May 2009 TLI4906 High Precision Hall Effect Switches for Industrial and Consumer Applications TLI4906K, TLI4906L Datasheet R e v. 1 . 0 Sense and Control Edition 2009-05-04 Published by Infineon Technologies AG 81726 Munich, Germany © 2009 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. TLI4906 High Precision Hall Effect Switches for Industrial and Consumer Applications Revision History: 2009-05-04, Rev. 1.0 Previous Revisions: none Page Subjects (major changes since last revision) We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] Datasheet 3 Rev. 1.0, 2009-05-04 TLI4906 Table of Contents Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1 1.1 1.2 1.3 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Target Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 2.2 2.3 2.4 2.5 2.6 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Operating Modes and States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Functional Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 3.1 3.2 3.3 3.4 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4.1 4.2 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 TLI4906K Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 TLI4906L Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Datasheet 4 7 7 7 7 11 11 11 12 12 Rev. 1.0, 2009-05-04 TLI4906 List of Figures List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Datasheet Pin Configuration and sensitive area (Top view, figure not to scale) . . . . . . . . . . . . . . . . . . . . . . . . 8 TLI4906x Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Definition of the Magnetic Field direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Output Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Marking of the TLI4906K and distance of the chip to the upper side . . . . . . . . . . . . . . . . . . . . . . . 14 PG-SC59-3-4 Package Outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Footprint PG-SC59-3-4 (SOT23 compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Marking of the TLI4906L and distance of the chip to the upper side . . . . . . . . . . . . . . . . . . . . . . . 15 PG-SSO-3-2 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5 Rev. 1.0, 2009-05-04 TLI4906 List of Tables List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Datasheet PIN Definitions for the PG-SC59-3-4 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PIN Definitions for the PG-SSO-3-2 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Magnetic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Rev. 1.0, 2009-05-04 High Precision Hall Effect Switch 1 Product Description 1.1 Overview TLI4906 The TLI4906x is a high precision Hall Effect Switch with highly accurate switching thresholds for ambient operating temperatures up to 125°C. The TLI4906K is available in a PG-SC59-3-4 package, the TLI4906L in a PG-SSO-3-2 package. 1.2 • • • • • • • • • • Features 2.7 V to 18 V supply voltage operation. Operation from unregulated power supply. High sensitivity and high stability of the magnetic switching points. High resistance to mechanical stress by active error compensation. Reverse battery protection (-18 V). Superior temperature stability. Low jitter (typically 1 µs). High ESD performance (± 4 kV HBM). Digital output signal (open-drain). Not suitable for automotive applications 1.3 Target Applications The TLI4906x is ideally suited for all industrial and consumer applications that require a high precision switching thresholds for position sensing. It can be used for example for: security systems, alignment control, push buttons, keyboards, key switches, machine tools, etc. Product Name Product Type Ordering Code Package Hall Effect Switch TLI4906K SP000604306 PG-SC59-3-4 Hall Effect Switch TLI4906L SP000604320 PG-SSO-3-2 Datasheet 7 Rev. 1.0, 2009-05-04 TLI4906 Functional Description 2 Functional Description 2.1 General Precise magnetic switching thresholds and high temperature stability are achieved by active compensation circuits and chopper techniques on chip. Offset voltages generated by temperature-induced stress or overmolding are canceled so that high accuracy is achieved. The IC has an open collector output stage with 20 mA current sink capability. A wide operating voltage range from 2.7 V to 18 V with reverse polarity protection down to -18 V makes the TLI4906xsuitable for a wide range of applications. A magnetic south pole with a field strength above Bop turns the output on. A magnetic north pole exceeding Brp turns it off. 2.2 Pin Configuration Center of Sensitive Area 2.08 ± 0.1 3 1.35 0.8 1 1.5 ± 0.15 2 ± 0.15 1 2 3 PG-SSO-3-2 SC59 Figure 1 Datasheet ± 0.1 Pin Configuration and sensitive area (Top view, figure not to scale) 8 Rev. 1.0, 2009-05-04 TLI4906 Functional Description 2.3 Pin Description Table 1 PIN Definitions for the PG-SC59-3-4 package PIN No. Name Function 1 Vs Supply Voltage 2 Q Output 3 GND Ground Table 2 PIN Definitions for the PG-SSO-3-2 package PIN No. Name Function 1 Vs Supply Voltage 2 GND Ground 3 Q Output 2.4 Block Diagram VS Voltage Regulator reverse polarity protected Bias and Compensation Circuits Oscillator and Sequencer Q Ref Amplifier Chopped Hall Probe Figure 2 Datasheet Low Pass Filter Comparator with Hysteresis GND TLI4906x Block Diagram 9 Rev. 1.0, 2009-05-04 TLI4906 Functional Description 2.5 Operating Modes and States Field Direction and Definition Positive magnetic fields correspond to the south pole of the magnet targeting the branded side of the package. N N S S Branded Side Branded Side Figure 3 Definition of the Magnetic Field direction VQ B 0 Figure 4 Output Signal 2.6 Functional Block Description Brp Bop The chopped Hall Effect Switch comprises a Hall probe, a bias generator, compensation circuits, an oscillator and an output transistor. The bias generator provides currents to the Hall probe and the active circuits. Compensation circuits stabilize response of the IC over temperature and reduce the impact of process variations. The Active Error Compensation rejects offsets in the signal path and reduces the impact of mechanical stress in the package caused by molding, soldering and thermal effects. The chopper technique together with the threshold generator and the comparator ensure high accurate magnetic switching points. Datasheet 10 Rev. 1.0, 2009-05-04 TLI4906 Specification 3 Specification 3.1 Application circuit Figure 5 GND VS 1.2kΩ 4.7nF Q 4.7nF TLI4906X Q GND 200Ω VS Application circuit It is recommended to use a resistor of 200 Ω in the supply line for current limitation in the case of an overvoltage pulse. Two capacitors of 4.7 nF enhance the EMC performance. The pull-up of 1.2 kΩ limits the current through the output transistor. 3.2 Absolute Maximum Ratings Stress above the maximum values listed in this section may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect the reliability of the device. Exceeding only one of these values may cause irreversible damage to the device. Table 3 Absolute Maximum Ratings Parameter Symbol Values Min. Typ. Max. Unit Maximum Ambient Temperature TA - 40 – 125 °C Maximum Junction Temperature TJ - 40 – 150 °C Supply Voltage VS - 18 – 18 V -50 – 50 mA Supply current through protection IS device Output Voltage VOUT - 0.7 – 18 V Storage Temperature TS - 40 – 150 °C Magnetic flux density B – – unlimited mT ESD Robustness HBM: 1.5 kΩ, 100 pF VESD,HBM1) – – 4 kV Note / Test Condition 1) According to EIA/JESD22-A114-E Datasheet 11 Rev. 1.0, 2009-05-04 TLI4906 Specification 3.3 Operating Range The following operating conditions must not be exceeded in order to ensure correct operation of the TLI4906x. All parameters specified in the following sections refer to these operating conditions unless otherwise mentioned. Table 4 Operating Range Parameter Symbol Values Unit Min. Typ. Max. Supply Voltage VS 2.7 – 18 V Output Voltage VQ -0.7 – 18 V Output Current IQ 0 – 20 mA Maximum Ambient Temperature TA -40 – 125 °C 3.4 Note / Test Condition Electrical Characteristics Product characteristics include the spread of values guaranteed within the specified voltage and ambient temperature range. typical characteristics are the median of the production (at Vs=12V and TA=25°C). Table 5 Electrical Characteristics Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition Supply Current IS 2 4 6 mA VS=2.7 V...18 V Reverse Current ISR 0 0.2 1 mA VS=-18 V Output Saturation Voltage VQSAT – 0.3 0.6 V IQ=20 mA Output leakage current IQLEAK – 0.05 10 µA VQ=18 V tf – 0.02 1 µs RL=1.2k Ω, CL=50 pF tr – 0.4 1 µs fOSC – 320 – 1) Output fall time Output rise time 1) Chopper frequency kHz 2) fSW 0 – 15 kHz td – 13 – µs Output jitter tQJ – 1 – µsRMS Typical value for a 1 kHz square wave signal Power-on Time5) tPON – 13 – µs VS > 2.7 V Thermal Resistance junction to ambient6) Rthja – 100 – K/W TLI4906K 190 K/W TLI4906L Switching frequency Delay time 3) 4) – 1) See Figure 6 2) To operate the sensor at maximum switching frequency, the value of the magnetic signal amplitude must be 1.4 times higher than the static fields. This is due to the -3 dB corner frequency of the low pass filter in the signal path. 3) Systematic delay between magnetic threshold reached and output. 4) Jitter is the unpredictable deviation of the output switching delay. 5) Time from applying VS. > 2.7 V to the sensor until the output state is valid. 6)Relationship between junction and ambient temperature: TJ=Tamb + Rthja . (VS . IS + VQS . IQ). Datasheet 12 Rev. 1.0, 2009-05-04 TLI4906 Specification B OP Applied Magnetic Field B RP td td tf VQ tr 90% 10% Figure 6 Timing Diagram Table 6 Magnetic Characteristics 1) Parameter Symbol Values Min. Typ. Max. Unit Operate point BOP 6.2 10.0 13.9 mT Release point BRP 4.7 8.5 12.3 mT Hysteresis BHYS 0.7 1.5 3.0 mT Temperature compensation of magnetic thresholds TC – -350 – ppm/°C Repeatability of magnetic thresholds3) BREP – 20 – µTRMS Note / Test Condition 2) typical value for ∆Β/∆t > 12mT/ms 1) Over all operating conditions. 2) At 25°C. 3) BREP is equivalent to the noise constant. Datasheet 13 Rev. 1.0, 2009-05-04 TLI4906 Package Information 4 Package Information 4.1 TLI4906K Package Outline Year (y) = 0...9 Month (m) = 1...9, O - October N - November D - December d I06 ym Branded Side d: Distance chip to upper side of IC: d = 0.56 ±0.1 mm AEA03244 Figure 7 Marking of the TLI4906K and distance of the chip to the upper side 1.1 ±0.1 3 ±0.1 0.2 0.1 M +0.1 1.6 +0.15 -0.3 2.8 +0.2 -0.1 3 1 0.15 MAX. 0.45 ±0.15 3x0.4 0.1 +0.05 -0.1 2 0.1 M 0.95 0.95 (0.55) +0.1 0.15 -0. 05 0˚...8˚ MAX. GPS09473 Figure 8 Datasheet PG-SC59-3-4 Package Outline 14 Rev. 1.0, 2009-05-04 TLI4906 Package Information 0.8 1.4 min 0.9 1.6 1.3 0.9 1.4 min 0.8 1.2 0.8 1.2 0.8 Reflow Soldering Wave Soldering Footprint PG-SC59-3-4 (SOT23 compatible) 4.2 TLI4906L Package Outline I06 yww S Figure 9 Figure 10 Datasheet Year (y) = 0...9 Calendar Week (ww) = 01...52 Marking of the TLI4906L and distance of the chip to the upper side 15 Rev. 1.0, 2009-05-04 TLI4906 Package Information 0.8 ±0.1 x 45˚ 7˚ 2 A 1.52 ±0.05 1 MAX.1) 7˚ 0.35 ±0.1 x 45˚ 3 ±0.06 0.2 3.29 ±0.08 4.06 ±0.08 1.9 MAX. (0.25) 0.15 MAX. 4.16 ±0.05 (0.79) 0.6 MAX. 0.2 +0.1 0.4 ±0.05 1.27±0.25 1 2 3 1.27±0.25 18 ±0.5 6 ±0.5 1-1 38 MAX. 9 +0.75 -0.5 23.8 ±0.5 12.7 ±1 A Adhesive Tape Tape 6.35 ±0.4 1) No solder function area Figure 11 Datasheet 4 ±0.3 12.7 ±0.3 Total tolerance at 10 pitches ±1 0.25 -0.15 0.39 ±0.1 GPO05358 PG-SSO-3-2 Package Outline 16 Rev. 1.0, 2009-05-04 www.infineon.com Published by Infineon Technologies AG