INFINEON BTS441T_08

Smart Power High-Side-Switch
One Channel: 20 mΩ
BTS441T
Product Summary
On-state Resistance
Operating Voltage
Nominal load current
Current limitation
Package
RON
Vbb(on)
IL(ISO)
IL(lim)
20mΩ
4.75 ... 41V
21A
65A
TO-220-5-11
TO-263-5-2
Standard
SMD
TO-220-5-12
Straight
*HQHUDO'HVFULSWLRQ
•
•
N channel vertical power FET with charge pump, ground referenced CMOS compatible input, monolithically
integrated in Smart SIPMOSŠ technology.
• Green Product (RoHS compliant)
Providing embedded protective functions.
• AEC Qualified
$SSOLFDWLRQ
•
•
•
•
μC compatible power switch for 5V, 12 V and 24 V DC applications
All types of resistive, inductive and capacitve loads
Most suitable for loads with high inrush currents, so as lamps
Replaces electromechanical relays, fuses and discrete circuits
%DVLF)XQNWLRQV
•
•
•
•
•
Very low standby current
Optimized static electromagnetic compatibility (EMC)
µC and CMOS compatible
Fast demagnetization of inductive loads
Stable behaviour at undervoltage
3URWHFWLRQ)XQFWLRQV
•
•
•
•
•
•
•
•
Short circuit protection
Current limitation
Overload protection
Thermal shutdown
Overvoltage protection (including load dump) with external
GND-resistor
Reverse battery protection with external GND-resistor
Loss of ground and loss of Vbb protection
Electrostatic discharge (ESD) protection
9EE
,1
/RJLF
ZLWK
SURWHFWLRQ
IXQFWLRQV
352)(7
287
/RDG
*1'
Data sheet
1
Rev. 1.11, 2008-12-09
BTS441T
)XQFWLRQDOGLDJUDP
RYHUYROWDJH
SURWHFWLRQ
LQWHUQDO
YROWDJHVXSSO\
ORJLF
FXUUHQWOLPLW
JDWH
FRQWURO
FKDUJH
SXPS
9%%
FODPSIRU
LQGXFWLYHORDG
287
,1
(6'
WHPSHUDWXUH
VHQVRU
/2$'
*1'
PROFET
3LQ'HILQLWLRQVDQG)XQFWLRQV
3LQFRQILJXUDWLRQ
WRSYLHZ
3LQ
6\PERO
)XQFWLRQ
*1'
/RJLFJURXQG
,1
,QSXWDFWLYDWHVWKHSRZHUVZLWFKLQ
FDVHRIORJLFDOKLJKVLJQDO
9EE
3RVLWLYHSRZHUVXSSO\YROWDJH
7KHWDELVVKRUWHGWRSLQ
1&
1RWFRQQHFWHG
7DE 9%%
*1',11&287
287
2XWSXWWRWKHORDG
7DE
9EE
3RVLWLYHSRZHUVXSSO\YROWDJH
7KHWDELVVKRUWHGWRSLQ
Data sheet
2
Rev. 1.11, 2008-12-09
BTS441T
Maximum Ratings at Tj = 25 °C unless otherwise specified
Parameter
Supply voltage (overvoltage protection see page 4)
Supply voltage for full short circuit protection
Tj Start=-40 ...+150°C
Load dump protection1) VLoadDump = VA + Vs, VA = 13.5 V
RI2)= 2 Ω, RL= 0,5 Ω, td= 200 ms, IN= low or high
Load current (Short-circuit current, see page 5)
Operating temperature range
Storage temperature range
Power dissipation (DC) ; TC≤25°C
Maximal switchable inductance, single pulse
Vbb = 12V, Tj,start = 150°C, TC = 150°C const.
