LINER LDPR

LT3470A
Micropower Buck Regulator
with Integrated Boost and
Catch Diodes
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
Low Quiescent Current: 35μA at 12VIN to 3.3VOUT
Integrated Boost and Catch Diodes
Input Range: 4V to 40V
3.3V at 250mA from 4V to 40V Input
5V at 250mA from 5.7V to 40V Input
Low Output Ripple: <10mV
< 1μA in Shutdown Mode
Output Voltage: 1.25V to 16V
Hysteretic Mode Control
– Low Ripple Burst Mode® Operation at Light Loads
– Continuous Operation at Higher Loads
Solution Size as Small as 50mm2
Low Profile (0.75mm) 2mm × 3mm Thermally
Enhanced 8-Lead DFN Package
APPLICATIONS
n
n
n
n
n
Automotive Battery Regulation
Power for Portable Products
Distributed Supply Regulation
Industrial Supplies
Wall Transformer Regulation
The LT®3470A is a micropower step-down DC/DC converter that integrates a 440mA power switch, catch diode
and boost diode into low profile 2mm × 3mm DFN
package. The LT3470A combines Burst Mode and
continuous operation to allow the use of tiny inductor
and capacitors while providing a low ripple output to
loads of up to 250mA.
With its wide input range of 4V to 40V, the LT3470A can
regulate a wide variety of power sources, from 2-cell Li-Ion
batteries to unregulated wall transformers and lead-acid
batteries. Quiescent current in regulation is just 35μA in
a typical application while a zero current shutdown mode
disconnects the load from the input source, simplifying
power management in battery-powered systems. Fast current limiting and hysteretic control protects the LT3470A
and external components against shorted outputs, even
at 40V input. The LT3470A has higher output current and
improved start-up and dropout performance compared
to the LT3470.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. Burst Mode
is a registered trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
TYPICAL APPLICATION
Efficiency and Power Loss vs Load Current
90
VIN
5.7V TO 40V
1000
VIN = 12V
80
0.22μF
SHDN
33μH
VOUT
5V
250mA
SW
BIAS
22pF
2.2μF
604k
1%
FB
GND
22μF
200k
1%
3470a TA01
EFFICIENCY (%)
OFF ON
70
BOOST
LT3470A
100
60
50
10
40
POWER LOSS (mW)
VIN
1
30
20
10
0.1
0.1
10
100
1
LOAD CURRENT (mA)
300
3470a TA02
3470afa
1
LT3470A
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
VIN, SHDN Voltage ................................................... 40V
BOOST Pin Voltage .................................................. 47V
BOOST Pin Above SW Pin........................................ 25V
FB Voltage .................................................................. 5V
BIAS Voltage .............................................................15V
SW Voltage ................................................................VIN
Maximum Junction Temperature
LT3470AE, LT3470AI ......................................... 125°C
Operating Temperature Range (Note 2)
LT3470AE.............................................– 40°C to 85°C
LT3470AI............................................ –40°C to 125°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) ................. 300°C
TOP VIEW
FB 1
8
SHDN
BIAS 2
7
NC
6
VIN
5
GND
BOOST 3
9
SW 4
DDB8 PACKAGE
8-LEAD (3mm × 2mm) PLASTIC DFN
θJA = 80°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3470AEDDB#PBF
LT3470AEDDB#TRPBF
LDPR
8-Lead (3mm × 2mm) Plastic DFN
–40°C to 85°C
LT3470AIDDB#PBF
LT3470AIDDB#TRPBF
LDPR
8-Lead (3mm × 2mm) Plastic DFN
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3470afa
2
LT3470A
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.
VIN = 10V, VSHDN = 10V, VBOOST = 15V, VBIAS = 3V unless otherwise specified.
PARAMETER
CONDITIONS
MIN
TYP
●
Minimum Input Voltage
MAX
UNITS
4
V
Quiescent Current from VIN
VSHDN = 0.2V
VBIAS = 3V, Not Switching
VBIAS = 0V, Not Switching
●
0.1
10
40
0.5
18
55
μA
μA
μA
Quiescent Current from Bias
VSHDN = 0.2V
VBIAS = 3V, Not Switching
VBIAS = 0V, Not Switching
●
0.1
30
0.1
0.5
60
1.5
μA
μA
μA
FB Comparator Trip Voltage
VFB Falling
●
1.250
1.265
V
FB Pin Bias Current (Note 3)
VFB = 1V
35
35
80
150
nA
nA
0.0006
0.02
%/V
FB Voltage Line Regulation
1.228
●
4V < VIN < 40V
Minimum Switch Off-Time (Note 5)
●
Maximum Duty Cycle
90
Switch Leakage Current
500
ns
95
%
0.7
1.5
μA
Switch VCESAT
ISW = 100mA
150
Switch VCESAT Without Boost
VBOOST = VSW
0.9
1.2
Switch Top Current Limit
VFB = 0V
440
560
Switch Bottom Current Limit
VFB = 0V
280
mA
Catch Schottky Drop
ISW = 100mA
600
mV
320
mV
V
mA
Catch Schottky Reverse Leakage
VSW = 10V
0.2
2
μA
Boost Schottky Drop
IBIAS = 50mA
690
775
mV
Boost Schottky Reverse Leakage
VSW = 10V, VBIAS = 0V
0.2
2
μA
1.7
2.2
V
ISW = 100mA
2.3
5
Bias Pin Preload
VBOOST = 10V
50
SHDN Pin Current
VSHDN = 2.5V
1
●
Minimum Boost Voltage (Note 4)
BOOST Pin Current
SHDN Input Voltage High
SHDN Input Voltage Low
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3470AE is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating
temperature range are assured by design, characterization and correlation
mA
mA
5
2
μA
V
0.2
V
with statistical process controls. The LT3470AI specifications are
guaranteed over the –40°C to 125°C temperature range.
