KERSEMI IRFR9120NPBF

PD-95020A
IRFR9120NPbF
IRFU9120NPbF
l
l
l
l
l
l
l
l
Ultra Low On-Resistance
P-Channel
Surface Mount (IRFR9120N)
Straight Lead (IRFU9120N)
Advanced Process Technology
Fast Switching
Fully Avalanche Rated
Lead-Free
HEXFET® Power MOSFET
D
VDSS = -100V
RDS(on) = 0.48Ω
G
ID = -6.6A
S
Description
Fifth Generation HEXFETs from International Rectifier
utilize advanced processing techniques to achieve
extremely low on-resistance per silicon area. This benefit,
combined with the fast switching speed and ruggedized
device design that HEXFET Power MOSFETs are well
known for, provides the designer with an extremely efficient
and reliable device for use in a wide variety of applications.
The D-Pak is designed for surface mounting using vapor
phase, infrared, or wave soldering techniques. The straight
lead version (IRFU series) is for through-hole mounting
applications. Power dissipation levels up to 1.5 watts are
possible in typical surface mount applications.
D-Pak
TO-252AA
I-Pak
TO-251AA
Absolute Maximum Ratings
ID @ TC = 25°C
ID @ TC = 100°C
IDM
PD @TC = 25°C
VGS
EAS
IAR
EAR
dv/dt
TJ
TSTG
Parameter
Max.
Continuous Drain Current, VGS @ -10V
Continuous Drain Current, VGS @ -10V
Pulsed Drain Current 
Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Single Pulse Avalanche Energy‚
Avalanche Current
Repetitive Avalanche Energy
Peak Diode Recovery dv/dt ƒ
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds
-6.6
-4.2
-26
40
0.32
± 20
100
-6.6
4.0
-5.0
-55 to + 150
Units
A
W
W/°C
V
mJ
A
mJ
V/ns
300 (1.6mm from case )
°C
Thermal Resistance
Parameter
RθJC
RθJA
RθJA
Junction-to-Case
Junction-to-Ambient (PCB mount)**
Junction-to-Ambient
www.kersemi.com
Typ.
Max.
Units
–––
–––
–––
3.1
50
110
°C/W
1
12/14/04
IRFR/U9120NPbF
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter
Drain-to-Source Breakdown Voltage
∆V(BR)DSS/∆TJ Breakdown Voltage Temp. Coefficient
RDS(on)
Static Drain-to-Source On-Resistance
VGS(th)
Gate Threshold Voltage
gfs
Forward Transconductance
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Min.
-100
–––
–––
-2.0
1.4
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
Typ.
–––
-0.11
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
14
47
28
31
LD
Internal Drain Inductance
–––
4.5
LS
Internal Source Inductance
–––
7.5
Ciss
Coss
Crss
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
–––
–––
–––
350
110
70
V(BR)DSS
IDSS
IGSS
Drain-to-Source Leakage Current
Max. Units
Conditions
–––
V
VGS = 0V, ID = -250µA
––– V/°C Reference to 25°C, ID = -1mA
0.48
Ω
VGS = -10V, I D = -3.9A „
-4.0
V
VDS = VGS, ID = -250µA
–––
S
VDS = -50V, ID = -4.0A†
-25
VDS = -100V, VGS = 0V
µA
-250
VDS = -80V, VGS = 0V, TJ = 150°C
100
VGS = 20V
nA
-100
VGS = -20V
27
ID = -4.0A
5.0
nC VDS = -80V
15
VGS = -10V, See Fig. 6 and 13 „†
–––
VDD = -50V
–––
ID = -4.0A
ns
–––
RG = 12 Ω
–––
RD =12 Ω, See Fig. 10 „†
D
Between lead,
–––
6mm (0.25in.)
nH
G
from package
–––
and center of die contact…
S
–––
VGS = 0V
–––
pF
VDS = -25V
–––
ƒ = 1.0MHz, See Fig. 5†
Source-Drain Ratings and Characteristics
IS
ISM
V SD
t rr
Qrr
ton
Parameter
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode) 
Diode Forward Voltage
Reverse Recovery Time
Reverse Recovery Charge
Forward Turn-On Time
Min. Typ. Max. Units
Conditions
D
MOSFET symbol
––– ––– -6.6
showing the
A
G
integral reverse
––– ––– -26
p-n junction diode.
S
––– ––– -1.6
V
TJ = 25°C, IS = -3.9A, VGS = 0V „
––– 100 150
ns
TJ = 25°C, IF = -4.0A
––– 420 630
nC di/dt = 100A/µs „†
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
IRFR/U9120NPbF
100
100
VGS
-15V
-10V
-8.0V
-7.0V
-6.0V
-5.5V
-5.0V
BOTTOM -4.5V
VGS
-15V
-10V
-8.0V
-7.0V
-6.0V
-5.5V
-5.0V
BOTTOM -4.5V
TOP
-I D , Drain-to-Source Current (A)
-I D , Drain-to-Source Current (A)
TOP
10
1
-4.5V
20µs PULSE WIDTH
TJ = 25 °C
0.1
0.1
1
10
100
10
1
-4.5V
0.1
0.1
2.5
R DS(on) , Drain-to-Source On Resistance
(Normalized)
-I D , Drain-to-Source Current (A)
100
TJ = 25 °C
TJ = 150 ° C
1
V DS = -50V
20µs PULSE WIDTH
4
5
6
7
8
9
-VGS , Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
10
100
Fig 2. Typical Output Characteristics
Fig 1. Typical Output Characteristics
0.1
1
-VDS , Drain-to-Source Voltage (V)
-VDS , Drain-to-Source Voltage (V)
10
20µs PULSE WIDTH
TJ = 150 °C
10
ID = -6.7A
2.0
1.5
1.0
0.5
0.0
-60 -40 -20
V GS = -10V
0
20
40
60
80 100 120 140 160
TJ , Junction Temperature ( °C)
Fig 4. Normalized On-Resistance
Vs. Temperature
IRFR/U9120NPbF
20
0V,
f = 1MHz
Cgs + Cgd , Cds SHORTED
Cgd
Cds + Cgd
-VGS , Gate-to-Source Voltage (V)
VGS =
Ciss =
Crss =
Coss =
600
Ciss
Coss
400
Crss
200
ID = -4.0 A
VDS =-80V
VDS =-50V
VDS =-20V
16
12
8
4
FOR TEST CIRCUIT
SEE FIGURE 13
0
0
1
10
0
100
5
10
15
20
25
QG , Total Gate Charge (nC)
-VDS , Drain-to-Source Voltage (V)
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
100
100
OPERATION IN THIS AREA LIMITED
BY RDS(on)
10us
10
-IID , Drain Current (A)
-ISD , Reverse Drain Current (A)
C, Capacitance (pF)
800
TJ = 150 ° C
TJ = 25 ° C
1
0.1
0.2
V GS = 0 V
0.8
1.4
2.0
-VSD ,Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
10
100us
1ms
1
10ms
TC = 25 °C
TJ = 150 °C
Single Pulse
0.1
2.6
1
10
100
-VDS , Drain-to-Source Voltage (V)
Fig 8. Maximum Safe Operating Area
1000
IRFR/U9120NPbF
8.0
VGS
-ID , Drain Current (A)
RD
VDS
D.U.T.
RG
6.0
+
VDD
-10V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
4.0
Fig 10a. Switching Time Test Circuit
2.0
td(on)
tr
t d(off)
tf
VGS
10%
0.0
25
50
75
100
125
150
TC , Case Temperature ( °C)
90%
VDS
Fig 9. Maximum Drain Current Vs.