(see diagram, p.8) IL(ISO) = 21 A, RL= 0 Ω: E4)AS=0.7J:
Electrostatic discharge capability (ESD)
IN:
(Human Body Model)
Out to all other pins shorted:
Symbol
Vbb
Vbb
43
34
Unit
V
V
60
V
IL
Tj
Tstg
self-limited
-40 ...+150
-55 ...+150
A
°C
Ptot
125
W
ZL
VESD
2.1
1.0
8.0
mH
kV
-10 ... +16
±2.0
V
mA
≤1
≤ 75
K/W
VLoad dump3)
Values
acc. MIL-STD883D, method 3015.7 and
ESD assn. std. S5.1-1993; R=1.5kΩ; C=100pF
VIN
IIN
Input voltage (DC)
Current through input pin (DC)
see internal circuit diagrams page 7
Thermal resistance
1)
2)
3)
4)
5)
chip - case:
junction - ambient (free air):
SMD version, device on pcb5):
RthJC
RthJA
≤ 33
Supply voltages higher than Vbb(AZ) require an external current limit for the GND pin, e.g. with a 150 Ω
resistor in the GND connection. A resistor for the protection of the input is integrated.
RI = internal resistance of the load dump test pulse generator
VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839
EAS is the maximum inductive switch off energy
Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70μm thick) copper area for Vbb
connection. PCB is vertical without blown air.
Data sheet
3
Rev. 1.11, 2008-12-09
BTS441T
Electrical Characteristics
Parameter and Conditions
Symbol
at Tj =-40...+150°C, Vbb = 12 V unless otherwise specified
Values
min
typ
max
Unit
Load Switching Capabilities and Characteristics
On-state resistance (Vbb (pin3) to OUT (pin5));
IL = 2 A Vbb≥7V:
Tj=25 °C: RON
Tj=150 °C:
--
15
28
20
37
mΩ
17
21
--
A
--
--
2
mA
40
40
90
110
200
250
μs
dV /dton
0.1
--
1
V/μs
-dV/dtoff
0.1
--
1
V/μs
4.75
4.75
4.75
5.0
41
43
-----
-----47
5
--1.5
41
43
43
43
-52
10
10
25
10
V
--
2
4
see diagram page 9
Nominal load current (pin 3 to 5)
‘ISO 10483-1, 6.7:VON=0.5V, TC=85°C
IL(ISO)
Output current (pin 5) while GND disconnected or
GND pulled up6), Vbb=30 V, VIN= 0,
IL(GNDhigh)
see diagram page 7
Turn-on time
IN
Turn-off time
IN
RL = 12 Ω,
Slew rate on
10 to 30% VOUT, RL = 12 Ω,
Slew rate off
70 to 40% VOUT, RL = 12 Ω,
to 90% VOUT: ton
to 10% VOUT: toff
Operating Parameters
Operating voltage
Tj =-40°C Vbb(on)
Tj =+25°C
Tj =+105°C6)
Tj =+150°C
Overvoltage protection7)
Tj =-40°C: Vbb(AZ)
I bb = 40 mA
Tj =+25...+150°C:
Standby current (pin 3) 8)
Tj=-40...+25°C: Ibb(off)
Tj=+105°C6):
VIN=0 see diagram page 9
Tj=+150°C:
IL(off)
Off-State output current (included in Ibb(off))
VIN=0
Operating current (Pin 1)9), VIN=5 V,
IGND
6)
7)
8)
9)
V
μA
μA
mA
not subject to production test, specified by design
see also VON(CL) in table of protection functions and circuit diagram page 7
Measured with load, typ. 40 µA without load.
Add IIN, if VIN>5.5 V
Data sheet
4
Rev. 1.11, 2008-12-09
BTS441T
Parameter and Conditions
Symbol
min
at Tj =-40...+150°C, Vbb = 12 V unless otherwise specified
Protection Functions10)
Current limit (pin 3 to 5)
(see timing diagrams, page 9)
Repetitive short circuit current limit
Tj = Tjt (see timing diagrams, page 10)
Thermal shutdown time11)12)
Values
typ
max
Unit
IL(lim)
Tj =-40°C:
Tj =25°C:
Tj =+150°C:
IL(SCr)
--40
--
-65
-55
85
----
A
A
Tj,start =25°C: Toff(SC)
--
14
--
ms
41
43
150
---
-47
-10
--
-52
--32
V
°C
K
V
--
540
--
mV
(see timing diagram on page 10)
Output clamp (inductive load switch off)
;Tj =-40°C:
Tj=25..150°C: VON(CL)
Thermal overload trip temperature
Tjt
Thermal hysteresis
ΔTjt
Reverse battery (pin 3 to 1) 13)
-Vbb
Reverse battery voltage drop (VOUT > Vbb)
-VON(rev)
IL = -2A
Tj =+150°C:
at VOUT = Vbb - VON(CL), IL= 40 mA
10)
Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not
designed for continuous repetitive operation.
