TI TPS2513DBVR

TPS2513
TPS2514
www.ti.com
SLVSBY8A – MAY 2013 – REVISED MAY 2013
USB Dedicated Charging Port Controller
Check for Samples: TPS2513, TPS2514
FEATURES
DESCRIPTION
•
The TPS2513 and TPS2514 are USB dedicated
charging port (DCP) controllers. An auto-detect
feature monitors USB data line voltage, and
automatically provides the correct electrical
signatures on the data lines to charge compliant
devices among the following dedicated charging
schemes:
1. Divider 1 DCP, required to apply 2 V and 2.7 V
on the D+ and D– Lines respectively
2. Divider 2 DCP, required to apply 2.7 V and 2 V
on the D+ and D– Lines respectively
3. BC1.2 DCP, required to short the D+ Line to the
D– Line
4. Chinese Telecom Standard YD/T 1591-2009
Shorted Mode, required to short the D+ Line to
the D– Line
5. 1.2 V on both D+ and D– Lines
1
•
•
•
•
•
•
•
•
Supports USB DCP Shorting D+ Line to
D– Line per USB Battery Charging
Specification, Revision 1.2 (BC1.2)
Supports Shorted Mode (Shorting D+ Line to
D- Line) per Chinese Telecommunication
Industry Standard YD/T 1591-2009
Supports USB DCP Applying 2.7 V on D+ Line
and 2 V on D- line (or USB DCP Applying
2 V on D+ Line and 2.7 V on D– Line)
Supports USB DCP Applying 1.2 V on
D+ and D– Lines
Automatically Switch D+ and D- Lines
Connections for an Attached Device
Dual USB Port Controller, TPS2513
Single USB Port Controller, TPS2514
Operating Range: 4.5 V to 5.5 V
Available in SOT23-6 Package
APPLICATIONS
•
•
•
Vehicle USB Power Charger
AC-DC Adapter with USB Port
Other USB Charger
VBUS
TPS2561A
TPS2514 DBV
(Top View)
TPS2513 DBV
(Top View)
IN
0.1PF
DP1
GND
DP2
1
2
3
6
5
DM1
DP1
IN
GND
4
DM2 N/C
1
2
3
6
5
DM1
4
N/C
5V
Power
IN
DM1
DD+
GND
DP1
TPS2513
DM2
GND
DP2
VBUS
DD+
GND
GND
USB Connector2
VBUS
USB Connector1
TPS2513, TPS2514 DBV PACKAGE and SIMPLIFIED APPLICATION DIAGRAM
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
TPS2513
TPS2514
SLVSBY8A – MAY 2013 – REVISED MAY 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1)
Over recommended junction temperature range, voltages are referenced to GND (unless otherwise noted)
MIN
Voltage range
MAX
IN
–0.3
7
DP1, DP2 output voltage, DM1, DM2 output voltage
–0.3
5.8
DP1, DP2 input voltage, DM1, DM2 input voltage
–0.3
5.8
UNIT
V
Continuous output sink current
DP1, DP2 input current, DM1, DM2 input current
35
mA
Continuous output source
current
DP1, DP2 output current, DM1, DM2 output current
35
mA
Human Body Model
(HBM)
ESD rating
IN
2
DP1, DP2, DM1, DM2
6
Charging Device Model (CDM)
kV
500
V
Operating Junction Temperature TJ
–40
125
°C
Storage Temperature Range
–65
150
°C
(1)
Tstg
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
THERMAL INFORMATION
TPS2513
TPS2514
THERMAL METRIC (1)
UNITS
DBV (6 PINS)
θJA
Junction-to-ambient thermal resistance
179.9
θJCtop
Junction-to-case (top) thermal resistance
117.5
θJB
Junction-to-board thermal resistance
41.9
ψJT
Junction-to-top characterization parameter
17.2
ψJB
Junction-to-board characterization parameter
41.5
θJCbot
Junction-to-case (bottom) thermal resistance
N/A
(1)
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
spacer
RECOMMENDED OPERATING CONDITIONS
Voltages are referenced to GND (unless otherwise noted), positive current are into pins.
