TI TUSB1210BRHBT

TUSB1210
Standalone USB Transceiver Chip Silicon
Data Manual
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Literature Number: SLLSE09F
November 2009 – Revised August 2012
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Contents
1
2
Features ............................................................................................................................. 6
Description ......................................................................................................................... 7
2.1
2.2
3
4
5
6
7
8
9
2
Terminal Description ........................................................................................................ 7
TUSB1210 Block Diagram ................................................................................................. 9
....................................................................................................
3.1
Absolute Maximum Ratings ..............................................................................................
3.2
Recommended Operating Conditions ..................................................................................
3.3
ESD Electrical Parameters ...............................................................................................
Clock System ....................................................................................................................
4.1
USB PLL Reference Clock ...............................................................................................
4.2
ULPI Input Clock Configuration ..........................................................................................
4.3
ULPI Output Clock Configuration ........................................................................................
4.4
Clock 32 kHz ...............................................................................................................
4.5
Reset ........................................................................................................................
Power Module ...................................................................................................................
5.1
Power Providers ...........................................................................................................
5.1.1
VDD33 Regulator .................................................................................................
5.1.2
VDD18 Supply .....................................................................................................
5.1.3
VDD15 Regulator .................................................................................................
5.2
Power Consumption .......................................................................................................
5.3
Power Management .......................................................................................................
5.3.1
Power On Sequence ...........................................................................................
5.3.1.1
Timing Diagram ....................................................................................
5.3.2
Timers and Debounce .........................................................................................
USB Connectivity ..............................................................................................................
6.1
Timing Parameter Definitions ............................................................................................
6.2
Interface Target Frequencies ............................................................................................
6.3
USB Transceiver ...........................................................................................................
6.3.1
TUSB1210 Modes vs ULPI Pin Status ......................................................................
6.3.2
ULPI Interface Timing ..........................................................................................
6.3.3
PHY Electrical Characteristics ................................................................................
6.3.3.1
LS/FS Single-Ended Receivers ..................................................................
6.3.3.2
LS/FS Differential Receiver .......................................................................
6.3.3.3
LS/FS Transmitter ..................................................................................
6.3.3.4
HS Differential Receiver ...........................................................................
6.3.3.5
HS Differential Transmitter ........................................................................
6.3.3.6
UART Transceiver .................................................................................
6.3.4
OTG Electrical Characteristics ................................................................................
I/O Electrical Characteristics ...............................................................................................
7.1
Analog I/O Electrical Characteristics ....................................................................................
7.2
Digital I/O Electrical Characteristics .....................................................................................
7.3
Electrical Characteristics: Digital IO Pins (Non-ULPI) ................................................................
External Components ........................................................................................................
Register Map .....................................................................................................................
9.1
TUSB1210 Product ........................................................................................................
9.1.1
VENDOR_ID_LO ...............................................................................................
9.1.2
VENDOR_ID_HI ................................................................................................
9.1.3
PRODUCT_ID_LO .............................................................................................
9.1.4
PRODUCT_ID_HI ..............................................................................................
9.1.5
FUNC_CTRL ....................................................................................................
9.1.6
FUNC_CTRL_SET .............................................................................................
Electrical Characteristics
Contents
10
10
10
10
11
11
11
11
12
12
13
13
13
13
13
14
15
15
15
16
17
17
17
17
18
19
19
20
20
20
22
22
23
24
26
26
26
26
27
28
28
29
29
29
30
30
31
Copyright © 2009–2012, Texas Instruments Incorporated
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9.1.7
9.1.8
9.1.9
9.1.10
9.1.11
9.1.12
9.1.13
9.1.14
9.1.15
9.1.16
9.1.17
9.1.18
9.1.19
9.1.20
9.1.21
9.1.22
9.1.23
9.1.24
9.1.25
9.1.26
9.1.27
9.1.28
9.1.29
9.1.30
9.1.31
9.1.32
9.1.33
9.1.34
9.1.35
9.1.36
10
Application Information
10.1
10.2
11
12
FUNC_CTRL_CLR .............................................................................................
IFC_CTRL .......................................................................................................
IFC_CTRL_SET ................................................................................................
IFC_CTRL_CLR ................................................................................................
OTG_CTRL ......................................................................................................
OTG_CTRL_SET ...............................................................................................
OTG_CTRL_CLR ...............................................................................................
USB_INT_EN_RISE ............................................................................................
USB_INT_EN_RISE_SET .....................................................................................
USB_INT_EN_RISE_CLR .....................................................................................
USB_INT_EN_FALL ...........................................................................................
USB_INT_EN_FALL_SET .....................................................................................
USB_INT_EN_FALL_CLR .....................................................................................
USB_INT_STS ..................................................................................................
USB_INT_LATCH ..............................................................................................
DEBUG ..........................................................................................................
SCRATCH_REG ................................................................................................
SCRATCH_REG_SET .........................................................................................
SCRATCH_REG_CLR .........................................................................................
VENDOR_SPECIFIC1 .........................................................................................
VENDOR_SPECIFIC1_SET ..................................................................................
VENDOR_SPECIFIC1_CLR ..................................................................................
VENDOR_SPECIFIC2 .........................................................................................
VENDOR_SPECIFIC2_SET ..................................................................................
VENDOR_SPECIFIC2_CLR ..................................................................................
VENDOR_SPECIFIC1_STS ..................................................................................
VENDOR_SPECIFIC1_LATCH ...............................................................................
VENDOR_SPECIFIC3 .........................................................................................
VENDOR_SPECIFIC3_SET ..................................................................................
VENDOR_SPECIFIC3_CLR ..................................................................................
31
32
33
34
34
36
36
37
38
38
39
40
40
41
42
43
43
44
44
45
45
46
47
48
48
49
49
50
51
51
...................................................................................................... 53
Host or OTG, ULPI Input Clock Mode Application .................................................................... 53
Device, ULPI Output Clock Mode Application ......................................................................... 53
Glossary ........................................................................................................................... 55
TUSB1210 Package ............................................................................................................ 57
12.1
12.2
TUSB1210 Standard Package Symbolization
Package Thermal Resistance Characteristics
Copyright © 2009–2012, Texas Instruments Incorporated
.........................................................................
.........................................................................
Contents
57
57
3
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
List of Figures
....................................................................
5-1
TUSB1210 Power-Up Timing (ULPI Clock Input Mode)
6-1
USB UART Data Flow ........................................................................................................... 23
10-1
Host or OTG, ULPI Input Clock Mode Application Diagram ................................................................ 53
10-2
Device, ULPI Output Clock Mode Application Diagram ..................................................................... 54
12-1
Printed Device Reference ....................................................................................................... 57
4
List of Figures
15
Copyright © 2009–2012, Texas Instruments Incorporated
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
List of Tables
2-1
Terminal Functions ................................................................................................................ 8
4-1
Electrical Characteristics: Clock Input
6-2
........................................................................................
Electrical Characteristics: REFCLK ...........................................................................................
Performances .....................................................................................................................
Summary of TUSB1210 Power Providers.....................................................................................
VDD33 Internal LDO Regulator Characteristics ................................................................................
VDD15 Internal LDO Regulator Characteristics ................................................................................
Power Consumption .............................................................................................................
Timing Parameter Definitions ...................................................................................................
TUSB1210 Interface Target Frequencies .....................................................................................
6-3
TUSB1210 Modes vs ULPI Pin Status:ULPI Synchronous Mode Power-Up
6-4
TUSB1210 Modes vs ULPI Pin Status: USB Suspend Mode
4-2
4-3
5-1
5-2
5-3
5-4
6-1
6-5
6-6
6-7
6-8
6-9
6-10
6-11
6-12
6-13
6-14
6-15
6-16
6-17
7-1
8-1
8-2
9-1
12-1
12-2
......................................................................................................................................
.............................................................
TUSB1210 Modes vs ULPI Pin Status: ULPI 6-Pin Serial Mode and UART Mode .....................................
ULPI Interface Timing............................................................................................................
LS/FS Single-Ended Receivers ................................................................................................
LS/FS Differential Receiver .....................................................................................................
LS Transmitter ....................................................................................................................
FS Transmitter ....................................................................................................................
HS Differential Receiver .........................................................................................................
HS Transmitter ....................................................................................................................
USB UART Interface Timing Parameters .....................................................................................
CEA-2011/UART Transceiver ..................................................................................................
Pullup/Pulldown Resistors.......................................................................................................
OTG VBUS Electrical ..............................................................................................................
OTG ID Electrical .................................................................................................................
Electrical Characteristics: Analog Output Pins ..............................................................................
TUSB1210 External Components ..............................................................................................
TUSB1210 VBUS Capacitors.....................................................................................................
USB Register Summary .........................................................................................................
TUSB1210 Nomenclature Description .........................................................................................
TUSB1210 Thermal Resistance Characteristics .............................................................................
Copyright © 2009–2012, Texas Instruments Incorporated
List of Tables
11
11
12
13
13
14
14
17
17
18
18
19
19
20
20
20
22
22
23
23
23
24
24
25
26
27
27
28
57
57
5
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
Standalone USB Transceiver Chip Silicon
Check for Samples: TUSB1210
1
Features
• USB2.0 PHY Transceiver Chip, Designed to
Interface With a USB Controller via a ULPI
Interface, Fully Compliant With:
– Universal Serial Bus Specification Rev. 2.0
– On-The-Go Supplement to the USB 2.0
Specification Rev. 1.3
– UTMI+ Low Pin Interface (ULPI) Specification
Rev. 1.1
– ULPI 12-pin SDR Interface
• DP/DM Line External Component
Compensation (TI Patent Pending)
• Interfaces to Host, Peripheral and OTG Device
Cores; Optimized for Portable Devices or
System ASICs with Built-in USB OTG Device
Core
• Complete USB OTG Physical Front-End that
Supports Host Negotiation Protocol (HNP) and
Session Request Protocol (SRP)
• VBUS Overvoltage Protection Circuitry Protects
VBUS Pin in Range –2 V to 20 V
• Internal 5 V Short-Circuit Protection of DP, DM,
and ID Pins for Cable Shorting to VBUS Pin
• ULPI Interface:
– I/O Interface (1.8V) Optimized for NonTerminated 50 Ω Line Impedance
– ULPI CLOCK Pin (60 MHz) Supports Both
Input and Output Clock Configurations
– Fully Programmable ULPI-Compliant
Register Set
• Full Industrial Grade Operating Temperature
Range from –40°C to 85°C
• Available in a 32-Pin Quad Flat No Lead [QFN
(RHB)] Package
• Can Be Interfaced to Peripheral, Host or OTG
Controller Devices via ULPI. Suited to Portable
Devices or System ASICs with Built-In
6
Features
Controller Core.
• Complete HS-USB Physical Front-End:
– Supports High Speed (480 Mbit/s), Full
Speed (12 Mbit/s) and Low Speed (1.5 Mbit/s)
– Integrated Phase-Locked Loop (PLL)
Supporting 2 Clock Frequencies 19.2 MHz/26
MHz
– Integrated 45 Ω ±10% High-Speed
Termination Resistors, 1.5 kΩ Full-Speed
Device Pull-up Resistor, 15 kΩ Host
Termination Resistors
– Integrated Transmit and Receive Paths for
Parallel-to-Serial and Serial-to-Parallel Data
Conversion
– USB Data Recovery to Allow Recovery of
USB Data up to ±500 ppm Frequency Drift
– Bit-Stuffing Insertion During Transmit and
Removal During Receive
– Non-Return-to-Zero Inverted (NRZI)
Encoding and Decoding
– Supports Bus Reset, Suspend, Resume and
High-Speed Detection Handshake (Chirp)
– HS USB DP/DM Impedance Programmability
for External Component Compensation
• OTG Ver1.3 :
– Control of External VBUS Switch or Charge
Pump
– Both Session Request Protocol (SRP)
Methods Supported: Data Pulsing and VBUS
Pulsing
– Integrated VBUS Detectors and Cable
Detection (ID)
• Internal Power-On Reset (POR) Circuit
• Flexible System Integration and Very Low
Current Consumption, Optimized for Portable
Devices
Copyright © 2009–2012, Texas Instruments Incorporated
TUSB1210
www.ti.com
2
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Description
The TUSB1210 is a USB2.0 transceiver chip, designed to interface with a USB controller via a ULPI
interface. It supports all USB2.0 data rates (High-Speed 480Mbps, Full-Speed 12 Mbps and Low-Speed
1.5Mbps), and is compliant to both Host and Peripheral modes. It additionally supports a UART mode and
legacy ULPI serial modes.
TUSB1210 also supports the OTG (Ver1.3) optional addendum to the USB 2.0 Specification, including
Host Negotiation Protocol (HNP) and Session Request Protocol (SRP).
TUSB1210 is optimized to be interfaced through a 12-pin SDR UTMI Low Pin Interface (ULPI), supporting
both input clock and output clock modes, with 1.8 V interface supply voltage.
TUSB1210 integrates a 3.3 V LDO, which makes it flexible to work with either battery operated systems or
pure 3.3 V supplied systems. Both the main supply and the 3.3 V power domain can be supplied through
an external switched-mode converter for optimized power efficiency.
TUSB1210 includes a POR circuit to detect supply presence on VBAT and VDDIO pins. TUSB1210 can be
disabled or configured in low power mode for energy saving.
TUSB1210 is protected against accidental shorts to 5 V or ground on its exposed interface (DP/DM/ID). It
is also protected against up to 20 V surges on VBUS.
TUSB1210 integrates a high-performance low-jitter 480 MHz PLL and supports two clock configurations.
Depending on the required link configuration, TUSB1210 supports both ULPI input and output clock
mode : input clock mode, in which case a square-wave 60 MHz clock is provided to TUSB1210 at the
ULPI interface CLOCK pin; and output clock mode in which case TUSB1210 can accept a square-wave
reference clock at REFCLK of either 19.2 MHz, 26 MHz. Frequency is indicated to TUSB1210 via the
configuration pin CFG. This can be useful if a reference clock is already available in the system.
2.1
1
Terminal Description
REFCLK
VDDIO
DIR
VDD18
STP
VDD18
RESETB
CLOCK
N/C
32
31
30
29
28
27
26
25
RHB PACKAGE
(TOP VIEW)
24 N/C
1
NXT
2
DATA0
3
TUSB1210
23 ID
22 VBUS
DATA1
4
32-pin QFN
21 VBAT
DATA2
5
20 VDD33
DATA3
6
19 DM
DATA4
7
N/C
8
18 DP
GND
9
10
11
12
13
14
15
16
DATA5
DATA6
CS
VDD15
DATA7
CFG
N/C
N/C
17 CPEN
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to
specifications per the terms of the Texas Instruments standard warranty. Production
processing does not necessarily include testing of all parameters.
Copyright © 2009–2012, Texas Instruments Incorporated
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
Table 2-1. Terminal Functions
TERMINAL
NO.
1
NAME
A/D
TYPE
LEVEL
DESCRIPTION
I
3.3 V
VDD33 Reference clock input (square-wave only). Tie to GND when pin 26
(CLOCK) is required to be Input mode. Connect to square-wave reference
clock of amplitude in the range of 3 V to 3.6 V when Pin 26 (CLOCK) is
required to be Output mode. See pin 14 (CFG) description for REFCLK
input frequency settings.
REFCLK
A
2
NXT
D
O
VDDIO
ULPI NXT output signal
3
DATA0
D
I/O
VDDIO
ULPI DATA input/output signal 0 synchronized to CLOCK
4
DATA1
D
I/O
VDDIO
ULPI DATA input/output signal 1 synchronized to CLOCK
5
DATA2
D
I/O
VDDIO
ULPI DATA input/output signal 2 synchronized to CLOCK
6
DATA3
D
I/O
VDDIO
ULPI DATA input/output signal 3 synchronized to CLOCK
7
DATA4
D
I/O
VDDIO
ULPI DATA input/output signal 4 synchronized to CLOCK
8
N/C
–
–
VDDIO
No connect
9
DATA5
D
I/O
VDDIO
ULPI DATA input/output signal 5 synchronized to CLOCK
10
DATA6
D
I/O
VDDIO
ULPI DATA input/output signal 6 synchronized to CLOCK
11
CS
D
I
VDDIO
Active-high chip select pin. When low the IC is in power down and ULPI
bus is tri-stated. When high normal operation. Tie to VDDIO if unused.
12
VDD15
A
power
13
DATA7
D
I/O
VDDIO
ULPI DATA input/output signal 7 synchronized to CLOCK
14
CFG
D
I
VDDIO
REFCLK clock frequency configuration pin. Two frequencies are
supported: 19.2 MHz when 0, or 26 MHz when 1.
15
N/C
–
–
–
No connect
16
N/C
–
–
–
No connect
17
CPEN
D
O
VDD33
CMOS active-high digital output control of external 5V VBUS supply
18
DP
A
I/O
VDD33
DP pin of the USB connector
19
DM
A
I/O
VDD33
DM pin of the USB connector
20
VDD33
A
power
VDD33
3.3-V internal LDO output. Connect to external filtering capacitor.
21
VBAT
A
power
VBAT
Input supply voltage or battery source
22
VBUS
A
power
VBUS
VBUS pin of the USB connector
23
ID
A
I/O
VDD33
Identification (ID) pin of the USB connector
24
N/C
–
–
–
No connect
25
N/C
–
–
–
No connect
1.5-V internal LDO output. Connect to external filtering capacitor.
ULPI 60 MHz clock on which ULPI data is synchronized.
Two modes are possible:
26
CLOCK
D
O
VDDIO
Input Mode: CLOCK defaults as an input.
Output Mode: When an input clock is detected on REFCLK pin (after 4
rising edges) then CLOCK will change to an output.
8
27
RESETB
D
I
VDDIO
When low, all digital logic (except 32 kHz logic required for power up
sequencing) including registers are reset to their default values, and ULPI
bus is tri-stated. When high, normal USB operation.
28
VDD18
A
power
VDD18
External 1.8-V supply input. Connect to external filtering capacitor.
29
STP
D
I
VDDIO
ULPI STP input signal
30
VDD18
A
power
VDD18
External 1.8-V supply input. Connect to external filtering capacitor.
31
DIR
D
O
VDDIO
ULPI DIR output signal
32
VDDIO
A
I
VDDIO
External 1.8V supply input for digital I/Os. Connect to external filtering
capacitor.
Description
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
2.2
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
TUSB1210 Block Diagram
VDDIO (32)
POR
VIO
POR
VBAT
CTRL
VBAT (21)
BGAP
& REF
1V5
POR
DIG
( 1) REFCLK
(11) CS
(14) CFG
(27) RESETB
32K
RST_DIG
VDD15 (12)
DIG
USB-IP
VDD18 (30)
VDD18 (28)
VDD33 (20)
DP (18)
DM (19)
ID (23)
VBUS (22)
1V8
PLL
3V3
OTG
PHY
ANA
PHY
DIG
+
ULPI
+
REGS
PWR_ FSM
( 8) N/C
(15 ) N/C
(16 ) N/C
(25 ) N/C
(24) N /C
OTG
TEST
(17) CPEN
PKG Substrate
(Ground )
(3:7,9:10,13)
DATA(7:0)
(2 ) NXT
(31) DIR
(29) STP
(26) CLOCK
Description
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
9
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
3
Electrical Characteristics
3.1
Absolute Maximum Ratings
www.ti.com
over operating free-air temperature range (unless otherwise noted) (1)
PARAMETER
VCC
Main battery supply voltage
CONDITIONS
MIN
MAX
(2)
UNIT
0
5
V
Where supply represents the voltage applied
to the power supply pin associated with the
input
–0.3
1 × VCC +0.3
V
–2
20
V
ID, DP, DM inputs
Stress condition guaranteed 24h
–0.3
5.25
V
VDDIO
IO supply voltage
Continuous
1.98
V
Tstg
Storage temperature range
–55
125
°C
TA
Ambient temperature range
–40
85
°C
Absolute maximum rating
–40
150
For parametric compliance
–40
125
–40
85
°C
5.25
V
Voltage on any input (3)
VBUS input
TJ
Ambient temperature range
Ambient temperature for parametric
compliance
(1)
(2)
(3)
With max 125°C as junction temperature
DP, DM, ID high voltage short circuit
DP, DM or ID pins short circuited to VBUS
supply, in any mode of TUSB1210 operation,
continuously for 24 hours
DP, DM, ID low voltage short circuit
DP, DM or ID pins short circuited to GND in
any mode of TUSB1210 operation,
continuously for 24 hours
°C
0
V
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The product will have negligible reliability impact if voltage spikes of 5.5 V occur for a total (cumulative over lifetime) duration of 5
milliseconds.
Except VBAT input, VBUS, ID, DP, and DM pads
3.2
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
NOM
MAX
2.7
3.6
4.8
UNIT
VBAT
Battery supply voltage
VBAT
CERT
Battery supply voltage for USB 2.0 compliancy
(USB 2.0 certification)
VDDIO
Digital IO pin supply
1.71
1.98
V
TA
Ambient temperature range
–40
85
°C
3.3
When VDD33 is supplied internally
3.15
When VDD33 is shorted to VBAT externally
3.05
V
V
ESD Electrical Parameters
over operating free-air temperature range (unless otherwise noted)
MAX
UNIT
CDM
Charged-Device Model stress voltage
PARAMETER
All pads
500
V
HBM
Human-Body Model stress voltage
All pads
2000
V
10
TEST CONDITIONS
Electrical Characteristics
MIN
TYP
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
4
Clock System
4.1
USB PLL Reference Clock
The USB PLL block generates the clocks used to synchronize :
• the ULPI interface (60 MHz clock)
• the USB interface (depending on the USB data rate, 480 Mbps, 12 Mbps or 1.5 Mbps)
TUSB1210 requires an external reference clock which is used as an input to the 480 MHz USB PLL block.
Depending on the clock configuration, this reference clock can be provided either at REFCLK pin or at
CLOCK pin. By default CLK pin is configured as an input.
Two clock configurations are possible:
• Input clock configuration (see Section 4.2)
• Output clock configuration (see Section 4.3)
4.2
ULPI Input Clock Configuration
In this mode REFCLK must be externally tied to GND. CLOCK remains configured as an input.
When the ULPI interface is used in “input clock configuration”, i.e., the 60 MHz ULPI clock is provided to
TUSB1210 on Clock pin, then this is used as the reference clock for the 480 MHz USB PLL block.
Table 4-1. Electrical Characteristics: Clock Input
PARAMETER
TEST CONDITIONS
Clock input duty cycle
fCLK
TYP
40
Clock nominal frequency
MAX
UNIT
60
60
Clock input rise/fall time
4.3
MIN
In % of clock period tCLK ( = 1/fCLK )
%
MHz
10
%
Clock input frequency accuracy
250
ppm
Clock input integrated jitter
600
ps rms
ULPI Output Clock Configuration
In this mode a reference clock must be externally provided on REFCLK pin When an input clock is
detected on REFCLK pin then CLK will automatically change to an output, i.e., 60 MHz ULPI clock is
output by TUSB1210 on CLK pin.
Two reference clock input frequencies are supported. REFCLK input frequency is communicated to
TUSB1210 via a configuration pin, CFG, see fREFCLK in Table 8-1 for frequency correspondence.
TUSB1210 supports square-wave reference clock input only. Reference clock input must be square-wave
of amplitude in the range 3.0 V to 3.6 V.
Table 4-2. Electrical Characteristics: REFCLK
PARAMETER
TEST CONDITIONS
REFCLK input duty cycle
fREFCLK
REFCLK nominal frequency
REFCLK input rise/fall time
MIN
TYP
40
UNIT
60
When CFG pin is tied to GND
19.2
When CFG pin is tied to VDDIO
26
In % of clock period tREFCLK ( =
1/fREFCLK )
MAX
%
MHz
20
%
REFCLK input frequency accuracy
250
ppm
REFCLK input integrated jitter
600
ps rms
Clock System
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
11
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
4.4
www.ti.com
Clock 32 kHz
An internal clock generator running at 32 kHz has been implemented to provide a low-speed, low-power
clock to the system
Table 4-3. Performances
PARAMETER
Output duty cycle
TEST CONDITIONS
Input duty cycle 40–60%
Output frequency
4.5
MIN
TYP
48
50
52
MAX
UNIT
%
23
32
38
kHz
Reset
All logic is reset if CS = 0 or VBAT are not present.
All logic (except 32 kHz logic) is reset if VDDIO is not present.
PHY logic is reset when any supplies are not present (VDDIO, VDD15, VDD18, VDD33) or if RESETB pin is low.
TUSB1210 may be reset manually by toggling the RESETB pin to GND for at lease 200 ns.
If manual reset via RESETB is not required then RESETB pin may be tied to VDDIO permanently.
12
Clock System
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
5
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Power Module
This chapter describes the electrical characteristics of the voltage regulators and timing characteristics of
the supplies digitally controlled within the TUSB1210.
5.1
Power Providers
Table 5-1. Summary of TUSB1210 Power Providers (1)
USAGE
TYPE
TYPICAL
VOLTAGE (V)
MAXIMUM
CURRENT (mA)
VDD15
Internal
LDO
1.5
50
VDD18
External
LDO
1.8
30
VDD33
Internal
LDO
3.1
15
NAME
(1)
5.1.1
VDD33 may be supplied externally, or by shorting the VDD33 pin to VBAT pin provided VBAT min is in
range [3.2 V : 3.6 V]. Note that the VDD33 LDO will always power-on when the chip is enabled,
irrespective of whether VDD33 is supplied externally or not. In the case the VDD33 pin is not supplied
externally in the application, the electrical specs for this LDO are provided below.
VDD33 Regulator
The VDD33 internal LDO regulator powers the USB PHY, charger detection, and OTG functions of the USB
subchip inside TUSB1210. Table 5-2 describes the regulator characteristics.
VDD33 regulator takes its power from VBAT.
Since the USB2.0 standard requires data lines to be biased with pullups biased from a supply greater than
3 V, and since VDD33 regulator has an inherent voltage drop from its input, VBAT, to its regulated output,
TUSB1210 will not meet USB 2.0 Standard if operated from a battery whose voltage is lower than 3.3 V.
Table 5-2. VDD33 Internal LDO Regulator Characteristics
PARAMETER
VINVDD33
VVDD33
IVDD33
5.1.2
Input voltage
Output voltage
Rated output current
TEST CONDITIONS
MIN
TYP
MAX
VVDD33 typ + 0.2
3.6
4.5
VUSB3V3_VSEL = ‘000
2.4
2.5
2.6
VUSB3V3_VSEL = ‘001
2.65
2.75
2.85
VUSB3V3_VSEL = ‘010
2.9
3.0
3.1
VUSB3V3_VSEL = ‘011 (default)
3.0
3.1
3.2
VUSB3V3_VSEL = ‘100
3.1
3.2
3.3
VUSB3V3_VSEL = ‘101
3.2
3.3
3.4
VUSB3V3_VSEL = ‘110
3.3
3.4
3.5
VUSB3V3_VSEL = ‘111
3.4
3.5
3.6
VBAT USB
ON mode,
VBAT USB
Active mode
15
Suspend/reset mode
1
UNIT
V
V
mA
VDD18 Supply
The VDD18 supply is powered externally at the VDD18 pin. See Table 8-1 for external components.
5.1.3
VDD15 Regulator
The VDD15 internal LDO regulator powers the USB subchip inside TUSB1210. Table 5-3 describes the
regulator characteristics.
Power Module
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
13
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
Table 5-3. VDD15 Internal LDO Regulator Characteristics
PARAMETER
VIN
TEST CONDITIONS
MIN
TYP
MAX
Input voltage
On mode, VIN VDD15 = VBAT
2.7
3.6
4.5
VVDD15
Output voltage
VINVDD15 min – VINVDD15 max
1.45
1.56
1.65
IVDD15
Rated output current
On mode
5.2
VDD15
UNIT
30
V
V
mA
Power Consumption
Table 5-4 describes the power consumption depending on the use cases.
NOTE
The typical power consumption is obtained in the nominal operating conditions and with the
TUSB1210 standalone.
Table 5-4. Power Consumption
MODE
CONDITIONS
SUPPLY
TYPICAL
CONSUMPTION
IVBAT
8
OFF Mode
VBAT = 3.6 V, VDDIO = 1.8 V, VDD18
= 1.8 V, CS = 0 V
IVDDIO
3
IVDD18
5
Suspend Mode
HS USB Operation
(Synchronous Mode)
FS USB Operation
(Synchronous Mode)
Reset Mode
14
VBUS = 5 V, VBAT = 3.6 V, VDDIO =
1.8 V, No clock
VBAT = 3.6 V, VDDIO = 1.8 V, VDD18
= 1.8 V, active USB transfer
VBAT = 3.6 V, VDDIO = 1.8 V, active
USB transfer
RESETB = 0 V, VBUS = 5 V, VBAT
= 3.6 V, VDDIO = 1.8 V, No clock
ITOTAL
16
IVBAT
204
IVDDIO
3
IVDD18
3
ITOTAL
210
IVBAT
24.6
IVDDIO
1.89
IVDD18
21.5
ITOTAL
48
IVBAT
25.8
IVDDIO
1.81
IVDD18
4.06
ITOTAL
31.7
IVBAT
237
IVDDIO
3
IVDD18
3
ITOTAL
243
Power Module
UNIT
µA
µA
mA
mA
µA
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
5.3
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Power Management
5.3.1
5.3.1.1
Power On Sequence
Timing Diagram
VDDIO, VDD18
ACTIVE
COLDRST
HWRST
OFF
NOPWR
VBAT , VDD33
IORST
CS
TVBBDET (10us)
ICACT
TBGAP (2ms)
BGOK
TPWONVDD15 (100us)
VDD15
DIGPOR
CK32K
TCK32K_PWON (125us)
CK32KOK
RESETN_PWR
MNTR_(VDD18,VIO)_OK
TDELRSTPWR (61us)
TDELMNTRVIOEN (91.5us)
TMNTR (183.1us)
TDELVDD33EN (91.5us)
TMNTR (183.1us)
MNTR_VDD33_OK
(input 60M) CLOCK
RESETB
TDELRESETB (244.1us)
TPLL (300us)
PLL 480M LOCKED
DIR
TDEL_CS_SUPPLYOK (2.84ms)
TDEL_RST_DIR (0.54ms)
Figure 5-1. TUSB1210 Power-Up Timing (ULPI Clock Input Mode)
Power Module
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
15
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
5.3.2
www.ti.com
Timers and Debounce
TYP
MAX
UNIT
TDEL_CS_SUPPLYOK
Chip-select-to-supplies OK delay
PARAMETER
COMMENTS
MIN
2.84
4.10
ms
TDEL_RST_DIR
RESETB to PHY PLL locked and DIR
falling-edge delay
0.54
0.647
ms
TVBBDET
VBAT detection delay
TBGAP
Bandgap power-on delay
TPWONVDD15
10
us
2
ms
VDD15 power-on delay
100
us
TPWONCK32K
32-KHz RC-OSC power-on delay
125
us
TDELRSTPWR
Power control reset delay
61
us
TDELMNTRVIOEN
Monitor enable delay
91.5
us
TMNTR
Supply monitoring debounce
183.1
us
TDELVDD33EN
VDD33 LDO enable delay
93.75
us
TDELRESETB
RESETB internal delay
244.1
us
TPLL
PLL lock time
300
us
16
Power Module
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
6
USB Connectivity
6.1
Timing Parameter Definitions
The timing parameter symbols used in the timing requirement and switching characteristic tables are
created in accordance with JEDEC Standard 100. To shorten the symbols, some pin names and other
related terminologies have been abbreviated as shown in Table 6-1.
Table 6-1. Timing Parameter Definitions
LOWERCASE SUBSCRIPTS
SYMBOL
PARAMETER
C
Cycle time (period)
D
Delay time
Dis
Disable time
En
Enable time
H
Hold time
Su
Setup time
START
Start bit
T
Transition time
V
Valid time
W
Pulse duration (width)
X
Unknown, changing, or don't care level
H
High
L
Low
V
Valid
IV
Invalid
AE
Active edge
FE
First edge
LE
Last edge
Z
6.2
High impedance
Interface Target Frequencies
Table Table 6-2 assumes testing over the recommended operating conditions.
Table 6-2. TUSB1210 Interface Target Frequencies
IO
INTERFACE
USB
6.3
INTERFACE DESIGNATION
Universal
serial bus
High speed
TARGET
FREQUENCY
1.5 V
480 Mbits/s
Full speed
12 Mbits/s
Low speed
1.5 Mbits/s
USB Transceiver
The TUSB1210 device includes a universal serial bus (USB) on-the-go (OTG) transceiver that supports
USB 480 Mb/s high-speed (HS), 12 Mb/s full-speed (FS), and USB 1.5 Mb/s low-speed (LS) through a 12pin UTMI+ low pin interface (ULPI).
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
17
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
NOTE
LS device mode is not allowed by a USB2.0 HS capable PHY, therefore it is not supported
by TUSB1210. This is clearly stated in USB2.0 standard Chapter 7, page 119, second
paragraph: “A high-speed capable upstream facing transceiver must not support low-speed
signaling mode..” There is also some related commentary in Chapter 7.1.2.3.
6.3.1
TUSB1210 Modes vs ULPI Pin Status
Table 6-3, Table 6-4, and Table 6-5 show the status of each of the 12 ULPI pins including input/output
direction and whether output pins are driven to ‘0’ or to ‘1’, or pulled up/pulled down via internal
pullup/pulldown resistors.
Note that pullup/pulldown resistors are automatically replaced by driven ‘1’/’0’ levels respectively once
internal IORST is released, with the exception of the pullup on STP which is maintained in all modes.
Pin assignment changes in ULPI 3-pin serial mode, ULPI 6-pin serial mode, and UART mode. Unused
pins are tied low in these modes as shown below.
Table 6-3. TUSB1210 Modes vs ULPI Pin Status:ULPI Synchronous Mode Power-Up
ULPI SYNCHRONOUS MODE POWER-UP
UNTIL IORST RELEASE
PIN
NO.
PIN NAME
DIR
PU/PD
26
CLOCK
Hiz
31
DIR
Hiz
PLL OFF
PLL ON + STP HIGH
DIR
PU/PD
PD
I
PU
O, (‘1’)
PLL ON + STP LOW
DIR
PU/PD
DIR
PU/PD
PD
IO
-
IO
-
-
O, (‘0’)
-
O
-
2
NXT
Hiz
PD
O, (‘0’)
-
O, (‘0’)
-
O
-
29
STP
Hiz
PU
I
PU
I
PU
I
PU
3
DATA0
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
4
DATA1
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
5
DATA2
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
6
DATA3
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
7
DATA4
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
9
DATA5
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
10
DATA6
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
13
DATA7
Hiz
PD
O, (‘0’)
-
I
PD
IO
-
Table 6-4. TUSB1210 Modes vs ULPI Pin Status: USB Suspend Mode
LINK / EXTERNAL RECOMMENDED
SETTING DURING SUSPEND MODE
SUSPEND MODE
PIN NO.
PIN NAME
26
31
2
(1)
18
DIR
PU/PD
DIR
PU/PD
CLOCK
I
-
O
-
DIR
O, (‘1’)
-
I
-
NXT
O, (‘0’)
-
I
-
PU
(1)
29
STP
I
O, (‘0’)
-
3
DATA0
O,
(LINESTATE0)
-
I
-
4
DATA1
O,
(LINESTATE1)
-
I
-
5
DATA2
O, (‘0’)
-
I
-
6
DATA3
O, (INT)
-
I
-
Can be disabled by software before entering Suspend Mode to reduce current consumption
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Table 6-4. TUSB1210 Modes vs ULPI Pin Status: USB Suspend Mode
(continued)
LINK / EXTERNAL RECOMMENDED
SETTING DURING SUSPEND MODE
SUSPEND MODE
PIN NO.
PIN NAME
DIR
PU/PD
DIR
PU/PD
7
DATA4
O, (‘0’)
-
I
-
9
DATA5
O, (‘0’)
-
I
-
10
DATA6
O, (‘0’)
-
I
-
13
DATA7
O, (‘0’)
-
I
-
Table 6-5. TUSB1210 Modes vs ULPI Pin Status: ULPI 6-Pin Serial Mode and UART Mode
ULPI 6-PIN SERIAL MODE
ULPI 3-PIN SERIAL MODE
UART MODE
PIN NO.
PIN NAME
DIR
PU/PD
PIN NAME
DIR
PU/PD
PIN NAME
DIR
PU/PD
26
CLOCK (1)
IO
-
CLOCK (1)
IO
-
CLOCK (1)
IO
-
31
DIR
O
-
DIR
O
-
DIR
O
-
2
NXT
O
-
NXT
O
-
NXT
O
-
29
STP
I
PU
STP
I
PU
STP
I
PU
3
TX_ENABLE
I
-
TX_ENABLE
I
-
TXD
I
-
4
TX_DAT
I
-
DAT
IO
-
RXD
IO
-
5
TX_SE0
I
-
SE0
IO
-
tie low
O
-
6
INT
O
-
INT
O
-
INT
O
-
7
RX_DP
O
-
tie low
O
-
tie low
O
-
9
RX_DM
O
-
tie low
O
-
tie low
O
10
RX_RCV
O
-
tie low
O
-
tie low
O
13
tie low
O
-
tie low
O
-
tie low
O
6.3.2
-
ULPI Interface Timing
Table 6-6. ULPI Interface Timing
INPUT CLOCK
PARAMETER
MIN
TSC,TSD
Set-up time (control in, 8-bit data in)
TSC,THD
Hold time (control in, 8-bit data in)
TDC,TDD
Output delay (control out, 8-bit data out)
6.3.3
OUTPUT CLOCK
MAX
MIN
3
1.5
MAX
UNIT
6
0
6
ns
ns
9
ns
PHY Electrical Characteristics
The PHY is the physical signaling layer of the USB 2.0. It essentially contains all the drivers and receivers
required for physical data and protocol signaling on the DP and DM lines.
The PHY interfaces to the USB controller through a standard 12-pin digital interface called UTMI+ low pin
interface (ULPI).
The transmitters and receivers inside the PHY are classified into two main classes.
• The full-speed (FS) and low-speed (LS) transceivers. These are the legacy USB1.x transceivers.
• The HS (HS) transceivers
In order to bias the transistors and run the logic, the PHY also contains reference generation circuitry
which consists of:
• A DPLL which does a frequency multiplication to achieve the 480-MHz low-jitter lock necessary for
USB and also the clock required for the switched capacitor resistance block.
• A switched capacitor resistance block which is used to replicate an external resistor on chip.
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
19
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
Built-in pullup and pulldown resistors are used as part of the protocol signaling.
Apart from this, the PHY also contains circuitry which protects it from accidental 5-V short on the DP and
DM lines.
6.3.3.1
LS/FS Single-Ended Receivers
In addition to the differential receiver, there is a single-ended receiver (SE–, SE+) for each of the two data
lines D+/–. The main purpose of the single-ended receivers is to qualify the D+ and D– signals in the fullspeed/low-speed modes of operation.
Table 6-7. LS/FS Single-Ended Receivers
PARAMETER
COMMENTS
MIN
TYP
MAX
–2
0
2
UNIT
USB single-ended receivers
SKWVP_VM
Skew between VP and VM
VSE_HYS
Single-ended hysteresis
VIH
High (driven)
VIL
Low
VTH
Switching threshold
6.3.3.2
Driver outputs unloaded
ns
50
mV
2
V
0.8
V
2
V
0.8
LS/FS Differential Receiver
A differential input receiver (Rx) retrieves the LS/FS differential data signaling. The differential voltage on
the line is converted into digital data by a differential comparator on DP/DM. This data is then sent to a
clock and data recovery circuit which recovers the clock from the data. An additional serial mode exists in
which the differential data is directly output on the RXRCV pin.
Table 6-8. LS/FS Differential Receiver
PARAMETER
COMMENTS
MIN
VDI
Differential input sensitivity
Ref. USB2.0
200
VCM
Differential Common mode range
Ref. USB2.0
0.8
6.3.3.3
TYP
MAX
UNIT
mV
2.5
V
LS/FS Transmitter
The USB transceiver (Tx) uses a differential output driver to drive the USB data signal D+/– onto the USB
cable. The driver's outputs support 3-state operation to achieve bidirectional half-duplex transactions.
Table 6-9. LS Transmitter
PARAMETER
COMMENTS
MIN
TYP
MAX
UNIT
VOL
Low
Ref. USB2.0
0
300
mV
VOH
High (driven)
Ref. USB2.0
2.8
3.6
V
VCRS
Output signal crossover voltage
Ref. USB2.0, covered by
eye diagram
1.3
2
V
TFR
Rise time
Ref. USB2.0, covered by
eye diagram
75
300
ns
TFF
Fall time
75
300
ns
TFRFM
Differential rise and fall time matching
TFDRATE
Low-speed data rate
TDJ1
Source jitter total (including
frequency tolerance)
TDJ2
TFEOPT
20
Source SE0 interval of EOP
To next transition
For paired transitions
80
125
Ref. USB2.0, covered by
eye diagram
1.4775
1.5225
Ref. USB2.0, covered by
eye diagram
-25
25
-10
10
Ref. USB2.0, covered by
eye diagram
1.25
1.5
USB Connectivity
%
Mb/s
ns
us
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Table 6-9. LS Transmitter (continued)
PARAMETER
VCM
COMMENTS
Downstream eye diagram
Ref. USB2.0, covered by
eye diagram
Differential common mode range
Ref. USB2.0
MIN
0.8
TYP
MAX
2.5
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
UNIT
V
21
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
Table 6-10. FS Transmitter
PARAMETER
COMMENTS
MIN
TYP
MAX
UNIT
VOL
Low
Ref. USB2.0
0
300
mV
VOH
High (driven)
Ref. USB2.0
2.8
3.6
V
VCRS
Output signal crossover voltage
Ref. USB2.0, covered by eye
diagram
1.3
2
V
tFR
Rise time
Ref. USB2.0
4
20
ns
tFF
Fall time
Ref. USB2.0
4
20
ns
tFRFM
Differential rise and fall time matching
Ref. USB2.0, covered by eye
diagram
90
111.1
1
%
ZDRV
Driver output resistance
Ref. USB2.0
28
44
TFDRATE
Full-speed data rate
Ref. USB2.0, covered by eye
diagram
11.97
12.03
TDJ1
Source jitter total (including
frequency tolerance)
Ref. USB2.0, covered by eye
diagram
-2
2
TDJ2
-1
1
TFEOPT
Source SE0 interval of EOP
Ref. USB2.0, covered by eye
diagram
160
175
Downstream eye diagram
Ref. USB2.0, covered by eye
diagram
To next transition
For paired transitions
Ω
Mb/s
ns
ns
Upstream eye diagram
6.3.3.4
HS Differential Receiver
The HS receiver consists of the following blocks:
A differential input comparator to receive the serial data
• A squelch detector to qualify the received data
• An oversampler-based clock data recovery scheme followed by a NRZI decoder, bit unstuffing, and
serial-to-parallel converter to generate the ULPI DATAOUT
Table 6-11. HS Differential Receiver
COMMENTS
MIN
VHSSQ
High-speed squelch detection threshold
(differential signal amplitude)
PARAMETER
Ref. USB2.0
100
VHSDSC
High-speed disconnect detection threshold
(differential signal amplitude)
Ref. USB2.0
High-speed differential input signaling levels
Ref. USB2.0, specified by eye pattern
templates
High-speed data signaling common mode
voltage range (guidelines for receiver)
Ref. USB2.0
Receiver jitter tolerance
Ref. USB2.0, specified by eye pattern
templates
VHSCM
6.3.3.5
525
TYP
MAX
UNIT
150
mV
625
mV
mV
-50
500
mV
150
ps
HS Differential Transmitter
The HS transmitter is always operated via the ULPI parallel interface. The parallel data on the interface is
serialized, bit stuffed, NRZI encoded, and transmitted as a dc output current on DP or DM depending on
the data. Each line has an effective 22.5-Ω load to ground, which generates the voltage levels for
signaling.
A disconnect detector is also part of the HS transmitter. A disconnect on the far end of the cable causes
the impedance seen by the transmitter to double thereby doubling the differential amplitude seen on the
DP/DM lines.
22
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Table 6-12. HS Transmitter
PARAMETER
COMMENTS
MIN
TYP MAX
UNIT
VHSOI
High-speed idle level
Ref. USB2.0
-10
10
mV
VHSOH
High-speed data signaling high
Ref. USB2.0
360
440
mV
VHSOL
High-speed data signaling low
Ref. USB2.0
-10
10
mV
VCHIRPJ
Chirp J level (differential voltage)
Ref. USB2.0
700
1100
mV
VCHIRPK
Chirp K level (differential voltage)
Ref. USB2.0
-900
-500
mV
THSR
Rise Time (10% - 90%)
Ref. USB2.0, covered by eye diagram
500
ps
THSR
Fall time (10% - 90%)
Ref. USB2.0, covered by eye diagram
500
ps
ZHSDRV
Driver output resistance (which also serves as
high-speed termination)
Ref. USB2.0
40.5
49.5
Ω
479.76
480.
24
Mb/s
THSDRAT High-speed data range
6.3.3.6
Ref. USB2.0, covered by eye diagram
Data source jitter
Ref. USB2.0, covered by eye diagram
Downstream eye diagram
Ref. USB2.0, covered by eye diagram
Upstream eye diagram
Ref. USB2.0, covered by eye diagram
UART Transceiver
In this mode, the ULPI data bus is redefined as a 2-pin UART interface, which exchanges data through a
direct access to the FS/LS analog transmitter and receiver.
Table 6-13. USB UART Interface Timing Parameters
PARAMETER
MIN
tPH_DP_CON
Phone D+ connect time
100
tPH_DISC_DET
Phone D+ disconnect time
150
fUART_DFLT
Default UART signaling rate (typical rate)
MAX
UNIT
ms
ms
9600
bps
Figure 6-1. USB UART Data Flow
Table 6-14. CEA-2011/UART Transceiver
PARAMETER
COMMENTS
MIN
TYP
MAX
UNIT
2.4
3.3
3.6
V
0.1
0.4
V
UART Transmitter CEA-2011
tPH_UART_EDGE
Phone UART edge rates
DP_PULLDOWN asserted
VOH_SER
Serial interface output high
ISOURCE = 4 mA
1
VOL_SER
Serial interface output low
ISINK = –4 mA
0
DP_PULLDOWN asserted
2
Μs
UART Receiver CEA-2011
VIH_SER
Serial interface input high
VIL_SER
Serial interface input low
VTH
Switching threshold
DP_PULLDOWN asserted
0.8
V
0.8
V
2
V
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
23
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
Table 6-15. Pullup/Pulldown Resistors
PARAMETER
COMMENTS
MIN
TYP
MAX
UNIT
0.9
1.1
1.575
kΩ
1.425
2.2
3.09
RPUI
Bus pullup resistor on upstream port
(idle bus)
Bus idle
RPUA
Bus pullup resistor on upstream port
(receiving)
Bus driven/driver's outputs unloaded
High (floating)
Pullups/pulldowns on both DP and
DM lines
Phone D+ pullup voltage
Driver's outputs unloaded
3
Phone D+/– pulldown
Driver's outputs unloaded
14.25
High (floating)
Pullups/pulldowns on both DP and
DM lines
VIHZ
VPH_DP_UP
2.7
3.6
V
3.3
3.6
V
18
24.8
kΩ
3.6
V
75
pF
0.342
V
Pulldown resistors
RPH_DP_DWN
RPH_DM_DWN
VIHZ
2.7
D+/– Data line
CINUB
Upstream facing port
VOTG_DATA_LK
G
On-the-go device leakage
22
[2]
Input impedance exclusive of
pullup/pulldown
ZINP
6.3.4
[1.0]
Driver's outputs unloaded
300
kΩ
OTG Electrical Characteristics
The on-the-go (OTG) block integrates three main functions:
• The USB plug detection function on VBUS and ID
• The ID resistor detection
• The VBUS level detection
Table 6-16. OTG VBUS Electrical
PARAMETER
COMMENTS
MIN
TYP
MAX
UNIT
VBUS Comparators
VA_SESS_VLD
A-device session valid
0.8
1.4
2.0
V
VA_VBUS_VLD
A-device VBUS valid
4.4
4.5
4.625
V
VB_SESS_END
B-device session end
0.2
0.5
0.8
V
VB_SESS_VLD
B-device session valid
2.1
2.4
2.7
V
100
kΩ
VBUS Line
RA_BUS_IN
A-device VBUS input impedance to
ground
SRP (VBUS pulsing) capable A-device not
driving VBUS
RB_SRP_DWN
B-device VBUS SRP pulldown
5.25 V / 8 mA, Pullup voltage = 3 V
0.656
10
RB_SRP_UP
B-device VBUS SRP pullup
(5.25 V – 3 V) / 8 mA, Pullup voltage = 3 V
0.281
1
tRISE_SRP_UP_MAX
B-device VBUS SRP rise time
maximum for OTG-A communication
0 to 2.1 V with < 13 μF load
tRISE_SRP_UP_MIN
B-device VBUS SRP rise time
minimum for standard host
connection
24
40
70
kΩ
2
kΩ
TBD
ms
0.8 to 2.0 V with > 97 μF load
TBD
USB Connectivity
ms
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Table 6-17. OTG ID Electrical
PARAMETER
COMMENTS
MIN
TYP
12
20
MAX
UNIT
ID Comparators — ID External Resistors Specifications
RID_GND
ID ground comparator
ID_GND interrupt
RID_FLOAT
ID Float comparator
ID_FLOAT interrupt
200
28
kΩ
500
kΩ
286
kΩ
3.2
V
5.25
V
ID Line
RPH_ID_UP
Phone ID pullup to VPH_ID_UP
ID unloaded (VRUSB)
70
VPH_ID_UP
Phone ID pullup voltage
Connected to VRUSB
2.5
ID line maximum voltage
90
USB Connectivity
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
25
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
7
I/O Electrical Characteristics
7.1
Analog I/O Electrical Characteristics
Table 7-1. Electrical Characteristics: Analog Output Pins
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
CPEN Output Pin
VOLCPEN CPEN low-level output voltage
IOL = 3 mA
VOHCPEN CPEN high-level output voltage
IOH = -3 mA
7.2
0.3
VDD33-0.3
V
V
Digital I/O Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
VOL (V)
PIN
NAME
MAX
MIN
CLOCK
0.45
STP
0.45
DIR
VIL (V)
MAX
MIN
VIH (V)
MAX
MAX
FREQ
(MHz)
MAX
LOAD
(pF)
OUTPUT
MODE
MAX
RISE TIME
(ns)
MAX
FALL TIME
(ns)
MAX
MIN
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
60
10
1
1
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
NXT
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA0
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA1
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA2
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA3
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA4
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA5
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA6
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
DATA7
0.45
VDDIO-0.45
0.35´VDDIO
0.65´VDDIO
30
10
1
1
7.3
MIN
VOH (V)
Electrical Characteristics: Digital IO Pins (Non-ULPI)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
0.35 *
VDDIO
V
CS, CFG, RESETB Input Pins
VIL
Maximum low-level input voltage
VIH
Minimum high-level input voltage
0.65*VDDIO
V
0.2
μs
RESETB Input Pin Timing Spec
tw(POR)
Internal power-on reset pulse
width
tw(RESET)
External RESETB pulse width
26
Applied to external RESETB pin when
CLOCK is toggling.
I/O Electrical Characteristics
8
CLOCK
cycles
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
8
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
External Components
Table 8-1. TUSB1210 External Components
FUNCTION
COMPONENT
REFERENCE
VALUE
NOTE
LINK
VDDIO
Capacitor
CVDDIO
100 nF
Suggested value, application
dependent
Figure 10-1
VDD33
Capacitor
CVDD33
2.2 μF
Range: [0.45 μF : 6.5 μF] ,
ESR = [0 : 600 mΩ] for f> 10 kHz
Figure 10-1
VDD15
Capacitor
CVDD15
2.2 μF
Range: [0.45 μF : 6.5 μF] ,
ESR = [0 : 600 mΩ] for f> 10 kHz
Figure 10-1
VDD18
Capacitor
Ext 1.8V supply
100 nF
Suggested value, application
dependent
Figure 10-1
VBAT
Capacitor
CBYP
100 nF (1)
Range: [0.45 μF : 6.5 μF] ,
ESR = [0 : 600 mΩ] for f> 10 kHz
Figure 10-1
VBUS
Capacitor
CVBUS
See table 1.2
Place close to USB connector
Figure 10-1
CVDD18
(1)
Recommended value but 2.2 uF may be sufficient in some applications
Table 8-2. TUSB1210 VBUS Capacitors
FUNCTION
COMPONENT
REFERENCE
VALUE
VBUS - HOST
Capacitor
CVBUS
>120 μF
NOTE
LINK
VBUS – DEVICE
Capacitor
CVBUS
4.7 μF
Range: 1.0 μF to 10.0 μF
Figure 10-1
VBUS - OTG
Capacitor
CVBUS
4.7 μF
Range: 1.0 μF to 6.5 μF
Figure 10-1
Figure 10-1
External Components
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
27
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9
Register Map
9.1
TUSB1210 Product
www.ti.com
Table 9-1. USB Register Summary
28
REGISTER NAME
TYPE
REGISTER WIDTH
(BITS)
PHYSICAL
ADDRESS
VENDOR_ID_LO
R
8
0x00
VENDOR_ID_HI
R
8
0x01
PRODUCT_ID_LO
R
8
0x02
PRODUCT_ID_HI
R
8
0x03
FUNC_CTRL
RW
8
0x04
FUNC_CTRL_SET
RW
8
0x05
FUNC_CTRL_CLR
RW
8
0x06
IFC_CTRL
RW
8
0x07
0x08
IFC_CTRL_SET
RW
8
IFC_CTRL_CLR
RW
8
0x09
OTG_CTRL
RW
8
0x0A
OTG_CTRL_SET
RW
8
0x0B
OTG_CTRL_CLR
RW
8
0x0C
USB_INT_EN_RISE
RW
8
0x0D
USB_INT_EN_RISE_SET
RW
8
0x0E
USB_INT_EN_RISE_CLR
RW
8
0x0F
USB_INT_EN_FALL
RW
8
0x10
USB_INT_EN_FALL_SET
RW
8
0x11
USB_INT_EN_FALL_CLR
RW
8
0x12
USB_INT_STS
R
8
0x13
USB_INT_LATCH
R
8
0x14
DEBUG
R
8
0x15
SCRATCH_REG
RW
8
0x16
SCRATCH_REG_SET
RW
8
0x17
SCRATCH_REG_CLR
RW
8
0x18
Reserved
R
8
0x19 0x2E
ACCESS_EXT_REG_SET
RW
8
0x2F
Reserved
R
8
0x30 0x3C
VENDOR_SPECIFIC1
RW
8
0x3D
VENDOR_SPECIFIC1_SET
RW
8
0x3E
VENDOR_SPECIFIC1_CLR
RW
8
0x3F
VENDOR_SPECIFIC2
RW
8
0x80
VENDOR_SPECIFIC2_SET
RW
8
0x81
VENDOR_SPECIFIC2_CLR
RW
8
0x82
VENDOR_SPECIFIC1_STS
R
8
0x83
VENDOR_SPECIFIC1_LATCH
R
8
0x84
VENDOR_SPECIFIC3
RW
8
0x85
VENDOR_SPECIFIC3_SET
RW
8
0x86
VENDOR_SPECIFIC3_CLR
RW
8
0x87
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
9.1.1
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
VENDOR_ID_LO
ADDRESS OFFSET
0x00
PHYSICAL ADDRESS
0x00
DESCRIPTION
Lower byte of vendor ID supplied by USB-IF (TI Vendor ID = 0x0451)
TYPE
R
INSTANCE
USB_SCUSB
WRITE LATENCY
7
6
5
4
3
2
1
0
VENDOR_ID
9.1.2
BITS
FIELD NAME
7:00
VENDOR_ID
DESCRIPTION
TYPE
RESET
R
0x51
VENDOR_ID_HI
ADDRESS OFFSET
0x01
PHYSICAL ADDRESS
0x01
DESCRIPTION
Upper byte of vendor ID supplied by USB-IF (TI Vendor ID = 0x0451)
TYPE
R
INSTANCE
USB_SCUSB
WRITE LATENCY
7
6
5
4
3
2
1
0
VENDOR_ID
9.1.3
BITS
FIELD NAME
7:00
VEN DOR_ID
DESCRIPTION
TYPE
RESET
R
0x04
PRODUCT_ID_LO
ADDRESS OFFSET
0x02
PHYSICAL ADDRESS
0x02
DESCRIPTION
Lower byte of Product ID supplied by Vendor (TUSB1210 Product ID is
0x1507).
TYPE
R
INSTANCE
USB_SCUSB
WRITE LATENCY
7
6
5
4
3
2
1
0
PRODUCT_ID
BITS
7:00
FIELD NAME
DESCRIPTION
PRODUCT_ID
TYPE
RESET
R
0x07
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
29
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9.1.4
www.ti.com
PRODUCT_ID_HI
ADDRESS OFFSET
0x03
PHYSICAL ADDRESS
0x03
DESCRIPTION
Upper byte of Product ID supplied by Vendor (TUSB1210 Product ID is
0x1507).
TYPE
R
INSTANCE
USB_SCUSB
WRITE LATENCY
7
6
5
4
3
2
1
0
PRODUCT_ID
BITS
FIELD NAME
7:00
9.1.5
DESCRIPTION
PRODUCT_ID
TYPE
RESET
R
0x15
FUNC_CTRL
ADDRESS OFFSET
0x04
PHYSICAL ADDRESS
0x04
DESCRIPTION
Controls UTMI function settings of the PHY.
TYPE
RW
INSTAN
CE
USB_SCUSB
BITS
SUSPENDM
RESET
FIELD NAME
7
Reserved
6
SUSPENDM
5
RESET
4
3
2
1
0
XCVRSELECT
5
TERMSELECT
6
OPMODE
7
Reserved
WRITE LATENCY
DESCRIPTION
TYPE
RESET
R
0
Active low PHY suspend. Put PHY into Low Power Mode. In Low Power
Mode the PHY power down all blocks except the full speed receiver, OTG
comparators, and the ULPI interface pins. The PHY automatically set this bit
to '1' when Low Power Mode is exited.
RW
1
Active high transceiver reset. Does not reset the ULPI interface or ULPI
register set.
RW
0
RW
0x0
RW
0
Once set, the PHY asserts the DIR signal and reset the UTMI core. When the
reset is completed, the PHY de-asserts DIR and clears this bit. After deasserting DIR, the PHY re-assert DIR and send an RX command update.
Note: This bit is auto-cleared, this explain why it can't be read at '1'.
4:03
2
30
OPMODE
TERMSELECT
Select the required bit encoding style during transmit
0x0:
Normal operation
0x1:
Non-driving
0x2:
Disable bit-stuff and NRZI encoding
0x3:
Reserved (No SYNC and EOP generation feature not supported)
Controls the internal 1.5Kohms pull-up resistor and 45ohms HS terminations.
Control over bus resistors changes depending on XcvrSelect, OpMode,
DpPulldown and DmPulldown.
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
BITS
1:00
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
FIELD NAME
XCVRSELECT
DESCRIPTION
Select the required transceiver speed.
0x0:
Enable HS transceiver
0x1:
Enable FS transceiver
0x2:
Enable LS transceiver
0x3:
Enable FS transceiver for LS packets
TYPE
RESET
RW
0x1
(FS preamble is automatically pre-pended)
9.1.6
FUNC_CTRL_SET
ADDRESS OFFSET
0x05
PHYSICAL ADDRESS
0x05
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the func_ctrl register with read/set-only property (write '1' to
set a particular bit, a write '0' has no-action).
TYPE
RW
9.1.7
SUSPENDM
RESET
4
3
2
1
0
XCVRSELECT
5
TERMSELECT
6
OPMODE
7
Reserved
WRITE LATENCY
BITS
FIELD NAME
TYPE
RESET
7
Reserved
DESCRIPTION
R
0
6
SUSPENDM
RW
1
5
RESET
RW
0
4:03
OPMODE
RW
0x0
2
TERMSELECT
RW
0
1:00
XCVRSELECT
RW
0x1
FUNC_CTRL_CLR
ADDRESS OFFSET
0x06
PHYSICAL ADDRESS
0x06
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the func_ctrl register with read/clear-only property (write '1' to
clear a particular bit, a write '0' has no-action).
TYPE
RW
3
2
1
0
XCVRSELECT
4
TERMSELECT
5
OPMODE
6
RESET
Reserved
7
SUSPENDM
WRITE LATENCY
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
31
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9.1.8
www.ti.com
BITS
FIELD NAME
TYPE
RESET
7
Reserved
DESCRIPTION
R
0
6
SUSPENDM
RW
1
5
RESET
RW
0
4:03
OPMODE
RW
0x0
2
TERMSELECT
RW
0
1:00
XCVRSELECT
RW
0x1
IFC_CTRL
ADDRESS OFFSET
0x07
PHYSICAL ADDRESS
0x07
DESCRIPTION
Enables alternative interfaces and PHY features.
TYPE
RW
INSTANCE
USB_SCUSB
BITS
7
INDICATORPASSTHRU
INDICATORCOMPLEMENT
AUTORESUME
FIELD NAME
3
2
1
0
FSLSSERIALMODE_6PIN
4
FSLSSERIALMODE_3PIN
5
CARKITMODE
6
CLOCKSUSPENDM
7
INTERFACE_PROTECT_DISABLE
WRITE LATENCY
DESCRIPTION
INTERFACE_PROTECT Controls circuitry built into the PHY for protecting the ULPI interface when the
_DISABLE
link tri-states stp and data.
TYPE
RESET
RW
0
RW
0
RW
0
RW
1
RW
0
0b: Enables the interface protect circuit
1b: Disables the interface protect circuit
6
INDICATORPASSTHRU
Controls whether the complement output is qualified with the internal
vbusvalid comparator before being used in the VBUS State in the RXCMD.
0b: Complement output signal is qualified with the internal VBUSVALID
comparator.
1b: Complement output signal is not qualified with the internal VBUSVALID
comparator.
5
INDICATORCOMPLEM
ENT
Tells the PHY to invert EXTERNALVBUSINDICATOR input signal, generating
the complement output.
0b: PHY will not invert signal EXTERNALVBUSINDICATOR (default)
1b: PHY will invert signal EXTERNALVBUSINDICATOR
4
AUTORESUME
Enables the PHY to automatically transmit resume signaling.
Refer to USB specification 7.1.7.7 and 7.9 for more details.
0 = AutoResume disabled
1 = AutoResume enabled (default)
3
CLOCKSUSPENDM
Active low clock suspend. Valid only in Serial Modes. Powers down the
internal clock circuitry only. Valid only when SuspendM = 1b. The PHY must
ignore ClockSuspend when SuspendM = 0b. By default, the clock will not be
powered in Serial and Carkit Modes.
0b : Clock will not be powered in Serial and UART Modes.
1b : Clock will be powered in Serial and UART Modes.
32
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
BITS
2
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
FIELD NAME
CARKITMODE
DESCRIPTION
Changes the ULPI interface to UART interface. The PHY automatically clear
this field when UART mode is exited.
TYPE
RESET
RW
0
RW
0
RW
0
0b: UART disabled.
1b: Enable serial UART mode.
1
FSLSSERIALMODE_3PI Changes the ULPI interface to 3-pin Serial.
N
The PHY must automatically clear this field when serial mode is exited.
0b: FS/LS packets are sent using parallel interface
1b: FS/LS packets are sent using 4-pin serial interface
0
FSLSSERIALMODE_6PI Changes the ULPI interface to 6-pin Serial.
N
The PHY must automatically clear this field when serial mode is exited.
0b: FS/LS packets are sent using parallel interface
1b: FS/LS packets are sent using 6-pin serial interface
9.1.9
IFC_CTRL_SET
ADDRESS OFFSET
0x08
PHYSICAL ADDRESS
0x08
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the ifc_ctrl register with read/set-only property (write '1' to set
a particular bit, a write '0' has no-action).
TYPE
RW
INDICATORPASSTHRU
INDICATORCOMPLEMENT
AUTORESUME
3
2
1
0
FSLSSERIALMODE_6PIN
4
FSLSSERIALMODE_3PIN
5
CARKITMODE
6
CLOCKSUSPENDM
7
INTERFACE_PROTECT_DISABLE
WRITE LATENCY
BITS
FIELD NAME
TYPE
RESET
7
INTERFACE_PROTECT_DISABLE
DESCRIPTION
RW
0
6
INDICATORPASSTHRU
RW
0
5
INDICATORCOMPLEMENT
RW
0
4
AUTORESUME
RW
1
3
CLOCKSUSPENDM
RW
0
2
CARKITMODE
RW
0
1
FSLSSERIALMODE_3PIN
RW
0
0
FSLSSERIALMODE_6PIN
R
0
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
33
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
9.1.10 IFC_CTRL_CLR
ADDRESS OFFSET
0x09
PHYSICAL ADDRESS
0x09
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the ifc_ctrl register with read/clear-only property (write '1' to
clear a particular bit, a write '0' has no-action).
TYPE
RW
5
4
3
2
IN DICATORPASSTHRU
INDICATORCOMPLEMENT
AUTORESUME
CLOCKSUSPENDM
CARKITMODE
1
0
FSLSSERIALMODE_6PIN
6
FSLSSERIALMODE_3PIN
7
INTERFACE_PROTECT_DISABLE
WRITE LATENCY
BITS
FIELD NAME
TYPE
RESET
7
INTERFACE_PROTECT_DISABLE
DESCRIPTION
RW
0
6
INDICATORPASSTHRU
RW
0
5
INDICATORCOMPLEMENT
RW
0
4
AUTORESUME
RW
1
3
CLOCKSUSPENDM
RW
0
2
CARKITMODE
RW
0
1
FSLSSERIALMODE_3PIN
RW
0
0
FSLSSERIALMODE_6PIN
R
0
9.1.11 OTG_CTRL
ADDRESS OFFSET
0x0A
PHYSICAL ADDRESS
0x0A
DESCRIPTION
Controls UTMI+ OTG functions of the PHY.
TYPE
RW
INSTANCE
USB_SCUSB
WRITE LATENCY
34
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
BITS
7
7
6
5
4
3
2
1
0
DRVVBUSEXTERNAL
DRVVBUS
CHRGVBUS
DISCHRGVBUS
DMPULLDOWN
DPPULLDOWN
IDPULLUP
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
USEEXTERNALVBUSINDICATOR
www.ti.com
FIELD NAME
DESCRIPTION
USEEXTERNALVBUSINDICA Tells the PHY to use an external VBUS over-current indicator.
TOR
TYPE
RESET
RW
0
RW
0
RW
0
RW
0
RW
0
RW
1
RW
1
RW
0
0b: Use the internal OTG comparator (VA_VBUS_VLD) or internal
VBUS valid indicator (default)
1b: Use external VBUS valid indicator signal.
6
DRVVBUSEXTERNAL
Selects between the internal and the external 5 V VBUS supply.
0b: Pin17 (CPEN) is disabled (output GND level). TUSB1210 does
not support internal VBUS supply.
1b: Pin17 (CPEN) is set to ‘1’ (output VDD33 voltage level) if
DRVVBUS bit is ‘1’, else Pin17 (CPEN) is disabled (output GND
level) if DRVVBUS bit is ‘0’
5
DRVVBUS
VBUS output control bit
0b : do not drive VBUS
1b : drive 5V on VBUS
Note: Both DRVVBUS and DRVVBUSEXTERNAL bits must be set
to 1 in order to to set Pin17 (CPEN). CPEN pin can be used to
enable an external VBUS supply
4
CHRGVBUS
Charge VBUS through a resistor. Used for VBUS pulsing SRP. The
Link must first check that VBUS has been discharged (see
DischrgVbus register bit), and that both D+ and D- data lines have
been low (SE0) for 2ms.
0b : do not charge VBUS
1b : charge VBUS
3
DISCHRGVBUS
Discharge VBUS through a resistor. If the Link sets this bit to 1, it
waits for an RX CMD indicating SessEnd has transitioned from 0 to
1, and then resets this bit to 0 to stop the discharge.
0b : do not discharge VBUS
1b : discharge VBUS
2
DMPULLDOWN
Enables the 15k Ohm pull-down resistor on D-.
0b : Pull-down resistor not connected to D-.
1b : Pull-down resistor connected to D-.
1
DPPULLDOWN
Enables the 15k Ohm pull-down resistor on D+.
0b : Pull-down resistor not connected to D+.
1b : Pull-down resistor connected to D+.
0
IDPULLUP
Connects a pull-up to the ID line and enables sampling of the signal
level.
0b : Disable sampling of ID line.
1b : Enable sampling of ID line.
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
35
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
9.1.12 OTG_CTRL_SET
ADDRESS OFFSET
0x0B
PHYSICAL ADDRESS
0x0B
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the otg_ctrl register with read/set-only property (write '1' to set
a particular bit, a write '0' has no-action).
TYPE
RW
7
6
5
4
3
2
1
0
USEEXTERNALVBUSINDICATOR
DRVVBUSEXTERNAL
DRVVBUS
CHRGVBUS
DISCHRGVBUS
DMPULLDOWN
DPPULLDOWN
IDPULLUP
WRITE LATENCY
BITS
FIELD NAME
TYPE
RESET
7
USEEXTERNALVBUSINDICATOR
DESCRIPTION
RW
0
6
DRVVBUSEXTERNAL
RW
0
5
DRVVBUS
RW
0
4
CHRGVBUS
RW
0
3
DISCHRGVBUS
RW
0
2
DMPULLDOWN
RW
1
1
DPPULLDOWN
RW
1
0
IDPULLUP
RW
0
9.1.13 OTG_CTRL_CLR
ADDRESS OFFSET
0x0C
PHYSICAL ADDRESS
0x0C
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the otg_ctrl register with read/Clear-only property (write '1' to
clear a particular bit, a write '0' has no-action).
TYPE
RW
WRITE LATENCY
36
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
5
4
3
2
DRVVBUS
CHRGVBUS
DISCHRGVBUS
DMPULLDOWN
1
0
IDPULLUP
6
DPPULLDOWN
7
DRVVBUSEXTERNAL
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
USEEXTERNALVBUSINDICATOR
www.ti.com
BITS
FIELD NAME
TYPE
RESET
7
USEEXTERNALVBUSINDICATOR
DESCRIPTION
RW
0
6
DRVVBUSEXTERNAL
RW
0
5
DRVVBUS
RW
0
4
CHRGVBUS
RW
0
3
DISCHRGVBUS
RW
0
2
DMPULLDOWN
RW
1
1
DPPULLDOWN
RW
1
0
IDPULLUP
RW
0
9.1.14 USB_INT_EN_RISE
ADDRESS OFFSET
0x0D
PHYSICAL ADDRESS
0x0D
DESCRIPTION
If set, the bits in this register cause an interrupt event notification to be
generated when the corresponding PHY signal changes from low to high. By
default, all transitions are enabled.
TYPE
RW
INSTANCE
USB_SCUSB
Reserved
Reserved
IDGND_RISE
3
2
1
0
HOSTDISCONNECT_RISE
4
VBUSVALID_RISE
5
SESSVALID_RISE
6
SESSEND_RISE
7
Reserved
WRITE LATENCY
BITS
FIELD NAME
TYPE
RESET
7
Reserved
DESCRIPTION
R
0
6
Reserved
R
0
5
Reserved
R
0
4
IDGND_RISE
RW
1
RW
1
Generate an interrupt event notification when IdGnd changes from
low to high.
Event is automatically masked if IdPullup bit is clear to 0 and for
50ms after IdPullup is set to 1.
3
SESSEND_RISE
Generate an interrupt event notification when SessEnd changes
from low to high.
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
37
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
BITS
FIELD NAME
DESCRIPTION
TYPE
RESET
2
SESSVALID_RISE
Generate an interrupt event notification when SessValid changes
from low to high. SessValid is the same as UTMI+ AValid.
RW
1
1
VBUSVALID_RISE
Generate an interrupt event notification when VbusValid changes
from low to high.
RW
1
0
HOSTDISCONNECT_RISE
Generate an interrupt event notification when Hostdisconnect
changes from low to high. Applicable only in host mode
(DpPulldown and DmPulldown both set to 1b).
RW
1
9.1.15 USB_INT_EN_RISE_SET
ADDRESS OFFSET
0x0E
PHYSICAL ADDRESS
0x0E
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the usb_int_en_rise register with read/set-only property (write
'1' to set a particular bit, a write '0' has no-action).
TYPE
RW
BITS
FIELD NAME
7
6
5
7
6
5
4
3
2
1
0
Reserved
Reserved
Reserved
IDGND_RISE
SESSEND_RISE
SESSVALID_RISE
VBUSVALID_RISE
HOSTDISCONNECT_RISE
WRITE LATENCY
DESCRIPTION
TYPE
RESET
Reserved
R
0
Reserved
R
0
Reserved
R
0
4
IDGND_RISE
RW
1
3
SESSEND_RISE
RW
1
2
SESSVALID_RISE
RW
1
1
VBUSVALID_RISE
RW
1
0
HOSTDISCONNECT_RIS
E
RW
1
9.1.16 USB_INT_EN_RISE_CLR
ADDRESS OFFSET
0x0F
PHYSICAL ADDRESS
0x0F
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the usb_int_en_rise register with read/clear-only property
(write '1' to clear a particular bit, a write '0' has no-action).
TYPE
RW
WRITE LATENCY
38
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
7
6
5
4
3
2
1
0
Reserved
Reserved
IDGND_RISE
SESSEN D_RISE
SESSVALID_RISE
VBUSVALID_RISE
HOSTDISCONNECT_RISE
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Reserved
www.ti.com
BITS
FIELD NAME
TYPE
RESET
7
Reserved
DESCRIPTION
R
0
6
Reserved
R
0
5
Reserved
R
0
4
IDGND_RISE
RW
1
3
SESSEND_RISE
RW
1
2
SESSVALID_RISE
RW
1
1
VBUSVALID_RISE
RW
1
0
HOSTDISCONNECT_RISE
RW
1
9.1.17 USB_INT_EN_FALL
ADDRESS OFFSET
0x10
PHYSICAL ADDRESS
0x10
DESCRIPTION
If set, the bits in this register cause an interrupt event notification to be
generated when the corresponding PHY signal changes from low to high. By
default, all transitions are enabled.
TYPE
RW
INSTANCE
USB_SCUSB
BITS
FIELD NAME
7
6
5
4
3
2
1
0
Reserved
Reserved
Reserved
IDGND_FALL
SESSEND_FALL
SESSVALID_FALL
VBUSVALID_FALL
HOSTDISCONNECT_FALL
WRITE LATENCY
TYPE
RESET
7
Reserved
DESCRIPTION
R
0
6
Reserved
R
0
5
Reserved
R
0
4
IDGND_FALL
RW
1
Generate an interrupt event notification when IdGnd changes
from high to low.
Event is automatically masked if IdPullup bit is clear to 0 and for
50ms after IdPullup is set to 1.
3
SESSEND_FALL
Generate an interrupt event notification when SessEnd changes
from high to low.
RW
1
2
SESSVALID_FALL
Generate an interrupt event notification when SessValid changes
from high to low. SessValid is the same as UTMI+ AValid.
RW
1
1
VBUSVALID_FALL
Generate an interrupt event notification when VbusValid changes
from high to low.
RW
1
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
39
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
BITS
www.ti.com
FIELD NAME
0
HOSTDISCONNECT_FALL
DESCRIPTION
Generate an interrupt event notification when Hostdisconnect
changes from high to low. Applicable only in host mode
(DpPulldown and DmPulldown both set to 1b).
TYPE
RESET
RW
1
9.1.18 USB_INT_EN_FALL_SET
ADDRESS OFFSET
0x11
PHYSICAL ADDRESS
0x11
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the usb_int_en_fall register with read/set-only property (write
'1' to set a particular bit, a write '0' has no-action)
TYPE
RW
BITS
FIELD NAME
7
6
5
4
3
Reserved
Reserved
IDGND_FALL
SESSEND_FALL
2
1
0
HOSTDISCONNECT_FALL
5
VBUSVALID_FALL
6
SESSVALID_FALL
7
Reserved
WRITE LATENCY
DESCRIPTION
TYPE
RESET
Reserved
R
0
Reserved
R
0
Reserved
R
0
4
IDGND_FALL
RW
1
3
SESSEND_FALL
RW
1
2
SESSVALID_FALL
RW
1
1
VBUSVALID_FALL
RW
1
0
HOSTDISCONNECT_FALL
RW
1
9.1.19 USB_INT_EN_FALL_CLR
ADDRESS OFFSET
0x12
PHYSICAL ADDRESS
0x12
DESCRIPTION
This register doesn't physically exist.
INSTANC
E
USB_SCUSB
It is the same as the usb_int_en_fall register with read/clear-only property
(write '1' to clear a particular bit, a write '0' has no-action).
TYPE
RW
WRITE LATENCY
40
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
BITS
4
3
Reserved
IDGND_FALL
SESSEND_FALL
FIELD NAME
2
1
0
HOSTDISCONNECT_FALL
5
VBUSVALID_FALL
6
SESSVALID_FALL
7
Reserved
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Reserved
www.ti.com
TYPE
RESET
7
Reserved
DESCRIPTION
R
0
6
Reserved
R
0
5
Reserved
R
0
4
IDGND_FALL
RW
1
3
SESSEN D_FALL
RW
1
2
SESSVALID_FALL
RW
1
1
VBUSVALID_FALL
RW
1
0
HOSTDISCONNECT_FALL
RW
1
9.1.20 USB_INT_STS
ADDRESS OFFSET
0x13
PHYSICAL ADDRESS
0x13
DESCRIPTION
Indicates the current value of the interrupt source signal.
TYPE
R
INSTANCE
USB_SCUSB
6
5
4
3
2
1
0
Reserved
IDGND
SESSEND
SESSVALID
VBUSVALID
HOSTDISCONNECT
Reserved
7
Reserved
WRITE LATENCY
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
41
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
BITS
www.ti.com
TYPE
RESET
7
Reserved
FIELD NAME
DESCRIPTION
R
0
6
Reserved
R
0
5
Reserved
R
0
4
IDGND
R
0
Current value of UTMI+ IdGnd output.
This bit is not updated if IdPullup bit is reset to 0 and for 50 ms after IdPullup is set to
1.
3
SESSEND
Current value of UTMI+ SessEnd output.
R
0
2
SESSVALID
Current value of UTMI+ SessValid output. SessValid is the same as UTMI+ AValid.
R
0
1
VBUSVALID
Current value of UTMI+ VbusValid output.
R
0
0
HOSTDISCONNECT Current value of UTMI+ Hostdisconnect output.
R
0
Applicable only in host mode.
Automatically reset to 0 when Low Power Mode is entered.
NOTE: Reset value is '0' when host is connected.
Reset value is '1' when host is disconnected.
9.1.21 USB_INT_LATCH
ADDRESS OFFSET
0x14
PHYSICAL ADDRESS
0x14
DESCRIPTION
These bits are set by the PHY when an unmasked change occurs on the
corresponding internal signal. The PHY will automatically clear all bits when
the Link reads this register, or when Low Power Mode is entered. The PHY
also clears this register when Serial Mode or Carkit Mode is entered regardless
of the value of ClockSuspendM.
INSTANC
E
USB_SCUSB
The PHY follows the rules defined in Table 26 of the ULPI spec for setting any
latch register bit. It is important to note that if register read data is returned to
the Link in the same cycle that a USB Interrupt Latch bit is to be set, the
interrupt condition is given immediately in the register read data and the Latch
bit is not set.
Note that it is optional for the Link to read the USB Interrupt Latch register in
Synchronous Mode because the RX CMD byte already indicates the interrupt
source directly
TYPE
R
BITS
42
FIELD NAME
Reserved
Reserved
IDGND_LATCH
3
2
1
0
HOSTDISCONNECT_LATCH
4
VBUSVALID_LATCH
5
SESSVALID_LATCH
6
SESSEND_LATCH
7
Reserved
WRITE LATENCY
DESCRIPTION
TYPE
RESET
7
Reserved
R
0
6
Reserved
R
0
5
Reserved
R
0
4
IDGND_LATCH
R
0
Set to 1 by the PHY when an unmasked event occurs on IdGnd. Cleared
when this register is read.
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
BITS
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
TYPE
RESET
3
SESSEND_LATCH
FIELD NAME
Set to 1 by the PHY when an unmasked event occurs on SessEnd.
Cleared when this register is read.
DESCRIPTION
R
0
2
SESSVALID_LATCH
Set to 1 by the PHY when an unmasked event occurs on SessValid.
Cleared when this register is read. SessValid is the same as UTMI+
AValid.
R
0
1
VBUSVALID_LATCH
Set to 1 by the PHY when an unmasked event occurs on VbusValid.
Cleared when this register is read.
R
0
0
HOSTDISCONNECT_LAT
CH
Set to 1 by the PHY when an unmasked event occurs on
Hostdisconnect. Cleared when this register is read. Applicable only in
host mode.
R
0
NOTE: As this IT is enabled by default, the reset value depends on the
host status
Reset value is '0' when host is connected.
Reset value is '1' when host is disconnected.
9.1.22 DEBUG
ADDRESS OFFSET
0x15
PHYSICAL ADDRESS
0x15
DESCRIPTION
Indicates the current value of various signals useful for debugging.
TYPE
R
INSTANCE
USB_SCUSB
BITS
6
5
4
3
2
Reserved
Reserved
Reserved
Reserved
Reserved
0
TYPE
RESET
7
Reserved
R
0
6
Reserved
R
0
5
Reserved
R
0
4
Reserved
R
0
3
Reserved
R
0
2
Reserved
R
0
R
0x0
1:00
FIELD NAME
1
LINESTATE
7
Reserved
WRITE LATENCY
LINESTATE
DESCRIPTION
These signals reflect the current state of the single ended receivers. They directly
reflect the current state of the DP (LineState[0]) and DM (LineState[1]) signals.
Read 0x0:
SE0 (LS/FS), Squelch (HS/Chirp)
Read 0x1:
LS: 'K' State,
FS: 'J' State,
HS: !Squelch,
Chirp: !Squelch & HS_Differential_Receiver_Output
Read 0x2:
LS: 'J' State,
FS: 'K' State,
HS: Invalid,
Chirp: !Squelch & !HS_Differential_Receiver_Output
Read 0x3:
SE1 (LS/FS), Invalid (HS/Chirp)
9.1.23 SCRATCH_REG
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
43
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
ADDRESS OFFSET
0x16
PHYSICAL ADDRESS
0x16
DESCRIPTION
Empty register byte for testing purposes. Software can read, write, set, and
clear this register and the PHY functionality will not be affected.
TYPE
RW
INSTANCE
USB_SCUSB
WRITE LATENCY
7
6
5
4
3
2
1
0
SCRATCH
BITS
FIELD NAME
DESCRIPTION
TYPE
RESET
7:00
SCRATCH
Scratch data.
RW
0x00
9.1.24 SCRATCH_REG_SET
ADDRESS OFFSET
0x17
PHYSICAL ADDRESS
0x17
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the scratch_reg register with read/set-only property (write '1'
to set a particular bit, a write '0' has no-action).
TYPE
RW
WRITE LATENCY
7
6
5
4
3
2
1
0
SCRATCH
BITS
7:00
FIELD NAME
DESCRIPTION
SCRATCH
TYPE
RESET
RW
0x00
9.1.25 SCRATCH_REG_CLR
ADDRESS OFFSET
0x18
PHYSICAL ADDRESS
0x18
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the scratch_reg with read/clear-only property (write '1' to clear
a particular bit, a write '0' has no-action).
TYPE
RW
WRITE LATENCY
7
6
5
4
3
2
1
0
SCRATCH
BITS
7:00
44
FIELD NAME
DESCRIPTION
SCRATCH
Register Map
TYPE
RESET
RW
0x00
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9.1.26 VENDOR_SPECIFIC1
ADDRESS OFFSET
0x3D
PHYSICAL ADDRESS
0x3D
DESCRIPTION
Power Control register .
TYPE
RW
INSTANCE
USB_SCUSB
BITS
FIELD NAME
2
1
0
ABNORMALSTRESS_EN
ID_FLOAT_EN
3
SPARE
MNTR_VUSBIN_OK_EN
4
BVALID_RISE
5
BVALID_FALL
6
ID_RES_EN
7
SPARE
WRITE LATENCY
TYPE
RESET
RW
0
MNTR_VUSBIN_OK_EN When set to 1, it enables RX CMDs for high to low or low to high
transitions on MNTR_VUSBIN_OK. This bit is provided for debugging
purposes.
RW
0
5
ID_FLOAT_EN
When set to 1, it enables RX CMDs for high to low or low to high
transitions on ID_FLOAT. This bit is provided for debugging purposes.
RW
0
4
ID_RES_EN
When set to 1, it enables RX CMDs for high to low or low to high
transitions on ID_RESA, ID_RESB and ID_RESC. This bit is provided for
debugging purposes.
RW
0
3
BVALID_FALL
Enables RX CMDs for high to low transitions on BVALID. When BVALID
changes from high to low, the USB TRANS will send an RX CMD to the
link with the alt_int bit set to 1b.
RW
0
RW
0
7
SPARE
6
DESCRIPTION
Reserved. The link must never write a 1b to this bit.
This bit is optional and is not necessary for OTG devices. This bit is
provided for debugging purposes. Disabled by default.
2
BVALID_RISE
Enables RX CMDs for low to high transitions on BVALID. When BVALID
changes from low to high, the USB Trans will send an RX CMD to the link
with the alt_int bit set to 1b.
This bit is optional and is not necessary for OTG devices. This bit is
provided for debugging purposes. Disabled by default.
1
SPARE
Reserved. The link must never write a 1b to this bit.
RW
0
0
ABNORMALSTRESS_E
N
When set to 1, it enables RX CMDs for low to high and high to low
transitions on ABNORMALSTRESS. This bit is provided for debugging
purposes.
RW
0
9.1.27 VENDOR_SPECIFIC1_SET
ADDRESS OFFSET
0x3E
PHYSICAL ADDRESS
0x3E
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the func_ctrl register with read/set-only property (write '1' to
set a particular bit, a write '0' has no-action).
TYPE
RW
WRITE LATEN CY
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
45
TUSB1210
BITS
4
3
ID_FLOAT_EN
ID_RES_EN
BVALID_FALL
FIELD NAME
2
1
0
ABNORMALSTRESS_EN
5
SPARE
6
BVALID_RISE
7
MNTR_VUSBIN_OK_EN
www.ti.com
SPARE
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
TYPE
RESET
7
SPARE
DESCRIPTION
RW
0
6
MNTR_VUSBIN_OK_EN
RW
0
5
ID_FLOAT_EN
RW
0
4
ID_RES_EN
RW
0
3
BVALID_FALL
RW
0
2
BVALID_RISE
RW
0
1
SPARE
RW
0
0
ABNORMALSTRESS_EN
RW
0
9.1.28 VENDOR_SPECIFIC1_CLR
ADDRESS OFFSET
0x3F
PHYSICAL ADDRESS
0x3F
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the func_ctrl register with read/clear-only property (write '1' to
clear a particular bit, a write '0' has no-action).
TYPE
RW
BITS
46
FIELD NAME
4
3
MNTR_VUSBIN_OK_EN
ID_FLOAT_EN
ID_RES_EN
BVALID_FALL
2
1
0
ABNORMALSTRESS_EN
5
SPARE
6
BVALID_RISE
7
SPARE
WRITE LATENCY
TYPE
RESET
7
SPARE
DESCRIPTION
RW
0
6
MNTR_VUSBIN_OK_EN
RW
0
5
ID_FLOAT_EN
RW
0
4
ID_RES_EN
RW
0
3
BVALID_FALL
RW
0
2
BVALID_RISE
RW
0
1
SPARE
RW
0
0
ABNORMALSTRESS_EN
RW
0
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9.1.29 VENDOR_SPECIFIC2
ADDRESS OFFSET
0x80
PHYSICAL ADDRESS
0x80
DESCRIPTION
Eye diagram programmability and DP/DM swap control .
TYPE
RW
INSTANCE
USB_SCUSB
BITS
FIELD NAME
7
SPARE
6
DATAPOLARITY
5:04
ZHSDRV
6
DATAPOLARITY
5
4
3
ZHSDRV
7
SPARE
WRITE LATENCY
2
1
0
IHSTX
DESCRIPTION
Control data polarity on dp/dm
High speed output impedance configuration for eye diagram tuning :
TYPE
RESET
RW
0
RW
1
RW
0x0
RW
0x1
00 45.455 Ω
01 43.779 Ω
10 42.793 Ω
11 42.411 Ω
3:00
IHSTX
High speed output drive strength configuration for eye diagram tuning :
0000 17.928 mA
0001 18.117 mA
0010 18.306 mA
0011 18.495 mA
0100 18.683 mA
0101 18.872 mA
0110 19.061 mA
0111 19.249 mA
1000 19.438 mA
1001 19.627 mA
1010 19.816 mA
1011 20.004 mA
1100 20.193 mA
1101 20.382 mA
1110 20.570 mA
1111 20.759 mA
IHSTX[0] is also the AC BOOST enable
IHSTX[0] = 0 à AC BOOST is disabled
IHSTX[0] = 1 à AC BOOST is enabled
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
47
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
9.1.30 VENDOR_SPECIFIC2_SET
ADDRESS OFFSET
0x81
PHYSICAL ADDRESS
0x81
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the VENDOR_SPECIFIC1 register with read/set-only property
(write '1' to set a particular bit, a write '0' has no-action).
TYPE
RW
6
DATAPOLARITY
5
4
3
ZHSDRV
7
SPARE
WRITE LATENCY
2
1
0
IHSTX
BITS
FIELD NAME
TYPE
RESET
7
SPARE
DESCRIPTION
RW
0
6
DATAPOLARITY
RW
1
5:04
ZHSDRV
RW
0x0
3:00
IHSTX
RW
0x1
9.1.31 VENDOR_SPECIFIC2_CLR
ADDRESS OFFSET
0x82
PHYSICAL ADDRESS
0x82
DESCRIPTION
This register doesn't physically exist.
INSTANCE
USB_SCUSB
It is the same as the VENDOR_SPECIFIC1 register with read/clear-only
property (write '1' to clear a particular bit, a write '0' has no-action).
TYPE
RW
BITS
48
FIELD NAME
6
DATAPOLARITY
5
4
ZHSDRV
7
SPARE
WRITE LATENCY
3
2
1
0
IHSTX
DESCRIPTION
TYPE
RESET
0
7
SPARE
RW
6
DATAPOLARITY
RW
1
5:04
ZHSDRV
RW
0x0
3:00
IHSTX
RW
0x1
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
9.1.32 VENDOR_SPECIFIC1_STS
ADDRESS OFFSET
0x83
PHYSICAL ADDRESS
0x83
DESCRIPTION
Indicates the current value of the interrupt source signal.
TYPE
R
INSTANCE
USB_SCUSB
BITS
FIELD NAME
7
Reserved
6
MNTR_VUSBIN_OK_STS
5
4
4
3
MNTR_VUSBIN_OK_STS
ABNORMALSTRESS_STS
ID_FLOAT_STS
ID_RESC_STS
2
1
0
BVALID_STS
5
ID_RESA_STS
6
ID_RESB_STS
7
Reserved
WRITE LATEN CY
DESCRIPTION
TYPE
RESET
R
0
Current value of MNTR_VUSBIN_OK output
R
0
ABNORMALSTRESS_STS
Current value of ABNORMALSTRESS output
R
0
ID_FLOAT_STS
Current value of ID_FLOAT output
R
0
3
ID_RESC_STS
Current value of ID_RESC output
R
0
2
ID_RESB_STS
Current value of ID_RESB output
R
0
1
ID_RESA_STS
Current value of ID_RESA output
R
0
0
BVALID_STS
Current value of VB_SESS_VLD output
R
0
9.1.33 VENDOR_SPECIFIC1_LATCH
ADDRESS OFFSET
0x84
PHYSICAL ADDRESS
0x84
DESCRIPTION
These bits are set by the PHY when an unmasked change occurs on the
corresponding internal signal. The PHY will automatically clear all bits when
the Link reads this register, or when Low Power Mode is entered. The PHY
also clears this register when Serial mode is entered regardless of the value of
ClockSuspendM.
