CYPRESS CY62138F

CY62138F MoBL®
2-Mbit (256K x 8) Static RAM
Functional Description [1]
Features
•
•
•
•
High speed: 45 ns
Wide voltage range: 4.5 V – 5.5 V
Pin compatible with CY62138V
Ultra low standby power
— Typical standby current: 1 µA
— Maximum standby current: 5 µA
• Ultra low active power
•
•
•
•
— Typical active current: 1.6 mA @ f = 1 MHz
Easy memory expansion with CE1, CE2, and OE features
Automatic power down when deselected
CMOS for optimum speed and power
Available in Pb-free 32-pin SOIC and 32-pin TSOP II
packages
The CY62138F is a high performance CMOS static RAM
organized as 256K words by 8 bits. This device features
advanced circuit design to provide ultra low active current.
This is ideal for providing More Battery Life™ (MoBL®) in
portable applications such as cellular telephones. The device
also has an automatic power down feature that significantly
reduces power consumption when addresses are not toggling.
Placing the device into standby mode reduces power
consumption by more than 99% when deselected (CE1 HIGH
or CE2 LOW).
To write to the device, take Chip Enable (CE1 LOW and CE2
HIGH) and Write Enable (WE) inputs LOW. Data on the eight
IO pins (IO0 through IO7) is then written into the location
specified on the address pins (A0 through A17).
To read from the device, take Chip Enable (CE1 LOW and CE2
HIGH) and output enable (OE) LOW while forcing Write
Enable (WE) HIGH. Under these conditions, the contents of
the memory location specified by the address pins appear on
the IO pins.
The eight input and output pins (IO0 through IO7) are placed
in a high impedance state when the device is deselected (CE1
HIGH or CE2 LOW), the outputs are disabled (OE HIGH), or
during a write operation (CE1 LOW and CE2 HIGH and WE
LOW).
Logic Block Diagram
CE1
CE2
IO0
DATA IN DRIVERS
SENSE AMPS
IO1
ROW DECODER
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
256K x 8
ARRAY
IO2
IO3
IO4
IO5
IO6
COLUMN DECODER
WE
IO7
A15
A16
A17
A12
A13
A14
OE
POWER
DOWN
Note
1. For best practice recommendations, refer to the Cypress application note “System Design Guidelines” at http://www.cypress.com.
Cypress Semiconductor Corporation
Document #: 001-13194 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 26, 2007
[+] Feedback
CY62138F MoBL®
Pin Configuration [2]
32-Pin SOIC/TSOP II Pinout
Top View
A17
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
IO0
IO1
IO2
VSS
1
32
31
2
3
4
30
29
5
6
28
27
26
25
7
8
9
10
24
23
22
11
12
13
14
15
16
21
20
19
18
17
VCC
A15
CE2
WE
A13
A8
A9
A11
OE
A10
CE1
IO7
IO6
IO5
IO4
IO3
Product Portfolio
Power Dissipation
VCC Range (V)
Product
CY62138FLL
Speed
(ns)
Min
Typ [3]
Max
4.5V
5.0V
5.5V
45
Operating ICC (mA)
f = 1MHz
f = fmax
Standby ISB2 (µA)
Typ [3]
Max
Typ [3]
Max
Typ [3]
Max
1.6
2.5
13
18
1
5
Notes
2. NC pins are not connected on the die.
3. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25°C.
Document #: 001-13194 Rev. *A
Page 2 of 10
[+] Feedback
CY62138F MoBL®
DC Input Voltage [4, 5] ............ –0.5V to 6.0V (VCCmax + 0.5V)
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................ –65°C to + 150°C
Ambient Temperature with
Power Applied ........................................... –55°C to + 125°C
Supply Voltage to Ground
Potential ................................–0.5V to 6.0V (VCCmax + 0.5V)
DC Voltage Applied to Outputs
in High-Z state [4, 5] ................–0.5V to 6.0V (VCCmax + 0.5V)
Output Current into Outputs (LOW) ............................ 20 mA
Static Discharge Voltage ......................................... > 2001V
(MIL–STD–883, Method 3015)
Latch-up Current ................................................... > 200 mA
Operating Range
Device
CY62138FLL
Range
Ambient
Temperature
VCC [6]
Industrial –40°C to +85°C 4.5V to 5.5V
Electrical Characteristics (Over the Operating Range)
Parameter
Description
Test Conditions
VOH
Output HIGH Voltage
IOH = –1.0 mA
VOL
Output LOW Voltage
IOL = 2.1 mA
VIH
Input HIGH Voltage
VCC = 4.5V to 5.5V
VIL
Input LOW Voltage
VCC = 4.5V to 5.5V
IIX
Input Leakage Current
IOZ
ICC
ISB2 [7]
45 ns
Min
Typ [3]
Unit
Max
2.4
V
0.4
V
2.2
VCC + 0.5
V
–0.5
0.8
V
GND < VI < VCC
–1
+1
µA
Output Leakage Current
GND < VO < VCC, Output Disabled
–1
+1
µA
VCC Operating Supply
Current
f = fmax = 1/tRC
13
18
mA
1.6
2.5
1
5
f = 1 MHz
VCC = VCC(max)
IOUT = 0 mA
CMOS levels
Automatic CE Power Down CE1 > VCC – 0.2V or CE2 < 0.2V
Current CMOS inputs
VIN > VCC – 0.2V or VIN < 0.2V,
f = 0, VCC = VCC(max)
µA
Capacitance (For all packages) [8]
Parameter
Description
CIN
Input capacitance
COUT
Output capacitance
Test Conditions
TA = 25°C, f = 1 MHz,
VCC = VCC(typ)
Max
Unit
10
pF
10
pF
Thermal Resistance [8]
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test Conditions
Still air, soldered on a 3 × 4.5 inch
two-layer printed circuit board
SOIC
TSOP II
Unit
44.53
44.16
°C/W
24.05
11.97
°C/W
Notes
4. VIL(min) = –2.0V for pulse durations less than 20 ns.
5. VIH(max) = VCC+0.75V for pulse durations less than 20ns.
6. Full device AC operation assumes a 100 µs ramp time from 0 to VCC(min) and 200 µs wait time after VCC stabilization.
7. Only chip enables (CE1 and CE2) must be at CMOS level to meet the ISB2 / ICCDR spec. Other inputs can be left floating.
8. Tested initially and after any design or process changes that may affect these parameters.
Document #: 001-13194 Rev. *A
Page 3 of 10
[+] Feedback
CY62138F MoBL®
AC Test Loads and Waveforms
R1
VCC
OUTPUT
ALL INPUT PULSES
3.0V
R2
30 pF
INCLUDING
JIG AND
SCOPE
90%
10%
90%
10%
GND
Rise Time = 1 V/ns
Equivalent to:
Fall Time = 1 V/ns
THEVENIN EQUIVALENT
RTH
OUTPUT
V
Parameters
5.0V
Unit
R1
1800
Ω
R2
990
Ω
RTH
639
Ω
VTH
1.77
V
Data Retention Characteristics (Over the Operating Range)
Parameter
VDR
ICCDR
Description
Conditions
VCC for Data Retention
[7]
Typ [3]
Min
Max
2.0
V
VCC= VDR, CE1 > VCC − 0.2V or CE2 < 0.2V,
VIN > VCC - 0.2V or VIN < 0.2V
Data Retention Current
tCDR [8]
Chip Deselect to Data
Retention Time
tR [9]
Operation Recovery Time
Unit
1
µA
5
0
ns
tRC
ns
Data Retention Waveform [10]
DATA RETENTION MODE
VCC
VCC(min)
tCDR
VDR > 2.0V
VCC(min)
tR
CE
Notes:
9. Full device AC operation requires linear VCC ramp from VDR to VCC(min) > 100 µs or stable at VCC(min) > 100 µs.
10. CE is the logical combination of CE1 and CE2. When CE1 is LOW and CE2 is HIGH, CE is LOW; when CE1 is HIGH or CE2 is LOW, CE is HIGH.
Document #: 001-13194 Rev. *A
Page 4 of 10
[+] Feedback
CY62138F MoBL®
Switching Characteristics (Over the Operating Range) [11]
Parameter
45 ns
Description
Min
Max
Unit
Read Cycle
tRC
Read Cycle Time
tAA
Address to Data Valid
tOHA
Data Hold from Address Change
tACE
CE1 LOW and CE2 HIGH to Data Valid
45
ns
tDOE
OE LOW to Data Valid
22
ns
tLZOE
OE LOW to Low-Z [12]
tHZOE
OE HIGH to High-Z
tLZCE
45
45
10
10
[12, 13]
tHZCE
CE1 HIGH or CE2 LOW to High-Z
tPU
CE1 LOW and CE2 HIGH to power up
Write Cycle
ns
18
[12]
ns
ns
18
0
CE1 HIGH or CE2 LOW to power down
ns
ns
5
[12, 13]
CE1 LOW and CE2 HIGH to Low Z
tPD
ns
ns
ns
45
ns
[14]
tWC
Write Cycle Time
45
ns
tSCE
CE1 LOW and CE2 HIGH to Write End
35
ns
tAW
Address Setup to Write End
35
ns
tHA
Address Hold from Write End
0
ns
tSA
Address Setup to Write Start
0
ns
tPWE
WE Pulse Width
35
ns
tSD
Data Setup to Write end
25
ns
tHD
Data Hold from Write End
0
ns
[12, 13]
tHZWE
WE LOW to High-Z
tLZWE
WE HIGH to Low-Z [12]
18
10
ns
ns
Notes
11. Test conditions for all parameters other than tri-state parameters assume signal transition time of 3 ns (1V/ns) or less, timing reference levels of VCC(typ)/2, input
pulse levels of 0 to VCC(typ), and output loading of the specified IOL/IOH as shown in the AC Test Loads and Waveforms on page 4.
12. At any given temperature and voltage condition, tHZCE is less than tLZCE , tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device.
13. tHZOE, tHZCE, and tHZWE transitions are measured when the outputs enter a high impedance state.
14. The internal write time of the memory is defined by the overlap of WE, CE1 = VIL, and CE2 = VIH. All signals must be ACTIVE to initiate a write and any of these
signals can terminate a write by going INACTIVE. The data input setup and hold timing must be referenced to the edge of the signal that terminates the write.
Document #: 001-13194 Rev. *A
Page 5 of 10
[+] Feedback
CY62138F MoBL®
Switching Waveforms
Read Cycle 1 (Address transition controlled) [15, 16]
tRC
RC
ADDRESS
tOHA
DATA OUT
tAA
PREVIOUS DATA VALID
DATA VALID
Read Cycle No. 2 (OE controlled) [10, 16, 17]
ADDRESS
tRC
CE
tACE
OE
tHZOE
tDOE
tHZCE
tLZOE
HIGH IMPEDANCE
DATA OUT
DATA VALID
tLZCE
tPD
tPU
VCC
SUPPLY
CURRENT
HIGH
IMPEDANCE
50%
50%
ICC
ISB
Write Cycle No. 1 (WE controlled) [10, 14, 18, 19]
tWC
ADDRESS
tSCE
CE
tAW
tSA
tHA
tPWE
WE
OE
tSD
DATA IO
NOTE 20
tHD
DATA VALID
tHZOE
Notes:
15. The device is continuously selected. OE, CE1 = VIL, CE2 = VIH.
16. WE is HIGH for read cycle.
17. Address valid before or similar to CE1 transition LOW and CE2 transition HIGH.
18. Data IO is high impedance if OE = VIH.
19. If CE1 goes HIGH or CE2 goes LOW simultaneously with WE HIGH, the output remains in high impedance state.
20. During this period, the IOs are in output state. Do not apply input signals.
Document #: 001-13194 Rev. *A
Page 6 of 10
[+] Feedback
CY62138F MoBL®
Switching Waveforms (continued)
Write Cycle No. 2 (CE1 or CE2 controlled) [10, 14, 18, 19]
tWC
ADDRESS
tSCE
CE
tSA
tAW
tHA
tPWE
WE
tSD
DATA IO
tHD
DATA VALID
Write Cycle No. 3 (WE controlled, OE LOW) [10, 19]
tWC
ADDRESS
tSCE
CE
tAW
tSA
tHA
tPWE
WE
tSD
NOTE 20
DATA IO
tHD
DATA VALID
tLZWE
tHZWE
Truth Table
CE
WE
OE
H
X
X
High Z
Inputs/Outputs
Deselect/Power Down
Mode
Standby (ISB)
Power
L
H
L
Data Out
Read
Active (ICC)
L
L
X
Data In
Write
Active (ICC)
L
H
H
High Z
Selected, Outputs Disabled
Active (ICC)
Ordering Information
Speed
(ns)
45
Ordering Code
Package
Diagram
Package Type
CY62138FLL-45SXI
51-85081 32-pin Small Outline Integrated Circuit (Pb-free)
CY62138FLL-45ZSXI
51-85095 32-pin Thin Small Outline Package II (Pb-free)
Operating
Range
Industrial
Contact your local Cypress sales representative for availability of these parts.
Document #: 001-13194 Rev. *A
Page 7 of 10
[+] Feedback
CY62138F MoBL®
Package Diagrams
Figure 1. 32-pin (450 Mil) Molded SOIC, 51-85081
16
1
0.546[13.868]
0.566[14.376]
0.440[11.176]
0.450[11.430]
17
32
0.793[20.142]
0.817[20.751]
0.006[0.152]
0.012[0.304]
0.101[2.565]
0.111[2.819]
0.118[2.997]
MAX.
0.004[0.102]
0.050[1.270]
BSC.
0.004[0.102]
MIN.
0.014[0.355]
0.020[0.508]
SEATING PLANE
Document #: 001-13194 Rev. *A
0.047[1.193]
0.063[1.600]
0.023[0.584]
0.039[0.990]
51-85081-*B
Page 8 of 10
[+] Feedback
CY62138F MoBL®
Package Diagrams (continued)
Figure 2. 32-Pin TSOP II, 51-85095
51-85095-**
MoBL is a registered trademark, and More Battery Life is a trademark, of Cypress Semiconductor. All product and company names
mentioned in this document may be the trademarks of their respective holders.
Document #: 001-13194 Rev. *A
Page 9 of 10
© Cypress Semiconductor Corporation, 2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY62138F MoBL®
Document History Page
Document Title: CY62138F MoBL® 2-Mbit (256K x 8) Static RAM
Document Number: 001-13194
REV.
ECN NO. Issue Date
Orig. of
Change
Description of Change
**
797956
See ECN
VKN
New Data Sheet
*A
940341
See ECN
VKN
Added footnote #7 related to ISB2 and ICCDR
Document #: 001-13194 Rev. *A
Page 10 of 10
[+] Feedback