DAESAN RL1632W-4

1/2W, 0612 Low Resistance Chip Resistor (Lead / Halogen Free)
1. Scope
This specification applies to 1.6mm x 3.2mm size 1/2W, fixed metal film chip resistors rectangular
type for use in electronic equipment.
2. Type Designation
RL1632W - □ - □□□□
(1)
(2)
(3)
Where
(1) Series No.
□
(4)
(2) 4=1/2W
(3) Resistance value :
For example - R001 = 1mΩ
The “ R “ shall be used as a decimal point.
(4) Resistance value :
F = ± 1%
G = ± 2%
J = ± 5%
3. Outline Designation
(1) Substrate
(2) Resistor
(3) Terminals
(4) Marking
(5)Protection coat:
Alumina 96%
Cu-alloy
Sn (on Cu )
Heat resistive epoxy resin(White)
Heat resistive epoxy resin(Green)
Dimensions (mm)
Code Letter
RL1632W
L
1.6 ± 0.25
W
3.15 ± 0.25
a
0.35 ± 0.2
t
0.95 ± 0.25
Figure 1. Construction and Dimensions
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
=±
X.X
=±
X.XX = ±
ANGLES ± HOLE DIA. ±
DRAWN
BY ﹕ connie 4/3/13
DESIGNED BY ﹕
CHECKED
BY ﹕
APPROVED BY ﹕
SCALE ﹕ X
UNIT ﹕ X
Engineering Spec. For 1/2W 0612
TITLE : The
Low Resistance Chip Resistor
台達電子工業股份有限公司
Delta Electronics, Inc.
乾坤科技股份有限公司
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
NO.
SMN40000NH
PAGE 1
PAGE
REV.
A2
OF 6
4. Ratings
4-1 Specification
Power Ratings *
1/2 W
Resistance Value
1 ~10mΩ
±1% 、±2% 、±5%
Resistance Tolerance
RATED LOAD(%)
Temperature Coefficient of
±150ppm/℃ (Reflow)
Resistance
Note *:
Power ratings is based on continuous full load operation at rated ambient temperature of 70℃.
For resistors operated at ambient temperature in excess of 70℃, the maximum load shall be
derated in accordance with the following curve.
100
0
-55
70
155
AMBIENT TEMPERATURE(℃)
Figure 2.:Power Temperature Derating Curve
4-2 Rated Voltage
The rated voltage shall be determined by the following expression.
V = P× R
Where V:Rated voltage (V)
R:Nominal resistance value (Ω)
P:Rated dissipation (W)
4-3 Operating and Storage Temperature Range
-55 to +155℃
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
=±
X.X
=±
X.XX = ±
ANGLES ± HOLE DIA. ±
DRAWN
BY ﹕ connie 4/3/13
DESIGNED BY ﹕
CHECKED
BY ﹕
APPROVED BY ﹕
SCALE ﹕ X
UNIT ﹕ X
Engineering Spec. For 1/2W 0612
TITLE : The
Low Resistance Chip Resistor
台達電子工業股份有限公司
Delta Electronics, Inc.
乾坤科技股份有限公司
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
NO.
SMN40000NH
PAGE 2
PAGE
REV.
A2
OF 6
5. Life test
Test Item
Condition of Test
Requirements
Short Time Overload
2.5 * rated power for 5 seconds
Refer to JIS C 5201-1 4.13
∆R : ± 1.0%
Thermal Shock
-55 ~125℃ 100 cycles, 15 min at each
extreme condition
Refer to JIS C 5201-1 4.19
∆R : ± 1.0%
Low Temperature Storage
Kept at -55℃, 1,000 hours
Refer to JIS C 5201-1 4.23.4
∆R : ± 2.0%
Load Life
Rated voltage for 1.5hours followed by a
pause 0.5hour at 70 ± 3℃.
