PCK946 Low voltage 1 : 10 CMOS clock driver Rev. 01 — 13 December 2005 Product data sheet 1. General description The PCK946 is a low voltage CMOS 1 : 10 clock buffer. The 10 outputs can be configured into a standard fan-out buffer or into 1× and 1⁄2× combinations. The ten outputs were designed and optimized to drive 50 Ω series or parallel terminated transmission lines. With output-to-output skews of 350 ps, the PCK946 is ideal as a clock distribution chip for synchronous systems which need a tight level of skew from a large number of outputs. With an output impedance of approximately 7 Ω, in both the HIGH and LOW logic states, the output buffers of the PCK946 are ideal for driving series terminated transmission lines. More specifically, each of the 10 PCK946 outputs can drive two series terminated transmission lines. With this capability, the PCK946 has an effective fan-out of 1 : 20 in applications using point-to-point distribution schemes. The PCK946 has the capability of generating 1× and 1⁄2× signals from a 1× source. The design is fully static; the signals are generated and re-timed inside the chip to ensure minimal skew between the 1× and 1⁄2× signals. The device features selectability to allow the user to select the ratio of 1× outputs to 1⁄2× outputs. Two independent LVCMOS/LVTTL compatible clock inputs are available. Designers can take advantage of this feature to provide redundant clock sources or the addition of a test clock into the system design. With the TCLK_SEL input pulled HIGH, the TCLK1 input is selected. All of the control inputs are LVCMOS/LVTTL compatible. The DSELn pins choose between 1× and 1⁄2× outputs. A LOW on the DSELn pins will select the 1× output. The MR/OE input will reset the internal flip-flops and 3-state the outputs when it is forced HIGH. The PCK946 is fully 3.3 V compatible. The 32-lead LQFP package was chosen to optimize performance, board space, and cost of the device. The 32-lead LQFP package has a 7 mm × 7 mm body size with a conservative 0.8 mm pin spacing. 2. Features ■ ■ ■ ■ ■ ■ ■ 2 selectable LVCMOS/LVTTL clock inputs 350 ps output-to-output skew Drives up to 20 series terminated independent clock lines Maximum input/output frequency of 150 MHz 3-stateable outputs 32-lead LQFP packaging 3.3 V VCC supply voltage PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 3. Ordering information Table 1: Ordering information Type number PCK946BD Package Name Description Version LQFP32 plastic low profile quad flat package; 32 leads; body 7 × 7 × 1.4 mm SOT358-1 4. Functional diagram TCLK_SEL TCLK0 TCLK1 DSELA (internal pull-down) (internal pull-up) (internal pull-up) PCK946 ÷1 0 0 3 ÷2 1 R QA[0:2] 1 (internal pull-down) 0 3 QB[0:2] 1 DSELB (internal pull-down) 0 4 QC[0:3] 1 DSELC MR/OE (internal pull-down) (internal pull-down) 002aaa676 Fig 1. Functional diagram of PCK946 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 2 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 5. Pinning information 25 VCC 26 QA2 27 GND 28 QA1 29 VCC 30 QA0 31 GND 32 MR/OE 5.1 Pinning TCLK_SEL 1 24 GND VCCI 2 23 QB0 TCLK0 3 22 VCC TCLK1 4 DSELA 5 DSELB 6 19 QB2 DSELC 7 18 VCC GNDI 8 17 VCC 21 QB1 QC3 16 20 GND GND 15 QC2 14 VCC 13 QC1 12 GND 11 9 VCC QC0 10 PCK946BD 002aaa677 Fig 2. Pin configuration for LQFP32 5.2 Pin description Table 2: Pin description Symbol Pin Description DSELA, DSELB, DSELC 5, 6, 7 output bank divide select input GND 11, 15, 20, 24, 27, 31 ground GNDI 8 ground MR/OE 32 internal reset and output (high-impedance) control QA0, QA1, QA2 30, 28, 26 bank A outputs QB0, QB1, QB2 23, 21, 19 bank B outputs QC0, QC1, QC2, QC3 10, 12, 14, 16 bank C outputs TCLK_SEL 1 CMOS clock select input TCLK0, TCLK1 3, 4 CMOS clock inputs VCC 9, 13, 17, 18, 22, 25, 29 supply voltage VCCI 2 supply voltage 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 3 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 6. Functional description 6.1 Function table Table 3: TCLK_SEL function table TCLK_SEL Input 0 TCLK0 1 TCLK1 Table 4: DSELn function table DSELn Outputs 0 1× 1 1⁄ × 2 Table 5: MR/OE function table MR/OE Outputs 0 enabled 1 high-impedance 7. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VCC supply voltage VI input voltage II input current Tstg storage temperature Conditions CMOS inputs 9397 750 12296 Product data sheet Min Max Unit −0.3 +4.6 V −0.3 VCC + 0.3 V - ±20 mA −40 +125 °C © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 4 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 8. Static characteristics Table 7: Static characteristics Tamb = 0 °C to +70 °C; VCC = 3.3 V ± 0.3 V Symbol Parameter VIH HIGH-state input voltage VIL LOW-state input voltage VOH HIGH-state output voltage Conditions LOW-state output voltage VOL II input current Ci input capacitance CPD power dissipation capacitance Iq(max) maximum quiescent supply current Min Typ Max Unit 2.0 - 3.6 V - - 0.8 V IOH = −20 mA [1] 2.5 - - V IOL = 20 mA [1] - - 0.4 V [2] - - ±120 µA - - 4 pF - 25 - pF - 1 2 mA per output [1] The PCK946 can drive 50 Ω transmission lines on the incident edge. Each output can drive one 50 Ω parallel terminated transmission line to the termination voltage of VT = 0.5VCC. Alternately, the device drives up to two 50 Ω series terminated transmission lines. [2] II current is a result of internal pull-up/pull-down resistors. 9. Dynamic characteristics Table 8: Dynamic characteristics Symbol Parameter Conditions [1] maximum input clock frequency fmax MHz 4.5 7.5 11.5 ns 4.5 7.5 11.5 ns fmax < 100 MHz; same frequency outputs - - 350 ps fmax < 100 MHz; different frequency outputs - - 350 ps fmax > 100 MHz; same frequency outputs - - 350 ps fmax > 100 MHz; different frequency outputs - - 450 ps [3] - 2.0 4.5 ns LOW-to-HIGH propagation delay TCLK to Qn HIGH-to-LOW propagation delay TCLK to Qn [1] [2] output-to-output [1] [2] process skew time Unit - tPHL tsk(pr) Max - tPLH output skew time Typ 150 [1] [2] tsk(o) Min part-to-part tPZL OFF-state to LOW propagation delay [2] - 3 11 ns tPZH OFF-state to HIGH propagation delay [2] - 3 11 ns LOW to OFF-state propagation delay [2] - 3 11 ns HIGH to OFF-state propagation delay [2] - 3 11 ns tr rise time output; 0.8 V to 2.0 V [2] 0.1 0.5 1.0 ns tf fall time output; 2.0 V to 0.8 V [2] 0.1 0.5 1.0 ns tPLZ tPHZ [1] Driving 50 Ω transmission lines. [2] Termination is 50 Ω to 0.5VCC. [3] Part-to-part skew at a given temperature and voltage. 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 5 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 10. Application information 10.1 Driving transmission lines The PCK946 clock driver was designed to drive high speed signals in a terminated transmission line environment. To provide the optimum flexibility to the user the output drivers were designed to exhibit the lowest impedance possible. With an output impedance of approximately 10 Ω the drivers can drive either parallel or series terminated transmission lines. In most high performance clock networks point-to-point distribution of signals is the method of choice. In a point-to-point scheme either series terminated or parallel terminated transmission lines can be used. The parallel technique terminates the signal at the end of the line with a 50 Ω resistance to 0.5VCC. This technique draws a fairly high level of DC current and thus only a single terminated line can be driven by each output of the PCK946 clock driver. For the series terminated case however there is no DC current draw, thus the outputs can drive multiple series terminated lines. Figure 3, illustrates an output driving a single series terminated line versus two series terminated lines in parallel. When taken to its extreme the fan-out of the PCK946 clock driver is effectively doubled due to its capability to drive multiple lines. PCK946 OUTPUT BUFFER Ro IN Zo = 50 Ω Rs = 43 Ω Zo = 50 Ω Rs = 43 Ω Zo = 50 Ω OutA 7Ω PCK946 OUTPUT BUFFER IN Rs = 43 Ω OutB0 Ro 7Ω OutB1 002aaa678 Fig 3. Single versus dual transmission lines The waveform plots of Figure 4 show simulation results of an output driving a single line versus two lines. In both cases the drive capability of the PCK946 output buffers is more than sufficient to drive 50 Ω transmission lines on the incident edge. Note from the delay measurements in the simulations a delta of only 43 ps exists between the two differently loaded outputs. This suggests that the dual line driving need not be used exclusively to maintain the tight output-to-output skew of the PCK946. The output waveform in Figure 4 shows a step in the waveform, this step is caused by the impedance mismatch seen looking into the driver. The parallel combination of the 43 Ω series resistor plus the output impedance does not match the parallel combination of the line impedances. The voltage wave launched down the two lines will equal: Zo 25 V L = V S ------------------------------ = 3.0 ---------- = 1.40 V R s + R o + Z o 53.5 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 6 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver At the load end the voltage will double, due to the near unity reflection coefficient, to 2.8 V. It will then increment towards the quiescent 3.0 V in steps separated by one round trip delay (in this case 4.0 ns). 002aaa679 3.0 voltage (V) OutA td = 3.8956 ns 2.0 IN OutB td = 3.9386 ns 1.0 0 −0.5 0 4 8 12 16 time (ns) Fig 4. Single versus dual waveforms Since this step is well above the threshold region it will not cause any false clock triggering, however designers may be uncomfortable with unwanted reflections on the line. To better match the impedances when driving multiple lines the situation in Figure 5 should be used. In this case the series terminating resistors are reduced such that when the parallel combination is added to the output buffer impedance the line impedance is perfectly matched. PCK946 OUTPUT BUFFER IN Rs = 36 Ω Zo = 50 Ω Rs = 36 Ω Zo = 50 Ω Ro 7Ω 002aaa680 7 Ω + 36 Ω || 36 Ω = 50 Ω || 50 Ω 25 Ω = 25 Ω Fig 5. Optimized dual line termination SPICE level output buffer models are available for engineers who want to simulate their specific interconnect schemes. In addition IV characteristics are in the process of being generated to support the other board level simulators in general use. 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 7 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 11. Package outline LQFP32: plastic low profile quad flat package; 32 leads; body 7 x 7 x 1.4 mm SOT358-1 c y X 24 A 17 16 25 ZE e E HE A A2 A 1 (A 3) wM θ bp Lp pin 1 index L 32 9 detail X 1 8 e ZD v M A wM bp D B HD v M B 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HD HE L Lp v w y mm 1.6 0.20 0.05 1.45 1.35 0.25 0.4 0.3 0.18 0.12 7.1 6.9 7.1 6.9 0.8 9.15 8.85 9.15 8.85 1 0.75 0.45 0.2 0.25 0.1 Z D (1) Z E (1) 0.9 0.5 0.9 0.5 θ o 7 o 0 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT358 -1 136E03 MS-026 JEITA EUROPEAN PROJECTION ISSUE DATE 03-02-25 05-11-09 Fig 6. Package outline SOT358-1 (LQFP32) 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 8 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 12. Soldering 12.1 Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 12.2 Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 seconds and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 °C to 270 °C depending on solder paste material. The top-surface temperature of the packages should preferably be kept: • below 225 °C (SnPb process) or below 245 °C (Pb-free process) – for all BGA, HTSSON..T and SSOP..T packages – for packages with a thickness ≥ 2.5 mm – for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called thick/large packages. • below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages. Moisture sensitivity precautions, as indicated on packing, must be respected at all times. 12.3 Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results: • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 9 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C or 265 °C, depending on solder material applied, SnPb or Pb-free respectively. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 12.4 Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 °C and 320 °C. 12.5 Package related soldering information Table 9: Suitability of surface mount IC packages for wave and reflow soldering methods Package [1] Soldering method Wave Reflow [2] BGA, HTSSON..T [3], LBGA, LFBGA, SQFP, SSOP..T [3], TFBGA, VFBGA, XSON not suitable suitable DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, HSQFP, HSSON, HTQFP, HTSSOP, HVQFN, HVSON, SMS not suitable [4] suitable PLCC [5], SO, SOJ suitable suitable not recommended [5] [6] suitable SSOP, TSSOP, VSO, VSSOP not recommended [7] suitable CWQCCN..L [8], PMFP [9], WQCCN..L [8] not suitable LQFP, QFP, TQFP [1] For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026); order a copy from your Philips Semiconductors sales office. [2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods. [3] These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible. 9397 750 12296 Product data sheet not suitable © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 10 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver [4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. [5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. [6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. [7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. [8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. [9] Hot bar soldering or manual soldering is suitable for PMFP packages. 13. Abbreviations Table 10: Abbreviations Acronym Description CMOS Complementary Metal Oxide Silicon LVCMOS Low Voltage Complementary Metal Oxide Silicon LVTTL Low Voltage Transistor-Transistor Logic 14. Revision history Table 11: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes PCK946_1 20051213 Product data sheet - 9397 750 12296 - 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 11 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 15. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 16. Definitions customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 18. Trademarks 17. Disclaimers Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners. Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 19. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 12296 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 13 December 2005 12 of 13 PCK946 Philips Semiconductors Low voltage 1 : 10 CMOS clock driver 20. Contents 1 2 3 4 5 5.1 5.2 6 6.1 7 8 9 10 10.1 11 12 12.1 12.2 12.3 12.4 12.5 13 14 15 16 17 18 19 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 5 Application information. . . . . . . . . . . . . . . . . . . 6 Driving transmission lines . . . . . . . . . . . . . . . . . 6 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 8 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Introduction to soldering surface mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . . 9 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . . 9 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 10 Package related soldering information . . . . . . 10 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 11 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 12 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Contact information . . . . . . . . . . . . . . . . . . . . 12 © Koninklijke Philips Electronics N.V. 2005 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 13 December 2005 Document number: 9397 750 12296 Published in The Netherlands