ONSEMI MC100E210FNR2

MC100E210
5VECL Dual 1:4, 1:5
Differential Fanout Buffer
The MC100E210 is a low voltage, low skew dual differential ECL
fanout buffer designed with clock distribution in mind. The device
features two fanout buffers, a 1:4 and a 1:5 buffer, on a single chip. The
device features fully differential clock paths to minimize both device and
system skew. The dual buffer allows for the fanout of two signals through
a single chip, thus reducing the skew between the two fundamental
signals from a part−to−part skew down to an output−to−output skew. This
capability reduces the skew by a factor of 4 as compared to using two
LVE111’s to accomplish the same task.
The lowest TPD delay time results from terminating only one output
pair, and the greatest TPD delay time results from terminating all the
output pairs. This shift is about 10−20 pS in TPD. The skew between
any two output pairs within a device is typically about 25 nS. If other
output pairs are not terminated, the lowest TPD delay time results
from both output pairs and the skew is typically 25 nS. When all
outputs are terminated, the greatest TPD (delay time) occurs and all
outputs display about the same 10−20 pS increase in TPD, so the
relative skew between any two output pairs remains about 25 nS.
For more information on using PECL, designers should refer to
Application Note AN1406/D.
The VBB pin, an internally generated voltage supply, is available to this
device only. For single-ended input conditions, the unused differential
input is connected to VBB as a switching reference voltage. VBB may also
rebias AC coupled inputs. When used, decouple VBB and VCC via a
0.01 F capacitor and limit current sourcing or sinking to 0.5 mA. When
not used, VBB should be left open.
• Dual Differential Fanout Buffers
• 200 ps Part−to−Part Skew
• 50 ps Typical Output−to−Output Skew
• Low Voltage ECL/PECL Compatible
• The 100 Series Contains Temperature Compensation
• 28−lead PLCC Packaging
• PECL Mode Operating Range: VCC = 4.2 V to 5.7 V with VEE = 0 V
• NECL Mode Operating Range: VCC = 0 V with VEE = −4.2 V to −5.7 V
• Internal Input 75 K Pulldown Resistors
• Q Output will Default LOW with Inputs Open or at VEE
• ESD Protection: Human Body Model; >2 KV,
Machine Model; >200 V
• Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
• Moisture Sensitivity Level 1
For Additional Information, see Application Note AND8003/D
• Flammability Rating: UL 94 V−0 @ 0.125 in,
Oxygen Index: 28 to 34
• Transistor Count = 179 devices
 Semiconductor Components Industries, LLC, 2003
October, 2003 − Rev. 2
1
http://onsemi.com
MARKING
DIAGRAM
1 28
MC100E210FN
AWLYYWW
PLCC−28
FN SUFFIX
CASE 776
A
WL
YY
WW
= Assembly Location
= Wafer Lot
= Year
= Work Week
*For additional information, see Application Note
AND8002/D
ORDERING INFORMATION
Package
Shipping†
MC100E210FN
PLCC−28
37 Units / Rail
MC100E210FNR2
PLCC−28 500 Tape & Reel
Device
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
Publication Order Number:
MC100E210/D
MC100E210
LOGIC DIAGRAM AND PINOUT ASSIGNMENT
Qa0 Qa0 Qa1 VCCO Qa1 Qa2 Qa2
25
24
23
22
21
20
19
VEE
26
18
Qa3
VBB
27
17
Qa3
CLKa
28
16
Qb0
15
VCCO
VCC
28−Lead PLCC
(Top View)
1
CLKa
2
14
Qb0
CLKb
3
13
Qb1
CLKb
4
12
Qb1
LOGIC SYMBOL
Qa0
Qa0
CLKa
Qa1
CLKa
Qa1
Qa2
Qa2
Qa3
5
6
7
8
9
10
Qa3
11
Qb0
Qb4 Qb4 Qb3 VCCO Qb3 Qb2 Qb2
Qb0
Warning: All VCC, VCCO, and VEE pins must be externally
connected to Power Supply to guarantee proper operation.
CLKb
Qb1
CLKb
Qb1
Qb2
PIN DESCRIPTION
PIN
FUNCTION
CLKa, CLKb
CLKa, CLKb
Qa0:3, Qb0:4
Qa0:3, Qb0:4
VBB
VCC, VCCO
VEE
ECL Differential Input Pairs
ECL Differential Input Pairs
ECL Differential Outputs
ECL Differential Outputs
Reference Output Voltage
Positive Supply
Negative Supply
Qb2
Qb3
Qb3
Qb4
Qb4
VBB
MAXIMUM RATINGS (Note 1)
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE = 0 V
8
V
VEE
NECL Mode Power Supply
VCC = 0 V
−8
V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
6
−6
V
V
Iout
Output Current
Continuous
Surge
50
100
mA
mA
IBB
VBB Sink/Source
± 0.5
mA
TA
Operating Temperature Range
0 to +85
°C
Tstg
Storage Temperature Range
−65 to +150
°C
JA
Thermal Resistance (Junction−to−Ambient)
0 LFPM
500 LFPM
28 PLCC
28 PLCC
63.5
43.5
°C/W
°C/W
JC
Thermal Resistance (Junction−to−Case)
Standard Board
28 PLCC
22 to 26
°C/W
VEE
PECL Operating Range
NECL Operating Range
4.2 to 5.7
−5.7 to −4.2
V
V
Tsol
Wave Solder
265
°C
<2 to 3 sec @ 248°C
1. Maximum Ratings are those values beyond which device damage may occur.
http://onsemi.com
2
VI VCC
VI VEE
MC100E210
PECL DC CHARACTERISTICS VCCx= 5.0 V; VEE= 0.0 V (Note 2)
−40°C
Symbol
Characteristic
Min
25°C
Typ
Max
Min
Typ
55
85°C
Max
Min
Typ
55
Max
Unit
65
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 3)
3915
3995
4120
3975
4050
4120
3975
4050
4120
mV
VOL
Output LOW Voltage (Note 3)
3170
3305
3445
3190
3255
3380
3190
3260
3380
mV
VIH
Input HIGH Voltage (Single−Ended)
3835
3975
4120
3835
3975
4120
3835
3975
4120
mV
VIL
Input LOW Voltage (Single−Ended)
3190
3355
3525
3190
3355
3525
3190
3355
3525
mV
VBB
Output Voltage Reference
3.62
3.74
3.62
3.74
3.62
3.74
V
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential) (Note 4)
2.7
4.6
2.7
4.6
2.7
4.6
V
IIH
Input HIGH Current
150
A
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.25
0.5
A
0.2
NOTE:
Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
2. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
3. Outputs are terminated through a 50 resistor to VCC − 2 volts.
4. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
NECL DC CHARACTERISTICS VCCx= 0.0 V; VEE= −5.0 V (Note 5)
−40°C
Symbol
Characteristic
Min
Typ
25°C
Max
Min
Typ
55
85°C
Max
Min
Typ
55
Max
Unit
65
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 6)
−1085
−1005
−880
−1025
−950
−880
−1025
−950
−880
mV
VOL
Output LOW Voltage (Note 6)
−1830
−1695
−1555
−1810
−1745
−1620
−1810
−1740
−1620
mV
VIH
Input HIGH Voltage (Single−Ended)
−1165
−1025
−880
−1165
−1025
−880
−1165
−1025
−880
mV
VIL
Input LOW Voltage (Single−Ended)
−1810
−1645
−1475
−1810
−1645
−1475
−1810
−1645
−1475
mV
VBB
Output Voltage Reference
−1.38
−1.26
−1.38
−1.26
−1.38
−1.26
V
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration) (Note 7)
−2.3
−0.4
−2.3
−0.4
−2.3
−0.4
V
IIH
Input HIGH Current
150
A
IIL
Input LOW Current
150
0.5
0.3
NOTE:
150
0.5
0.25
0.5
0.2
A
Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
5. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
6. Outputs are terminated through a 50 resistor to VCC − 2 volts.
7. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
http://onsemi.com
3
MC100E210
AC CHARACTERISTICS VCCx= 5.0 V; VEE= 0.0 V or VCCx= 0.0 V; VEE= −5.0 V (Note 8)
−40°C
Symbol
Characteristic
Min
Typ
fMAX
Maximum Toggle Frequency
tPLH
tPHL
Propagation Delay to Output
IN (differential) (Note 9)
IN (single−ended) (Note 10)
tskew
Within−Device Skew
Qa to Qb
Qa to Qa,Qb to Qb
Part−to−Part Skew (Differential) (Note 11)
50
50
tJITTER
Random Clock Jitter (RMS)
<1
VPP
Input Voltage Swing (Differential Configuration)
(Note 12)
500
tr / tf
Output Rise/Fall Time (20%−80%)
200
25°C
Max
Min
700
Typ
85°C
Max
Min
700
Typ
Max
700
Unit
MHz
ps
475
400
675
700
500
450
75
75
200
700
750
50
30
500
450
75
50
200
50
30
<1
200
75
50
200
<1
500
600
700
750
ps
500
600
200
ps
mV
600
ps
8. VEE can vary −0.46 V / +0.8 V.
9. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the
differential output signals.
10. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
11. The within−device skew is defined as the worst case difference between any two similar delay paths within a single device.
12. VPP(min) is defined as the minimum input differential voltage which will cause no increase in the propagation delay. The VPP(min) is AC limited
for the E210 as a differential input as low as 50 mV will still produce full ECL levels at the output.
http://onsemi.com
4
MC100E210
Q
D
Receiver
Device
Driver
Device
Q
D
50 50 V TT
VTT = VCC − 2.0 V
Figure 1. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020 − Termination of ECL Logic Devices.)
Resource Reference of Application Notes
AN1404
−
ECLinPS Circuit Performance at Non−Standard VIH Levels
AN1405
−
ECL Clock Distribution Techniques
AN1406
−
Designing with PECL (ECL at +5.0 V)
AN1503
−
ECLinPS I/O SPICE Modeling Kit
AN1504
−
Metastability and the ECLinPS Family
AN1568
−
Interfacing Between LVDS and ECL
AN1596
−
ECLinPS Lite Translator ELT Family SPICE I/O Model Kit
AN1650
−
Using Wire−OR Ties in ECLinPS Designs
AN1672
−
The ECL Translator Guide
AND8001
−
Odd Number Counters Design
AND8002
−
Marking and Date Codes
AND8020
−
Termination of ECL Logic Devices
http://onsemi.com
5
MC100E210
PACKAGE DIMENSIONS
PLCC−28
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776−02
ISSUE E
0.007 (0.180)
B
Y BRK
-N-
T L −M
M
M
0.007 (0.180)
U
S
N
T L −M
S
S
N
S
D
Z
-L-
-M-
D
W
X
V
28
1
G1
0.010 (0.250)
S
T L −M
S
N
S
VIEW D-D
Z
C
A
0.007 (0.180)
R
0.007 (0.180)
M
M
T L −M
S
T L −M
S
N
S
N
S
H
M
0.007 (0.180)
T L −M
N
S
K1
E
0.004 (0.100)
G
J
S
K
SEATING
PLANE
F
VIEW S
G1
0.010 (0.250)
-T-
T L −M
S
N
0.007 (0.180)
VIEW S
S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIM G1, TRUE POSITION TO BE MEASURED
AT DATUM -T-, SEATING PLANE.
3. DIM R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
http://onsemi.com
6
INCHES
MIN
MAX
0.485 0.495
0.485 0.495
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
0.020
0.025
0.450 0.456
0.450 0.456
0.042 0.048
0.042 0.048
0.042 0.056
0.020
10°
2°
0.410 0.430
0.040
MILLIMETERS
MIN
MAX
12.32 12.57
12.32 12.57
4.57
4.20
2.79
2.29
0.48
0.33
1.27 BSC
0.81
0.66
0.51
0.64
11.58
11.43
11.58
11.43
1.21
1.07
1.21
1.07
1.42
1.07
0.50
10°
2°
10.42 10.92
1.02
M
T L −M
S
N
S
S
MC100E210
Notes
http://onsemi.com
7
MC100E210
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
8
For additional information, please contact your
local Sales Representative.
MC100E210/D