MIN
MAX
4.5
5.5
V
DP1 data line input voltage
0
5.5
V
VDM1
DM1 data line input voltage
0
5.5
V
IDP1
Continuous sink or source current
±10
mA
IDM1
Continuous sink or source current
±10
mA
VDP2
DP2 data line input voltage
0
5.5
V
VDM2
DM2 data line input voltage
0
5.5
V
IDP2
Continuous sink or source current
±10
mA
IDM2
Continuous sink or source current
±10
mA
TJ
Operating junction temperature
125
°C
VIN
Input voltage of IN
VDP1
2
–40
Submit Documentation Feedback
UNIT
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
TPS2513
TPS2514
www.ti.com
SLVSBY8A – MAY 2013 – REVISED MAY 2013
ELECTRICAL CHARACTERISTICS
Conditions are –40°C ≤ (TJ = TA) ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V. Positive current are into pins. Typical values are at 25°C. All
voltages are with respect to GND (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
4.1
4.3
UNIT
UNDERVOLTAGE LOCKOUT
VUVLO
IN rising UVLO threshold voltage
3.9
Hysteresis (1)
100
V
mV
SUPPLY CURRENT
IIN
4.5 V ≤ V IN ≤ 5.5 V
IN supply current
155
200
µA
BC 1.2 DCP MODE (SHORT MODE)
RDPM_SHORT1
DP1 and DM1 shorting resistance
VDP1 = 0.8 V, IDM1 = 1 mA
RDCHG_SHORT1
Resistance between DP1/DM1 and GND
VDP1 = 0.8 V
VDPL_TH_DETACH1
Voltage threshold on DP1 under which the
device goes back to divider mode
157
200
Ω
350
656
1150
kΩ
310
330
350
mV
(1)
VDPL_TH_DETACH_HYS1
Hysteresis
50
RDPM_SHORT2
DP2 and DM2 shorting resistance
VDP2 = 0.8V, IDM2 = 1 mA
RDCHG_SHORT2
Resistance between DP2/DM2 and GND
VDP2 = 0.8 V
VDPL_TH_DETACH2
Voltage threshold on DP2 under which the
device goes back to divider mode
VDPL_TH_DETACH_HYS2
Hysteresis (1)
mV
157
200
Ω
350
656
1150
kΩ
310
330
350
mV
50
mV
DIVIDER MODE
VDP1_2.7V
DP1 output voltage
VIN = 5 V
2.57
2.7
2.84
V
VDM1_2V
DM1 output voltage
VIN = 5 V
RDP1_PAD1
DP1 output impedance
IDP1 = –5 µA
1.9
2
2.1
V
24
30
36
kΩ
RDM1_PAD1
DM1 output impedance
IDM1 = –5 µA
24
VDP2_2.7V
DP2 output voltage
VIN = 5 V
2.57
30
36
kΩ
2.7
2.84
V
VDM2_2V
DM2 output voltage
VIN = 5 V
1.9
2
2.1
V
RDP2_PAD1
DP2 output impedance
IDP2 = –5 µA
24
30
36
kΩ
RDM2_PAD1
DM2 output impedance
IDM2 = –5 µA
24
30
36
kΩ
VDP1_1.2V
DP1 output voltage
VIN = 5 V
1.12
1.2
1.28
V
VDM1_1.2V
DM1 output voltage
VIN = 5 V
1.12
1.2
1.28
V
RDM1_PAD2
DP1 output impedance
IDP1 = –5 µA
80
102
130
kΩ
RDP1_PAD2
DM1 output impedance
IDM1 = –5 µA
80
102
130
kΩ
VDP2_1.2V
DP2 output voltage
VIN = 5 V
1.12
1.2
1.28
V
VDM2_1.2V
DM2 output voltage
VIN = 5 V
1.12
1.2
1.28
V
RDP2_PAD2
DP2 output impedance
IDP2 = –5 µA
80
102
130
kΩ
RDM2_PAD2
DM2 output impedance
IDM2 = –5 µA
80
102
130
kΩ
1.2 V / 1.2 V MODE
(1)
Specified by design. Not production tested.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
3
TPS2513
TPS2514
SLVSBY8A – MAY 2013 – REVISED MAY 2013
www.ti.com
FUNCTIONAL BLOCK DIAGRAM, TPS2513
S1
DM1
S2
IN
Auto-detect
S4
DP1
S3
2.7V
2.0V
1.2V
UVLO
S5
DM2
DRIVER
S6
Auto-detect
S8
GND
DP2
S7
2.7V
2.0V
1.2V
SPACER
FUNCTIONAL BLOCK DIAGRAM, TPS2514
S1
IN
DM1
S2
UVLO
S4
S3
DRIVER
2.7V
2.0V
Auto-detect
DP1
1.2V
N/C
N/C
GND
4
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
TPS2513
TPS2514
www.ti.com
SLVSBY8A – MAY 2013 – REVISED MAY 2013
DEVICE INFORMATION
TPS2513 DBV (SOT23-6)
(TOP VIEW)
DP1
GND
DP2
1
2
3
6
5
DM1
4
DM2
IN
Table 1. PIN FUNCTIONS, TPS2513
NO.
NAME
TYPE (1)
DESCRIPTION
1
DP1
I/O
Connected to the D+ or D– line of USB connector, provide the correct voltage with attached portable
equipment for DCP detection.
2
GND
G
Ground connection
3
DP2
I/O
Connected to the D+ or D– line of USB connector, provide the correct voltage with attached portable
equipment for DCP detection.
4
DM2
I/O
Connected to the D+ or D– line of USB connector, provide the correct voltage with attached portable
equipment for DCP detection.
5
IN
6
DM1
(1)
P
Power supply. Connect a ceramic capacitor with a value of 0.1-μF or greater from the IN pin to GND as close
to the device as possible.
I/O
Connected to the D+ or D– line of USB connector, provide the correct voltage with attached portable
equipment for DCP detection.
G = Ground, I = Input, O = Output, P = Power
TPS2514 DBV (SOT23-6)
(TOP VIEW)
DP1
GND
N/C
1
2
3
6
5
DM1
4
N/C
IN
Table 2. PIN FUNCTIONS, TPS2514
NO.
(1)
NAME
TYPE
(1)
DESCRIPTION
1
DP1
I/O
Connected to the D+ or D– line of USB connector, provide the correct voltage with attached portable
equipment for DCP detection.
2
GND
G
Ground connection
3
N/C
–
No connect pin. Can be grounded or left floating.
4
N/C
–
No connect pin. Can be grounded or left floating.
5
IN
P
Power supply. Connect a ceramic capacitor with a value of 0.1-μF or greater from the IN pin to GND as close
to the device as possible.
6
DM1
I/O
Connected to the D+ or D– line of USB connector, provide the correct voltage with attached portable
equipment for DCP detection.
G = Ground, I = Input, O = Output, P = Power
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
5
TPS2513
TPS2514
SLVSBY8A – MAY 2013 – REVISED MAY 2013
www.ti.com
TYPICAL CHARACTERISTICS
POWER ON (DM1 and DP1)
6
POWER OFF (DM1 and DP1)
6
V
VIN
IN
DM1
5
V
DVIN
IN
DM1
DP1
5
VIN, DM1, DP1 (V)
VIN, DM1, DP1 (V)
DP1
4
3
2
1
0
4
3
2
1
0
±1
±0.008
±0.006
±0.004
±0.002
0.000
0.002
Time (s)
±1
-0.04
0.004
-0.02
0
0.02
Figure 1.
VIN, DM2, DP2 (V)
VIN, DM2, DP2 (V)
V
DVIN
IN
DM2
DM1
DP2
DP1
5
4
3
2
1
4
3
2
1
0
±1
±0.008
±0.006
±0.004
±0.002
0.000
0.002
Time (s)
±1
-0.04
0.004
-0.02
0
0.02
0.04
0.06
0.08
Time (s)
C003
0.1
C004
Figure 3.
Figure 4.
DP1 and DM1 OUTPUT VOLTAGE
vs
TEMPERATURE
DP2 and DM2 OUTPUT VOLTAGE
vs
TEMPERATURE
3.2
3.2
VIN = 5 V
DP2 and DM2 Output Voltage (V)
DP1 and DM1 Output Voltage (V)
0.1
POWER OFF (DM2 and DP2)
0
2.8
2.4
2
DP1
V
DP1
V
DM1
DM1
1.6
±40
±20
0
20
40
60
80
100
TJ Junction Temperature (ƒC)
120
VIN = 5 V
2.8
2.4
2
DP1
V
DP2
V
DM1
DM2
1.6
140
±40
±20
C005
Figure 5.
6
0.08
C002
6
VIN
VIN
DM2
DP2
5
0.06
Figure 2.
POWER ON (DM2 and DP2)
6
0.04
Time (s)
C001
0
20
40
60
80
TJ Junction Temperature (ƒC)
100
120
140
C006
Figure 6.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
TPS2513
TPS2514
www.ti.com
SLVSBY8A – MAY 2013 – REVISED MAY 2013
TYPICAL CHARACTERISTICS (continued)
SUPPLY CURRENT
vs
TEMPERATURE
180
VIN = 5 V
Supply Current (µA)
170
160
150
140
130
±40
±20
0
20
40
60
80
100
TJ Junction Temperature (ƒC)
120
140
C007
Figure 7.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
7
TPS2513
TPS2514
SLVSBY8A – MAY 2013 – REVISED MAY 2013
www.ti.com
DETAILED DESCRIPTION
OVERVIEW
The following overview references various industry standards. It is always recommended to consult the latest
standard to ensure the most recent and accurate information.
Rechargeable portable equipment requires an external power source to charge its batteries. USB ports are
convenient locations for charging because of an available 5-V power source. Universally accepted standards are
required to ensure host and client-side devices meet the power management requirements. Traditionally, USB
host ports following the USB 2.0 Specification must provide at least 500 mA to downstream client-side devices.
Because multiple USB devices can be attached to a single USB port through a bus-powered hub, it is the
responsibility of the client-side device to negotiate the power allotment from the host to guarantee the total
current draw does not exceed 500 mA. In general, each USB device can subsequently request more current,
which is granted in steps of 100 mA up 500 mA total. The host may grant or deny the request based on the
available current.
Additionally, the success of the USB technology makes the micro-USB connector a popular choice for wall
adapter cables. This allows a portable device to charge from both a wall adapter and USB port with only one
connector.
One common difficulty has resulted from this. As USB charging has gained popularity, the 500-mA minimum
defined by the USB 2.0 Specification or 900 mA defined in the USB 3.0 Specification, has become insufficient for
many handsets, tablets and personal media players (PMP) which have a higher rated charging current. Wall
adapters and car chargers can provide much more current than 500 mA or 900 mA to fast charge portable
devices. Several new standards have been introduced defining protocol handshaking methods that allow host
and client devices to acknowledge and draw additional current beyond the 500 mA (defined in the USB 2.0
Specification) or 900 mA (defined in the USB 3.0 Specification) minimum while using a single micro-USB input
connector.
The TPS2513 and TPS2514 support four of the most common protocols:
• USB Battery Charging Specification, Revision 1.2 (BC1.2)
• Chinese Telecommunications Industry Standard YD/T 1591-2009
• Divider mode
• 1.2 V on both D+ and D– lines
YD/T 1591-2009 is a subset of the BC1.2 specification supported by the vast majority of devices that implement
USB charging. Divider and 1.2-V charging schemes are supported in devices from specific yet popular device
makers. BC1.2 has three different port types, listed as follows.
• Standard downstream port (SDP)
• Charging downstream port (CDP)
• Dedicated charging port (DCP)
The BC1.2 Specification defines a charging port as a downstream facing USB port that provides power for
charging portable equipment.
Table 3 shows different port operating modes according to the BC1.2 Specification.
Table 3. Operating Modes Table
8
PORT TYPE
SUPPORTS USB2.0
COMMUNICATION
MAXIMUM ALLOWABLE CURRENT
DRAWN BY PORTABLE EQUIPMENT (A)
SDP (USB 2.0)
Yes
0.5
SDP (USB 3.0)
Yes
0.9
CDP
Yes
1.5
DCP
No
1.5
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
TPS2513
TPS2514
www.ti.com
SLVSBY8A – MAY 2013 – REVISED MAY 2013
The BC1.2 Specification defines the protocol necessary to allow portable equipment to determine what type of
port it is connected to so that it can allot its maximum allowable current drawn. The hand-shaking process is two
steps. During step one, the primary detection, the portable equipment outputs a nominal 0.6 V output on its D+
line and reads the voltage input on its D– line. The portable device concludes it is connected to a SDP if the
voltage is less than the nominal data detect voltage of 0.3 V. The portable device concludes that it is connected
to a Charging Port if the D– voltage is greater than the nominal data detect voltage of 0.3V and less than 0.8 V.
The second step, the secondary detection, is necessary for portable equipment to determine between a CDP and
a DCP. The portable device outputs a nominal 0.6 V output on its D– line and reads the voltage input on its D+
line. The portable device concludes it is connected to a CDP if the data line being remains is less than the
nominal data detect voltage of 0.3 V. The portable device concludes it is connected to a DCP if the data line
being read is greater than the nominal data detect voltage of 0.3 V and less than 0.8 V.
Dedicated Charging Port (DCP)
A dedicated charging port (DCP) is a downstream port on a device that outputs power through a USB connector,
but is not capable of enumerating a downstream device, which generally allows portable devices to fast charge at
their maximum rated current. A USB charger is a device with a DCP, such as a wall adapter or car power
adapter. A DCP is identified by the electrical characteristics of its data lines. The following DCP identification
circuits are usually used to meet the handshaking detections of different portable devices.
Short the D+ Line to the D– Line
The USB BC1.2 Specification and the Chinese Telecommunications Industry Standard YD/T 1591-2009 define
that the D+ and D– data lines should be shorted together with a maximum series impedance of 200 Ω. This is
shown in Figure 8.
D200 Ÿ (max)
D+
GND
USB Connector
VBUS
5.0 V
Figure 8. DCP Short Mode
Divider 1 (DCP Applying 2 V on D+ Line and 2.7 V on D– Line) or Divider 2 (DCP Applying 2.7 V on D+
Line and 2 V on D– Line)
There are two charging schemes for divider DCP. They are named after Divider 1 and Divider 2 DCPs that are
shown in Figure 9 and Figure 10. The Divider 1 charging scheme is used for 5-W adapters, and applies 2 V to
the D+ line and 2.7 V to the D– data line. The Divider 2 charging scheme is used for 10-W adapters, and applies
2.7 V on the D+ line and 2 V is applied on the D– line.
DD+
2.7 V 2.0 V
GND
VBUS
5.0 V
DD+
2.0 V 2.7 V
GND
Figure 9. Divider 1 DCP
USB Connector
VBUS
USB Connector
5.0 V
Figure 10. Divider 2 DCP
Applying 1.2 V to the D+ Line and 1.2 V to the D– Line
As shown in Figure 11, some tablet USB chargers require 1.2 V on the shorted data lines of the USB connector.
The maximum resistance between the D+ line and the D- line is 200 Ω.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
9
TPS2513
TPS2514
SLVSBY8A – MAY 2013 – REVISED MAY 2013
www.ti.com
D200 Ÿ (max)
D+
1.2 V
GND
USB Connector
VBUS
5.0 V
Figure 11. DCP Applying 1.2 V to the D+ Line and 1.2 V to the D– Line
The TPS2513 and TPS2514 are USB dedicated charging port (DCP) controllers. Applications include vehicle
power charger, wall adapters with USB DCP and other USB chargers. The TPS2513 and TPS2514 DCP
controllers have the auto-detect feature that monitors the D+ and D– line voltages of the USB connector,
providing the correct electrical signatures on the DP and DM pins for the correct detections of compliant portable
devices to fast charge. These portable devices include smart phones, 5-V tablets and personal media players.
DCP Auto-Detect
The TPS2513 and TPS2514 integrate an auto-detect feature to support divider mode, short mode and 1.2 V / 1.2
V modes. If a divider device is attached, 2.7 V is applied to the DP pin and 2 V is applied to the DM pin. If a
BC1.2-compliant device is attached, the TPS2513 and TPS2514 automatically switches into short mode. If a
device compliant with the 1.2 V / 1.2 V charging scheme is attached, 1.2 V is applied on both the DP pin and the
DM pin. The functional diagram of DCP auto-detect feature (DM1 and DP1) is shown in Figure 12. DCP autodetect feature (DM2 and DP2 of TPS2513) has the same functional configuration.
5V
S1
S2
DM1
D-
DP1
D+
S4
GND
S3
2.0V
2.7V
1.2 V
GND
USB Connector
VBUS
Divider 2
S1, S2: ON
S3, S4: OFF
Short Mode
S4 ON
S1, S2, S3: OFF
1.2V on DP1 and DM1
S3, S4: ON
S1, S2: OFF
TPS2513, TPS2514
Figure 12. TPS2513 and TPS2514 DCP Auto-Detect Functional Diagram
Undervoltage Lockout (UVLO)
The undervoltage lockout (UVLO) circuit disables DP1, DM1, DP2 and DM2 output voltage until the input voltage
reaches the UVLO turn-on threshold. Built-in hysteresis prevents unwanted oscillations due to input voltage drop
from large current surges.
10
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
TPS2513
TPS2514
www.ti.com
SLVSBY8A – MAY 2013 – REVISED MAY 2013
APPLICATION INFORMATION
The TPS2513 and TPS2514 only provide the correct electrical signatures on the data line of USB charger port
and do not provide any power for the VBUS.
Divide Mode Selection of 5-W and 10-W USB Chargers
The TPS2513 and TPS2514 provide two types of connections between the DP pin and the DM pin and between
the D+ data line and the D– data line of the USB connector for a 5-W USB charger and a 10-W USB charger
with a single USB port. For 5-W USB charger, the DP1 pin is connected to the D– line and the DM1 pin is
connected to the D+ line. This is shown in Figure 13. For 10-W USB charger, the DP1 pin is connected to the D+
line and the DM1 pin is connected to the D– line. This is shown in Figure 14. Table 4 shows different charging
schemes for both 5-W and 10-W USB charger solutions. DP2 and DM2 of TPS2513 also provides this two types
of connections.
Table 4. Charging Schemes for 5-W and 10-W USB Chargers
USB CHARGER TYPE
CONTAINING CHARGING SCHEMES
5-W
Divider 1
1.2 V on both D+ and D– Lines
BC1.2 DCP
10 -W
Divider 2
1.2 V on both D+ and D– Lines
BC1.2 DCP
5.0 V
5.0 V
TPS2513, TPS2514
DP1
D+
GND
VBUS
DM1
TPS2513, TPS2514
DP1
DD+
GND
Figure 13. 5-W USB Charger Application
USB Connector
DM1
D-
USB Connector
VBUS
Figure 14. 10-W USB Charger Application
Layout Guidelines
Place the TPS2513 and TPS2514 near the USB output connector and place the 0.1-μF bypass capacitor near
the IN pin.
spacer
REVISION HISTORY
Changes from Original (May 2013) to Revision A
•
Page
Changed the device From: Product Preview To: Production ................................................................................................ 1
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: TPS2513 TPS2514
11
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
TPS2513DBVR
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
2513
TPS2513DBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
2513
TPS2514DBVR
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
2514
TPS2514DBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
2514
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2013
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jun-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
TPS2513DBVR
SOT-23
DBV
6
3000
178.0
9.0
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.23
3.17
1.37
4.0
8.0
Q3
TPS2513DBVT
SOT-23
DBV
6
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS2514DBVR
SOT-23
DBV
6
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
TPS2514DBVT
SOT-23
DBV
6
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jun-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS2513DBVR
SOT-23
DBV
6
3000
180.0
180.0
18.0
TPS2513DBVT
SOT-23
DBV
6
250
180.0
180.0
18.0
TPS2514DBVR
SOT-23
DBV
6
3000
180.0
180.0
18.0
TPS2514DBVT
SOT-23
DBV
6
250
180.0
180.0
18.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated