LTC3873 No RSENSETM Constant Frequency Current Mode Boost/Flyback/SEPIC DC/DC Controller FEATURES DESCRIPTION n The LTC®3873 is a constant frequency current mode, boost, flyback or SEPIC DC/DC controller that drives an N-channel power MOSFET in high input and output voltage converter applications. Soft-start can be programmed using an external capacitor. n n n n n n n n n VIN and VOUT Limited Only by External Components Internal or Programmable External Soft-Start Constant Frequency 200kHz Operation Adjustable Current Limit Current Sense Resistor Optional Maximum 60V on SW Node with RDS(ON) Sensing ±1.5% Voltage Reference Accuracy Current Mode Operation for Excellent Line and Load Transient Response Low Quiescent Current: 300μA Low Profile (1mm) ThinSOTTM and (0.75mm) 2mm × 3mm DFN Package The LTC3873 provides ±1.5% output voltage accuracy and consumes only 300μA quiescent current during normal operation and only 55μA during micropower start-up. Using a 9.3V internal shunt regulator, the LTC3873 can be powered from a high input voltage through a resistor or it can be powered directly from a low impedance DC voltage of 9V or less. The LTC3873 is available in 8-lead ThinSOT and 2mm × 3mm DFN packages. APPLICATIONS n n n PARAMETER VCC UV+ VCC UV– Telecom Power Supplies 42V and 12V Automotive Power Supplies Portable Electronic Equipment LTC3873 8.4V 4V LTC3873-5 3.9V 2.9V L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Efficiency and Power Loss vs Load Current 5V Output Nonisolated Telecom Power Supply • 221k 10μF 10V X5R 7.5k 0.1μF D1 • VCC ITH NGATE LTC3873 RUN/SS GND SW IPRG VFB 12.1k 100μF 6.3V X5R s3 100 VOUT 5V 2A MAX M1 3000 90 EFFICIENCY 80 2500 70 2000 60 50 1500 POWER LOSS 40 1000 30 VIN = 72V VIN = 60V VIN = 48V VIN = 36V 20 10 68mΩ 0 3873 TA01a 500 10 1000 10 38.3k POWER LOSS (mW) 4.7μF 100V X5R 2.2nF D2 T1 EFFICIENCY (%) VIN 36V TO 72V LOAD CURRENT (mA) 3873 TA01b 3873fa 1 LTC3873 ABSOLUTE MAXIMUM RATINGS (Note 1) VCC to GND Low Impedance Source ........................... –0.3V to 9V Current Fed ..........................................25mA Into VCC RUN/SS........................................................ –0.3V to 9V IPRG Voltage.................................–0.3V to (VCC + 0.3V) VFB, ITH Voltages ....................................... –0.3V to 2.4V SW Voltage ................................................ –0.3V to 60V Operating Temperature Range (Note 2).... –40°C to 85°C Junction Temperature (Note 3) ............................. 125°C Storage Temperature Range................... –65°C to 125°C Lead Temperature (Soldering, 10 sec) TS8 Package ..................................................... 300°C PIN CONFIGURATION TOP VIEW TOP VIEW IPRG 1 ITH 2 VFB 3 GND 4 8 SW 7 RUN/SS 6 VCC 5 NGATE 8 VFB 2 7 VCC 6 RUN/SS 5 SW ITH 3 9 IPRG 4 TS8 PACKAGE 8-LEAD PLASTIC TSOT-23 NGATE GND 1 DDB PACKAGE 8-LEAD (3mm s 2mm) PLASTIC DFN TJMAX = 125°C, θJA = 230°C/W TJMAX = 125°C, θJA = 76°C/W EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3873ETS8#PBF LTC3873ETS8\#TRPBF LTCSN 8-Lead Plastic TSOT-23 –40°C to 85°C LTC3873EDDB#PBF LTC3873EDDB#TRPBF LCSK 8-Lead (3mm × 2mm) Plastic DFN –40°C to 85°C LEAD BASED FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3873ETS8 LTC3873ETS8#TR LTCSN 8-Lead Plastic TSOT-23 –40°C to 85°C LTC3873EDDB LTC3873EDDB#TR LCSK 8-Lead (3mm × 2mm) Plastic DFN –40°C to 85°C Consult LTC Marketing for parts specified with wider operating temperature ranges. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3873fa 2 LTC3873 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 9V unless otherwise noted. (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS Input DC Supply Current Normal Operation Shutdown UVLO Typicals VITH = 1.9V VRUN/SS = 0V VCC = UVLO Threshold – 100mV, VRUN/SS = VCC 300 55 45 400 100 60 μA μA μA Undervoltage Lockout Threshold VCC Rising VCC Falling VCC Hysteresis l l l 7.9 3.5 4.0 8.4 4.0 4.4 8.8 4.4 4.8 V V V Shutdown Threshold (at RUN/SS) VRUN/SS Falling VRUN/SS Rising l 0.5 0.6 0.7 0.8 0.9 1.0 V V Regulated Feedback Voltage (Note 5) l 1.182 1.2 1.218 V Feedback Voltage Line Regulation 5.6V < VCC < 9V (Note 5) 0.12 mV/V Feedback Voltage Load Regulation VITH = 1.6V (Note 5) VITH = 1V (Note 5) 0.05 –0.05 % % VFB Input Current (Note 5) Maximum Duty Cycle RUN/SS Pull-Up Current VRUN/SS = 0V VRUN/SS = 1.3V 25 50 nA 70 78 84 % 1.5 5 3 15 4.5 25 μA μA ISLMAX, Peak Slope Compensation Current 20 Oscillator Frequency 160 200 μA 240 Gate Drive Rise Time CLOAD = 3000pF (Note 6) Gate Drive Fall Time CLOAD = 3000pF (Note 6) Peak Current Sense Voltage IPRG = GND IPRG = Float IPRG = VIN l l l 95 165 265 110 185 295 125 210 325 mV mV mV VIN Shunt Regulator Voltage IIN = 1mA, IIN = 25mA, VRUN/SS = 0V l 9 9.3 9.6 V Default Internal Soft-Start Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3873E is guaranteed to meet performance specifications from 0°C to 85°C junction temperature. Specifications over the –40°C to 85°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: TJ = TA + (PD • θJA) 40 kHz ns 40 3.3 ns ms Note 4: The dynamic input supply current is higher due to power MOSFET gate charging (QG • fOSC). See Applications Information. Note 5: The LTC3873 is tested in a feedback loop which servos VFB to the reference voltage with the ITH pin forced to the midpoint of its voltage range (0.7V ≤ VITH ≤ 1.9V, midpoint = 1.3V). Note 6: Rise and fall times are measured at 10% and 90% levels. VCC = 5.6V. 3873fa 3 LTC3873 TYPICAL PERFORMANCE CHARACTERISTICS Feedback Voltage vs Temperature Feedback Voltage Line Regulation 1.25 1.2025 1.24 1.2020 1.23 1.2015 ITH Voltage vs RUN/SS Voltage 2.5 VIN = 5V 1.22 1.21 ITH VOLTAGE (V) VFB VOLTAGE (V) VFB VOLTAGE (V) 2.0 1.2010 1.2005 1.20 1.2000 1.19 1.1995 1.5 1.0 0.5 1.18 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 1.1990 6 5 7 3873 G03 Gate Drive Rise and Fall Time vs CLOAD Shutdown IQ vs Temperature 70 100 80 65 90 70 50 45 40 35 30 80 60 70 50 TIME (ns) SHUTDOWN MODE IQ (μA) 55 40 30 20 3 4 7 6 VIN (V) 5 8 9 10 RISE TIME 60 FALL TIME 50 40 30 20 20 10 25 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 RUN/SS VOLTAGE (V) 3873 G02 Shutdown Mode IQ vs VIN 60 0 VIN (V) 3873 G01 SHUTDOWN MODE IQ (μA) 0 10 9 8 10 0 –60 –40 –20 0 0 20 40 60 80 100 120 TEMPERATURE (°C) 3873 G04 0 2000 6000 4000 CLOAD (pF) 8000 10000 3873 G06 3873 G05 Shunt Regulation Voltage vs ISHUNT RUN Threshold vs Temperature 1.0 10.2 10.1 0.8 0.7 REGULATION VOLTAGE (V) RUN THRESHOLDS (V) 0.9 RISING FALLING 0.6 10.0 9.9 9.8 9.7 9.6 9.5 9.4 9.3 0.5 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 3873 G07 9.2 0 5 10 15 20 25 30 ISHUNT (mA) 35 40 45 3873 G08 3873fa 4 LTC3873 TYPICAL PERFORMANCE CHARACTERISTICS Maximum Sense Threshold vs Temperature Frequency vs Temperature 300 MAXIMUM SENSE THRESHOLD (mV) 250 FREQUECY (kHz) 230 210 190 170 150 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 3873 G09 PIN FUNCTIONS IPRG = VIN 250 200 IPRG = FLOAT 150 IPRG = GND 100 50 0 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 3873 G10 (TS8/DDB) IPRG (Pin 1/Pin 4): Current Sense Limit Select Pin. ITH (Pin 2/Pin 3): This pin serves as the error amplifier compensation point. Nominal voltage range for this pin is 0.7V to 1.9V. VFB (Pin 3/Pin 2): This pin receives the feedback voltage from an external resistor divider across the output. GND (Pin 4/Pin 1): Ground Pin. NGATE (Pin 5/Pin 8): Gate Drive for the External N-Channel