KINGBRIGHT AA3020SYC

3.0x2.0mm SURFACE MOUNT LED LAMP
AA3020SYC
Features
SUPER BRIGHT YELLOW
Description
3.0MM X 2.0MM, 1.4MM HIGH, ONLY MINIMUM
The Super Bright Yellow device is made with DH InGaAlP
SPACE REQUIRED.
(on GaAs substrate) light emitting diode chip.
SUITABLE FOR COMPACT OPTOELECTRONIC
APPLICATIONS.
LOW POWER CONSUMPTION.
PACKAGE : 2000PCS / REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3.Specifications are subject to change without notice.
SPEC NO: DSAD1218
REV NO: V.2
DATE: MAR/05/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP:1201000147
Selection Guide
Part No.
Dice
SUPER BRIGHT YELLOW (InGaAIP)
AA3020SYC
Iv (mcd)
@ 20mA
Lens Type
Viewing
Angle
Min.
Typ.
2θ
θ1/2
50
120
90°
WATER CLEAR
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Yellow
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Super Bright Yellow
588
nm
IF=20mA
Spectral Line Half-width
Super Bright Yellow
28
nm
IF=20mA
C
Capacitance
Super Bright Yellow
25
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Yellow
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Yellow
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1218
REV NO: V.2
DATE: MAR/05/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP:1201000147
Super Bright Yellow
AA3020SYC
SPEC NO: DSAD1218
REV NO: V.2
DATE: MAR/05/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP:1201000147
AA3020SYC
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength), the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD1218
REV NO: V.2
DATE: MAR/05/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.W.WANG
ERP:1201000147