Note 3: Bias current flows out of the FB pin.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the switch.
Note 5: This parameter is assured by design and correlation with statistical
process controls.
3470afa
3
LT3470A
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency, VOUT = 3.3V
Efficiency, VOUT = 5V
VFB vs Temperature
90
90
80
TA = 25°C unless otherwise noted.
L = TOKO D52LC 47μH
TA = 25°C
VIN = 12V
1.260
L = TOKO D52LC 47μH
TA = 25°C
VIN = 7V
VIN = 12V
80
60
50
70
VIN = 24V
VIN = 36V
VFB (V)
VIN = 24V VIN = 36V
EFFICIENCY (%)
EFFICIENCY (%)
1.255
70
60
1.250
50
1.245
40
40
30
0.1
1
10
LOAD CURRENT (mA)
100
30
0.1
1
10
LOAD CURRENT (mA)
1.240
–50
100
75
0
25
50
TEMPERATURE (°C)
–25
3470a G02
3470a G01
100
125
3470a G03
VIN Quiescent Current
vs Temperature
Top and Bottom Switch Current
Limits (VFB = 0V) vs Temperature
50
600
40
500
VIN CURRENT (μA)
CURRENT LIMIT (mA)
550
450
400
350
BIAS < 3V
30
20
300
BIAS > 3V
10
250
200
–50
–25
75
50
25
TEMPERATURE (°C)
0
100
0
–50
125
–25
50
25
0
75
TEMPERATURE (°C)
3470a G04
100
125
3470a G05
SHDN Bias Current
vs Temperature
BIAS Quiescent Current
(Bias > 3V) vs Temperature
30
9
VSHDN = 36V
8
25
SHDN CURRENT (μA)
BIAS CURRENT (μA)
7
20
15
10
6
5
4
3
2
VSHDN = 2.5V
5
1
0
–50
–25
50
25
75
0
TEMPERATURE (°C)
100
125
3470a G06
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
3470a G07
3470afa
4
LT3470A
TYPICAL PERFORMANCE CHARACTERISTICS
FB Bias Current (VFB = 0V)
vs Temperature
60
120
50
100
FB CURRENT (μA)
FB CURRENT (nA)
FB Bias Current (VFB = 1V)
vs Temperature
TA = 25°C unless otherwise noted.
40
30
20
10
80
60
40
20
0
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
0
–50
125
–25
50
25
75
0
TEMPERATURE (°C)
3470a G08
125
3470a G09
Boost Diode VF (IF = 50mA)
vs Temperature
Switch VCESAT (ISW = 100mA)
vs Temperature
300
0.8
0.7
250
0.6
SCHOTTKY VF (V)
SWITCH VCESAT (mV)
100
200
150
100
0.5
0.4
0.3
0.2
50
0.1
0
–50
–25
50
25
75
0
TEMPERATURE (°C)
100
0
–50
125
–25
75
50
25
TEMPERATURE (°C)
0
3470a G10
125
3470a G11
Catch Diode VF (IF = 100mA)
vs Temperature
Diode Leakage (VR = 36V)
vs Temperature
60
0.7
55
SCHOTTKY DIODE LEAKAGE (mA)
0.6
SCHOTTKY VF (V)
100
0.5
0.4
0.3
0.2
0.1
50
CATCH
BOOST
45
40
35
30
25
20
15
10
5
0
–50
–25
50
25
75
0
TEMPERATURE (°C)
100
125
3470a G12
0
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
125
3470a G13
3470afa
5
LT3470A
TYPICAL PERFORMANCE CHARACTERISTICS
BOOST Pin Current
700
14
600
12
BOOST PIN CURRENT (mA)
SWITCH VCESAT (mV)
Switch VCESAT
TA = 25°C unless otherwise noted.