11) not subject to production test, specified by design
12) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70μm thick) copper area for V
bb
connection. PCB is vertical without blown air.
13) Requires 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal
operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature
protection is not active during reverse current operation! Input and Status currents have to be limited (see
max. ratings page 1 and circuit page 7).
Data sheet
5
Rev. 1.11, 2008-12-09
BTS441T
Parameter and Conditions
at Tj =-40...+150°C, Vbb = 12 V unless otherwise specified
Values
min
typ
max
Input14)
Input resistance
Input turn-on threshold voltage
Input turn-off threshold voltage
Input threshold hysteresis
Off state input current (pin 2)
On state input current (pin 2)
2.5
1.2
0.8
-1
4.5
14)
Symbol
RI
VIN(T+)
VIN(T-)
Δ VIN(T)
VIN = 0.4 V: IIN(off)
VIN = 5 V: IIN(on)
see circuit page 7
3.8
--0.3
-12
6.5
2.2
--15
24
Unit
kΩ
V
V
V
μA
μA
If a ground resistor RGND is used, add the voltage drop across this resistor.
Data sheet
6
Rev. 1.11, 2008-12-09
BTS441T
Overvolt. and reverse batt. protection
Terms
9
9EE
,EE
,
9EE
,1
,1
5 ,1
352)(7
9
9
/HDGIUDPH
EE
,1
*1'
5
*1'
287
,/
921
,1
/RJLF
287
9
,*1'
352)(7
=
*1'
9287
5 *1'
6LJQDO*1'
5
5 /RDG
/RDG*1'
VZ1 = 6.1 V typ., VZ2 = 47 V typ., RGND = 150 Ω,
RI= 3.5 kΩ typ.
In case of reverse battery the load current has to be
limited by the load. Temperature protection is not
active
Input circuit (ESD protection)
,1
=
5,
,
GND disconnect
(6'=' ,
,
,
*1'
9EE
The use of ESD zener diodes as voltage clamp at DC
conditions is not recommended.
,1
Inductive and overvoltage output clamp
9 EE
9
*1'
9
EE
9
9
*1'
,1
=
9
21
287
352)(7
Any kind of load. In case of Input=high is VOUT ≈ VIN - VIN(T+) .
287
*1'
352)(7
GND disconnect with GND pull up
VON clamped to 47 V typ.
9EE
,1
352)(7
287
*1'
9
9
EE
,1
9
*1'
Any kind of load. If VGND > VIN - VIN(T+) device stays off
Data sheet
7
Rev. 1.11, 2008-12-09
BTS441T
Vbb disconnect with charged inductive
load
Inductive load switch-off energy
dissipation
( EE
( $6
9EE
KLJK
,1
352)(7
(/RDG
9EE
287
,1
*1'
287
352)(7
/
*1'
9
=/
EE
For inductive load currents up to the limits defined by ZL
(max. ratings and diagram on page 8) each switch is
protected against loss of Vbb.
Consider at your PCB layout that in the case of Vbb disconnection with energized inductive load all the load current
flows through the GND connection.