Cycle repeated 1000 hours
Refer to JIS C 5201-1 4.25
∆R : ± 2.0%
Damp Heat with Load
40 ± 2℃ with relative humidity 90% to
95%. Cycle repeated 1,000 hours
Refer to JIS C 5201-1 4.24
∆R : ± 2.0%
High Temperature Exposure Kept at 170℃ for 1,000 hours
Refer to JIS C 5201-1 4.23.2
Solderability
Mechanical Shock
Bending Test
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
=±
X.X
=±
X.XX = ±
ANGLES ± HOLE DIA. ±
∆R : ± 2.0%
Temperature of Solder : 245 ± 5℃
Immersion Duration : 3 ± 0.5 seconds
Refer to JIS C 5201-1 4.17
100 G’s for 6milliseconds. 5 pulses
Refer to JIS C 5201-1 4.21
Uniform coating of solder
cover minimum of 95%
surface being immersed
∆R : ± 1.0%
Glass-Epoxy board thickness : 1.6mm
Bending width : 2mm
Between the fulcrums : 90mm
Refer to JIS C 5201-1 4.33
∆R : ± 1.0%
DRAWN
BY ﹕ connie 4/3/13
DESIGNED BY ﹕
CHECKED
BY ﹕
APPROVED BY ﹕
SCALE ﹕ X
UNIT ﹕ X
Engineering Spec. For 1/2W 0612
TITLE : The
Low Resistance Chip Resistor
台達電子工業股份有限公司
Delta Electronics, Inc.
乾坤科技股份有限公司
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
NO.
SMN40000NH
PAGE 3
PAGE
REV.
A2
OF 6
6. Recommend Land Pattern
1632W
W
L
D
3.3
2.8
1.1
D
Unit : mm
W
Cu Trace
Note : We recommend there is no circuit design
Sensing Trace
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
=±
X.X
=±
X.XX = ±
ANGLES ± HOLE DIA. ±
DRAWN
BY ﹕ connie 4/3/13
DESIGNED BY ﹕
CHECKED
BY ﹕
APPROVED BY ﹕
SCALE ﹕ X
UNIT ﹕ X
Engineering Spec. For 1/2W 0612
TITLE : The
Low Resistance Chip Resistor
台達電子工業股份有限公司
Delta Electronics, Inc.
乾坤科技股份有限公司
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
NO.
SMN40000NH
PAGE 4
PAGE
REV.
A2
OF 6
7. Packaging
7-1 Dimensions
7-1-1 Tape packaging dimensions
0.3 max.
4.0±0.1
1.55±0.05
2.0 ± 0.1
1.75 ± 0.1
Sprocket hold
3.5 ± 0.05
8.0 ± 0.3
B
1.5 max.
A
4.0 ± 0.1
Carrier cavity
A = 2.0 ± 0.2
B = 3.5 ± 0.1
1.05 ± 0.05
Pulling direction
Unit : mm
7-1-2 Reel dimensions
2.0 ± 0.5
22 min.
Label
9.0 ± 0.3
Unit : mm
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
=±
X.X
=±
X.XX = ±
ANGLES ± HOLE DIA. ±
DRAWN
BY ﹕ connie 4/3/13
DESIGNED BY ﹕
CHECKED
BY ﹕
APPROVED BY ﹕
SCALE ﹕ X
UNIT ﹕ X
Engineering Spec. For 1/2W 0612
TITLE : The
Low Resistance Chip Resistor
56 ± 2.0
60 ± 1.0
178 ± 2.0
13.0 ± 0.2
11.4 ± 1.0
台達電子工業股份有限公司
Delta Electronics, Inc.
乾坤科技股份有限公司
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
NO.
SMN40000NH
PAGE 5
PAGE
REV.
A2
OF 6
7-2 Peel Strength of Top Cover Tape
The peel speed shall be about 300mm/minute
The peel force of top cover tape shall between 0.1 to 0.7N
Top Cover Tape
8
165 ~ 1
0°
0.1 ~ 0.7N
Carrier tape
7-3 Number of Taping
4,000 pieces / reel
7-4 Label marking
The following items shall be marked on the reel.
(1) Type designation
(2) Quantity
(3) Manufacturing date code
(4) Manufacturer’s name
(5) The country of origin
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
=±
X.X
=±
X.XX = ±
ANGLES ± HOLE DIA. ±
DRAWN
BY ﹕ connie 4/3/13
DESIGNED BY ﹕
CHECKED
BY ﹕
APPROVED BY ﹕
SCALE ﹕ X
UNIT ﹕ X
Engineering Spec. For 1/2W 0612
TITLE : The
Low Resistance Chip Resistor
台達電子工業股份有限公司
Delta Electronics, Inc.
乾坤科技股份有限公司
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
NO.
SMN40000NH
PAGE 6
PAGE
REV.
A2
OF 6