KINGBRIGHT APHHS1005SYCK

1.0X0.5mm SMD CHIP LED LAMP
APHHS1005SYCK
Features
SUPER BRIGHT YELLOW
Description
1.0mmX0.5mm SMT LED, 0.5mm THICKNESS.
The Super Bright Yellow source color devices are
LOW POWER CONSUMPTION.
made with DH InGaAlP on GaAs substrate Light
W IDE VIEW ING ANGLE.
Emitting Diode.
IDEAL FOR BACKLIGHT AND INDICATOR.
VARIOUS COLORS AND LENS TYPES AVAILABLE.
PACKAGE: 2000PCS / REEL .
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3.Specifications are subject to change without notice.
SPEC NO: DSAD0913
REV NO: V.4
DATE: MAR/11/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: B.H.LI
ERP: 1203001435
Selection Guide
Part No.
Dice
APHHS1005SYCK
Iv (mcd)
@ 20mA
Lens Type
SUPER BRIGHT YELLOW (InGaAIP)
Viewing
Angle
Min.
Typ.
2θ
θ1/2
18
120
120°
WATER CLEAR
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Yellow
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Super Bright Yellow
590
nm
IF=20mA
Spectral Line Half-width
Super Bright Yellow
20
nm
IF=20mA
C
Capacitance
Super Bright Yellow
20
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Yellow
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Yellow
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
Forward Current
30
mA
Peak Forward Current [1]
175
mA
5
V
Reverse Voltage
Operating / Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD0913
REV NO: V.4
DATE: MAR/11/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: B.H.LI
ERP: 1203001435
Super Bright Yellow
APHHS1005SYCK
SPEC NO: DSAD0913
REV NO: V.4
DATE: MAR/11/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: B.H.LI
ERP: 1203001435
APHHS1005SYCK
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength) , the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD0913
REV NO: V.4
DATE: MAR/11/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: B.H.LI
ERP: 1203001435