^
(/
(5
5
/
Energy stored in load inductance:
2
EL = 1/2·L·I L
While demagnetizing load inductance, the energy
dissipated in PROFET is
EAS= Ebb + EL - ER= VON(CL)·iL(t) dt,
with an approximate solution for RL > 0 Ω:
EAS=
IL· L
(V + |VOUT(CL)|)
2·RL bb
OQ(1+ |V
IL·RL
OUT(CL)|
)
Maximum allowable load inductance for
a single switch off
/ I,/Tj,start = 150°C, Vbb = 12 V, RL = 0 Ω
L [mH]
IL [A]
Data sheet
8
Rev. 1.11, 2008-12-09
BTS441T
Typ. on-state resistance
521 I9EE7M; IL = 2 A, IN = high
RON [mΩ]
7M ƒ&
ƒ&
ƒ&
Vbb [V]
Typ. standby current
,EERII I7M; Vbb = 9...34 V, IN1,2 = low
Ibb(off) [μA]
Tj [°C]
Data sheet
9
Rev. 1.11, 2008-12-09
BTS441T
Figure 2b: Switching a lamp,
Timing diagrams
,1
Figure 1a: Vbb turn on:
,1
9
287
9 EE
,
/
W
9
287
Figure 3a: Short circuit
shut down by overtemperature, reset by cooling
proper turn on under all conditions
RWKHUFKDQQHOQRUPDORSHUDWLRQ
,1
,
Figure 2a: Switching a resistive load,
turn-on/off time and slew rate definition:
/
,
,1
,
9287
W
W on
G9GWRQ
/OLP
G9GWRII
W
RII6&
/6&U
W
Heating up may require several milliseconds, depending on
external conditions
Figure 4a: Overtemperature:
Reset if Tj <Tjt
off
,1
,/
9
287
W
7
-
W
Data sheet
10
Rev. 1.11, 2008-12-09
BTS441T
Package Outlines
10 ±0.2
A
9.9 ±0.2
3.7 ±0.3
10.2 ±0.3
9.25 ±0.2
0.05
2.4
C
0.5 ±0.1
0...0.15
5 x 0.8 ±0.1
4 x 1.7
1)
1.6 ±0.3
1.27 ±0.1
8.6 ±0.3
0...0.3
4.4
2.8 ±0.2
1)
12.95
15.65 ±0.3
17 ±0.3
8.5 1)
3.7 -0.15
0.25
3.9 ±0.4
M
A C
8.4 ±0.4
Typical
All metal surfaces tin plated, except area of cut.
figure 5: PG-TO220-5-11
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with
government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e
Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website:
http://www.infineon.com/packages.
Data sheet
11
Dimensions in mm
Rev. 1.11, 2008-12-09
BTS441T
10 ±0.2
A
9.9 ±0.2
B
13 ±0.5
C
0.05
2.4
0.5 ±0.1
0...0.15
2.4
5 x 0.8 ±0.1
4 x 1.7
1)
9.25 ±0.2
1.27 ±0.1
2.8 ±0.2
0...0.3
4.4
11 ±0.5
1)
12.95
15.65 ±0.3
17 ±0.3
8.5 1)
3.7 -0.15
0.25
M
A B C
Typical
Metal surface min. X = 7.25, Y = 12.3
All metal surfaces tin plated, except area of cut.
Figure 6: PG-TO220-5-12
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with
government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e
Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website:
http://www.infineon.com/packages.
Data sheet
12
Dimensions in mm
Rev. 1.11, 2008-12-09
BTS441T
4.4
10 ±0.2
1.27 ±0.1
A
8.5 1)
B
0.05
4.7 ±0.5
2.7 ±0.3
2.4
0.1
1.3 ±0.3
7.55 1)
9.25 ±0.2
(15)
1 ±0.3
0...0.3
0...0.15
5 x 0.8 ±0.1
0.5 ±0.1
4 x 1.7
0.25
M
A B
8˚ MAX.
1) Typical
Metal surface min. X = 7.25, Y = 6.9
All metal surfaces tin plated, except area of cut.
0.1 B
GPT09062
Figure 7: PG-TO263-5-2
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with
government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e
Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website:
http://www.infineon.com/packages.
Data sheet
13
Dimensions in mm
Rev. 1.11, 2008-12-09
BTS441T
Revision History
Revision
Date
Changes
1.11
2008-12-09
RoHS-compliant PG-TO220 and PG-TO263 packages version of the BTS441T
All pages: Infineon logo updated
Page 1:
Added “AEC qualified” and “RoHS” logo, added “Green Product (RoHS
compliant)” and “AEC qualified” statement to feature list, package names changed
to RoHS compliant versions, updated package drawing.
Page 10-12:
Package names changed to RoHS compliant versions ( PG-TO220-5-11, PGTO220-12 and PG-TO263-5-2), added “Green Product” description
added Revision History
added Legal Disclaimer
Data sheet
14
Rev. 1.11, 2008-12-09
Edition 2008-12-09
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2008 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.