Bulletin PD-20615 rev. B 11/03 HFA15TB60S HEXFRED Ultrafast, Soft Recovery Diode TM Features • • • • • 2 VF = 1.7V Qrr * = 84nC Benefits • Reduced RFI and EMI • Reduced Power Loss in Diode and Switching Transistor • Higher Frequency Operation • Reduced Snubbing • Reduced Parts Count VR = 600V Base Cathode Ultrafast Recovery Ultrasoft Recovery Very Low IRRM Very Low Qrr Specified at Operating Conditions 1 N/C di(rec)M/dt * = 188A/µs * 125°C 3 Anode Description International Rectifier's HFA15TB60S is a state of the art ultra fast recovery diode. Employing the latest in epitaxial construction and advanced processing techniques it features a superb combination of characteristics which result in performance which is unsurpassed by any rectifier previously available. With basic ratings of 600 volts and 8 amps per Leg continuous current, the HFA15TB60S is especially well suited for use as the companion diode for IGBTs and MOSFETs. In addition to ultra fast recovery time, the HEXFRED product line features extremely low values of peak recovery current (IRRM) and does not exhibit any tendency to "snap-off" during the tb portion of recovery. The HEXFRED features combine to offer designers a rectifier with lower noise and significantly lower switching losses in both the diode and the switching transistor. These HEXFRED advantages can help to significantly reduce snubbing, component count and heatsink sizes. The HEXFRED HFA15TB60S is ideally suited for applications in power supplies and power conversion systems (such as inverters), motor drives, and many other similar applications where high speed, high efficiency is needed. D2 Pak Absolute Maximum Ratings Parameter VR IF @ TC = 100°C IFSM IFRM PD @ TC = 25°C PD @ TC = 100°C TJ TSTG www.irf.com Cathode-to-Anode Voltage Continuous Forward Current Single Pulse Forward Current Maximum Repetitive Forward Current Maximum Power Dissipation Maximum Power Dissipation Operating Junction and Storage Temperature Range Max. Units 600 15 150 60 74 29 V -55 to +150 A W °C 1 HFA15TB60S Bulletin PD-20615 rev. B 11/03 Electrical Characteristics @ TJ = 25°C (unless otherwise specified) Parameter VBR Cathode Anode Breakdown Voltage VFM Max Forward Voltage IRM Max Reverse Leakage Current CT LS Min. Typ. Max. Units Junction Capacitance 600 ––– ––– ––– ––– ––– ––– ––– ––– 1.3 1.7 1.5 2.0 1.2 1.6 1.0 10 400 1000 25 50 Series Inductance ––– 8.0 ––– V V µA pF nH Test Conditions IR = 100µA IF = 15A See Fig. 1 IF = 30A IF = 15A, TJ = 125°C See Fig. 2 VR = VR Rated TJ = 125°C, VR = 0.8 x VR RatedD Rated See Fig. 3 VR = 200V Measured lead to lead 5mm from package body Dynamic Recovery Characteristics @ TJ = 25°C (unless otherwise specified) Parameter trr trr1 trr2 IRRM1 IRRM2 Qrr1 Qrr2 di(rec)M/dt1 di(rec)M/dt2 Reverse Recovery Time See Fig. 5 Peak Recovery Current See Fig. 6 Reverse Recovery Charge See Fig. 7 Peak Rate of Fall of Recovery Current During tb See Fig. 8 Min. Typ. Max. Units ––– ––– ––– ––– ––– ––– ––– ––– ––– 23 50 105 4.5 6.5 84 241 188 160 ––– 60 120 6.0 10 180 600 ––– ––– Test Conditions IF = 1.0A, dif/dt = 200A/µs, VR = 30V ns TJ = 25°C TJ = 125°C IF = 15A TJ = 25°C A TJ = 125°C VR = 200V TJ = 25°C nC TJ = 125°C dif/dt = 200A/µs TJ = 25°C A/µs TJ = 125°C Thermal - Mechanical Characteristics Parameter Tlead RthJC RthJA Wt c d Lead Temperature Thermal Resistance, Junction to Case Thermal Resistance, Junction to Ambient Weight Min. Typ. Max. Units –––– –––– –––– –––– –––– –––– –––– –––– 2.0 0.07 300 1.7 80 –––– –––– °C K/W g (oz) c 0.063 in. from Case (1.6mm) for 10 sec d Typical Socket Mount 2 www.irf.com HFA15TB60S Bulletin PD-20615 rev. B 11/03 Reverse Current - IR (µA) 10000 T J = 150°C T J = 125°C 10 TJ = 150°C 1000 100 TJ = 125°C 10 1 0.1 TJ = 25°C A 0.01 0 T = 25°C J 200 400 600 Reverse Voltage - V R (V) Fig. 2 - Typical Reverse Current vs. Reverse Voltage 100 1 1.0 A 1.2 1.4 1.6 1.8 2.0 2.2 2.4 Forward Voltage Drop - V FM (V) Fig. 1 - Maximum Forward Voltage Drop vs. Instantaneous Forward Current A Junction Capacitance -CT (pF) Instantaneous Forward Current - IF (A) 100 TJ = 25°C A 10 10 100 1000 Reverse Voltage - V R (V) Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage Thermal Response (Z thJC ) 10 1 D = 0.50 0.20 0.10 0.1 0.01 0.00001 PDM 0.05 t1 0.02 0.01 t2 SINGLE PULSE (THERMAL RESPONSE) 0.0001 Notes: 1. Duty factor D = t 1 / t 2 2. Peak TJ = P DM x Z thJC + TC 0.001 0.01 0.1 1 t1 , Rectangular Pulse Duration (sec) Fig. 4 - Maximum Thermal Impedance Zthjc Characteristics www.irf.com 3 HFA15TB60S Bulletin PD-20615 rev. B 11/03 25 100 VR = 200V TJ = 125°C TJ = 25°C IF = 30A I F = 15A 80 20 I F = 5.0A I F = 30A trr- (nC) Irr- ( A) 60 I F = 5.0A 40 10 20 5 VR = 200V TJ = 125°C TJ = 25°C 0 100 A di f /dt - (A/µs) di f /dt - (A/µs) 1000 Fig. 6 - Typical Recovery Current vs. dif/dt 800 600 A 0 100 1000 Fig. 5 - Typical Reverse Recovery vs. dif/dt 700 I F = 15A 15 10000 VR = 200V TJ = 125°C TJ = 25°C VR = 200V TJ = 125°C TJ = 25°C I F = 30A I F = 15A I F = 5.0A di (rec) M/dt- (A /µs) Qrr- (nC) 500 400 300 I F = 30A 1000 I F = 15A IF = 5.0A 200 100 0 100 A di f /dt - (A/µs) Fig. 7 - Typical Stored Charge vs. dif/dt 4 1000 100 100 A di f /dt - (A/µs) 1000 Fig. 8 - Typical di(rec)M/dt vs. dif/dt www.irf.com HFA15TB60S Bulletin PD-20615 rev. B 11/03 3 t rr IF REVERSE RECOVERY CIRCUIT tb ta 0 V R = 200V 2 Q rr I RRM 4 0.5 I RRM di(rec)M/dt 0.01 Ω L = 70µH D.U.T. dif/dt ADJUST D G IRFP250 S Fig. 9 - Reverse Recovery Parameter Test Circuit www.irf.com 5 0.75 I RRM 1 di f /dt 1. dif/dt - Rate of change of current through zero crossing 2. IRRM - Peak reverse recovery current 3. trr - Reverse recovery time measured from zero crossing point of negative going IF to point where a line passing through 0.75 IRRM and 0.50 IRRM extrapolated to zero current 4. Qrr - Area under curve defined by trr and IRRM trr X IRRM Qrr = 2 5. di(rec)M/dt - Peak rate of change of current during tb portion of trr Fig. 10 - Reverse Recovery Waveform and Definitions 5 HFA15TB60S Bulletin PD-20615 rev. B 11/03 Outline Table 4.69 (0.18) 4.20 (0.16) 10.16 (0.40) REF. 1.32 (0.05) 1.22 (0.05) 6.47 (0.25) 15.49 (0.61) 93° 6.18 (0.24) 14.73 (0.58) 5.28 (0.21) 2.61 (0.10) 4.78 (0.19) 2.32 (0.09) 0.55 (0.02) 8.89 (0.35) 3X REF. 1.40 (0.055) 1.14 (0.045) 2X 1 0.46 (0.02) 0.93 (0.37) MINIMUM RECOMMENDED FOOTPRINT 0.69 (0.27) 11.43 (0.45) 3 4.57 (0.18) 4.32 (0.17) 2 8.89 (0.35) 17.78 (0.70) 0.61 (0.02) MAX. 5.08 (0.20) REF. 3.81 (0.15) 2.08 (0.08) 2X 2.54 (0.10) 2X Conforms to JEDEC Outline D2PAK Dimensions in millimeters and inches Part Marking Information EXAMPLE: THIS IS AN HFA15TB60S PART NUMBER (K) INTERNATIONAL RECTIFIER LOGO HFA15TB60S 5K3A 9712 ASSEMBLY LOT CODE (N/C) 6 (A) DATE CODE (YYWW) YY = YEAR WW = WEEK www.irf.com HFA15TB60S Bulletin PD-20615 rev. B 11/03 Tape & Reel Information TRR 1.60 (0.063) 1.50 (0.059) 4.10 (0.161) 3.90 (0.153) 1.60 (0.063) 1.50 (0.059) DIA. 0.368 (0.0145) 0.342 (0.0135) FEED DIRECTION 1.85 (0.073) 1.65 (0.065) 11.60 (0.457) 11.40 (0.449) 15.42 (0.609) 15.22 (0.601) TRL 1.75 (0.069) 10.90 (0.429) 10.70 (0.421) 1.25 (0.049) 24.30 (0.957) 23.90 (0.941) DIA. 16.10 (0.634) 4.72 (0.186) 4.52 (0.178) 15.90 (0.626) FEED DIRECTION 13.50 (0.532) DIA. 12.80 (0.504) 26.40 (1.039) 24.40 (0.961) SMD-220 Tape & Reel When ordering, indicate the part 360 (14.173) DIA. MAX. 60 (2.362) number, part orientation, and the quantity. Quantities are in multiples of 800 pieces per reel for both TRL and TRR. D IA . MIN . Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 11/03 www.irf.com 7