500
400
300
200
100
10
8
6
4
2
0
0
100
0
200
300
400
SWITCH CURRENT (mA)
500
0
100
200
300
400
SWITCH CURRENT (mA)
3470a G14
500
3470a G15
Catch Diode Forward Voltage
Boost Diode Forward Voltage
1.0
900
800
700
SCHOTTKY VF (V)
SCHOTTKY VF (V)
0.8
0.6
0.4
600
500
400
300
200
0.2
100
0
200
100
300
CATCH DIODE CURRENT (mA)
0
0
400
0
100
50
150
BOOST DIODE CURRENT (mA)
3470a G16
3470a G17
Minimum Input Voltage, VOUT = 3.3V
6.0
200
Minimum Input Voltage, VOUT = 5V
8
TA = 25°C
TA = 25°C
7
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
5.5
5.0
4.5
4.0
VIN TO RUN/START
6
VIN TO RUN/START
5
3.5
3.0
0
50
100
150
200
LOAD CURRENT (mA)
250
3470a G18
4
0
50
100
150
200
LOAD CURRENT (mA)
250
3470a G19
3470afa
6
LT3470A
PIN FUNCTIONS
SHDN (Pin 8): The SHDN pin is used to put the LT3470A in
shutdown mode. Tie to ground to shut down the LT3470A.
Apply 2V or more for normal operation. If the shutdown
feature is not used, tie this pin to the VIN pin.
NC (Pin 7): This pin can be left floating, connected to VIN,
or tied to GND.
VIN (Pin 6): The VIN pin supplies current to the LT3470A’s
internal regulator and to the internal power switch. This
pin must be locally bypassed.
GND (Pin 5): Tie the GND pin to a local ground plane
below the LT3470A and the circuit components. Return
the feedback divider to this pin.
BOOST (Pin 3): The BOOST pin is used to provide a drive
voltage, which is higher than the input voltage, to the
internal bipolar NPN power switch.
BIAS (Pin 2): The BIAS pin connects to the internal boost
Schottky diode and to the internal regulator. Tie to VOUT
when VOUT > 2.5V or to VIN otherwise. When VBIAS > 3V the
BIAS pin will supply current to the internal regulator.
FB (Pin 1): The LT3470A regulates its feedback pin to
1.25V. Connect the feedback resistor divider tap to this
pin. Set the output voltage according to VOUT = 1.25V (1
+ R1/R2) or R1 = R2 (VOUT /1.25 – 1).
Exposed Pad (Pin 9): Ground. Must be soldered to PCB.
SW (Pin 4): The SW pin is the output of the internal power
switch. Connect this pin to the inductor, catch diode and
boost capacitor.
3470afa
7
LT3470A
BLOCK DIAGRAM
VIN
VIN
BIAS
C1
+
–
BOOST
500ns
ONE SHOT
R
Qʹ
S
Q
C3
SW
L1
VOUT
–
C2
SHDN
+
ENABLE
BURST MODE
DETECT
NC
VREF
1.25V
gm
GND
FB
R2
R1
3470a BD
3470afa
8
LT3470A
OPERATION
The LT3470A uses a hysteretic control scheme in conjunction with Burst Mode operation to provide low output ripple
and low quiescent current while using a tiny inductor and
capacitors.
Operation can best be understood by studying the Block
Diagram. An error amplifier measures the output voltage
through an external resistor divider tied to the FB pin. If
the FB voltage is higher than VREF, the error amplifier will
shut off all the high power circuitry, leaving the LT3470A
in its micropower state. As the FB voltage falls, the error
amplifier will enable the power section, causing the chip
to begin switching, thus delivering charge to the output
capacitor. If the load is light the part will alternate between
micropower and switching states to keep the output in
regulation (See Figure 1a). At higher loads the part will
switch continuously while the error amp servos the top
and bottom current limits to regulate the FB pin voltage
to 1.25V (See Figure 1b).
The switching action is controlled by an RS latch and
two current comparators as follows: The switch turns on,
and the current through it ramps up until the top current
comparator trips and resets the latch causing the switch
to turn off. While the switch is off, the inductor current
ramps down through the catch diode. When both the bottom current comparator trips and the minimum off-time
one-shot expires, the latch turns the switch back on thus
completing a full cycle. The hysteretic action of this control
scheme results in a switching frequency that depends
on inductor value, input and output voltage. Since the
switch only turns on when the catch diode current falls
below threshold, the part will automatically switch slower
to keep inductor current under control during start-up or
short-circuit conditions.
The switch driver operates from either the input or from
the BOOST pin. An external capacitor and internal diode
is used to generate a voltage at the BOOST pin that is
higher than the input supply. This allows the driver to
fully saturate the internal bipolar NPN power switch for
efficient operation.
If the SHDN pin is grounded, all internal circuits are turned
off and VIN current reduces to the device leakage current,
typically 100nA.
200mA LOAD
NO LOAD
VOUT
20mV/DIV
VOUT
20mV/DIV
IL
100mA/DIV
IL
100mA/DIV
1μs/DIV
1ms/DIV
150mA LOAD
10mA LOAD
VOUT
20mV/DIV
VOUT
20mV/DIV
IL
100mA/DIV
IL
100mA/DIV
5μs/DIV
(1a) Burst Mode Operation
3470a F01a
1μs/DIV
3470a F1b
(1b) Continuous Operation
Figure 1. Operating Waveforms of the LT3470A Converting 12V to 5V Using a 33μH Inductor and 10μF Output Capacitor
3470afa
9
LT3470A
APPLICATIONS INFORMATION
Input Voltage Range
The minimum input voltage required to generate a particular output voltage in an LT3470A application is limited
by either its 4V undervoltage lockout or by its maximum
duty cycle. The duty cycle is the fraction of time that the
internal switch is on and is determined by the input and
output voltages:
VOUT + VD
DC =
VIN – VSW + VD
where VD is the forward voltage drop of the catch diode
(~0.6V) and VSW is the voltage drop of the internal switch
at maximum load (~0.4V). Given DCMAX = 0.90, this leads
to a minimum input voltage of:
V +V VIN(MIN) = OUT D + VSW – VD
DCMAX This analysis assumes the part has started up such that the
capacitor tied between the BOOST and SW pins is charged
to more than 2V. For proper start-up, the minimum input
voltage is limited by the boost circuit as detailed in the
section BOOST Pin Considerations.
The maximum input voltage is limited by the absolute
maximum VIN rating of 40V, provided an inductor of sufficient value is used.
Inductor Selection
The switching action of the LT3470A during continuous
operation produces a square wave at the SW pin that results
in a triangle wave of current in the inductor. The hysteretic
mode control regulates the top and bottom current limits
(see Electrical Characteristics) such that the average inductor current equals the load current. For safe operation, it
must be noted that the LT3470A cannot turn the switch
on for less than ~150ns. If the inductor is small and the
input voltage is high, the current through the switch may
exceed safe operating limit before the LT3470A is able to
turn off. To prevent this from happening, the following
equation provides a minimum inductor value:
LMIN =
VIN(MAX) • tON-TIME(MIN)
where VIN(MAX) is the maximum input voltage for the application, tON-TIME(MIN) is ~150ns and IMAX is the maximum
allowable increase in switch current during a minimum
switch on-time (150mA). While this equation provides a
safe inductor value, the resulting application circuit may
switch at too high a frequency to yield good efficiency.
It is advised that switching frequency be below 1.2MHz
during normal operation:
f=
(1– DC)( VD + VOUT )
L • ΔIL
where f is the switching frequency, ΔIL is the ripple current in the inductor (~200mA), VD is the forward voltage
drop of the catch diode, and VOUT is the desired output
voltage.
If the application circuit is intended to operate at high duty
cycles (VIN close to VOUT), it is important to look at the
calculated value of the switch off-time:
1– DC
tOFF-TIME =
f
The calculated tOFF-TIME should be more than LT3470A’s
minimum tOFF-TIME (See Electrical Characteristics), so the
application circuit is capable of delivering full rated output
current. If the full output current of 250mA is not required,
the calculated tOFF-TIME can be made less than minimum
tOFF-TIME possibly allowing the use of a smaller inductor.
See Table 1 for an inductor value selection guide.
Table 1. Recommended Inductors for Loads up to 250mA
VOUT
VIN Up to 16V
VIN Up to 40V
2.5V
10μH
33μH
3.3V
10μH
33μH
5V
15μH
33μH
12V
33μH
47μH
Choose an inductor that is intended for power applications.
Table 2 lists several manufacturers and inductor series.
For robust output short-circuit protection at high VIN (up
to 40V) use at least a 33μH inductor with a minimum
450mA saturation current. If short-circuit performance is
not required, inductors with ISAT of 300mA or more may
IMAX
3470afa
10
LT3470A
APPLICATIONS INFORMATION
Table 2. Inductor Vendors
VENDOR
URL
PART SERIES
INDUCTANCE RANGE (μH)
SIZE (mm)
Coilcraft
www.coilcraft.com
DO1605
ME3220
DO3314
10 to 47
10 to 47
10 to 47
1.8 × 5.4 × 4.2
2.0 × 3.2 × 2.5
1.4 × 3.3 × 3.3
Sumida
www.sumida.com
CR32
CDRH3D16/HP
CDRH3D28
CDRH2D18/HP
10 to 47
10 to 33
10 to 47
10 to 15
3.0 × 3.8 × 4.1
1.8 × 4.0 × 4.0
3.0 × 4.0 × 4.0
2.0 × 3.2 × 3.2
Toko
www.tokoam.com
DB320C
D52LC
10 to 27
10 to 47
2.0 × 3.8 × 3.8
2.0 × 5.0 × 5.0
Würth Elektronik
www.we-online.com
WE-PD2 Typ S
WE-TPC Typ S
10 to 47
10 to 22
3.2 × 4.0 × 4.5
1.6 × 3.8 × 3.8
Coiltronics
www.cooperet.com
SD10
10 to 47
1.0 × 5.0 × 5.0
Murata
www.murata.com
LQH43C
LQH32C
10 to 47
10 to 15
2.6 × 3.2 × 4.5
1.6 × 2.5 × 3.2
be used. It is important to note that inductor saturation
current is reduced at high temperatures—see inductor
vendors for more information.
Input Capacitor
Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage ripple
at the VIN pin of the LT3470A and to force this switching
current into a tight local loop, minimizing EMI. The input
capacitor must have low impedance at the switching
frequency to do this effectively. A 1μF to 2.2μF ceramic
capacitor satisfies these requirements.
If the input source impedance is high, a larger value capacitor may be required to keep input ripple low. In this
case, an electrolytic of 10μF or more in parallel with a 1μF
ceramic is a good combination. Be aware that the input
capacitor is subject to large surge currents if the LT3470A
circuit is connected to a low impedance supply, and that
some electrolytic capacitors (in particular tantalum) must
be specified for such use.
Output Capacitor and Output Ripple
The output capacitor filters the inductor’s ripple current
and stores energy to satisfy the load current when the
LT3470A is quiescent. In order to keep output voltage
ripple low, the impedance of the capacitor must be low
at the LT3470A’s switching frequency. The capacitor’s
equivalent series resistance (ESR) determines this impedance. Choose one with low ESR intended for use in
switching regulators. The contribution to ripple voltage
due to the ESR is approximately ILIM • ESR. ESR should
be less than ~150mΩ. The value of the output capacitor
must be large enough to accept the energy stored in the
inductor without a large change in output voltage. Setting
this voltage step equal to 1% of the output voltage, the
output capacitor must be:
I
COUT > 50 • L • LIM VOUT 2
Where ILIM is the top current limit with VFB = 0V (see Electrical Characteristics). For example, an LT3470A producing
3.3V with L = 33μH requires 22μF. The calculated value
can be relaxed if small circuit size is more important than
low output ripple.
Sanyo’s POSCAP series in B-case and provides very good
performance in a small package for the LT3470A. Similar
performance in traditional tantalum capacitors requires
a larger package (C-case). With a high quality capacitor
filtering the ripple current from the inductor, the output
voltage ripple is determined by the delay in the LT3470A’s
feedback comparator. This ripple can be reduced further
by adding a small (typically 22pF) phase lead capacitor
between the output and the feedback pin.
3470afa
11
LT3470A
APPLICATIONS INFORMATION
Ceramic Capacitors
BOOST and BIAS Pin Considerations
Ceramic capacitors are small, robust and have very low
ESR. However, ceramic capacitors can cause problems
when used with the LT3470A. Not all ceramic capacitors are
suitable. X5R and X7R types are stable over temperature
and applied voltage and give dependable service. Other
types, including Y5V and Z5U have very large temperature
and voltage coefficients of capacitance. In an application
circuit they may have only a small fraction of their nominal
capacitance resulting in much higher output voltage ripple
than expected.
Capacitor C3 and the internal boost Schottky diode (see
Block Diagram) are used to generate a boost voltage that
is higher than the input voltage. In most cases a 0.22μF
capacitor will work well. Figure 2 shows two ways to arrange the boost circuit. The BOOST pin must be more than
2.5V above the SW pin for best efficiency. For outputs of
3.3V and above, the standard circuit (Figure 2a) is best.
For outputs between 2.5V and 3V, use a 0.47μF. For lower
output voltages the boost diode can be tied to the input
Ceramic capacitors are piezoelectric. The LT3470A’s
switching frequency depends on the load current, and at
light loads the LT3470A can excite the ceramic capacitor
at audio frequencies, generating audible noise. Since the
LT3470A operates at a lower current limit during Burst
Mode operation, the noise is typically very quiet to a casual ear. If this audible noise is unacceptable, use a high
performance electrolytic capacitor at the output. The input
capacitor can be a parallel combination of a 2.2μF ceramic
capacitor and a low cost electrolytic capacitor.
A final precaution regarding ceramic capacitors concerns
the maximum input voltage rating of the LT3470A. A ceramic
input capacitor combined with trace or cable inductance
forms a high quality (under damped) tank circuit. If the
LT3470A circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding
the LT3470A’s rating. This situation is easily avoided; see
the Hot-Plugging Safely section.
VIN
VIN
BOOST
C3
0.22μF
LT3470A
VOUT
SW
BIAS
GND
VBOOST – VSW ≅ VOUT
MAX VBOOST ≅ VIN + VOUT
(2a)
VIN
VIN
BOOST
C3
0.22μF
LT3470A
BIAS
SW
VOUT
GND
3470a F02
VBOOST – VSW ≅ VIN
MAX VBOOST ≅ 2•VIN
(2b)
Figure 2. Two Circuits for Generating the Boost Voltage
Table 2. Capacitor Vendors
Vendor
Phone
URL
Part Series
Comments
Panasonic
(714) 373-7366
www.panasonic.com
Ceramic,
Polymer,
Tantalum
EEF Series
Kemet
(864) 963-6300
www.kemet.com
Ceramic,
Tantalum
T494, T495
Sanyo
(408) 749-9714
www.sanyovideo.com
Ceramic,
Polymer,
Tantalum
POSCAP
Murata
(404) 436-1300
www.murata.com
Ceramic
www.avxcorp.com
Ceramic,
Tantalum
www.taiyo-yuden.com
Ceramic
AVX
Taiyo Yuden
(864) 963-6300
TPS Series
3470afa
12
LT3470A
APPLICATIONS INFORMATION
(Figure 2b). The circuit in Figure 2a is more efficient
because the BOOST pin current and BIAS pin quiescent
current comes from a lower voltage source. You must also
be sure that the maximum voltage ratings of the BOOST
and BIAS pins are not exceeded.
The LT3470A monitors the boost capacitor for sufficient
voltage such that the switch is allowed to fully saturate.
When boost voltage falls below adequate levels (1.8V
typical) the switch will operate with about 1V of drop, and
an internal current source will begin to pull 50mA (typical) from the BIAS pin which is typically connected to the
output. This current forces the LT3470A to switch more
often and with more inductor current, which recharges
Minimum Input Voltage, VOUT = 3.3V
6.0
TA = 25°C
INPUT VOLTAGE (V)
5.5
5.0
4.5
4.0
VIN TO RUN/START
3.5
3.0
0
50
100
150
200
LOAD CURRENT (mA)
250
3470a F03a
the boost capacitor. When the boost capacitor voltage is
above 1.8V (typical) the current source turns off, and the
part may enter BurstMode. This cycle will repeat anytime
there is an undervoltage condition on the boost capacitor. See Figure 3 for minimum input voltage for outputs
of 3.3V and 5V.
Shorted Input Protection
If the inductor is chosen so that it won’t saturate excessively at the top switch current limit maximum of 525mA,
an LT3470A buck regulator will tolerate a shorted output
even if VIN = 40V. There is another situation to consider
in systems where the output will be held high when the
input to the LT3470A is absent. This may occur in battery
charging applications or in battery backup systems where
a battery or some other supply is diode OR-ed with the
LT3470A’s output. If the VIN pin is allowed to float and the
SHDN pin is held high (either by a logic signal or because
it is tied to VIN), then the LT3470A’s internal circuitry will
pull its quiescent current through its SW pin. This is fine
if your system can tolerate a few mA in this state. If you
ground the SHDN pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while
the output is held high, then parasitic diodes inside the
LT3470A can pull large currents from the output through
the SW pin and the VIN pin. Figure 4 shows a circuit that
will run only when the input voltage is present and that
protects against a shorted or reversed input.
Minimum Input Voltage, VOUT = 5V
8
D1
VIN
TA = 25°C
VIN
INPUT VOLTAGE (V)
7
100k
BOOST
LT3470A
SHDN
VOUT
SW
BIAS
6
1M
VIN TO RUN/START
FB
GND
BACKUP
5
3470a F04
4
0
50
100
150
200
LOAD CURRENT (mA)
250
3470a F03b
Figure 3. The Minimum Input Voltage Depends on Output
Voltage, Load Current and Boost Circuit
Figure 4. Diode D1 Prevents a Shorted Input from Discharging
a Backup Battery Tied to the Output; It Also Protects the Circuit
from a Reversed Input. The LT3470A Runs Only When the Input is
Present Hot-Plugging Safely
3470afa
13
LT3470A
APPLICATIONS INFORMATION
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Note that large,
switched currents flow in the power switch, the internal
catch diode and the input capacitor. The loop formed by
these components should be as small as possible. Furthermore, the system ground should be tied to the regulator
ground in only one place; this prevents the switched current from injecting noise into the system ground. These
components, along with the inductor and output capacitor,
should be placed on the same side of the circuit board,
and their connections should be made on that layer. Place
a local, unbroken ground plane below these components,
and tie this ground plane to system ground at one location,
ideally at the ground terminal of the output capacitor C2.
Additionally, the SW and BOOST nodes should be kept as
small as possible. Unshielded inductors can induce noise
in the feedback path resulting in instability and increased
output ripple. To avoid this problem, use vias to route the
VOUT trace under the ground plane to the feedback divider
(as shown in Figure 5). Finally, keep the FB node as small
as possible so that the ground pin and ground traces will
shield it from the SW and BOOST nodes. Figure 5 shows
component placement with trace, ground plane and via
locations. Include vias near the GND pin, or pad, of the
LT3470A to help remove heat from the LT3470A to the
ground plane.
SHDN
VIN
GND
VOUT
3470a F05
Figure 5. A Good PCB Layout Ensures Proper, Low EMI Operation
3470afa
14
LT3470A
APPLICATIONS INFORMATION
Hot-Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LT3470A. However, these capacitors
can cause problems if the LT3470A is plugged into a live
supply (see Linear Technology Application Note 88 for
a complete discussion). The low loss ceramic capacitor
combined with stray inductance in series with the power
source forms an under damped tank circuit, and the voltage at the VIN pin of the LT3470A can ring to twice the
nominal input voltage, possibly exceeding the LT3470A’s
rating and damaging the part. If the input supply is poorly
controlled or the user will be plugging the LT3470A into an
energized supply, the input network should be designed
to prevent this overshoot. Figure 6 shows the waveforms
that result when an LT3470A circuit is connected to a 24V
supply through six feet of 24-gauge twisted pair. The first
plot is the response with a 2.2μF ceramic capacitor at the
input. The input voltage rings as high as 35V and the input
current peaks at 20A. One method of damping the tank
circuit is to add another capacitor with a series resistor to
the circuit. In Figure 6b an aluminum electrolytic capacitor
has been added. This capacitor’s high equivalent series
resistance damps the circuit and eliminates the voltage
overshoot. The extra capacitor improves low frequency
ripple filtering and can slightly improve the efficiency of the
circuit, though it is likely to be the largest component in the
circuit. An alternative solution is shown in Figure 6c. A 1Ω
resistor is added in series with the input to eliminate the
voltage overshoot (it also reduces the peak input current).
A 0.1μF capacitor improves high frequency filtering. This
solution is smaller and less expensive than the electrolytic
capacitor. For high input voltages its impact on efficiency
is minor, reducing efficiency less than one half percent for
a 5V output at full load operating from 24V.
High Temperature Considerations
The die junction temperature of the LT3470A must be
lower than the maximum rating of 125°C. This is generally
not a concern unless the ambient temperature is above
85°C. For higher temperatures, care should be taken in
the layout of the circuit to ensure good heat sinking of the
LT3470A. The maximum load current should be derated
as the ambient temperature approaches the maximum
junction rating. The die temperature is calculated by
multiplying the LT3470A power dissipation by the thermal
resistance from junction to ambient. Power dissipation
within the LT3470A can be estimated by calculating the
total power loss from an efficiency measurement. Thermal
resistance depends on the layout of the circuit board and
choice of package. The DFN package with the exposed
pad has a thermal resistance of approximately 80°C/W.
Finally, be aware that at high ambient temperatures the
internal Schottky diode will have significant leakage current
(see Typical Performance Characteristics) increasing the
quiescent current of the LT3470A converter.
3470afa
15
LT3470A
APPLICATIONS INFORMATION
CLOSING SWITCH
SIMULATES HOT PLUG
IIN
VIN
LT3470A
+
VIN
10V/DIV
2.2μF
LOW
IMPEDANCE
ENERGIZED
24V SUPPLY
IIN
10A/DIV
STRAY
INDUCTANCE
DUE TO 6 FEET
(2 METERS) OF
TWISTED PAIR
10μs/DIV
(6a)
LT3470A
10μF
35V
AI.EI.
+
VIN
10V/DIV
2.2μF
IIN
10A/DIV
10μs/DIV
(6b)
1Ω
LT3470A
0.1μF
VIN
10V/DIV
2.2μF
IIN
10A/DIV
10μs/DIV
3470a F06
(6c)
Figure 6: A Well Chosen Input Network Prevents Input Voltage Overshoot and
Ensures Reliable Operation When the LT3470A is Connected to a Live Supply
3470afa
16
LT3470A
APPLICATIONS INFORMATION
3.3V Step-Down Converter
VIN
4V TO 40V
VIN
BOOST
LT3470A
SHDN
OFF ON
C3
0.22μF, 6.3V
L1
33μH
BIAS
22pF
C1
1μF
VOUT
3.3V
250mA
SW
R1
324k
FB
GND
R2
200k
C2
22μF
3470a TA03
C1: TDK C3216JB1H105M
C2: CE JMK316 BJ226ML-T
L1: TOKO A993AS-270M=P3
5V Step-Down Converter
VIN
5.7V TO 40V
VIN
BOOST
LT3470A
OFF ON
SHDN
C3
0.22μF, 6.3V
L1
33μH
BIAS
22pF
C1
1μF
VOUT
5V
250mA
SW
R1
604k
FB
GND
R2
200k
C2
22μF
3470a TA04
C1: TDK C3216JB1H105M
C2: CE JMK316 BJ226ML-T
L1: TOKO A914BYW-330M=P3
2.5V Step-Down Converter
VIN
4V TO 40V
VIN
BOOST
LT3470A
OFF ON
SHDN
C3
0.47μF, 6.3V
L1
33μH
BIAS
22pF
C1
1μF
VOUT
2.5V
250mA
SW
R1
200k
FB
GND
R2
200k
C2
22μF
3470a TA07
C1: TDK C3216JB1H105M
C2: TDK C2012JB0J226M
L1: SUMIDA CDRH3D28
3470afa
17
LT3470A
TYPICAL APPLICATIONS
1.8V Step-Down Converter
VIN
4V TO 23V
VIN
BOOST
LT3470A
OFF ON
SHDN
VOUT
1.8V
250mA
SW
BIAS
C1
1μF
C3
0.22μF, 25V
L1
22μH
22pF
R1
147k
FB
GND
R2
332k
C2
22μF
3470a TA05
C1: TDK C3216JB1H105M
C2: TDK C2012JB0J226M
L1: MURATA LQH32CN150K53
12V Step-Down Converter
VIN
15V TO 34V
VIN
BOOST
LT3470A
OFF ON
SHDN
C3
0.22μF, 16V
L1
33μH
BIAS
22pF
C1
1μF
VOUT
12V
250mA
SW
R1
866k
FB
GND
R2
100k
C2
10μF
3470a TA06
C1: TDK C3216JB1H105M
C2: TDK C3216JB1C106M
L1: MURATA LQH32CN150K53
3470afa
18
LT3470A
PACKAGE DESCRIPTION
DDB Package
8-Lead Plastic DFN (3mm × 2mm)
(Reference LTC DWG # 05-08-1702 Rev B)
0.61 ±0.05
(2 SIDES)
3.00 ±0.10
(2 SIDES)
R = 0.115
TYP
5
R = 0.05
TYP
0.40 ± 0.10
8
0.70 ±0.05
2.55 ±0.05
1.15 ±0.05
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
2.20 ±0.05
(2 SIDES)
PIN 1 BAR
TOP MARK
(SEE NOTE 6)
0.200 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
2.00 ±0.10
(2 SIDES)
0.56 ± 0.05
(2 SIDES)
0.75 ±0.05
0 – 0.05
4
0.25 ± 0.05
1
PIN 1
R = 0.20 OR
0.25 × 45°
CHAMFER
(DDB8) DFN 0905 REV B
0.50 BSC
2.15 ±0.05
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING CONFORMS TO VERSION (WECD-1) IN JEDEC PACKAGE OUTLINE M0-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
3470afa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT3470A
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1616
25V, 500mA (IOUT), 1.4MHz, High Efficiency
Step-Down DC/DC Converter
VIN = 3.6V to 25V, VOUT = 1.25V, IQ = 1.9mA, ISD = <1μA,
ThinSOT Package
LT1676
60V, 440mA (IOUT), 100kHz, High Efficiency
Step-Down DC/DC Converter
VIN = 7.4V to 60V, VOUT = 1.24V, IQ = 3.2mA, ISD = 2.5μA,
S8 Package
LT1765
25V, 2.75A (IOUT), 1.25MHz, High Efficiency
Step-Down DC/DC Converter
VIN = 3V to 25V, VOUT = 1.2V, IQ = 1mA, ISD = 15μA,
S8, TSSOP16E Packages
LT1766
60V, 1.2A (IOUT), 200kHz, High Efficiency
Step-Down DC/DC Converter
VIN = 5.5V to 60V, VOUT = 1.2V, IQ = 2.5mA, ISD = 25μA,
TSSOP16/E Package
LT1767
25V, 1.2A (IOUT), 1.25MHz, High Efficiency
Step-Down DC/DC Converter
VIN = 3V to 25V; VOUT = 1.2V, IQ = 1mA, ISD = 6μA,
MS8/E Packages
LT1776
40V, 550mA (IOUT), 200kHz, High Efficiency
Step-Down DC/DC Converter
VIN = 7.4V to 40V; VOUT = 1.24V, IQ = 3.2mA, ISD = 30μA,
N8, S8 Packages
LTC®1877
600mA (IOUT), 550kHz, Synchronous
Step-Down DC/DC Converter
VIN = 2.7V to 10V; VOUT = 0.8V, IQ = 10μA, ISD = <1μA,
MS8 Package
LTC1879
1.2A (IOUT), 550kHz, Synchronous
Step-Down DC/DC Converter
VIN = 2.7V to 10V; VOUT = 0.8V, IQ = 15μA, ISD = <1μA,
TSSOP16 Package
LT1933
36V, 600mA, 500kHz, High Efficiency
Step-Down DC/DC Converter
VIN = 3.6V to 36V; VOUT = 1.25V, IQ = 2.5μA, ISD = <1μA,
ThinSOT and 2mm × 3mm DFN-6 Package
LT1934
34V, 250mA (IOUT), Micropower, Step-Down
DC/DC Converter
VIN = 3.2V to 34V; VOUT = 1.25V, IQ = 12μA, ISD = <1μA,
ThinSOT and 2mm × 3mm DFN-6 Package
LT1956
60V, 1.2A (IOUT), 500kHz, High Efficiency
Step-Down DC/DC Converter
VIN = 5.5V to 60V, VOUT = 1.2V, IQ = 2.5mA, ISD = 25μA,
TSSOP16/E Package
LTC3405/LTC3405A
300mA (IOUT), 1.5MHz, Synchronous
Step-Down DC/DC Converter
VIN = 2.7V to 6V, VOUT = 0.8V, IQ = 20μA, ISD = <1μA,
ThinSOT Package
LTC3406/LTC3406B
600mA (IOUT), 1.5MHz, Synchronous
Step-Down DC/DC Converter
VIN = 2.5V to 5.5V, VOUT = 0.6V, IQ = 20μA, ISD = <1μA,
ThinSOT Package
LTC3411
1.25A (IOUT), 4MHz, Synchronous
Step-Down DC/DC Converter
VIN = 2.5V to 5.5V, VOUT = 0.8V, IQ = 60μA, ISD = <1μA,
MS Package
LTC3412
2.5A (IOUT), 4MHz, Synchronous
Step-Down DC/DC Converter
VIN = 2.5V to 5.5V, VOUT = 0.8V, IQ = 60μA, ISD = <1μA,
TSSOP16E Package
LT3430
60V, 2.75A (IOUT), 200kHz, High Efficiency
Step-Down DC/DC Converter
VIN = 5.5V to 60V, VOUT = 1.2V, IQ = 2.5mA, ISD = 30μA,
TSSOP16E Package
LT3470
40V, 200mA, Micropower Step-Down DC/DC Converter
VIN = 4V to 40V, VOUT = 1.25V, IQ = 35μA, ISD = <1μA, DFN-8,
ThinSOT Packages
3470afa
20 Linear Technology Corporation
LT 1108 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2008