NCV7425 LIN Transceiver with Voltage Regulator and Reset Pin General Description The NCV7425 is a fully featured local interconnect network (LIN) transceiver designed to interface between a LIN protocol controller and the physical bus. The NCV7425 LIN device is a member of the in−vehicle networking (IVN) transceiver family of ON Semiconductor that integrates a LIN v2.1 physical transceiver and a low−drop voltage regulator. It is designed to work in harsh automotive environment and is submitted to the TS16949 qualification flow. The LIN bus is designed to communicate low rate data from control devices such as door locks, mirrors, car seats, and sunroofs at the lowest possible cost. The bus is designed to eliminate as much wiring as possible and is implemented using a single wire in each node. Each node has a slave MCU−state machine that recognizes and translates the instructions specific to that function. The main attraction of the LIN bus is that all the functions are not time critical and usually relate to passenger comfort. http://onsemi.com MARKING DIAGRAM 16 SOIC−16 LEAD WIDE BODY EXPOSED PAD CASE 751AG 16 NCV7425−x AWLYYWWG 1 x A WL YY WW G 1 = 0 or 5 = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 19 of this data sheet. Features • LIN−Bus Transceiver LIN compliant to specification revision 2.1 (backward compatible to versions 2.0 and 1.3) and J2602 ♦ Bus Voltage ±45 V ♦ Transmission Rate up to 20 kBaud ♦ Integrated Slope Control for Improved EMI Compatibility Package ♦ SOIC−16 Wide Body Green Package with Exposed Pad Protection ♦ Thermal Shutdown ♦ Indefinite Short−Circuit Protection on Pins LIN and WAKE Towards Supply and Ground ♦ Load Dump Protection (45 V) ♦ Bus Pins Protected Against Transients in an Automotive Environment ♦ ESD Protection Level for LIN, INH, WAKE and VBB up to ±10 kV Voltage Regulator ♦ Two Device Versions: Output Voltage 3.3 V or 5 V For Loads up to 150 mA ♦ • • • © Semiconductor Components Industries, LLC, 2012 May, 2012 − Rev. 1 Under−Voltage Detector with a Reset Output to the Supplied Microcontroller ♦ INH Output for Auxiliary Purposes (switching of an external pull−up or resistive divider towards battery, control of an external voltage regulator etc.) Modes ♦ Normal Mode: LIN Communication in Either Low (up to 10 kBaud) or Normal Slope ♦ Sleep Mode: VCC is Switched “off” and No Communication on LIN Bus ♦ Stand−by Mode: VCC is Switched “on” but There is No Communication on LIN Bus ♦ Wake−up Bringing the Component From Sleep Mode Into Standby Mode is Possible Either by LIN Command or Digital Input Signal on WAKE Pin Wake−up from LIN Bus can also be Detected and Flagged When the Chip is Already in Standby Mode These are Pb−Free Devices ♦ • • Typical Applications • Automotive • Industrial Networks 1 Publication Order Number: NCV7425/D NCV7425 Table 1. KEY TECHNICAL CHARACTERISTICS Symbol Parameter Min Typ Max Unit 5 12 28 V 3.3 V VERSION VBB Nominal battery operating voltage VBB Load dump protection (Note 1) 45 V IBB_SLP Supply current in sleep mode 20 mA VCC_OUT (Note 2) Regulated VCC output in normal mode, VCC load 0−100 mA 3.234 3.3 3.366 V Regulated VCC output in normal mode, 100 mA < VCC load < 150 mA 3.201 3.3 3.399 IOUT_LIM VCC regulator current limitation 150 225 300 mA 0 VBB V −45 45 0 VBB V VWAKE Operating DC voltage on WAKE pin Maximum rating voltage on WAKE pin VINH Operating DC voltage on INH pin TJ_tsd Junction thermal shutdown temperature 165 195 °C Operating junction temperature −40 +150 °C 28 V TJ 5 V VERSION VBB Nominal battery operating voltage 6 12 VBB Load dump protection (Note 1) 45 V IBB_SLP Supply current in sleep mode 20 mA 5 5.10 V VCC_OUT (Note 2) Regulated VCC output in normal mode, VCC load 0−100 mA 4.90 Regulated VCC output in normal mode, 100 mA < VCC load < 150 mA 4.85 5 5.15 V IOUT_LIM VCC regulator current limitation 150 225 300 mA 0 VBB V −45 45 0 VBB V Junction thermal shutdown temperature 165 195 °C Operating junction temperature −40 +150 °C VWAKE Operating DC voltage on WAKE pin Maximum rating voltage on WAKE pin VINH TJ_TSD TJ Operating DC voltage on INH pin 1. The applied transients shall be in accordance with ISO 7637 part 1, test pulse 5. The device complies with functional class C;. The LIN communication itself complies with functional class B. On regulator class A can be reached depending on the application and external components 2. VCC voltage must be properly stabilized by external capacitors: capacitor of min. 80 nF with ESR < 10 mW in parallel with a capacitor of min. 8 mF, ESR < 1 W. Table 2. THERMAL CHARACTERISTICS Conditions Value Unit Rth(vj−a)_1 Symbol Thermal resistance junction−to−ambient on JEDEC 1S0P PCB Free Air 138 K/W Rth(vj−a)_2 Thermal resistance junction−to−ambient on JEDEC 1S0P + 300 mm2 PCB Free Air 94 K/W Rth(vj−a)_3 Thermal resistance junction−to−ambient on JEDEC 2S2P PCB Free Air 70 K/W Free Air 49 K/W Rth(vj−a)_4 Parameter Thermal resistance junction−to−ambient on JEDEC 2S2P + 300 http://onsemi.com 2 mm2 PCB NCV7425 V CC V BB INH NCV7425 Band− gap V−reg VBB WAKE VCC VBB POR VCC STB Thermal shutdown EN Control Logic Osc VCC VBB TxD VCC RxD Receiver LIN VCC RSTN Timeout Slope Control GND OTP _ZAP TEST PD20090609 .1 Figure 1. Block Diagram TYPICAL APPLICATION Application Information VCC voltage must be properly stabilized by external capacitors: capacitor of min. 80 nF (ESR < 10 mW) in parallel with a capacitor of min. 8 mF (ESR < 1 W). The 10 mF capacitor on the battery is optional and serves as reservoir capacitor to deal with battery supply micro−cuts. The EMC immunity of the Master−mode device can be further enhanced by adding a capacitor between the LIN output and ground. The optimum value of this capacitor is determined by the length and capacitance of the LIN bus, the number and capacitance of Slave devices, the pull−up resistance of all devices (Master and Slave), and the required time constant of the system, respectively. Master Node 10uF 100nF V BB VCC WAKE OTP_ZAP GND 100nF 10uF VCC V BB VCC TxD LIN EN LIN controller STB TEST VCC TxD Micro 220 pF EN 100nF RxD INH WAKE RSTN WAKE 10nF GND NCV 7425 1kW 1 nF LIN 10uF VBAT RxD INH LIN Slave Node 100nF GND GND Micro controller STB RSTN WAKE 10nF 10uF VBAT OTP_ZAP GND TEST GND PD20090609.2 KL30 LIN−BUS KL31 Figure 2. Application Diagram http://onsemi.com 3 NCV7425 1 16 LIN 2 15 RxD GND 3 14 TxD GND 4 13 RSTN WAKE 5 12 STB INH 6 11 EN OTP_SUP 7 10 TEST n.c. 8 9 n.c. NCV7425 VBB VCC Figure 3. Pin Assignment Table 3. PIN FUNCTION DESCRIPTION Pin Number Pin Name Description 1 VBB Battery supply input 2 LIN LIN bus output/input 3 GND Ground 4 GND Ground 5 WAKE 6 INH 7 OTP_SUP 8 n.c. not connected 9 n.c. not connected 10 TEST High voltage digital input pin to switch the part from sleep− to standby mode Inhibit output Supply for programming of trimming bits at factory testing, needs to be grounded in the application Digital input for factory testing, needs to be grounded in the application 11 EN Enable input for mode control 12 STB Standby mode control input 13 RSTN 14 TxD Transmit data input, low in dominant state 15 RxD Receive data output; low in dominant state; push−pull output 16 VCC Voltage regulator output Reset output; open−drain output with an on−chip pull−up resistor FUNCTIONAL DESCRIPTION Overall Functional Description with EMC performance due to reduced slew rate of the LIN output. The junction temperature is monitored via a thermal shutdown circuit that switches the LIN transmitter and voltage regulator off when temperature exceeds the TSD trigger level. NCV7425 has four operating states (normal mode, low slope mode, stand−by mode, and sleep mode) that are determined by the input signals EN, WAKE, STB, and TxD. LIN is a serial communication protocol that efficiently supports the control of mechatronic nodes in distributed automotive applications. The domain is class−A multiplex buses with a single master node and a set of slave nodes. NCV7425 is designed as a master or slave node for the LIN communication interface with an integrated 3.3 V or 5 V voltage regulator having a current capability up to 150 mA for supplying any external components (microcontroller, CAN node, etc.). NCV7425 contains the LIN transmitter, LIN receiver, voltage regulator, power−on−reset (POR) circuits and thermal shutdown (TSD). The LIN transmitter is optimized for the maximum specified transmission speed of 20 kBaud Operating States NCV7425 provides four operating states, two modes for normal operation with communication, one stand−by without communication and one low power mode with very low current consumption − see Figure 4 and Table 4. http://onsemi.com 4 NCV7425 Table 4. MODE SELECTION LIN Transceiver 30 kW on LIN RSTN High if STB = High during state transition; Floating otherwise Normal Slope ON High Low = Dominant State High = Recessive State High if STB = High during state transition; Floating otherwise Low Slope ON High ON Low after LIN wake−up, high otherwise (Note 6) Floating OFF OFF Controlled by VCC under−voltage monitor OFF Clamped to VCC (Note 6) Floating OFF OFF Low Mode VCC RxD INH Normal − Slope (Note 3) ON Low = Dominant State High = Recessive State Normal − Low Slope (Note 4) ON Stand−by (Note 5) Sleep 3. The normal slope mode is entered when pin EN goes HIGH while TxD is in HIGH state during EN transition. 4. The low slope mode is entered when pin EN goes HIGH while TxD is in LOW state during EN transition. LIN transmitter gets on only after TxD returns to high after the state transition. 5. The stand−by mode is entered automatically after power−up. 6. In Stand−by and Sleep mode, the High state is achieved by internal pull−up resistor to VCC. Standby mode EN changes 1−>0 while STB=1 VCC under−voltage VCC under−voltage EN changes 1−>0 while STB=1 EN changes 0−>1 while TxD=1 Normal mode (low slope ) − VCC: on −LIN TRX: on −INH: High/floating −LIN term.: 30kW −RxD pin: LIN data −RSTN pin: High Normal mode (normal slope ) − VCC: on −LIN TRX: on −INH: High/floating −LIN term.: 30kW −RxD pin: LIN data −RSTN pin: High EN changes 1−>0 while STB=0 EN changes 0−>1 while TxD=0 VBB power−up − VCC: on −LIN TRX: off −INH: floating −LIN term.: current source −RxD pin: High/Low −RSTN pin: VCC_UV Sleep mode EN changes 1−>0 while STB=0 − VCC: off −LIN TRX: off −INH: floating −LIN term.: current source −RxD pin: at VCC −RSTN pin: Low PD20090610 .01 Figure 4. State Diagram Normal Slope Mode The mode selection is done by EN=HIGH when TxD pin is HIGH. If STB pin is high during the standby−to−normal slope mode transition, INH pin is pulled high. Otherwise, it stays floating. In normal slope mode the transceiver can transmit and receive data via LIN bus with speed up to 20 kBaud. The transmit data stream of the LIN protocol is present on the TxD pin and converted by the transmitter into a LIN bus signal with controlled slew rate to minimize EMC emission. The receiver consists of the comparator that has a threshold with hysteresis in respect to the supply voltage and an input filter to remove bus noise. The LIN output is pulled HIGH via an internal 30 kW pull−up resistor. For master applications it is needed to put an external 1 kW resistor with a serial diode between LIN and VBB (or INH) − see Figure 2. Low Slope Mode In low slope mode the slew rate of the signal on the LIN bus is reduced (rising and falling edges of the LIN bus signal are longer). This further reduces the EMC emission. As a consequence the maximum speed on the LIN bus is reduced up to 10 kBaud. This mode is suited for applications where the communication speed is not critical. The mode selection http://onsemi.com 5 NCV7425 Sleep Mode is done by EN=HIGH when TxD pin is LOW. In order not to transmit immediately a dominant state on the bus (because TxD = LOW), the LIN transmitter is enabled only after TxD returns to HIGH. If STB pin is high during the standby−to−low slope mode transition, INH pin is pulled high. Otherwise, it stays floating. The Sleep Mode provides extremely low current consumption. This mode is entered when both EN and STB pins are LOW coming from normal mode. The internal termination resistor of 30 kW between LIN and VBB is disconnected and also the VCC regulator is switched off to minimize current consumption. Stand−by Mode Wake−up The stand−by mode is always entered after power−up of the NCV7425. It can also be entered from normal mode when the EN pin is low and the stand−by pin is high. From sleep mode it can be entered after a local wake−up or LIN wakeup. In stand−by mode the VCC voltage regulator for supplying external components (e.g. a microcontroller) stays active. Also the LIN receiver stays active to be able to detect a remote wake−up via bus. The LIN transmitter is disabled and the slave internal termination resistor of 30 kW between LIN and VBB is disconnected in order to minimize current consumption. Only a pull−up current source between VBB and LIN is active. Wake NCV7425 has two possibilities to wake−up from sleep or stand−by mode (see Figure 4): Local wake−up: enables the transition from sleep mode to stand−by mode Remote wake−up via LIN: enables the transition from sleep− to stand−by mode and can be also detected when already in standby mode. A local wake−up is only detected in sleep mode if a transition from LOW to HIGH or from HIGH to LOW is seen on the wake pin. Detection of Local Wake−Up Wake VBB Detection of Local Wake−Up VBB 50% VBB typ. Sleep Mode t Stand−by Mode 50% VBB typ. Sleep Mode Figure 5. Local Wake−Up Signal A remote wake−up is only detected if a combination of (1) a falling edge at the LIN pin (transition from recessive to dominant) is followed by (2) a dominant level maintained Stand−by Mode t PC20060427.3 for a time period > tWAKE and (3) again a rising edge at pin LIN (transition from dominant to recessive) happens. LIN Detection of Remote Wake−Up VBB LIN recessive level tWAKE 60% VBB 40% VBB LIN dominant level Sleep Mode Stand−by Mode t PC20060427.2 Figure 6. Remote Wake−Up Behavior VCC Under−voltage Detection and RSTN Pin The wake−up source is distinguished by pin RxD in the stand−by mode: RxD remains HIGH after power−up or local wake−up. RxD is kept LOW until normal mode is entered after a remote wake−up (LIN) In standby, normal and low−slope modes, the VCC regulator is monitored. Whenever the regulator output falls below VCC_UV_THR level (typically 90% of the nominal voltage) for longer than VCC_UV_deb (typically 5 ms), an http://onsemi.com 6 NCV7425 In the sleep mode, RSTN pin is kept Low regardless the VCC level − it means that RSTN becomes Low immediately at sleep mode entry even if the VCC capacitor is still charged. In all situations where RSTN pin is kept Low, the digital inputs to NCV7425 are discarded by the internal control logic and have no effect on its behavior. The RSTN pin function is illustrated in Figure 7. under−voltage is detected. Output pin RSTN is pulled to Low level to indicate the under−voltage condition to the external load (a microcontroller). At the same time, the device enters automatically the standby mode. As soon as the regulator output returns above the under−voltage level, the RSTN Low level is extended by typically 6ms and only then released to High level in order to ensure microcontroller initialization under correct supply conditions. Figure 7. RSTN Pin Behavior http://onsemi.com 7 NCV7425 ELECTRICAL CHARACTERISTICS Definitions All voltages are referenced to GND. Positive currents flow into the IC. Table 5. ABSOLUTE MAXIMUM RATINGS − 3.3 V and 5 V VERSIONS Symbol Parameter Min. Max. Unit −0.3 +45 V 0 +6 V VBB Battery voltage on pin VBB (Note 7) VCC DC voltage on pin VCC IVCC Current delivered by the VCC regulator 150 VLIN LIN bus voltage (Note 8) −45 +45 V VINH DC voltage on inhibit pin −0.3 VBB + 0.3 V VWAKE Voltage on WAKE pin −45 45 V VDig_IO DC voltage on pins TxD, RxD, EN, STB, RSTN −0.3 VCC + 0.3 V Maximum junction temperature −40 +165 °C Electrostatic discharge voltage (INH, WAKE and VBB) system Human Body Model (HBM) (Note 9) −10 +10 kV Electrostatic discharge voltage (LIN pin, no external capacitor) HBM (Note 9) −10 +10 Electrostatic discharge voltage (LIN pin, 220 pF) System HBM (Note 9) −15 +15 Electrostatic discharge voltage (pins LIN, INH, WAKE and VBB) HBM (Note 10) −8 +8 Electrostatic discharge voltage (other pins) HBM (Note 10) −4 +4 −250 +250 TJ Vesd Electrostatic discharge voltage; charge device model (Note 11) mA V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 7. The applied transients shall be in accordance with ISO 7637 part 1, test pulses 1, 2, 3a, 3b, and 5. The device complies with functional class C; class A can be reached depending on the application and external components. 8. The applied transients shall be in accordance with ISO 7637 part 1, test pulses 1, 2, 3a, and 3b. The device complies with functional class C; class A can be reached depending on the application and external components. 9. Equivalent to discharging a 150 pF capacitor through a 330 W resistor conform to IEC Standard 61000−4−2. The specified values are verified by external test house. 10. Equivalent to discharging a 100 pF capacitor through a 1.5 kW resistor conform to MIL STD 883 method 3015.7. 11. Conform to EOS/ESD−DS5.3 (socket mode). Table 6. DC CHARACTERISTICS − 3.3 V VERSION VBB = 5 V to 28 V; TJ = −40°C to +150°C; unless otherwise specified. Parameter Symbol Conditions Min Typ Max Unit DC CHARACTERISTICS SUPPLY − PINS VBB AND VCC IBB_ON Supply current Normal mode; LIN recessive 1.6 mA IBB_STB Supply current Stand−by mode, VBB = 5 − 18 V, TJ < 105°C 60 mA IBB_SLP Supply current Sleep mode, VBB = 5 − 18 V, TJ < 105°C 20 mA V DC CHARACTERISTICS − VOLTAGE REGULATOR VCC_OUT Regulator output voltage VCC load 0 − 100 mA 3.234 3.30 3.366 100 mA < VCC load < 150 mA 3.201 3.30 3.399 12. Measured at output voltage VCC_OUT = (VCC_OUT @ VBB = 5 V) − 2%. 13. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull up resistor. The drop at the switch is negligible. See Figure 2. 14. Guaranteed by design. Not tested http://onsemi.com 8 NCV7425 Table 6. DC CHARACTERISTICS − 3.3 V VERSION VBB = 5 V to 28 V; TJ = −40°C to +150°C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Over−current limitation 150 225 300 mA Under−voltage detection threshold 2.80 2.97 3.13 V DC CHARACTERISTICS − VOLTAGE REGULATOR IOUT_LIM VCC_UV_THR DVCC_OUT Vdo Line Regulation VBB 5 − 28 V, Iout = 5 mA TJ = 25°C 0.41 Load Regulation Iout 1−100 mA, VBB = 14 V, TJ = 25°C 25 Dropout Voltage (VBB − VCC_OUT) (Note 12) Figure 12 Iout = 10 mA, TJ = 25°C 22 Iout = 50 mA, TJ = 25°C 108 Iout = 100 mA, TJ = 25°C 216 mV mV DC CHARACTERISTICS − LIN TRANSMITTER VLIN_dom_LoSup LIN dominant output voltage TxD = low; VBB = 7.3 V 1.2 V VLIN_dom_HiSup LIN dominant output voltage TxD = low; VBB = 18 V 2.0 V 1 V Vser_diode LIN Voltage drop at serial diode (Note 13) ILIN_lim Short circuit current limitation Rslave Internal pull−up resistance CLIN TxD = high; ILIN = 10 mA 0.3 VLIN = VBB(max) 40 20 Capacitance on pin LIN (Note 14) ILIN_off_dom LIN output current bus in dominant state Driver off; VBB = 12 V ILIN_off_rec LIN output current bus in recessive state Driver off; VBB < 18 V, VBB < VLIN < 18 V ILIN_no_GND Communication not affected VBB = GND = 12 V; 0 < VLIN < 18 V ILIN_no_VBB LIN bus remains operational VBB = GND = 0 V; 0 < VLIN < 18 V 200 mA 33 47 kW 25 35 pF −1 mA −1 1 mA 1 mA 5 mA 0.4 VBB DC CHARACTERISTICS − LIN RECEIVER VBUS_dom bus voltage for dominant state VBUS_rec bus voltage for recessive state Vrec_dom Receiver threshold LIN bus recessive → dominant 0.4 0.6 VBB Vrec_rec Receiver threshold LIN bus dominant → recessive 0.4 0.6 VBB Vrec_cnt Receiver centre voltage (VBUS_dom + VBUS_rec) / 2 0.475 0.525 VBB Vrec_hys Receiver hysteresis 0.05 0.175 VBB 0.35 0.65 VBB 1 mA 54 ms 0.8 V 0.6 VBB DC CHARACTERISTICS − DIGITAL I/O PINS PIN WAKE VWAKE_TH Ileak TWAKE(min) Threshold voltage Input leakage current Debounce time VWAKE = 0 V; VBB = 18 V −1 Sleep mode; rising and falling edge 8 −0.5 PINS TxD AND STB Vil Low level input voltage 12. Measured at output voltage VCC_OUT = (VCC_OUT @ VBB = 5 V) − 2%. 13. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull up resistor. The drop at the switch is negligible. See Figure 2. 14. Guaranteed by design. Not tested http://onsemi.com 9 NCV7425 Table 6. DC CHARACTERISTICS − 3.3 V VERSION VBB = 5 V to 28 V; TJ = −40°C to +150°C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit DC CHARACTERISTICS − DIGITAL I/O PINS PINS TxD AND STB Vih High level input voltage 2.0 Rpu Pull−up resistance to VCC 50 V 200 kW 0.75 V 1 mA 0.8 V PIN INH Delta_VH Ileak High level voltage drop IINH = 15 mA Leakage current Sleep mode; VINH = 0 V 0.35 −1 PIN EN Vil Low level input voltage Vih High level input voltage 2.0 Rpd Pull−down resistance to ground 50 V 200 kW 0.65 V PIN RxD Vol Low level output voltage Isink = 2 mA Voh High level output voltage (In Normal mode) Normal mode, Isource = −2 mA Rpu Pull−up resistance to VCC (In Standby and Sleep mode) Standby mode, Sleep mode VCC − 0.65 V 10 kW PIN RSTN Vol Low level output voltage Rpu Pull−up resistance to VCC Isink = 2 mA 0.65 V 200 kW 4.5 V 3.8 V 2 V/ms 165 195 °C 9 18 °C 50 DC CHARACTERISTICS POWER−ON RESET PORH_VBB VBB POR high level detection threshold PORL_VBB VBB POR low level detection threshold POR_VBB_sl Maximum slope on VBB to guarantee POR 1.7 THERMAL SHUTDOWN TJ_tsd Junction temperature TJ_hyst Thermal shutdown hysteresis For shutdown 12. Measured at output voltage VCC_OUT = (VCC_OUT @ VBB = 5 V) − 2%. 13. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull up resistor. The drop at the switch is negligible. See Figure 2. 14. Guaranteed by design. Not tested http://onsemi.com 10 NCV7425 Table 7. DC CHARACTERISTICS − 5 V VERSION VBB = 6 V to 28 V; TJ = −40°C to +150°C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit DC CHARACTERISTICS SUPPLY − PINS VBB AND VCC IBB_ON Supply current Normal mode; LIN recessive 1.6 mA IBB_STB Supply current Stand−by mode, VBB = 6 − 18 V, TJ < 105°C 60 mA IBB_SLP Supply current Sleep mode, VBB = 6 − 18V, TJ < 105°C 20 mA DC CHARACTERISTICS − VOLTAGE REGULATOR VCC_OUT IOUT_LIM VCC_UV_THR DVCC_OUT Vdo Regulator output voltage VCC load 0 − 100 mA 4.9 5 5.1 V 100 mA < VCC load < 150 mA 4.85 5 5.15 V Over−current limitation 150 225 300 mA Under−voltage detection threshold 4.25 4.5 4.75 V Line Regulation VBB 6 − 28 V, Iout = 5 mA TJ = 25°C 0.41 mV Load Regulation Iout 1 − 100 mA, VBB = 14 V, TJ = 25°C 22 mV Iout = 10 mA, TJ = 25°C 22 mV Iout = 50 mA, TJ = 25°C 108 mV Iout = 100 mA, TJ = 25°C 216 mV Dropout Voltage (VBB − VCC_OUT) (Note 15) (Figure 20) DC CHARACTERISTICS LIN TRANSMITTER VLIN_dom_LoSup LIN dominant output voltage TxD = low; VBB = 7.3 V 1.2 V VLIN_dom_HiSup LIN dominant output voltage TxD = low; VBB = 18 V 2.0 V Vser_diode LIN Voltage drop at serial diode (Note 16) ILIN_lim Short circuit current limitation Rslave Internal pull−up resistance CLIN TxD = high; ILIN = 10 mA 0.3 1 V VLIN = VBB(max) 40 200 mA 33 47 kW 25 35 pF 20 Capacitance on pin LIN (Note 17) ILIN_off_dom LIN output current bus in dominant state Driver off; VBB = 12 V ILIN_off_rec LIN output current bus in recessive state Driver off; VBB < 18 V, VBB < VLIN < 18 V ILIN_no_GND Communication not affected VBB = GND = 12 V; 0 < VLIN < 18 V ILIN_no_VBB LIN bus remains operational VBB = GND = 0 V; 0 < VLIN < 18 V −1 −1 mA 1 mA 1 mA 5 mA 0.4 VBB DC CHARACTERISTICS LIN RECEIVER VBUS_dom bus voltage for dominant state VBUS_rec bus voltage for recessive state Vrec_dom Receiver threshold LIN bus recessive → dominant Vrec_rec Receiver threshold LIN bus dominant → recessive Vrec_cnt Receiver center voltage (VBUS_dom + VBUS_rec) / 2 Vrec_hys Receiver hysteresis 0.05 0.6 0.4 VBB 0.6 VBB 0.4 0.6 VBB 0.475 0.525 VBB 0.175 VBB 15. Measured at output voltage VCC_OUT = (VCC_OUT @ VBB = 6 V) − 2%. 16. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull up resistor. The drop at the switch is negligible. See Figure 2. 17. Guaranteed by design. Not tested http://onsemi.com 11 NCV7425 Table 7. DC CHARACTERISTICS − 5 V VERSION VBB = 6 V to 28 V; TJ = −40°C to +150°C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 0.65 VBB 1 mA 54 ms 0.8 V 200 kW 0.75 V 1 mA 0.8 V DC CHARACTERISTICS − DIGITAL I/O PINS PIN WAKE VWAKE_TH Ileak TWAKE_MIN Threshold voltage Input leakage current Debounce time 0.35 VWAKE = 0 V; VBB = 18 V −1 Sleep mode; rising and falling edge 8 −0.5 PINS TxD AND STB Vil Low level input voltage Vih High level input voltage 2.0 Rpu Pull−up resistance to VCC 50 V PIN INH Delta_VH I_leak High level voltage drop Leakage current IINH = 15 mA Sleep mode; VINH = 0 V 0.35 −1 PIN EN Vil Low level input voltage Vih High level input voltage 2.0 Rpd Pull−down resistance to ground 50 V 200 kW 0.65 V PIN RxD Vol Low level output voltage Isink = 2 mA Voh High level output voltage (In Normal mode) Normal mode, Isource = −2 mA Rpu Pull−up resistance to VCC (In Standby and Sleep mode) VCC − 0.65 Standby mode, Sleep mode V 10 kW PIN RSTN Vol Low level output voltage Rpu Pull−up resistance to VCC Isink = 2 mA 0.65 V 200 kW 4.5 V 3.8 V 2 V/ms 165 195 °C 9 18 °C 50 DC CHARACTERISTICS POWER−ON RESET PORH_VBB VBB POR high level detection threshold PORL_VBB VBB POR low level detection threshold POR_VBB_sl Maximum slope on VBB to guarantee POR 1.7 THERMAL SHUTDOWN TJ_tsd Junction temperature TJ_hyst Thermal shutdown hysteresis For shutdown 15. Measured at output voltage VCC_OUT = (VCC_OUT @ VBB = 6 V) − 2%. 16. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull up resistor. The drop at the switch is negligible. See Figure 2. 17. Guaranteed by design. Not tested http://onsemi.com 12 NCV7425 Table 8. AC CHARACTERISTICS − 3.3 V AND 5 V VERSIONS VBB = 7 V to 18 V; TJ = −40°C to +150°C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit AC CHARACTERISTICS LIN TRANSMITTER D1 Duty Cycle 1 = tBUS_rec(min) / (2 x TBit) see Figure 24 normal slope mode THrec(max) = 0.744 x VBB THdom(max) = 0.581 x VBB TBit = 50 ms VBB = 7 V to 18 V 0.396 0.5 D2 Duty Cycle 2 = tBUS_rec(max) / (2 x TBit) see Figure 24 normal slope mode THrec(min) = 0.422 x VBB THdom(min) = 0.284 x VBB TBit = 50 ms VBB = 7.6 V to 18 V 0.5 0.581 D3 Duty Cycle 3 = tBUS_rec(min) / (2 x Tbit) see Figure 24 normal slope mode THrec(max) = 0.778 x VBB THdom(max) = 0.616 x VBB TBit = 96 ms VBB = 7 V to 18 V 0.417 0.5 D4 Duty Cycle 4 = tBUS_rec(max) / (2 x Tbit) see Figure 24 normal slope mode THrec(min) = 0.389 x VBB THdom(min) = 0.251 x VBB TBit = 96 ms VBB = 7.6 V to 18 V 0.5 0.590 Tfall_norm LIN falling edge Normal slope mode; VBB = 12 V; L1, L2 (Note 18) 22.5 ms Trise_norm LIN rising edge Normal slope mode; VBB = 12 V; L1, L2 (Note 18) 22.5 ms Tsym_norm LIN slope symmetry Normal slope mode; VBB = 12 V; L1, L2 (Note 18) 4 ms Tfall_norm LIN falling edge Normal slope mode; VBB = 12 V; L3 (Note 18) 27 ms Trise_norm LIN rising edge Normal slope mode; VBB = 12 V; L3 (Note 18) 27 ms Tsym_norm LIN slope symmetry Normal slope mode; VBB = 12 V; L3 (Note 18) 5 ms Tfall_low LIN falling edge Low slope mode (Note 19); VBB = 12 V; L3 (Note 18) 62 ms Trise_low LIN rising edge Low slope mode (Note 19); VBB = 12 V; L3 (Note 18) 62 ms TWAKE Dominant time−out for wake−up via LIN bus 30 150 ms Tdom TxD dominant time−out 6 20 ms VCC_UV_deb VCC under−voltage detection debounce time 1.5 5 10 ms RSTN_ext Extension time of RSTN Low pulse beyond VCC under−voltage 3 6 10 ms TxD = low −4 −5 AC CHARACTERISTICS LIN RECEIVER Trec_prop_down Propagation delay of receiver falling edge 0.1 6 ms Trec_prop_up Propagation delay of receiver rising edge 0.1 6 ms Trec_sym Propagation delay symmetry −2 2 ms Trec_prop_down − Trec_prop_up 18. The AC parameters are specified for following RC loads on the LIN bus: L1 = 1 kW / 1 nF; L2 = 660 W / 6.8 nF; L3 = 500 W / 10 nF. 19. Low slope mode is not compliant to the LIN 1.3 or LIN 2.0/2.1 standard. http://onsemi.com 13 NCV7425 REGULATOR TYPICAL PERFORMANCE CHARACTERISTICS (3.3 V Version) Load Transient Responses Figure 8. Load Transient Response (ICC 100 mA to 100 mA) Figure 9. Load Transient Response (ICC 1 mA to 100 mA) Line Transient Responses Figure 10. Line Transient Response (VBB 5 V to 28 V) Figure 11. Line Transient Response (VBB 5 V to 28 V) http://onsemi.com 14 NCV7425 REGULATOR TYPICAL PERFORMANCE CHARACTERISTICS (3.3 V Version) Static Characteristics Figure 12. Dropout Voltage vs. Temperature Figure 13. Output Voltage vs. Output Current Figure 14. Ground Current vs. Output Current Figure 15. Output Voltage vs. Temperature http://onsemi.com 15 NCV7425 REGULATOR TYPICAL PERFORMANCE CHARACTERISTICS (5 V Version) Load Transient Responses Figure 16. Load Transient Response (ICC 100 mA to 100 mA) Figure 17. Load Transient Response (ICC 1 mA to 100 mA) Line Transient Responses Figure 18. Line Transient Response (VBB 6 V to 28 V) Figure 19. Line Transient Response (VBB 6 V to 28 V) http://onsemi.com 16 NCV7425 REGULATOR TYPICAL PERFORMANCE CHARACTERISTICS (5 V Version) Static Characteristics Figure 20. Dropout Voltage vs. Temperature Figure 21. Output Voltage vs. Output Current Figure 22. Ground Current vs. Output Current Figure 23. Output Voltage vs. Temperature http://onsemi.com 17 NCV7425 TxD tBIT tBIT 50% t tBUS_dom(max) LIN tBUS_rec(min) THrec (max) THdom (max) Thresholds of receiving node 1 THrec (min) THdom (min) Thresholds of receiving node 2 t tBUS_dom(min) tBUS_rec(max) PC20060428.2 Figure 24. LIN Transmitter Duty Cycle LIN 100% 60% 60% 40% 40% 0% Tfall t Trise PC20060428.1 Figure 25. LIN Transmitter Rising and Falling Times LIN VBB 60% VBB 40% VBB t RxD trec_prop_down trec_prop_up 50% Figure 26. LIN Receiver Timing http://onsemi.com 18 t PC20060428.3 NCV7425 ORDERING INFORMATION Device NCV7425DW0G NCV7425DW0R2G NCV7425DW5G NCV7425DW5R2G Description Temperature Range Package LIN Transceiver + 3.3 V Regulator + Reset Pin LIN Transceiver + 5 V Regulator + Reset Pin Shipping† 46 Units / Tube −40°C to 125°C SOIC−16, WB, EP (Pb−Free) 1500 / Tape & Reel 46 Units / Tube 1500 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 19 NCV7425 PACKAGE DIMENSIONS SOIC−16 LEAD WIDE BODY, EXPOSED PAD PDW SUFFIX CASE 751AG ISSUE A −U− A M P 0.25 (0.010) M W M 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751R-01 OBSOLETE, NEW STANDARD 751R-02. 9 B 1 R x 45_ 8 −W− G PIN 1 I.D. 14 PL DETAIL E TOP SIDE C F −T− 0.10 (0.004) T K D 16 PL 0.25 (0.010) T U M SEATING PLANE W S J S DETAIL E H EXPOSED PAD 1 SOLDERING FOOTPRINT* 8 0.350 L 16 DIM A B C D F G H J K L M P R 0.050 BACK SIDE CL 0.200 INCHES MIN MAX 0.400 0.411 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.136 0.144 0.010 0.012 0.000 0.004 0.186 0.194 0_ 7_ 0.395 0.415 0.010 0.029 Exposed Pad 0.175 9 MILLIMETERS MIN MAX 10.15 10.45 7.40 7.60 2.35 2.65 0.35 0.49 0.50 0.90 1.27 BSC 3.45 3.66 0.25 0.32 0.00 0.10 4.72 4.93 0_ 7_ 10.05 10.55 0.25 0.75 0.188 CL 0.376 0.074 0.150 0.024 DIMENSIONS: INCHES *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 20 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV7425/D