Case Temperature
Fig 10b. Switching Time Waveforms
Thermal Response (Z thJC )
10
D = 0.50
1
0.20
0.10
0.05
0.1
0.01
0.00001
0.02
0.01
P DM
SINGLE PULSE
(THERMAL RESPONSE)
t1
t2
Notes:
1. Duty factor D = t 1 / t 2
2. Peak T J = P DM x Z thJC + TC
0.0001
0.001
0.01
0.1
1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
10
IRFR/U9120NPbF
L
VDS
- V
V DD
+ DD
D.U.T
RG
A
IAS
-20V
tp
DRIVER
0.01Ω
15V
Fig 12a. Unclamped Inductive Test Circuit
I AS
EAS , Single Pulse Avalanche Energy (mJ)
250
TOP
200
BOTTOM
ID
-1.7A
-2.5A
-3.9A
150
100
50
0
25
50
75
100
125
150
Starting TJ , Junction Temperature ( °C)
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
tp
V(BR)DSS
Fig 12b. Unclamped Inductive Waveforms
Current Regulator
Same Type as D.U.T.
50KΩ
QG
12V
-10V
.2µF
.3µF
QGS
QGD
D.U.T.
+VDS
VGS
VG
-3mA
Charge
Fig 13a. Basic Gate Charge Waveform
IG
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
IRFR/U9120NPbF
Peak Diode Recovery dv/dt Test Circuit
+
D.U.T*
ƒ
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
+
‚
-
-
„
+

RG
• dv/dt controlled by RG
• ISD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
VGS
*
+
-
VDD
Reverse Polarity of D.U.T for P-Channel
Driver Gate Drive
P.W.
Period
D=
P.W.
Period
[VGS=10V ] ***
D.U.T. ISD Waveform
Reverse
Recovery
Current
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
[VDD]
Forward Drop
Inductor Curent
Ripple ≤ 5%
*** VGS = 5.0V for Logic Level and 3V Drive Devices
Fig 14. For P-Channel HEXFETS
[ISD ]
IRFR/U9120NPbF
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak (TO-252AA) Part Marking Information
EXAMPLE: THIS IS AN IRFR120
WITH ASSEMBLY
LOT CODE 1234
ASSEMBLED ON WW 16, 1999
IN THE ASSEMBLY LINE "A"
PART NUMBER
INTERNATIONAL
RECTIFIER
LOGO
Note: "P" in assembly line position
indicates "Lead-Free"
IRFU120
12
916A
34
ASSEMBLY
LOT CODE
DATE CODE
YEAR 9 = 1999
WEEK 16
LINE A
OR
PART NUMBER
INTERNATIONAL
RECTIFIER
LOGO
IRFU120
12
ASSEMBLY
LOT CODE
34
DATE CODE
P = DESIGNATES LEAD-FREE
PRODUCT (OPTIONAL)
YEAR 9 = 1999
WEEK 16
A = ASSEMBLY SITE CODE
IRFR/U9120NPbF
I-Pak (TO-251AA) Package Outline
Dimensions are shown in millimeters (inches)
I-Pak (TO-251AA) Part Marking Information
EXAMPLE: T HIS IS AN IRF U120
WIT H AS SEMBLY
LOT CODE 5678
ASS EMB LED ON WW 19, 1999
IN T HE AS S EMBLY LINE "A"
INT ERNAT IONAL
RECT IF IER
LOGO
PART NUMBER
IRF U120
919A
56
78
AS SEMBLY
LOT CODE
Note: "P" in assembly line
position indicates "Lead-F ree"
DAT E CODE
YEAR 9 = 1999
WEEK 19
LINE A
OR
INT ERNAT IONAL
RECT IFIER
LOGO
PART NUMBER
IRF U120
56
ASS EMB LY
LOT CODE
78
DAT E CODE
P = DES IGNAT ES LEAD-FREE
PRODUCT (OPT IONAL)
YEAR 9 = 1999
WEEK 19
A = AS SEMB LY S IT E CODE
IRFR/U9120NPbF
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRR
16.3 ( .641 )
15.7 ( .619 )
12.1 ( .476 )
11.9 ( .469 )
FEED DIRECTION
16.3 ( .641 )
15.7 ( .619 )
8.1 ( .318 )
7.9 ( .312 )
FEED DIRECTION
NOTES :
1. CONTROLLING DIMENSION : MILLIMETER.
2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ).
3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm
NOTES :
1. OUTLINE CONFORMS TO EIA-481.
TRL