INSTANCE
USB_SCUSB
The PHY follows the rules defined in Table 26 of the ULPI spec for setting any
latch register bit.
TYPE
R
6
5
4
3
2
1
0
ABNORMALSTRESS_LATCH
ID_FLOAT_LATCH
ID_RESC_LATCH
ID_RESB_LATCH
ID_RESA_LATCH
BVALID_LATCH
Reserved
7
MNTR_VUSBIN_OK_LATCH
WRITE LATENCY
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
49
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
BITS
FIELD NAME
7
Reserved
6
MNTR_VUSBIN_OK_LATCH
5
www.ti.com
DESCRIPTION
TYPE
RESET
R
0
Set to 1 when an unmasked event occurs on MNTR_VUSBIN_OK_LATCH.
Clear on read register.
R
0
ABNORMALSTRESS_LATCH
Set to 1 when an unmasked event occurs on ABNORMALSTRESS. Clear on
read register.
R
0
4
ID_FLOAT_LATCH
Set to 1 when an unmasked event occurs on ID_FLOAT. Clear on read
register.
R
0
3
ID_RESC_LATCH
Set to 1 when an unmasked event occurs on ID_RESC. Clear on read
register.
R
0
2
ID_RESB_LATCH
Set to 1 when an unmasked event occurs on ID_RESB. Clear on read
register.
R
0
1
ID_RESA_LATCH
Set to 1 when an unmasked event occurs on ID_RESA. Clear on read
register.
R
0
0
BVALID_LATCH
Set to 1 when an unmasked event occurs on VB_SESS_VLD. Clear on read
register.
R
0
9.1.34 VENDOR_SPECIFIC3
ADDRESS OFFSET
0x85
PHYSICAL ADDRESS
0x85
INSTANCE
USB_SCUSB
DESCRIPTION
TYPE
RW
BITS
FIELD NAME
7
Reserved
6
SOF_EN
3
2
1
0
VUSB3V3_VSEL
4
IDGND_DRV
SOF_EN
5
CPEN_ODOS
6
CPEN_OD
7
RESERVED
WRITE LATENCY
DESCRIPTION
0: HS USB SOF detector disabled.
TYPE
RESET
RW
0
RW
0
RW
0
1: Enable HS USB SOF detection when PHY is set in device mode.
SOF are output on CPEN pin. HS USB SOF (start-of-frame) output
clock is available on CPEN pin when this bit is set. HS USB SOF
packet rate is 8 kHz.
This bit is provided for debugging purpose only. It must never been
write to ‘1’ in functional mode
5
CPEN_OD
This bit has no effect when CPEN_ODOS = ‘0’, else :
0: CPEN pad is in OS (Open Source) mode.
In this case CPEN pin has an internal NMOS driver, and will be active
LOW.
Externally there should be a pullup resistor on CPEN (min 1kohm) to a
supply voltage (max 3.6V).
1: CPEN pad is in OD (Open Drain) mode
In this case CPEN pin has an internal PMOS driver, and will be active
HIGH.
Externally there should be a pull-down resistor on CPEN (min 1 kΩ to
GND.
50
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
4
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
CPEN_ODOS
Mode selection bit for CPEN pin.
RW
0
0 : CPEN pad is in CMOS mode
1: CPEN pad is in OD (Open Drain) or OS (Open Source) mode
(controlled by CPEN_OD bit)
3
2:00
IDGND_DRV
Drives ID pin to ground
RW
0x0
VUSB3V3_VSEL
000 VRUSB3P1V = 2.5 V
RW
0x3
001 VRUSB3P1V = 2.75 V
010 VRUSB3P1V = 3.0 V
011 VRUSB3P1V = 3.10 V (default)
100 VRUSB3P1V = 3.20 V
101 VRUSB3P1V = 3.30 V
110 VRUSB3P1V = 3.40 V
111 VRUSB3P1V = 3.50 V
9.1.35 VENDOR_SPECIFIC3_SET
ADDRESS OFFSET
0x86
PHYSICAL ADDRESS
0x86
INSTANCE
USB_SCUSB
DESCRIPTION
TYPE
RW
6
5
4
3
SOF_EN
CPEN_OD
CPEN_ODOS
IDGND_DRV
2
1
0
VUSB3V3_VSEL
7
RESERVED
WRITE LATENCY
BITS
FIELD NAME
TYPE
RESET
7
Reserved
DESCRIPTION
RW
0
6
SOF_EN
RW
0
5
CPEN_OD
RW
0
4
CPEN _ODOS
RW
0
3
IDGND_DRV
RW
0x0
2:00
VUSB3V3_VSEL
RW
0x3
9.1.36 VENDOR_SPECIFIC3_CLR
ADDRESS OFFSET
0x87
PHYSICAL ADDRESS
0x87
INSTANCE
USB_SCUSB
DESCRIPTION
TYPE
RW
5
4
3
CPEN_ODOS
IDGND_DRV
2
1
0
VUSB3V3_VSEL
6
CPEN_OD
RESERVED
7
SOF_EN
WRITE LATENCY
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
51
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
52
www.ti.com
BITS
FIELD NAME
TYPE
RESET
7
Reserved
DESCRIPTION
RW
0
6
SOF_EN
RW
0
5
CPEN_OD
RW
0
4
CPEN_ODOS
RW
0
3
IDGND_DRV
RW
0x0
2:00
VUSB3V3_VSEL
RW
0x3
Register Map
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
10
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Application Information
10.1 Host or OTG, ULPI Input Clock Mode Application
Figure 10-1 shows a suggested application diagram for TUSB1210 in the case of ULPI input-clock mode
(60 MHz ULPI clock is provided by link processor), in Host or OTG application. Note this is just one
example, it is of course possible to operate as HOST or OTG while also in ULPI output-clock mode.
(See Note A)
14
CFG
11
CS
17
12
VBUS Switch
RESETB
CPEN
VDD15
CVDD15
EN
5V
IN
22
OUT
13
DATA6
10
DATA5
9
DATA4
7
DATA3
6
DATA2
5
DATA1
4
DATA0
3
VBUS
Supply
21
USB Receptacle
ESD
VBUS
VBAT
2
DIR
31
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
STP
NXT
DIR
1 (See Note B)
CLOCK
23
ID
26
VDDIO
32
VDD18
28, 30
DM
19
DM
N/C
DP
18
DP
N/C
SHIELD
N/C
GND
N/C
GND
B.
C.
D.
E.
NXT
CLOCK
VDD33
CVDD33
ID
A.
29
RESETB
(See Note C)
20
CVBUS
STP
REFCLK
CS_OUT
27 (See Note D)
DATA7
3.1–5.5 V
CBYP
Link Controller
TUSB1210
VDDIO Supply
N/C
VDDIO Supply
1.8-V Supply
25
CVDDIO
CVDD18
24
16
15
8
(See Note E)
Pin 11 (CS) : can be tied high to VIO if CS_OUT pin unavailable; Pin 14 (CFG) : tie-high is Don’t Care since ULPI
clock is used in input mode
Pin 1 (REFCLK) : must be tied low
Ext 3 V supply supported
Pin 27 (RESETB) can be tied to VDDIO if unused.
Pins labeled N/C (no-connect) are truly no-connect, and can be tied or left floating.
Figure 10-1. Host or OTG, ULPI Input Clock Mode Application Diagram
10.2 Device, ULPI Output Clock Mode Application
Figure 10-2 shows a suggested application diagram for TUSB1210 in the case of ULPI output clock mode
(60 MHz ULPI clock is provided by TUSB1210, while link processor or another external circuit provides
REFCLK), in Device mode application. Note this is just one example, it is of course possible to operate as
Device while also in ULPI input-clock mode. Refer also to Figure 10-1.
Application Information
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
53
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
14
(See Note A)
11
17
12
CFG
CS
CPEN
VDD15
22
3.1–5.5 V
21
VBUS
DATA6
10
DATA5
9
DATA4
7
DATA3
6
DATA2
5
DATA1
4
DATA0
3
VDD33
CVDD33
23
DIR
31
1
26
VDDIO
VDD18
28, 30
ID
19
DM
N/C
DP
18
DP
N/C
N/C
N/C
GND
GND
B.
C.
D.
E.
2
32
SHIELD
A.
NXT
DM
N/C
DATA6
DATA4
DATA3
29
CLOCK
DATA7
DATA5
STP
VBAT
(See Note C)
20
CVBUS
13
REFCLK
Supply
USB Receptacle
ESD
DATA7
VBUS
CS_OUT
RESETB
27 (See Note D)
RESETB
CVDD15
CBYP
Link Controller
TUSB1210
VDDIO Supply
DATA2
DATA1
DATA0
STP
NXT
(See Note B)
DIR
CLKIN
REFCLK
VDDIO Supply
1.8-V Supply
25
CVDDIO
CVDD18
24
16
15
8
(See Note E)
Pin 11 (CS) : can be tied high to VIO if CS_OUT pin unavailable; Pin 14 (CFG) : Tied to VDDIO for 26MHz REFCLK
mode here, tie to GND for 19.2MHz mode.
Pin 1 (REFCLK) : connect to external 3.3V square-wave reference clock
Ext 3 V supply supported
Pin 27 (RESETB) can be tied to VDDIO if unused.
Pins labeled N/C (no-connect) are truly no-connect, and can be tied or left floating.
Figure 10-2. Device, ULPI Output Clock Mode Application Diagram
54
Application Information
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
11
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
Glossary
CMOS
Complimentary Metal Oxide Semiconductor
DM
Data manual
DSP
Digital signal processor
ESD
Electrostatic discharge
ESR
Equivalent series resistance
hiZ
High-impedance
HS
High speed
HW
Hardware
IC
Integrated circuit
ID
Identification
IDDQ
Direct drain quiescent current
IF
Interface
IO or I/O
Input/output
JTAG
Joint test action group, ieee 1149.1 standard
LDO
Low dropout regulator
LS
Low speed
NA
Not applicable
OTG
On the go
PBGA
Plastic ball grid array
PCB
Printed circuit board
PD
Pulldown
PLL
Phase locked loop
POL
Polarity
PSRR
Power supply rejection ratio
PU
Pullup
RX
Receive
SW
Software
Glossary
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
55
TUSB1210
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
www.ti.com
SYNC/SYNCHRO Synchronization
56
SYS
System
TBD
To be defined
TRM
Technical reference manual
TX
Transmit
UART
Universal asynchronous receiver transmitter
ULPI
UTMI+ low pin interface
USB
Universal serial bus
UTMI
USB transceiver macrocell interface
Glossary
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
TUSB1210
www.ti.com
12
SLLSE09F – NOVEMBER 2009 – REVISED AUGUST 2012
TUSB1210 Package
12.1 TUSB1210 Standard Package Symbolization
TUSB1210BRHB
Pin 1 Indicator
YMLLLLS
$
Figure 12-1. Printed Device Reference
Table 12-1. TUSB1210 Nomenclature Description
FIELDS
MEANING
P
Marking used to note prototype (X), preproduction (P), or
qualified/production device (Blank)(1)
A
Mask set version descriptor (initial silicon = BLANK, first
silicon revision = A, second silicon revision = B,...) (2)
YM
Year month
LLLLS
Lot code
$
Fab Planning Code
12.2 Package Thermal Resistance Characteristics
Table 12-2 provides the thermal resistance characteristics for the recommended package type RHB (SPQFP-N32) used for the TUSB1210 device. Refer to the application report IC Package Thermal Metrics,
TI literature number SPRA953, further details concerning parameter definitions and usage.
Table 12-2. TUSB1210 Thermal Resistance Characteristics
PARAMETER
VALUE
UNIT
θJA
Junction-to-ambient thermal resistance
34.72
°C/W
EIA/JESD 51-1
θJC top
Junction-to-case top thermal resistance (1)
37.3
°C/W
No current JEDEC specification (2)
3.6
°C/W
No current JEDEC specification (2)
(3)
MEASUREMENT METHOD
θJC
bottom
Junction-to-case bottom thermal resistance
θJB
Junction-to-board thermal resistance or junctionto-pin thermal resistance
10.3
°C/W
EIA/ JESD 51-8.
ΨJT
Junction-to-top of package (not a true thermal
resistance)
0.5
°C/W
EIA/JESD 51-2
ΨJB
Junction-to-board (not a true thermal resistance)
10.5
°C/W
EIA/JESD 51-6
(1)
(2)
(3)
Top is surface of the package facing away from the PCB.
Refer to measurement method in Chapter 2 of IC Package Thermal Metrics, TI literature number SPRA953.
Bottom surface is the surface of the package facing towards the PCB.
TUSB1210 Package
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TUSB1210
57
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
TUSB1210BRHBR
ACTIVE
VQFN
RHB
32
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
T1210B
TUSB1210BRHBT
ACTIVE
VQFN
RHB
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
T1210B
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TUSB1210BRHBR
VQFN
RHB
32
3000
330.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
TUSB1210BRHBT
VQFN
RHB
32
250
180.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Jul-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TUSB1210BRHBR
VQFN
RHB
32
3000
367.0
367.0
35.0
TUSB1210BRHBT
VQFN
RHB
32
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated