GaAs SPDT Absorptive Switch with ASIC Driver, DC - 3.0 GHz SW65-0114 V 5.00 Features n n n n n n n n SOW-24 Typical Isolation: 36 dB (2,000 MHz) Typical Insertion Loss: 1.8 dB (2,000 MHz) Integral ASIC TTL/CMOS Driver Plastic, 50 mil Pitch, SOW-24 Lead, Wide Body Low DC Power Consumption 50 Ohm Nominal Impedance Tape and Reel Packaging Available Test Boards Available Description M/A-COM's SW65-0114 is a GaAs MMIC absorptive SPDT switch with an integral silicon ASIC driver. This device is in a 24-lead plastic package. This switch offers excellent broadband performance and repeatability from DC to 3 GHz, while maintaining low DC power dissipation. The SW65-0114 is ideally suited for wireless infrastructure applications. Also available in ceramic package with improved performance. Package outline conforms to JEDEC standard MS-013AD. Electrical Specifications: TA = 25°C Parameter Test Conditions Units Min Typical Max Insertion Loss DC - 3.0 GHz dB — 1.8 2.2 Isolation (All arms off) DC - 3.0 GHz dB 33 36 — VSWR DC - 3.0 GHz — — 1 On 1.7:1 Off 2.1:1 2.2:1 Trise Tfall Ton Toff Transients 10%/90%, 90%/10% 50% TTL to 90%/10% RF In-band (peak to peak) nS nS mV —— — 15 50 50 50 150 150 1 dB Compression .05 GHz .5 - 3.0 GHz dBm dBm — — +20 +27 — — Input IP3 Two tone inputs 0.05 GHz up to +5 dBm 0.5 - 3.0 GHz dBm dBm — — +35 +46 — — VCC — V +4.5 +5.0 +5.5 VEE — V -8.0 -5.0 -4.75 ICC VCC = +5.0V mA — — 4 IEE VEE = -5.0V mA — — -1 Logic “0” Iin = 20µA max V 0.0 — 0.8 Logic “1” Iin = 20µA max V 2.0 — 5.0 1. Decoupling capacitors (.01 µF) are required on the power supply lines. GaAs SPDT Absorptive Switch with ASIC Driver, DC - 3.0 GHz SW65-0114 V 5.00 Absolute Maximum Ratings 2,3 Pin Configuration Parameter Absolute Maximum Max. Input Power 0.05 GHz 0.5 - 3.0 GHz +27 dBm +34 dBm Bias Voltages VEE VCC Control Voltage 4 -8.5V +5.5V -0.5V to VCC +0.5V Operating Temperature -40°C to +85°C Storage Temperature -65°C to +125°C 2. Operation of this device above any one of these parameters may cause permanent damage. 3. When the RF input is applied to the terminated port, the absolute maximum power is +30 dBm. 4. Standard CMOS TTL interface, latch-up will occur if logic signal is applied prior to power supply. Truth Table Pin # Function Pin # Function 1 RFC 13 C1 2 GND 14 GND 3 GND 15 GND 4 GND 16 GND 5 GND 17 GND 6 RF2 18 GND 7 GND 19 RF1 8 VEE 20 GND 9 GND 21 GND 10 VCC 22 GND 11 GND 23 GND 12 C2 24 GND Ordering Information TTL Control Input RF Common To: Part Number Package C1 C2 RF1 RF2 SW65-0114 Bulk Packaging 1 0 On Off SW65-0114TR Tape and Reel (1K Reel) 0 1 Off On SW65-0114-TB Units Mounted on Test Board Specifications subject to change without notice. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. 2