AVAGO HFBR

HFBR-57E0LZ/ALZ/PZ/APZ
Multimode Small Form Factor Pluggable Transceivers
with LC connector for ATM, FDDI, Fast Ethernet and
SONET OC-3/SDH STM-1
Data Sheet
Description
Features
The HFBR-57E0 Small Form Factor Pluggable LC transceivers provide the system designer with a product to
implement a range of solutions for multimode fiber Fast
Ethernet and SONET OC-3 (SDH STM-1) physical layers for
ATM and other services.
x RoHS compliant
x Full compliance with ATM Forum UNI SONET OC-3
multimode fiber physical layer specification
x Full compliance with the optical performance requirements of the FDDI PMD Standard
x Full compliance with the optical performance requirements of 100Base-FX version of IEEE802.3u
x Industry standard Small Form Pluggable (SFP) package
x LC duplex connector optical interface
x Operates with 62.5/125 μm and 50/125 μm multimode
fiber
x Single +3.3 V power supply
x +3.3 V TTL LOS output
x Receiver outputs are squelch enabled
x Manufactured in an ISO 9001 certified facility
x Temperature range:
0 °C to +70° C
HFBR-57E0LZ/PZ:
-40 °C to +85 °C
HFBR-57E0ALZ/APZ:
x Bail de-latch option
This transceiver operates at a nominal wavelength of
1300 nm with an LC fiber connector interface with an
external connector shield (HFBR-57E0).
Transmitter Section
The transmitter section of the HFBR-57E0 utilizes a 1300
nm InGaAsP LED. This LED is packaged in the optical
subassembly portion of the transmitter section. It is
driven by a custom silicon IC which converts differential
PECL logic signals, ECL referenced (shifted) to a +3.3 V
supply, into an analog LED drive current.
Receiver Section
The receiver section of the HFBR-57E0 utilizes an InGaAs
PIN photodiode coupled to a custom silicon transimpedance preamplifier IC. It is packaged in the optical subassembly portion of the receiver.
This PIN/preamplifier combination is coupled to a custom
quantizer IC which provides the final pulse shaping for
the logic output and the Loss of Signal (LOS) function.
The data output is differential. The data output is PECL
compatible, ECL referenced (shifted) to a +3.3 V power
supply. This circuit also includes a loss of signal (LOS)
detection circuit which provides an open collector logic
high output in the absence of a usable input optical signal. The LOS output is +3.3 V TTL.
Applications
x OC-3 SFP transceivers are designed for ATM LAN and
WAN applications such as:
ATM switches and routers
SONET/SDH switch infrastructure
x Multimode fiber ATM backbone links
x Fast Ethernet
Loss of Signal
The Loss of Signal (LOS) output indicates that the optical
input signal to the receiver does not meet the minimum
detectablelevel for FDDI and OC-3 compliant signals.
When LOS is high it indicates loss of signal. When LOS is
low it indicates normal operation. The LOS thresholds are
set to indicate a definite optical fault has occurred (e.g.,
disconnected or broken fiber connection to receiver,
failed transmitter).
Module Package
The transceiver meets the Small Form Pluggable (SFP)
industry standard package utilizing an integral LC duplex
optical interface connector. The hot-pluggable capability of the SFP package allows the module to be installed
at any time – even with the host system operating and
on-line. This allows for system configuration changes or
maintenance without system down time. The HFBR-57E0
uses a reliable 1300 nm LED source and requires a 3.3 V
dc power supply for optimal design.
Module Diagrams
Figure 1 illustrates the major functional components of
the HFBR-57E0. The connection diagram of the module
is shown in Figure 2. Figures 5 and 7 depict the external
configuration and dimensions of the module.
Installation
The HFBR-57E0 can be installed in or removed from any
MultiSource Agreement (MSA) – compliant Small Form
Pluggable port regardless of whether the host equip-
20
V EE T
1
V EE T
19
TD-
2
NC**
18
TD+
3
Tx Disable
17
V EE T
4
MOD-DEF(2)
16
V CC T
5
MOD-DEF(1)
15
V CC R
6
MOD-DEF(0)
14
V EE R
7
NC
13
RD+
8
LOS
12
RD-
9
V EE R
11
V EE R
10
V EE R
TOP OF BOARD
BOTTOM OF BOARD
(AS VIEWED THROUGH TOP OF BOARD)
** Connect to Internal Ground.
Figure 2. Connection diagram of module printed circuit board.
ment is operating or not. The module is simply inserted,
electrical interface first, under finger pressure. Controlled
hot-plugging is ensured by design and by 3-stage pin sequencing at the electrical interface. The module housing
makes initial contact with the host board EMI shield mitigating potential damage due to Electro-Static Discharge
(ESD). The 3-stage pin contact sequencing involves (1)
Ground, (2) Power, and then (3) Signal pins, making contact with the host board surface mount connector in that
order. This printed circuit board card-edge connector is
depicted in Figure 2.
ELECTRICAL INTERFACE
OPTICAL INTERFACE
RECEIVER
RD+ (Receive Data)
Light from Fiber
Photodetector
Amplification &
Quantizattion
RD- (Receive Data)
Loss of Signal
TRANSMITTER
TD+ (Transmit Data)
Light to Fiber
LED
LED DRIVER
TD- (Transmit Data)
TX Disable
EEPROM
Figure 1. Transceiver functional diagram
2
MOD-DEF2
MOD-DEF1
MOD-DEF0
Serial Identification (EEPROM)
Electrostatic Discharge (ESD)
The HFBR-57E0 complies with the industry standard
MSA that defines the serial identification protocol. This
protocol uses the 2-wire serial CMOS E2PROM protocol
of the ATMEL AT24C01A or equivalent. The contents of
the HFBR-57E0 serial ID memory are defined in Table 3 as
specified in the SFP MSA.
There are two conditions in which immunity to ESD
damage is important. Table 1 documents our immunity
to both of these conditions. The first condition is during
handling of the transceiver prior to insertion into the
transceiver port. To protect the transceiver, it is important
to use normal ESD handling precautions.
Functional Data I/O
These precautions include using grounded wrist straps,
workbenches, and floor mats in ESD controlled areas.
The ESD sensitivity of the HFBR-57E0 is compatible with
typical industry production environments. The second
condition is static discharges to the exterior of the host
equipment chassis after installation. To the extent that the
duplex LC optical interface is exposed to the outside of
the host equipment chassis, it may be subject to systemlevel ESD requirements. The ESD performance of the
HFBR-57E0 exceeds typical industry standards.
The HFBR-57E0 fiberoptic transceiver is designed to accept industry standard differential signals. In order to reduce the number of passive components required on the
customer’s board, Avago has included the functionality
of the transmitter bias resistors and coupling capacitors
within the fiberoptic module. The transceiver is compatible with an “ac-coupled” configuration and is internally
terminated. Figure 5 depicts the functional diagram of
the HFBR-57E0.
Immunity
Regulatory Compliance
See Table 1 for transceiver Regulatory Compliance performance. The overall equipment design will determine the
certification level. The transceiver performance is offered
as a figure of merit to assist the designer.
Equipment hosting the HFBR-57E0 modules will be subjected to radio-frequency electro magnetic fields in some
environments. These transceivers have good immunity to
such fields due to their shielded design.
Table 1. Regulatory Compliance
Feature
Test Method
Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD-883C
Meets Class 2 (2000 to 3999 Volts).Withstand up to
2200 V applied between electrical pins.
Electrostatic Discharge (ESD)
to the Duplex LC Receptacle
Variation of IEC 61000-4-2
Typically withstand at least 25 kV without damage
when the LC connector receptacle is contacted by
a Human Body Model probe.
Electromagnetic Interference
(EMI)
FCC Class B
CENELEC CEN55022
Class B (CISPR 21)
VCCI Class 1
System margins are dependent on customer
board and chassis design.
Immunity
Variation of IEC 61000-4-3
Typically shows a negligible effect from a 10 V/m
field swept from 80 to 450 MHz applied to the
transceiver without a chassis enclosure.
Eye Safety
AEL Class 1
EN60825-1 (+A11)
Compliant per Avago testing under single fault
conditions.
TUV Certification: R 72042022
Component Recognition
Underwriters Laboratories and Canadian Standard Associations Joint
Component Recognition for Information Technology Equipment Including
Electrical Business Equipment
UL File#: E173874
RoHS Compliance
3
Reference to EU RoHS Directive 2002/95/EC
Electromagnetic Interference (EMI)
Ordering Information
Most equipment designs utilizing these high-speed transceivers from Avago will be required to meet the requirements of FCC in the United States, CENELEC EN55022
(CISPR 22) in Europe and VCCI in Japan.
The HFBR-57E0 1300 nm product is available for production orders through the Avago Component Field Sales
Offices and Authorized Distributors worldwide.
Eye Safety
These transceivers provide Class 1 eye safety by design.
Avago has tested the transceiver design for compliance
with the requirements listed in Table 1 under normal
operating conditions and under a single fault condition.
Flammability
The HFBR-57E0 transceiver housing is made of metal and
high strength, heat resistant, chemically resistant, and UL
94V-0 flame retardant plastic.
Shipping Container
For technical information regarding this product, please
visit the Avago website at www.avagotech.com.
Use the quick search feature to search for this part number. You may also contact the Avago Products Customer
Response Centre.
Applications Support Materials
Contact your local Avago Component Field Sales Office
for information on how to obtain PCB layouts and evaluation boards for the transceivers.
200
1.0
160
2.0
tr/f – TRANSMITTER
OUTPUT OPTICAL RISE/
FALL TIMES – ns
2.5
120
3.0
100
1260
1280
1300
1340
1320
1360
l C – TRANSMITTER OUTPUT OPTICAL RISE/FALL TIMES – ns
HFBR-57E0 TRANSMITTER TEST RESULTS
OF l C , Dl AND t r/f ARE CORRELATED AND COMPLY
WITH THE ALLOWED SPECTRAL WIDTH AS A FUNCTION
OF CENTER WAVELENGTH FOR VARIOUS RISE AND
FALL TIMES.
Transceiver Optical Power Budget versus Link Length
Figure 3. Transmitter Output Optical Spectral Width (FWHM) vs. Transmitter Output Optical Center Wavelength and Rise/Fall Times
6
5
RELATIVE INPUT OPTICAL POWER (dB)
Avago LED technology has produced 1300 nm LED
devices with lower aging characteristics than normally
associated with these technologies in the industry. The
industry convention is 1.5 db aging for 1300 nm LEDs. The
1300 nm Avago LEDs are specified to experience less than
1 db of aging over normal commercial equipment mission
life periods. Contact your Avago sales representative for
additional details.
1.5
140
The transceiver is packaged in a shipping container designed to protect it from mechanical and ESD damage
during shipment or storage.
Optical Power Budget (OPB) is the available optical power
for a fiberoptic link to accommodate fiber cable loses plus
losses due to in-line connectors, splices, optical switches,
and to provide margin for link aging and unplanned
losses due to cable plant reconfiguration or repair.
3.0
180
Dl - TRANSMITTER OUTPUT OPTICAL
SPECTRAL WIDTH (FWHM) - nm
The metal housing and shielded design of the HFBR-57E0
minimize the EMI challenge facing the host equipment
designer. These transceivers provide superior EMI performance. This greatly assists the designer in the management of the overall system EMI performance.
4
3
2
1
0
-3
-2
-1
0
1
2
3
EYE SAMPLING TIME POSITION (ns)
CONDITIONS:
1. T A = +25 C
2. V CC = 3.3 V dc
3. INPUT OPTICAL RISE/FALL TIMES = 1.0/2.1 ns.
4. INPUT OPTICAL POWER IS NORMALIZED TO
CENTER OF DATA SYMBOL.
5. NOTE 13 AND 14 APPLY.
Figure 4. Relative Input Optical Power vs. Eye Sampling Time Position
4
1 μH
3.3 V
10 μF
0.1 μF
1 μH
0.1 μF
3.3 V
Vc c T
HFBR-57E0
4.7 K to 10 K
Tx Dis
3.3 V
SO+
50 Ω
TD+
SO–
50 Ω
TD–
TX GND
0.1
μF
10 μF
SI+
50 Ω
RD+
SI–
50 Ω
RD–
Rx_LOS
RX GND
Rx_LOS
0.1 μF
130 Ω
0.1 μF
0.1 μF
82 Ω
MOD_DEF2
MOD_DEF1
MOD_DEF0
GPIO(X)
GPIO(X)
GP14
4.7 K to
10 K
4.7 K to
10 K
4.7 K to
10 K
3.3 V
Figure 5. Recommended application configuration
1 μH
V CC T
0.1 μF
1 μH
V CC R
3.3 V
0.1 μF
SFP MODULE
10 μF
0.1 μF
HOST BOARD
Note: Inductors must have less than 1 ohm series resistance per MSA.
Figure 6. MSA required power supply filter
5
10 μF
82 Ω
LED DRIVER
& SAFETY
CIRCUITRY
130 Ω
VccR
4.7 K to 10 K
SerDes
PROTOCOL
IC
82 Ω
0.1 μF
130 Ω
3.3 V
130 Ω
AMPLIFICATION
&
QUANTIZATION
82 Ω
EEPROM
Table 2. Pin Description
Pin
Name
Function/Description
MSA Notes
1
VEET
Transmitter Ground
2
NC
NC
3
Tx Disable
Transmitter Disable- Module disables on high or open
4
MOD-DEF2
Module Definition 2 - Two Wire Serial ID Interface
2
5
MOD-DEF1
Module Definition 1 - Two Wire Serial ID Interface
2
6
MOD-DEF0
Module Definition 0 - grounded in module
2
7
NC
NC
8
LOS
Loss of Signal - high indicates loss of signal
9
VEER
Receiver Ground
10
VEER
Receiver Ground
11
VEER
Receiver Ground
12
RD-
Inverse Received Data Out
4
13
RD+
Received Data Out
4
14
VEER
Receiver Ground
15
VCCR
Receiver Power -3.3 V ± 10%
5
16
VCCT
Transmitter Power -3.3 V ± 10%
5
1
3
17
VEET
Transmitter Ground
18
TD+
Transmitter Data In
6
19
TD-
Inverse Transmitter Data In
6
20
VEET
Transmitter Ground
Notes:
1.
Pin 2 connected to internal ground.
2.
Mod-Def 0, 1, 2. are the module definition pins. They should be pulled up with a 4.7 K - 10 K: resistor on the host board to a supply less than
VCCT +0.3 V or VCCR +0.3 V.
Mod-Def 0 is grounded by the module to indicate that the module is present.
Mod-Def 1 is clock line of two wire serial interface for optional serial ID.
Mod-Def 2 is data line of two wire serial interface for optional serial ID.
3.
LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 - 10 K:resistor on the host board to a
supply < VCCT, R +0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined
by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to <0.8 V.
4.
RD-/+: These are the differential receiver outputs. They are ac coupled 100 :differential lines which should be terminated with 100 : differential at the SERDES. The ac coupling is done inside the module and is thus not required on the host board. The voltage swing on these
lines will be between 400 and 2000 mV differential (200 - 1000 mV single ended) when properly terminated.
5.
VCCR and VCCT are the receiver and transmitter power supplies. They are defined as 2.97 - 3.63 V at the SFP connector pin. The maximum
supply current is 230 mA and the associated in-rush current will typically be no more than 30 mA above steady state after 500 nanoseconds.
6.
TD-/+: These are the differential transmitter inputs. They are ac coupled differential lines with 100 : differential termination inside the module.
The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 400 - 2000
mV (200 - 1000 mV single ended), though it is recommended that values between 400 and 1200 mV differential (200 - 600 mV single ended)
be used for best EMI performance. These levels are compatible with CML and LVPECL voltage swings.
6
Table 3. EEPROM Serial ID Memory Contents
Add
Hex
Add
Hex
Add
Hex
Add
Hex
0
03
33
20
63
Note 3
95
Note 3
1
04
34
20
64
00
96
Note 5
2
07
35
20
65
12
97
Note 5
3
00
36
00
66
00
98
Note 5
4
00
37
00
67
00
99
Note 5
5
01, Note 6
38
17
68
Note 1
100
Note 5
6
20, Note 6
39
6A
69
Note 1
101
Note 5
7
00
40
48
H
70
Note 1
102
Note 5
8
00
41
46
F
71
Note 1
103
Note 5
9
00
42
42
B
72
Note 1
104
Note 5
10
00
43
52
R
73
Note 1
105
Note 5
11
03, Note 7
44
2D
-
74
Note 1
106
Note 5
12
02, Note 8
45
35
5
75
Note 1
107
Note 5
13
00
46
37
7
76
Note 1
108
Note 5
14
00
47
45
E
77
Note 1
109
Note 5
15
00
48
30
0
78
Note 1
110
Note 5
16
C8
49
41, Note 4
A
79
Note 1
111
Note 5
17
C8
50
50, Note 4
P
80
Note 1
112
Note 5
18
00
51
5A, Note 4
Z
81
Note 1
113
Note 5
19
00
52
20, Note 4
82
Note 1
114
Note 5
20
41
A
53
20, Note 4
83
Note 1
115
Note 5
21
56
V
54
20
84
Note 2
116
Note 5
22
41
A
55
20
85
Note 2
117
Note 5
23
47
G
56
30
0
86
Note 2
118
Note 5
24
4F
O
57
30
0
87
Note 2
119
Note 5
25
20
58
30
0
88
Note 2
120
Note 5
26
20
59
30
0
89
Note 2
121
Note 5
27
20
60
05
90
Note 2
122
Note 5
28
20
61
1E
91
Note 2
123
Note 5
29
20
62
00
92
00
124
Note 5
30
20
93
00
125
Note 5
31
20
94
00
32
20
1.
2.
3.
4.
5.
6.
7.
8.
7
ASCII
ASCII
ASCII
126
Note 5
127
Note 5
ASCII
Addresses 68 - 83 specify a unique identifier.
Addresses 84 - 91 specify the date code.
Addresses 63 and 95 are check sums. Address 63 is the check sum for bytes 0 - 62 and address 95 is the check sum for bytes 64 - 94.
Part number options LZ, PZ, ALZ, APZ, etc. Example: for “AP” option, hexes in addresses 49, 50, 51, 52 and 52 will be 41, 50, 5A, 20 and 20
respectively.
Addresses 96-127 are vendor specific data.
Addresses 5 and 6 specify compliance code. Address 5 with Hex 01 for OC-3 and address 6 with Hex 20 for Fast Ethernet.
Address 11 specifies encoding code. Hex 03 for OC-3 and Hex 02 for Fast Ethernet.
Address 12 specifies bit rate. Hex 02 for OC-3 and Hex 01 for Fast Ethernet.
AVAGO HFBR-57E0xxZ
YYWW
Country of Origin
Tcase Reference Point
13.8±0.1
[0.541±0.004]
DEVICE SHOWN WITH
DUST CAP AND BAIL
WIRE DELATCH
13.4±0.1
[0.528±0.004]
2.60
[0.10]
55.2±0.2
[2.17±0.01]
FRONT EDGE OF SFP
TRANSCEIVER CAGE
6.25±0.05
[0.246±0.002]
13.0±0.2
[0.512±0.008]
TX
0.7MAX. UNCOMPRESSED
[0.028]
8.5±0.1
[0.335±0.004]
RX
AREA
FOR
PROCESS
PLUG
DIMENSIONS ARE IN MILLIMETERS (INCHES)
6.6
[0.261]
13.50
[0.53]
14.8MAX. UNCOMPRESSED
[0.583]
Figure 7. Module Drawing
8
X
Y
34.5
10
3x
7.2
10x ∅ 1.05 ± 0.01
∅ 0.1 L X A S
16.25
MIN. PITCH
7.1
2.5
∅ 0.85 ± 0.05
1
PCB
EDGE
8.58
11.08
16.25
14.25
REF .
∅ 0.1 S X Y
2.5
B
A
1
3.68
5.68
20
PIN 1
2x 1.7
8.48
9.6
4.8
11
10
11.93
SEE DETAIL 1
2.0
11x
5
26.8
11x 2.0
9x 0.95 ± 0.05
∅ 0.1 L X A S
10
3x
3
2
41.3
42.3
5
3.2
0.9
10.53
10.93
0.8
TYP.
1. PADS AND VIAS ARE CHASSIS GROUND
2. THROUGH HOLES, PLATING OPTIONAL
3. HATCHED AREA DENOTES COMPONENT
AND TRACE KEEPOUT (EXCEPT
CHASSIS GROUND)
4. AREA DENOTES COMPONENT
KEEPOUT (TRACES ALLOWED)
4
2x 1.55 ± 0.05
∅ 0.1 L A S B S
11.93
11
10
DETAIL 1
Figure 8. SFP host board mechanical layout
9
LEGEND
20
PIN 1
9.6
20x 0.5 ± 0.03
0.06 L A S B S
2 ± 0.005 TYP.
0.06 L A S B S
DIMENSIONS ARE IN MILLIMETERS
3.5±0.3
[.14±.01]
1.7±0.9
[.07±.04]
41.73±0.5
[1.64±.02]
PCB
BEZEL
AREA
FOR
PROCESS
PLUG
15MAX
.59
Tcase REFERENCE POINT
CAGE
ASSEMBLY
15.25±0.1
[.60±0.004]
12.4REF
.49
9.8MAX
.39
1.15REF
.05
BELOW PCB
10REF
.39
TO PCB
16.25±0.1MIN PITCH
[.64±0.004]
0.4±0.1
[.02±0.004]
BELOW PCB
MSA-SPECIFIED BEZEL
DIMENSIONS ARE IN MILLIMETERS [INCHES].
Figure 9. SFP Assembly Drawing
10
10.4±0.1
[.41±0.004]
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each
parameter in isolation, all other parameters having values within the recommended operating conditions. It should
not be assumed that limiting values of more than one parameter can be applied to the product at the same time.
Exposure to the absolute maximum ratings for extended periods can adversely affect device reliability.
Parameter
Symbol
Minimum
Maximum
Units
Storage Temperature
TS
-40
Typical
+100
°C
Supply Voltage
VCC
-0.5
3.63
V
Data Input Voltage
VI
-0.5
VCC
V
Differential Input Voltage (p-p)
VD
2.4
V
Output Current
IO
50
mA
Maximum
Units
+70
+85
°C
°C
Notes
1
Recommended Operating Conditions
Parameter
Symbol
Minimum
Typical
Case Operating Temperature
HFBR-57E0LZ/PZ
HFBR-57E0ALZ/APZ
TC
TC
0
-40
Supply Voltage
VCC
2.97
3.3
3.63
V
Data Input: Transmitter Differential Input
Voltage (TD+/-)
VI
0.5
0.8
2.4
V
Data and Loss of Signal Output Load
RL
50
Notes
:
2
Transmitter Electrical Characteristics
HFBR-57E0LZ/PZ (TC = 0 ºC to +70 ºC, VCC = 2.97 V to 3.63 V)
HFBR-57E0ALZ/APZ (TC = -40 ºC to +85 ºC, VCC = 2.97 V to 3.63 V)
Parameter
Symbol
Typical
Maximum
Units
Notes
Supply Current
ICC
Minimum
165
210
mA
3
Power Dissipation
PDISS
0.55
0.80
W
5a
Transmitter Disable (TX Disable) High
VIH
2.0
3.5
V
Transmitter Disable (TX Disable) Low
VIL
0
0.8
V
Receiver Electrical Characteristics
HFBR-57E0LZ/PZ (TC = 0 ºC to +70 ºC, VCC = 2.97 V to 3.63 V)
HFBR-57E0ALZ/APZ (TC = -40 ºC to +85 ºC, VCC = 2.97 V to 3.63 V)
Parameter
Symbol
Typical
Maximum
Units
Notes
Supply Current
ICC
95
150
mA
4
Power Dissipation
PDISS
0.35
0.55
W
5b
Data Output: Receiver Differential Output
Voltage (RD+/-)
VO
0.4
2.0
V
6a6b
Data Output Rise Time
tr
0.35
2.2
ns
7
Data Output Fall Time
tf
0.35
2.2
ns
7
Loss of Signal Output Voltage - Low
LOSVOL
Loss of Signal Output Voltage - High
LOSVOH
Power Supply Noise Rejection
PSNR
11
Minimum
0.8
2.0
50
V
6a
V
6a
mV
Notes:
1.
This is the maximum voltage that can be applied across the Differential Transmitter Data Inputs to prevent damage to the input ESD protection circuit.
2.
The data outputs are terminated with 50: .
The Loss of Signal output is terminated with 50 : connected to a pull-up resistor of 4.7 K: tied to VCC.
3.
The power supply current needed to operate the transmitter is provided to differential ECL circuitry. This circuitry maintains a nearly constant
current flow from the power supply. Constant current operation helps to prevent unwanted electrical noise from being generated and conducted or emitted to neighboring circuitry.
4.
This is the receiver supply current measured in mA.
5a. The power dissipation of the transmitter is calculated as the sum of the products of supply voltage and current.
5b. The power dissipation of the receiver is calculated as the sum of the products of supply voltage and currents, minus the sum of the products
of the output voltages and currents.
6a. Differential Output Voltage is internally ac coupled. The Loss of Signal low and high voltages are measured with load condition as mentioned
in note 2.
6b. Data and Data-bar outputs are squelched at LOS assert level. When the received light drops below LOS assert point, it will force receiver data
and data-bar to go to steady PECL levels High and Low respectively.
7.
The data output rise and fall times are measured between 20% and 80% levels.
Transmitter Optical Characteristics
HFBR-57E0LZ/PZ(TC = 0 ºC to +70 ºC, VCC = 2.97 V to 3.63 V)
HFBR-57E0ALZ/APZ (TC = -40 ºC to +85 ºC, VCC = 2.97 V to 3.63 V)
Parameter
Symbol
Minimum
Typical
Maximum Units
Notes
Output Optical Power
BOL
62.5/125 μm, NA = 0.275 Fiber EOL
PO
-19
-20
-15.7
-14
dBm avg
8
Output Optical Power
50/125 μm, NA = 0.20 Fiber
PO
-22.5
-23.5
-14
dBm avg
8
-45
dBm
1380
nm
21, Figure 3
nm
9, 21, Figure 3
BOL
EOL
Transmitter Disable (High)
PO(off )
Center Wavelength
OC
Spectral Width - FWHM
Spectral Width - RMS
'O
Optical Rise Time
tr
0.6
1.2
3.0
ns
10, 21, Figure 3
Optical Fall Time
tf
0.6
2.0
3.0
ns
10, 21, Figure 3
Systematic Jitter Contributed by the Transmitter - OC-3
SJ
0.25
1.2
ns p-p
11a
Duty Cycle Distortion Contributed by the
Transmitter - FE
DCD
0.20
0.6
ns p-p
11b
Data Dependent Jitter Contributed by the
Transmitter - FE
DDJ
0.07
0.6
ns p-p
11c
Random Jitter Contributed by the Transmitter
OC-3
FE
RJ
0.10
0.10
0.52
0.69
ns
p-p
12a
12b
1270
1308
147
63
Notes:
8.
These optical power values are measured with the following conditions:
The Beginning of Life (BOL) to the End of Life (EOL) optical power degradation is typically 1.5 dB per the industry convention for long wavelength LEDs. The actual degradation observed in Avago’s 1300 nm LED products is < 1 dB, as specified in this data sheet. Over the specified
operating voltage and temperature ranges. With 25 MBd (12.5 MHz square-wave), input signal.
At the end of one meter of noted optical fiber with cladding modes removed. The average power value can be converted to a peak power
value by adding 3 dB. Higher output optical power transmitters are available on special request. Please consult with your local Avago sales
representative for further details.
9.
The relationship between Full Width Half Maximum and RMS values for Spectral Width is derived from the assumption of a Gaussian shaped
spectrum which results in a 2.35 X RMS = FWHM relationship.
10. The optical rise and fall times are measured from 10% to 90% when the transmitter is driven by a 25 MBd (12.5 MHz square-wave) input
signal. The ANSI T1E1.2 committee has designated the possibility of defining an eye pattern mask for the transmitter optical output as an item
for further study. Avago will incorporate this requirement into the specifications for these products if it is defined. The HFBR-57E0 products
typically comply with the template requirements of CCITT (now ITU-T) G.957 Section 3.2.5, Figure 2 for the STM- 1 rate, excluding the optical
receiver filter normally associated with single mode fiber measurements which is the likely source for the ANSI T1E1.2 committee to follow in
this matter.
12
Notes:
11a. Systematic Jitter contributed by the transmitter is defined as the combination of Duty Cycle Distortion and Data Dependent Jitter. Systematic
Jitter is measured at 50% threshold using a 155.52 MBd (77.5 MHz square-wave), 223- 1 psuedorandom data pattern input signal.
11b. Duty Cycle Distortion contributed by the transmitter is measured at the 50% threshold of the optical output signal using an IDLE Line State,
125 MBd (62.5 MHz square-wave), input signal.
11c. Data Dependent Jitter contributed by the transmitter is specified with the FDDI test pattern described in FDDI PMD Annex A.5.
12a. Random Jitter contributed by the transmitter is specified with a 155.52 MBd (77.5 MHz square-wave) input signal.
12b. Random Jitter contributed by the transmitter is specified with an IDLE Line State, 125 MBd (62.5 MHz square-wave) input signal. See Application Information - Transceiver Jitter Performance Section of this data sheet for further details.
Receiver Optical and Electrical Characteristics
HFBR-57E0LZ /PZ(TC = 0 ºC to +70 ºC, VCC = 2.97 V to 3.63 V)
HFBR-57E0ALZ/APZ (TC = -40 ºC to +85 ºC, VCC = 2.97 V to 3.63 V)
Parameter
Symbol
Input Optical Power minimum at Window Edge
OC-3
FE
PIN MIN (W)
Input Optical Power at Eye Center
OC-3
FE
PIN MIN (C)
Input Optical Power Maximum
OC-3
FE
PIN MAX
Minimum
Typical
Maximum
Units
Notes
-30
-31
dBm avg
13a,
Figure 4
13b
dBm avg
-31
-31.8
14a,
Figure 4
14b
dBm avg
13a
13b
-14
-14
Operating Wavelength
O
1380
nm
Systematic Jitter Contributed by the Receiver
OC-3
SJ
0.11
1.2
ns p-p
15a
Duty Cycle Distortion Contributed by the Receiver
FE
DCD
0.08
0.4
ns p-p
15b
Data Dependent Jitter Contributed by the Receiver
FE
DDJ
0.02
1.0
ns p-p
15c
Random Jitter Contributed by the Receiver
OC-3
FE
RJ
0.14
0.14
1.91
2.14
Loss of Signal - Deasserted
OC-3
FE
PA
PD +
1.5 dB
Loss of Signal - Asserted
PD
Loss of Signal - Hysteresis
PA - PD
1270
ns p-p
-31
-33
16a
16b
dBm avg
17
-45
dBm avg
18
1.5
dB
Loss of Signal Deassert Time (on to off )
0
2
100
μs
19
Loss of Signal Assert Time (off to on)
0
5
350
μs
20
Notes:
13a. This specification is intended to indicate the performance of the receiver section of the transceiver when Input Optical Power signal characteristics are present per the following definitions. The Input Optical Power dynamic range from the minimum level (with a window time-width) to
the maximum level is the range over which the receiver is guaranteed to provide output data with a Bit Error Rate (BER) better than or equal
to 1 x 10-10.
- At the Beginning of Life (BOL)
- Over the specified operating temperature and voltage ranges
- Input is a 155.52 MBd, 223-1 PRBS data pattern with 72 “1” s and 72 “0”s inserted per the CCITT (now ITU-T) recommendation G.958 Appendix
I.
- Receiver data window time-width is 1.23 ns or greater for the clock recovery circuit to operate in. The actual test data window time-width
is set to simulate the effect of worst case optical input jitter based on the transmitter jitter values from the specification tables. The test
window time-width is 3.32 ns.
- Transmitter operating with a 155.52 MBd, 77.5 MHz square-wave, input signal to simulate any cross-talk present between the transmitter
and receiver sections of the transceiver.
13
13b. This specification is intended to indicate the performance of the receiver section of the transceiver when Input Optical Power signal characteristics are
present per the following definitions. The Input Optical Power dynamic range from the minimum level (with a window time-width) to the maximum
level is the range over which the receiver is guaranteed to provide output data with a Bit Error Rate (BER) better than or equal to 2.5 x 10-10.
• At the Beginning of Life (BOL)
• Over the specified operating temperature and voltage ranges
• Input symbol pattern is the FDDI test pattern defined in FDDI PMD Annex A.5 with 4B/5B NRZI encoded data that contains a duty cycle base-line
wander effect of 50 kHz. This sequence causes a near worst case condition for inter-symbol interference.
• Receiver data window time-width is 2.13 ns or greater and centered at mid-symbol. This worst case window time-width is the minimum allowed
eye-opening presented to the FDDI PHY PM_Data indication input (PHY input) per the example in FDDI PMD Annex E. This minimum window
time-width of 2.13 ns is based upon the worst case FDDI PMD Active Input Interface optical conditions for peak-to-peak DCD (1.0 ns), DDJ (1.2 ns)
and RJ (0.76 ns) presented to the receiver.
To test a receiver with the worst case FDDI PMD Active Input jitter condition requires exacting control over DCD, DDJ and RJ jitter components that
is difficult to implement with production test equipment. The receiver can be equivalently tested to the worst case FDDI PMD input jitter conditions and meet the minimum output data window time-width of 2.13 ns. This is accomplished by using a nearly ideal input optical signal (no DCD,
insignificant DDJ and RJ) and measuring for a wider window time-width of 4.6 ns. This is possible due to the cumulative effect of jitter components
through their superposition (DCD and DDJ are directly additive and RJ components are rms additive). Specifically, when a nearly ideal input optical
test signal is used and the maximum receiver peak-to-peak jitter contributions of DCD (0.4 ns), DDJ (1.0 ns), and RJ (2.14 ns) exist, the minimum
window time-width becomes 8.0 ns -0.4 ns - 1.0 ns - 2.14 ns = 4.46 ns, or conservatively 4.6 ns. This wider window time-width of 4.6 ns guarantees
the FDDI PMD Annex E minimum window time-width of 2.13 ns under worst case input jitter conditions to the Avago receiver.
• Transmitter operating with an IDLE Line State pattern, 125 MBd (62.5 MHz square-wave), input signal to simulate any cross-talk present between
the transmitter and receiver sections of the transceiver.
14a. All conditions of Note 13a apply except that the measurement is made at the center of the symbol with no window time- width.
14b. All conditions of Note 13b apply except that the measurement is made at the center of the symbol with no window time-width.
15a. Systematic Jitter contributed by the receiver is defined as the combination of Duty Cycle Distortion and Data Dependent Jitter. Systematic Jitter is
measured at 50% threshold using a 155.52 MBd (77.5 MHz square- wave), 223-1 psuedorandom data pattern input signal.
15b Duty Cycle Distortion contributed by the receiver is measured at the 50% threshold of the electrical output signal using an IDLE Line State,
125 MBd (62.5 MHz square-wave), input signal. The input optical power level is -20 dBm average.
15c. Data Dependent Jitter contributed by the receiver is specified with the FDDI DDJ test pattern described in the FDDI PMD Annex A.5. The input
optical power level is -20 dBm average.
16a. Random Jitter contributed by the receiver is specified with a 155.52 MBd (77.5 MHz square- wave) input signal.
16b. Random Jitter contributed by the receiver is specified with an IDLE Line State, 125 MBd (62.5 MHz square-wave), input signal. The input optical
power level is at maximum “PIN MIN (W)”. See Application Information - Transceiver Jitter Section for further information.
17. This value is measured during the transition from low to high levels of input optical power.
18. This value is measured during the transition from high to low levels of input optical power. At Loss of Signal assert, the receiver outputs Data
Out and Data Out Bar go to steady PECL levels High and Low respectively.
19. The Loss of Signal output shall be de-asserted within 100 μs after a step increase of the Input Optical Power.
20. Loss of Signal output shall be asserted within 350 μs after a step decrease in the Input Optical Power. At Loss of Signal Assert, the receiver
outputs Data Out and Data Out Bar go to steady PECL levels High and Low respectively.
21. The HFBR-57E0 transceiver complies with the requirements for the trade-offs between center wavelength, spectral width, and rise/fall times
shown in Figure 3. This figure is derived from the FDDI PMD standard (ISO/IEC 9314-3 : 1990 and ANSI X3.166 - 1990) per the description in
ANSI T1E1.2 Revision 3. The interpretation of this figure is that values of Center Wavelength and Spectral Width must lie along the appropriate
Optical Rise/Fall Time curve.
14
Ordering Information
1300 nm LED (Operating Case Temperature 0 to +70 °C)
HFBR-57E0LZ
HFBR-57E0PZ
Standard de-latch
Bail de-latch
1300 nm LED (Operating Case Temperature -40 °C to +85 °C)
HFBR-57E0ALZ Standard de-latch
HFBR-57E0APZ Bail de-latch
EEPROM contents and/or label options
HFBR-57E0LZ-YYY
HFBR-57E0PZ-YYY
HFBR-57E0ALZ-YYY
HFBR-57E0APZ-YYY
Standard de-latch, 0 to +70°C
Bail de-latch, 0 to +70°C
Standard de-latch, -40°C to +85°C
Bail de-latch, -40°C to +85°C
Where “YYY” is customer specific.
Handling Precaution
The HFBR-57E0xxZ is a pluggable module and is NOT designed for aqueous wash, IR reflow or wave soldering processes.
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. Obsoletes AV01-0456EN
AV02-2810EN - Januaray 20, 2011