DAESAN RL1632-6C

1W, 1206, Low Resistance Chip Resistor (Lead free / Halogen Free)
1. Scope
This specification applies to 1.6mm x 3.2mm size 1W, fixed metal film chip resistors rectangular
type for use in electronic equipment.
2. Type Designation
□
RL1632
- 6C - □□□□
(1)
(2)
(3)
(4)
Where
(1) Series No.
(2) 6C = 1W
(3) Resistance value :
For example - Four digits of number
R005 = 5mΩ
R020 = 20mΩ
(4) Resistance tolerance
F = ± 1%
G = ± 2%
J = ± 5%
3. Outline Dimensions and Marking
L
Code Letter
1632
R010
W
t
L
3.2 ± 0.20
W
1.6 ± 0.20
a
0.50 ± 0.15
t
5mΩ: 1.05 ± 0.20
10~40mΩ: 0.90 ± 0.20
a
(Bottom View)
a
Dimensions (mm)
Four digits :
R010 = 10mΩ
R020 = 20mΩ
Figure 1. Construction Dimensions
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 1
PAGE
REV.
A2
OF 7
4.
Ratings
Power Ratings*
1W
Resistance Value
5~40mΩ
Resistance Tolerance
± 1%(F) , ± 2%(G) , ± 5%(J)
Temperature Coefficient of Resistance
(5mΩ)
(10~40mΩ)
Operation Temperature Range
0~300ppm/℃
± 100ppm/℃
-55℃ ~ +170℃
Insulation Resistance
Over 100MΩ
( P*R)1/2
Maximum Working Voltage (V)
Note * :
Power rating is based on continuous full load operation at rated ambient temperature of 70℃. For
RATED LOAD(%)
resistors operated at ambient temperature in excess of 70℃, the maximum load shall be derated in
accordance with the following curve.
100
0
-55
70
170
AMBIENT TEMPERATURE(℃)
Figure 2.:Power Temperature Derating Curve
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 2
PAGE
REV.
A2
OF 7
5. Characteristics
Test Item
Condition of Test
Requirements
Short Time Overload
2.5 * rated power for 5 seconds
Refer to JIS C 5201-1 4.13
∆R : ± 0.5%
Without significant damage by
flashover ( spark, arching ), burning
or breakdown etc.
Insulation Resistance
The resistor shall be cramped in the
metal block and tested , as shown below.
Test voltage : 100 ± 15VDC for 1 minute
Refer to JIS C 5201-1 4.6 Mounting
condition G.
Between Electrode and Protection
Film 100MΩ or over
Between Electrode and Substrate
1,000MΩ or over
Voltage Proof
The voltage : 100VAC (rms.) for 1 minute ∆R : ± 0.5%
Refer to JIS C 5201-1 4.7
Without damage by flashover, fire
or breakdown, as shown below.
Thermal Shock
-55 ~155℃ 100 cycles, 15 min at each
extreme condition
Refer to JIS C 5201-1 4.19
∆R : ± 1.0%
Without distinct damage in
appearance
Low Temperature Storage
Kept at -55℃, 1,000 hours
Refer to JIS C 5201-1 4.23.4
∆R : ± 1.0%
Without distinct damage in
appearance
High Temperature Exposure
Kept at 170℃ for 1,000 hours
Refer to JIS C 5201-1 4.23.2
∆R : ± 1.0%
Without distinct damage in
appearance
Solderability
Temperature of Solder : 245 ± 5℃
Immersion Duration : 3 ± 0.5 second
Refer to JIS C 5201-1 4.17
Uniform coating of solder cover
minimum of 95% surface being
immersed
Resistance to Soldering Heat
Dipped into solder at 270 ± 5℃
for 10 ± 1 seconds
Refer to JIS C 5201-1 4.18
∆R : ± 0.5%
Without distinct deformation in
appearance
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 3
PAGE
REV.
A2
OF 7
Test Item
Condition of Test
Requirements
Load Life
Rated voltage for 1.5 hours followed by a
pause 0.5 hour at 70 ± 2℃.
Cycle repeated 1000 hours
Refer to JIS C 5201-1 4.25
∆R : ± 1.0%
Without distinct damage in
appearance
Damp Heat with Load
40 ± 2℃ with relative humidity 90% to
95%. D.C. rated voltage for 1.5 hours
ON and 30 minutes OFF. Cycle
repeated 1,000 hours
Refer to JIS C 5201-1 4.24
∆R : ± 0.5%
Without distinct damage in
appearance
Mechanical Shock
100 G’s for 6milliseconds. 5 pulses
Refer to JIS C 5201-1 4.21
∆R : ± 0.5%
Without mechanical damage such
as break
Bending Test
Glass-Epoxy board thickness : 1.6mm
Bending width : 2mm
Between the fulcrums : 90mm
Refer to JIS C 5201-1 4.33
∆R : ± 0.5%
Without mechanical damage such
as break
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 4
PAGE
REV.
A2
OF 7
6. Recommend Land Pattern
L
1632
W
(mm)
L
(mm)
t
D
(mm) (μm)
1.78
4.14
1.37
D
W
105
Cu
Trace
t: Copper foil minimum thickness of PCB
Sensing
Trace
Note : We recommend there is no circuit design between pads to avoid circuit short.
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 5
PAGE
REV.
A2
OF 7
7. Packaging
7-1 Dimensions
7-1-1 Tape packaging dimensions
0.3 max.
+0.1
2.0 ± 0.1
P
1.5 -0.0
1.75 ± 0.1
Sprocket hold
3.5 ± 0.05
8.0 ± 0.3
B
1.5 max.
A
4.0 ± 0.1
Carrier cavity
A = 2.0 ± 0.2
B = 3.6 ± 0.2
P(PITCH) = 4.0 ± 0.1
1.05 ± 0.05
Pulling direction
Unit : mm
7-1-2 Reel dimensions
2.0 ± 0.5
22 min.
Label
56 ± 2.0
9.0 ± 0.3
Unit : mm
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
60 ± 1.0
178 ± 2.0
13.0 ± 0.2
11.4 ± 1.0
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 6
PAGE
REV.
A2
OF 7
7-2 Peel Strength of Top Cover Tape
The peel speed shall be about 300mm/minute
The peel force of top cover tape shall between 0.1 to 0.7N
Top Cover Tape
8
165 ~ 1
0°
0.1 ~ 0.7N
Carrier tape
7-3 Number of Taping
4,000 pieces / reel
7-4 Label marking
The following items shall be marked on the reel.
(1)
(2)
(3)
(4)
Type designation
Quantity
Manufacturing date code
Manufacturer’s name
(5) The country of origin
UNLESS OTHERWISE SPECIFIED TOLERANCES ON ﹕
X
= ±
X.X
= ±
X.XX = ±
ANGLES ±
HOLE DIA. ±
SCALE :
UNIT :
台達電子工業股份有限公司
Delta Electronics, Inc.
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF Delta Electronics, Inc.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
TITLE : The Engineering Spec. For 1W 1206
Low Resistance Chip Resistor
DOCUMENT
NO.
SMJ60000NH
PAGE 7
PAGE
REV.
A2
OF 7