
18
17
16
15
14
13
12
11
10
P0.2
P0.1
P0.0
P0.4
P0.5
P0.6
1
2
3
4
5
6
7
8
9
CY7C63722C-XC
DIE
3
2
1
25
24
23
P0.0
P0.1
P0.2
P0.3
P1.0
VSS
VPP
VREG/P2.0
XTALIN/P2.1
CY7C63743C
24-pin SOIC/PDIP/QSOP
VPP 11
VREG 12
CY7C63723C
18-pin SOIC/PDIP
Pin Definitions
Name
I/O
CY7C63723C CY7C63743C CY7C63722C
18-Pin
24-Pin
25-Pad
15
16
16
17
Description
D–/SDATA,
D+/SCLK
I/O
12
13
P0[7:0]
I/O
1, 2, 3, 4,
15, 16, 17, 18
1, 2, 3, 4,
1, 2, 3, 4,
GPIO Port 0 capable of sinking up to 50 mA/pin, or
21, 22, 23, 24 22, 23, 24, 25 sinking controlled low or high programmable current.
Can also source 2 mA current, provide a resistive
pull-up, or serve as a high-impedance input. P0.0 and
P0.1 provide inputs to Capture Timers A and B, respectively.
P1[7:0]
I/O
5, 14
5, 6, 7, 8,
5, 6, 7, 8,
IO Port 1 capable of sinking up to 50 mA/pin, or sinking
17, 18, 19, 20 18, 19, 20, 21 controlled low or high programmable current. Can also
source 2 mA current, provide a resistive pull-up, or
serve as a high-impedance input.
XTALIN/P2.1
IN
9
12
13
6-MHz ceramic resonator or external clock input, or
P2.1 input
OUT
10
13
14
6-MHz ceramic resonator return pin or internal oscillator
output
VPP
7
10
11
Programming voltage supply, ground for normal
operation
XTALOUT
USB differential data lines (D– and D+), or PS/2 clock
and data signals (SDATA and SCLK)
VCC
11
14
15
Voltage supply
VREG/P2.0
8
11
12
Voltage supply for 1.3-k USB pull-up resistor (3.3V
nominal). Also serves as P2.0 input.
VSS
6
9
9, 10
Document #: 38-08022 Rev. *E
Ground
Page 3 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Programming Model
Refer to the CYASM Assembler User’s Guide for more details on
firmware operation with the CY7C637xxC microcontrollers.
Program Counter (PC)
decremented again and the first byte is restored from memory
addressed by the PSP. After the program counter and flags have
been restored from stack, the interrupts are enabled. The effect
is to restore the program counter and flags from the program
stack, decrement the program stack pointer by two, and reenable
interrupts.
The 14-bit program counter (PC) allows access for up to 8
Kbytes of EPROM using the CY7C637xxC architecture. The
program counter is cleared during reset, such that the first
instruction executed after a reset is at address 0x0000. This
instruction is typically a jump instruction to a reset handler that
initializes the application.
The call subroutine (CALL) instruction stores the program
counter and flags on the program stack and increments the PSP
by two.
The lower 8 bits of the program counter are incremented as
instructions are loaded and executed. The upper six bits of the
program counter are incremented by executing an XPAGE
instruction. As a result, the last instruction executed within a
256-byte “page” of sequential code should be an XPAGE
instruction. The assembler directive “XPAGEON” will cause the
assembler to insert XPAGE instructions automatically. As
instructions can be either one or two bytes long, the assembler
may occasionally need to insert a NOP followed by an XPAGE
for correct execution.
Note that there are restrictions in using the JMP, CALL, and
INDEX instructions across the 4-KByte boundary of the program
memory. Refer to the CYASM Assembler User’s Guide for a
detailed description.
The program counter of the next instruction to be executed, carry
flag, and zero flag are saved as two bytes on the program stack
during an interrupt acknowledge or a CALL instruction. The
program counter, carry flag, and zero flag are restored from the
program stack only during a RETI instruction.
Please note the program counter cannot be accessed directly by
the firmware. The program stack can be examined by reading
SRAM from location 0x00 and up.
8-bit Accumulator (A)
The accumulator is the general-purpose, do everything register
in the architecture where results are usually calculated.
8-bit Index Register (X)
The return from subroutine (RET) instruction restores the
program counter, but not the flags, from program stack and
decrements the PSP by two.
8-bit Data Stack Pointer (DSP)
The data stack pointer (DSP) supports PUSH and POP instructions that use the data stack for temporary storage. A PUSH
instruction will pre-decrement the DSP, then write data to the
memory location addressed by the DSP. A POP instruction will
read data from the memory location addressed by the DSP, then
post-increment the DSP.
During a reset, the Data Stack Pointer will be set to zero. A PUSH
instruction when DSP equals zero will write data at the top of the
data RAM (address 0xFF). This would write data to the memory
area reserved for a FIFO for USB endpoint 0. In non-USB applications, this works fine and is not a problem.
For USB applications, the firmware should set the DSP to an
appropriate location to avoid a memory conflict with RAM
dedicated to USB FIFOs. The memory requirements for the USB
endpoints are shown in Section . For example, assembly instructions to set the DSP to 20h (giving 32 bytes for program and data
stack combined) are shown below.
MOV A,20h
; Move 20 hex into Accumulator (must be D8h
or less to avoid USB FIFOs)
The index register “X” is available to the firmware as an auxiliary
accumulator. The X register also allows the processor to perform
indexed operations by loading an index value into X.
SWAP A,DSP ; swap accumulator value into DSP register
8-bit Program Stack Pointer (PSP)
Address Modes
During a reset, the program stack pointer (PSP) is set to zero.
This means the program “stack” starts at RAM address 0x00 and
“grows” upward from there. Note that the program stack pointer
is directly addressable under firmware control, using the MOV
PSP,A instruction. The PSP supports interrupt service under
hardware control and CALL, RET, and RETI instructions under
firmware control.
The CY7C637xxC microcontrollers support three addressing
modes for instructions that require data operands: data, direct,
and indexed.
During an interrupt acknowledge, interrupts are disabled and the
program counter, carry flag, and zero flag are written as two
bytes of data memory. The first byte is stored in the memory
addressed by the program stack pointer, then the PSP is incremented. The second byte is stored in memory addressed by the
program stack pointer and the PSP is incremented again. The
net effect is to store the program counter and flags on the
program “stack” and increment the program stack pointer by two.
The return from interrupt (RETI) instruction decrements the
program stack pointer, then restores the second byte from
memory addressed by the PSP. The program stack pointer is
Document #: 38-08022 Rev. *E
Data
The “Data” address mode refers to a data operand that is actually
a constant encoded in the instruction. As an example, consider
the instruction that loads A with the constant 0x30:
■
MOV A, 30h
This instruction will require two bytes of code where the first byte
identifies the “MOV A” instruction with a data operand as the
second byte. The second byte of the instruction will be the
constant “0xE8h”. A constant may be referred to by name if a
prior “EQU” statement assigns the constant value to the name.
For example, the following code is equivalent to the example
shown above.
■
DSPINIT: EQU 30h
Page 4 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
■
Indexed
MOV A,DSPINIT
Direct
“Direct” address mode is used when the data operand is a
variable stored in SRAM. In that case, the one byte address of
the variable is encoded in the instruction. As an example,
consider an instruction that loads A with the contents of memory
address location 0x10h:
■
MOV A, [10h]
In normal usage, variable names are assigned to variable
addresses using “EQU” statements to improve the readability of
the assembler source code. As an example, the following code
is equivalent to the example shown above.
■
buttons: EQU 10h
■
MOV A, [buttons]
“Indexed” address mode allows the firmware to manipulate
arrays of data stored in SRAM. The address of the data operand
is the sum of a constant encoded in the instruction and the
contents of the “X” register. In normal usage, the constant will be
the “base” address of an array of data and the X register will
contain an index that indicates which element of the array is
actually addressed.
■
array: EQU 10h
■
MOV X,3
■
MOV A, [x+array]
This would have the effect of loading A with the fourth element
of the SRAM “array” that begins at address 0x10h. The fourth
element would be at address 0x13h.
Instruction Set Summary
Refer to the CYASM Assembler User’s Guide for detailed information on these instructions. Note that conditional jump instructions (i.e., JC, JNC, JZ, JNZ) take five cycles if jump is taken, four
cycles if no jump.
MNEMONIC
Operand
HALT
Opcode
Cycles
MNEMONIC
00
7
NOP
Operand
Opcode
Cycles
20
4
ADD A,expr
data
01
4
INC A
acc
21
4
ADD A,[expr]
direct
02
6
INC X
x
22
4
ADD A,[X+expr]
index
03
7
INC [expr]
direct
23
7
ADC A,expr
data
04
4
INC [X+expr]
index
24
8
ADC A,[expr]
direct
05
6
DEC A
acc
25
4
ADC A,[X+expr]
index
06
7
DEC X
x
26
4
SUB A,expr
data
07
4
DEC [expr]
direct
27
7
SUB A,[expr]
direct
08
6
DEC [X+expr]
index
28
8
SUB A,[X+expr]
index
09
7
IORD expr
address
29
5
SBB A,expr
data
0A
4
IOWR expr
address
2A
5
SBB A,[expr]
direct
0B
6
POP A
2B
4
SBB A,[X+expr]
index
0C
7
POP X
2C
4
OR A,expr
data
0D
4
PUSH A
2D
5
OR A,[expr]
direct
0E
6
PUSH X
2E
5
OR A,[X+expr]
index
0F
7
SWAP A,X
2F
5
AND A,expr
data
10
4
SWAP A,DSP
30
5
AND A,[expr]
direct
11
6
MOV [expr],A
direct
31
5
AND A,[X+expr]
index
12
7
MOV [X+expr],A
index
32
6
XOR A,expr
data
13
4
OR [expr],A
direct
33
7
XOR A,[expr]
direct
14
6
OR [X+expr],A
index
34
8
XOR A,[X+expr]
index
15
7
AND [expr],A
direct
35
7
CMP A,expr
data
16
5
AND [X+expr],A
index
36
8
CMP A,[expr]
direct
17
7
XOR [expr],A
direct
37
7
CMP A,[X+expr]
index
18
8
XOR [X+expr],A
index
38
8
MOV A,expr
data
19
4
IOWX [X+expr]
index
39
6
Document #: 38-08022 Rev. *E
Page 5 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
MNEMONIC
Operand
Opcode
Cycles
MNEMONIC
Operand
Opcode
Cycles
MOV A,[expr]
direct
1A
5
CPL
3A
4
MOV A,[X+expr]
index
1B
6
ASL
3B
4
MOV X,expr
data
1C
4
ASR
3C
4
MOV X,[expr]
direct
1D
5
RLC
3D
4
reserved
1E
RRC
3E
4
XPAGE
1F
4
RET
3F
8
MOV A,X
40
4
DI
70
4
MOV X,A
41
4
EI
72
4
MOV PSP,A
60
4
RETI
73
8
addr
C0-CF
5 (or 4)
CALL
addr
50 - 5F
10
JMP
addr
80-8F
5
JC
CALL
addr
90-9F
10
JNC
addr
D0-DF
5 (or 4)
JZ
addr
A0-AF
5 (or 4)
JACC
addr
E0-EF
7
JNZ
addr
B0-BF
5 (or 4)
INDEX
addr
F0-FF
14
Document #: 38-08022 Rev. *E
Page 6 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Memory Organization
Program Memory Organization[1]
After reset
14 -bit PC
Address
0x0000
Program execution begins here after a reset
0x0002
USB Bus Reset interrupt vector
0x0004
128-s timer interrupt vector
0x0006
1.024-ms timer interrupt vector
0x0008
USB endpoint 0 interrupt vector
0x000A
USB endpoint 1 interrupt vector
0x000C
USB endpoint 2 interrupt vector
0x000E
SPI interrupt vector
0x0010
Capture timer A interrupt Vector
0x0012
Capture timer B interrupt vector
0x0014
GPIO interrupt vector
0x0016
Wake-up interrupt vector
0x0018
Program Memory begins here
0x1FDF
8 KB PROM ends here (8K - 32 bytes). See Note below
Figure 1. Program Memory Space with Interrupt Vector Table
Note
1. The upper 32 bytes of the 8K PROM are reserved. Therefore, the user’s program must not overwrite this space.
Document #: 38-08022 Rev. *E
Page 7 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Data Memory Organization
The CY7C637xxC microcontrollers provide 256 bytes of data RAM. In normal usage, the SRAM is partitioned into four areas: program
stack, data stack, user variables and USB endpoint FIFOs as shown below.
Figure 2. Data Memory Organization
After reset
8-bit DSP
8-bit PSP
Address
0x00
Program Stack Growth
User Selected
Data Stack Growth
(User’s firmware moves DSP)
8-bit DSP
User Variables
0xE8
USB FIFO for Address A endpoint 2
0xF0
USB FIFO for Address A endpoint 1
0xF8
USB FIFO for Address A endpoint 0
Top of RAM Memory
0xFF
I/O Register Summary
I/O registers are accessed via the I/O Read (IORD) and I/O Write
(IOWR, IOWX) instructions. IORD reads the selected port into
the accumulator. IOWR writes data from the accumulator to the
selected port. Indexed I/O Write (IOWX) adds the contents of X
to the address in the instruction to form the port address and
writes data from the accumulator to the specified port. Note that
specifying address 0 with IOWX (e.g., IOWX 0h) means the I/O
port is selected solely by the contents of X.
Note: All bits of all registers are cleared to all zeros on reset,
except the Processor Status and Control Register (Figure 33). All
registers not listed are reserved, and should never be written by
firmware. All bits marked as reserved should always be written
as 0 and be treated as undefined by reads.
Table 1. I/O Register Summary
Register Name
I/O Address
Read/Write
Function
Fig
Port 0 Data
0x00
R/W
GPIO Port 0
7
Port 1 Data
0x01
R/W
GPIO Port 1
8
Port 2 Data
0x02
R
Auxiliary input register for D+, D–, VREG, XTALIN
Port 0 Interrupt Enable
0x04
W
Interrupt enable for pins in Port 0
37
Port 1 Interrupt Enable
0x05
W
Interrupt enable for pins in Port 1
38
Port 0 Interrupt Polarity
0x06
W
Interrupt polarity for pins in Port 0
39
Port 1 Interrupt Polarity
0x07
W
Interrupt polarity for pins in Port 1
Port 0 Mode0
0x0A
W
Controls output configuration for Port 0
9
Controls output configuration for Port 1
11
Port 0 Mode1
0x0B
W
Port 1 Mode0
0x0C
W
Port 1 Mode1
0x0D
W
Document #: 38-08022 Rev. *E
12
Page 8 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Table 1. I/O Register Summary (continued)
Register Name
USB Device Address
I/O Address
Read/Write
0x10
R/W
Function
USB Device Address register
Fig
15
EP0 Counter Register
0x11
R/W
USB Endpoint 0 counter register
18
EP0 Mode Register
0x12
R/W
USB Endpoint 0 configuration register
16
18
EP1 Counter Register
0x13
R/W
USB Endpoint 1 counter register
EP1 Mode Register
0x14
R/W
USB Endpoint 1 configuration register
EP2 Counter Register
0x15
R/W
USB Endpoint 2 counter register
EP2 Mode Register
0x16
R/W
USB Endpoint 2 configuration register
USB Status & Control
0x1F
R/W
USB status and control register
Global Interrupt Enable
0x20
R/W
Global interrupt enable register
Endpoint Interrupt Enable
0x21
R/W
USB endpoint interrupt enables
Timer (LSB)
0x24
R
Lower 8 bits of free-running timer (1 MHz)
24
Timer (MSB)
0x25
R
Upper 4 bits of free-running timer
25
WDR Clear
0x26
W
Watchdog Reset clear
Capture Timer A Rising
0x40
R
Rising edge Capture Timer A data register
Capture Timer A Falling
0x41
R
Falling edge Capture Timer A data register
Capture Timer B Rising
0x42
R
Rising edge Capture Timer B data register
29
Capture Timer B Falling
0x43
R
Falling edge Capture Timer B data register
30
Capture TImer Configuration
0x44
R/W
Capture Timer Status
0x45
R
SPI Data
0x60
SPI Control
0x61
14
-
Capture Timer configuration register
32
Capture Timer status register
31
R/W
SPI read and write data register
21
R/W
SPI status and control register
22
Clock Configuration
0xF8
R/W
Internal / External Clock configuration register
Processor Status & Control
0xFF
R/W
Processor status and control
Document #: 38-08022 Rev. *E
18
33
Page 9 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Clocking
The chip can be clocked from either the internal on-chip clock, or from an oscillator based on an external resonator/crystal, as shown
in Figure . No additional capacitance is included on chip at the XTALIN/OUT pins. Operation is controlled by the Clock Configuration
Register, Figure .
Figure 3. Clock Oscillator On-chip Circuit
Int Clk Output Disable
XTALOUT
Internal Osc
Ext Clk Enable
Clock
Doubler
Clk2x (12 MHz)
(to Microcontroller)
XTALIN
Clk1x (6 MHz)
(to USB SIE)
Port 2.1
Figure 4. Clock Configuration Register (Address 0xF8)
Bit #
7
6
5
Bit Name
Ext. Clock
Resume
Delay
Read/Write
R/W
R/W
R/W
Reset
0
0
0
3
2
1
0
Low-voltage
Reset
Disable
Precision
USB
Clocking
Enable
Internal
Clock
Output
Disable
External
Oscillator
Enable
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
Wake-up Timer Adjust Bit [2:0]
Bit 7: Ext. Clock Resume Delay
External Clock Resume Delay bit selects the delay time when
switching to the external oscillator from the internal oscillator
mode, or when waking from suspend mode with the external
oscillator enabled.
1 = 4 ms delay.
0 = 128 s delay.
The delay gives the oscillator time to start up. The shorter time
is adequate for operation with ceramic resonators, while the
longer time is preferred for start-up with a crystal. (These
times do not include an initial oscillator start-up time which
depends on the resonating element. This time is typically
50–100 s for ceramic resonators and 1–10 ms for crystals).
Note that this bit only selects the delay time for the external
clock mode. When waking from suspend mode with the internal oscillator (Bit 0 is LOW), the delay time is only 8 s in
Document #: 38-08022 Rev. *E
4
addition to a delay of approximately 1 s for the oscillator to
start.
Bit [6:4]: Wake-up Timer Adjust Bit [2:0]
The Wake-up Timer Adjust Bits are used to adjust the
Wake-up timer period.
If the Wake-up interrupt is enabled in the Global Interrupt Enable Register, the microcontroller will generate wake-up interrupts periodically. The frequency of these periodical wake-up
interrupts is adjusted by setting the Wake-up Timer Adjust Bit
[2:0], as described in Section . One common use of the
wake-up interrupts is to generate periodical wake-up events
during suspend mode to check for changes, such as looking
for movement in a mouse, while maintaining a low average
power.
Page 10 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Bit 3: Low-voltage Reset Disable
When VCC drops below VLVR (see Section for the value of
VLVR) and the Low-voltage Reset circuit is enabled, the microcontroller enters a partial suspend state for a period of tSTART
(see Section for the value of tSTART). Program execution begins from address 0x0000 after this tSTART delay period. This
provides time for VCC to stabilize before the part executes
code. See Section for more details.
1 = Disables the LVR circuit.
0 = Enables the LVR circuit.
Bit 2: Precision USB Clocking Enable
The Precision USB Clocking Enable only affects operation in
internal oscillator mode. In that mode, this bit must be set
to 1 to cause the internal clock to automatically precisely
tune to USB timing requirements (6 MHz ±1.5%). The frequency may have a looser initial tolerance at power-up, but
all USB transmissions from the chip will meet the USB specification.
1 = Enabled. The internal clock accuracy is 6 MHz ±1.5% after
USB traffic is received.
0 = Disabled. The internal clock accuracy is 6 MHz ±5%.
Bit 1: Internal Clock Output Disable
The Internal Clock Output Disable is used to keep the internal
clock from driving out to the XTALOUT pin. This bit has no
effect in the external oscillator mode.
1 = Disable internal clock output. XTALOUT pin will drive
HIGH.
0 = Enable the internal clock output. The internal clock is driven out to the XTALOUT pin.
Bit 0: External Oscillator Enable
At power-up, the chip operates from the internal clock by default. Setting the External Oscillator Enable bit HIGH disables
the internal clock, and halts the part while the external resonator/crystal oscillator is started. Clearing this bit has no immediate effect, although the state of this bit is used when
waking out of suspend mode to select between internal and
external clock. In internal clock mode, XTALIN pin will be configured as an input with a weak pull-down and can be used as
a GPIO input (P2.1).
1 = Enable the external oscillator. The clock is switched to
external clock mode, as described in Section .
0 = Enable the internal oscillator.
Internal/External Oscillator Operation
The internal oscillator provides an operating clock, factory set to
a nominal frequency of 6 MHz. This clock requires no external
components. At power-up, the chip operates from the internal
clock. In this mode, the internal clock is buffered and driven to
the XTALOUT pin by default, and the state of the XTALIN pin can
be read at Port 2.1. While the internal clock is enabled, its output
can be disabled at the XTALOUT pin by setting the Internal Clock
Output Disable bit of the Clock Configuration Register.
Setting the External Oscillator Enable bit of the Clock Configuration Register HIGH disables the internal clock, and halts the
part while the external resonator/crystal oscillator is started. The
Document #: 38-08022 Rev. *E
steps involved in switching from Internal to External Clock mode
are as follows:
1. At reset, chip begins operation using the internal clock.
2. Firmware sets Bit 0 of the Clock Configuration Register. For
example,
mov A, 1h
; Set Bit 0 HIGH (External Oscillator
Enable bit). Bit 7 cleared gives
faster start-up
iowr F8h
; Write to Clock Configuration
Register
3. Internal clocking is halted, the internal oscillator is disabled,
and the external clock oscillator is enabled.
4. After the external clock becomes stable, chip clocks are
re-enabled using the external clock signal. (Note that the time
for the external clock to become stable depends on the
external resonating device; see next section.)
5. After an additional delay the CPU is released to run. This
delay depends on the state of the Ext. Clock Resume Delay
bit of the Clock Configuration Register. The time is 128 s if
the bit is 0, or 4 ms if the bit is 1.
6. Once the chip has been set to external oscillator, it can only
return to internal clock when waking from suspend mode.
Clearing bit 0 of the Clock Configuration Register will not
re-enable internal clock mode until suspend mode is entered.
See Section for more details on suspend mode operation.
If the Internal Clock is enabled, the XTALIN pin can serve as a
general purpose input, and its state can be read at Port 2, Bit 1
(P2.1). Refer to Figure for the Port 2 Data Register. In this mode,
there is a weak pull-down at the XTALIN pin. This input cannot
provide an interrupt source to the CPU.
External Oscillator
The user can connect a low-cost ceramic resonator or an
external oscillator to the XTALIN/XTALOUT pins to provide a
precise reference frequency for the chip clock, as shown in
Figure . The external components required are a ceramic
resonator or crystal and any associated capacitors. To run from
the external resonator, the External Oscillator Enable bit of the
Clock Configuration Register must be set to 1, as explained in
the previous section.
Start-up times for the external oscillator depend on the
resonating device. Ceramic resonator based oscillators typically
start in less than 100 s, while crystal based oscillators take
longer, typically 1 to 10 ms. Board capacitance should be
minimized on the XTALIN and XTALOUT pins by keeping the
traces as short as possible.
An external 6-MHz clock can be applied to the XTALIN pin if the
XTALOUT pin is left open.
Reset
The USB Controller supports three types of resets. The effects
of the reset are listed below. The reset types are:
1. Low-voltage Reset (LVR)
2. Brown Out Reset (BOR)
3. Watchdog Reset (WDR)
The occurrence of a reset is recorded in the Processor Status
and Control Register (Figure 33). Bits 4 (Low-voltage or
Page 11 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Brown-out Reset bit) and 6 (Watchdog Reset bit) are used to
record the occurrence of LVR/BOR and WDR respectively. The
firmware can interrogate these bits to determine the cause of a
reset.
The microcontroller begins execution from ROM address 0x0000
after a LVR, BOR, or WDR reset. Although this looks like interrupt
vector 0, there is an important difference. Reset processing does
NOT push the program counter, carry flag, and zero flag onto
program stack. Attempting to execute either a RET or RETI in
the reset handler will cause unpredictable execution results.
The following events take place on reset. More details on the
various resets are given in the following sections.
1. All registers are reset to their default states (all bits cleared,
except in Processor Status and Control Register).
2. GPIO and USB pins are set to high-impedance state.
3. The VREG pin is set to high-impedance state.
4. Interrupts are disabled.
5. USB operation is disabled and must be enabled by firmware
if desired, as explained in Section .
6. For a BOR or LVR, the external oscillator is disabled and
Internal Clock mode is activated, followed by a time-out period
tSTART for VCC to stabilize. A WDR does not change the clock
mode, and there is no delay for VCC stabilization on a WDR.
Note that the External Oscillator Enable (Bit 0, Figure ) will be
cleared by a WDR, but it does not take effect until suspend
mode is entered.
7. The Program Stack Pointer (PSP) and Data Stack Pointer
(DSP) reset to address 0x00. Firmware should move the DSP
for USB applications, as explained in Section .
8. Program execution begins at address 0x0000 after the appropriate time-out period.
Low-voltage Reset (LVR)
When VCC is first applied to the chip, the internal oscillator is
started and the Low-voltage Reset is initially enabled by default.
At the point where VCC has risen above VLVR (see Section for
the value of VLVR), an internal counter starts counting for a period
of tSTART (see Section for the value of tSTART). During this tSTART
time, the microcontroller enters a partial suspend state to wait for
VCC to stabilize before it begins executing code from address
0x0000.
As long as the LVR circuit is enabled, this reset sequence
repeats whenever the VCC pin voltage drops below VLVR. The
LVR can be disabled by firmware by setting the Low-voltage
Reset Disable bit in the Clock Configuration Register (Figure ).
In addition, the LVR is automatically disabled in suspend mode
to save power. If the LVR was enabled before entering suspend
mode, it becomes active again once the suspend mode ends.
When LVR is disabled during normal operation (i.e., by writing ‘0’
to the Low-voltage Reset Disable bit in the Clock Configuration
Register), the chip may enter an unknown state if VCC drops
below VLVR. Therefore, LVR should be enabled at all times
during normal operation. If LVR is disabled (i.e., by firmware or
during suspend mode), a secondary low-voltage monitor, BOR,
becomes active, as described in the next section. The LVR/BOR
Reset bit of the Processor Status and Control Register
(Figure 33), is set to ‘1’ if either a LVR or BOR has occurred.
Brown Out Reset (BOR)
The Brown Out Reset (BOR) circuit is always active and behaves
like the POR. BOR is asserted whenever the VCC voltage to the
device is below an internally defined trip voltage of approximately
2.5V. The BOR re-enables LVR. That is, once VCC drops and
trips BOR, the part remains in reset until VCC rises above VLVR.
At that point, the tSTART delay occurs before normal operation
resumes, and the microcontroller starts executing code from
address 0x00 after the tSTART delay.
In suspend mode, only the BOR detection is active, giving a reset
if VCC drops below approximately 2.5V. Since the device is
suspended and code is not executing, this lower reset voltage is
safe for retaining the state of all registers and memory. Note that
in suspend mode, LVR is disabled as discussed in Section .
Watchdog Reset (WDR)
The Watchdog Timer Reset (WDR) occurs when the internal
Watchdog timer rolls over. Writing any value to the write-only
Watchdog Reset Register at address 0x26 will clear the timer.
The timer will roll over and WDR will occur if it is not cleared
within tWATCH (see Figure 10) of the last clear. Bit 6 (Watchdog
Reset bit) of the Processor Status and Control Register is set to
record this event (see Section for more details). A Watchdog
Timer Reset typically lasts for 2–4 ms, after which the microcontroller begins execution at ROM address 0x0000.
Figure 5. Watchdog Reset (WDR, Address 0x26)
tWATCH = 10.1 to
14.6 ms
WDR
(at FOSC = 6 MHz)
2–4 ms
At least 10.1 ms
since last write to WDR
Document #: 38-08022 Rev. *E
WDR goes HIGH
for 2–4 ms
Execution begins at
ROM Address 0x0000
Page 12 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Suspend Mode
The CY7C637xxC parts support a versatile low-power suspend
mode. In suspend mode, only an enabled interrupt or a LOW
state on the D–/SDATA pin will wake the part. Two options are
available. For lowest power, all internal circuits can be disabled,
so only an external event will resume operation. Alternatively, a
low-power internal wake-up timer can be used to trigger the
wake-up interrupt. This timer is described in Section , and can be
used to periodically poll the system to check for changes, such
as looking for movement in a mouse, while maintaining a low
average power.
The CY7C637xxC is placed into a low-power state by setting the
Suspend bit of the Processor Status and Control Register
(Figure 33). All logic blocks in the device are turned off except
the GPIO interrupt logic, the D–/SDATA pin input receiver, and
(optionally) the wake-up timer. The clock oscillators, as well as
the free-running and Watchdog timers are shut down. Only the
occurrence of an enabled GPIO interrupt, wake-up interrupt, SPI
slave interrupt, or a LOW state on the D–/SDATA pin will wake
the part from suspend (D– LOW indicates non-idle USB activity).
Once one of these resuming conditions occurs, clocks will be
restarted and the device returns to full operation after the oscillator is stable and the selected delay period expires. This delay
period is determined by selection of internal vs. external clock,
and by the state of the Ext. Clock Resume Delay as explained in
Section .
In suspend mode, any enabled and pending interrupt will wake
the part up. The state of the Interrupt Enable Sense bit (Bit 2,
Figure 33) does not have any effect. As a result, any interrupts
not intended for waking from suspend should be disabled
through the Global Interrupt Enable Register and the USB End
Point Interrupt Enable Register (Section ).
If a resuming condition exists when the suspend bit is set, the
part will still go into suspend and then awake after the appropriate delay time. The Run bit in the Processor Status and
Control Register must be set for the part to resume out of
suspend.
Once the clock is stable and the delay time has expired, the
microcontroller will execute the instruction following the I/O write
that placed the device into suspend mode before servicing any
interrupt requests.
To achieve the lowest possible current during suspend mode, all
I/O should be held at either VCC or ground. In addition, the GPIO
bit interrupts (Figure 37 and Figure 38) should be disabled for
any pins that are not being used for a wake-up interrupt. This
should be done even if the main GPIO Interrupt Enable (Figure )
is off.
Typical code for entering suspend is shown below:
...
; All GPIO set to low-power state (no floating
pins, and bit interrupts disabled unless using
for wake-up)
...
; Enable GPIO and/or wake-up timer
interrupts if desired for wake-up
...
; Select clock mode for wake-up (see Section )
mov a, 09h
; Set suspend and run bits
iowr FFh
; Write to Status and Control Register – Enter
suspend, wait for GPIO/wake-up interrupt or
USB activity
nop
; This executes before any ISR
...
; Remaining code for exiting suspend routine
Document #: 38-08022 Rev. *E
Clocking Mode on Wake-up from Suspend
When exiting suspend on a wake-up event, the device can be
configured to run in either Internal or External Clock mode. The
mode is selected by the state of the External Oscillator Enable
bit in the Clock Configuration Register (Figure ). Using the
Internal Clock saves the external oscillator start-up time and
keeps that oscillator off for additional power savings. The
external oscillator mode can be activated when desired, similar
to operation at power-up.
The sequence of events for these modes is as follows:
Wake in Internal Clock Mode:
1. Before entering suspend, clear bit 0 of the Clock Configuration
Register. This selects Internal clock mode after suspend.
2. Enter suspend mode by setting the suspend bit of the
Processor Status and Control Register.
3. After a wake-up event, the internal clock starts immediately
(within 2 s).
4. A time-out period of 8 s passes, and then firmware execution
begins.
5. At some later point, to activate External Clock mode, set bit 0
of the Clock Configuration Register. This halts the internal
clocks while the external clock becomes stable. After an
additional time-out (128 s or 4 ms, see Section ), firmware
execution resumes.
Wake in External Clock Mode:
1. Before entering suspend, the external clock must be selected
by setting bit 0 of the Clock Configuration Register. Make sure
this bit is still set when suspend mode is entered. This selects
External clock mode after suspend.
2. Enter suspend mode by setting the suspend bit of the
Processor Status and Control Register.
3. After a wake-up event, the external oscillator is started. The
clock is monitored for stability (this takes approximately
50–100 s with a ceramic resonator).
4. After an additional time-out period (128 s or 4 ms, see
Section ), firmware execution resumes.
Wake-up Timer
The wake-up timer runs whenever the wake-up interrupt is
enabled, and is turned off whenever that interrupt is disabled.
Operation is independent of whether the device is in suspend
mode or if the global interrupt bit is enabled. Only the Wake-up
Timer Interrupt Enable bit (Figure ) controls the wake-up timer.
Once this timer is activated, it will give interrupts after its time-out
period (see below). These interrupts continue periodically until
the interrupt is disabled. Whenever the interrupt is disabled, the
wake-up timer is reset, so that a subsequent enable always
results in a full wake-up time.
The wake-up timer can be adjusted by the user through the
Wake-up Timer Adjust bits in the Clock Configuration Register
(Figure ). These bits clear on reset. In addition to allowing the
user to select a range for the wake-up time, a firmware algorithm
can be used to tune out initial process and operating condition
variations in this wake-up time. This can be done by timing the
wake-up interrupt time with the accurate 1.024-ms timer
interrupt, and adjusting the Timer Adjust bits accordingly to
approximate the desired wake-up time.
Page 13 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Table 2. Wake-up Timer Adjust Settings
Adjust Bits [2:0]
(Bits [6:4] in Figure )
Wakeup Time
000 (reset state)
1 * tWAKE
001
2 * tWAKE
010
4 * tWAKE
011
8 * tWAKE
100
16 * tWAKE
101
32 * tWAKE
110
64 * tWAKE
111
128 * tWAKE
See Switching Characteristics on page 43 for the value of
tWAKE
General Purpose I/O Ports
Ports 0 and 1 provide up to 16 versatile GPIO pins that can be read or written (the number of pins depends on package type). Figure
shows a diagram of a GPIO port pin.
Figure 6. Block Diagram of GPIO Port (one pin shown)
VCC
2
GPIO
Mode
SPI Bypass (P0.5–P0.7 only)
Q1
Control
(=1 if SPI inactive, or for non-SPI pins)
Data
Out
Register
Internal
Data Bus
Q3
14 k
GPIO
Pin
Q2
Port Write
(Data Reg must be 1
for SPI outputs)
Threshold Select
Port Read
Interrupt
Polarity
Interrupt
Enable
Interrupt
Logic
To Capture Timers (P0.0, P0.1)
and SPI (P0.4–P0.7))
To Interrupt
Controller
Port 0 is an 8-bit port; Port 1 contains either 2 bits, P1.1–P1.0 in
the CY7C63723C, or all 8 bits, P1.7–P1.0 in the CY7C63743C
parts. Each bit can also be selected as an interrupt source for the
microcontroller, as explained in Section .
Each GPIO pin is configured independently. The driving state of
each GPIO pin is determined by the value written to the pin’s
Data Register and by two associated pin’s Mode0 and Mode1
bits.
The data for each GPIO pin is accessible through the Port Data
register. Writes to the Port Data register store outgoing data state
for the port pins, while reads from the Port Data register return
the actual logic value on the port pins, not the Port Data register
contents.
The Port 0 Data Register is shown in Figure 7, and the Port 1
Data Register is shown in Figure 8. The Mode0 and Mode1 bits
for the two GPIO ports are given in Figure 9 through Figure 12.
Document #: 38-08022 Rev. *E
Page 14 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Bit [7:0]: P0[7:0] Mode 1
Figure 7. Port 0 Data (Address 0x00)
1 = Port Pin Mode 1 is logic HIGH
Bit #
7
6
5
4
Bit Name
3
2
1
0 = Port Pin Mode 1 is logic LOW
0
Figure 11. GPIO Port 1 Mode0 Register (Address 0x0C)
P0
Read/Write R/W R/W R/W R/W R/W R/W R/W R/W
Reset
0
0
0
0
0
0
0
Bit #
0
7
6
5
Read/Write
W
W
W
W
Reset
0
0
0
0
Bit Name
Bit [7:0]: P0[7:0]
4
3
2
1
0
W
W
W
W
0
0
0
0
P1[7:0] Mode0
1 = Port Pin is logic HIGH
0 = Port Pin is logic LOW
Bit [7:0]: P1[7:0] Mode 0
Figure 8. Port 1 Data (Address 0x01)
1 = Port Pin Mode 0 is logic HIGH
Bit #
7
6
5
4
Bit Name
3
2
1
Figure 12. GPIO Port 1 Mode1 Register (Address 0x0D)
P1
Notes
0 = Port Pin Mode 0 is logic LOW
0
Pins 7:2 only in CY7C63743C
Pins 1:0 in
all parts
Bit #
Read/Write R/W R/W R/W R/W R/W R/W R/W R/W
Reset
0
0
0
0
0
0
0
7
6
5
Bit Name
0
4
3
2
1
0
P1[7:0] Mode1
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Bit [7:0]: P1[7:0]
1 = Port Pin is logic HIGH
Bit [7:0]: P1[7:0] Mode 1
0 = Port Pin is logic LOW
1 = Port Pin Mode 1 is logic HIGH
Figure 9. GPIO Port 0 Mode0 Register (Address 0x0A)
Bit #
7
6
5
Bit Name
4
3
0 = Port Pin Mode 1 is logic LOW
2
1
0
P0[7:0] Mode0
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Each pin can be independently configured as high-impedance
inputs, inputs with internal pull-ups, open drain outputs, or traditional CMOS outputs with selectable drive strengths.
The driving state of each GPIO pin is determined by the value
written to the pin’s Data Register and by its associated Mode0
and Mode1 bits. Table 3 lists the configuration states based on
these bits. The GPIO ports default on reset to all Data and Mode
Registers cleared, so the pins are all in a high-impedance state.
The available GPIO output drive strength are:
■
Bit [7:0]: P0[7:0] Mode 0
Q1, Q2, and Q3 (Figure ) are OFF. The GPIO pin is not driven
internally. Performing a read from the Port Data Register return the actual logic value on the port pins.
1 = Port 0 Mode 0 is logic HIGH
0 = Port 0 Mode 0 is logic LOW
Figure 10. GPIO Port 0 Mode1 Register (Address 0x0B)
Bit #
7
6
5
Bit Name
4
3
2
1
0
■
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Low Sink Mode (Mode1 = 1, Mode0 = 0, and the pin’s Data
Register = 0)
Q1 and Q3 are OFF. Q2 is ON. The GPIO pin is capable of
sinking 2 mA of current.
P0[7:0] Mode1
Document #: 38-08022 Rev. *E
Hi-Z Mode (Mode1 = 0 and Mode0 = 0)
■
Medium Sink Mode (Mode1 = 0, Mode0 = 1, and the pin’s Data
Register = 0)
Q1 and Q3 are OFF. Q2 is ON. The GPIO pin is capable of
sinking 8 mA of current.
Page 15 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
■
High Sink Mode (Mode1 = 1, Mode0 = 1, and the pin’s Data
Register = 0)
Q1 and Q3 are OFF. Q2 is ON. The GPIO pin is capable of
sinking 50 mA of current.
■
Bit [7:6]: Reserved
Bit [5:4]: D+ (SCLK) and D– (SDATA) States
The state of the D+ and D– pins can be read at Port 2 Data
Register. Performing a read from the port pins returns their
logic values.
High Drive Mode (Mode1 = 0 or 1, Mode0 = 1, and the pin’s
Data Register = 1)
1 = Port Pin is logic HIGH
Q1 and Q2 are OFF. Q3 is ON. The GPIO pin is capable of
sourcing 2 mA of current.
■
Resistive Mode (Mode1 = 1, Mode0 = 0, and the pin’s Data
Register = 1)
Q2 and Q3 are OFF. Q1 is ON. The GPIO pin is pulled up with
an internal 14-kresistor.
0 = Port Pin is logic LOW
Bit [3:2]: Reserved
Bit 1: P2.1 (Internal Clock Mode Only)
In the Internal Clock mode, the XTALIN pin can serve as a
general purpose input, and its state can be read at Port 2, Bit
1 (P2.1). See Section for more details.
Note that open drain mode can be achieved by fixing the Data
and Mode1 Registers LOW, and switching the Mode0 register.
Input thresholds are CMOS, or TTL as shown in the table (See
Section for the input threshold voltage in TTL or CMOS modes).
Both input modes include hysteresis to minimize noise sensitivity. In suspend mode, if a pin is used for a wake-up interrupt
using an external R-C circuit, CMOS mode is preferred for lowest
power.
Table 3. Ports 0 and 1 Output Control Truth Table
Data
Register
Drive
Input
Mode1 Mode0 Output
Strength
Threshold
0
Hi-Z
CMOS
Hi-Z
TTL
0
0
0
1
Medium
(8 mA) Sink
CMOS
1
High Drive
CMOS
0
0
Low (2 mA)
Sink
CMOS
Resistive
CMOS
High (50 mA)
Sink
High Drive
1
0
1 = Port Pin is logic HIGH
0 = Port Pin is logic LOW
Bit 0: P2.0/VREG Pin State
In PS/2 mode, the VREG pin can be used as an input and its
state can be read at port P2.0. Section for more details.
1 = Port Pin is logic HIGH
0 = Port Pin is logic LOW
USB Serial Interface Engine (SIE)
The SIE allows the microcontroller to communicate with the USB
host. The SIE simplifies the interface between the microcontroller and USB by incorporating hardware that handles the
following USB bus activity independently of the microcontroller:
■
Translate the encoded received data and format the data to be
transmitted on the bus.
■
CRC checking and generation. Flag the microcontroller if errors
exist during transmission.
CMOS
■
Address checking. Ignore the transactions not addressed to
the device.
CMOS
■
Send appropriate ACK/NAK/STALL handshakes.
Auxiliary Input Port
■
Port 2 serves as an auxiliary input port as shown in Figure . The
Port 2 inputs all have TTL input thresholds.
Token type identification (SETUP, IN, or OUT). Set the appropriate token bit once a valid token is received.
■
Place valid received data in the appropriate endpoint FIFOs.
Figure 13. Port 2 Data Register (Address 0x02)
■
Send and update the data toggle bit (Data1/0).
■
Bit stuffing/unstuffing.
1
1
0
1
1
1
Bit #
7
6
5
4
3
2
1
0
P2.0
Reserved P2.1
D–
Bit Reserved D+
(Internal VREG
Name
(SCLK) (SDATA)
Pin
Clock
State
State
Mode State
Only)
Read/
Write
-
-
R
R
-
-
R
R
Reset
0
0
0
0
0
0
0
0
Document #: 38-08022 Rev. *E
Firmware is required to handle the rest of the USB interface with
the following tasks:
■
Coordinate enumeration by decoding USB device requests.
■
Fill and empty the FIFOs.
■
Suspend/Resume coordination.
■
Verify and select Data toggle values.
Page 16 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
USB Enumeration
to approximately 1 Volt above VREG if the VREG Enable bit is
set, or if the Device Address is enabled (bit 7 of the USB
Device Address Register, Figure 15).
A typical USB enumeration sequence is shown below. In this
description, ‘Firmware’ refers to embedded firmware in the
CY7C637xxC controller.
1. The host computer sends a SETUP packet followed by a
DATA packet to USB address 0 requesting the Device descriptor.
2. Firmware decodes the request and retrieves its Device
descriptor from the program memory tables.
3. The host computer performs a control read sequence and
Firmware responds by sending the Device descriptor over the
USB bus, via the on-chip FIFO.
4. After receiving the descriptor, the host sends a SETUP packet
followed by a DATA packet to address 0 assigning a new USB
address to the device.
5. Firmware stores the new address in its USB Device Address
Register after the no-data control sequence completes.
6. The host sends a request for the Device descriptor using the
new USB address.
7. Firmware decodes the request and retrieves the Device
descriptor from program memory tables.
8. The host performs a control read sequence and Firmware
responds by sending its Device descriptor over the USB bus.
9. The host generates control reads from the device to request
the Configuration and Report descriptors.
10.Once the device receives a Set Configuration request, its
functions may now be used.
11.Firmware should take appropriate action for Endpoint 1
and/or 2 transactions, which may occur from this point.
Bit 4: Reserved. Must be written as a ‘0’.
USB Port Status and Control
Bit 3: USB Bus Activity
USB status and control is regulated by the USB Status and
Control Register as shown in Figure 14.
Figure 14. USB Status and Control Register (Address 0x1F)
Bit #
7
6
5
4
3
2:0
Bit PS/2 VREG USB Reserved USB
D+/D–
Name Pull-up Enable ResetBus
Forcing
Enable
PS/2
Activity
Bit
Activity
Interrupt
Mode
Read/ R/W
Write
Reset
0
R/W
R/W
-
R/W
R/W
0
0
0
0
0 0 0
Bit 7: PS/2 Pull-up Enable
This bit is used to enable the internal PS/2 pull-up resistors
on the SDATA and SCLK pins. Normally the output high level
on these pins is VCC, but note that the output will be clamped
Document #: 38-08022 Rev. *E
1 = Enable PS/2 Pull-up resistors. The SDATA and SCLK pins
are pulled up internally to VCC with two resistors of approximately 5 k (see Section for the value of RPS2).
0 = Disable PS/2 Pull-up resistors.
Bit 6: VREG Enable
A 3.3V voltage regulator is integrated on chip to provide a
voltage source for a 1.5-k pull-up resistor connected to the
D– pin as required by the USB Specification. Note that the
VREG output has an internal series resistance of approximately 200, the external pull-up resistor required is approximately 1.3-k (see Figure 19).
1 = Enable the 3.3V output voltage on the VREG pin.
0 = Disable. The VREG pin can be configured as an input.
Bit 5: USB-PS/2 Interrupt Select
This bit allows the user to select whether an USB bus reset
interrupt or a PS/2 activity interrupt will be generated when
the interrupt conditions are detected.
1 = PS/2 interrupt mode. A PS/2 activity interrupt will occur if
the SDATA pin is continuously LOW for 128 to 256 s.
0 = USB interrupt mode (default state). In this mode, a USB
bus reset interrupt will occur if the single ended zero (SE0, D–
and D+ are LOW) exists for 128 to 256 s.
See Section for more details.
The Bus Activity bit is a “sticky” bit that detects any non-idle
USB event has occurred on the USB bus. Once set to HIGH
by the SIE to indicate the bus activity, this bit retains its logical
HIGH value until firmware clears it. Writing a ‘0’ to this bit
clears it; writing a ‘1’ preserves its value. The user firmware
should check and clear this bit periodically to detect any loss
of bus activity. Firmware can clear the Bus Activity bit, but only
the SIE can set it. The 1.024-ms timer interrupt service routine
is normally used to check and clear the Bus Activity bit.
1 = There has been bus activity since the last time this bit was
cleared. This bit is set by the SIE.
0 = No bus activity since last time this bit was cleared (by
firmware).
Bit [2:0]: D+/D– Forcing Bit [2:0]
Forcing bits allow firmware to directly drive the D+ and D–
pins, as shown in Table 4. Outputs are driven with controlled
edge rates in these modes for low EMI. For forcing the D+ and
D– pins in USB mode, D+/D– Forcing Bit 2 should be 0. Setting D+/D– Forcing Bit 2 to ‘1’ puts both pins in an open-drain
mode, preferred for applications such as PS/2 or LED driving.
Page 17 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
USB Control Endpoint
Table 4. Control Modes to Force D+/D– Outputs
D+/D–
Forcing Bit
[2:0]
Control Action
Application
000
Not forcing (SIE controls
driver)
Any Mode
001
Force K (D+ HIGH, D– LOW)
USB Mode
010
Force J (D+ LOW, D– HIGH)
011
Force SE0 (D– LOW, D+
LOW)
100
Force D– LOW, D+ LOW
101
Force D– LOW, D+ HiZ
110
Force D– HiZ, D+ LOW
111
Force D– HiZ, D+ HiZ
All USB devices are required to have an endpoint number 0
(EP0) that is used to initialize and control the USB device. EP0
provides access to the device configuration information and
allows generic USB status and control accesses. EP0 is bidirectional as the device can both receive and transmit data. EP0
uses an 8-byte FIFO at SRAM locations 0xF8-0xFF, as shown in
Section .
The EP0 endpoint mode register uses the format shown in
Figure 16.
Bit #
PS/2
Mode[2]
USB Device
7
6
5
4
3:0
Bit
SETUP
IN
OUT
ACKed
Mode Bit
Name Received Received Received Transaction
Read/
Write
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0 0 0 0
Figure 16. Endpoint 0 Mode Register (Address 0x12)
The CY7C637xxC supports one USB Device Address with three
endpoints: EP0, EP1, and EP2.
USB Address Register
The USB Device Address Register contains a 7-bit USB address
and one bit to enable USB communication. This register is
cleared during a reset, setting the USB device address to zero
and marking this address as disabled. Figure 15 shows the
format of the USB Address Register.
Bit #
7
6
5
4
3
2
1
0
Bit Name
Device
Address
Enable
Device Address
Read/Write
R/W
R/W R/W R/W R/W R/W R/W R/W
Reset
0
The SIE provides a locking feature to prevent firmware from
overwriting bits in the USB Endpoint 0 Mode Register. Writes to
the register have no effect from the point that Bit[6:0] of the
register are updated (by the SIE) until the firmware reads this
register. The CPU can unlock this register by reading it.
Because of these hardware-locking features, firmware should
perform an read after a write to the USB Endpoint 0 Mode
Register and USB Endpoint 0 Count Register (Figure 18) to
verify that the contents have changed as desired, and that the
SIE has not updated these values.
Bit [7:4] of this register are cleared by any non-locked write to
this register, regardless of the value written.
Bit 7: SETUP Received
0
0
0
0
0
0
0
Figure 15. USB Device Address Register (Address 0x10)
In either USB or PS/2 mode, this register is cleared by both hardware resets and the USB bus reset. See Section for more information on the USB Bus Reset – PS/2 interrupt.
Bit 7: Device Address Enable
This bit must be enabled by firmware before the serial interface engine (SIE) will respond to USB traffic at the address
specified in Bit [6:0].
1 = Enable USB device address.
0 = Disable USB device address.
Bit [6:0]: Device Address Bit [6:0]
1 = A valid SETUP packet has been received. This bit is
forced HIGH from the start of the data packet phase of the
SETUP transaction until the start of the ACK packet returned
by the SIE. The CPU is prevented from clearing this bit during
this interval. While this bit is set to ‘1’, the CPU cannot write
to the EP0 FIFO. This prevents firmware from overwriting an
incoming SETUP transaction before firmware has a chance
to read the SETUP data.
0 = No SETUP received. This bit is cleared by any non-locked
writes to the register.
Bit 6: IN Received
1 = A valid IN packet has been received. This bit is updated
to ‘1’ after the last received packet in an IN transaction. This
bit is cleared by any non-locked writes to the register.
0 = No IN received. This bit is cleared by any non-locked
writes to the register.
These bits must be set by firmware during the USB enumeration process (i.e., SetAddress) to the non-zero address assigned by the USB host.
Note
2. For PS/2 operation, the D+/D– Forcing Bit [2:0] = 111b mode must be set initially (one time only) before using the other PS/2 force modes
Document #: 38-08022 Rev. *E
Page 18 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Bit 7: STALL
Bit 5: OUT Received
1 = A valid OUT packet has been received. This bit is updated
to ‘1’ after the last received packet in an OUT transaction. This
bit is cleared by any non-locked writes to the register.
1 = The SIE will stall an OUT packet if the Mode Bits are set
to ACK-OUT, and the SIE will stall an IN packet if the mode
bits are set to ACK-IN. See Section for the available modes.
0 = No OUT received. This bit is cleared by any non-locked
writes to the register.
0 = This bit must be set to LOW for all other modes.
Bit 4: ACKed Transaction
The ACKed Transaction bit is set whenever the SIE engages
in a transaction to the register's endpoint that completes with
an ACK packet.
1 = The transaction completes with an ACK.
Bit [6:5]: Reserved. Must be written to zero during register writes.
Bit 4: ACKed Transaction
The ACKed transaction bit is set whenever the SIE engages
in a transaction to the register's endpoint that completes with
an ACK packet.
1 = The transaction completes with an ACK.
0 = The transaction does not complete with an ACK.
0 = The transaction does not complete with an ACK.
Bit [3:0]: Mode Bit[3:0]
The endpoint modes determine how the SIE responds to USB
traffic that the host sends to the endpoint. For example, if the
endpoint Mode Bits [3:0] are set to 0001 which is NAK IN/OUT
mode as shown in Table 8, the SIE will send NAK handshakes
in response to any IN or OUT token sent to this endpoint. In
this NAK IN/OUT mode, the SIE will send an ACK handshake
when the host sends a SETUP token to this endpoint. The
mode encoding is shown in Table 8. Additional information on
the mode bits can be found in Table 9 and Table 10. These
modes give the firmware total control on how to respond to
different tokens sent to the endpoints from the host.
In addition, the Mode Bits are automatically changed by the
SIE in response to many USB transactions. For example, if
the Mode Bit [3:0] are set to 1011 which is ACK OUT-NAK IN
mode as shown in Table 8, the SIE will change the endpoint
Mode Bit [3:0] to NAK IN/OUT (0001) mode after issuing an
ACK handshake in response to an OUT token. Firmware
needs to update the mode for the SIE to respond appropriately.
USB Non-control Endpoints
The CY7C637xxC feature two non-control endpoints, endpoint 1
(EP1) and endpoint 2 (EP2). The EP1 and EP2 Mode Registers
do not have the locking mechanism of the EP0 Mode Register.
The EP1 and EP2 Mode Registers use the format shown in
Figure . EP1 uses an 8-byte FIFO at SRAM locations
0xF0–0xF7, EP2 uses an 8-byte FIFO at SRAM locations
0xE8–0xEF as shown in Section .
Figure 17. USB Endpoint EP1, EP2 Mode Registers (Addresses 0x14 and 0x16)
Bit [3:0]: Mode Bit [3:0]
The EP1 and EP2 Mode Bits operate in the same manner as
the EP0 Mode Bits (see Section ).
USB Endpoint Counter Registers
There are three Endpoint Counter registers, with identical
formats for both control and non-control endpoints. These
registers contain byte count information for USB transactions, as
well as bits for data packet status. The format of these registers
is shown in Figure 18.
Figure 18. Endpoint 0,1,2 Counter Registers
(Addresses 0x11, 0x13 and 0x15)
Bit #
7
6
Bit Name
Data
Toggle
Data
Valid
5
4
3
Read/Writ
e
R/W
R/W
-
-
R/
W
R/
W
R/
W
R/
W
Reset
0
0
0
0
0
0
0
0
Reserved
2
1
0
Byte Count
Bit 7: Data Toggle
This bit selects the DATA packet's toggle state. For IN transactions, firmware must set this bit to the select the transmitted
Data Toggle. For OUT or SETUP transactions, the hardware
sets this bit to the state of the received Data Toggle bit.
1 = DATA1
Bit #
7
6
5
4
3
Bit STALL Reserved ACKed
Name
Transaction
Read/
Write
R/W
-
-
R/C
Reset
0
0
0
0
2
1
0
Bit 6: Data Valid
Mode Bit
R/W R/W R/W R/W
0
0
0
0 = DATA0
0
This bit is used for OUT and SETUP tokens only. This bit is
cleared to ‘0’ if CRC, bitstuff, or PID errors have occurred.
This bit does not update for some endpoint mode settings.
Refer to Table 10 for more details.
1 = Data is valid.
0 = Data is invalid. If enabled, the endpoint interrupt will occur
even if invalid data is received.
Document #: 38-08022 Rev. *E
Page 19 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Bit [5:4]: Reserved
Bit [3:0]: Byte Count Bit [3:0]
Byte Count Bits indicate the number of data bytes in a transaction: For IN transactions, firmware loads the count with the
number of bytes to be transmitted to the host from the endpoint FIFO. Valid values are 0 to 8 inclusive. For OUT or SETUP transactions, the count is updated by hardware to the
number of data bytes received, plus 2 for the CRC bytes. Valid
values are 2 to 10 inclusive.
For Endpoint 0 Count Register, whenever the count updates
from a SETUP or OUT transaction, the count register locks
and cannot be written by the CPU. Reading the register unlocks it. This prevents firmware from overwriting a status update on incoming SETUP or OUT transactions before firmware has a chance to read the data.
USB Regulator Output
The VREG pin provides a regulated output for connecting the
pull-up resistor required for USB operation. For USB, a 1.5-k
resistor is connected between the D– pin and the VREG voltage,
to indicate low-speed USB operation. Since the VREG output
has an internal series resistance of approximately 200, the
external pull-up resistor required is RPU (see Section ).
The regulator output is placed in a high-impedance state at reset,
and must be enabled by firmware by setting the VREG Enable
bit in the USB Status and Control Register (Figure 14). This
simplifies the design of a combination PS/2-USB device, since
the USB pull-up resistor can be left in place during PS/2
operation without loading the PS/2 line. In this mode, the VREG
pin can be used as an input and its state can be read at port P2.0.
Refer to Figure for the Port 2 data register. This input has a TTL
threshold.
In suspend mode, the regulator is automatically disabled. If
VREG Enable bit is set (Figure 14), the VREG pin is pulled up to
VCC with an internal 6.2-k resistor. This holds the proper VOH
state in suspend mode
Note that enabling the device for USB (by setting the Device
Address Enable bit, Figure 15) activates the internal regulator,
Document #: 38-08022 Rev. *E
even if the VREG Enable bit is cleared to 0. This insures proper
USB signaling in the case where the VREG pin is used as an
input, and an external regulator is provided for the USB pull-up
resistor. This also limits the swing on the D– and D+ pins to about
1V above the internal regulator voltage, so the Device Address
Enable bit normally should only be set for USB operating modes.
The regulator output is only designed to provide current for the
USB pull-up resistor. In addition, the output voltage at the VREG
pin is effectively disconnected when the CY7C637xxC device
transmits USB from the internal SIE. This means that the VREG
pin does not provide a stable voltage during transmits, although
this does not affect USB signaling.
PS/2 Operation
The CY7C637xxC parts are optimized for combination USB or
PS/2 devices, through the following features:
1. USB D+ and D– lines can also be used for PS/2 SCLK and
SDATA pins, respectively. With USB disabled, these lines can
be placed in a high-impedance state that will pull up to VCC.
(Disable USB by clearing the Address Enable bit of the USB
Device Address Register, Figure 15).
2. An interrupt is provided to indicate a long LOW state on the
SDATA pin. This eliminates the need to poll this pin to check
for PS/2 activity. Refer to Section for more details.
3. Internal PS/2 pull-up resistors can be enabled on the SCLK
and SDATA lines, so no GPIO pins are required for this task
(bit 7, USB Status and Control Register, Figure 14).
4. The controlled slew rate outputs from these pins apply to both
USB and PS/2 modes to minimize EMI.
5. The state of the SCLK and SDATA pins can be read, and can
be individually driven LOW in an open drain mode. The pins
are read at bits [5:4] of Port 2, and are driven with the Control
Bits [2:0] of the USB Status and Control Register.
6. The VREG pin can be placed into a high-impedance state, so
that a USB pull-up resistor on the D–/SDATA pin will not
interfere with PS/2 operation (bit 6, USB Status and Control
Register).
The PS/2 on-chip support circuitry is illustrated in Figure 19.
Page 20 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 19. Diagram of USB-PS/2 System Connections
Port 2.0
VREG Enable
200
3.3V
Regulator
VREG
VCC
PS/2 Pull-up
Enable
1.3 k
5 k
5 k
D+/SCLK
USB - PS/2
Driver
D–/SDATA
Port 2.5
Port 2.4
Document #: 38-08022 Rev. *E
On-chip
Off-chip
Page 21 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Serial Peripheral Interface (SPI)
SPI is a four-wire, full-duplex serial communication interface
between a master device and one or more slave devices. The
CY7C637xxC SPI circuit supports byte serial transfers in either
Master or Slave modes. The block diagram of the SPI circuit is
shown in Figure 20. The block contains buffers for both transmit
and receive data for maximum flexibility and throughput. The
CY7C637xxC can be configured as either an SPI Master or
Slave. The external interface consists of Master-Out/Slave-In
(MOSI), Master-In/Slave-Out (MISO), Serial Clock (SCK), and
Slave Select (SS).
SPI modes are activated by setting the appropriate bits in the SPI
Control Register, as described below.
Figure 20. SPI Block Diagram
Data Bus
Write
TX Buffer
8 bit shift register
Master
/ Slave
Control
MOSI
MISO
SCK
RX Buffer
SS
4
Internal SCK
Data Bus
Read
The SPI Data Register below serves as a transmit and receive
buffer.
Bit #
7
6
5
Bit Name
4
3
2
1
0
Data I/O
Read/Write R/W R/W R/W R/W R/W R/W R/W R/W
Reset
0
0
0
0
0
0
0
0
Figure 21. SPI Data Register (Address 0x60)
Bit [7:0]: Data I/O[7:0]
Writes to the SPI Data Register load the transmit buffer, while
reads from this register read the receive buffer contents.
1 = Logic HIGH
0 = Logic LOW
Operation as an SPI Master
Only an SPI Master can initiate a byte/data transfer. This is done
by the Master writing to the SPI Data Register. The Master shifts
out 8 bits of data (MSB first) along with the serial clock SCK for
the Slave. The Master’s outgoing byte is replaced with an
incoming one from a Slave device. When the last bit is received,
the shift register contents are transferred to the receive buffer
and an interrupt is generated. The receive data must be read
Document #: 38-08022 Rev. *E
from the SPI Data Register before the next byte of data is transferred to the receive buffer, or the data will be lost.
When operating as a Master, an active LOW Slave Select (SS)
must be generated to enable a Slave for a byte transfer. This
Slave Select is generated under firmware control, and is not part
of the SPI internal hardware. Any available GPIO can be used
for the Master’s Slave Select output.
When the Master writes to the SPI Data Register, the data is
loaded into the transmit buffer. If the shift register is not busy
shifting a previous byte, the TX buffer contents will be automatically transferred into the shift register and shifting will begin. If
the shift register is busy, the new byte will be loaded into the shift
register only after the active byte has finished and is transferred
to the receive buffer. The new byte will then be shifted out. The
Transmit Buffer Full (TBF) bit will be set HIGH until the transmit
buffer’s data-byte is transferred to the shift register. Writing to the
transmit buffer while the TBF bit is HIGH will overwrite the old
byte in the transmit buffer.
The byte shifting and SCK generation are handled by the
hardware (based on firmware selection of the clock source).
Data is shifted out on the MOSI pin (P0.5) and the serial clock is
output on the SCK pin (P0.7). Data is received from the slave on
the MISO pin (P0.6). The output pins must be set to the desired
drive strength, and the GPIO data register must be set to 1 to
enable a bypass mode for these pins. The MISO pin must be
configured in the desired GPIO input mode. See Section for
GPIO configuration details.
Page 22 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Master SCK Selection
SPI Status and Control
The Master’s SCK is programmable to one of four clock settings,
as shown in Figure 20. The frequency is selected with the Clock
Select Bits of the SPI control register. The hardware provides 8
output clocks on the SCK pin (P0.7) for each byte transfer. Clock
phase and polarity are selected by the CPHA and CPOL control
bits (see Figure 20 and 23).
The SPI Control Register is shown in Figure 22. The timing
diagram in Figure 23 shows the clock and data states for the
various SPI modes.
The master SCK duty cycle is nominally 33% in the fastest (2
Mbps) mode, and 50% in all other modes.
Operation as an SPI Slave
In slave mode, the chip receives SCK from an external master
on pin P0.7. Data from the master is shifted in on the MOSI pin
(P0.5), while data is being shifted out of the slave on the MISO
pin (P0.6). In addition, the active LOW Slave Select must be
asserted to enable the slave for transmit. The Slave Select pin is
P0.4. These pins must be configured in appropriate GPIO
modes, with the GPIO data register set to 1 to enable bypass
mode selected for the MISO pin.
In Slave mode, writes to the SPI Data Register load the Transmit
buffer. If the Slave Select is asserted (SS LOW) and the shift
register is not busy shifting a previous byte, the transmit buffer
contents will be automatically transferred into the shift register. If
the shift register is busy, the new byte will be loaded into the shift
register only after the active byte has finished and is transferred
to the receive buffer. The new byte is then ready to be shifted out
(shifting waits for SCK from the Master). If the Slave Select is not
active when the transmit buffer is loaded, data is not transferred
to the shift register until Slave Select is asserted. The Transmit
Buffer Full (TBF) bit will be set to ‘1’ until the transmit buffer’s
data-byte is transferred to the shift register. Writing to the
transmit buffer while the TBF bit is HIGH will overwrite the old
byte in the Transmit Buffer.
If the Slave Select is deasserted before a byte transfer is
complete, the transfer is aborted and no interrupt is generated.
Whenever Slave Select is asserted, the transmit buffer is
automatically reloaded into the shift register.
Clock phase and polarity must be selected to match the SPI
master, using the CPHA and CPOL control bits (see Figure 22
and Figure 23).
The SPI slave logic continues to operate in suspend, so if the SPI
interrupt is enabled, the device can go into suspend during a SPI
slave transaction, and it will wake up at the interrupt that signals
the end of the byte transfer.
Figure 22. SPI Control Register (Address 0x61)
Bit #
7
6
Bit Name TCMP TBF
5
4
3
0
1
0
Comm CPOL CPHA SCK
Mode[1:0]
Select
Read/Write R/W R/W R/W R/W R/W
Reset
2
0
0
0
0
R/W R/W R/W
0
0
0
Bit 7: TCMP
1 = TCMP is set to 1 by the hardware when 8-bit transfer is
complete. The SPI interrupt is asserted at the same time
TCMP is set to 1.
0 = This bit is only cleared by firmware.
Bit 6: TBF
Transmit Buffer Full bit.
1 = Indicates data in the transmit buffer has not transferred to
the shift register.
0 = Indicates data in the transmit buffer has transferred to the
shift register.
Bit [5:4] Comm Mode[1:0]
00 = All communications functions disabled (default).
01 = SPI Master Mode.
10 = SPI Slave Mode.
11 = Reserved.
Bit 3: CPOL
SPI Clock Polarity bit.
1 = SCK idles HIGH.
0 = SCK idles LOW.
Bit 2: CPHA
SPI Clock Phase bit (see Figure 23)
Bit [1:0]: SCK Select
Master mode SCK frequency selection (no effect in Slave
Mode):
00 = 2 Mbit/s
01 = 1 Mbit/s
10 = 0.5 Mbit/s
11 = 0.0625 Mbit/s
Document #: 38-08022 Rev. *E
Page 23 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 23. SPI Data Timing
SCK (CPOL = 0)
SCK (CPOL = 1)
SS
CPHA = 0:
MOSI/MISO
x
MSB
LSB
Data Capture Strobe
Interrupt Issued
CPHA = 1:
MOSI/MISO
MSB
LSB
x
Data Capture Strobe
Interrupt Issued
SPI Interrupt
For SPI, an interrupt request is generated after a byte is received
or transmitted. See Section for details on the SPI interrupt.
SPI Modes for GPIO Pins
The GPIO pins used for SPI outputs (P0.5–P0.7) contain a
bypass mode, as shown in the GPIO block diagram (Figure ).
Whenever the SPI block is inactive (Mode[5:4] = 00), the bypass
value is 1, which enables normal GPIO operation. When SPI
master or slave modes are activated, the appropriate bypass
signals are driven by the hardware for outputs, and are held at 1
for inputs. Note that the corresponding data bits in the Port 0
Data Register must be set to 1 for each pin being used for
an SPI output. In addition, the GPIO modes are not affected by
operation of the SPI block, so each pin must be programmed by
firmware to the desired drive strength mode.
For GPIO pins that are not used for SPI outputs, the SPI bypass
value in Figure is always 1, for normal GPIO operation.
Table 5. SPI Pin Assignments
SPI Function
GPIO Pin
Slave Select (SS)
P0.4
For master mode, firmware sets SS, may use any GPIO pin.
For Slave Mode, SS is an active LOW input.
Master Out, Slave In (MOSI)
P0.5
Data output for master, data input for slave.
Master In, Slave Out (MISO)
P0.6
Data input for master, data output for slave.
SCK
P0.7
SPI Clock: Output for master, input for slave.
Document #: 38-08022 Rev. *E
Comment
Page 24 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
12-bit Free-running Timer
Bit [7:0]: Timer lower eight bits
The 12-bit timer operates with a 1-s tick, provides two interrupts
(128-s and 1.024-ms) and allows the firmware to directly time
events that are up to 4 ms in duration. The lower eight bits of the
timer can be read directly by the firmware. Reading the lower
eight bits latches the upper four bits into a temporary register.
When the firmware reads the upper four bits of the timer, it is
actually reading the count stored in the temporary register. The
effect of this is to ensure a stable 12-bit timer value can be read,
even when the two reads are separated in time.
Figure 25. Timer MSB Register (Address 0x25)
Bit #
7
6
Bit Name
5
4
3
Reserved
2
1
0
Timer [11:8]
Read/Write
-
-
-
-
R
R
R
R
Reset
0
0
0
0
0
0
0
0
Figure 24. Timer LSB Register (Address 0x24)
Bit [7:4]: Reserved
Bit #
7
6
5
Bit Name
4
3
2
1
0
Bit [3:0]: Timer upper four bits
Timer [7:0]
Read/Write
R
R
R
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
Figure 26. Timer Block Diagram
1.024-ms interrupt
128-s interrupt
11
10
9
8
L3
L2
L1
L0
D3
D2
D1
7
D0
6
D7
4
5
D6
D5
3
D4
2
D3
1
D2
0
D1
1 MHz clock
D0
To Timer Registers
8
Document #: 38-08022 Rev. *E
Page 25 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Timer Capture Registers
Four 8-bit capture timer registers provide both rising- and falling-edge event timing capture on two pins. Capture Timer A is connected
to Pin 0.0, and Capture Timer B is connected to Pin 0.1. These can be used to mark the time at which a rising or falling event occurs
at the two GPIO pins. Each timer will capture eight bits of the free-running timer into its Capture Timer Data Register if a rising or
falling edge event that matches the specified rising or falling edge condition at the pin. A prescaler allows selection of the capture
timer tick size. Interrupts can be individually enabled for the four capture registers. A block diagram is shown in Figure .
Figure 27. Capture Timers Block Diagram
Free-running Timer
11
10
First Edge Hold
Bit 7, Reg 0x44
GPIO
P0.0
GPIO
P0.1
9
8
7
6
5
4
3
2
1
0
1 MHz
Clock
Prescaler
Mux
8-bit Capture Registers
Rising
Edge
Detect
Timer A Rising Edge Time
Falling
Edge
Detect
Timer A Falling Edge Time
Rising
Edge
Detect
Timer B Rising Edge Time
Falling
Edge
Detect
Timer B Falling Edge Time
Capture A Rising Int Enable
Bit 0, Reg 0x44
Capture Timer A Interrupt Request
Capture A Falling Int Enable
Bit 1, Reg 0x44
Capture B Rising Int Enable
Bit 2, Reg 0x44
Capture Timer B Interrupt Request
Capture B Falling Int Enable
Bit 3, Reg 0x44
Document #: 38-08022 Rev. *E
Page 26 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
The four Capture Timer Data Registers are read-only, and are
shown in Figure through Figure 30.
Out of the 12-bit free running timer, the 8-bit captured in the
Capture Timer Data Registers are determined by the Prescale
Bit [2:0] in the Capture Timer Configuration Register (Figure 32).
Capture Timer A-Rising, Data Register (Address 0x40.)
Bit #
7
6
Bit Name
5
4
3
2
1
0
Figure 31. Capture Timer Status Register (Address 0x45)
Bit #
7
Bit
Name
6
5
4
Reserved
R
R
R
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
2
1
0
Capture Capture Capture Capture
B
B
A
A
Falling Rising Falling Rising
Event
Event
Event
Event
Capture A Rising Data
Read/Write
3
Read/
Write
-
-
-
-
R
R
R
R
Reset
0
0
0
0
0
0
0
0
Figure 28. Capture Timer A-Falling, Data Register
(Address 0x41)
Bit [7:4]: Reserved.
Bit #
7
6
Bit Name
5
4
3
2
1
0
Capture A Falling Data
Read/Write
R
R
R
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
Bit #
7
6
5
4
3
2
1
0
Capture B Rising Data
R
R
R
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
Figure 30. Capture Timer B-Falling, Data Register
(Address 0x43)
7
6
Bit Name
5
4
3
2
1
0
Capture B Falling Data
Figure 32. Capture Timer Configuration Register
(Address 0x44)
Bit #
R
R
R
R
R
R
R
R
Reset
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
Bit First Prescale Bit Capture Capture Capture Capture
Name Edge
[2:0]
B
B
A
A
Hold
Falling Rising Falling Rising
Int
Int
Int
Int
Enable Enable Enable Enable
Read/ R/W R/W R/W R/W
Write
Reset
Read/Write
Document #: 38-08022 Rev. *E
1 = A rising or falling event that matches the pin’s rising/falling
condition has occurred.
Because both Capture A events (rising and falling) share an
interrupt, user’s firmware needs to check the status of both
Capture A Falling and Rising Event bits to determine what
caused the interrupt. This is also true for Capture B events.
Read/Write
Bit #
These bits record the occurrence of any rising or falling edges
on the capture GPIO pins. Bits in this register are cleared by
reading the corresponding data register.
0 = No event that matches the pin’s rising or falling edge condition.
Figure 29. Capture Timer B-Rising, Data Register
(Address 0x42)
Bit Name
Bit [3:0]: Capture A/B, Falling/Rising Event
0
0
0
0
R/W
R/W
R/W
R/W
0
0
0
0
Page 27 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Bit 7: First Edge Hold
1 = The time of the first occurrence of an edge is held in the
Capture Timer Data Register until the data is read. Subsequent edges are ignored until the Capture Timer Data Register is read.
0 = The time of the most recent edge is held in the Capture
Timer Data Register. That is, if multiple edges have occurred
before reading the capture timer, the time for the last one will
be read (default state).
The First Edge Hold function applies globally to all four capture timers.
Bit [6:4]: Prescale Bit [2:0]
Three prescaler bits allow the capture timer clock rate to be
selected among 5 choices, as shown in Table 6 below.
Bit [3:0]: Capture A/B, Rising/Falling Interrupt Enable
Each of the four Capture Timer registers can be individually
enabled to provide interrupts.
Document #: 38-08022 Rev. *E
Both Capture A events share a common interrupt request, as
do the two Capture B events. In addition to the event enables,
the main Capture Interrupt Enables bit in the Global Interrupt
Enable register (Section ) must be set to activate a capture
interrupt.
1 = Enable interrupt
0 = Disable interrupt
Table 6. Capture Timer Prescalar Settings (Step size and
range for FCLK = 6 MHz)
Prescale
2:0
Captured Bits
LSB
Step
Size
Range
000
Bits 7:0 of free-running timer
1s
256 s
001
Bits 8:1 of free-running timer
2s
512 s
010
Bits 9:2 of free-running timer
4s
1.024 ms
011
Bits 10:3 of free-running timer
8s
2.048 ms
100
Bits 11:4 of free-running timer
16s
4.096 ms
Page 28 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Processor Status and Control Register
Figure 33. Processor Status and Control Register (Address 0xFF)
Bit #
7
6
5
4
3
2
1
0
Bit Name
IRQ
Pending
Watchdog
Reset
Bus
Interrupt
Event
LVR/BOR
Reset
Suspend
Interrupt
Enable
Sense
Reserved
Run
Read/Write
R
R/W
R/W
R/W
R/W
R
-
R/W
Reset
0
1
0
1
0
0
0
1
Bit 7: IRQ Pending
When an interrupt is generated, it is registered as a pending
interrupt. The interrupt will remain pending until its interrupt
enable bit is set (Figure and Figure ) and interrupts are globally enabled (Bit 2, Processor Status and Control Register).
At that point the internal interrupt handling sequence will clear
the IRQ Pending bit until another interrupt is detected as
pending. This bit is only valid if the Global Interrupt Enable bit
is disabled.
1 = There are pending interrupts.
0 = No pending interrupts.
Bit 6: Watchdog Reset
The Watchdog Timer Reset (WDR) occurs when the internal
Watchdog timer rolls over. The timer will roll over and WDR
will occur if it is not cleared within tWATCH (see Section for the
value of tWATCH). This bit is cleared by an LVR/BOR. Note that
a Watchdog reset can occur with a POR/LVR/BOR event, as
discussed at the end of this section.
1 = A Watchdog reset occurs.
0 = No Watchdog reset
Bit 5: Bus Interrupt Event
The Bus Reset Status is set whenever the event for the USB
Bus Reset or PS/2 Activity interrupt occurs. The event type
(USB or PS/2) is selected by the state of the USB-PS/2 Interrupt Mode bit in the USB Status and Control Register (see
Figure 14). The details on the event conditions that set this bit
are given in Section . In either mode, this bit is set as soon as
the event has lasted for 128–256 s, and the bit will be set
even if the interrupt is not enabled. The bit is only cleared by
firmware or LVR/WDR.
1 = A USB reset occurred or PS/2 Activity is detected, depending on USB-PS/2 Interrupt Select bit.
0 = No event detected since last cleared by firmware or
LVR/WDR.
Bit 4: LVR/BOR Reset
The Low-voltage or Brown-out Reset is set to ‘1’ during a
power-on reset. Firmware can check bits 4 and 6 in the reset
handler to determine whether a reset was caused by a
LVR/BOR condition or a Watchdog timeout. This bit is not
Document #: 38-08022 Rev. *E
affected by WDR. Note that a LVR/BOR event may be followed by a Watchdog reset before firmware begins executing,
as explained at the end of this section.
1 = A POR or LVR has occurred.
0 = No POR nor LVR since this bit last cleared.
Bit 3: Suspend
Writing a '1' to the Suspend bit will halt the processor and
cause the microcontroller to enter the suspend mode that significantly reduces power consumption. An interrupt or USB
bus activity will cause the device to come out of suspend.
After coming out of suspend, the device will resume firmware
execution at the instruction following the IOWR which put the
part into suspend. When writing the suspend bit with a resume
condition present (such as non-idle USB activity), the suspend state will still be entered, followed immediately by the
wake-up process (with appropriate delays for the clock
start-up). See Section for more details on suspend mode
operation.
1 = Suspend the processor.
0 = Not in suspend mode. Cleared by the hardware when
resuming from suspend.
Bit 2: Interrupt Enable Sense
This bit shows whether interrupts are enabled or disabled.
Firmware has no direct control over this bit as writing a zero
or one to this bit position will have no effect on interrupts. This
bit is further gated with the bit settings of the Global Interrupt
Enable Register (Figure ) and USB Endpoint Interrupt Enable
Register (Figure ). Instructions DI, EI, and RETI manipulate
the state of this bit.
1 = Interrupts are enabled.
0 = Interrupts are masked off.
Bit 1: Reserved. Must be written as a 0.
Bit 0: Run
This bit is manipulated by the HALT instruction. When Halt is
executed, the processor clears the run bit and halts at the end
of the current instruction. The processor remains halted until
a reset occurs (low-voltage, brown-out, or Watchdog). This bit
should normally be written as a ‘1’.
Page 29 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
During power-up, or during a low-voltage reset, the Processor
Status and Control Register is set to 00010001, which indicates
a LVR/BOR (bit 4 set) has occurred and no interrupts are pending
(bit 7 clear). Note that during the tSTART ms partial suspend at
start-up (explained in Section ), a Watchdog Reset will also
occur. When a WDR occurs during the power-up suspend
interval, firmware would read 01010001 from the Status and
Control Register after power-up. Normally the LVR/BOR bit
should be cleared so that a subsequent WDR can be clearly
identified. Note that if a USB bus reset (long SE0) is received
before firmware examines this register, the Bus Interrupt Event
bit would also be set.
During a Watchdog Reset, the Processor Status and Control
Register is set to 01XX0001, which indicates a Watchdog Reset
(bit 4 set) has occurred and no interrupts are pending (bit 7
clear).
Interrupts
Interrupts can be generated by the GPIO lines, the internal
free-running timer, the SPI block, the capture timers, on various
USB events, PS/2 activity, or by the wake-up timer. All interrupts
are maskable by the Global Interrupt Enable Register and the
USB End Point Interrupt Enable Register. Writing a ‘1’ to a bit
position enables the interrupt associated with that bit position.
During a reset, the contents of the interrupt enable registers are
cleared, along with the Global Interrupt enable bit of the CPU,
effectively disabling all interrupts.
The interrupt controller contains a separate flip-flop for each
interrupt. See Figure 36 for the logic block diagram of the
interrupt controller. When an interrupt is generated it is first registered as a pending interrupt. It will stay pending until it is serviced
or a reset occurs. A pending interrupt will only generate an
interrupt request if it is enabled by the corresponding bit in the
interrupt enable registers. The highest priority interrupt request
will be serviced following the completion of the currently
executing instruction.
When servicing an interrupt, the hardware will first disable all
interrupts by clearing the Global Interrupt Enable bit in the CPU
(the state of this bit can be read at Bit 2 of the Processor Status
and Control Register). Next, the flip-flop of the current interrupt
is cleared. This is followed by an automatic CALL instruction to
the ROM address associated with the interrupt being serviced
(i.e., the Interrupt Vector, see Section ). The instruction in the
interrupt table is typically a JMP instruction to the address of the
Interrupt Service Routine (ISR). The user can re-enable interrupts in the interrupt service routine by executing an EI
instruction. Interrupts can be nested to a level limited only by the
available stack space.
The Program Counter value as well as the Carry and Zero flags
(CF, ZF) are stored onto the Program Stack by the automatic
CALL instruction generated as part of the interrupt acknowledge
process. The user firmware is responsible for ensuring that the
processor state is preserved and restored during an interrupt.
The PUSH A instruction should typically be used as the first
command in the ISR to save the accumulator value and the POP
A instruction should be used just before the RETI instruction to
restore the accumulator value. The program counter, CF and ZF
Document #: 38-08022 Rev. *E
are restored and interrupts are enabled when the RETI
instruction is executed.
The DI and EI instructions can be used to disable and enable
interrupts, respectively. These instructions affect only the Global
Interrupt Enable bit of the CPU. If desired, EI can be used to
re-enable interrupts while inside an ISR, instead of waiting for the
RETI that exits the ISR. While the global interrupt enable bit is
cleared, the presence of a pending interrupt can be detected by
examining the IRQ Sense bit (Bit 7 in the Processor Status and
Control Register).
Interrupt Vectors
The Interrupt Vectors supported by the device are listed in
Table 7. The highest priority interrupt is #1 (USB Bus Reset /
PS/2 activity), and the lowest priority interrupt is #11 (Wake-up
Timer). Although Reset is not an interrupt, the first instruction
executed after a reset is at ROM address 0x0000, which corresponds to the first entry in the Interrupt Vector Table. Interrupt
vectors occupy two bytes to allow for a two-byte JMP instruction
to the appropriate Interrupt Service Routine (ISR).
Table 7. Interrupt Vector Assignments
Interrupt
Vector No.
ROM
Address
not applicable
0x0000
Execution after Reset begins
here
1
0x0002
USB Bus Reset or PS/2 Activity
interrupt
2
0x0004
128-s timer interrupt
3
0x0006
1.024-ms timer interrupt
4
0x0008
USB Endpoint 0 interrupt
Function
5
0x000A
USB Endpoint 1 interrupt
6
0x000C
USB Endpoint 2 interrupt
7
0x000E
SPI Interrupt
8
0x0010
Capture Timer A interrupt
9
0x0012
Capture Timer B interrupt
10
0x0014
GPIO interrupt
11
0x0016
Wake-up Timer interrupt
Interrupt Latency
Interrupt latency can be calculated from the following equation:
Interrupt Latency = (Number of clock cycles remaining in the
current instruction)
+ (10 clock cycles for the CALL instruction)
+ (5 clock cycles for the JMP instruction)
For example, if a 5 clock cycle instruction such as JC is being
executed when an interrupt occurs, the first instruction of the
Interrupt Service Routine will execute a minimum of 16 clocks
(1+10+5) or a maximum of 20 clocks (5+10+5) after the interrupt
is issued. With a 6-MHz external resonator, internal CPU clock
speed is 12 MHz, so 20 clocks take 20/12 MHz = 1.67 s.
Page 30 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Interrupt Sources
The following sections provide details on the different types of interrupt sources.
Figure 34. Global Interrupt Enable Register (Address 0x20)
Bit #
7
6
5
4
3
2
1
0
Bit Name
Wake-up
Interrupt
Enable
GPIO
Interrupt
Enable
Capture
Timer B
Intr. Enable
Capture
Timer A
Intr. Enable
SPI
Interrupt
Enable
1.024-ms
Interrupt
Enable
128-s
Interrupt
Enable
USB Bus
Reset /
PS/2 Activity
Intr. Enable
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
Bit 7: Wake-up Interrupt Enable
The internal wake-up timer is normally used to wake the part
from suspend mode, but it can also provide an interrupt when
the part is awake. The wake-up timer is cleared whenever the
Wake-up Interrupt Enable bit is written to a 0, and runs whenever that bit is written to a 1. When the interrupt is enabled,
the wake-up timer provides periodic interrupts at multiples of
period, as described in Section .
1 = Enable wake-up timer for periodic wake-up.
0 = Disable and power-off wake-up timer.
Bit 6: GPIO Interrupt Enable
Each GPIO pin can serve as an interrupt input. During a reset,
GPIO interrupts are disabled by clearing all GPIO interrupt
enable registers. Writing a ‘1’ to a GPIO Interrupt Enable bit
enables GPIO interrupts from the corresponding input pin.
These registers are shown in Figure 37 for Port 0 and
Figure 38 for Port 1. In addition to enabling the desired individual pins for interrupt, the main GPIO interrupt must be enabled, as explained in Section .
The polarity that triggers an interrupt is controlled independently for each GPIO pin by the GPIO Interrupt Polarity Registers. Setting a Polarity bit to ‘0’ allows an interrupt on a falling
GPIO edge, while setting a Polarity bit to ‘1’ allows an interrupt
on a rising GPIO edge. The Polarity Registers reset to 0 and
are shown in Figure 39 for Port 0 and Figure for Port 1.
All of the GPIO pins share a single interrupt vector, which
means the firmware will need to read the GPIO ports with
enabled interrupts to determine which pin or pins caused an
interrupt.The GPIO interrupt structure is illustrated in Figure .
Note that if one port pin triggered an interrupt, no other port
pins can cause a GPIO interrupt until that port pin has returned to its inactive (non-trigger) state or its corresponding
port interrupt enable bit is cleared. The CY7C637xxC does
not assign interrupt priority to different port pins and the Port
Interrupt Enable Registers are not affected by the interrupt
acknowledge process.
Bit [5:4]: Capture Timer A and B Interrupts
There are two capture timer interrupts, one for each associated
pin. Each of these interrupts occurs on an enabled edge of the
selected GPIO pin(s). For each pin, rising and/or falling edge
capture interrupts can be in selected. Refer to Section . These
interrupts are independent of the GPIO interrupt, described in the
next section.
1 = Enable
0 = Disable
Bit 3: SPI Interrupt Enable
The SPI interrupt occurs at the end of each SPI byte transaction,
at the final clock edge, as shown in Figure 23. After the interrupt,
the received data byte can be read from the SPI Data Register,
and the TCMP control bit will be high
1 = Enable
0 = Disable
Bit 2: 1.024-ms Interrupt Enable
The 1.024-ms interrupts are periodic timer interrupts from the
free-running timer (based on the 6-MHz clock). The user
should disable this interrupt before going into the suspend
mode to avoid possible conflicts between servicing the timer
interrupts (128-s interrupt and 1.024-ms interrupt) first or the
suspend request first when waking up.
1 = Enable. Periodic interrupts will be generated approximately every 1.024 ms.
0 = Disable.
Bit 1: 128-s Interrupt Enable
The 128-s interrupt is another source of timer interrupt from
the free-running timer. The user should disable both timer interrupts (128-s and 1.024-ms) before going into the suspend
mode to avoid possible conflicts between servicing the timer
interrupts first or the suspend request first when waking up.
1 = Enable
1 = Enable. Periodic interrupts will be generated approximately every 128 s.
0 = Disable
0 = Disable.
Document #: 38-08022 Rev. *E
Page 31 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Bit [2:1]: EP2,1 Interrupt Enable
Bit 0: USB Bus Reset - PS/2 Interrupt Enable
The function of this interrupt is selectable between detection
of either a USB bus reset condition, or PS/2 activity. The selection is made with the USB-PS/2 Interrupt Mode bit in the
USB Status and Control Register (Figure 14). In either case,
the interrupt will occur if the selected condition exists for 256
s, and may occur as early as 128 s.
A USB bus reset is indicated by a single ended zero (SE0) on
the USB D+ and D– pins. The USB Bus Reset interrupt occurs
when the SE0 condition ends. PS/2 activity is indicated by a
continuous LOW on the SDATA pin. The PS/2 interrupt occurs
as soon as the long LOW state is detected.
During the entire interval of a USB Bus Reset or PS/2 interrupt
event, the USB Device Address register is cleared.
The Bus Reset/PS/2 interrupt may occur 128 s after the bus
condition is removed.
There are two non-control endpoint (EP2 and EP1) interrupts.
If enabled, a non-control endpoint interrupt is generated
when:
❐ The USB host writes valid data to an endpoint FIFO. However, if the endpoint is in ACK OUT modes, an interrupt is generated regardless of data packet validity (i.e., good CRC).
Firmware must check for data validity.
❐ The device SIE sends a NAK or STALL handshake packet
to the USB host during the host attempts to read data from
the endpoint (INs).
❐ The device receives an ACK handshake after a successful
read transaction (IN) from the host.
❐ The device SIE sends a NAK or STALL handshake packet
to the USB host during the host attempts to write data (OUTs)
to the endpoint FIFO.
1 = Enable
0 = Disable
1 = Enable
Refer to Table 8 for more information.
0 = Disable
Figure 35. Endpoint Interrupt Enable Register
(Address 0x21)
Bit 0: EP0 Interrupt Enable
If enabled, a control endpoint interrupt is generated when:
The endpoint 0 mode is set to accept a SETUP token.
❐ After the SIE sends a 0-byte packet in the status stage of a
control transfer.
❐ The USB host writes valid data to an endpoint FIFO. However, if the endpoint is in ACK OUT modes, an interrupt is generated regardless of what data is received. Firmware must
check for data validity.
❐ The device SIE sends a NAK or STALL handshake packet
to the USB host during the host attempts to read data from
the endpoint (INs).
❐ The device SIE sends a NAK or STALL handshake packet
to the USB host during the host attempts to write data (OUTs)
to the endpoint FIFO.
1 = Enable EP0 interrupt
❐
Bit #
7 6 5 4 3
2
1
0
Bit Name
Reserved
EP2
Interrupt
Enable
EP1
Interrupt
Enable
EP0
Interrupt
Enable
R/W
R/W
R/W
0
0
0
Read/Write
Reset
-
-
-
-
-
0 0 0 0 0
Bit [7:3]: Reserved.
0 = Disable EP0 interrupt
Document #: 38-08022 Rev. *E
Page 32 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 36. Interrupt Controller Logic Block Diagram
USB-PS/2 Clear
Interrupt
Vector
CLR
1
Q
D
USBPS/2
Int
CLK
USB-PS/2 IRQ
128-s CLR
128-s IRQ
1-ms CLR
1-ms IRQ
Enable [0]
(Reg 0x20)
CPU
CLR
Q
D
EP2
Int
CLK
(Bit 7, Reg 0xFF)
IRQ
EP1 CLR
EP1 IRQ
EP2 CLR
EP2 IRQ
Enable [2]
(Reg 0x21)
IRQ Pending
IRQout
EP0 CLR
EP0 IRQ
1
To CPU
Global
Interrupt
Enable
Bit
SPI CLR
SPI IRQ
Capture A CLR
Capture A IRQ
(Bit 2, Reg 0xFF)
Controlled by DI, EI, and
RETI Instructions
CLR
Capture B CLR
Capture B IRQ
Int Enable
Sense
Interrupt
Acknowledge
GPIO CLR
GPIO IRQ
Wake-up CLR
CLR
1
D
Wake-up
Int
Bit #
Q
CLK
7
6
Bit Name
Wake-up IRQ
Enable [7]
(Reg 0x20)
Interrupt
Priority
Encoder
5
4
3
2
1
0
P0 Interrupt Enable
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Figure 37. Port 0 Interrupt Enable Register (Address 0x04)
Bit [7:0]: P0 [7:0] Interrupt Enable
Bit [7:0]: P1 [7:0] Interrupt Enable
1 = Enables GPIO interrupts from the corresponding input pin.
0 = Disables GPIO interrupts from the corresponding input
pin.
The polarity that triggers an interrupt is controlled independently
for each GPIO pin by the GPIO Interrupt Polarity Registers.
Figure 39 and Figure control the interrupt polarity of each GPIO
pin.
1 = Enables GPIO interrupts from the corresponding input pin.
0 = Disables GPIO interrupts from the corresponding input
pin.
Bit #
7
6
Bit Name
5
4
3
2
1
0
P1 Interrupt Enable
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Figure 38. Port 1 Interrupt Enable Register
(Address 0x05)
Document #: 38-08022 Rev. *E
Bit #
7
6
Bit Name
5
4
3
2
1
0
P0 Interrupt Polarity
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Figure 39. Port 0 Interrupt Polarity Register
(Address 0x06)
Bit [7:0]: P0[7:0] Interrupt Polarity
1 = Rising GPIO edge
0 = Falling GPIO edge
Page 33 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 40. Port 1 Interrupt Polarity Register
(Address 0x07)
Bit [7:0]: P1[7:0] Interrupt Polarity
1 = Rising GPIO edge
0 = Falling GPIO edge
Bit #
7
6
Bit Name
5
4
3
2
1
0
P1 Interrupt Polarity
Read/Write
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
0
Figure 41. GPIO Interrupt Diagram
Port Bit Interrupt
Polarity Register
M
U
X
GPIO
Pin
1 = Enable
0 = Disable
OR Gate
(1 input per
GPIO pin)
GPIO Interrupt
Flip Flop
1
D
Q
CLR
Interrupt
Priority
Encoder
IRQout
Interrupt
Vector
Port Bit Interrupt
Enable Register
IRA
1 = Enable
0 = Disable
Document #: 38-08022 Rev. *E
Global
GPIO Interrupt
Enable
(Bit 6, Register 0x20)
Page 34 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
USB Mode Tables
The following tables give details on mode setting for the USB Serial Interface Engine (SIE) for both the control endpoint (EP0) and
non-control endpoints (EP1 and EP2).
Table 8. USB Register Mode Encoding for Control and Non-Control Endpoints
Mode
Disable
NAK IN/OUT
Encoding
0000
0001
SETUP
Ignore
Accept
IN
Ignore
NAK
OUT
Ignore
NAK
Status OUT Only
STALL IN/OUT
Ignore IN/OUT
Reserved
Status IN Only
Reserved
NAK OUT
0010
0011
0100
0101
0110
0111
1000
Accept
Accept
Accept
Ignore
Accept
Ignore
Ignore
STALL
STALL
Ignore
Ignore
TX 0 Byte
TX Count
Ignore
Check
STALL
Ignore
Always
STALL
Ignore
NAK
ACK OUT(STALL[3]=0)
ACK OUT(STALL[3]=1)
NAK OUT - Status IN
ACK OUT - NAK IN
1001
1001
1010
1011
Ignore
Ignore
Accept
Accept
Ignore
Ignore
TX 0 Byte
NAK
ACK
STALL
NAK
ACK
NAK IN
ACK IN(STALL[3]=0)
ACK IN(STALL[3]=1)
NAK IN - Status OUT
ACK IN - Status OUT
1100
1101
1101
1110
1111
Ignore
Ignore
Ignore
Accept
Accept
NAK
TX Count
STALL
NAK
TX Count
Ignore
Ignore
Ignore
Check
Check
Comments
Ignore all USB traffic to this endpoint
On Control endpoint, after successfully sending an ACK
handshake to a SETUP packet, the SIE forces the
endpoint mode (from modes other than 0000) to 0001.
The mode is also changed by the SIE to 0001 from mode
1011 on issuance of ACK handshake to an OUT.
For Control endpoints
For Control endpoints
For Control endpoints
Reserved
For Control Endpoints
Reserved
In mode 1001, after sending an ACK handshake to an
OUT, the SIE changes the mode to 1000
This mode is changed by the SIE to mode 1000 on
issuance of ACK handshake to an OUT
This mode is changed by the SIE to mode 0001 on
issuance of ACK handshake to an OUT
An ACK from mode 1101 changes the mode to 1100
This mode is changed by the SIE to mode 1100 on
issuance of ACK handshake to an IN
An ACK from mode 1111 changes the mode to 1110
This mode is changed by the SIE to mode 1110 on
issuance of ACK handshake to an IN
Note
3. STALL bit is the bit 7 of the USB Non-Control Device Endpoint Mode registers. Refer to Section for more explanation.
Mode Column:
The 'Mode' column contains the mnemonic names given to the
modes of the endpoint. The mode of the endpoint is determined
by the four-bit binaries in the 'Encoding' column as discussed
below. The Status IN and Status OUT modes represent the
status IN or OUT stage of the control transfer.
Encoding Column:
The contents of the 'Encoding' column represent the Mode Bits
[3:0] of the Endpoint Mode Registers (Figure 16 and Figure ).
The endpoint modes determine how the SIE responds to
different tokens that the host sends to the endpoints. For
example, if the Mode Bits [3:0] of the Endpoint 0 Mode Register
(Figure 16) are set to '0001', which is NAK IN/OUT mode as
shown in Table 8 above, the SIE of the part will send an ACK
handshake in response to SETUP tokens and NAK any IN or
OUT tokens. For more information on the functionality of the
Serial Interface Engine (SIE), see Section .
A 'Check' in the Out column means that upon receiving an OUT
token the SIE checks to see whether the OUT is of zero length
and has a Data Toggle (Data1/0) of 1. If these conditions are true,
the SIE responds with an ACK. If any of the above conditions is
not met, the SIE will respond with either a STALL or Ignore.
Table 10 gives a detailed analysis of all possible cases.
A 'TX Count' entry in the IN column means that the SIE will
transmit the number of bytes specified in the Byte Count Bit [3:0]
of the Endpoint Count Register (Figure 18) in response to any IN
token.
A 'TX 0 Byte' entry in the IN column means that the SIE will
transmit a zero byte packet in response to any IN sent to the
endpoint. Sending a 0 byte packet is to complete the status stage
of a control transfer.
An 'Ignore' means that the device sends no handshake tokens.
An 'Accept' means that the SIE will respond with an ACK to a
valid SETUP transaction.
SETUP, IN, and OUT Columns:
Comments Column:
Depending on the mode specified in the 'Encoding' column, the
'SETUP', 'IN', and 'OUT' columns contain the device SIE's
responses when the endpoint receives SETUP, IN, and OUT
tokens respectively.
Some Mode Bits are automatically changed by the SIE in
response to many USB transactions. For example, if the Mode
Bits [3:0] are set to '1111' which is ACK IN-Status OUT mode as
shown in Table 8, the SIE will change the endpoint Mode Bits
Document #: 38-08022 Rev. *E
Page 35 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
[3:0] to NAK IN-Status OUT mode (1110) after ACKing a valid
status stage OUT token. The firmware needs to update the mode
for the SIE to respond appropriately. See Table 8 for more details
on what modes will be changed by the SIE.
A disabled endpoint will remain disabled until changed by
firmware, and all endpoints reset to the Disabled mode (0000).
