rev. PART NUMBER: CZT01 page 1 of 4 date 7/2008 DESCRIPTION: incremental encoder ELECTRICAL SPECIFICATIONS current consumption supply voltage supply current 100mA or less (under no load) 10 V dc 1 mA output resolution (ppr) contact resistance insulation resistance dielectric strength 12 500mΩ max. 50MΩ min. 50 V ac (50 ~ 60 Hz, cut-off current 2 mA) is applied between non-connected terminals and between terminals and the metal frame for 60 ±5 seconds MECHANICAL SPECIFICATIONS detent points shaft play in axial direction rotational torque rotational life mounting height mechanical strength 12 detent points each (detent angle: 30° ±3°) 0.3 mm max. 14 ~ 40 gf·cm 100000 cycles (at 3~30 cycles per minute with 0.5 mA, 5 V dc load) 7 ± 0.1mm free from mechanical abnormalities after test (testing detailed in figure 1) ENVIRONMENTAL SPECIFICATIONS operating temp humidity vibration proof -25° to +85° C ≤85% RH 10 ~ 55 Hz / 1.5mm 2h each X, Y, Z FIGURE 1 Mount the product to the P.C.B. and apply a static force of 10 gf·cm minimum. Contact resistance: 5Ω max., Insulation resistance: 10 MΩ min. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 rev. page 2 of 4 date 7/2008 DESCRIPTION: incremental encoder PART NUMBER: CZT01 WEATHER PROOF CHARACTERISTICS item cold proof hot proof moisture resistance temperature cycling salt mist test condition After testing at -25° ± 2°C for 96 hours, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. Measurements will be made within 1 hour after that. Condensation will be eliminated. After testing at 85° ± 2°C for 96 hours, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. Measurements will be made within 1 hour after that. After testing at 40° ± 2°C, 90 ~ 95% RH for 96 hours, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. Measurements will be made within 1 hour after that. Condensation will be eliminated. After 5 cycles of the following conditions, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. Measurements will be made within 1 hour after that. Condensation will be eliminated. evaluation standard After test: Contact resistance: 5Ω max. Insulation resistance: 10 MΩ min. The performance requirements specified in Electrical Specifications will be satisfied. The encoder will be checked after the following test: 1) Temperature: 35 ± 2°C 2) Salt solution: 5 ± 1% (solids by mass) No corrosion will be recognized in Immersion time: 5 minutes the metal sections of the encoder. 3) After immersing, salt deposit will be removed by running water. 4) Duration: 2 hours 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 rev. DESCRIPTION: incremental encoder PART NUMBER: CZT01 OUTPUT WAVEFORM Shaft rotational direction Signal Output A˄Terminal $̚&˅ C.W. B˄Terminal %̚&˅ A˄Terminal $̚&˅ C.C.W. B˄Terminal %̚&˅ SLIDING NOISE F 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 page 3 of 4 date 7/2008 REV. A 9.8 0.386 5.2 0.205 DESCRIPTION NEW DRAWING DATE 7/8/2008 3.00 0.118 0.1 1.74 0.069 0.03 4.1 0.161 7.0 0.276 0.1 3.5 0.138 0.80 0.15 (3 PLCS) 2.0 0.079 0.15 (2 PLCS) 2.0 0.079 0.2 (3 PLCS) 11.6 0.457 0.3 2.5 0.098 2.5 0.098 6.1 0.240 1.8X2.1 (2 PLCS) 10.8 0.425 2.0 0.079 1.0 0.039 (3 PLCS) +0.1 -0.0 TOLERANCE (unless otherwise stated): X.X ±0.5mm X.XX ±0.3mm X.XXX ±0.1mm 5.0 0.197 20050 SW 112th Ave. Tualatin, OR 97062 Phone: 503-612-2300 800-275-4899 Fax: 503-612-2383 Website: www.cui.com P.C.B. Layout TOLERANCE: ±0.1mm TITLE: SLEEVE TERMINAL PC FILE NAME: CZT01 COPYRIGHT 2008 BY CUI INC. BODY RoHS MATERIAL PLATING Brass Brass PBT Nickel Nickel REV: ENCODER PART NO. UNITS: CZT01 DRAWN BY: ZRJ APPROVED BY: A MM [INCHES] SCALE: 4:1