MOSFET. This pin swings from 0V to VIN. RUN/SS (Pin 7/Pin 6): Shutdown and External Soft-Start Pin. In shutdown, all functions are disabled and the NGATE pin is held low. SW (Pin 8/Pin 5): Switch node connection to inductor and current sense input pin through external slope compensation resistor. Normally, the external N-channel MOSFET’s drain is connected to this pin. Exposed Pad (NA/Pin 9): Ground. Must be soldered to PCB for electrical contact and rated thermal performance. VCC (Pin 6/Pin 7): Supply Pin. This pin must be closely decoupled to GND (Pin 4). 3873fa 5 LTC3873 FUNCTIONAL DIAGRAM GND VCC UV UNDERVOLTAGE LOCKOUT VOLTAGE REFERENCE 1.2V SW VCC 9.5V SHUNT REGULATOR SLOPE COMPENSATION SHUTDOWN COMPARATOR – + IPRG CURRENT COMPARATOR 3μA ILIM + SHDN ITH BUFFER RUN/SS RS LATCH – R S Q CURRENT LIMIT CLAMP VIN SWITCHING LOGIC CIRCUIT INTERNAL SOFT-START RAMP NGATE VFB – ERROR AMPLIFIER 200kHz OSCILLATOR AND MAX DUTY CYCLE 1.2V + ITH 3873 FD 3873fa 6 LTC3873 OPERATION Main Control Loop The LTC3873 is a general purpose N-channel switching DC/DC converter for boost, flyback and SEPIC applications. Its No RSENSE sensing technique improves efficiency, increases power density and reduces the cost of the overall solution. For circuit operation, please refer to the Functional Diagram of the IC and the Typical Application on the front page. During normal operation, the power MOSFET is turned on when the oscillator sets the PWM latch and is turned off when the current comparator resets the latch. The divided-down output voltage is compared to an internal 1.2V reference by the error amplifier, which outputs an error signal at the ITH pin. The voltage on the ITH pin sets the current comparator input threshold. When the load current increases, a fall in the VFB voltage relative to the reference voltage causes the ITH pin to rise, causing the current comparator to trip at a higher peak inductor current value. The average inductor current will therefore rise until it equals the load current, thereby maintaining output regulation. L D VIN VOUT VCC + SW COUT VSW LTC3873 The LTC3873 can be used either by sensing the voltage drop across the power MOSFET or by connecting the SW pin to a conventional sensing resistor in the source of the power MOSFET. Sensing the voltage across the power MOSFET maximizes converter efficiency and minimizes the component count; the maximum rating for this pin, 60V, allows MOSFET sensing in a wide output voltage range. Shunt Regulator A built-in shunt regulator from the VCC pin to GND limits the voltage on the VCC pin to approximately 9.3V as long as the shunt regulator is not forced to sink more than 25mA. The shunt regulator permits the use of a wide variety of powering schemes that exceed the LTC3873’s absolute maximum ratings. Further details on powering schemes are described in the Application Information section. Start-Up/Shutdown The LTC3873 has two shutdown mechanisms to disable and enable operation: an undervoltage lockout on the VCC supply pin voltage and a threshold RUN/SS pin. The LTC3873 transitions into and out of shutdown according to the state diagram shown in Figure 3. The undervoltage lockout (UVLO) mechanism prevents the LTC3873 from trying to drive a MOSFET with insufficient voltage. The voltage at the VCC pin must exceed VTURNON NGATE GND GND 3873 F01 LTC3873 SHUT DOWN Figure 1. SW Pin (Internal Sense Pin) Connection for Maximum Efficiency L D VIN VOUT VSW VCC VIN < VTURNOFF (NOMINALLY 4V) VRUN/SS < VSHDN (NOMINALLY 0.8V) VRUN/SS > VSHDN AND VIN > VTURNON (NOMINALLY 8.4V) + NGATE COUT LTC3873 SW GND RSENSE LTC3873 ENABLED GND 3873 F02 Figure 2. SW Pin (Internal Sense Pin) Connection for Sensing Resistor 3873 F03 Figure 3. Start-Up/Shutdown State Diagram 3873fa 7 LTC3873 OPERATION (nominally 8.4V) at least momentarily to enable LTC3873 operation. The VCC voltage is then allowed to fall to VTURNOFF (nominally 4V) before undervoltage lockout disables the LTC3873. This wide UVLO hysteresis range supports the use of trickle charger on the flyback transformer to power the LTC3873—see the section, VCC Bias Power. The RUN/SS pin can be driven below VSHDN (nominally 0.7V) to force the LTC3873 into shutdwn. When the chip is off, the input supply current is typically only 55μA. Soft-Start MAXIMUM CURRENT SENSE VOLTAGE (mV) Leave the RUN/SS pin open to use the internal 3.3ms soft-start. During the internal soft-start, a voltage ramp limits the VITH. 3.3ms is required for ITH to ramp from zero current level to full current level. The soft-start can be lengthened by placing an external capacitor from the RUN/SS pin to the GND. A 3μA current will charge the capacitor, pulling the RUN/SS pin above the shutdown threshold and a 15μA pull-up current will continue to ramp RUN/SS to limit VITH during the start-up. When RUN/SS is driven by an external logic, a minimum of 2.75V logic is recommended to allow the maximum ITH range. Light Load Operation Under very light load current conditions, the ITH pin voltage will be very close to the zero current level of 0.85V. As the load current decreases further, an internal offset at the current comparator input will assure that the current comparator remains tripped (even at zero load current) and the regulator will start to skip cycles in order to maintain regulation. This behavior allows the regulator to maintain constant frequency down to very light loads, resulting in low output ripple as well as low audible noise and reduced RF interference while providing high light load efficiency. Current Sense During the switch on-time, the control circuit limits the maximum voltage drop across the current sense component to about 295mV, 110mV and 185mV at low duty cycle with IPRG tied to VIN, GND or left floating respectively. It is reduced with increasing duty cycle as shown in Figure 4. 300 250 IPRG = HIGH 200 IPRG = FLOAT 150 IPRG = LOW 100 50 0 1 20 40 60 DUTY CYCLE (%) 80 100 3873 F04 Figure 4. Maximum SENSE Threshold Voltage vs Duty Cycle 3873fa 8 LTC3873 APPLICATIONS INFORMATION VCC Bias Power The VCC pin must be bypassed to the GND pin with a minimum 10μF ceramic or tantalum capacitor located immediately adjacent to the two pins. Proper supply bypassing is necessary to supply the high transient currents required by the MOSFET gate driver. For maximum flexibility, the LTC3873 is designed so that it can be operated from voltages well beyond the LTC3873’s absolute maximum ratings. In the simplest case, the LTC3873 can be powered with a resistor connected between the input voltage and VCC. The built-in shunt regulator limits the voltage on the VCC pin to around 9.3V as long as the shunt regulator is not forced to sink more than 25mA. This powering scheme has the drawback that the power loss in the resistor reduces converter efficiency and the 25mA shunt regulator maximum may limit the maximum-minimum range of input voltage. In some cases, the input or the output voltage is within the operational range of VCC for the LTC3873. In this case, the LTC3873 is operated directly from either the input or output voltage. The typical application circuit on the first page of this data sheet shows a 5V output converter in which RSTART and CVCC form a start-up trickle charger while D1 powers VCC from the output once the converter is in normal operation. Note that RSTART need only supply the very small 55μA micropower start-up current while CVCC is charged to VTURNON. At this point, VRUN/SS > VSHDN, the converter begins switching the external MOSFET and ramps up the converter output voltage at a rate set by the capacitor CRUN/SS on the RUN/SS pin. Since RSTART cannot supply enough current to operate the external MOSFET, CVCC begins discharging and VCC drops. The soft-start must be fast enough so that the output voltage reaches its target value of 5V before VCC drops to VTURNOFF or the converter will fail to start. Otherwise more CVCC capacitor is needed to hold the input voltage when soft-start is too long. Figure 5 shows a different flyback converter bias power strategy for a case in which neither the input or the output is suitable for providing the bias power to the LTC3873. The trickle charger is identical to that described in the prior paragraph. However, the flyback transformer has an additional bias winding to provide bias power. Note that this topology is very powerful because, by appropriate choice of the transformer turn ratio, the output voltage can be chosen without regard to the value of the input voltage or the VCC bias power for the LTC3873. The number of the turns in the bias winding is chosen according to: NBIAS = NSEC VCC + VD2 VOUT + VD1 where NBIAS is the number of turns in the bias winding, NSEC is the number of turns in the secondary winding, VCC is the desired voltage to power the LTC3873, VOUT is the converter output voltage, VD1 is the forward drop voltage of D1 and VD2 is the forward drop voltage of D2. Note that since VOUT is regulated by the converter control loop, VCC is also regulated although not precisely. The value of VCC is often constrained since NBIAS and NSEC are often a limited range of small integer numbers. For proper operation, the value of VCC must be between VTURNON and VTURNOFF . Since the ratio of VTURNON to VTURNOFF is over two to one, the requirement is relative easy to satisfy. Finally, as with all trickle charger start-up schemes, the soft-start must be fast enough so that the power supplied by the bias winding is available before the discharge of CVCC down to VTURNOFF . T1 NBIAS D2 • VIN D1 VOUT RSTART R3 • CIN NPRI NSEC COUT • CVCC VCC RUN/SS NGATE CVIN Q1 LTC3873 ITH RSL CC SW GND RSENSE VFB R1 R2 3873 F05 Figure 5. Typical LTC3873 Application Circuit 3873fa 9 LTC3873 APPLICATIONS INFORMATION The circuit in Figure 6 shows a third way to power the LTC3873. An external series pre-regulator consisting of series pass transistor Q1, zener diode D1 and bias resistor RB brings VCC to at least 7.6V nominal, well above the maximum rated VCC turn-off threshold of 4V. Resistor RSTART momentarily charges the VCC node up to the VCC turn-on threshold, enabling the LTC3873. VIN RB Q1 RSTART LTC3873 VCC D1 8.2V CVCC 0.1μF GND 3873 F06 Figure 6 Slope Compensation The LTC3873 has built-in internal slope compensation to stabilize the control loop against sub-harmonic oscillation. It also provides the ability to externally increase slope compensation by injecting a ramping current out of its SW pin into an external slope compensation resistor (RSL in Figure 5). This current ramp starts at zero right after the NGATE pin has been set high. The current rises linearly towards a peak of 20μA at the maximum duty cycle of 80%, shutting off once the NGATE pin goes low. A series resistor (RSL) connecting the SW pin to the current sense resistor (RSENSE) thus develops a ramping voltage drop. From the perspective of the SW pin, this ramping voltage adds to the voltage across the sense resistor, effectively reducing the current comparator threshold in proportion to duty cycle. The amount of reduction in the current comparator threshold (ΔVSENSE) can be calculated using the following equation: ΔVSENSE = Duty Cycle – 6% 20μA • RSLOPE 80% Note the external programmable slope compensation is only needed when the internal slope compensation is not sufficient. In most applications RSL can be shorted. For the LTC3873, when the RDS(ON) sensing technique is used, the ringing on the SW pin disrupts the tiny slope compensation current out of the pin. It is not recommended to add external slope compensation in this case. Output Voltage Programming The output voltage is set by a resistor divider according to the following formula: ⎛ R2⎞ VO = 1.2V • ⎜1+ ⎟ ⎝ R1⎠ The external resistor divider is connected to the output as shown in Figure 5, allowing remote voltage sensing. Choose resistance values for R1 and R2 to be as large as possible in order to minimize any efficiency loss due to the static current drawn from VOUT, but just small enough so that when VOUT is in regulation, the error caused by the nonzero input current to the VFB pin is less than 1%. A good rule of thumb is to choose R1 to be 24k or less. Transformer Design Considerations Transformer specification and design is perhaps the most critical part of applying the LTC3873 successfully. In addition to the usual list of caveats dealing with high frequency power transformer design, the following should prove useful. Turns Ratios Due to the use of the external feedback resistor divider ratio to set output voltage, the user has relative freedom in selecting a transformer turns ratio to suit a given application. Simple ratios of small integers, e.g., 1:1, 2:1, 3:2, etc. can be employed which yield more freedom in setting total turns and mutual inductance. Simple integer turns ratios also facilitate the use of “off-the-shelf” configurable transformers such as the Coiltronics VERSA-PAC series in applications with high input-to-output voltage ratios. For example, if a 6-winding VERSA-PAC is used with three windings in series on the primary and three windings in parallel on the secondary, a 3:1 turns ratio will be achieved. Turns ratio can be chosen on the basis of desired duty cycle. However, remember that the input supply voltage 3873fa 10 LTC3873 APPLICATIONS INFORMATION plus the secondary-to-primary referred voltage of the flyback pulse (including leakage spike) must not exceed the allowed external MOSFET breakdown rating. Leakage Inductance Transformer leakage inductance (on either the primary or secondary) causes a voltage spike to occur after the output switch (Q1) turn-off. This is increasingly prominent at higher load currents where more stored energy must be dissipated. In some cases a “snubber” circuit will be required to avoid overvoltage breakdown at the MOSFET’s drain node. Application Note 19 is a good reference on snubber design. A bifilar or similar winding technique is a good way to minimize troublesome leakage inductances. However, remember that this will limit the primary-tosecondary breakdown voltage, so bifilar winding is not always practical. Output Capacitors The output capacitor is normally chosen by its effective series resistance (ESR), which determines output ripple voltage and affects efficiency. Low ESR ceramic capacitors are often used to minimize the output ripple. Boost regulators have large RMS ripple current in the output capacitor that must be rated to handle the current. The output ripple current (RMS) is: IRMS(COUT ) ≈ IOUT(MAX ) • The power MOSFET serves two purposes in the LTC3873: it represents the main switching element in the power path and its RDS(ON) represents the current sensing element for the control loop. Important parameters for the power MOSFET include the drain-to-source breakdown voltage (BVDSS), the threshold voltage (VGS(TH)), the on-resistance (RDS(ON)) versus gate-to-source voltage, the gate-to-source and gate-to-drain charges (QGS and QGD, respectively), the maximum drain current (ID(MAX)) and the MOSFET’s thermal resistances (RTH(JC) and RTH(JA)). For boost applications with RDS(ON) sensing, refer to the LTC3872 data sheet for the selection of MOSFET RDS(ON). (I2R) and switching MOSFETs have conduction losses losses. For VDS < 20V, high current efficiency generally improves with large MOSFETs with low RDS(ON), while for VDS > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower reverse transfer capacitance, CRSS, actually provides higher efficiency. VIN(MIN) Output ripple is then simply: VOUT = RESR(ΔIL(RMS)) The output capacitor for flyback converter should have a ripple current rating greater than: IRMS = IOUT • Power MOSFET Selection VOUT – VIN(MIN) DMAX 1 – DMAX Input Capacitors The input capacitor of a boost converter is less critical due to the fact that the input current waveform is triangular, and does not contain large square wave currents as found in the output capacitor. The input voltage source impedance determines the size of the capacitor that is typically 10μF to 100μF. A low ESR is recommended although not as critical as the output capacitor can be on the order of 0.3Ω. The RMS input ripple current for a boost converter is: IRMS(CIN) = 0.3 • VIN(MIN) L•f • DMAX Please note that the input capacitor can see a very high surge current when a battery is suddenly connected to the input of the converter and solid tantalum capacitors can fail catastrophically under these conditions. 3873fa 11 LTC3873 APPLICATIONS INFORMATION In a flyback converter, the input flows in pulses placing severe demands on the input capacitors. Select an input capacitor with a ripple current rating greater than: IRMS = PIN VIN(MIN) 1 – DMAX DMAX impacted by duty factor. Unfortunately duty factor cannot be adjusted to simultaneously optimize all of these requirements. In general, avoid extreme duty factors since this severely impacts the current stress on most of the components. A reasonable target for duty factor is 50% at nominal input voltage. Using this rule of thumb, the ideal transformer turns ratio is: Duty Cycle Considerations The LTC3873 imposes a maximum duty cycle limit of 80% typical. For a flyback converter, the maximum duty cycle prevents the transformer core from saturation. In a boost converter application, however, it sets a limit on the maximum step-up ratio or maximum output voltage with the given input voltage of: VOUT(MAX ) = VIN(MIN) 1 – 0.8 – VD Current and voltage stress on the power switch and synchronous rectifiers, input and output capacitor RMS currents and transformer utilization (size vs power) are VIN 36V TO 72V 15k ITH NGATE LTC3873 GND VCC 0.1μF RUN/SS VOUT 1 – D VOUT • = VIN D VIN Output Diode Selection To maximize efficiency, a fast switching diode with low forward drop and low reverse leakage is desired. The output diode in a boost converter conducts current during the switch off-time. The peak reverse voltage that the diode must withstand is equal to the regulator output voltage. The average forward current in normal operation is equal to the output current, and the peak current is equal to the peak inductor current. T1 • 4.7μF 100V 221k 2.2nF NIDEAL = • D2 UPS840 100μF 6.3V s3 VOUT* 3.3V 3A Q1 FAN2512 • D1 BAS516 51Ω 0.1μF IPRG 12.06k VFB = 1.2V SW RFB* 21.5k VOUT 3873 F07 4.7μF 10V 68mΩ *FOR 5V OUTPUT CHANGE RFB TO 42.2k Figure 7. 3.3V Output Nonisolated Telecom DC/DC Converter 3873fa 12 LTC3873 TYPICAL APPLICATIONS 9V to 15V VIN, 12V VOUT SEPIC Converter T1 4.56μH BH510-1009 BH ELECTRONICS 4 1 VIN 9V TO 15V 10μF s3 + 100μF 20V 2 • • 3 10μF 25V 301Ω UPS840 + LTC3873 100k 1 2 3 10nF 4 33.2k 11k IPRG ITH SW RUN/SS VFB = 1.2V VCC GND NGATE Si4840 8 47μF 16V s3 10μF 16V VOUT 12V 2A 7 6 5 4.7μF 0.1μF 3873 TA05 10W Isolated Telecom Converter TR1 ISOLATION BARRIER VIN 36V TO 72V 4.7μF 100V 221k OPT 221k MMBTA42 OPT PDZ6.8B OPT BAS516 2 3 4 IRPG ISENSE ITH RUN/SS FB GND VCC GATE • VOUT 3.3V 3A 7 8 100μF 6.3V s3 51Ω 5• 2 FDC2512 LTC3873 1 4• 1 9 10 UPS840 2.2Ω 2 1 8 BAT54CWT1G 7 0.068Ω 6 3 5 1μF OPT 4.7μF 1210 AND 0805 0.1μF 6.8k 274Ω 4 NEC PS2801-1 1 3 2 BAT760 BAS516 LT4430 1 2 3 VIN OPTO GND COMP OC 0.6V FB 1μF 6 5 4 22nF 330pF 100k 3.01k 22.1k 3873 TA04 2200pF 250V AC 3873fa 13 LTC3873 PACKAGE DESCRIPTION TS8 Package 8-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1637) 0.52 MAX 2.90 BSC (NOTE 4) 0.65 REF 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 – 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.22 – 0.36 8 PLCS (NOTE 3) 0.65 BSC 0.80 – 0.90 0.20 BSC 0.01 – 0.10 1.00 MAX DATUM ‘A’ 0.30 – 0.50 REF 0.09 – 0.20 (NOTE 3) 1.95 BSC TS8 TSOT-23 0802 NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 3873fa 14 LTC3873 PACKAGE DESCRIPTION DDB Package 8-Lead Plastic DFN (3mm × 2mm) (Reference LTC DWG # 05-08-1702 Rev B) 0.61 p0.05 (2 SIDES) 0.70 p0.05 2.55 p0.05 1.15 p0.05 PACKAGE OUTLINE 0.25 p 0.05 0.50 BSC 2.20 p0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 p0.10 (2 SIDES) R = 0.115 TYP 5 R = 0.05 TYP 0.40 p 0.10 8 2.00 p0.10 (2 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6) 0.56 p 0.05 (2 SIDES) 0.200 REF 0.75 p0.05 0 – 0.05 4 0.25 p 0.05 1 PIN 1 R = 0.20 OR 0.25 s 45o CHAMFER (DDB8) DFN 0905 REV B 0.50 BSC 2.15 p0.05 (2 SIDES) BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO VERSION (WECD-1) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3873fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC3873 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT 1619 Current Mode PWM Controller 300kHz Fixed Frequency, Boost, SEPIC, Flyback Topology LTC1624 Current Mode DC/DC Controller SO-8; 300kHz Operating Frequency; Buck, Boost, SEPIC Design; VIN Up to 36V LTC1700 No RSENSE Synchronous Step-Up Controller Up to 95% Efficiency, Operating as Low as 0.9V Input LTC1871-7 Wide Input Range Controller No RSENSE, 7V Gate Drive, Current Mode Control LTC1872/LTC1872B SOT-23 Boost Controller Delievers Up to 5A, 550kHz Fixed Frequency, Current Mode LT1930 1.2MHz, SOT-23 Boost Converter Up to 34V Output, 2.6V VIN 16V, Miniature Design LT1931 Inverting 1.2MHz, SOT-23 Converter Positive-to Negative DC/DC Conversion, Miniature Design LTC3401/LTC3402 1A/2A 3MHz Synchronous Boost Converters Up to 97% Efficiency, Very Small Solution, 0.5V ≤ VIN ≤ 5V LTC3704 Positive-to Negative DC/DC Controller No RSENSE, Current Mode Control, 50kHz to 1MHz LTC1871/LTC1871-7 No RSENSE, Wide Input Range DC/DC Boost Controller No RSENSE, Current Mode Control, 2.5V ≤ VIN ≤ 36V LTC3703/LTC3703-5 100V Synchronous Controller Step-Up or Step Down, 600kHz, SSOP-16, SSOP-28 LTC3803/LTC3803-5 200kHz Flyback DC/DC Controller VIN and VOUT Limited Only by External Components LTC3805 Adjustable Frequency Flyback Controller VIN and VOUT Limited Only by External Components LT3825 Isolated No-Opto Synchronous Flyback Controller VIN: 24V to 75V, Up to 80W, Current Mode Control LT3837 Isolated No-Opto Synchronous Flyback Controller VIN: 4.5V to 20V, Up to 60W, Current Mode Control ® LTC3872 No RSENSE Boost Controller 550kHz Fixed Frequency, ThinSOT or DFN, 2.75V ≤ VIN ≤ 9.8V LTC3873 No RSENSE Constant Frequency Boost/Flyback/SEPIC Controller VIN and VOUT Limited Only by External Components, 200kHz Frequency, ThinSOT or DFN Package 3873fa 16 Linear Technology Corporation LT 0708 REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007