Firmware normally enables the endpoint mode after a SetConfiguration request.
Any SETUP packet to an enabled endpoint with mode set to
accept SETUPs will be changed by the SIE to 0001 (NAKing).
Any mode set to accept a SETUP will send an ACK handshake
to a valid SETUP token.
The control endpoint has three status bits for identifying the
token type received (SETUP, IN, or OUT), but the endpoint must
be placed in the correct mode to function as such. Non-control
endpoints should not be placed into modes that accept SETUPs.
Table 9. Decode table for Table 10: “Details of Modes for Differing Traffic Conditions”
Properties of incoming
packet
Endpoint Mode
Encoding
Changes to the internal register made by the SIE as a result of
the incoming token
Interrupt?
End Point
Mode
3
2
1
0
Token
count
buffer
dval
DTOG
DVAL
COUNT
Setup
In
Out
ACK
Data Valid (Bit 6, Figure 18)
The validity of the received data
The number of received
bytes
Legend:
UC: unchanged
TX: transmit
x: don’t care
RX: receive
PID Status Bits
(Bit[7:5], Figure 16)
1
0
Response
Int
Endpoint Mode changed
by the SIE.
Data 0/1 (Bit 7, Figure 18)
The quality status of the DMA buffer
2
SIE’s Response
Bit[3:0], Figure 18
Received Token
(SETUP, IN,OUT)
3
Acknowledge transaction completed
(Bit4,Figure 16/3)
TX0: transmit 0-length packet
available for Control endpoint only
Document #: 38-08022 Rev. *E
Page 36 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
The response of the SIE can be summarized as follows:
1. The SIE will only respond to valid transactions, and will ignore
non-valid ones.
2. The SIE will generate an interrupt when a valid transaction is
completed or when the FIFO is corrupted. FIFO corruption
occurs during an OUT or SETUP transaction to a valid internal
address, that ends with a non-valid CRC.
3. An incoming Data packet is valid if the count is < Endpoint
Size + 2 (includes CRC) and passes all error checking;
4. An IN will be ignored by an OUT configured endpoint and visa
versa.
5. The IN and OUT PID status is updated at the end of a transaction.
6. The SETUP PID status is updated at the beginning of the Data
packet phase.
7. The entire Endpoint 0 mode register and the Count register
are locked to CPU writes at the end of any transaction to that
endpoint in which an ACK is transferred. These registers are
only unlocked by a CPU read of these registers, and only if
that read happens after the transaction completes. This represents about a 1-s window in which the CPU is locked from
register writes to these USB registers. Normally the firmware
should perform a register read at the beginning of the
Endpoint ISRs to unlock and get the mode register information. The interlock on the Mode and Count registers
ensures that the firmware recognizes the changes that the
SIE might have made during the previous transaction.
Table 10. Details of Modes for Differing Traffic Conditions
End Point Mode
3
2
1
PID
Rcved
0 Token
Cou
nt
Buffer
Dval
DTOG
DVAL
COUN
T
SETUP
Set End Point Mode
IN
OU
T
ACK
3
2 1 0 Response
Int
0 0 1 ACK
ye
s
SETUP Packet (if accepting)
See8
SETUP
<=
10
data
valid
updates
1
updates
1
U
C
UC
1
0
See8
SETUP
> 10
junk
x
updates
updates
updates
1
U
C
UC
UC
NoChang
e
Ignore
ye
s
See 8
SETUP
x
junk
invalid
updates
0
updates
1
U
C
UC
UC
NoChang
e
Ignore
ye
s
x
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
Disabled
0
0
0
0 x
NAK IN/OUT
0
0
0
1 OUT
x
UC
x
UC
UC
UC
UC
U
C
1
UC
NoChang
e
NAK
ye
s
0
0
0
1 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
NAK
ye
s
0
0
0
0
0
0
1 OUT
1 IN
x
UC
invalid
UC
UC
UC
UC
x
UC
x
UC
UC
UC
UC
1
UC
UC
NoChang
e
x
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
UC
NoChang
e
Ignore
no
Ignore IN/OUT
0
0
1
1
0
0
0 OUT
0 IN
x
UC
x
UC
UC
UC
UC
U
C
STALL IN/OUT
0
0
1
1 OUT
x
UC
x
UC
UC
UC
UC
U
C
1
UC
NoChang
e
STALL
ye
s
0
0
1
1 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
STALL
ye
s
0
0
0
0
1
1
1 OUT
1 IN
x
UC
invalid
UC
UC
UC
UC
x
UC
x
UC
UC
UC
UC
1
UC
UC
NoChang
e
Control Write
ACK OUT/NAK IN
1
0
1
1 OUT
<=
10
data
valid
updates
1
updates
UC
U
C
1
1
0
1
0
1
1 OUT
> 10
junk
x
updates
updates
updates
UC
U
C
1
UC
NoChang
e
Ignore
ye
s
1
0
1
1 OUT
x
junk
invalid
updates
0
updates
UC
U
C
1
UC
NoChang
e
Ignore
ye
s
Document #: 38-08022 Rev. *E
0 0 1 ACK
ye
s
Page 37 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Table 10. Details of Modes for Differing Traffic Conditions (continued)
1
0
1
1 IN
x
UC
x
UC
UC
UC
UC
1
UC
UC
NoChang
e
NAK
ye
s
NAK OUT/Status IN
1
0
1
0 OUT
<=
10
UC
valid
UC
UC
UC
UC
U
C
1
UC
NoChang
e
NAK
ye
s
1
0
1
0 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
TX 0 Byte
ye
s
1
1
0
0
1
1
0 OUT
0 IN
x
UC
invalid
UC
UC
UC
UC
x
UC
x
UC
UC
UC
UC
1
UC
1
NoChang
e
Status IN Only
0
1
1
0 OUT
<=
10
UC
valid
UC
UC
UC
UC
U
C
1
UC
0
0
1
1
0 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
TX 0 Byte
ye
s
ACK
ye
s
0
0
1
1
1
1
0 OUT
0 IN
x
UC
invalid
UC
UC
UC
UC
0 1 1 STALL
x
UC
x
UC
UC
UC
UC
1
UC
1
NoChang
e
ye
s
Control Read
ACK IN/Status OUT
1
1
1
1 OUT
2
UC
valid
1
1
updates
UC
U
C
1
1
NoChang
e
1
1
1
1 OUT
2
UC
valid
0
1
updates
UC
U
C
1
UC
0
0 1 1 STALL
ye
s
1
1
1
1 OUT
!=2
UC
valid
updates
1
updates
UC
U
C
1
UC
0
0 1 1 STALL
ye
s
1
1
1
1 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
ACK
1 1 0 (back)
ye
s
1
1
1
1
1
1
1 OUT
1 IN
x
UC
invalid
UC
UC
UC
UC
x
UC
x
UC
UC
UC
UC
1
UC
1
1
NAK IN/Status OUT
1
1
1
0 OUT
2
UC
valid
1
1
updates
UC
U
C
1
1
NoChang
e
1
1
1
0 OUT
2
UC
valid
0
1
updates
UC
U
C
1
UC
0
0 1 1 STALL
3
2
1
0 token
coun
t
buffer
dval
DTOG
DVAL
COUN
T
SETUP
IN
OU
T
ACK
3
2 1 0 response
int
valid
updates
1
updates
UC
U
C
0 1 1 STALL
ye
s
UC
U
C
UC
U
C
1
1
1
1
1
1
1
1
1
1
1
1
0 OUT
0 OUT
0 OUT
0 IN
!=2
> 10
x
UC
UC
UC
x
invalid
UC
UC
UC
UC
UC
UC
1
UC
UC
ACK
ye
s
ye
s
UC
0
UC
NoChang
e
Ignore
no
UC
NoChang
e
Ignore
no
NAK
ye
s
ACK
ye
s
x
UC
x
UC
UC
UC
UC
1
UC
UC
NoChang
e
Status OUT Only
0
0
1
0 OUT
2
UC
valid
1
1
updates
UC
U
C
1
1
NoChang
e
0
0
1
0 OUT
2
UC
valid
0
1
updates
UC
U
C
1
UC
0
0 1 1 STALL
ye
s
0
0
1
0 OUT
!=2
UC
valid
updates
1
updates
UC
U
C
1
UC
0
0 1 1 STALL
ye
s
0
0
1
0 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
UC
NoChang
e
Ignore
no
UC
UC
0
0 1 1 STALL
ye
s
0
0
1
0 OUT
x
UC
invalid
UC
UC
UC
UC
U
C
0
0
1
0 IN
x
UC
x
UC
UC
UC
UC
1
Document #: 38-08022 Rev. *E
Page 38 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Table 10. Details of Modes for Differing Traffic Conditions (continued)
OUT Endpoint
ACK OUT, STALL Bit = 0 (Figure )
1
0
0
1 OUT
<=
10
data
valid
updates
1
updates
UC
U
C
1
1
1
1
0
0
1 OUT
> 10
junk
x
updates
updates
updates
UC
U
C
1
UC
NoChang
e
Ignore
ye
s
1
0
0
1 OUT
x
junk
invalid
updates
0
updates
UC
U
C
1
UC
NoChang
e
Ignore
ye
s
1
0
0
1 IN
x
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
0 0 0 ACK
ye
s
ACK OUT, STALL Bit = 1 (Figure )
1
0
0
1 OUT
<=
10
UC
valid
UC
UC
UC
UC
U
C
1
UC
NoChang
e
STALL
ye
s
1
0
0
1 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
UC
UC
NoChang
e
Ignore
no
1
1
0
0
0
0
1 OUT
x
UC
invalid
UC
UC
UC
1 IN
x
UC
x
UC
UC
UC
UC
U
C
UC
NAK OUT
1
0
0
0 OUT
<=
10
UC
valid
UC
UC
UC
UC
U
C
1
UC
NoChang
e
NAK
ye
s
1
0
0
0 OUT
> 10
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
U
C
UC
NoChang
e
Ignore
no
UC
UC
NoChang
e
Ignore
no
1
1
0
0
0
0
0 OUT
x
UC
invalid
UC
UC
UC
0 IN
x
UC
x
UC
UC
UC
UC
U
C
UC
Reserved
0
1
0
1 OUT
x
updates
updates
updates
updates
updates
UC
U
C
1
1
NoChang
e
RX
ye
s
0
1
0
1 IN
x
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
ACK
1 0 0 (back)
ye
s
IN Endpoint
ACK IN, STALL Bit = 0 (Figure )
1
1
1
1
0
0
1 OUT
1 IN
x
x
UC
UC
x
UC
UC
UC
UC
1
UC
1
1
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
STALL
ye
s
ACK IN, STALL Bit = 1 (Figure )
1
1
1
1
0
0
1 OUT
x
UC
1 IN
x
UC
x
UC
UC
UC
UC
1
UC
UC
NoChang
e
0 OUT
x
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
NAK
ye
s
NAK IN
1
1
1
1
0
0
0 IN
x
UC
x
UC
UC
UC
UC
1
UC
UC
NoChang
e
1 Out
x
UC
x
UC
UC
UC
UC
U
C
UC
UC
NoChang
e
Ignore
no
UC
NoChang
e
TX
ye
s
Reserved
0
0
1
1
1
1
1 IN
x
Document #: 38-08022 Rev. *E
UC
x
UC
UC
UC
UC
1
UC
Page 39 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Register Summary
Register Name
Bit 6
Bit 5
Bit 3
Bit 2
Bit 1
Bit 0
Read/Write/
Both/
Default/
Reset
Port 0 Data
P0
BBBBBBBB
00000000
Port 1 Data
P1
BBBBBBBB
00000000
0x02
Port 2 Data
--RR--RR
00000000
0x0A
GPIO Port 0 Mode 0
P0[7:0] Mode0
WWWWWWWW
00000000
0x0B
GPIO Port 0 Mode 1
P0[7:0] Mode1
WWWWWWWW
00000000
0x0C
GPIO Port 1 Mode 0
P1[7:0] Mode0
WWWWWWWW
00000000
0x0D
GPIO Port 1 Mode 1
P1[7:0] Mode1
WWWWWWWW
00000000
0x04
Port 0 Interrupt Enable
P0[7:0] Interrupt Enable
WWWWWWWW
00000000
0x05
Port 1 Interrupt Enable
P1[7:0] Interrupt Enable
WWWWWWWW
00000000
0x06
Port 0 Interrupt Polarity
P0[7:0] Interrupt Polarity
WWWWWWWW
00000000
0x07
Port 1 Interrupt Polarity
P1[7:0] Interrupt Polarity
WWWWWWWW
00000000
0xF8
Clock Configuration
BBBBBBBB
00000000
0x10
USB Device Address
Device
Address
Enable
BBBBBBBB
00000000
0x12
EP0 Mode
SETUP
Received
0x14,
0x16
EP1, EP2 Mode Register
0x11,
EP0,1, and 2 Counter
0x13, and
0x15
Reserved
Ext. Clock
Resume
Delay
STALL
D+(SCLK)
State
Wake-up Timer Adjust Bit [2:0]
IN
Received
OUT
Received
Reserved
Data 0/1
Toggle
Data Valid
USB Status and Control
PS/2 Pull-up
Enable
VREG
Enable
0x20
Global Interrupt Enable
Wake-up
Interrupt
Enable
GPIO
Interrupt
Enable
0x21
Endpoint Interrupt Enable
Timer (MSB)
Low-voltage
Reset
Disable
P2.1 (Int Clk
Mode Only
Precision
USB
Clocking
Enable
VREG Pin
State
Internal
Clock
Output
Disable
External
Oscillator
Enable
ACKed
Transaction
Mode Bit
BBBBBBBB
00000000
ACKed
Transaction
Mode Bit
B--BBBBB
00000000
Byte Count
BB--BBBB
00000000
D+/D- Forcing Bit
BBB-BBBB
00000000
1.024 ms
Interrupt
Enable
128 s
Interrupt
Enable
USB Bus
Reset-PS/2
Activity Intr.
Enable
BBBBBBBB
00000000
EP2
Interrupt
Enable
EP1
Interrupt
Enable
EP0
Interrupt
Enable
-----BBB
00000000
RRRRRRRR
00000000
----RRRR
00000000
BBBBBBBB
00000000
BBBBBBBB
00000000
Reserved
USB
Reset-PS/2
Activity
Interrupt
Mode
Reserved
Capture
Capture
Timer B Intr. Timer A Intr.
Enable
Enable
USB Bus
Activity
SPI
Interrupt
Enable
Reserved
Timer Bit [7:0]
0x25
0x60
SPI Data
0x61
SPI Control
0x40
Capture Timer A-Rising,
Data Register
Capture A Rising Data
RRRRRRRR
00000000
0x41
Capture Timer A-Falling,
Data Register
Capture A Falling Data
RRRRRRRR
00000000
0x42
Capture Timer B-Rising,
Data Register
Capture B Rising Data
RRRRRRRR
00000000
0x43
Capture Timer B-Falling,
Data Register
Capture B Falling Data
RRRRRRRR
00000000
0x44
Capture Timer
Configuration
0x45
Capture Timer Status
0xFF
Process Status & Control
PROC
SC.
CAPTURE TIMER
TIMER
Timer LSB
Reserved
Device Address
0x1F
0x24
D- (SDATA)
State
SPI
INTERRUPT
Bit 4
0x00
USBSC
ENDPOINT 0, I AND 2
CONFIGURATION
Bit 7
0x01
Clock
Config.
GPIO CONFIGURATION PORTS 0, 1 AND 2
Address
Document #: 38-08022 Rev. *E
Reserved
Timer Bit [11:8]
Data I/O
TCMP
First Edge
Hold
TBF
Comm Mode [1:0]
Prescale Bit [2:0]
Reserved
IRQ
Pending
Watch Dog
Reset
Bus
Interrupt
Event
LVR/BOR
Reset
CPOL
CPHA
SCK Select
Capture B
Falling Intr
Enable
Capture B
Rising Intr
Enable
Capture A
Falling Intr
Enable
Capture A
Rising Intr
Enable
BBBBBBBB
00000000
Capture B
Falling
Event
Capture B
Rising Event
Capture A
Falling
Event
Capture A
Rising Event
----BBBB
00000000
Suspend
Interrupt
Enable
Sense
Reserved
Run
RBBBBR-B
See
Section
Page 40 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Absolute Maximum Ratings
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with Power Applied...... –0°C to +70°C
Supply Voltage on VCC Relative to VSS ..........–0.5V to +7.0V
DC Input Voltage .................................. –0.5V to +VCC+0.5V
DC Voltage Applied to Outputs in High Z State –0.5V to + VCC+0.5V
Maximum Total Sink Output Current into Port 0 and 1 and Pins70 mA
Maximum Total Source Output Current into Port 0 and 1 and Pins30 mA
Maximum On-chip Power Dissipation on any GPIO Pin50 mW
Power Dissipation..................................................... 300 mW
Static Discharge Voltage .......................................... > 2000V
Latch-up Current ................................................... > 200 mA
DC Characteristics FOSC = 6 MHz; Operating Temperature = 0 to 70°C
Parameter
Conditions
Min.
