KINGBRIGHT APD2520SYC03

4.5x2mm SMD CHIP LED LAMP
APD2520SYC03
Features
SUPER BRIGHT YELLOW
Description
4.5x2mm SMT LED,0.5mm THICKNESS
The Super Bright Yellow device is made with DH InGaAlP
LOW POWER CONSUMPTION.
(on GaAs substrate) light emitting diode chip.
IDEAL FOR BACKLIGHT AND INDICATOR.
VARIOUS COLORS AND LENS TYPES AVAILABLE.
PACKAGE : 1000PCS/REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3.Specifications are subject to change without notice.
SPEC NO: DSAD1075
REV NO: V.2
DATE: MAR/10/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1203001049
Selection Guide
Part No.
Dice
APD2520SYC03
Iv (mcd)
@ 20mA
Lens Type
SUPER BRIGHT YELLOW (InGaAlP)
WATER CLEAR
Viewing
Angle
Min.
Typ.
2 θ 1/2
110
450
20°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Yellow
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Super Bright Yellow
588
nm
IF=20mA
Spectral Line Half-width
Super Bright Yellow
28
nm
IF=20mA
C
Capacitance
Super Bright Yellow
25
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Yellow
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Yellow
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1075
REV NO: V.2
DATE: MAR/10/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1203001049
Super Bright Yellow
APD2520SYC03
SPEC NO: DSAD1075
REV NO: V.2
DATE: MAR/10/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1203001049
APD2520SYC03
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength) , the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD1075
REV NO: V.2
DATE: MAR/10/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1203001049