Max.
Unit
General
VCC1
Operating Voltage
Note 4
VLVR
5.5
V
VCC2
Operating Voltage
Note 4
4.35
5.25
V
ICC1
VCC Operating Supply Current – Internal
Oscillator Mode
Typical ICC1 = 16 mA[5]
VCC = 5.5V, no GPIO loading
20
mA
ICC2
VCC Operating Supply Current – External
Oscillator Mode
Typical ICC2= 13 mA[5]
17
mA
VCC = 5.0V. T = Room Temperature
VCC = 5.5V, no GPIO loading
VCC = 5.0V. T = Room Temperature
ISB1
Standby Current – No Wake-up Osc
Oscillator off, D– > 2.7V
25
A
ISB2
Standby Current – With Wake-up Osc
Oscillator off, D– > 2.7V
75
A
VPP
Programming Voltage (disabled)
TRSNTR
Resonator Start-up Interval
VCC = 5.0V, ceramic resonator
IIL
Input Leakage Current
Any I/O pin
1
A
ISNK
Max ISS GPIO Sink Current
Cumulative across all ports[6]
70
mA
ISRC
Max ICC GPIO Source Current
Cumulative across all ports[6]
30
mA
VLVR
Low-Voltage Reset Trip Voltage
4.0
V
100
ms
3.6
V
300
pF
3.6
V
–0.4
0.4
V
256
s
Low-Voltage and Power-on Reset
VCC below VLVR for >100 ns[7]
tVCCS
VCC Power-on Slew Time
VREG
VREG Regulator Output Voltage
Load = RPU +RPD[9, 10]
CREG
Capacitance on VREG Pin
External cap not required
VOHU
Static Output High, driven
RPD to Gnd[4]
linear ramp: 0 to
3.5
4V[8]
USB Interface
3.0
2.8
Notes
4. Full functionality is guaranteed in VCC1 range, except USB transmitter specifications and GPIO output currents are guaranteed for VCC2 range.
5. Bench measurements taken under nominal operating conditions. Spec cannot be guaranteed at final test.
6. Total current cumulative across all Port pins, limited to minimize Power and Ground-Drop noise effects.
7. LVR is automatically disabled during suspend mode.
8. LVR will re-occur whenever VCC drops below VLVR. In suspend or with LVR disabled, BOR occurs whenever VCC drops below approximately 2.5V.
9. VREG specified for regulator enabled, idle conditions (i.e., no USB traffic), with load resistors listed. During USB transmits from the internal SIE, the VREG output
is not regulated, and should not be used as a general source of regulated voltage in that case. During receive of USB data, the VREG output drops when D– is
LOW due to internal series resistance of approximately 200 at the VREG pin.
10. In suspend mode, VREG is only valid if RPU is connected from D– to VREG pin, and RPD is connected from D– to ground.
Document #: 38-08022 Rev. *E
Page 41 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
DC Characteristics FOSC = 6 MHz; Operating Temperature = 0 to 70°C (continued)
Parameter
Conditions
Min.
VOLU
Static Output Low
With RPU to VREG pin
VOHZ
Static Output High, idle or suspend
RPD connected D– to Gnd, RPU
connected D– to VREG pin[4]
2.7
VDI
Differential Input Sensitivity
|(D+)–(D–)|
0.2
Max.
Unit
0.3
V
3.6
V
V
VCM
Differential Input Common Mode Range
0.8
2.5
V
VSE
Single Ended Receiver Threshold
0.8
2.0
V
CIN
Transceiver Capacitance
20
pF
ILO
Hi-Z State Data Line Leakage
0 V < Vin<3.3 V (D+ or D– pins)
–10
10
A
RPU
External Bus Pull-up resistance (D–)
1.3 k ±2% to VREG[11]
1.274
1.326
k
RPD
External Bus Pull-down resistance
15 k±5% to Gnd
14.25
15.75
k
PS/2 Interface
VOLP
Static Output Low
Isink = 5 mA, SDATA or SCLK pins
RPS2
Internal PS/2 Pull-up Resistance
SDATA, SCLK pins, PS/2 Enabled
RUP
Pull-up Resistance
0.4
V
3
7
k
8
24
k
General Purpose I/O Interface
VICR
Input Threshold Voltage, CMOS mode
Low to high edge, Port 0 or 1
40%
60%
VCC
VICF
Input Threshold Voltage, CMOS mode
High to low edge, Port 0 or 1
35%
55%
VCC
VHC
Input Hysteresis Voltage, CMOS mode
High to low edge, Port 0 or 1
3%
10%
VCC
VITTL
Input Threshold Voltage, TTL mode
Ports 0, 1, and 2
0.8
2.0
V
0.8
0.4
V
V
1[4]
1[4]
VOL1A
VOL1B
Output Low Voltage, high drive mode
IOL1 = 50 mA, Ports 0 or
IOL1 = 25 mA, Ports 0 or
VOL2
Output Low Voltage, medium drive mode
IOL2 = 8 mA, Ports 0 or 1[4]
0.4
V
VOL3
Output Low Voltage, low drive mode
IOL3 = 2 mA, Ports 0 or 1[4]
0.4
V
mA[4]
VOH
Output High Voltage, strong drive mode
Port 0 or 1, IOH = 2
RXIN
Pull-down resistance, XTALIN pin
Internal Clock Mode only
VCC–2
V
50
k
Note
11. The 200 internal resistance at the VREG pin gives a standard USB pull-up using this value. Alternately, a 1.5 k,5%pull-up from D– to an external 3.3V supply can
be used.
Document #: 38-08022 Rev. *E
Page 42 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Switching Characteristics
Parameter
FICLK
FICLK2
TCYC
TCH
TCL
tSTART
tWAKE
tWATCH
TR
TR
TF
TF
TRFM
VCRS
Description
Internal Clock Mode
Internal Clock Frequency
Internal Clock Frequency, USB
mode
External Oscillator Mode
Input Clock Cycle Time
Clock HIGH Time
Clock LOW Time
Reset Timing
Time-out Delay after LVR/BOR
Internal Wake-up Period
WatchDog Timer Period
USB Driver Characteristics
Transition Rise Time
Transition Rise Time
Transition Fall Time
Transition Fall Time
Rise/Fall Time Matching
Output Signal Crossover
Voltage[18]
TDRATE
TDJR1
TDJR2
TDEOP
TEOPR2
TEOPT
TUDJ1
TUDJ2
TLST
USB Data Timing
Low Speed Data Rate
Receiver Data Jitter Tolerance
Receiver Data Jitter Tolerance
Differential to EOP transition Skew
EOP Width at Receiver
Source EOP Width
Differential Driver Jitter
Differential Driver Jitter
Width of SE0 during Diff. Transition
TFPS2
Non-USB Mode Driver
Characteristics
SDATA/SCK Transition Fall Time
TSMCK
TSSCK
SPI Timing
SPI Master Clock Rate
SPI Slave Clock Rate
Conditions
Min.
Max.
Unit
Internal Clock Mode enabled
Internal Clock Mode enabled, Bit 2 of register
0xF8h is set (Precision USB Clocking)[12]
5.7
5.91
6.3
6.09
MHz
MHz
USB Operation, with External ±1.5%
Ceramic Resonator or Crystal
164.2
169.2
ns
0.45 tCYC
0.45 tCYC
Enabled Wake-up
FOSC = 6 MHz
Interrupt[13]
CLoad = 200 pF (10% to 90%[4])
CLoad = 600 pF (10% to 90%[4])
CLoad = 200 pF (10% to 90%[4])
CLoad = 600 pF (10% to 90%[4])
tr/tf[4, 14]
CLoad = 200 to 600 pF[4]
Ave. Bit Rate (1.5 Mb/s ±1.5%)
To Next Transition[15]
For Paired Transitions[15]
Note 15
Accepts as EOP[15]
To next transition, Figure 46
To paired transition, Figure 46
24
1
10.1
ns
ns
60
5
14.6
75
300
75
80
1.3
300
125
2.0
ms
ms
ms
ns
ns
ns
ns
%
V
1.4775
–75
–45
–40
670
1.25
–95
–150
1.5225
75
45
100
1.50
95
150
210
Mb/s
ns
ns
ns
ns
s
ns
ns
ns
50
300
ns
2
2.2
MHz
MHz
Note 16
CLoad = 150 pF to 600 pF
See Figures 47 to 50[17]
FCLK/3; see Figure 20
Notes
12. Initially FICLK2 = FICLK until a USB packet is received.
13. Wake-up time for Wake-up Adjust Bits cleared to 000b (minimum setting)
14. Tested at 200 pF.
15. Measured at cross-over point of differential data signals.
16. Non-USB Mode refers to driving the D–/SDATA and/or D+/SCLK pins with the Control Bits of the USB Status and Control Register, with Control Bit 2 HIGH.
17. SPI timing specified for capacitive load of 50 pF, with GPIO output mode = 01 (medium low drive, strong high drive).
18. Per the USB 2.0 Specification, Table 7.7, Note 10, the first transition from the Idle state is excluded.
Document #: 38-08022 Rev. *E
Page 43 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Switching Characteristics (continued)
Parameter
TSCKH
TSCKL
TMDO
TMDO1
TMSU
TMHD
TSSU
TSHD
TSDO
TSDO1
TSSS
TSSH
Description
SPI Clock High Time
SPI Clock Low Time
Master Data Output Time
Master Data Output Time,
First bit with CPHA = 1
Master Input Data Set-up time
Master Input Data Hold time
Slave Input Data Set-up Time
Slave Input Data Hold Time
Slave Data Output Time
Slave Data Output Time,
First bit with CPHA = 1
Slave Select Set-up Time
Slave Select Hold Time
Conditions
High for CPOL = 0, Low for CPOL = 1
Low for CPOL = 0, High for CPOL = 1
SCK to data valid
Time before leading SCK edge
Min.
125
125
–25
100
Max.
50
50
50
50
50
SCK to data valid
Time after SS LOW to data valid
Before first SCK edge
After last SCK edge
100
100
150
150
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Figure 42. Clock Timing
TCYC
TCH
CLOCK
TCL
Figure 43. USB Data Signal Timing
Voh
90%
Vcrs
Vol
Document #: 38-08022 Rev. *E
TF
TR
D
10%
90%
10%
D
Page 44 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 44. Receiver Jitter Tolerance
TPERIOD
Differential
Data Lines
TJR
TJR1
TJR2
Consecutive
Transitions
N * TPERIOD + TJR1
Paired
Transitions
N * TPERIOD + TJR2
Figure 45. Differential to EOP Transition Skew and EOP Width
TPERIOD
Differential
Data Lines
Crossover
Point Extended
Crossover
Point
Diff. Data to
SE0 Skew
N * TPERIOD + TDEOP
Source EOP Width:
TEOPT
Receiver EOP Width: TEOPR1, TEOPR2
Figure 46. Differential Data Jitter
TPERIOD
Differential
Data Lines
Crossover
Points
Consecutive
Transitions
N * TPERIOD + TxJR1
Paired
Transitions
N * TPERIOD + TxJR2
Document #: 38-08022 Rev. *E
Page 45 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 47. SPI Master Timing, CPHA = 0
SS
(SS is under firmware control in SPI Master mode)
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
TMDO
MOSI
MSB
MISO
MSB
LSB
LSB
TMSU TMHD
Figure 48. SPI Slave Timing, CPHA = 0
SS
TSSS
TSSH
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
MOSI
MSB
TSDO
MISO
Document #: 38-08022 Rev. *E
LSB
TSSU TSHD
MSB
LSB
Page 46 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 49. SPI Master Timing, CPHA = 1
SS
(SS is under firmware control in SPI Master mode)
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
TMDO
TMDO1
MOSI
MSB
LSB
MSB
MISO
LSB
TMSU TMHD
Figure 50. SPI Slave Timing, CPHA = 1
SS
TSSH
TSSS
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
MSB
MOSI
LSB
TSSU TSHD
TSDO1
MISO
Document #: 38-08022 Rev. *E
MSB
TSDO
LSB
Page 47 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Ordering Information
Ordering Code
EPROM
Size
Package
Name
Package Type
Operating
Range
CY7C63723C-PXC
8 KB
P3
18-Pin (300-Mil) Lead-free PDIP
Commercial
CY7C63723C-SXC
8 KB
S3
18-Pin Small Outline Lead-free Package
Commercial
CY7C63743C-PXC
8 KB
P13
24-Pin (300-Mil) Lead-free PDIP
Commercial
CY7C63743C-SXC
8 KB
S13
24-Pin Small Outline Lead-free Package
Commercial
CY7C63743C-QXC
8 KB
Q13
24-lead QSOP Lead-free Package
Commercial
CY7C63722C-XC
8 KB
–
25-Pad DIE Form
Commercial
Package Diagrams
Figure 51. 18-Pin PDIP (300-Mil) Molded DIP
51-85010 *C
Document #: 38-08022 Rev. *E
Page 48 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 52. 18L SOIC .463 X.300 X .0932 Inches
51-85023 *C
Figure 53. 24-Pin SOIC (.615 X .300 X .0932 Inches
51-85025 *E
Document #: 38-08022 Rev. *E
Page 49 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 54. 24-Pin PDIP 1.260 X .270 X .140 I
51-85013 *C
Figure 55. 24-Pin QSOP 8.65 X 3.9 X 1.44 MM
51-85055 *C
Document #: 38-08022 Rev. *E
Page 50 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Figure 56. Die Form
Cypress Logo
(1907, 3001)
3
2
1
25
24
23
Die Step: 1907 x 3011 microns
Die Size: 1830.8 x 2909 microns
Die Thickness: 14 mils = 355.6 microns
Pad Size: 80 x 80 microns
10
17
(0,0)
13
14
15
16
22
21
20
19
18
11
12
Y
4
5
6
7
8
9
X
Table 11 below shows the die pad coordinates for the CY7C63722C-XC. The center location of each bond pad is relative to the bottom
left corner of the die which has coordinate (0,0).
Table 11. CY7C63722C-XC Probe Pad Coordinates in microns ((0,0) to bond pad centers)
Pad Number
Pin Name
X
(microns)
Y
(microns)
1
P0.0
788.95
2843.15
2
P0.1
597.45
2843.15
3
P0.2
406.00
2843.15
4
P0.3
154.95
2687.95
5
P1.0
154.95
2496.45
6
P1.2
154.95
2305.05
7
P1.4
154.95
2113.60
8
P1.6
154.95
1922.05
9
Vss
154.95
1730.90
10
Vss
154.95
312.50
11
Vpp
363.90
184.85
12
VREG
531.70
184.85
13
XTALIN
1066.55
184.85
14
XTALOUT
1210.75
184.85
15
Vcc
1449.75
184.85
16
D–
1662.35
184.85
17
D+
1735.35
289.85
18
P1.7
1752.05
1832.75
19
P1.5
1752.05
2024.30
20
P1.3
1752.05
2215.75
21
P1.1
1752.05
2407.15
22
P0.7
1752.05
2598.65
23
P0.6
1393.25
2843.15
24
P0.5
1171.80
2843.15
25
P0.4
980.35
2843.15
Document #: 38-08022 Rev. *E
Page 51 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Document History Page
Document Title: CY7C63722C, CY7C63723C, CY7C63743C enCoRe™ USB Combination Low-Speed USB
and PS/2 Peripheral Controller
Document Number: 38-08022
REV.
ECN NO.
Issue Date
Orig. of
Change
**
118643
10/22/02
BON
Converted from Spec 38-00944 to Spec 38-08022.
Added notes 17, 18 to section 26
Removed obsolete parts (63722-PC and 63742)
Added die sale
Added section 23 (Register Summary)
*A
243308
SEE ECN
KKU
Added 24 QSOP package
Added Lead-free packages to section 27
Reformatted to update format
*B
267229
See ECN
ARI
Corrected part number in the Ordering Information section
*C
429169
See ECN
TYJ
Updated part numbers with ‘C’ part numbers
Changed to ‘Cypress Perform’ logo
Added the 24-QSOP part offering
*D
3057657
10/13/2010
AJHA
Added “Not recommended for new designs” watermark in the PDF.
Updated package diagrams.
Updated template.
*E
3229083
04/15/2011
NXZ
Sunset Review. No technical updates.
Package diagram updated 51-85025 *E
Document #: 38-08022 Rev. *E
Description of Change
Page 52 of 53
[+] Feedback
CY7C63722C
CY7C63723C
CY7C63743C
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
psoc.cypress.com/solutions
cypress.com/go/clocks
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/interface
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2004-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 38-08022 Rev. *E
Revised April 15, 2011
Page 53 of 53
enCoRe is a trademark of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback